ODS-ENC-MIB

File: ODS-ENC-MIB.mib (59688 bytes)

Imported modules

RFC1155-SMI SNMPv2-TC RFC1158-MIB

Imported symbols

enterprises NetworkAddress IpAddress
Counter Gauge TimeTicks
OBJECT-TYPE DisplayString PhysAddress
snmp

Defined Types

BoxAddressEntry  
SEQUENCE    
  batPhysAddress PhysAddress
  batFirstPacket TimeTicks
  batLastPacket TimeTicks
  batGoodPackets Counter
  batGoodOctets Counter
  batCard INTEGER
  batPort INTEGER
  batDelete INTEGER
  batGoodPacketsTo Counter
  batGoodOctetsTo Counter
  batFirstPacketTo TimeTicks
  batLastPacketTo TimeTicks
  batLastIpAddress IpAddress

AddrProtoEntry  
SEQUENCE    
  apUnkPackets Counter
  apIPPackets Counter
  apISOPackets Counter
  apDECPackets Counter
  apNWPackets Counter
  apATPackets Counter
  apXNSPackets Counter
  apSNAPackets Counter
  apUnkOctets Counter
  apIPOctets Counter
  apISOOctets Counter
  apDECOctets Counter
  apNWOctets Counter
  apATOctets Counter
  apXNSOctets Counter
  apSNAOctets Counter
  apPhysAddress PhysAddress

CardEntry  
SEQUENCE    
  cardIndex INTEGER
  cardId INTEGER
  cardDescr DisplayString
  cardOperStatus INTEGER
  cardAdminStatus INTEGER
  cardGoodPackets Counter
  cardGoodOctets Counter
  cardNumAddresses Counter
  cardCrcErrors Counter
  cardAlignErrors Counter
  cardFragErrors Counter
  cardPacketThresh Gauge
  cardCrcThresh Gauge
  cardAlignThresh Gauge
  cardFragThresh Gauge
  cardNumPorts INTEGER
  cardOctetThresh Gauge
  cardNetworkMode INTEGER

PortEntry  
SEQUENCE    
  portCard INTEGER
  portIndex INTEGER
  portOperStatus INTEGER
  portAdminStatus INTEGER
  portGoodPackets Counter
  portGoodOctets Counter
  portNumAddresses Counter
  portCrcErrors Counter
  portAlignErrors Counter
  portFragErrors Counter
  portPacketThresh Gauge
  portCrcThresh Gauge
  portAlignThresh Gauge
  portFragThresh Gauge
  portOctetThresh Gauge
  portLinkStatus INTEGER
  portAutoOffEnable INTEGER
  portAddrTrapEnable INTEGER

AdminAccessEntry  
SEQUENCE    
  accIndex INTEGER
  accCommunity OCTET STRING
  accPrivilege INTEGER
  accDelete INTEGER

AdminTrapEntry  
SEQUENCE    
  trapCommunity OCTET STRING
  trapDestAddress IpAddress
  trapBoxEnable INTEGER
  trapCardEnable INTEGER
  trapPortEnable INTEGER
  trapAddrEnable INTEGER
  trapStdEnable INTEGER
  trapDelete INTEGER

Defined Values

ods 1.3.6.1.4.1.50
OBJECT IDENTIFIER    

enc 1.3.6.1.4.1.50.1
OBJECT IDENTIFIER    

encMib2 1.3.6.1.4.1.50.1.2
OBJECT IDENTIFIER    

encSystem 1.3.6.1.4.1.50.1.2.1
OBJECT IDENTIFIER    

encAdmin 1.3.6.1.4.1.50.1.2.2
OBJECT IDENTIFIER    

encBox 1.3.6.1.4.1.50.1.2.1.1
OBJECT IDENTIFIER    

encCards 1.3.6.1.4.1.50.1.2.1.2
OBJECT IDENTIFIER    

encPorts 1.3.6.1.4.1.50.1.2.1.3
OBJECT IDENTIFIER    

encExper 1.3.6.1.4.1.50.1.3
OBJECT IDENTIFIER    

encProtos 1.3.6.1.4.1.50.1.3.1
OBJECT IDENTIFIER    

boxProtos 1.3.6.1.4.1.50.1.3.1.1
OBJECT IDENTIFIER    

addrProtos 1.3.6.1.4.1.50.1.3.1.2
OBJECT IDENTIFIER    

boxId 1.3.6.1.4.1.50.1.2.1.1.1
The type of chassis used in the concentrator. For modular concentrators, the hardware is further qualifed by the value of cardId for each card installed in the concentrator.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ods296(5), ods292(6), ods295(7), ods290-red(9), ods293-red(10), ods258(11), ods293(12), ods291(13), ods290(14), ods263(134), ods261(135), ods251(139), ods243(142), ods241(143)  

boxDescr 1.3.6.1.4.1.50.1.2.1.1.2
A textual description of the chassis including the ODS model number, media type and number of slots. For modular concentrators, the hardware is further qualified by the value of cardDescr for each card installed in the concentrator.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

boxNetworkMode 1.3.6.1.4.1.50.1.2.1.1.3
The state of the network interface port. If the value is network(2), the concentrator may be cas- caded off of another network. Regardless of the value, the concentrator may also be connected to other networks via normal interface ports. Note that the functionality previously provided by this object has been superceded by portOperStatus and portAdminStatus as all external connections on the concentrator are available through the portTable. This object may be deleted from future versions of the MIB.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2)  

boxPowerStatus 1.3.6.1.4.1.50.1.2.1.1.20
The state of the power supplies in the concentrator. The value is a sum. For each power supply P, in the range 1 through 2, that is operational, 2 raised to (P - 1) is added to the sum. For example, if both power supplies are good, the value is 3 (2^0 + 2^1). In contrast, if power supply 2 is bad, the value is 1 (2^0). Note that the value will be NULL for those concentrators which can not access the power supply status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boxNumAddresses 1.3.6.1.4.1.50.1.2.1.1.7
The number of unique, physical, source and dest- ination addresses contained in non-errored packets received by the concentrator. Note that this object is not maintained if the value of adminAddrStat- Enable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boxGoodPackets 1.3.6.1.4.1.50.1.2.1.1.5
The number of non-errored packets received by the concentrator. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boxGoodOctets 1.3.6.1.4.1.50.1.2.1.1.6
The number of octets contained in non-errored packets received by the concentrator. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boxCrcErrors 1.3.6.1.4.1.50.1.2.1.1.10
The number of packets received by the concen- trator which had CRC errors. Note that this object is not maintained if the value of adminPktStat- Enable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boxAlignErrors 1.3.6.1.4.1.50.1.2.1.1.11
The number of packets received by the concen- trator which had frame alignment errors. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boxFragErrors 1.3.6.1.4.1.50.1.2.1.1.12
The number of packets received by the concen- trator which contained fewer than 64 octets. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boxPacketThresh 1.3.6.1.4.1.50.1.2.1.1.13
A threshold for monitoring the number of non- errored packets received by the concentrator. If the measured number of packets per second equals or exceeds this value, a box-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of non-errored packets per second received by the concentrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

boxOctetThresh 1.3.6.1.4.1.50.1.2.1.1.19
A threshold for monitoring the number of octets contained in non-errored packets received by the concentrator. If the measured number of octets per second equals or exceeds this value, a box- class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of octets per second contained in non-errored packets received by the concentrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

boxCrcThresh 1.3.6.1.4.1.50.1.2.1.1.14
A threshold for monitoring the number of packets received by the concentrator which had CRC errors. If the measured number of packets per second equals or exceeds this value, a box-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per second received by the concentrator which had CRC errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

boxAlignThresh 1.3.6.1.4.1.50.1.2.1.1.15
A threshold for monitoring the number of packets received by the concentrator which had frame alignment errors. If the measured number of packets per second equals or exceeds this value, a box-class trap will be sent to each network manager defined in the adminTrapTable. Monitor- ing of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per second received by the concentrator which had frame alignment errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

boxFragThresh 1.3.6.1.4.1.50.1.2.1.1.16
A threshold for monitoring the number of packets received by the concentrator which contained fewer than 64 octets. If the measured number of packets per second equals or exceeds this value, a box-class trap will be sent to each network manager defined in the adminTrapTable. Monitor- ing of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per second received by the concentrator which contained fewer than 64 octets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

boxMissedPackets 1.3.6.1.4.1.50.1.2.1.1.9
The number of packets received by the concen- trator which could not be processed by the agent due to excessive network traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boxLostPackets 1.3.6.1.4.1.50.1.2.1.1.8
The number of packets received by the concen- trator which could not be attributed to a card and port by the agent. This object is not main- tained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpUnkPackets 1.3.6.1.4.1.50.1.3.1.1.1
The number of non-errored packets received by the concentrator having an unknown protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpIPPackets 1.3.6.1.4.1.50.1.3.1.1.2
The number of non-errored packets received by the concentrator having a DOD (IP, ARP, RARP) protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpISOPackets 1.3.6.1.4.1.50.1.3.1.1.3
The number of non-errored packets received by the concentrator having an ISO protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpDECPackets 1.3.6.1.4.1.50.1.3.1.1.4
The number of non-errored packets received by the concentrator having a DEC protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpNWPackets 1.3.6.1.4.1.50.1.3.1.1.5
The number of non-errored packets received by the concentrator having a NetWare protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpATPackets 1.3.6.1.4.1.50.1.3.1.1.6
The number of non-errored packets received by the concentrator having an AppleTalk protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpXNSPackets 1.3.6.1.4.1.50.1.3.1.1.7
The number of non-errored packets received by the concentrator having an XNS protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpSNAPackets 1.3.6.1.4.1.50.1.3.1.1.8
The number of non-errored packets received by the concentrator having an SNA protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpUnkOctets 1.3.6.1.4.1.50.1.3.1.1.9
The number of octets contained in non-errored packets received by the concentrator having an unknown protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpIPOctets 1.3.6.1.4.1.50.1.3.1.1.10
The number of octets contained in non-errored packets received by the concentrator having a DOD (IP, ARP, RARP) protocol type. Note that this object is not maintained if the value of admin- ProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpISOOctets 1.3.6.1.4.1.50.1.3.1.1.11
The number of octets contained in non-errored packets received by the concentrator having an ISO protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpDECOctets 1.3.6.1.4.1.50.1.3.1.1.12
The number of octets contained in non-errored packets received by the concentrator having a DEC protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpNWOctets 1.3.6.1.4.1.50.1.3.1.1.13
The number of octets contained in non-errored packets received by the concentrator having a NetWare protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpATOctets 1.3.6.1.4.1.50.1.3.1.1.14
The number of octets contained in non-errored packets received by the concentrator having an AppleTalk protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpXNSOctets 1.3.6.1.4.1.50.1.3.1.1.15
The number of octets contained in non-errored packets received by the concentrator having an XNS protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bpSNAOctets 1.3.6.1.4.1.50.1.3.1.1.16
The number of octets contained in non-errored packets received by the concentrator having an SNA protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boxAddressTable 1.3.6.1.4.1.50.1.2.1.1.18
A list of address entries for each physical address contained in non-errored packets received by the concentrator. The number of entries is given by the value of boxNumAddresses. Note that no entries are maintained if the value of admin- AddrStatEnable is disabled(2).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BoxAddressEntry

boxAddressEntry 1.3.6.1.4.1.50.1.2.1.1.18.1
An address entry containing objects pertaining to a physical address contained in non-errored packets received by the concentrator.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BoxAddressEntry  

batCard 1.3.6.1.4.1.50.1.2.1.1.18.1.6
The card on which the most recent, non-errored packet having the address as source was received. The card identified by this value is the same card as identified by the same value of cardIndex. Note that the value will be NULL for addresses which have not transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

batPort 1.3.6.1.4.1.50.1.2.1.1.18.1.7
The port on which the most recent, non-errored packet having the address as source was received. The port identified by this value is the same port as identified by the same value of portIndex. Note that the value will be NULL for addresses which have not transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

batPhysAddress 1.3.6.1.4.1.50.1.2.1.1.18.1.1
The physical address for this entry. When reported in a trap, the physical address relevant to the trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress Size(6)  

batLastIpAddress 1.3.6.1.4.1.50.1.2.1.1.18.1.13
The source network address used in the most recent IP packet received by the concentrator having the address as source. Note that the value will be NULL for addresses which have not transmitted any IP packets or if the value of adminIpCheckEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

batGoodPackets 1.3.6.1.4.1.50.1.2.1.1.18.1.4
The number of non-errored packets received by the concentrator having the address as source.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

batGoodOctets 1.3.6.1.4.1.50.1.2.1.1.18.1.5
The number of octets contained in non-errored packets received by the concentrator having the address as source.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

batFirstPacket 1.3.6.1.4.1.50.1.2.1.1.18.1.2
The value of sysUpTime at the time the first packet having the address as source was received by the concentrator. Note that the value will be NULL for addresses which have not transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

batLastPacket 1.3.6.1.4.1.50.1.2.1.1.18.1.3
The value of sysUpTime at the time the most recent packet having the address as source was received by the concentrator. Note that the value will be NULL for addresses which have not transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

batGoodPacketsTo 1.3.6.1.4.1.50.1.2.1.1.18.1.9
The number of non-errored packets received by the concentrator having the address as dest- ination.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

batGoodOctetsTo 1.3.6.1.4.1.50.1.2.1.1.18.1.10
The number of octets contained in non-errored packets received by the concentrator having the address as destination.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

batFirstPacketTo 1.3.6.1.4.1.50.1.2.1.1.18.1.11
The value of sysUpTime at the time the first packet having the address as destination was received by the concentrator. Note that the value will be NULL for addresses which have not been sent packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

batLastPacketTo 1.3.6.1.4.1.50.1.2.1.1.18.1.12
The value of sysUpTime at the time the most recent packet having the address as destination was received by the concentrator. Note that the value will be NULL for addresses which have not been sent packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

batDelete 1.3.6.1.4.1.50.1.2.1.1.18.1.8
Setting this object to any legal, ASN.1 value deletes the entry for the address.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

addrProtoTable 1.3.6.1.4.1.50.1.3.1.2.1
A list of protocol entries for each physical address contained in non-errored packets received by the concentrator. The number of entries is given by the value of boxNumAddresses. Note that no entries are maintained if the value of admin- AddrStatEnable is disabled(2).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AddrProtoEntry

addrProtoEntry 1.3.6.1.4.1.50.1.3.1.2.1.1
A protocol entry containing objects pertaining to a physical address contained in non-errored packets received by the concentrator.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AddrProtoEntry  

apPhysAddress 1.3.6.1.4.1.50.1.3.1.2.1.1.17
The physical address for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress Size(6)  

apUnkPackets 1.3.6.1.4.1.50.1.3.1.2.1.1.1
The number of non-errored packets received by the concentrator having the address as source and an unknown protocol type. Note that this object is not maintained if the value of adminProtStat- Enable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apIPPackets 1.3.6.1.4.1.50.1.3.1.2.1.1.2
The number of non-errored packets received by the concentrator having the address as source and a DOD (IP, ARP, RARP) protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apISOPackets 1.3.6.1.4.1.50.1.3.1.2.1.1.3
The number of non-errored packets received by the concentrator having the address as source and an ISO protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apDECPackets 1.3.6.1.4.1.50.1.3.1.2.1.1.4
The number of non-errored packets received by the concentrator having the address as source and a DEC protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apNWPackets 1.3.6.1.4.1.50.1.3.1.2.1.1.5
The number of non-errored packets received by the concentrator having the address as source and a NetWare protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apATPackets 1.3.6.1.4.1.50.1.3.1.2.1.1.6
The number of non-errored packets received by the concentrator having the address as source and an AppleTalk protocol type. Note that this object is not maintained if the value of adminProtStat- Enable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apXNSPackets 1.3.6.1.4.1.50.1.3.1.2.1.1.7
The number of non-errored packets received by the concentrator having the address as source and an XNS protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apSNAPackets 1.3.6.1.4.1.50.1.3.1.2.1.1.8
The number of non-errored packets received by the concentrator having the address as source and an SNA protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apUnkOctets 1.3.6.1.4.1.50.1.3.1.2.1.1.9
The number of octets contained in non-errored packets received by the concentrator having the address as source and an unknown protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apIPOctets 1.3.6.1.4.1.50.1.3.1.2.1.1.10
The number of octets contained in non-errored packets received by the concentrator having the address as source and a DOD (IP, ARP, RARP) protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apISOOctets 1.3.6.1.4.1.50.1.3.1.2.1.1.11
The number of octets contained in non-errored packets received by the concentrator having the address as source and an ISO protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apDECOctets 1.3.6.1.4.1.50.1.3.1.2.1.1.12
The number of octets contained in non-errored packets received by the concentrator having the address as source and a DEC protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apNWOctets 1.3.6.1.4.1.50.1.3.1.2.1.1.13
The number of octets contained in non-errored packets received by the concentrator having the address as source and a NetWare protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apATOctets 1.3.6.1.4.1.50.1.3.1.2.1.1.14
The number of octets contained in non-errored packets received by the concentrator having the address as source and an AppleTalk protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apXNSOctets 1.3.6.1.4.1.50.1.3.1.2.1.1.15
The number of octets contained in non-errored packets received by the concentrator having the address as source and an XNS protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apSNAOctets 1.3.6.1.4.1.50.1.3.1.2.1.1.16
The number of octets contained in non-errored packets received by the concentrator having the address as source and an SNA protocol type. Note that this object is not maintained if the value of adminProtStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cardNumSlots 1.3.6.1.4.1.50.1.2.1.2.1
The number of slots in the concentrator. For modular concentrators, this value is the maximum number of cards that can be installed. For non-modular concentrators, the value is always two (card one contains the user ports and card two contains the network port).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cardNumCards 1.3.6.1.4.1.50.1.2.1.2.2
The number of cards actually installed in the concentrator. For non-modular concentrators, the value is always two (card one contains the user ports and card two contains the network port).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cardTable 1.3.6.1.4.1.50.1.2.1.2.3
A list of card entries for each card installed in the concentrator. The number of entries is given by the value of cardNumCards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CardEntry

cardEntry 1.3.6.1.4.1.50.1.2.1.2.3.1
A card entry containing objects pertaining to a card installed in the concentrator.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CardEntry  

cardIndex 1.3.6.1.4.1.50.1.2.1.2.3.1.1
The slot in which the card is installed. This value uniquely identifies the card. Its value ranges between 1 and the value of cardNumSlots. When reported in a trap, the card relevant to the trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cardId 1.3.6.1.4.1.50.1.2.1.2.3.1.2
The type of card installed in the concentrator. For non-modular concentrators, the value is the same as that of boxId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ods294-e(1), ods294-8(4), ods294-7(5), ods294-9(6), ods294-btC(8), ods294-fr(9), ods294-fo(10), ods294-aui(11), ods294-tp(12), ods294-btB(13), ods294-bts(14), ods294-btm(15), ods294-tn(24), ods294-ts8(27), ods294-ts16(28), ods294-br(29), ods294-sam(30), ods294-tfr(31), ods294-trf(45), ods294-tr9(46), ods294-rj(47), ods294-rc(59), starnet(128), ods263(134), ods261(135), ods251(139), ods243(142), ods241(143)  

cardDescr 1.3.6.1.4.1.50.1.2.1.2.3.1.3
A textual description of the card including the ODS model number, media type and number of ports. For non-modular concentrators, the value is the same as that of boxDescr.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cardOperStatus 1.3.6.1.4.1.50.1.2.1.2.3.1.4
The current operational state of the card. Note that this object currently has no meaning and may be deleted from future versions of the MIB.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cardAdminStatus 1.3.6.1.4.1.50.1.2.1.2.3.1.5
The desired state of the card. Note that this object currently has no meaning and may be deleted from future versions of the MIB.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cardNetworkMode 1.3.6.1.4.1.50.1.2.1.2.3.1.18
The state of the back-plane connection on the card. If the value is stand-alone(3), the ports on the card form a separate, isolated network from the rest of the cards in the concentrator. If the value is unsupported(1), the card is always connected and can not be changed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unsupported(1), connected(2), stand-alone(3)  

cardNumPorts 1.3.6.1.4.1.50.1.2.1.2.3.1.16
The number of configurable ports on the card. For some cards, the value may be zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cardNumAddresses 1.3.6.1.4.1.50.1.2.1.2.3.1.8
The number of unique, physical, source addresses contained in non-errored packets received on the card. Note that this object is not maintained if the value of adminAddrStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cardGoodPackets 1.3.6.1.4.1.50.1.2.1.2.3.1.6
The number of non-errored packets received on the card. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cardGoodOctets 1.3.6.1.4.1.50.1.2.1.2.3.1.7
The number of octets contained in non-errored packets received on the card. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cardCrcErrors 1.3.6.1.4.1.50.1.2.1.2.3.1.9
The number of packets received on the card which had CRC errors. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cardAlignErrors 1.3.6.1.4.1.50.1.2.1.2.3.1.10
The number of packets received on the card which had frame alignment errors. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cardFragErrors 1.3.6.1.4.1.50.1.2.1.2.3.1.11
The number of packets received on the card which contained fewer than 64 octets. Note that this object is not maintained if the value of admin- PktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cardPacketThresh 1.3.6.1.4.1.50.1.2.1.2.3.1.12
A threshold for monitoring the number of non- errored packets received on the card. If the measured number of packets per second equals or exceeds this value, a card-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of non-errored packets per second received on the card.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

cardOctetThresh 1.3.6.1.4.1.50.1.2.1.2.3.1.17
A threshold for monitoring the number of octets contained in non-errored packets received on the card. If the measured number of octets per second equals or exceeds this value, a card-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of octets per second contained in non-errored second received on the card.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

cardCrcThresh 1.3.6.1.4.1.50.1.2.1.2.3.1.13
A threshold for monitoring the number of packets received on the card which had CRC errors. If the measured number of packets per second equals or exceeds this value, a card-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per second received on the card which had CRC errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

cardAlignThresh 1.3.6.1.4.1.50.1.2.1.2.3.1.14
A threshold for monitoring the number of packets received on the card which had frame alignment errors. If the measured number of packets per second equals or exceeds this value, a card-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per second received on the card which had frame alignment errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

cardFragThresh 1.3.6.1.4.1.50.1.2.1.2.3.1.15
A threshold for monitoring the number of packets received on the card which contained fewer than 64 octets. If the measured number of packets per second equals or exceeds this value, a card-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per second received on the card which contained fewer than 64 octets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

portTable 1.3.6.1.4.1.50.1.2.1.3.1
A list of port entries for each interface port in the concentrator. The number of entries is given by the sum of cardNumPorts for each card in the cardTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 1.3.6.1.4.1.50.1.2.1.3.1.1
A port entry containing objects pertaining to an interface port in the concentrator.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortEntry  

portCard 1.3.6.1.4.1.50.1.2.1.3.1.1.1
The card on which the port exists. The card identified by this value is the same card as identified by the same value of cardIndex. When reported in a trap, the card relevant to the trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portIndex 1.3.6.1.4.1.50.1.2.1.3.1.1.2
An integer which uniquely identifes this port on the card. Its value ranges between 1 and the value of cardNumPorts for the card. When reported in a trap, the port relevant to the trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portOperStatus 1.3.6.1.4.1.50.1.2.1.3.1.1.3
The current operational state of the port. If the value is down(2), no data is passed through the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

portAdminStatus 1.3.6.1.4.1.50.1.2.1.3.1.1.4
The desired state of the port. If the value is down(2), no data is passed through the port. When reported in a trap, the new state of the port. If the value is down(2), the port was turned off as a result of the auto-shutoff feature being enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

portLinkStatus 1.3.6.1.4.1.50.1.2.1.3.1.1.16
The link status for the port. For media types that do not support link status, the value is always unsupported(1). When reported in a trap, the new link status of the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unsupported(1), link-good(2), partitioned(3), no-link(4)  

portAutoOffEnable 1.3.6.1.4.1.50.1.2.1.3.1.1.17
The state of the auto-shutoff feature for the port. If the value is enabled(1), the value of portAdminStatus for the port will be changed to down(1) whenever a port threshold is exceeded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portAddrTrapEnable 1.3.6.1.4.1.50.1.2.1.3.1.1.18
The state of the new-address detection feature for the port. If the value is enabled(1), a newAddressTrap will be generated whenever a new, physical, source address is contained in a packet received by the concentrator on the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portNumAddresses 1.3.6.1.4.1.50.1.2.1.3.1.1.7
The number of unique, physical, source addresses contained in non-errored packets received on the port. Note that this object is not maintained if the value of adminAddrStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portGoodPackets 1.3.6.1.4.1.50.1.2.1.3.1.1.5
The number of non-errored packets received on the port. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portGoodOctets 1.3.6.1.4.1.50.1.2.1.3.1.1.6
The number of octets contained in non-errored packets received on the port. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portCrcErrors 1.3.6.1.4.1.50.1.2.1.3.1.1.8
The number of packets received on the port which had CRC errors. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portAlignErrors 1.3.6.1.4.1.50.1.2.1.3.1.1.9
The number of packets received on the port which had frame alignment errors. Note that this object is not maintained if the value of adminPktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portFragErrors 1.3.6.1.4.1.50.1.2.1.3.1.1.10
The number of packets received on the port which contained fewer than 64 octets. Note that this object is not maintained if the value of admin- PktStatEnable is disabled(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portPacketThresh 1.3.6.1.4.1.50.1.2.1.3.1.1.11
A threshold for monitoring the number of non- errored packets received on the port. If the measured number of packets per second equals or exceeds this value, a port-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of non-errored packets per second received on the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

portOctetThresh 1.3.6.1.4.1.50.1.2.1.3.1.1.15
A threshold for monitoring the number of octets contained in non-errored packets received on the port. If the measured number of octets per second equals or exceeds this value, a port-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of octets per second contained in non-errored second received on the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

portCrcThresh 1.3.6.1.4.1.50.1.2.1.3.1.1.12
A threshold for monitoring the number of packets received on the port which had CRC errors. If the measured number of packets per second equals or exceeds this value, a port-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per secondreceived on the port which had CRC errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

portAlignThresh 1.3.6.1.4.1.50.1.2.1.3.1.1.13
A threshold for monitoring the number of packets received on the port which had frame alignment errors. If the measured number of packets per second equals or exceeds this value, a port-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per second received on the port which had frame alignment errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

portFragThresh 1.3.6.1.4.1.50.1.2.1.3.1.1.14
A threshold for monitoring the number of packets received on the port which contained fewer than 64 octets. If the measured number of packets per second equals or exceeds this value, a port-class trap will be sent to each network manager defined in the adminTrapTable. Monitoring of this threshold is disabled if the value is zero or if the value of adminPktStatEnable is disabled(2). When reported in a trap, the measured number of packets per second received on the port which contained fewer than 64 octets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

adminReboot 1.3.6.1.4.1.50.1.2.2.16
Setting this object to any legal, ASN.1 value recycles the management agent in the concentrator.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

adminLocalTime 1.3.6.1.4.1.50.1.2.2.1
The local time of day at the concentrator. The value is a string of three binary-coded-decimal octets in the form HH MM SS, where HH is the hour (24 hour format), MM is the minutes and SS is the seconds. The local time of day is only used for out-of- band management via the asynchronous port on the concentrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adminLocalDate 1.3.6.1.4.1.50.1.2.2.2
The local date at the concentrator. The value is a string of three binary-coded-decimal octets in the form YY MM DD, where YY is the year, MM is the month and DD is the day. The local date is only used for out-of-band management via the asynchronous port on the concentrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adminSecureTerm 1.3.6.1.4.1.50.1.2.2.17
The status of the out-of-band interface. If the value is secured(1), the user is be required to enter a super-user level community name before any management functions can be accessed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER secured(1), unsecured(2)  

adminPrivilege 1.3.6.1.4.1.50.1.2.2.9
The access privilege afforded the community name used in the requesting PDU. This value allows a network manager to easily determine its ability to read and write protected objects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER read-only(1), read-write(2), super-user(3)  

adminTrapId 1.3.6.1.4.1.50.1.2.2.7
The number of unique traps generated by the agent since it was reset. When reported in a trap, an integer which uniquely identifies the trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminTrapAddress 1.3.6.1.4.1.50.1.2.2.8
When reported in a trap, the source IP address of a PDU which resulted in an authentication failure.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpAddress  

adminPktStatEnable 1.3.6.1.4.1.50.1.2.2.12
The state of the packet statistics collection feature. If the value is enabled(1), the management agent will maintain statistics for all packets received by the concentrator on a box, card and port basis. The value is normally enabled(1). It should only be set to disabled(2) during periods of excessively high network traffic when the management agent must remain available for other management activities.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adminAddrStatEnable 1.3.6.1.4.1.50.1.2.2.13
The state of the address statistics collection feature. If the value is enabled(1), the manage- ment agent will maintain statistics for all packets received by the concentrator on a physical, source and destination address basis. The value is normally enabled(1) but can be set to disabled(2) when address-related statistics are not needed. It should be set to disabled(2) during periods of excessively high network traffic when the management agent must remain available for other management activities.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adminProtStatEnable 1.3.6.1.4.1.50.1.2.2.14
The state of the protocol statistics collection feature. If the value is enabled(1), the manage- ment agent will maintain statistics for all packets received by the concentrator on a top-level protocol basis. The value is normally disabled(2). It should only be set to enabled(1) when protocol-related statis- tics are needed as it adversely affects performance of the management agent in the concetrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adminIpCheckEnable 1.3.6.1.4.1.50.1.2.2.15
The state of the IP address detection feature. If the value is enabled(1) and the value of adminAddr- StatEnable is also enabled(1), the management agent will detect the IP address used by each physical source address in any TCP/IP packets received by the concentrator. The value is normally disabled(2). It should only be set to enabled(1) when protocol-related statis- tics are needed as it adversely affects performance of the management agent in the concetrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

accMaxEntries 1.3.6.1.4.1.50.1.2.2.10
The maximum number of access privilege entries allowed in adminAccessTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminAccessTable 1.3.6.1.4.1.50.1.2.2.5
A list of access entries mapping community names into access privileges. The maximum number of entries is given by accMaxEntries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdminAccessEntry

adminAccessEntry 1.3.6.1.4.1.50.1.2.2.5.1
An access entry which maps a community name into an access privilege.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdminAccessEntry  

accIndex 1.3.6.1.4.1.50.1.2.2.5.1.1
An integer which uniquely identifies this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accCommunity 1.3.6.1.4.1.50.1.2.2.5.1.2
The community name for the entry. Setting this object to a null string effectively invalidates the entry. However, accDelete should be used to delete entries as it resets all parameters to default settings.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accPrivilege 1.3.6.1.4.1.50.1.2.2.5.1.3
The access privilege afforded the community name in the entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER read-only(1), read-write(2), super-user(3)  

accDelete 1.3.6.1.4.1.50.1.2.2.5.1.4
Setting this object to any legal, ASN.1 value deletes the entry for the community name.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

trapMaxEntries 1.3.6.1.4.1.50.1.2.2.11
The maximum number of network manager entries allowed in adminTrapTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminTrapTable 1.3.6.1.4.1.50.1.2.2.6
A list of trap entries for each network manager which receives traps from the agent. The maximum number of entries is given by trapMaxEntries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdminTrapEntry

adminTrapEntry 1.3.6.1.4.1.50.1.2.2.6.1
A trap entry containing objects pertaining to a network manager which receives traps from the agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdminTrapEntry  

trapDestAddress 1.3.6.1.4.1.50.1.2.2.6.1.3
The IP address of the management station to receive traps. Note that setting this object to a value of all zeros effectively invalidates the entry. However, trapDelete should be used to delete entries as it resets all parameters to default settings.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

trapCommunity 1.3.6.1.4.1.50.1.2.2.6.1.2
The community name used in traps sent to the management station.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

trapStdEnable 1.3.6.1.4.1.50.1.2.2.6.1.8
The state of the standard-class trap enable for the management station. If the value is disabled(2), standard SNMP traps will not be sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

trapBoxEnable 1.3.6.1.4.1.50.1.2.2.6.1.4
The state of the box-class trap enable for the management station. If the value is disabled(2), box-class traps will not be sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

trapCardEnable 1.3.6.1.4.1.50.1.2.2.6.1.5
The state of the card-class trap enable for the management station. If the value is disabled(2), card-class traps will not be sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

trapPortEnable 1.3.6.1.4.1.50.1.2.2.6.1.6
The state of the port-class trap enable for the management station. If the value is disabled(2), port-class traps will not be sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

trapAddrEnable 1.3.6.1.4.1.50.1.2.2.6.1.7
The state of the address-class trap enable for the management station. If the value is disabled(2), address- class traps will not be sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

trapDelete 1.3.6.1.4.1.50.1.2.2.6.1.9
Setting this object to any legal, ASN.1 value deletes the entry for the management station.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER