NNCEXTPVC-MIB

Imported modules

SNMPv2-SMI	SNMPv2-TC	IF-MIB
SNMPv2-CONF	NNCGNI0001-SMI

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
TEXTUAL-CONVENTION	RowStatus	InterfaceIndex
MODULE-COMPLIANCE	OBJECT-GROUP	nncExtensions

Defined Types

NncCrPvpcTableEntry
SEQUENCE
	nncCrPvpcSrcIfIndex	InterfaceIndex
	nncCrPvpcSrcVpi	INTEGER
	nncCrPvpcDstIfIndex	InterfaceIndex
	nncCrPvpcDstVpi	INTEGER
	nncCrPvpcCastType	INTEGER
	nncCrPvpcFwdServiceCategory	INTEGER
	nncCrPvpcBwdServiceCategory	INTEGER
	nncCrPvpcFwdAbrDynTrfcIcr	INTEGER
	nncCrPvpcFwdAbrDynTrfcRif	INTEGER
	nncCrPvpcFwdAbrDynTrfcRdf	INTEGER
	nncCrPvpcBwdAbrDynTrfcIcr	INTEGER
	nncCrPvpcBwdAbrDynTrfcRif	INTEGER
	nncCrPvpcBwdAbrDynTrfcRdf	INTEGER
	nncCrPvpcSrcBillingFlag	INTEGER
	nncCrPvpcDstBillingFlag	INTEGER
	nncCrPvpcFwdTmTrafficDescriptor	INTEGER
	nncCrPvpcFwdTmPolicingOption	INTEGER
	nncCrPvpcFwdTmBucketOneRate	INTEGER
	nncCrPvpcFwdTmBucketOneCdvt	INTEGER
	nncCrPvpcFwdTmBucketTwoRate	INTEGER
	nncCrPvpcFwdTmBucketTwoMbs	INTEGER
	nncCrPvpcFwdTmCdv	INTEGER
	nncCrPvpcFwdTmClr	INTEGER
	nncCrPvpcBwdTmTrafficDescriptor	INTEGER
	nncCrPvpcBwdTmPolicingOption	INTEGER
	nncCrPvpcBwdTmBucketOneRate	INTEGER
	nncCrPvpcBwdTmBucketOneCdvt	INTEGER
	nncCrPvpcBwdTmBucketTwoRate	INTEGER
	nncCrPvpcBwdTmBucketTwoMbs	INTEGER
	nncCrPvpcBwdTmCdv	INTEGER
	nncCrPvpcBwdTmClr	INTEGER
	nncCrPvpcSrcAlsConfig	INTEGER
	nncCrPvpcDstAlsConfig	INTEGER
	nncCrPvpcCreator	INTEGER
	nncCrPvpcRowStatus	RowStatus

NncCrPvccTableEntry
SEQUENCE
	nncCrPvccSrcIfIndex	InterfaceIndex
	nncCrPvccSrcVpi	INTEGER
	nncCrPvccSrcVci	INTEGER
	nncCrPvccDstIfIndex	InterfaceIndex
	nncCrPvccDstVpi	INTEGER
	nncCrPvccDstVci	INTEGER
	nncCrPvccCastType	INTEGER
	nncCrPvccFwdServiceCategory	INTEGER
	nncCrPvccBwdServiceCategory	INTEGER
	nncCrPvccFwdAbrDynTrfcIcr	INTEGER
	nncCrPvccFwdAbrDynTrfcRif	INTEGER
	nncCrPvccFwdAbrDynTrfcRdf	INTEGER
	nncCrPvccBwdAbrDynTrfcIcr	INTEGER
	nncCrPvccBwdAbrDynTrfcRif	INTEGER
	nncCrPvccBwdAbrDynTrfcRdf	INTEGER
	nncCrPvccSrcBillingFlag	INTEGER
	nncCrPvccDstBillingFlag	INTEGER
	nncCrPvccFwdTmTrafficDescriptor	INTEGER
	nncCrPvccFwdTmPolicingOption	INTEGER
	nncCrPvccFwdTmBucketOneRate	INTEGER
	nncCrPvccFwdTmBucketOneCdvt	INTEGER
	nncCrPvccFwdTmBucketTwoRate	INTEGER
	nncCrPvccFwdTmBucketTwoMbs	INTEGER
	nncCrPvccFwdTmCdv	INTEGER
	nncCrPvccFwdTmClr	INTEGER
	nncCrPvccFwdTmFrameDiscard	INTEGER
	nncCrPvccBwdTmTrafficDescriptor	INTEGER
	nncCrPvccBwdTmPolicingOption	INTEGER
	nncCrPvccBwdTmBucketOneRate	INTEGER
	nncCrPvccBwdTmBucketOneCdvt	INTEGER
	nncCrPvccBwdTmBucketTwoRate	INTEGER
	nncCrPvccBwdTmBucketTwoMbs	INTEGER
	nncCrPvccBwdTmCdv	INTEGER
	nncCrPvccBwdTmClr	INTEGER
	nncCrPvccBwdTmFrameDiscard	INTEGER
	nncCrPvccSrcAlsConfig	INTEGER
	nncCrPvccDstAlsConfig	INTEGER
	nncCrPvccCreator	INTEGER
	nncCrPvccRowStatus	RowStatus

Defined Values

nncExtPvc		1.3.6.1.4.1.123.3.79
This module contains Alcatel's proprietary MIB definition for managing point-to-point and point-to-multipoint Permanent Virtual Connections (PVCs). The MIB supports the creation, modification, query and deletion of PVCs (Permanent Virtual Connections) on Cell Relay endpoints, both Permanent Virtual Path Connection (PVPC) and Permanent Virtual Channel Connection (PVCC) are supported. PVPCs are defined by nncCrPvpcTable and PVCCs are defined by nncCrPvccTable. PVPCs or PVCC's connecting different endpoint types, CR to FR, FR to CR, CR to CE, CE to CR, CE to FR or FR to CE are not suppported at this point. Resource connections such as Signalling, PNNI, ILMI and CPSS are also not supported. PVCs can be created by one of two ways: using rowStats as 'createAndGo' or using rowStatus as 'createAndWait'+'active'. In some cases, to create a PVC via this table requires two SET-REQs, because one SET-REQ PDU cannot fit all required objects. In these cases, the rowStatus is set to createAndWait(5) for the first 1 SET-REQ and set to active(1) for the last SET-REQ. In some cases, all required MIB objects can fit in one SET-REQ PDU. In these cases the rowStatus should be set to createAndGo(4) To delete a PVC, the SNMP manager should set rowStatus of the PVC instance to 'destroy'. Each PVC is modeled as set of entries in the PVC table. A point- to-point PVC is modeled as one entry; a point-to-multipoint (N leafs) is modeled as N entries in this table. The N entries of a point-to- multipoint PVC shares the same source end point. Some abreviations: abr/ABR/Abr: Available Bit Rate Bwd: Backward. For traffice descriptors from destination end point to source end point cbr/CBR/Cbr: Constant Bit Rate Dst: Dstination end point Fwd: Forward. For traffic descriptors from source end point to destination end point nt-vbr/ntvbr/NT-VBR: Non-Real-Time Variable Bit Rate p2p: Point-to-Point p2mp: Point-to-Multipoint Src: Source end point Targ: Target. For the destination end point info in source end point table ubr/UBR/Ubr: Unspecified Bit Rate VCI/Vci/vci: Virtual channel identifier VCL/Vcl/vcl: Virtual channel link VPI/Vpi/vpi: Virtual path identifier VPL/Vpl/Vpl: Virtual path link
MODULE-IDENTITY

nncExtPvcObjects		1.3.6.1.4.1.123.3.79.1
OBJECT IDENTIFIER

nncExtPvcGroups		1.3.6.1.4.1.123.3.79.3
OBJECT IDENTIFIER

nncExtPvcCompliances		1.3.6.1.4.1.123.3.79.4
OBJECT IDENTIFIER

nncCrPvpcTable		1.3.6.1.4.1.123.3.79.1.1
nncCrPvpcTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query PVC connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NncCrPvpcTableEntry

nncCrPvpcTableEntry		1.3.6.1.4.1.123.3.79.1.1.1
An entry of nncCrPvpcTable
Status: current	Access: not-accessible
OBJECT-TYPE
	NncCrPvpcTableEntry

nncCrPvpcSrcIfIndex		1.3.6.1.4.1.123.3.79.1.1.1.1
This object contains the ifIndex value for the source endpoint
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

nncCrPvpcSrcVpi		1.3.6.1.4.1.123.3.79.1.1.1.2
This object contains the VPI value for the source endpoint.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

nncCrPvpcDstIfIndex		1.3.6.1.4.1.123.3.79.1.1.1.3
This object contains the ifIndex value for the destination endpoint
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

nncCrPvpcDstVpi		1.3.6.1.4.1.123.3.79.1.1.1.4
This object contains the VPI value for the destination endpoint.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

nncCrPvpcCastType		1.3.6.1.4.1.123.3.79.1.1.1.5
This object is used to indicate whether the PVPC is point-to-point or point-to-multipoint
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	p2p(1), p2mp(2)

nncCrPvpcFwdServiceCategory		1.3.6.1.4.1.123.3.79.1.1.1.6
This object is used to set the traffic service category from source endpoint to destination endpoint. This object is dependent on the value specified in nncCrPvpcFwdTmTrafficDescripton object
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	cbr(1), nrtvbr(2), abr(3), ubr(4), rtvbr(6)

nncCrPvpcBwdServiceCategory		1.3.6.1.4.1.123.3.79.1.1.1.7
This object is used to set the traffic service category from destination endpoint to source endpoint. This object is dependent on the value specified in nncCrPvpcBwdTmTrafficDescripton object
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	cbr(1), nrtvbr(2), abr(3), ubr(4), rtvbr(6)

nncCrPvpcFwdAbrDynTrfcIcr		1.3.6.1.4.1.123.3.79.1.1.1.8
ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvpcFwdAbrDynTrfcRif		1.3.6.1.4.1.123.3.79.1.1.1.9
ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..9

nncCrPvpcFwdAbrDynTrfcRdf		1.3.6.1.4.1.123.3.79.1.1.1.10
ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..9

nncCrPvpcBwdAbrDynTrfcIcr		1.3.6.1.4.1.123.3.79.1.1.1.11
ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvpcBwdAbrDynTrfcRif		1.3.6.1.4.1.123.3.79.1.1.1.12
ABR traffic Rate Increase Factor for the destination endpoint. Value is expressed as the -power of 2. Range: 0 - 9
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..9

nncCrPvpcBwdAbrDynTrfcRdf		1.3.6.1.4.1.123.3.79.1.1.1.13
ABR traffic Rate Decrease Factor descriptor for the destination endpoint. Value is expressed as the -power of 2 Range: 0 - 9
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..9

nncCrPvpcSrcBillingFlag		1.3.6.1.4.1.123.3.79.1.1.1.14
Billing Configuration for the source endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvpcDstBillingFlag		1.3.6.1.4.1.123.3.79.1.1.1.15
Billing Configuration for the destination endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvpcFwdTmTrafficDescriptor		1.3.6.1.4.1.123.3.79.1.1.1.16
This object contains the traffic descriptor for the SPVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only)
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), tagAll(1), p0Plus1(2), p0Plus1SlashS0Plus1(3), p0Plus1SlashS0(4), p0Plus1SlashM0Plus1(5)

nncCrPvpcFwdTmPolicingOption		1.3.6.1.4.1.123.3.79.1.1.1.17
Policing Option for a PVPC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), disabled(1), tag(2), discard(3)

nncCrPvpcFwdTmBucketOneRate		1.3.6.1.4.1.123.3.79.1.1.1.18
This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvpcFwdTmBucketOneCdvt		1.3.6.1.4.1.123.3.79.1.1.1.19
This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..190000

nncCrPvpcFwdTmBucketTwoRate		1.3.6.1.4.1.123.3.79.1.1.1.20
SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvpcFwdTmBucketTwoMbs		1.3.6.1.4.1.123.3.79.1.1.1.21
This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..10000

nncCrPvpcFwdTmCdv		1.3.6.1.4.1.123.3.79.1.1.1.22
This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category.. Range: 250-10000 microseconds
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	250..10000

nncCrPvpcFwdTmClr		1.3.6.1.4.1.123.3.79.1.1.1.23
The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-#
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..7

nncCrPvpcBwdTmTrafficDescriptor		1.3.6.1.4.1.123.3.79.1.1.1.24
This object contains the traffic descriptor for the PVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only)
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), tagAll(1), p0Plus1(2), p0Plus1SlashS0Plus1(3), p0Plus1SlashS0(4), p0Plus1SlashM0Plus1(5)

nncCrPvpcBwdTmPolicingOption		1.3.6.1.4.1.123.3.79.1.1.1.25
Policing Option for a PVPC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), disabled(1), tag(2), discard(3)

nncCrPvpcBwdTmBucketOneRate		1.3.6.1.4.1.123.3.79.1.1.1.26
This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvpcBwdTmBucketOneCdvt		1.3.6.1.4.1.123.3.79.1.1.1.27
This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..190000

nncCrPvpcBwdTmBucketTwoRate		1.3.6.1.4.1.123.3.79.1.1.1.28
SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvpcBwdTmBucketTwoMbs		1.3.6.1.4.1.123.3.79.1.1.1.29
This object is to set the maximum burst size, in cells, for SIR_0p or SIR_0+1p. Used for burst traffic. Range: 1 - 10000 cells
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..10000

nncCrPvpcBwdTmCdv		1.3.6.1.4.1.123.3.79.1.1.1.30
This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	250..10000

nncCrPvpcBwdTmClr		1.3.6.1.4.1.123.3.79.1.1.1.31
The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# Range: 1 - 7
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..7

nncCrPvpcSrcAlsConfig		1.3.6.1.4.1.123.3.79.1.1.1.32
This object is used to set OAM Alarm Surveillance configuration for the source endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvpcDstAlsConfig		1.3.6.1.4.1.123.3.79.1.1.1.33
This object is used to set OAM Alarm Surveillance configuration for the destination endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvpcCreator		1.3.6.1.4.1.123.3.79.1.1.1.34
The object retrieves the creator of a PVC connection.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), nmti(1), nm5620(2), snmp(9)

nncCrPvpcRowStatus		1.3.6.1.4.1.123.3.79.1.1.1.35
This object is to control a row creation of a CR PVPC. When RowStatus is createAndWait, information for a row is cached in memory; when RowStatus is set to createAndGo or active, it indicates that all information is to be written to permanent storage, and the PVPC to be enabled. When querying the object, 'active' indicates the PVPC is physically connected and data traffic can flow. The Rowstatus of 'notInService' indicates the PVPC is physically connected but data cannot flow. If the RowStatus value of 'notReady' is returned, it indicates either the PVPC is not physically connected (ie. configured only) or the SNMP agent is awaiting further information before setting up the connection. When deleting a connection, use this object with the value 'destroy'
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

nncCrPvccTable		1.3.6.1.4.1.123.3.79.1.2
nncCrPvccTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query Cell Relay PVC connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NncCrPvccTableEntry

nncCrPvccTableEntry		1.3.6.1.4.1.123.3.79.1.2.1
An entry of nncCrPvccTable. It contains the objects required to manage CR PVCs.
Status: current	Access: not-accessible
OBJECT-TYPE
	NncCrPvccTableEntry

nncCrPvccSrcIfIndex		1.3.6.1.4.1.123.3.79.1.2.1.1
This object contains the ifIndex value for the source endpoint.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

nncCrPvccSrcVpi		1.3.6.1.4.1.123.3.79.1.2.1.2
This object contains the VPI value for the source endpoint.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

nncCrPvccSrcVci		1.3.6.1.4.1.123.3.79.1.2.1.3
This object contains the VCI value for the source endpoint.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

nncCrPvccDstIfIndex		1.3.6.1.4.1.123.3.79.1.2.1.4
This object contains the ifIndex value for the destination endpoint.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

nncCrPvccDstVpi		1.3.6.1.4.1.123.3.79.1.2.1.5
This object contains the VPI value for the destination endpoint.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

nncCrPvccDstVci		1.3.6.1.4.1.123.3.79.1.2.1.6
This object contains the VCI value for the destination endpoint.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

nncCrPvccCastType		1.3.6.1.4.1.123.3.79.1.2.1.7
This object is used to indicate whether the PVCC is point-to-point or point-to-multipoint
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	p2p(1), p2mp(2)

nncCrPvccFwdServiceCategory		1.3.6.1.4.1.123.3.79.1.2.1.8
This object is used to set the traffic service category from source endpoint to destination endpoint. This object is dependent on the value specified in nncCrPvccFwdTmTrafficDescripton object
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	cbr(1), nrtvbr(2), abr(3), ubr(4), rtvbr(6)

nncCrPvccBwdServiceCategory		1.3.6.1.4.1.123.3.79.1.2.1.9
This object is used to set the traffic service category from destination end point to source endpoint. This object is dependent on the value specified in nncCrPvccBwdTmTrafficDescripton object
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	cbr(1), nrtvbr(2), abr(3), ubr(4), rtvbr(6)

nncCrPvccFwdAbrDynTrfcIcr		1.3.6.1.4.1.123.3.79.1.2.1.10
ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvccFwdAbrDynTrfcRif		1.3.6.1.4.1.123.3.79.1.2.1.11
ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..9

nncCrPvccFwdAbrDynTrfcRdf		1.3.6.1.4.1.123.3.79.1.2.1.12
ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..9

nncCrPvccBwdAbrDynTrfcIcr		1.3.6.1.4.1.123.3.79.1.2.1.13
ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvccBwdAbrDynTrfcRif		1.3.6.1.4.1.123.3.79.1.2.1.14
ABR traffic Rate Increase Factor for the destination endpoint. Value is expressed as the -power of 2. Range: 0 - 9
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..9

nncCrPvccBwdAbrDynTrfcRdf		1.3.6.1.4.1.123.3.79.1.2.1.15
ABR traffic Rate Decrease Factor descriptor for the destination endpoint. Value is expressed as the -power of 2 Range: 0 - 9
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..9

nncCrPvccSrcBillingFlag		1.3.6.1.4.1.123.3.79.1.2.1.16
Billing Configuration for the source endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvccDstBillingFlag		1.3.6.1.4.1.123.3.79.1.2.1.17
Billing Configuration for the destination endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvccFwdTmTrafficDescriptor		1.3.6.1.4.1.123.3.79.1.2.1.18
This object contains the traffic descriptor for the PVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only)
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), tagAll(1), p0Plus1(2), p0Plus1SlashS0Plus1(3), p0Plus1SlashS0(4), p0Plus1SlashM0Plus1(5)

nncCrPvccFwdTmPolicingOption		1.3.6.1.4.1.123.3.79.1.2.1.19
Policing Option for a PVcC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), disabled(1), tag(2), discard(3)

nncCrPvccFwdTmBucketOneRate		1.3.6.1.4.1.123.3.79.1.2.1.20
This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvccFwdTmBucketOneCdvt		1.3.6.1.4.1.123.3.79.1.2.1.21
This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..190000

nncCrPvccFwdTmBucketTwoRate		1.3.6.1.4.1.123.3.79.1.2.1.22
SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvccFwdTmBucketTwoMbs		1.3.6.1.4.1.123.3.79.1.2.1.23
This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..10000

nncCrPvccFwdTmCdv		1.3.6.1.4.1.123.3.79.1.2.1.24
This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	250..10000

nncCrPvccFwdTmClr		1.3.6.1.4.1.123.3.79.1.2.1.25
The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-#
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..7

nncCrPvccFwdTmFrameDiscard		1.3.6.1.4.1.123.3.79.1.2.1.26
The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of the ATM cell header.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvccBwdTmTrafficDescriptor		1.3.6.1.4.1.123.3.79.1.2.1.27
This object contains the traffic descriptor for the SPVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only)
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), tagAll(1), p0Plus1(2), p0Plus1SlashS0Plus1(3), p0Plus1SlashS0(4), p0Plus1SlashM0Plus1(5)

nncCrPvccBwdTmPolicingOption		1.3.6.1.4.1.123.3.79.1.2.1.28
Policing Option for an PVCC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), disabled(1), tag(2), discard(3)

nncCrPvccBwdTmBucketOneRate		1.3.6.1.4.1.123.3.79.1.2.1.29
This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvccBwdTmBucketOneCdvt		1.3.6.1.4.1.123.3.79.1.2.1.30
This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..190000

nncCrPvccBwdTmBucketTwoRate		1.3.6.1.4.1.123.3.79.1.2.1.31
SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..2488320

nncCrPvccBwdTmBucketTwoMbs		1.3.6.1.4.1.123.3.79.1.2.1.32
This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..10000

nncCrPvccBwdTmCdv		1.3.6.1.4.1.123.3.79.1.2.1.33
This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	250..10000

nncCrPvccBwdTmClr		1.3.6.1.4.1.123.3.79.1.2.1.34
The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# Range: 0 - 7
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..7

nncCrPvccBwdTmFrameDiscard		1.3.6.1.4.1.123.3.79.1.2.1.35
The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of the ATM cell header.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvccSrcAlsConfig		1.3.6.1.4.1.123.3.79.1.2.1.36
This object is used to set OAM Alarm Surveillance configuration for the source endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvccDstAlsConfig		1.3.6.1.4.1.123.3.79.1.2.1.37
This object is used to set OAM Alarm Surveillance configuration for the destination endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

nncCrPvccCreator		1.3.6.1.4.1.123.3.79.1.2.1.38
The object retrieves the creator of a PVC connection.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), nmti(1), nm5620(2), snmp(9)

nncCrPvccRowStatus		1.3.6.1.4.1.123.3.79.1.2.1.39
This object is to control a row creation of a CR PVCC. When RowStatus is createAndWait, information for a row is cached in memory; when RowStatus is set to createAndGo or active, it indicates that all information is to be written to permanent storage, and the PVCC to be enabled. When querying the object, 'active' indicates the PVCC is physically connected and data traffic can flow. The Rowstatus of 'notInService' indicates the PVCC is physically connected but data cannot flow. If the RowStatus value of 'notReady' is returned, it indicates either the PVCC is not physically connected (ie. configured only) or the SNMP agent is awaiting further information before setting up the connection. When deleting a connection, use this object with the value 'destroy'
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

nncCrPvpcGroup		1.3.6.1.4.1.123.3.79.3.1
Common MIB objects for configuring a CR PVPC on Alcatel CID equipment
Status: current	Access: read-create
OBJECT-GROUP

nncCrPvccGroup		1.3.6.1.4.1.123.3.79.3.2
Common MIB objects for configuring a CR PVCC on Alcatel CID equipment
Status: current	Access: read-create
OBJECT-GROUP

nncPvcCompliance		1.3.6.1.4.1.123.3.79.4.1
The compliance statement for Alcatel CID PVC MIB implementation.
Status: current	Access: read-create
MODULE-COMPLIANCE