PANDATEL-FOBUS-MODEM-MIB

File: PANDATEL-FOBUS-MODEM-MIB.mib (7835 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
PANDATEL-MODEM-MIB

Imported symbols

enterprises DisplayString OBJECT-TYPE
mdmSpecifics device-id

Defined Types

FobusTableEntry  
SEQUENCE    
  mdmRack INTEGER
  mdmModem INTEGER
  mdmPosition INTEGER
  mdmModemName DisplayString
  mdmBackupStatus INTEGER
  mdmActiveLink INTEGER
  mdmOperationMode INTEGER
  mdmAlarmConditionPort1 INTEGER
  mdmAlarmConditionPort2 INTEGER
  mdmAlarmConditionPort3 INTEGER
  mdmTXLaserStatusPort2 INTEGER
  mdmTXLaserStatusPort3 INTEGER

Defined Values

fobus-modem 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.501
OBJECT IDENTIFIER    

fobus 1.3.6.1.4.1.760.1.1.2.1.10.501
OBJECT IDENTIFIER    

fobusModemTable 1.3.6.1.4.1.760.1.1.2.1.10.501.1
This table contains information about all FOBUS units in all racks.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FobusTableEntry

fobusTableEntry 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1
The index of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FobusTableEntry  

mdmRack 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.1
The index of the rack where the unit is installed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mdmModem 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.2
This entry displays the slot number where the corresponding unit is installed in the rack.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mdmPosition 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.3
This entry displays the location of the corresponding unit: 'local' or 'remote'. The unit which is plugged into a managed rack is 'local', the counterpart is 'remote'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

mdmModemName 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.5
The verbal name of this unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mdmBackupStatus 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.11
The backup status of the unit. The available values depend on the generation of the unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), inactive(2), active(3), not-available(4), available(5), disable(6)  


mdmOperationMode 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.66
This entry defines if data is transmitted via port 2 or port 3: 'forced-port2', 'forced-port3', 'automatic'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), forced-port2(3), forced-port3(4), automatic(5)  

mdmAlarmConditionPort1 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.110
The alarm trigger mode at port 1: 'disable', i.e. no alarm is triggered, or 'link-signal', i.e. an alarm is triggered if the link is down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), link-signal(3)  

mdmAlarmConditionPort2 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.111
The alarm trigger mode at port 2: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down, 'laser-fail', i.e. an alarm is triggered if the laser diode is defective, or 'no-link-signal-or-laser-fail', i.e. the link is down or the laser diode is defective.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), no-link-signal(3), laser-fail(4), no-link-signal-or-laser-fail(5)  

mdmAlarmConditionPort3 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.112
The alarm trigger mode at port 3: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down, 'laser-fail', i.e. an alarm is triggered if the laser diode is defective, or 'no-link-signal-or-laser-fail', i.e. the link is down or the laser diode is defective.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), no-link-signal(3), laser-fail(4), no-link-signal-or-laser-fail(5)  

mdmTXLaserStatusPort2 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.121
This entry indicates if the laser diode at port 2 is transmitting data ('enable') or not ('disable').
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

mdmTXLaserStatusPort3 1.3.6.1.4.1.760.1.1.2.1.10.501.1.1.122
This entry indicates if the laser diode at port 3 is transmitting data ('enable') or not ('disable').
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)