ONEACCESS-IPSEC-MIB

File: ONEACCESS-IPSEC-MIB.mib (6808 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB ONEACCESS-GLOBAL-REG

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Counter32 Integer32 IpAddress
Unsigned32 MODULE-COMPLIANCE OBJECT-GROUP
TimeInterval ifIndex oacMIBModules
oacExpIMIp oacExpIMIPSec

Defined Values

oacNatMIBModule 1.3.6.1.4.1.13191.1.100.675
Contact updated
MODULE-IDENTITY    

oacIPSecNotifications 1.3.6.1.4.1.13191.10.3.1.4.1
OBJECT IDENTIFIER    

oacIsakmpNotifications 1.3.6.1.4.1.13191.10.3.1.4.2
OBJECT IDENTIFIER    

oacIPSecSAcreated 1.3.6.1.4.1.13191.10.3.1.4.1.1
An IPSec SA created notification signifies that the device created an IPSec security association.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacIPSecSAremoved 1.3.6.1.4.1.13191.10.3.1.4.1.2
An IPSec SA removed notification signifies that the device removed an IPSec security association.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacIPSecCmapEnabled 1.3.6.1.4.1.13191.10.3.1.4.1.3
An IPSec crypto map enabled notification signifies that the device validated the crypto map attached to an interface and the crypto map becomes valid on this interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacIPSecCmapDisabled 1.3.6.1.4.1.13191.10.3.1.4.1.4
An IPSec crypto map disabled notification signifies that the device did not validate the crypto map attached to an interface and the crypto map becomes invalid on this interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacIPSecCpolEnabled 1.3.6.1.4.1.13191.10.3.1.4.1.5
An IPSec crypto map policy enabled notification signifies that the device validated the crypto map policy. configuration is considered as active and can be used by Isakmp daemon, or IPSec manual keying.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacIPSecCpolDisabled 1.3.6.1.4.1.13191.10.3.1.4.1.6
An IPSec crypto map policy disabled notification signifies that the device did not validate the crypto map policy. Configuration is considered as inactive and can not be used by Isakmp or manual IPSec manual keying.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacIPSecHwModuleDown 1.3.6.1.4.1.13191.10.3.1.4.1.7
An IPSec hardware module down notification signifies that the device can not use any hardware encryption module, because it is not activated, or it is not present on the device.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPBadProposal 1.3.6.1.4.1.13191.10.3.1.4.2.1
An ISAKMP bad proposal notification signifies that the device did not validate proposal for IPSec phase 1 with a remote peer.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPNoResponse 1.3.6.1.4.1.13191.10.3.1.4.2.2
An ISAKMP No Response notification signifies that the device was exchanging ISAKMP information with a remote ISAKMP peer, and the peer did not give any answer to the device.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPConnectionEstablished 1.3.6.1.4.1.13191.10.3.1.4.2.3
An ISAKMP Connection established notification signifies that the device established an ISAKMP connection with a remote ISAKMP device.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPConnectionRemoved 1.3.6.1.4.1.13191.10.3.1.4.2.4
An ISAKMP Connection removed notification signifies that the device removed an ISAKMP connection with a remote ISAKMP device, because the lifetime of the connection reached the limit, or a reset has been carried out on the device, either by using clear crypto isakmp sa, or by shutting down the IPSec working interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAMPIPSecConnectionEstablished 1.3.6.1.4.1.13191.10.3.1.4.2.5
An ISAKMP IPSec Connection established notification signifies that the ISAKMP daemon of the device successfully created an IPSec tunnel between two ISAKMP peers.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPIPSecConnectionRemoved 1.3.6.1.4.1.13191.10.3.1.4.2.6
An ISAKMP IPSec Connection removed notification signifies that the ISAKMP daemon of the device removed an IPSec connection, either because the lifetime of the IPSec session reached the limit, or because a reset has been carried out on the IPSec working interface of the device.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPUnknownPeer 1.3.6.1.4.1.13191.10.3.1.4.2.7
An ISAKMP unknown peer notification signifies that the device received an unknown isakmp request and did not process it.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPNotificationMsgReceived 1.3.6.1.4.1.13191.10.3.1.4.2.8
An ISAKMP notification message received notification signifies that the device received a notification from a known ISAKMP peer.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPNotificationMsgSent 1.3.6.1.4.1.13191.10.3.1.4.2.9
An ISAKMP notification message sent notification signifies that the device sent a notification to a known ISAKMP peer. Generally, a sent notification is due to a problem on the ISAKMP connection between two ISAKMP peers. For example, if received packet is malformed, a notification message is sent.
Status: current Access: read-only
NOTIFICATION-TYPE    

oacISAKMPDeadPeerDetected 1.3.6.1.4.1.13191.10.3.1.4.2.10
An ISAKMP Dead Peer detection signifies that the device detected a DPD when using ISAKMP keepalive.
Status: current Access: read-only
NOTIFICATION-TYPE