Nortel-Magellan-Passport-FrameRelayNniMIB

File: Nortel-Magellan-Passport-FrameRelayNniMIB.mib (284904 bytes)

Imported modules

RFC-1212	Nortel-Magellan-Passport-UsefulDefinitionsMIB	Nortel-Magellan-Passport-StandardTextualConventionsMIB
Nortel-Magellan-Passport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE	components	passportMIBs
Counter32	RowPointer	DisplayString
StorageType	RowStatus	PassportCounter64
InterfaceIndex	Gauge32	Integer32
Unsigned32	AsciiString	Hex
NonReplicated	FixedPoint3	HexString
EnterpriseDateAndTime	Link	DigitString
Unsigned64

Defined Types

FrNniRowStatusEntry
SEQUENCE
	frNniRowStatus	RowStatus
	frNniComponentName	DisplayString
	frNniStorageType	StorageType
	frNniIndex	Integer32

FrNniCidDataEntry
SEQUENCE
	frNniCustomerIdentifier	Unsigned32

FrNniStateEntry
SEQUENCE
	frNniAdminState	INTEGER
	frNniOperationalState	INTEGER
	frNniUsageState	INTEGER
	frNniAvailabilityStatus	OCTET STRING
	frNniProceduralStatus	OCTET STRING
	frNniControlStatus	OCTET STRING
	frNniAlarmStatus	OCTET STRING
	frNniStandbyStatus	INTEGER
	frNniUnknownStatus	INTEGER

FrNniStatsEntry
SEQUENCE
	frNniLastUnknownDlci	Unsigned32
	frNniUnknownDlciFramesFromIf	Counter32
	frNniInvalidHeaderFramesFromIf	Counter32

FrNniIfEntryEntry
SEQUENCE
	frNniIfAdminStatus	INTEGER
	frNniIfIndex	InterfaceIndex

FrNniOperStatusEntry
SEQUENCE
	frNniSnmpOperStatus	INTEGER

FrNniEmissionPriorityQsEntry
SEQUENCE
	frNniNumberOfEmissionQs	Unsigned32

FrNniFrmToIfByQueueEntry
SEQUENCE
	frNniFrmToIfByQueueIndex	Integer32
	frNniFrmToIfByQueueValue	Unsigned32

FrNniOctetToIfByQueueEntry
SEQUENCE
	frNniOctetToIfByQueueIndex	Integer32
	frNniOctetToIfByQueueValue	Unsigned32

FrNniDnaRowStatusEntry
SEQUENCE
	frNniDnaRowStatus	RowStatus
	frNniDnaComponentName	DisplayString
	frNniDnaStorageType	StorageType
	frNniDnaIndex	NonReplicated

FrNniDnaAddressEntry
SEQUENCE
	frNniDnaNumberingPlanIndicator	INTEGER
	frNniDnaDataNetworkAddress	DigitString

FrNniDnaOutgoingOptionsEntry
SEQUENCE
	frNniDnaOutDefaultPriority	INTEGER
	frNniDnaOutDefaultPathSensitivity	INTEGER
	frNniDnaOutPathSensitivityOverRide	INTEGER
	frNniDnaOutDefaultPathReliability	INTEGER
	frNniDnaOutAccess	INTEGER
	frNniDnaDefaultTransferPriority	INTEGER
	frNniDnaTransferPriorityOverRide	INTEGER

FrNniDnaIncomingOptionsEntry
SEQUENCE
	frNniDnaIncAccess	INTEGER

FrNniDnaCallOptionsEntry
SEQUENCE
	frNniDnaAccountClass	Unsigned32
	frNniDnaAccountCollection	OCTET STRING
	frNniDnaServiceExchange	Unsigned32
	frNniDnaEgressAccounting	INTEGER
	frNniDnaDataPath	INTEGER

FrNniDnaCugRowStatusEntry
SEQUENCE
	frNniDnaCugRowStatus	RowStatus
	frNniDnaCugComponentName	DisplayString
	frNniDnaCugStorageType	StorageType
	frNniDnaCugIndex	Integer32

FrNniDnaCugCugOptionsEntry
SEQUENCE
	frNniDnaCugType	INTEGER
	frNniDnaCugDnic	DigitString
	frNniDnaCugInterlockCode	Unsigned32
	frNniDnaCugPreferential	INTEGER
	frNniDnaCugOutCalls	INTEGER
	frNniDnaCugIncCalls	INTEGER

FrNniDnaHgMRowStatusEntry
SEQUENCE
	frNniDnaHgMRowStatus	RowStatus
	frNniDnaHgMComponentName	DisplayString
	frNniDnaHgMStorageType	StorageType
	frNniDnaHgMIndex	NonReplicated

FrNniDnaHgMIfEntry
SEQUENCE
	frNniDnaHgMAvailabilityUpdateThreshold	Unsigned32

FrNniDnaHgMOpEntry
SEQUENCE
	frNniDnaHgMMaximumAvailableAggregateCir	Unsigned32
	frNniDnaHgMAvailableAggregateCir	Unsigned32
	frNniDnaHgMAvailabilityDelta	INTEGER
	frNniDnaHgMAvailableDlcis	Unsigned32

FrNniDnaHgMHgAddrRowStatusEntry
SEQUENCE
	frNniDnaHgMHgAddrRowStatus	RowStatus
	frNniDnaHgMHgAddrComponentName	DisplayString
	frNniDnaHgMHgAddrStorageType	StorageType
	frNniDnaHgMHgAddrIndex	Integer32

FrNniDnaHgMHgAddrAddrEntry
SEQUENCE
	frNniDnaHgMHgAddrNumberingPlanIndicator	INTEGER
	frNniDnaHgMHgAddrDataNetworkAddress	DigitString

FrNniFramerRowStatusEntry
SEQUENCE
	frNniFramerRowStatus	RowStatus
	frNniFramerComponentName	DisplayString
	frNniFramerStorageType	StorageType
	frNniFramerIndex	NonReplicated

FrNniFramerProvEntry
SEQUENCE
	frNniFramerInterfaceName	Link

FrNniFramerLinkEntry
SEQUENCE
	frNniFramerFlagsBetweenFrames	Unsigned32

FrNniFramerStateEntry
SEQUENCE
	frNniFramerAdminState	INTEGER
	frNniFramerOperationalState	INTEGER
	frNniFramerUsageState	INTEGER

FrNniFramerStatsEntry
SEQUENCE
	frNniFramerFrmToIf	Counter32
	frNniFramerFrmFromIf	Counter32
	frNniFramerOctetFromIf	Counter32
	frNniFramerAborts	Counter32
	frNniFramerCrcErrors	Counter32
	frNniFramerLrcErrors	Counter32
	frNniFramerNonOctetErrors	Counter32
	frNniFramerOverruns	Counter32
	frNniFramerUnderruns	Counter32
	frNniFramerLargeFrmErrors	Counter32
	frNniFramerFrmModeErrors	Counter32

FrNniFramerUtilEntry
SEQUENCE
	frNniFramerNormPrioLinkUtilToIf	Gauge32
	frNniFramerNormPrioLinkUtilFromIf	Gauge32

FrNniLmiRowStatusEntry
SEQUENCE
	frNniLmiRowStatus	RowStatus
	frNniLmiComponentName	DisplayString
	frNniLmiStorageType	StorageType
	frNniLmiIndex	NonReplicated

FrNniLmiParmsEntry
SEQUENCE
	frNniLmiProcedures	INTEGER
	frNniLmiAsyncStatusReport	INTEGER
	frNniLmiErrorEventThreshold	Unsigned32
	frNniLmiEventCount	Unsigned32
	frNniLmiCheckPointTimer	Unsigned32
	frNniLmiIgnoreActiveBit	INTEGER

FrNniLmiNniParmsEntry
SEQUENCE
	frNniLmiFullStatusPollingCycles	Unsigned32
	frNniLmiLinkVerificationTimer	Unsigned32

FrNniLmiStateEntry
SEQUENCE
	frNniLmiAdminState	INTEGER
	frNniLmiOperationalState	INTEGER
	frNniLmiUsageState	INTEGER

FrNniLmiPsiEntry
SEQUENCE
	frNniLmiProtocolStatus	INTEGER
	frNniLmiOpProcedures	INTEGER

FrNniLmiStatsEntry
SEQUENCE
	frNniLmiKeepAliveStatusToIf	Counter32
	frNniLmiFullStatusToIf	Counter32
	frNniLmiKeepAliveStatusEnqFromIf	Counter32
	frNniLmiFullStatusEnqFromIf	Counter32
	frNniLmiNetworkSideEventHistory	AsciiString
	frNniLmiUserSideEventHistory	AsciiString
	frNniLmiProtocolErrors	Counter32
	frNniLmiUnexpectedIes	Counter32
	frNniLmiSequenceErrors	Counter32
	frNniLmiStatusSequenceErrors	Counter32
	frNniLmiUnexpectedReports	Counter32
	frNniLmiPollingVerifTimeouts	Counter32
	frNniLmiNoStatusReportCount	Counter32

FrNniDlciRowStatusEntry
SEQUENCE
	frNniDlciRowStatus	RowStatus
	frNniDlciComponentName	DisplayString
	frNniDlciStorageType	StorageType
	frNniDlciIndex	Integer32

FrNniDlciStateEntry
SEQUENCE
	frNniDlciAdminState	INTEGER
	frNniDlciOperationalState	INTEGER
	frNniDlciUsageState	INTEGER
	frNniDlciAvailabilityStatus	OCTET STRING
	frNniDlciProceduralStatus	OCTET STRING
	frNniDlciControlStatus	OCTET STRING
	frNniDlciAlarmStatus	OCTET STRING
	frNniDlciStandbyStatus	INTEGER
	frNniDlciUnknownStatus	INTEGER

FrNniDlciAbitEntry
SEQUENCE
	frNniDlciABitStatusToIf	INTEGER
	frNniDlciABitReasonToIf	INTEGER
	frNniDlciABitStatusFromIf	INTEGER
	frNniDlciABitReasonFromIf	INTEGER
	frNniDlciLoopbackState	INTEGER

FrNniDlciSpOpEntry
SEQUENCE
	frNniDlciMaximumFrameSize	Unsigned32
	frNniDlciRateEnforcement	INTEGER
	frNniDlciCommittedInformationRate	Unsigned32
	frNniDlciCommittedBurstSize	Unsigned32
	frNniDlciExcessBurstSize	Unsigned32
	frNniDlciMeasurementInterval	Unsigned32
	frNniDlciRateAdaptation	INTEGER
	frNniDlciAccounting	INTEGER
	frNniDlciEmissionPriorityToIf	INTEGER
	frNniDlciTransferPriToNwk	Unsigned32
	frNniDlciTransferPriFromNwk	Unsigned32

FrNniDlciStatsEntry
SEQUENCE
	frNniDlciFrmToIf	Unsigned32
	frNniDlciFecnFrmToIf	Unsigned32
	frNniDlciBecnFrmToIf	Unsigned32
	frNniDlciBciToSubnet	Unsigned32
	frNniDlciDeFrmToIf	Unsigned32
	frNniDlciDiscCongestedToIf	Unsigned32
	frNniDlciDiscDeCongestedToIf	Unsigned32
	frNniDlciFrmFromIf	Unsigned32
	frNniDlciFecnFrmFromIf	Unsigned32
	frNniDlciBecnFrmFromIf	Unsigned32
	frNniDlciFciFromSubnet	Unsigned32
	frNniDlciBciFromSubnet	Unsigned32
	frNniDlciDeFrmFromIf	Unsigned32
	frNniDlciExcessFrmFromIf	Unsigned32
	frNniDlciDiscExcessFromIf	Unsigned32
	frNniDlciDiscFrameAbit	Unsigned32
	frNniDlciDiscCongestedFromIf	Unsigned32
	frNniDlciDiscDeCongestedFromIf	Unsigned32
	frNniDlciErrorShortFrmFromIf	Unsigned32
	frNniDlciErrorLongFrmFromIf	Unsigned32
	frNniDlciBecnFrmSetByService	Unsigned32
	frNniDlciBytesToIf	Unsigned32
	frNniDlciDeBytesToIf	Unsigned32
	frNniDlciDiscCongestedToIfBytes	Unsigned32
	frNniDlciDiscDeCongestedToIfBytes	Unsigned32
	frNniDlciBytesFromIf	Unsigned32
	frNniDlciDeBytesFromIf	Unsigned32
	frNniDlciExcessBytesFromIf	Unsigned32
	frNniDlciDiscExcessFromIfBytes	Unsigned32
	frNniDlciDiscByteAbit	Unsigned32
	frNniDlciDiscCongestedFromIfBytes	Unsigned32
	frNniDlciDiscDeCongestedFromIfBytes	Unsigned32
	frNniDlciErrorShortBytesFromIf	Unsigned32
	frNniDlciErrorLongBytesFromIf	Unsigned32
	frNniDlciRateAdaptReduct	Unsigned32
	frNniDlciRateAdaptReductPeriod	Unsigned32
	frNniDlciTransferPriorityToNetwork	INTEGER
	frNniDlciTransferPriorityFromNetwork	INTEGER
	frNniDlciCirPresent	Unsigned32
	frNniDlciEirPresent	Unsigned32

FrNniDlciIntEntry
SEQUENCE
	frNniDlciStartTime	EnterpriseDateAndTime
	frNniDlciTotalIngressBytes	Unsigned64
	frNniDlciTotalEgressBytes	Unsigned64
	frNniDlciEirIngressBytes	Unsigned64
	frNniDlciEirEgressBytes	Unsigned64
	frNniDlciDiscardedBytes	Unsigned64
	frNniDlciTotalIngressSegFrm	Unsigned32
	frNniDlciTotalEgressSegFrm	Unsigned32
	frNniDlciEirIngressSegFrm	Unsigned32
	frNniDlciEirEgressSegFrm	Unsigned32
	frNniDlciDiscardedSegFrm	Unsigned32
	frNniDlciCirPresentObs	Unsigned32
	frNniDlciEirPresentObs	Unsigned32
	frNniDlciRateEnforcementPresent	INTEGER
	frNniDlciRateAdaptationPresent	INTEGER
	frNniDlciLocalRateAdaptOccurred	INTEGER
	frNniDlciCallReferenceNumber	Hex
	frNniDlciElapsedDifference	Unsigned32

FrNniDlciDcRowStatusEntry
SEQUENCE
	frNniDlciDcRowStatus	RowStatus
	frNniDlciDcComponentName	DisplayString
	frNniDlciDcStorageType	StorageType
	frNniDlciDcIndex	NonReplicated

FrNniDlciDcOptionsEntry
SEQUENCE
	frNniDlciDcRemoteNpi	INTEGER
	frNniDlciDcRemoteDna	DigitString
	frNniDlciDcRemoteDlci	Unsigned32
	frNniDlciDcType	INTEGER
	frNniDlciDcTransferPriority	INTEGER
	frNniDlciDcDiscardPriority	INTEGER
	frNniDlciDcDeDiscardPriority	INTEGER
	frNniDlciDcDataPath	INTEGER
	frNniDlciDcCugIndex	Unsigned32
	frNniDlciDcCugType	INTEGER

FrNniDlciDcNfaEntry
SEQUENCE
	frNniDlciDcNfaIndex	Integer32
	frNniDlciDcNfaValue	HexString
	frNniDlciDcNfaRowStatus	RowStatus

FrNniDlciVcRowStatusEntry
SEQUENCE
	frNniDlciVcRowStatus	RowStatus
	frNniDlciVcComponentName	DisplayString
	frNniDlciVcStorageType	StorageType
	frNniDlciVcIndex	NonReplicated

FrNniDlciVcCadEntry
SEQUENCE
	frNniDlciVcType	INTEGER
	frNniDlciVcState	INTEGER
	frNniDlciVcPreviousState	INTEGER
	frNniDlciVcDiagnosticCode	Unsigned32
	frNniDlciVcPreviousDiagnosticCode	Unsigned32
	frNniDlciVcCalledNpi	INTEGER
	frNniDlciVcCalledDna	DigitString
	frNniDlciVcCalledLcn	Unsigned32
	frNniDlciVcCallingNpi	INTEGER
	frNniDlciVcCallingDna	DigitString
	frNniDlciVcCallingLcn	Unsigned32
	frNniDlciVcAccountingEnabled	INTEGER
	frNniDlciVcFastSelectCall	INTEGER
	frNniDlciVcPathReliability	INTEGER
	frNniDlciVcAccountingEnd	INTEGER
	frNniDlciVcPriority	INTEGER
	frNniDlciVcSegmentSize	Unsigned32
	frNniDlciVcMaxSubnetPktSize	Unsigned32
	frNniDlciVcRcosToNetwork	INTEGER
	frNniDlciVcRcosFromNetwork	INTEGER
	frNniDlciVcEmissionPriorityToNetwork	INTEGER
	frNniDlciVcEmissionPriorityFromNetwork	INTEGER
	frNniDlciVcDataPath	AsciiString

FrNniDlciVcIntdEntry
SEQUENCE
	frNniDlciVcCallReferenceNumber	Hex
	frNniDlciVcElapsedTimeTillNow	Unsigned32
	frNniDlciVcSegmentsRx	Unsigned32
	frNniDlciVcSegmentsSent	Unsigned32
	frNniDlciVcStartTime	EnterpriseDateAndTime

FrNniDlciVcFrdEntry
SEQUENCE
	frNniDlciVcFrmCongestedToSubnet	Unsigned32
	frNniDlciVcCannotForwardToSubnet	Unsigned32
	frNniDlciVcNotDataXferToSubnet	Unsigned32
	frNniDlciVcOutOfRangeFrmFromSubnet	Unsigned32
	frNniDlciVcCombErrorsFromSubnet	Unsigned32
	frNniDlciVcDuplicatesFromSubnet	Unsigned32
	frNniDlciVcNotDataXferFromSubnet	Unsigned32
	frNniDlciVcFrmLossTimeouts	Unsigned32
	frNniDlciVcOoSeqByteCntExceeded	Unsigned32
	frNniDlciVcPeakOoSeqPktCount	Unsigned32
	frNniDlciVcPeakOoSeqFrmForwarded	Unsigned32
	frNniDlciVcSendSequenceNumber	Unsigned32
	frNniDlciVcPktRetryTimeouts	Unsigned32
	frNniDlciVcPeakRetryQueueSize	Unsigned32
	frNniDlciVcSubnetRecoveries	Unsigned32
	frNniDlciVcOoSeqPktCntExceeded	Unsigned32
	frNniDlciVcPeakOoSeqByteCount	Unsigned32

FrNniDlciVcDmepEntry
SEQUENCE
	frNniDlciVcDmepValue	RowPointer

FrNniDlciSpRowStatusEntry
SEQUENCE
	frNniDlciSpRowStatus	RowStatus
	frNniDlciSpComponentName	DisplayString
	frNniDlciSpStorageType	StorageType
	frNniDlciSpIndex	NonReplicated

FrNniDlciSpParmsEntry
SEQUENCE
	frNniDlciSpMaximumFrameSize	Unsigned32
	frNniDlciSpRateEnforcement	INTEGER
	frNniDlciSpCommittedInformationRate	Gauge32
	frNniDlciSpCommittedBurstSize	Gauge32
	frNniDlciSpExcessBurstSize	Gauge32
	frNniDlciSpMeasurementInterval	Unsigned32
	frNniDlciSpRateAdaptation	INTEGER
	frNniDlciSpAccounting	INTEGER
	frNniDlciSpRaSensitivity	Unsigned32
	frNniDlciSpUpdateBCI	INTEGER

FrNniDlciLbRowStatusEntry
SEQUENCE
	frNniDlciLbRowStatus	RowStatus
	frNniDlciLbComponentName	DisplayString
	frNniDlciLbStorageType	StorageType
	frNniDlciLbIndex	NonReplicated

FrNniDlciLbStatsEntry
SEQUENCE
	frNniDlciLbLocalTotalFrm	Unsigned32
	frNniDlciLbLocalTotalBytes	Unsigned32
	frNniDlciLbLocalFecnFrm	Unsigned32
	frNniDlciLbLocalBecnFrm	Unsigned32
	frNniDlciLbLocalDeFrm	Unsigned32
	frNniDlciLbLocalDeBytes	Unsigned32
	frNniDlciLbRemoteTotalFrm	Unsigned32
	frNniDlciLbRemoteTotalBytes	Unsigned32
	frNniDlciLbRemoteFecnFrm	Unsigned32
	frNniDlciLbRemoteBecnFrm	Unsigned32
	frNniDlciLbRemoteDeFrm	Unsigned32
	frNniDlciLbRemoteDeBytes	Unsigned32

FrNniVFramerRowStatusEntry
SEQUENCE
	frNniVFramerRowStatus	RowStatus
	frNniVFramerComponentName	DisplayString
	frNniVFramerStorageType	StorageType
	frNniVFramerIndex	NonReplicated

FrNniVFramerProvEntry
SEQUENCE
	frNniVFramerOtherVirtualFramer	Link
	frNniVFramerLogicalProcessor	Link

FrNniVFramerStateEntry
SEQUENCE
	frNniVFramerAdminState	INTEGER
	frNniVFramerOperationalState	INTEGER
	frNniVFramerUsageState	INTEGER

FrNniVFramerStatsEntry
SEQUENCE
	frNniVFramerFrmToOtherVFramer	PassportCounter64
	frNniVFramerFrmFromOtherVFramer	PassportCounter64
	frNniVFramerOctetFromOtherVFramer	PassportCounter64

FrNniLtsRowStatusEntry
SEQUENCE
	frNniLtsRowStatus	RowStatus
	frNniLtsComponentName	DisplayString
	frNniLtsStorageType	StorageType
	frNniLtsIndex	NonReplicated

FrNniLtsSetupEntry
SEQUENCE
	frNniLtsDuration	Unsigned32
	frNniLtsAlgorithm	INTEGER
	frNniLtsBurstSize	Unsigned32
	frNniLtsTimeInterval	Unsigned32

FrNniLtsStateEntry
SEQUENCE
	frNniLtsGeneratorState	INTEGER
	frNniLtsCycleIncomplete	INTEGER
	frNniLtsLastActiveInterval	Unsigned32
	frNniLtsLoad	FixedPoint3
	frNniLtsElapsedGenerationTime	Unsigned32

FrNniLtsResultsEntry
SEQUENCE
	frNniLtsFramesTx	Counter32
	frNniLtsBytesTx	Unsigned32
	frNniLtsBitRateTx	FixedPoint3
	frNniLtsFrameRateTx	Unsigned32

FrNniLtsPatRowStatusEntry
SEQUENCE
	frNniLtsPatRowStatus	RowStatus
	frNniLtsPatComponentName	DisplayString
	frNniLtsPatStorageType	StorageType
	frNniLtsPatIndex	Integer32

FrNniLtsPatDefaultsEntry
SEQUENCE
	frNniLtsPatDefaultDlci	Unsigned32
	frNniLtsPatDefaultNumFrames	Unsigned32
	frNniLtsPatDefaultDataSize	Unsigned32
	frNniLtsPatDefaultHeaderBits	OCTET STRING
	frNniLtsPatDefaultHeaderLength	Unsigned32
	frNniLtsPatDefaultEABits	Hex
	frNniLtsPatDefaultPayloadPattern	HexString
	frNniLtsPatDefaultRfc1490Header	INTEGER
	frNniLtsPatDefaultUseBadLrc	INTEGER

FrNniLtsPatSetupEntry
SEQUENCE
	frNniLtsPatDlci	Unsigned32
	frNniLtsPatNumFrames	Unsigned32
	frNniLtsPatDataSize	Unsigned32
	frNniLtsPatHeaderBits	OCTET STRING
	frNniLtsPatHeaderLength	Unsigned32
	frNniLtsPatEaBits	Hex
	frNniLtsPatPayloadPattern	HexString
	frNniLtsPatRfc1490Header	INTEGER
	frNniLtsPatUseBadLrc	INTEGER

FrNniLtsPatOpDataEntry
SEQUENCE
	frNniLtsPatFramePattern	HexString
	frNniLtsPatHdlcBitsInserted	Unsigned32

FrNniLtsPatOpStateEntry
SEQUENCE
	frNniLtsPatLoad	FixedPoint3
	frNniLtsPatStatus	INTEGER

Defined Values

frameRelayNniMIB		1.3.6.1.4.1.562.2.4.2.23
OBJECT IDENTIFIER

frNni		1.3.6.1.4.1.562.2.4.1.70
OBJECT IDENTIFIER

frNniRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.1
This entry controls the addition and deletion of frNni components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniRowStatusEntry

frNniRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.1.1
A single entry in the table represents a single frNni component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniRowStatusEntry

frNniRowStatus		1.3.6.1.4.1.562.2.4.1.70.1.1.1
This variable is used as the basis for SNMP naming of frNni components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniComponentName		1.3.6.1.4.1.562.2.4.1.70.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniStorageType		1.3.6.1.4.1.562.2.4.1.70.1.1.4
This variable represents the storage type value for the frNni tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniIndex		1.3.6.1.4.1.562.2.4.1.70.1.1.10
This variable represents the index for the frNni tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

frNniCidDataTable		1.3.6.1.4.1.562.2.4.1.70.10
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniCidDataEntry

frNniCidDataEntry		1.3.6.1.4.1.562.2.4.1.70.10.1
An entry in the frNniCidDataTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniCidDataEntry

frNniCustomerIdentifier		1.3.6.1.4.1.562.2.4.1.70.10.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0 | 1..8191

frNniStateTable		1.3.6.1.4.1.562.2.4.1.70.11
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniStateEntry

frNniStateEntry		1.3.6.1.4.1.562.2.4.1.70.11.1
An entry in the frNniStateTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniStateEntry

frNniAdminState		1.3.6.1.4.1.562.2.4.1.70.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	locked(0), unlocked(1), shuttingDown(2)

frNniOperationalState		1.3.6.1.4.1.562.2.4.1.70.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

frNniUsageState		1.3.6.1.4.1.562.2.4.1.70.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(0), active(1), busy(2)

frNniAvailabilityStatus		1.3.6.1.4.1.562.2.4.1.70.11.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

frNniProceduralStatus		1.3.6.1.4.1.562.2.4.1.70.11.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniControlStatus		1.3.6.1.4.1.562.2.4.1.70.11.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniAlarmStatus		1.3.6.1.4.1.562.2.4.1.70.11.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniStandbyStatus		1.3.6.1.4.1.562.2.4.1.70.11.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hotStandby(0), coldStandby(1), providingService(2), notSet(15)

frNniUnknownStatus		1.3.6.1.4.1.562.2.4.1.70.11.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	false(0), true(1)

frNniStatsTable		1.3.6.1.4.1.562.2.4.1.70.12
FrNni/n Statistics This group contains the statistics about the operational behavior of the service at the interface level.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniStatsEntry

frNniStatsEntry		1.3.6.1.4.1.562.2.4.1.70.12.1
An entry in the frNniStatsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniStatsEntry

frNniLastUnknownDlci		1.3.6.1.4.1.562.2.4.1.70.12.1.1
This attribute identifies the most recent DLCI which user frames were received on for which a DLCI has not been provisioned on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..1023

frNniUnknownDlciFramesFromIf		1.3.6.1.4.1.562.2.4.1.70.12.1.2
This attribute contains a count of the number of frames received from the interface with an unknown DLCI (DLCI which is not provisioned). When the maximum is reached the count wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniInvalidHeaderFramesFromIf		1.3.6.1.4.1.562.2.4.1.70.12.1.3
This attribute counts the number of frames received from the interface with an invalid header format. When the maximum is reached the count wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniIfEntryTable		1.3.6.1.4.1.562.2.4.1.70.13
This group contains the provisionable attributes for the ifEntry.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniIfEntryEntry

frNniIfEntryEntry		1.3.6.1.4.1.562.2.4.1.70.13.1
An entry in the frNniIfEntryTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniIfEntryEntry

frNniIfAdminStatus		1.3.6.1.4.1.562.2.4.1.70.13.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

frNniIfIndex		1.3.6.1.4.1.562.2.4.1.70.13.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
Status: mandatory	Access: read-only
OBJECT-TYPE
	InterfaceIndex	1..65535

frNniOperStatusTable		1.3.6.1.4.1.562.2.4.1.70.14
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniOperStatusEntry

frNniOperStatusEntry		1.3.6.1.4.1.562.2.4.1.70.14.1
An entry in the frNniOperStatusTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniOperStatusEntry

frNniSnmpOperStatus		1.3.6.1.4.1.562.2.4.1.70.14.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

frNniEmissionPriorityQsTable		1.3.6.1.4.1.562.2.4.1.70.15
This group contains the provisionable attribute to specifie the number of Frame Relay egress emission priority queues to be used on that Frame Relay Interface
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniEmissionPriorityQsEntry

frNniEmissionPriorityQsEntry		1.3.6.1.4.1.562.2.4.1.70.15.1
An entry in the frNniEmissionPriorityQsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniEmissionPriorityQsEntry

frNniNumberOfEmissionQs		1.3.6.1.4.1.562.2.4.1.70.15.1.1
This attribute specifies the number of egress emission priority queues that will be used for that Frame Relay interface. The possible values of this attribute are 2 or 4: For V.35, V.11, HSSI, E1, DS1, E3, DS3 or 8pDS1 the possible values are: 2 (in which case they are hardware queues), or 4 (in which case they are software queues). For DS1C, E1C or DS3C the possible values are 2, 4 (in all cases they are software queues).
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	2 | 4

frNniFrmToIfByQueueTable		1.3.6.1.4.1.562.2.4.1.70.341
This attribute counts the total number of frames transmitted to the interface per egress emission priority queue since the component has been activated. There is potientially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority. The queue values are only indicated when the numberOfEmissionQs is set to 4 queues.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniFrmToIfByQueueEntry

frNniFrmToIfByQueueEntry		1.3.6.1.4.1.562.2.4.1.70.341.1
An entry in the frNniFrmToIfByQueueTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniFrmToIfByQueueEntry

frNniFrmToIfByQueueIndex		1.3.6.1.4.1.562.2.4.1.70.341.1.1
This variable represents the index for the frNniFrmToIfByQueueTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	0..3

frNniFrmToIfByQueueValue		1.3.6.1.4.1.562.2.4.1.70.341.1.2
This variable represents an individual value for the frNniFrmToIfByQueueTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniOctetToIfByQueueTable		1.3.6.1.4.1.562.2.4.1.70.342
This attribute counts the total number of octets transmitted from the service to the interface per emission priority queue since the component has been activated. There is potientially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniOctetToIfByQueueEntry

frNniOctetToIfByQueueEntry		1.3.6.1.4.1.562.2.4.1.70.342.1
An entry in the frNniOctetToIfByQueueTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniOctetToIfByQueueEntry

frNniOctetToIfByQueueIndex		1.3.6.1.4.1.562.2.4.1.70.342.1.1
This variable represents the index for the frNniOctetToIfByQueueTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	0..3

frNniOctetToIfByQueueValue		1.3.6.1.4.1.562.2.4.1.70.342.1.2
This variable represents an individual value for the frNniOctetToIfByQueueTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDna		1.3.6.1.4.1.562.2.4.1.70.2
OBJECT IDENTIFIER

frNniDnaRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.2.1
This entry controls the addition and deletion of frNniDna components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaRowStatusEntry

frNniDnaRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.2.1.1
A single entry in the table represents a single frNniDna component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaRowStatusEntry

frNniDnaRowStatus		1.3.6.1.4.1.562.2.4.1.70.2.1.1.1
This variable is used as the basis for SNMP naming of frNniDna components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

frNniDnaComponentName		1.3.6.1.4.1.562.2.4.1.70.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDnaStorageType		1.3.6.1.4.1.562.2.4.1.70.2.1.1.4
This variable represents the storage type value for the frNniDna tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDnaIndex		1.3.6.1.4.1.562.2.4.1.70.2.1.1.10
This variable represents the index for the frNniDna tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniDnaAddressTable		1.3.6.1.4.1.562.2.4.1.70.2.10
This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaAddressEntry

frNniDnaAddressEntry		1.3.6.1.4.1.562.2.4.1.70.2.10.1
An entry in the frNniDnaAddressTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaAddressEntry

frNniDnaNumberingPlanIndicator		1.3.6.1.4.1.562.2.4.1.70.2.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the DNA that is entered. Address may belong to X.121 or E.164 plans. X.121 is used in packet switched data networks.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

frNniDnaDataNetworkAddress		1.3.6.1.4.1.562.2.4.1.70.2.10.1.2
This attribute indicates the customer's unique identifier. It is the equivalent of the telephone number in the telephone network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DigitString	Size(1..15)

frNniDnaOutgoingOptionsTable		1.3.6.1.4.1.562.2.4.1.70.2.11
This group defines DNA call options for calls made from the interface. These options are not used for calls arriving to the interface represented by this DNA.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaOutgoingOptionsEntry

frNniDnaOutgoingOptionsEntry		1.3.6.1.4.1.562.2.4.1.70.2.11.1
An entry in the frNniDnaOutgoingOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaOutgoingOptionsEntry

frNniDnaOutDefaultPriority		1.3.6.1.4.1.562.2.4.1.70.2.11.1.7
This attribute indicates the default priority of outgoing calls from the DTE to the network. It can be overridden by the discardPriority under DLCI Direct Call subcomponent. This option can be also included in X.25 signalling, in such case it will be overruled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(0), high(1)

frNniDnaOutDefaultPathSensitivity		1.3.6.1.4.1.562.2.4.1.70.2.11.1.11
This attribute specifies the default class of path sensitivity to network for all outgoing calls that use this DNA. The chosen default class of path sensitivity applies to all outgoing calls established using this DNA. This attribute, if set to throughput, indicates that the default class is throughput sensitive. If set to delay, then the default class is delay sensitive. The default of outDefaultPathSensitivity is throughput.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	throughput(0), delay(1)

frNniDnaOutPathSensitivityOverRide		1.3.6.1.4.1.562.2.4.1.70.2.11.1.12
If this attribute is set to yes in the call request, the called end will use the calling end provisioning data on path sensitivity to override its own provisioning data. The default of outPathSensitivityOverRide is yes.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniDnaOutDefaultPathReliability		1.3.6.1.4.1.562.2.4.1.70.2.11.1.14
This attribute specifies the default class of routing for reliability routing for all outgoing calls (from the DTE to the network) using this particular DNA. The chosen default class of routing applies to all outgoing calls established using this DNA, and applies to the packets travelling in both directions on all outgoing calls (local to remote, and remote to local). For incoming calls, the default class of routing is chosen by the calling party (as opposed to DPN, where either end of the call can choose the default routing class). This attribute, if set to a value of normal, indicates that the default class of routing is normal reliability routing. If set to a value of high, then the default class of routing is high reliability routing. High reliability is the standard choice for most DPN and Passport services. It usually indicates that packets are overflowed or retransmitted at various routing levels. Typically high reliability results in duplication and disordering of packets in the network when errors are detected or during link congestion. However, the VC handles the duplication and disordering to ensure that packets are delivered to the DTE properly. For the Frame Relay service, duplication of packets is not desired, in which case, normal reliability may be chosen as the preferred class of routing.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	high(0), normal(1)

frNniDnaOutAccess		1.3.6.1.4.1.562.2.4.1.70.2.11.1.17
This attribute is an extension of the Closed User Group (CUG) facility, as follows: This attribute, if set to a value of allowed indicates that outgoing calls (from the DTE to the network) to the open (non-CUG) part of the network are permitted. It also permits outgoing calls to DTEs that have Incoming Access capabilities. If set to a value of disallowed, then such calls cannot be made using this DNA. Such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Outgoing Access' feature for DNAs in that outgoing access is granted if this attribute is set to a value of allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disallowed(0), allowed(1)

frNniDnaDefaultTransferPriority		1.3.6.1.4.1.562.2.4.1.70.2.11.1.18
This attribute specifies the default transfer priority for all outgoing calls using this particular DNA. It can be overridden by the transferPriority provisioned in the Dlci DirectCall sub-component. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n indicates the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required. The default defaultTransferPriority is 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)

frNniDnaTransferPriorityOverRide		1.3.6.1.4.1.562.2.4.1.70.2.11.1.19
When this attribute is set to yes in the call request, the called end will use the calling end provisioning data on transfer priority to override its own provisioning data. If it is set no, the called end will use its own provisioning data on transfer priority. This attribute is not applicable for Frame Relay SVCs. For more information about transfer priority, please refer to the previous attribute defaultTransferPriority. The default of transferPriorityOverRide is yes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniDnaIncomingOptionsTable		1.3.6.1.4.1.562.2.4.1.70.2.12
This group defines options for incoming calls. These options are used for calls arriving to the interface represented by this DNA. For calls originated from the interface, IncomingOptions attributes are not used.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaIncomingOptionsEntry

frNniDnaIncomingOptionsEntry		1.3.6.1.4.1.562.2.4.1.70.2.12.1
An entry in the frNniDnaIncomingOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaIncomingOptionsEntry

frNniDnaIncAccess		1.3.6.1.4.1.562.2.4.1.70.2.12.1.9
This attribute, if set to a value of allowed specifies that incoming calls (from the network to the DTE) from the open (non-CUG) part of the network are permitted. It also permits incoming calls from DTEs that have outgoing access capabilities. If set to a value of disallowed, such calls cannot be made to this DNA. They will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Incoming Access' feature for DNAs in that incoming access is granted if this attribute is set to a value of allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disallowed(0), allowed(1)

frNniDnaCallOptionsTable		1.3.6.1.4.1.562.2.4.1.70.2.13
This group defines additional all options for not related to direction of the call.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaCallOptionsEntry

frNniDnaCallOptionsEntry		1.3.6.1.4.1.562.2.4.1.70.2.13.1
An entry in the frNniDnaCallOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaCallOptionsEntry

frNniDnaAccountClass		1.3.6.1.4.1.562.2.4.1.70.2.13.1.10
This attribute specifies the accounting class which is reserved for network operations usage. Its value is returned in the accounting record in the local and remote service type attributes. Use of this attribute is decided by network operator. This attribute is returned by the local VC in the accounting record for all calls that are set up using this particular DNA.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

frNniDnaAccountCollection		1.3.6.1.4.1.562.2.4.1.70.2.13.1.11
This attribute indicates that accounting records are to be collected by the network for the various reasons: billing, test, study, auditing. The last of the parameters, force, indicates that accounting records are to be collected irrespective of other collection reasons. The force option is available for X.75 Gateways only. If none of these reasons are set, then accounting will be suppressed. To set a specific accounting collection reason, the reason is entered and the corresponding bit in the structure is set to a value of 1. To turn off a specific accounting collection reason, the reason is entered preceded with the '~' character, and the corresponding bit in the structure is set to a value of 0. The bit placement for the accounting collection reasons is as follows: Bit 0 - Bill Bit 1 - Test Bit 2 - Study Bit 3 - Audit Bit 4 - Force Description of bits: bill(0) test(1) study(2) audit(3) force(4)
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniDnaServiceExchange		1.3.6.1.4.1.562.2.4.1.70.2.13.1.12
This attribute is an arbitrary number, Data Service Exchange, as entered by the network operator and reported in accounting record. It is converted into an internal 8-bit integer value for use in the accounting record as well as in various X.25 and X.75 Tariff utilities.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

frNniDnaEgressAccounting		1.3.6.1.4.1.562.2.4.1.70.2.13.1.13
This attribute specifies if egress accounting is enabled by the frame relay service. If egress accounting is disabled, only segment counts are collected by the VC. No frame relay counts appear in the accounting records for the frame relay service. If egress accounting is enabled, the accounting records for the frame relay service will contain frame relay specific counts.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniDnaDataPath		1.3.6.1.4.1.562.2.4.1.70.2.13.1.21
This attribute specifies the data path to be used by Virtual Circuits on this interface. If the connection has a DirectCall component then the value can be overridden by the dataPath attribute of the DirectCall component. This value applies to the connection after data transfer state is reached. All the data and control trafic will be sent using this data path. If the provisioned dataPath is not available the connection is not established. The value of the dataPath is signalled by both ends of the connection. If this value is not the same at both ends dprsOnly is used for the duration of the connection. A virtual circuit connection is always established using dprsOnly even if this attribute is provisioned as some other value. dprsOnly - dynamic packet routing system is used dprsMcsOnly - dprs Multi-Service Cut-Through Switching path is used. dprsMcsFirst - dprs Multi-Service Cut-Through Switching path is used if it is available. If it is not avaliable dprsOnly is used.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dprsOnly(0), dprsMcsOnly(1), dprsMcsFirst(2)

frNniDnaCug		1.3.6.1.4.1.562.2.4.1.70.2.2
OBJECT IDENTIFIER

frNniDnaCugRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.2.2.1
This entry controls the addition and deletion of frNniDnaCug components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaCugRowStatusEntry

frNniDnaCugRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.2.2.1.1
A single entry in the table represents a single frNniDnaCug component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaCugRowStatusEntry

frNniDnaCugRowStatus		1.3.6.1.4.1.562.2.4.1.70.2.2.1.1.1
This variable is used as the basis for SNMP naming of frNniDnaCug components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniDnaCugComponentName		1.3.6.1.4.1.562.2.4.1.70.2.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDnaCugStorageType		1.3.6.1.4.1.562.2.4.1.70.2.2.1.1.4
This variable represents the storage type value for the frNniDnaCug tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDnaCugIndex		1.3.6.1.4.1.562.2.4.1.70.2.2.1.1.10
This variable represents the index for the frNniDnaCug tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

frNniDnaCugCugOptionsTable		1.3.6.1.4.1.562.2.4.1.70.2.2.10
Attributes in this group define ClosedUserGroup options associated with interlockCode. DNA's with the same CUG (interlockCode) can make calls within this group. Various combinations which permit or prevent calls in the same CUG group are defined here.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaCugCugOptionsEntry

frNniDnaCugCugOptionsEntry		1.3.6.1.4.1.562.2.4.1.70.2.2.10.1
An entry in the frNniDnaCugCugOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaCugCugOptionsEntry

frNniDnaCugType		1.3.6.1.4.1.562.2.4.1.70.2.2.10.1.1
This attribute specifies the CUG type - the CUG is either a national CUG, or an international CUG. International closed user groups are usually established between DTEs for which there is an X.75 Gateway between; whereas national closed user groups are usually established between DTEs for which there is no X.75 Gateway between. (National CUGs cannot normally traverse an X.75 Gateway). If this attribute is set to national, then the CUG is a national CUG, in which case, the dnic should be left at its default value since it is not part of a national CUG. If this attribute is set to international, then the CUG is an international CUG, in which case, the dnic should be set appropriately as part of the CUG interlockCode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	national(0), international(1)

frNniDnaCugDnic		1.3.6.1.4.1.562.2.4.1.70.2.2.10.1.2
This attribute specifies the dnic (Data Network ID Code) of the CUG by which packet networks are identified. This attribute is not applicable if the CUG is a national CUG, as specified by the CUG type attribute. There are usually 1 or 2 dnics assigned per country, for public networks. The U.S. is an exception where each BOC has a dnic. Also, a group of private networks can have its own dnic. dnic value is not an arbitrary number. It is assigned by international agreement and controlled by CCITT.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DigitString	Size(4)

frNniDnaCugInterlockCode		1.3.6.1.4.1.562.2.4.1.70.2.2.10.1.3
This attribute specifies the CUG identifier of a national or international CUG call. It is an arbitrary number and it also can be called CUG in some descriptions. Interfaces (DNA's) defined with this number can make calls to DNA's with the same interlockCode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..65535

frNniDnaCugPreferential		1.3.6.1.4.1.562.2.4.1.70.2.2.10.1.4
The attribute 'preferential', if set to yes indicates that this CUG is the SIMPLE CUG (as defined in ITU X.36 [10/96]), in which case it will be used during the call establishment phase if the DTE has not explicitly specified a CUG index in the call request packet. If set to no, then this CUG is not the SIMPLE CUG, but an instance of the SELECTABLE CUG. The attribute 'preferential' is set to no by CAS when a CUG instance is created. If only one CUG instance exists under a DNA, and if this CUG's attributes 'incCalls' and 'outCall' are both set to allowed, then this CUG instance can be changed to a SIMPLE CUG by setting the attribute 'preferential' to yes. If more than one CUG instances exist under a DNA, none of the CUGs can be set by the user as 'preferential'. Essentially, the attribute 'preferential' distinguishes a SIMPLE CUG from a SELECTABLE CUG. In the case of a FRUNI DNA with a single CUG instance, the CUG can be a SIMPLE CUG (preferential = yes) or the only instance of a SELECTABLE CUG (preferential = no).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniDnaCugOutCalls		1.3.6.1.4.1.562.2.4.1.70.2.2.10.1.5
This attribute, if set to allowed indicates that outgoing calls (from the DTE into the network) can be made using this particular CUG. If set to a value of disallowed, then outgoing calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Outgoing Calls Barred' feature for CUGs in that outgoing calls are barred if this attribute is set to a value of disallowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disallowed(0), allowed(1)

frNniDnaCugIncCalls		1.3.6.1.4.1.562.2.4.1.70.2.2.10.1.6
This attribute, if set to allowed indicates that incoming calls (from the network to the DTE) can be made using this particular CUG. If set to disallowed, then incoming calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Incoming Calls Barred' feature for CUGs in that incoming calls are barred if this attribute is set to a value of disallowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disallowed(0), allowed(1)

frNniDnaHgM		1.3.6.1.4.1.562.2.4.1.70.2.3
OBJECT IDENTIFIER

frNniDnaHgMRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.2.3.1
This entry controls the addition and deletion of frNniDnaHgM components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaHgMRowStatusEntry

frNniDnaHgMRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.2.3.1.1
A single entry in the table represents a single frNniDnaHgM component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaHgMRowStatusEntry

frNniDnaHgMRowStatus		1.3.6.1.4.1.562.2.4.1.70.2.3.1.1.1
This variable is used as the basis for SNMP naming of frNniDnaHgM components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniDnaHgMComponentName		1.3.6.1.4.1.562.2.4.1.70.2.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDnaHgMStorageType		1.3.6.1.4.1.562.2.4.1.70.2.3.1.1.4
This variable represents the storage type value for the frNniDnaHgM tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDnaHgMIndex		1.3.6.1.4.1.562.2.4.1.70.2.3.1.1.10
This variable represents the index for the frNniDnaHgM tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniDnaHgMIfTable		1.3.6.1.4.1.562.2.4.1.70.2.3.10
This group contains the interface parameters between the HuntGroupMember and the hunt group server.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaHgMIfEntry

frNniDnaHgMIfEntry		1.3.6.1.4.1.562.2.4.1.70.2.3.10.1
An entry in the frNniDnaHgMIfTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaHgMIfEntry

frNniDnaHgMAvailabilityUpdateThreshold		1.3.6.1.4.1.562.2.4.1.70.2.3.10.1.1
This attribute specifies how much availableAggregateCIR can change before an Availability Message Packet (AMP) is sent to the hunt group server informing it of the change. If the value specified is not a multiple of 2048, the value actually used as the threshold will be the next higher multiple of 2048.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	2048..16777216

frNniDnaHgMOpTable		1.3.6.1.4.1.562.2.4.1.70.2.3.11
This group contains the operational attributes of the HuntGroupMember component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaHgMOpEntry

frNniDnaHgMOpEntry		1.3.6.1.4.1.562.2.4.1.70.2.3.11.1
An entry in the frNniDnaHgMOpTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaHgMOpEntry

frNniDnaHgMMaximumAvailableAggregateCir		1.3.6.1.4.1.562.2.4.1.70.2.3.11.1.1
This attribute indicates the maximum aggregate CIR availability for this hunt group member. It is the sum of the maximum CIRs provisioned for SVCs in the FrUni Signaling component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDnaHgMAvailableAggregateCir		1.3.6.1.4.1.562.2.4.1.70.2.3.11.1.2
This attribute indicates the current available aggregate CIR reported to the hunt group in the Availability Message Packet (AMP). It is incremented by the application when a DLCI is freed. It is decremented when a DLCI is allocated. The value is the sum of the currently available aggregate CIRs for SVCs. Both this attribute and the availableDlcis attribute must be non zero for this DNA to receive calls on the hunt group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDnaHgMAvailabilityDelta		1.3.6.1.4.1.562.2.4.1.70.2.3.11.1.3
This attribute indicates the net change in the available aggregate CIR since the last Availability Message Packet (AMP) was sent to the Hunt Group. Once the absolute value of this attribute reaches the availabilityUpdateThreshold an AMP is sent to the hunt group server(s) and the availabilityDelta is re-computed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	-16777216..16777215

frNniDnaHgMAvailableDlcis		1.3.6.1.4.1.562.2.4.1.70.2.3.11.1.5
This attribute indicates the number of DLCIs available for SVCs on the interface associated with this DNA. If this value reaches 0, an AMP with zero availability is sent to the hunt group server(s). Both this attribute and the availableAggregateCir attribute must be non zero for this DNA to receive calls on the hunt group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4096

frNniDnaHgMHgAddr		1.3.6.1.4.1.562.2.4.1.70.2.3.2
OBJECT IDENTIFIER

frNniDnaHgMHgAddrRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.2.3.2.1
This entry controls the addition and deletion of frNniDnaHgMHgAddr components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaHgMHgAddrRowStatusEntry

frNniDnaHgMHgAddrRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.2.3.2.1.1
A single entry in the table represents a single frNniDnaHgMHgAddr component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaHgMHgAddrRowStatusEntry

frNniDnaHgMHgAddrRowStatus		1.3.6.1.4.1.562.2.4.1.70.2.3.2.1.1.1
This variable is used as the basis for SNMP naming of frNniDnaHgMHgAddr components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniDnaHgMHgAddrComponentName		1.3.6.1.4.1.562.2.4.1.70.2.3.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDnaHgMHgAddrStorageType		1.3.6.1.4.1.562.2.4.1.70.2.3.2.1.1.4
This variable represents the storage type value for the frNniDnaHgMHgAddr tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDnaHgMHgAddrIndex		1.3.6.1.4.1.562.2.4.1.70.2.3.2.1.1.10
This variable represents the index for the frNniDnaHgMHgAddr tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	0..1

frNniDnaHgMHgAddrAddrTable		1.3.6.1.4.1.562.2.4.1.70.2.3.2.10
This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDnaHgMHgAddrAddrEntry

frNniDnaHgMHgAddrAddrEntry		1.3.6.1.4.1.562.2.4.1.70.2.3.2.10.1
An entry in the frNniDnaHgMHgAddrAddrTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDnaHgMHgAddrAddrEntry

frNniDnaHgMHgAddrNumberingPlanIndicator		1.3.6.1.4.1.562.2.4.1.70.2.3.2.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the DNA. The address may belong to X.121 or E.164 plans.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

frNniDnaHgMHgAddrDataNetworkAddress		1.3.6.1.4.1.562.2.4.1.70.2.3.2.10.1.2
This attribute contains digits which form the unique identifier of the customer interface. It can be compared (approximation only) to a telephone number where the phone number identifies a unique telephone set. DNA digits are selected and assigned by network operators.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DigitString	Size(1..15)

frNniFramer		1.3.6.1.4.1.562.2.4.1.70.3
OBJECT IDENTIFIER

frNniFramerRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.3.1
This entry controls the addition and deletion of frNniFramer components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniFramerRowStatusEntry

frNniFramerRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.3.1.1
A single entry in the table represents a single frNniFramer component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniFramerRowStatusEntry

frNniFramerRowStatus		1.3.6.1.4.1.562.2.4.1.70.3.1.1.1
This variable is used as the basis for SNMP naming of frNniFramer components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniFramerComponentName		1.3.6.1.4.1.562.2.4.1.70.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniFramerStorageType		1.3.6.1.4.1.562.2.4.1.70.3.1.1.4
This variable represents the storage type value for the frNniFramer tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniFramerIndex		1.3.6.1.4.1.562.2.4.1.70.3.1.1.10
This variable represents the index for the frNniFramer tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniFramerProvTable		1.3.6.1.4.1.562.2.4.1.70.3.10
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniFramerProvEntry

frNniFramerProvEntry		1.3.6.1.4.1.562.2.4.1.70.3.10.1
An entry in the frNniFramerProvTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniFramerProvEntry

frNniFramerInterfaceName		1.3.6.1.4.1.562.2.4.1.70.3.10.1.1
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Link

frNniFramerLinkTable		1.3.6.1.4.1.562.2.4.1.70.3.11
This group contains attributes defining the framing of data on the link interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniFramerLinkEntry

frNniFramerLinkEntry		1.3.6.1.4.1.562.2.4.1.70.3.11.1
An entry in the frNniFramerLinkTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniFramerLinkEntry

frNniFramerFlagsBetweenFrames		1.3.6.1.4.1.562.2.4.1.70.3.11.1.4
This attribute defines the number of flags that are inserted between frames sent to the link interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	1..16

frNniFramerStateTable		1.3.6.1.4.1.562.2.4.1.70.3.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniFramerStateEntry

frNniFramerStateEntry		1.3.6.1.4.1.562.2.4.1.70.3.12.1
An entry in the frNniFramerStateTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniFramerStateEntry

frNniFramerAdminState		1.3.6.1.4.1.562.2.4.1.70.3.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	locked(0), unlocked(1), shuttingDown(2)

frNniFramerOperationalState		1.3.6.1.4.1.562.2.4.1.70.3.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

frNniFramerUsageState		1.3.6.1.4.1.562.2.4.1.70.3.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(0), active(1), busy(2)

frNniFramerStatsTable		1.3.6.1.4.1.562.2.4.1.70.3.13
This group contains the operational statistics data for a Framer component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniFramerStatsEntry

frNniFramerStatsEntry		1.3.6.1.4.1.562.2.4.1.70.3.13.1
An entry in the frNniFramerStatsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniFramerStatsEntry

frNniFramerFrmToIf		1.3.6.1.4.1.562.2.4.1.70.3.13.1.1
The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerFrmFromIf		1.3.6.1.4.1.562.2.4.1.70.3.13.1.2
The number of frames received from the link interface by Framer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerOctetFromIf		1.3.6.1.4.1.562.2.4.1.70.3.13.1.3
The number of bytes received from the link interface by Framer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerAborts		1.3.6.1.4.1.562.2.4.1.70.3.13.1.4
This attribute is the total number of aborts received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerCrcErrors		1.3.6.1.4.1.562.2.4.1.70.3.13.1.5
This attribute is the total number of frames with CRC errors, occurring in the receive direction from the link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerLrcErrors		1.3.6.1.4.1.562.2.4.1.70.3.13.1.6
This attribute is the total number of frames with LRC errors, occurring in the Tx link prior to transmission onto the link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerNonOctetErrors		1.3.6.1.4.1.562.2.4.1.70.3.13.1.7
This attribute is the total number of frames that were non octet aligned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerOverruns		1.3.6.1.4.1.562.2.4.1.70.3.13.1.8
This attribute is the total number of frames received from the link for which overruns occurred.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerUnderruns		1.3.6.1.4.1.562.2.4.1.70.3.13.1.9
This attribute is the total number of frames transmitted to the link for which underruns occurred.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerLargeFrmErrors		1.3.6.1.4.1.562.2.4.1.70.3.13.1.10
This attribute is the total number of frames received which were too large. The frame execeeded the maximumFrameLengthLimit provisioned attribute or it contained more than the 255 block hardware limit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerFrmModeErrors		1.3.6.1.4.1.562.2.4.1.70.3.13.1.11
This attribute is the total number of frames detected with framing mode errors. A framingModeError is flagged when frames are inconsistent with the specified framingType, that is when interrupting frames are used while running in hdlc mode.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniFramerUtilTable		1.3.6.1.4.1.562.2.4.1.70.3.14
This group contains the link utilizaiton operational data for a Framer component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniFramerUtilEntry

frNniFramerUtilEntry		1.3.6.1.4.1.562.2.4.1.70.3.14.1
An entry in the frNniFramerUtilTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniFramerUtilEntry

frNniFramerNormPrioLinkUtilToIf		1.3.6.1.4.1.562.2.4.1.70.3.14.1.1
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) sent to the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge32	0..100

frNniFramerNormPrioLinkUtilFromIf		1.3.6.1.4.1.562.2.4.1.70.3.14.1.3
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) received from the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge32	0..100

frNniLmi		1.3.6.1.4.1.562.2.4.1.70.4
OBJECT IDENTIFIER

frNniLmiRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.4.1
This entry controls the addition and deletion of frNniLmi components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLmiRowStatusEntry

frNniLmiRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.4.1.1
A single entry in the table represents a single frNniLmi component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLmiRowStatusEntry

frNniLmiRowStatus		1.3.6.1.4.1.562.2.4.1.70.4.1.1.1
This variable is used as the basis for SNMP naming of frNniLmi components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

frNniLmiComponentName		1.3.6.1.4.1.562.2.4.1.70.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniLmiStorageType		1.3.6.1.4.1.562.2.4.1.70.4.1.1.4
This variable represents the storage type value for the frNniLmi tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniLmiIndex		1.3.6.1.4.1.562.2.4.1.70.4.1.1.10
This variable represents the index for the frNniLmi tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniLmiParmsTable		1.3.6.1.4.1.562.2.4.1.70.4.10
This group contains the provisionable attributes of the Local Management Interface component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLmiParmsEntry

frNniLmiParmsEntry		1.3.6.1.4.1.562.2.4.1.70.4.10.1
An entry in the frNniLmiParmsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLmiParmsEntry

frNniLmiProcedures		1.3.6.1.4.1.562.2.4.1.70.4.10.1.1
This attribute selects the procedures to be used for the Local Management Interface. The following are the supported procedures: none: Local Management Interface procedures are not running on this interface. This accommodates Frame Relay user equipment which didn't implement any LMI procedures. In this case, the remaining attributes of this group are ignored. ansi: Local Management Interface procedures from the ANSI specification are supported. DLCI 0 is used for the LMI protocol. itu: Local Management Interface procedures from the ITU-T specification are supported. DLCI 0 is used for the LMI protocol. Was previously ccitt. autoConfigure: The interface determines automatically which Local Management Interface procedures to use. The procedures currently being used can be seen in the operational attribute opProcedures.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), ansi(2), itu(3), autoConfigure(4)

frNniLmiAsyncStatusReport		1.3.6.1.4.1.562.2.4.1.70.4.10.1.2
This attribute selects the use of asynchronous PVC status report procedures as specified in ANSI and CCITT specification.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniLmiErrorEventThreshold		1.3.6.1.4.1.562.2.4.1.70.4.10.1.3
For the network-side-procedure, an event is defined as follows: (1) receipt of a STATUS ENQUIRY message, or (2) expiration of timer T392. An error event is (1) nonreceipt of STATUS ENQUIRY in T392 seconds; (2) invalid format of a LMI message; (3) invalid receive sequence number. For the user-side-procedure, an event is defined as a polling cycle or a status enquiry and status report exchange. An error event is (1) non-receipt of a STATUS within the polling cycle, or (2) invalid format of a LMI message, or (3) invalid sequence number This attribute specifies the number of error events which, if they occur within eventCount events, will cause a protocol error condition. The condition is cleared after eventCount sequential correct events occur. It must be less than or equal to eventCount (n393)
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	1..10

frNniLmiEventCount		1.3.6.1.4.1.562.2.4.1.70.4.10.1.4
This attribute specifies the number of contiguous events within which no more than eventErrorThreshold error events are allowed. It must be greater than or equal to errorEventThreshold (n392).
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	1..10

frNniLmiCheckPointTimer		1.3.6.1.4.1.562.2.4.1.70.4.10.1.5
This attribute selects the time (in seconds) within which a STATUS ENQUIRY message is expected. It must be greater than linkVerificationTimer (t391).
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	5 | 10 | 15 | 20 | 25 | 30

frNniLmiIgnoreActiveBit		1.3.6.1.4.1.562.2.4.1.70.4.10.1.7
This attribute specifies whether the Frame Relay LMI Active Bit (A-bit) has a bearing on the transfer of user data across this Frame Relay interface for both directions of traffic flow. When this attribute is set to yes, the A-bit status of a user DLCI connection does not affect data transfer. When this attribute is set to no, data received from the local interface is discarded if an A-bit =0 condition exists towards the local user. Data being sent to the local interface is discarded if an A- bit = 0 condition exists towards the local user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniLmiNniParmsTable		1.3.6.1.4.1.562.2.4.1.70.4.11
This group contains the provisionable attributes of the Local Management Interface component which are unique to NNI.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLmiNniParmsEntry

frNniLmiNniParmsEntry		1.3.6.1.4.1.562.2.4.1.70.4.11.1
An entry in the frNniLmiNniParmsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLmiNniParmsEntry

frNniLmiFullStatusPollingCycles		1.3.6.1.4.1.562.2.4.1.70.4.11.1.1
This attribute specifies how frequently the Frame Relay NNI service should initiate a Status Enquiry for a full PVC status report. A polling cycle is a Status Enquiry and Status Report exchange.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	1..255

frNniLmiLinkVerificationTimer		1.3.6.1.4.1.562.2.4.1.70.4.11.1.2
This attribute specifies how frequently the Frame Relay NNI service should initiate a Status Enquiry for link integrity verification. It must be less than checkPointTimer (t392).
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	5 | 10 | 15 | 20 | 25 | 30

frNniLmiStateTable		1.3.6.1.4.1.562.2.4.1.70.4.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLmiStateEntry

frNniLmiStateEntry		1.3.6.1.4.1.562.2.4.1.70.4.12.1
An entry in the frNniLmiStateTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLmiStateEntry

frNniLmiAdminState		1.3.6.1.4.1.562.2.4.1.70.4.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	locked(0), unlocked(1), shuttingDown(2)

frNniLmiOperationalState		1.3.6.1.4.1.562.2.4.1.70.4.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

frNniLmiUsageState		1.3.6.1.4.1.562.2.4.1.70.4.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(0), active(1), busy(2)

frNniLmiPsiTable		1.3.6.1.4.1.562.2.4.1.70.4.13
This group provides the protocol status of the Local Management Interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLmiPsiEntry

frNniLmiPsiEntry		1.3.6.1.4.1.562.2.4.1.70.4.13.1
An entry in the frNniLmiPsiTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLmiPsiEntry

frNniLmiProtocolStatus		1.3.6.1.4.1.562.2.4.1.70.4.13.1.1
This attribute indicates whether the LMI is in an error condition or whether the LMI procedures are behaving normally. When operating with no LMI protocol, this attribute is always set to normalCondition. When operating with LMI procedures, this attribute is set to errorCondition after n392 of the last n393 events are in error. The consequence of an errorCondition is that all DLCIs on this interface will become inactive in both directions. The errorCondition is lifted and a normalCondition is indicated when a sufficient number of events have occurred without error. In ANSI, this occurs when n393 consecutive good events take place. If the procedures attribute is set to autoConfigure, this attribute is se to configuring while adaptive LMI determines which LMI procedures are running on the link. A single LMI error event during auto configuration causes the attribute value to change to errorCondition. If during configuring no LMI message is received, an LMI errorCondition is raised after n392 x t392 seconds.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	errorCondition(0), normalCondition(1), configuring(2)

frNniLmiOpProcedures		1.3.6.1.4.1.562.2.4.1.70.4.13.1.2
This attribute indicates the procedures being used for the Local Management Interface. This attribute should be ignored if protocolStatus is not normalCondition. The following procedures are supported: none: Local Management Interface procedures are not running on this interface. This accommodates Frame Relay user equipment that has not implemented any LMI procedures. ansi: Local Management Interface procedures from the ANSI specification are running. DLCI 0 is used for the LMI protocol. itu: Local Management Interface procedures from the ITU-T specification are running. DLCI 0 is used for the LMI protocol. Was previously ccitt. unknown: Local Management Interface procedures have yet to be determined by Adaptive LMI.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), ansi(2), itu(3), unknown(4)

frNniLmiStatsTable		1.3.6.1.4.1.562.2.4.1.70.4.14
This group contains the operational statistics for the Frame Relay NNI Local Management Interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLmiStatsEntry

frNniLmiStatsEntry		1.3.6.1.4.1.562.2.4.1.70.4.14.1
An entry in the frNniLmiStatsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLmiStatsEntry

frNniLmiKeepAliveStatusToIf		1.3.6.1.4.1.562.2.4.1.70.4.14.1.1
This attribute counts the number of Local Management Interface keep alive status messages sent to the external network in response to a status enquiry for keep alive status. When the maximum count is exceeded it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiFullStatusToIf		1.3.6.1.4.1.562.2.4.1.70.4.14.1.2
This attribute counts the number of Local Management Interface full status messages sent to the external network in response to a status enquiry for keep alive or full status. When the maximum count is exceeded it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiKeepAliveStatusEnqFromIf		1.3.6.1.4.1.562.2.4.1.70.4.14.1.3
This attribute counts the number of Local Management Interface valid keep alive status enquiry messages received from the external network. When the maximum count is exceeded it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiFullStatusEnqFromIf		1.3.6.1.4.1.562.2.4.1.70.4.14.1.4
This attribute counts the number of Local Management Interface valid full status enquiry messages received from the external network. When the maximum count is exceeded it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiNetworkSideEventHistory		1.3.6.1.4.1.562.2.4.1.70.4.14.1.5
This attribute displays the Local Management Interface network side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The leftmost event is the most recent to occur. The provisioned eventCount (nN3/ N393) dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status enquiry message. An error event is either a nT2/T392 timer expiry or receipt of a status enquiry with bad sequence numbers.
Status: mandatory	Access: read-only
OBJECT-TYPE
	AsciiString	Size(1..10)

frNniLmiUserSideEventHistory		1.3.6.1.4.1.562.2.4.1.70.4.14.1.6
This attribute displays the Local Management Interface user side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The leftmost event is the most recent to occur. The provisioned eventCount (nN3/ N393) dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status message. An error event is either a nT1/T391 timer expiry or receipt of a status message with bad sequence numbers.
Status: mandatory	Access: read-only
OBJECT-TYPE
	AsciiString	Size(1..10)

frNniLmiProtocolErrors		1.3.6.1.4.1.562.2.4.1.70.4.14.1.7
This attribute counts the number of Local Management Interface protocol errors. It is the sum of the sequence (sequenceErrors and statusSequenceErrors) and timeout (pollingVerifTimeouts and noStatusReportCount) errors. When the maximum count is exceeded it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiUnexpectedIes		1.3.6.1.4.1.562.2.4.1.70.4.14.1.8
This attribute counts the number of Local Management Interface frames received with an Information Element identifier that is unknown or unexpected. An unexpected Information Element is not a protocol error. When the maximum count is exceeded, this counter wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiSequenceErrors		1.3.6.1.4.1.562.2.4.1.70.4.14.1.9
This attribute counts the number of Local Management Interface Status Enquiry message sequence errors. A sequence error is receipt of a Status Enquiry message with a receive sequence number not equal to the last send sequence number. When the maximum count is exceeded the counter wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiStatusSequenceErrors		1.3.6.1.4.1.562.2.4.1.70.4.14.1.10
This attribute counts the number of Local Management Interface Status message sequence errors. A sequence error is receipt of a Status message with a receive sequence number not equal to the last send sequence number. When the maximum count is exceeded the counter wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiUnexpectedReports		1.3.6.1.4.1.562.2.4.1.70.4.14.1.11
This attribute counts the number of Local Management Interface frames received with an unknown or unexpected report type. An unexpected report type is not a protocol error. When the maximum count is exceeded the counter wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiPollingVerifTimeouts		1.3.6.1.4.1.562.2.4.1.70.4.14.1.12
This attribute counts the number of checkPointTImer (t392) timer expiries occurring on the Local Management Interface. When the maximum count is exceeded the counter wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLmiNoStatusReportCount		1.3.6.1.4.1.562.2.4.1.70.4.14.1.13
This attribute counts the number of times when no status report or an invalid status report comes from the external network. This attribute is incremented in two cases: i) after a status enquiry is sent out and T391 timer expires without having a status report received. ii) an invalid status report is received. When the maximum count is exceeded it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniDlci		1.3.6.1.4.1.562.2.4.1.70.5
OBJECT IDENTIFIER

frNniDlciRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.5.1
This entry controls the addition and deletion of frNniDlci components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciRowStatusEntry

frNniDlciRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.5.1.1
A single entry in the table represents a single frNniDlci component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciRowStatusEntry

frNniDlciRowStatus		1.3.6.1.4.1.562.2.4.1.70.5.1.1.1
This variable is used as the basis for SNMP naming of frNniDlci components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniDlciComponentName		1.3.6.1.4.1.562.2.4.1.70.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDlciStorageType		1.3.6.1.4.1.562.2.4.1.70.5.1.1.4
This variable represents the storage type value for the frNniDlci tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDlciIndex		1.3.6.1.4.1.562.2.4.1.70.5.1.1.10
This variable represents the index for the frNniDlci tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	16..1007

frNniDlciStateTable		1.3.6.1.4.1.562.2.4.1.70.5.10
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciStateEntry

frNniDlciStateEntry		1.3.6.1.4.1.562.2.4.1.70.5.10.1
An entry in the frNniDlciStateTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciStateEntry

frNniDlciAdminState		1.3.6.1.4.1.562.2.4.1.70.5.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	locked(0), unlocked(1), shuttingDown(2)

frNniDlciOperationalState		1.3.6.1.4.1.562.2.4.1.70.5.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

frNniDlciUsageState		1.3.6.1.4.1.562.2.4.1.70.5.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(0), active(1), busy(2)

frNniDlciAvailabilityStatus		1.3.6.1.4.1.562.2.4.1.70.5.10.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

frNniDlciProceduralStatus		1.3.6.1.4.1.562.2.4.1.70.5.10.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniDlciControlStatus		1.3.6.1.4.1.562.2.4.1.70.5.10.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniDlciAlarmStatus		1.3.6.1.4.1.562.2.4.1.70.5.10.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniDlciStandbyStatus		1.3.6.1.4.1.562.2.4.1.70.5.10.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hotStandby(0), coldStandby(1), providingService(2), notSet(15)

frNniDlciUnknownStatus		1.3.6.1.4.1.562.2.4.1.70.5.10.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	false(0), true(1)

frNniDlciAbitTable		1.3.6.1.4.1.562.2.4.1.70.5.12
This group contains the A-Bit status information for this Data Link Connection Identifier.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciAbitEntry

frNniDlciAbitEntry		1.3.6.1.4.1.562.2.4.1.70.5.12.1
An entry in the frNniDlciAbitTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciAbitEntry

frNniDlciABitStatusToIf		1.3.6.1.4.1.562.2.4.1.70.5.12.1.1
This attribute is the most recent A-bit status sent to the interface. The A-bit status is part of the LMI protocol, and indicates willingness to accept data from the local interface. When an inactive setting is sent out, the Frame Relay service will discard any data offered from the local interface. When an active setting is sent out, the Frame Relay service will try to process all data offered from the local interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(0), active(1)

frNniDlciABitReasonToIf		1.3.6.1.4.1.562.2.4.1.70.5.12.1.2
This attribute provides the reason (if any) for an inactive status to be sent to the interface. This reason is not applicable for an active status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(0), remoteUserSignaled(1), localLmiError(2), remoteLmiError(3), localLinkDown(4), remoteLinkDown(5), pvcDown(6)

frNniDlciABitStatusFromIf		1.3.6.1.4.1.562.2.4.1.70.5.12.1.3
This attribute is the most recent A-Bit status received from the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(0), active(1)

frNniDlciABitReasonFromIf		1.3.6.1.4.1.562.2.4.1.70.5.12.1.4
This attribute provides the reason (if any) for an inactive status to be sent to the subnet. This reason is not applicable for an active status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(0), remoteUserSignaled(1), localLmiError(2), localLinkDown(4), missingFromLmiReport(7)

frNniDlciLoopbackState		1.3.6.1.4.1.562.2.4.1.70.5.12.1.5
This attribute has the value on when the DLCI is in loopback mode and off otherwise. This loopback command verbs start and stop are used to initiate and terminate the loopback mode for a DLCI. While loopbackState is on, the local LMI will report to the interface the A- bit status as active. Also an active A-bit signal will be reliably propagated across the subnet to the remote DLCI.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniDlciSpOpTable		1.3.6.1.4.1.562.2.4.1.70.5.13
This group defines the service and traffic parameters specific to this instance of DLCI. For PVCs, the values of attributes with the exception of the measurementInterval should be identical to those in the group FrsDataLinkConnectionProv under the FrsNniServiceParametersProv component. For SVC's, the values of attributes may be different from the values provisioned under the Signaling subcomponent, if Q933 negotiations has ocurred to alter service parameters.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciSpOpEntry

frNniDlciSpOpEntry		1.3.6.1.4.1.562.2.4.1.70.5.13.1
An entry in the frNniDlciSpOpTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciSpOpEntry

frNniDlciMaximumFrameSize		1.3.6.1.4.1.562.2.4.1.70.5.13.1.1
This attribute specifies the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Vendor Forum Specification.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	1..8187

frNniDlciRateEnforcement		1.3.6.1.4.1.562.2.4.1.70.5.13.1.2
This attribute is obsolete. It provided the same information as the provision attribute rateEnforcement in dlci/* sp.
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniDlciCommittedInformationRate		1.3.6.1.4.1.562.2.4.1.70.5.13.1.3
This attribute specifies the committed information rate (CIR) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (t) that is determined internally based on CIR and the committed burst size (Bc). An exception to this occurs when CIR is provisioned to be zero, in which case the measurement interval (t) must be provisioned explicitly. This attribute should be ignored when rateEnforcement is off.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..2048000

frNniDlciCommittedBurstSize		1.3.6.1.4.1.562.2.4.1.70.5.13.1.4
This attribute specifies the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute should be ignored when rateEnforcement is off.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..2048000

frNniDlciExcessBurstSize		1.3.6.1.4.1.562.2.4.1.70.5.13.1.5
This attribute specifies the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. This attribute should be ignored when rateEnforcement is off.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..2048000

frNniDlciMeasurementInterval		1.3.6.1.4.1.562.2.4.1.70.5.13.1.6
This attribute specifies the time interval (in milliseconds) over which rates and burst sizes are measured. This attribute should be ignored when rateEnforcement is off.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciRateAdaptation		1.3.6.1.4.1.562.2.4.1.70.5.13.1.7
This attribute is obsolete. It provided the information which is now in the provision attribute rateAdaptation in dlci/* sp.
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1), eirOnly(2)

frNniDlciAccounting		1.3.6.1.4.1.562.2.4.1.70.5.13.1.8
This attribute specifies whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the accountingOn bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniDlciEmissionPriorityToIf		1.3.6.1.4.1.562.2.4.1.70.5.13.1.9
This attribute indicates the emission priority of frames sent to the interface. A larger value denotes a higher priority.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0 | 1 | 2 | 3

frNniDlciTransferPriToNwk		1.3.6.1.4.1.562.2.4.1.70.5.13.1.10
This attribute indicates the priority at which data is transferred to the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..15

frNniDlciTransferPriFromNwk		1.3.6.1.4.1.562.2.4.1.70.5.13.1.11
This attribute indicates the priority at which data is transferred from the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..15

frNniDlciStatsTable		1.3.6.1.4.1.562.2.4.1.70.5.14
This group contains the operational statistics for the Frame Relay Data Link Connection Identifier.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciStatsEntry

frNniDlciStatsEntry		1.3.6.1.4.1.562.2.4.1.70.5.14.1
An entry in the frNniDlciStatsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciStatsEntry

frNniDlciFrmToIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.1
This attribute counts the frames sent out the interface. When the maximum count is reached the count wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciFecnFrmToIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.2
This attribute counts the frames sent to the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciBecnFrmToIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.3
This attribute counts the frames sent to the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciBciToSubnet		1.3.6.1.4.1.562.2.4.1.70.5.14.1.4
This attribute counts the frames sent into the local network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDeFrmToIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.5
This attribute counts the frames sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscCongestedToIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.6
This attribute counts the number of frame discards at the Frame Relay service due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscDeCongestedToIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.7
This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the Frame Relay service, due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciFrmFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.8
This attribute counts the frames received from the interface. It includes the frames that are discarded due to error or excess. When the maximum count is reached the count wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciFecnFrmFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.9
This attribute counts the frames received from the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciBecnFrmFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.10
This attribute counts the frames received from the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciFciFromSubnet		1.3.6.1.4.1.562.2.4.1.70.5.14.1.11
This attribute counts the frames received from the network with the Forward Congestion Indication (FCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciBciFromSubnet		1.3.6.1.4.1.562.2.4.1.70.5.14.1.12
This attribute counts the frames received from the network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDeFrmFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.13
This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciExcessFrmFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.14
This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscExcessFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.15
This attribute counts the frames which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscFrameAbit		1.3.6.1.4.1.562.2.4.1.70.5.14.1.16
This attribute counts the number of frame discards at the Frame Relay Service, due to an inactive PVC status, in the direction toward the local network. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscCongestedFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.17
This attribute counts the number of frame discards at the Frame Relay service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscDeCongestedFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.18
This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the Frame Relay service, due to local congestion, in the direction toward the local network. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciErrorShortFrmFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.19
This attribute counts the frames received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciErrorLongFrmFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.20
This attribute counts the frames received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Frames whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciBecnFrmSetByService		1.3.6.1.4.1.562.2.4.1.70.5.14.1.21
This attribute counts the number of frames with BECN set by the Frame Relay service. It is incremented whenever the Frame Relay service sets BECN on a frame upon detecting local congestion. This count is incremented regardless of whether the frame already bears a set BECN bit since its use is to determine the place of congestion. When the count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciBytesToIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.22
This attribute counts the bytes sent out the interface. When the maximum count is reached the count wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDeBytesToIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.23
This attribute counts the bytes sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscCongestedToIfBytes		1.3.6.1.4.1.562.2.4.1.70.5.14.1.24
This attribute counts the number of byte discards at the Frame Relay service due to local congestion in the direction toward the link. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscDeCongestedToIfBytes		1.3.6.1.4.1.562.2.4.1.70.5.14.1.25
This attribute counts the number of discard eligible (DE=1) byte discards at the Frame Relay service due to local congestion in the direction toward the link. When the maximum count is reached the count wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciBytesFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.26
This attribute counts the bytes received from the interface. Bytes that are discarded due to error or excess are not counted. When the maximum count is reached the count wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDeBytesFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.27
This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciExcessBytesFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.28
This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscExcessFromIfBytes		1.3.6.1.4.1.562.2.4.1.70.5.14.1.29
This attribute counts the bytes which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscByteAbit		1.3.6.1.4.1.562.2.4.1.70.5.14.1.30
This attribute counts the bytes which were discarded due to aBit turned off.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscCongestedFromIfBytes		1.3.6.1.4.1.562.2.4.1.70.5.14.1.31
This attribute counts the number of byte discards at the Frame Relay service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscDeCongestedFromIfBytes		1.3.6.1.4.1.562.2.4.1.70.5.14.1.32
This attribute counts the number of discard eligible (DE=1) byte discards at the Frame Relay service due to local congestion in the direction toward the network. When the maximum count is reached the count wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciErrorShortBytesFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.33
This attribute counts the bytes received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciErrorLongBytesFromIf		1.3.6.1.4.1.562.2.4.1.70.5.14.1.34
This attribute counts the bytes received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Bytes whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciRateAdaptReduct		1.3.6.1.4.1.562.2.4.1.70.5.14.1.35
This attribute counts the number of rate reductions due to rate adaptation. Rate adaptation causes the allowed rate to be reduced in steps. After each reduction, a period of time is awaited before further action is taken. At the end of this period, the allowed rate is further reduced if congestion is still prevalent. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciRateAdaptReductPeriod		1.3.6.1.4.1.562.2.4.1.70.5.14.1.36
This attribute provides a cumulative count of the amount of time that rate adaptation procedures have been in effect. When this count reaches maximum, it wraps to zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciTransferPriorityToNetwork		1.3.6.1.4.1.562.2.4.1.70.5.14.1.37
This attribute is obsolete. It is replaced by attribute transferPriorityToNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)

frNniDlciTransferPriorityFromNetwork		1.3.6.1.4.1.562.2.4.1.70.5.14.1.38
This attribute is obsolete. It is replaced by attribute transferPriorityFromNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)

frNniDlciCirPresent		1.3.6.1.4.1.562.2.4.1.70.5.14.1.39
This attribute provides the actual Committed Information Rate (CIR) enforced for this DLCI. This number is in units of 800 bits/ sec, since that is the internal resolution of Passport rate enforcement. If rateEnforcement is off, then this number does not have meaning. Normally, this attribute matches the provisioned CIR for the DLCI. But when Rate Adaptation is active, then this number will vary to represent the actual Allowed CIR at the moment that this attribute is collected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciEirPresent		1.3.6.1.4.1.562.2.4.1.70.5.14.1.40
This attribute provides the actual Excess Information Rate (EIR) enforced for this DLCI. This number is in units of 800 bits/sec, since that is the internal resolution of Passport rate enforcement. If rateEnforcement is off, then this number does not have meaning. Normally, this attribute matches the provisioned EIR for the DLCI. But when Rate Adaptation is active, then this number will vary to represent the actual Allowed EIR at the moment that this attribute is collected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciIntTable		1.3.6.1.4.1.562.2.4.1.70.5.15
This group contains the operational statistics for the Frame Relay Data Link Connection Identifier interval data (accounting data).
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciIntEntry

frNniDlciIntEntry		1.3.6.1.4.1.562.2.4.1.70.5.15.1
An entry in the frNniDlciIntTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciIntEntry

frNniDlciStartTime		1.3.6.1.4.1.562.2.4.1.70.5.15.1.1
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes. A new interval period is started each time an accounting record is generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	EnterpriseDateAndTime	Size(0|19)

frNniDlciTotalIngressBytes		1.3.6.1.4.1.562.2.4.1.70.5.15.1.2
This attribute counts the total bytes received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned64	Size(8)

frNniDlciTotalEgressBytes		1.3.6.1.4.1.562.2.4.1.70.5.15.1.3
This attribute counts the total bytes sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned64	Size(8)

frNniDlciEirIngressBytes		1.3.6.1.4.1.562.2.4.1.70.5.15.1.4
This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned64	Size(8)

frNniDlciEirEgressBytes		1.3.6.1.4.1.562.2.4.1.70.5.15.1.5
This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned64	Size(8)

frNniDlciDiscardedBytes		1.3.6.1.4.1.562.2.4.1.70.5.15.1.6
This attribute counts the total bytes in invalid frames received from the interface and discarded at the DLCI since the start of the interval period. This count is a sum of octets in frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned64	Size(8)

frNniDlciTotalIngressSegFrm		1.3.6.1.4.1.562.2.4.1.70.5.15.1.7
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames received from the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciTotalEgressSegFrm		1.3.6.1.4.1.562.2.4.1.70.5.15.1.8
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciEirIngressSegFrm		1.3.6.1.4.1.562.2.4.1.70.5.15.1.9
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciEirEgressSegFrm		1.3.6.1.4.1.562.2.4.1.70.5.15.1.10
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDiscardedSegFrm		1.3.6.1.4.1.562.2.4.1.70.5.15.1.11
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in invalid frames received from the interface and discarded at the DLCI. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of invalid frames received from the interface and discarded at the DLCI. Segments of frames are counted since the start of the interval period. The count is reset to zero when an accounting record is generated. The count is a sum of segments in frames or frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciCirPresentObs		1.3.6.1.4.1.562.2.4.1.70.5.15.1.12
This attribute has moved to the statistics subgroup. See cirPresent..
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciEirPresentObs		1.3.6.1.4.1.562.2.4.1.70.5.15.1.13
This attribute has moved to the statistics subgroup. See eirPresent.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciRateEnforcementPresent		1.3.6.1.4.1.562.2.4.1.70.5.15.1.14
This attribute is obsolete. It is the same as the provisioned rateEnforcement attributed..
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniDlciRateAdaptationPresent		1.3.6.1.4.1.562.2.4.1.70.5.15.1.15
This attribute is obsolete. See the provisioning attribute rateAdaptation for the data that it intended to provide.
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniDlciLocalRateAdaptOccurred		1.3.6.1.4.1.562.2.4.1.70.5.15.1.16
This attribute specifies whether rate adaptation has occurred on this user Data Link Connection on this Frame Relay interface.The count is reset to no when an accounting record is generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniDlciCallReferenceNumber		1.3.6.1.4.1.562.2.4.1.70.5.15.1.17
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Hex	0..16777215

frNniDlciElapsedDifference		1.3.6.1.4.1.562.2.4.1.70.5.15.1.18
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since the call started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciDc		1.3.6.1.4.1.562.2.4.1.70.5.2
OBJECT IDENTIFIER

frNniDlciDcRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.5.2.1
This entry controls the addition and deletion of frNniDlciDc components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciDcRowStatusEntry

frNniDlciDcRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.5.2.1.1
A single entry in the table represents a single frNniDlciDc component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciDcRowStatusEntry

frNniDlciDcRowStatus		1.3.6.1.4.1.562.2.4.1.70.5.2.1.1.1
This variable is used as the basis for SNMP naming of frNniDlciDc components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

frNniDlciDcComponentName		1.3.6.1.4.1.562.2.4.1.70.5.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDlciDcStorageType		1.3.6.1.4.1.562.2.4.1.70.5.2.1.1.4
This variable represents the storage type value for the frNniDlciDc tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDlciDcIndex		1.3.6.1.4.1.562.2.4.1.70.5.2.1.1.10
This variable represents the index for the frNniDlciDc tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniDlciDcOptionsTable		1.3.6.1.4.1.562.2.4.1.70.5.2.10
Options group defines attributes associated with direct call. It defines complete connection in terms of path and call options. This connection can be permanent (pvc) or switched (svc). It can have facilities. The total number of bytes of facilities including the facility codes, and all of the facility data from all of the four classes of facilities: CCITT_Facilities DTE_Facilities National_Facilities International_Facilities must not exceed 512 bytes.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciDcOptionsEntry

frNniDlciDcOptionsEntry		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1
An entry in the frNniDlciDcOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciDcOptionsEntry

frNniDlciDcRemoteNpi		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.3
Destination Numbering Plan Indicator (Npi) indicates the numbering plan used in the remoteDna.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

frNniDlciDcRemoteDna		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.4
This attribute specifies the Data Network Address (DNA) of the remote. This is the called (destination) DTE address (DNA) to which this direct call will be sent. Initially, the called DTE address attribute must be present, that is, there must be a valid destination address. However, it may be possible in the future to configure the direct call with a mnemonic address, in which case, this attribute will contain a zero-length DNA, and the mnemonic address will be carried as one of the facilities.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DigitString	Size(1..15)

frNniDlciDcRemoteDlci		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.5
L(LCN) of the destination. This attribute provides the remote LCN (Logical Channel Number) - it is used only for PVCs, where the parameter Type is set to a value of PVC.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	16..1007

frNniDlciDcType		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.6
This attribute specifies the type of Vc call: permanentMaster, permanentSlave, permanentSlaveWithBackup, permanentBackupSlave. If the value is set to permanentMaster, then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentSlave, permanentBackupSlave or permanentSlaveWithBackup. The Connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It will attempt to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentMaster. The Connection cannot be established if the remote end is defined as anything else. The permanentSlave end will attempt to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote interface end is defined as anything else. The permanentSlaveWithBackup end will attempt to call once per minute. When type is set to permanentSlaveWithBackup connection will be cleared if interface becomes unavailable. This enables a retry of the connection which can be redirected to permanentBackupSlave. If the value is set to permanentBackupSlave then a permanent connection will be established between the 2 ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the redirection system. If the permanentSlaveWithBackup interface becomes visible again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish pvc call.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	permanentMaster(1), permanentSlave(2), permanentBackupSlave(3), permanentSlaveWithBackup(4)

frNniDlciDcTransferPriority		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.9
This attribute specifies the transfer priority to network for the outgoing calls using this particular DLCI. It overRides the defaultTransferPriority provisioned in its associated Dna component. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n is the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned under the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required. The default of transferPriority is useDnaDefTP. It means using the provisioning value under defaultTransferPriority of its associated Dna for this DLCI.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), useDnaDefTP(255)

frNniDlciDcDiscardPriority		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.10
This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning values: normal, high, and useDnaDefPriority. Traffic with normal priority are discarded first than the traffic with high priority. The Dna default value (provisioned by outDefaultPriority) is taken if this attribute is set to the value useDnaDefPriority. The default of discardPriority is useDnaDefPriority.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(0), high(1), useDnaDefPriority(3)

frNniDlciDcDeDiscardPriority		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.11
This attribute specifies whether the discardPriority applies to DE frames for this DLCI. If deDiscardPriority is set to determinedByDiscardPriority, traffic with DE bit set will be discarded according to the setting of the discardPriority. If deDiscardPriority is set to lowest, all traffic with DE bit set will be treated the same and be sent to the subnet at the lowest discard priority.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	lowest(0), determinedByDiscardPriority(1)

frNniDlciDcDataPath		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.12
This attribute specifies the data path to be used by Virtual Circuits on this interface. The value of the dataPath attribute in the Dna component is overridden by this attribute if the value is not useDnaValue. This value applies to the connection after data transfer state is reached. All the data and control trafic will be sent using this data path. If the provisioned dataPath is not available the connection is not established. The value of the dataPath is signalled by both ends of the connection. If this value is not the same at both ends dprsOnly is used for the duration of the connection. A virtual circuit connection is always established using dprsOnly even if this attribute is provisioned as some other value. dprsOnly - dynamic packet routing system is used dprsMcsOnly - dprs Multi-Service Cut-Through Switching path is used. dprsMcsFirst - dprs Multi-Service Cut-Through Switching path is used if it is available. If it is not avaliable dprsOnly is used. useDnaValue - use the value provisioned in Dna component.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dprsOnly(0), dprsMcsOnly(1), dprsMcsFirst(2), useDnaValue(3)

frNniDlciDcCugIndex		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.13
This attribute specifies the CUG index which is to be signalled in PVC call requests to the remote end. The type of CUG signalling is defined in attribute cugType in this component.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

frNniDlciDcCugType		1.3.6.1.4.1.562.2.4.1.70.5.2.10.1.14
This attribute specifies the type of CUG signalling to be used in PVC call request. Index of CUG to be used is defined in attribute cugIndex in this component. Possible values are: cug - signal cug cugOa - signal cug with outgoing access doNotSignal - no CUG in call request
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	doNotSignal(0), cug(3), cugOa(9)

frNniDlciDcNfaTable		1.3.6.1.4.1.562.2.4.1.70.5.2.202
This is the i'th National facility required for this direct call. Within the provisioning system, the user specifies the facility code along with the facility parameters. The facility is represented internally as a hexadecimal string following the X.25 CCITT representation for facility data. Two explicit attributes discardPriority and pathSensitivity are created to replace H.01 and H.30 in the group VcsDirectCallOptionsProv of this file. The migrate escape here (DcComponent::migrateFaxEscape) propagates the old provisioning data under H.01 and H.30 into discardPriority and transferPriority. The rule of the above propagation are: 0 in H.01 is equivalent to discardPriority 0; 1 in H.01 is equivalent to discardPriority 1. And 0 in H.30 is equivalent to transferPriority throughput; 1 in H.30 is equivalent to pathSensitivity delay. Please refer to discardPriority and pathSensitivity for more information on how to use them.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciDcNfaEntry

frNniDlciDcNfaEntry		1.3.6.1.4.1.562.2.4.1.70.5.2.202.1
An entry in the frNniDlciDcNfaTable.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	FrNniDlciDcNfaEntry

frNniDlciDcNfaIndex		1.3.6.1.4.1.562.2.4.1.70.5.2.202.1.1
This variable represents the index for the frNniDlciDcNfaTable.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Integer32	1 | 48

frNniDlciDcNfaValue		1.3.6.1.4.1.562.2.4.1.70.5.2.202.1.2
This variable represents an individual value for the frNniDlciDcNfaTable.
Status: obsolete	Access: read-write
OBJECT-TYPE
	HexString	Size(0..128)

frNniDlciDcNfaRowStatus		1.3.6.1.4.1.562.2.4.1.70.5.2.202.1.3
This variable is used to control the addition and deletion of individual values of the frNniDlciDcNfaTable.
Status: obsolete	Access: write-only
OBJECT-TYPE
	RowStatus

frNniDlciVc		1.3.6.1.4.1.562.2.4.1.70.5.3
OBJECT IDENTIFIER

frNniDlciVcRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.5.3.1
This entry controls the addition and deletion of frNniDlciVc components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciVcRowStatusEntry

frNniDlciVcRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.5.3.1.1
A single entry in the table represents a single frNniDlciVc component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciVcRowStatusEntry

frNniDlciVcRowStatus		1.3.6.1.4.1.562.2.4.1.70.5.3.1.1.1
This variable is used as the basis for SNMP naming of frNniDlciVc components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

frNniDlciVcComponentName		1.3.6.1.4.1.562.2.4.1.70.5.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDlciVcStorageType		1.3.6.1.4.1.562.2.4.1.70.5.3.1.1.4
This variable represents the storage type value for the frNniDlciVc tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDlciVcIndex		1.3.6.1.4.1.562.2.4.1.70.5.3.1.1.10
This variable represents the index for the frNniDlciVc tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniDlciVcCadTable		1.3.6.1.4.1.562.2.4.1.70.5.3.10
This group represents operational call data related to Frame Relay Vc. It can be displayed only for Frame Relay Vc which is created by application.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciVcCadEntry

frNniDlciVcCadEntry		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1
An entry in the frNniDlciVcCadTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciVcCadEntry

frNniDlciVcType		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.1
This attribute displays the type of call, pvc,svc or spvc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	svc(0), pvc(1), spvc(2)

frNniDlciVcState		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.2
This attribute displays the state of call control. P5 state is not supported but is listed for completness. Transitions from one state to another take very short time. state most often displayed is dataTransferP4.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)

frNniDlciVcPreviousState		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.3
This attribute displays the previous state of call control. This is a valuable field to determine how the processing is progressing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)

frNniDlciVcDiagnosticCode		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.4
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

frNniDlciVcPreviousDiagnosticCode		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.5
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

frNniDlciVcCalledNpi		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.6
This attribute displays the Numbering Plan Indicator (NPI) of the called end.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

frNniDlciVcCalledDna		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.7
This attribute displays the Data Network Address (Dna) of the called (destination) DTE to which this call is sent. This address if defined at recieving end will complete Vc connection.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DigitString	Size(1..15)

frNniDlciVcCalledLcn		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.8
This attribute displays the Logical Channel Number of the called end. It is valid only after both ends of Vc exchanged relevant information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

frNniDlciVcCallingNpi		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.9
This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

frNniDlciVcCallingDna		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.10
This attribute displays the Data Network Address (Dna) of the calling end.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DigitString	Size(1..15)

frNniDlciVcCallingLcn		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.11
This attribute displays the Logical Channel Number of the calling end.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

frNniDlciVcAccountingEnabled		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.12
This attribute indicates that this optional section of accounting record is suppressed or permitted. If accountingEnabled is yes, conditions for generation of accounting record were met. These conditions include billing options, vc recovery conditions and Module wide accounting data options.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	yes(0), no(1)

frNniDlciVcFastSelectCall		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.13
This attribute displays that this is a fast select call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniDlciVcPathReliability		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.19
This attribute displays the path reliability.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	high(0), normal(1)

frNniDlciVcAccountingEnd		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.20
This attribute indicates if this end should generate an accounting record. Normally, callingEnd is the end to generate an accounting record.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	callingEnd(0), calledEnd(1)

frNniDlciVcPriority		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.21
This attribute displays whether the call is a normal or a high priority call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(0), high(1)

frNniDlciVcSegmentSize		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.22
This attribute displays the segment size (in bytes) used on the call. It is used to calculate the number of segments transmitted and received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4096

frNniDlciVcMaxSubnetPktSize		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.27
This attribute indicates the maximum packet size allowed on the Vc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4096

frNniDlciVcRcosToNetwork		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.28
This attribute indicates the routing metric routing class of service to the network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	throughput(0), delay(1), multimedia(2)

frNniDlciVcRcosFromNetwork		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.29
This attribute displays the routing metric Routing Class of Service from the Network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	throughput(0), delay(1), multimedia(2)

frNniDlciVcEmissionPriorityToNetwork		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.30
This attribute displays the network internal emission priotity to the network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(0), high(1), interrupting(2)

frNniDlciVcEmissionPriorityFromNetwork		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.31
This attribute displays the network internal emission priotity from the network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(0), high(1), interrupting(2)

frNniDlciVcDataPath		1.3.6.1.4.1.562.2.4.1.70.5.3.10.1.32
This attribute indicates the data path used by the connection. The data path is provisioned in Dna and DirectCall components. The displayed value of this attribute can be different from the provisioned value. If the connection is using dprsOnly data path, the string dprsOnly is displayed. (dynamic packet routing system) If the connection is using dprsMcsOnly data path, the string dprsMcsOnly is displayed. If the connection is using dprsMcsFirst data path, the string dprsMcsFirst is displayed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	AsciiString	Size(0..32)

frNniDlciVcIntdTable		1.3.6.1.4.1.562.2.4.1.70.5.3.11
This group defines display of interval data collected by Vc. Data in this group is variable and may depend on time when this display command is issued.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciVcIntdEntry

frNniDlciVcIntdEntry		1.3.6.1.4.1.562.2.4.1.70.5.3.11.1
An entry in the frNniDlciVcIntdTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciVcIntdEntry

frNniDlciVcCallReferenceNumber		1.3.6.1.4.1.562.2.4.1.70.5.3.11.1.1
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Hex	0..16777215

frNniDlciVcElapsedTimeTillNow		1.3.6.1.4.1.562.2.4.1.70.5.3.11.1.2
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since Vc started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16777215

frNniDlciVcSegmentsRx		1.3.6.1.4.1.562.2.4.1.70.5.3.11.1.3
This attribute displays the number of segments received at the time command was issued. This is the segment received count maintained by accounting at each end of the Vc. This counter is updated only when the packet cannot be successfully delivered out of the sink Vc and to the sink AP Conditions in which packets may be discarded by the sink Vc include: missing packets due to subnet discards, segmentation protocol violations due to subnet discard, duplicated and out-of-ranged packets and packets that arrive while Vc is in path recovery state.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16777215

frNniDlciVcSegmentsSent		1.3.6.1.4.1.562.2.4.1.70.5.3.11.1.4
This attribute displays the number of segments sent at the time command was issued. This is the segment sent count maintained by accounting at the source Vc. Vc only counts packets that Vc thinks can be delivered successfully into the subnet. In reality, these packets may be dropped by trunking, for instance. This counter is not updated when splitting fails, when Vc is in a path recovery state, when packet forwarding fails to forward this packet and when subsequent packets have to be discarded as we want to minimize the chance of out-of-sequence and do not intentionally send out-of- sequenced packets into the subnet.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16777215

frNniDlciVcStartTime		1.3.6.1.4.1.562.2.4.1.70.5.3.11.1.5
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes.
Status: mandatory	Access: read-only
OBJECT-TYPE
	EnterpriseDateAndTime	Size(0|19)

frNniDlciVcFrdTable		1.3.6.1.4.1.562.2.4.1.70.5.3.12
This group defines Frame Relay attributes collected by Frame Relay Vc. The purpose of Vc attributes is to aid end users and verification people to understand the Vc internal behavior. This is particularly useful when the network has experienced abnormality and we want to isolate problems and pinpoint trouble spots. Attributes are collected on a per Vc basis. Until a need is identified, statistics are not collected at a processor level. Each attribute is stored in a 32 bit field and is initialized to zero when a Vc enters into the data transfer state. When a PVC is disconnected and then connected again, the attributes will be reset. Attributes cannot be reset through other methods. Frame Relay Vc uses a best effort data packet delivery protocol and a different packet segmentation and combination methods from the General Vc. The Frame Relay Vc uses the same call setup and control mechanism (e.g. the support of non-flow control data packets) as in a General Vc. Most General Vc statistics and internal variables are used in a Frame Relay Vc and are displayed by software developers
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciVcFrdEntry

frNniDlciVcFrdEntry		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1
An entry in the frNniDlciVcFrdTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciVcFrdEntry

frNniDlciVcFrmCongestedToSubnet		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.2
This attribute displays the number of frames from link discarded due to lack of resources. It keeps track of the number of frames from link that have to be discarded. The discard reasons include insufficient memory for splitting the frame into smaller subnet packet size.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcCannotForwardToSubnet		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.3
This attribute displays the number of discarded packets that can not be forwarded into the subnet because of subnet congestion. Number of frames from link discarded due to failure in forwarding a packet from Vc into the subnet.- This attribute is increased when packet forwarding fails to forward a packet into the subnet. If a frame is split into multiple subnet packets and a partial packet has to be discarded, all subsequent partial packets that have not yet been delivered to the subnet will be discarded as well.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcNotDataXferToSubnet		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.4
This attribute records the number of frames from link discarded when the Vc tries to recover from internal path failure.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcOutOfRangeFrmFromSubnet		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.5
This attribute displays the number of frames from subnet discarded due to out of sequence range for arriving too late.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcCombErrorsFromSubnet		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.6
This attribute records the number of subnet packets discarded at the sink Vc due to the Vc segmentation and combination protocol error. Usually, this occurs when the subnet discards packets and thus this statistics can be used to guest the number of subnet packets that are not delivered to the Vc. It cannot be used as an actual measure because some subnet packets may have been delivered to Vc but have to be discarded because these are partial packets to a frame in which some other partial packets have not been properly delivered to Vc
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcDuplicatesFromSubnet		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.7
This attribute displays the number of subnet packets discarded due to duplication. Although packets are not retransmitted by the Frame Relay Vc, it is possible for the subnet to retransmit packets. When packets are out-of-sequenced and copies of the same packets arrive, then this attribute is increased.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcNotDataXferFromSubnet		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.8
This attribute displays the number of subnet packets discarded when data transfer is suspended in Vc recovery.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcFrmLossTimeouts		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.9
This attribute displays the number of lost frame timer expiries. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcOoSeqByteCntExceeded		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.10
This attribute displays the number times that the out of sequence byte threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcPeakOoSeqPktCount		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.11
This attribute displays the frame relay peak packet count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcPeakOoSeqFrmForwarded		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.12
This attribute displays the frame relay peak size of the sequence packet queue. The subnet may deliver packets out-of- sequenced. These packets are then queued in an out-of-sequenced queue, waiting for a packet with the expected sequence number to come. When that packet arrives, this attribute records the maximum number of packets that were out-of-sequenced, but now have become in-sequenced. The statistics is used to measure expected queue size due to normal subnet packet disorder (not due to subnet packet discard). Current implementation also uses this statistics to set a maximum size for the out-of-sequenced queue.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcSendSequenceNumber		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.13
This attribute displays the Vc internal packet's send sequence number. Note that a 'packet' in this context, may be either a user data packet, or an OAM frame.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcPktRetryTimeouts		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.15
This attribute displays the number of packets which have retransmission time-outs. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcPeakRetryQueueSize		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.16
This attribute displays the peak size of retransmission queue. This attribute is used as an indicator of the acknowledgment behavior across the subnet. Records the largest body of unacknowledged packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcSubnetRecoveries		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.17
This attribute displays the number of successful Vc recovery attempts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

frNniDlciVcOoSeqPktCntExceeded		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.19
This attribute displays the number times that the out of sequence packet threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

frNniDlciVcPeakOoSeqByteCount		1.3.6.1.4.1.562.2.4.1.70.5.3.12.1.20
This attribute displays the frame relay peak byte count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..50000

frNniDlciVcDmepTable		1.3.6.1.4.1.562.2.4.1.70.5.3.417
This attribute displays the data path used by the connection. Data path is provisioned in Dna and DirectCall components. If the connection is using dprsOnly data path, this attribute is empty. If the connection is using dprsMcsOnly or dprsMcsFirst data path, this attribute displays component name of the dprsMcsEndPoint.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciVcDmepEntry

frNniDlciVcDmepEntry		1.3.6.1.4.1.562.2.4.1.70.5.3.417.1
An entry in the frNniDlciVcDmepTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciVcDmepEntry

frNniDlciVcDmepValue		1.3.6.1.4.1.562.2.4.1.70.5.3.417.1.1
This variable represents both the value and the index for the frNniDlciVcDmepTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowPointer

frNniDlciSp		1.3.6.1.4.1.562.2.4.1.70.5.4
OBJECT IDENTIFIER

frNniDlciSpRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.5.4.1
This entry controls the addition and deletion of frNniDlciSp components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciSpRowStatusEntry

frNniDlciSpRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.5.4.1.1
A single entry in the table represents a single frNniDlciSp component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciSpRowStatusEntry

frNniDlciSpRowStatus		1.3.6.1.4.1.562.2.4.1.70.5.4.1.1.1
This variable is used as the basis for SNMP naming of frNniDlciSp components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

frNniDlciSpComponentName		1.3.6.1.4.1.562.2.4.1.70.5.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDlciSpStorageType		1.3.6.1.4.1.562.2.4.1.70.5.4.1.1.4
This variable represents the storage type value for the frNniDlciSp tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDlciSpIndex		1.3.6.1.4.1.562.2.4.1.70.5.4.1.1.10
This variable represents the index for the frNniDlciSp tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniDlciSpParmsTable		1.3.6.1.4.1.562.2.4.1.70.5.4.11
This group contains the provisionable attributes for the Data Link Connection Identifier. These attributes reflect the service parameters specific to this instance of DLCI . The congestion control attributes in this group are defined in T1.606 Addendum 1.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciSpParmsEntry

frNniDlciSpParmsEntry		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1
An entry in the frNniDlciSpParmsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciSpParmsEntry

frNniDlciSpMaximumFrameSize		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.1
This attribute specifies the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Vendor Forum Specification.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	1..8187

frNniDlciSpRateEnforcement		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.2
This attribute specifies whether rate enforcement is in effect for this user Data Link Connection on this Frame Relay interface. Turning on rate enforcement means that CIR and DE=1 traffic will be measured and enforced. Turning off rate enforcement means that all frames from the user will be accepted and no modifications to the frame with respect to the DE bit will be made.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniDlciSpCommittedInformationRate		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.3
This attribute specifies the committed information rate (CIR) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (t) that is determined internally based on CIR and the committed burst size (Bc). An exception to this occurs when CIR is provisioned to be zero, in which case the measurement interval (t) must be provisioned explicitly. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, Bc must also be 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Gauge32	0..50000000

frNniDlciSpCommittedBurstSize		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.4
This attribute specifies the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, cir must also be 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Gauge32	0..50000000

frNniDlciSpExcessBurstSize		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.5
This attribute specifies the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. CIR, Bc, and Be cannot all be zero when rateEnforcement is on.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Gauge32	0..50000000

frNniDlciSpMeasurementInterval		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.6
When cir and bc are zero and rateEnforcement is on, this attribute must be provisioned to specify the time interval (in milliseconds) over which rates and burst sizes are measured. When cir and bc are non-zero, the time interval is internally calculated and is not shown. In that situation, this field is ignored, and is not representative of the time interval. This attribute is ignored when rateEnforcement is off, or when cir and bc are non-zero. If rateEnforcement is on and both cir and bc are zero, this field must be non-zero.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..25500

frNniDlciSpRateAdaptation		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.7
This attribute specifies whether rate adaptation is in effect for this user Data Link Connection on this Frame Relay interface. Rate adaptation is a feature that, in periods of congestion, adapts the rate at which the user is allowed to send data into the network to that which the network is able to handle at that time. This pro-active measure of handling congestion optimizes network resources by causing the ingress to discard frames that would otherwise be discarded in the network. If this attribute is set to on, then, at the onset of congestion, the excess information rate (EIR) is reduced to a very low rate. If congestion persists, then the allowed CIR is reduced geometrically by 25% of the current value at that time. The minimum to which CIR can be reduced is 1/16th (6.25%) of the provisioned value. As congestion alleviates, CIR is increased linearly by 6.25% of the provisioned value specified in committedInformationRate. If set to eirOnly, then rate adaptation will only apply to the excess information rate (EIR). At the onset of congestion, the allowed EIR is reduced by 25% of its provisioned value. If congestion persists, EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. If set to cirProportionate, then rate adaptation will also only apply to the excess information rate (EIR). At the onset of congestion the initial allowed EIR is set to a multiple of the provisioned CIR. If congestion persists, the allowed EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. Note that the allowed EIR may be set higher than the provisioned EIR, since it is calculated initially using another parameter, the provisioned CIR. If the allowed EIR at the moment is higher than the provisioned EIR, then the provisioned EIR is used instead. This attribute can only be set to on eirOnly or cirProportionate if rateEnforcement is turned on.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), on(1), eirOnly(2), cirProportionate(3)

frNniDlciSpAccounting		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.8
This attribute specifies whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the accountingOn bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniDlciSpRaSensitivity		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.9
This attribute specifies the sensitivity of the rate adaptation system. A higher number indicates a higher sensitivity and therefore a quicker reaction time to network conditions. A quicker reaction time allows the network to discard frames at the access and protect network resources, but can lead to false alarms and a greater fluctuation of the allowed rate. A higher setting therefore tends to favour the protection of the network over the allowed throughput of the user. A lower number indicates a lower sensitivity and therefore a slower reaction to network conditions. A slower reaction time results in a greater amount of user traffic allowed into the network, but can lead to a waste of network bandwidth since the traffic may be discarded at the congested resource. A lower setting therefore tends to favour the allowed throughput of the user over the protection of the network. This attribute is applicable for adapting EIR when rateAdaptation is eirOnly or cirProportionate, or CIR when rateAdaptation is on. This attribute is ignored if rateAdaptation is turned off.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	1..20

frNniDlciSpUpdateBCI		1.3.6.1.4.1.562.2.4.1.70.5.4.11.1.10
This attribute specifies whether internal Backward Congestion Indication (BCI) bits will report congestion external to the Passport network, as communicated through incoming BECN bits. If updateBCI is set to on, then BCI bits for incoming frames will be set if the BECN on the frame is set. If updatBCI is set to off, then incoming BECN bits will have no effect. Setting updateBCI on for a DLCI means that the remote end of the DLCI, which is specified by the remotedna and remotedlci attributes of the dc component of the dlci, may perform Rate Adaptation using the flow of incoming BECN bits, in addition to internal Passport congestion management systems. If the rateAdaptation attribute of the remote dlci is provisioned as eirOnly, cirProportionate, or on, then congestion from another network connected to a Passport network may trigger dynamic congestion management. If the rateAdaptation attribute of the remote dlci is provisioned to off, then the setting of updateBCI attribute here will have no effect..
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), on(1)

frNniDlciLb		1.3.6.1.4.1.562.2.4.1.70.5.5
OBJECT IDENTIFIER

frNniDlciLbRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.5.5.1
This entry controls the addition and deletion of frNniDlciLb components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciLbRowStatusEntry

frNniDlciLbRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.5.5.1.1
A single entry in the table represents a single frNniDlciLb component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciLbRowStatusEntry

frNniDlciLbRowStatus		1.3.6.1.4.1.562.2.4.1.70.5.5.1.1.1
This variable is used as the basis for SNMP naming of frNniDlciLb components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

frNniDlciLbComponentName		1.3.6.1.4.1.562.2.4.1.70.5.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniDlciLbStorageType		1.3.6.1.4.1.562.2.4.1.70.5.5.1.1.4
This variable represents the storage type value for the frNniDlciLb tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniDlciLbIndex		1.3.6.1.4.1.562.2.4.1.70.5.5.1.1.10
This variable represents the index for the frNniDlciLb tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniDlciLbStatsTable		1.3.6.1.4.1.562.2.4.1.70.5.5.10
This group contains all the statistics for the data loopback tool.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniDlciLbStatsEntry

frNniDlciLbStatsEntry		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1
An entry in the frNniDlciLbStatsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniDlciLbStatsEntry

frNniDlciLbLocalTotalFrm		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.1
This attribute records the number of frames looped back to the link since loopback was last started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbLocalTotalBytes		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.2
This attribute records the number of bytes looped back to the link since loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbLocalFecnFrm		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.3
This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the link since the loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbLocalBecnFrm		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.4
This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the link since the loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbLocalDeFrm		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.5
This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbLocalDeBytes		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.6
This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbRemoteTotalFrm		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.7
This attribute records the number of frames looped back to the subnet since loopback was last started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbRemoteTotalBytes		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.8
This attribute records the number of bytes looped back to the subnet since loopback was last started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbRemoteFecnFrm		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.9
This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbRemoteBecnFrm		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.10
This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbRemoteDeFrm		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.13
This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniDlciLbRemoteDeBytes		1.3.6.1.4.1.562.2.4.1.70.5.5.10.1.14
This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniVFramer		1.3.6.1.4.1.562.2.4.1.70.6
OBJECT IDENTIFIER

frNniVFramerRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.6.1
This entry controls the addition and deletion of frNniVFramer components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniVFramerRowStatusEntry

frNniVFramerRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.6.1.1
A single entry in the table represents a single frNniVFramer component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniVFramerRowStatusEntry

frNniVFramerRowStatus		1.3.6.1.4.1.562.2.4.1.70.6.1.1.1
This variable is used as the basis for SNMP naming of frNniVFramer components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniVFramerComponentName		1.3.6.1.4.1.562.2.4.1.70.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniVFramerStorageType		1.3.6.1.4.1.562.2.4.1.70.6.1.1.4
This variable represents the storage type value for the frNniVFramer tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniVFramerIndex		1.3.6.1.4.1.562.2.4.1.70.6.1.1.10
This variable represents the index for the frNniVFramer tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniVFramerProvTable		1.3.6.1.4.1.562.2.4.1.70.6.10
This group contains provisionable attributes for the VirtualFramer component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniVFramerProvEntry

frNniVFramerProvEntry		1.3.6.1.4.1.562.2.4.1.70.6.10.1
An entry in the frNniVFramerProvTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniVFramerProvEntry

frNniVFramerOtherVirtualFramer		1.3.6.1.4.1.562.2.4.1.70.6.10.1.1
This attribute specifies the other VirtualFramer to which the service is linked, for example, FrUni/n VirtualFramer, FrDte/n VirtualFramer.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Link

frNniVFramerLogicalProcessor		1.3.6.1.4.1.562.2.4.1.70.6.10.1.2
This attribute specifies the logical processor on which the service component will reside.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Link

frNniVFramerStateTable		1.3.6.1.4.1.562.2.4.1.70.6.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniVFramerStateEntry

frNniVFramerStateEntry		1.3.6.1.4.1.562.2.4.1.70.6.11.1
An entry in the frNniVFramerStateTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniVFramerStateEntry

frNniVFramerAdminState		1.3.6.1.4.1.562.2.4.1.70.6.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	locked(0), unlocked(1), shuttingDown(2)

frNniVFramerOperationalState		1.3.6.1.4.1.562.2.4.1.70.6.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

frNniVFramerUsageState		1.3.6.1.4.1.562.2.4.1.70.6.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(0), active(1), busy(2)

frNniVFramerStatsTable		1.3.6.1.4.1.562.2.4.1.70.6.12
This group contains the operational statistics data for a VirtualFramer component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniVFramerStatsEntry

frNniVFramerStatsEntry		1.3.6.1.4.1.562.2.4.1.70.6.12.1
An entry in the frNniVFramerStatsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniVFramerStatsEntry

frNniVFramerFrmToOtherVFramer		1.3.6.1.4.1.562.2.4.1.70.6.12.1.2
This attribute counts the frames transmitted to the otherVirtualFramer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	PassportCounter64

frNniVFramerFrmFromOtherVFramer		1.3.6.1.4.1.562.2.4.1.70.6.12.1.3
This attribute counts the frames received from the otherVirtualFramer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	PassportCounter64

frNniVFramerOctetFromOtherVFramer		1.3.6.1.4.1.562.2.4.1.70.6.12.1.5
This attribute counts the octets received from the otherVirtualFramer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	PassportCounter64

frNniLts		1.3.6.1.4.1.562.2.4.1.70.9
OBJECT IDENTIFIER

frNniLtsRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.9.1
This entry controls the addition and deletion of frNniLts components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsRowStatusEntry

frNniLtsRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.9.1.1
A single entry in the table represents a single frNniLts component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsRowStatusEntry

frNniLtsRowStatus		1.3.6.1.4.1.562.2.4.1.70.9.1.1.1
This variable is used as the basis for SNMP naming of frNniLts components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniLtsComponentName		1.3.6.1.4.1.562.2.4.1.70.9.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniLtsStorageType		1.3.6.1.4.1.562.2.4.1.70.9.1.1.4
This variable represents the storage type value for the frNniLts tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniLtsIndex		1.3.6.1.4.1.562.2.4.1.70.9.1.1.10
This variable represents the index for the frNniLts tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

frNniLtsSetupTable		1.3.6.1.4.1.562.2.4.1.70.9.10
This attribute group contains the parameters used to configure the behavior of the Frame Relay Load Test System.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsSetupEntry

frNniLtsSetupEntry		1.3.6.1.4.1.562.2.4.1.70.9.10.1
An entry in the frNniLtsSetupTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsSetupEntry

frNniLtsDuration		1.3.6.1.4.1.562.2.4.1.70.9.10.1.200
This attribute specifies the duration of the test in milliseconds. The test will run until the duration expires or the STOP command is issued. A value of 0 is used to indicate infinity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniLtsAlgorithm		1.3.6.1.4.1.562.2.4.1.70.9.10.1.201
This attribute specifies which algorithm is used to generate the frames. ContinuousBurst This mode of traffic generation creates traffic at the maximum rate possible until all of the frames have been sent. The generator then waits until the end of the timeInterval to begin again. IntervalBurst This algorithm attempts to generate 10 ms bursts of burstSize frames. It will generate as many of the burstSize frames as it can per sub-interval. DelayedBurst This algorithm generates bursts of burstSize frames separated by 10 ms delays. FixedBurst This aglorithm is similar to IntervalBurst, except a fixed burst size of 12 frames is used. delayMeasurement This algorithm is used to measure delay. The specified number of frames in the indicated pattern are generated, one at a time, with a maximum wait of maxDelay before sending the next frame. This algorithm is not implemented yet.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	continousBurst(0), intervalBurst(1), delayBurst(2), fixedBurst(3)

frNniLtsBurstSize		1.3.6.1.4.1.562.2.4.1.70.9.10.1.204
This attribute specifies the number of frames per burst under the delayedBurst and intervalBurst algorithms.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	1..250

frNniLtsTimeInterval		1.3.6.1.4.1.562.2.4.1.70.9.10.1.205
This attribute specifies the time interval to the specified number of seconds. Granuality is in centiseconds. Maximum is 1 minute.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	1..60000

frNniLtsStateTable		1.3.6.1.4.1.562.2.4.1.70.9.11
This group contains the operation statistics of the load generator.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsStateEntry

frNniLtsStateEntry		1.3.6.1.4.1.562.2.4.1.70.9.11.1
An entry in the frNniLtsStateTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsStateEntry

frNniLtsGeneratorState		1.3.6.1.4.1.562.2.4.1.70.9.11.1.200
This attribute indicates whether the Lts is generating traffic.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	stopped(0), running(1)

frNniLtsCycleIncomplete		1.3.6.1.4.1.562.2.4.1.70.9.11.1.201
This attribute indicates whether the time required to generate all of the enabled patterns is more than timeInterval by a true value. Otherwise, this flag is set to false. Default is True.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	false(0), true(1)

frNniLtsLastActiveInterval		1.3.6.1.4.1.562.2.4.1.70.9.11.1.202
This attribute indicates the actual time it took to generate all of the enabled patterns in the last cycle. If cycleIncomplete is true, this value should be zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniLtsLoad		1.3.6.1.4.1.562.2.4.1.70.9.11.1.204
This attribute indicates the load being generated. This value represents that calculated using the set number of ticks. The actual burstTimeInterval may differ. One entire cycle of the patterns is completed in activeInterval and thus most of the load may be concentrated early in the set interval.
Status: mandatory	Access: read-only
OBJECT-TYPE
	FixedPoint3	0..4294967295

frNniLtsElapsedGenerationTime		1.3.6.1.4.1.562.2.4.1.70.9.11.1.205
This attribute indicates how many milliseconds have elapsed since the start of this test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniLtsResultsTable		1.3.6.1.4.1.562.2.4.1.70.9.12
This group contains the frame counting attributes for the LTS component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsResultsEntry

frNniLtsResultsEntry		1.3.6.1.4.1.562.2.4.1.70.9.12.1
An entry in the frNniLtsResultsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsResultsEntry

frNniLtsFramesTx		1.3.6.1.4.1.562.2.4.1.70.9.12.1.200
This attribute specifies the number of frames send to the network since the last time these statistics were cleared. This is similar to the framesToIf attribute of the FRAMER component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

frNniLtsBytesTx		1.3.6.1.4.1.562.2.4.1.70.9.12.1.204
This attribute indicates the number of bytes sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniLtsBitRateTx		1.3.6.1.4.1.562.2.4.1.70.9.12.1.208
This attribute indicates the bit rate being sent to the link. It should only differ from the load if the burstTimeInterval would be >= the timeInterval or burstSize frames cannot be generated in 10ms (intervalBurst algorithm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	FixedPoint3	0..4294967295

frNniLtsFrameRateTx		1.3.6.1.4.1.562.2.4.1.70.9.12.1.209
This attribute indicates the frame rate being sent to the link. It is calculated using the number of frames sent to the link in one cycle of the patterns.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniLtsPat		1.3.6.1.4.1.562.2.4.1.70.9.2
OBJECT IDENTIFIER

frNniLtsPatRowStatusTable		1.3.6.1.4.1.562.2.4.1.70.9.2.1
This entry controls the addition and deletion of frNniLtsPat components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsPatRowStatusEntry

frNniLtsPatRowStatusEntry		1.3.6.1.4.1.562.2.4.1.70.9.2.1.1
A single entry in the table represents a single frNniLtsPat component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsPatRowStatusEntry

frNniLtsPatRowStatus		1.3.6.1.4.1.562.2.4.1.70.9.2.1.1.1
This variable is used as the basis for SNMP naming of frNniLtsPat components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

frNniLtsPatComponentName		1.3.6.1.4.1.562.2.4.1.70.9.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

frNniLtsPatStorageType		1.3.6.1.4.1.562.2.4.1.70.9.2.1.1.4
This variable represents the storage type value for the frNniLtsPat tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

frNniLtsPatIndex		1.3.6.1.4.1.562.2.4.1.70.9.2.1.1.10
This variable represents the index for the frNniLtsPat tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	0..29

frNniLtsPatDefaultsTable		1.3.6.1.4.1.562.2.4.1.70.9.2.10
This attribute group contains the specifications of the pattern.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsPatDefaultsEntry

frNniLtsPatDefaultsEntry		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1
An entry in the frNniLtsPatDefaultsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsPatDefaultsEntry

frNniLtsPatDefaultDlci		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.200
This attribute specifies for which dlci (on the local end) the frames are destined.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	16..1007

frNniLtsPatDefaultNumFrames		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.201
This attribute specifies the number of frames in this pattern. This is the number of frames of this type which will be generated in one timeInterval.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniLtsPatDefaultDataSize		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.202
This attribute specifies the payload size of each frame in bytes. This is in excess to the header.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..8200

frNniLtsPatDefaultHeaderBits		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.203
This attribute specifies whether the following bits are on/off in the header of each frame. The following bits can be set: BeCn, C/R, De, FeCn Description of bits: becn(0) fecn(1) cr(2) de(3)
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniLtsPatDefaultHeaderLength		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.204
This attribute specifies the size of the frame relay header in bytes. Passport currently only supports a 2-byte header.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0 | 2..4

frNniLtsPatDefaultEABits		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.205
This attribute specifies how the address field extension bits are set in the frame header. Consider the value to be a four bit binary number. For example, 4 = 0100. Only the first headerLength bits are used. For instance, suppose headerLength is 3, then the appropriate EABits is 2, or 0010. This attribute can be used to create a header of length greater than two bytes or to specify incorrect EABits in the header.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Hex	0..15

frNniLtsPatDefaultPayloadPattern		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.206
This attribute specifies the payload of each frame. The value specified is in hexadecimal, where every two digits represent a byte. A maximum of 24 digits (12 bytes) may be set, after which the pattern will repeat in the payload (depending on repeatPattern attribute). NOTE: If a RFC 1490 header is specified, via the 1490Header attribute, the specified pattern will begin following the header (i.e. at the 9th byte in the payload).
Status: mandatory	Access: read-write
OBJECT-TYPE
	HexString	Size(1..12)

frNniLtsPatDefaultRfc1490Header		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.207
This attribute specifies the appropriate RFC 1490 encapsulated header of the frame. A value of 0 indicates no 1490 header. NOTE: This header resides in the first 8 bytes of the payload. If the specified value is non-zero, then the payload pattern provisioned will begin at the 9th byte.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), n16(16), n17(17), none(18)

frNniLtsPatDefaultUseBadLrc		1.3.6.1.4.1.562.2.4.1.70.9.2.10.1.208
This attribute specifies whether the frames from this pattern are to have a bad LRC prior to being sent to the framer. The LRC is checked while the frame is being put onto the link and the failure should cause an abort frame to be sent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniLtsPatSetupTable		1.3.6.1.4.1.562.2.4.1.70.9.2.11
This attribute group contains the specifications of the pattern.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsPatSetupEntry

frNniLtsPatSetupEntry		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1
An entry in the frNniLtsPatSetupTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsPatSetupEntry

frNniLtsPatDlci		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.200
This attribute specifies for which dlci (on the local end) the frames are destined.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	16..1007

frNniLtsPatNumFrames		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.201
This attribute specifies the number of frames in this pattern. This is the number of frames of this type which will be generated in one timeInterval.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

frNniLtsPatDataSize		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.202
This attribute specifies the payload size of each frame in bytes. This is in excess to the header.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..8200

frNniLtsPatHeaderBits		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.203
This attribute specifies whether the following bits are on/off in the header of each frame. The following bits can be set: BeCn, C/R, De, FeCn Description of bits: becn(0) fecn(1) cr(2) de(3)
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

frNniLtsPatHeaderLength		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.204
This attribute specifies the size of the frame relay header in bytes. Passport currently only supports a 2-byte header. Valid values are 0, 2, 3, 4. 0 indicates to use no header. That is, the frame will start with either the payload or rfc1490 header.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0 | 2..4

frNniLtsPatEaBits		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.205
This attribute specifies how the address field extension bits are set in the frame header. Consider the value to be a four bit binary number. For example, 4 = 0100. Only the first headerLength bits are used. For instance, suppose headerLength is 3, then the appropriate eaBits is 2, or 0010. This attribute can be used to create a header of length greater than two bytes or to specify incorrect eaBits in the header.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Hex	0..15

frNniLtsPatPayloadPattern		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.206
This attribute specifies the payload of each frame. The value specified is in hexadecimal, where every two digits represent a byte. A maximum of 24 digits (12 bytes) may be set, after which the pattern will repeat in the payload (depending on repeatPattern attribute). NOTE: If a RFC 1490 header is specified, via the 1490Header attribute, the specified pattern will begin following the header (i.e. at the 9th byte in the payload).
Status: mandatory	Access: read-write
OBJECT-TYPE
	HexString	Size(1..12)

frNniLtsPatRfc1490Header		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.207
This attribute specifies the appropriate RFC 1490 encapsulated header of the frame. A value of 0 indicates no 1490 header. NOTE: This header resides in the first 8 bytes of the payload. If the specified value is non-zero, then the payload pattern provisioned will begin at the 9th byte.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), n16(16), n17(17), none(18)

frNniLtsPatUseBadLrc		1.3.6.1.4.1.562.2.4.1.70.9.2.11.1.208
This attribute specifies whether the frames from this pattern are to have a bad LRC prior to being sent to the framer. The LRC is checked while the frame is being put onto the link and the failure should cause an abort frame to be sent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

frNniLtsPatOpDataTable		1.3.6.1.4.1.562.2.4.1.70.9.2.12
This group contains the operational attributes which allow changing the pattern outside of provisioning mode.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsPatOpDataEntry

frNniLtsPatOpDataEntry		1.3.6.1.4.1.562.2.4.1.70.9.2.12.1
An entry in the frNniLtsPatOpDataTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsPatOpDataEntry

frNniLtsPatFramePattern		1.3.6.1.4.1.562.2.4.1.70.9.2.12.1.200
This attribute displays the first 20 to 24 bytes of the frame payload, depending on the frame relay header size selected. This attribute represents the frame if it were at least 20 to 24 bytes in size. That is, the actual frame may be smaller.
Status: mandatory	Access: read-only
OBJECT-TYPE
	HexString	Size(20..24)

frNniLtsPatHdlcBitsInserted		1.3.6.1.4.1.562.2.4.1.70.9.2.12.1.201
This attribute displays how many times a zero bit will be inserted after 5 consecutive 1 bits when a frame from this pattern is sent out.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

frNniLtsPatOpStateTable		1.3.6.1.4.1.562.2.4.1.70.9.2.13
This group contains the attributes containing the operational statistics of the pattern.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrNniLtsPatOpStateEntry

frNniLtsPatOpStateEntry		1.3.6.1.4.1.562.2.4.1.70.9.2.13.1
An entry in the frNniLtsPatOpStateTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrNniLtsPatOpStateEntry

frNniLtsPatLoad		1.3.6.1.4.1.562.2.4.1.70.9.2.13.1.200
This attribute indicates the load due to this particular pattern. The loads associated with all of the provisioned patterns are summed to arrive at the FrLts load.
Status: mandatory	Access: read-only
OBJECT-TYPE
	FixedPoint3	0..4294967295

frNniLtsPatStatus		1.3.6.1.4.1.562.2.4.1.70.9.2.13.1.201
This attributes specifies the administrative state of the pattern. A disabled pattern will not be generated, although it can still be triggered.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(0), disabled(1)

frameRelayNniGroup		1.3.6.1.4.1.562.2.4.2.23.1
OBJECT IDENTIFIER

frameRelayNniGroupBE		1.3.6.1.4.1.562.2.4.2.23.1.5
OBJECT IDENTIFIER

frameRelayNniGroupBE01		1.3.6.1.4.1.562.2.4.2.23.1.5.2
OBJECT IDENTIFIER

frameRelayNniGroupBE01A		1.3.6.1.4.1.562.2.4.2.23.1.5.2.2
OBJECT IDENTIFIER

frameRelayNniCapabilities		1.3.6.1.4.1.562.2.4.2.23.3
OBJECT IDENTIFIER

frameRelayNniCapabilitiesBE		1.3.6.1.4.1.562.2.4.2.23.3.5
OBJECT IDENTIFIER

frameRelayNniCapabilitiesBE01		1.3.6.1.4.1.562.2.4.2.23.3.5.2
OBJECT IDENTIFIER

frameRelayNniCapabilitiesBE01A		1.3.6.1.4.1.562.2.4.2.23.3.5.2.2
OBJECT IDENTIFIER