NETI-PM-MIB

File: NETI-PM-MIB.mib (73291 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
NETI-COMMON-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Gauge32
Counter32 Unsigned32 TEXTUAL-CONVENTION
DisplayString TruthValue DateAndTime
OBJECT-GROUP netiExperimentalGeneric

Defined Types

Counter15m  
Tok_String
TEXTUAL-CONVENTION    
  Unsigned32 0..910  

Counter24h  
Tok_String
TEXTUAL-CONVENTION    
  Unsigned32 0..86410  

PmTifEntry  
SEQUENCE    
  pmTifIndex Unsigned32
  pmTifAdminStatus INTEGER
  pmTifOperStatus INTEGER
  pmTifFailure DisplayString
  pmTifDataSource OBJECT IDENTIFIER
  pmTifDataSourceName DisplayString
  pmTifUatAlarmsEnabled TruthValue
  pmTifTresholdAlarmsEnabled TruthValue
  pmTifPeriodicEventsEnabled TruthValue
  pmTifZeroSuppressionEnabled TruthValue
  pmTifHistorySize INTEGER
  pmTif15mTresholdES Counter15m
  pmTif15mTresholdSES Counter15m
  pmTif15mTresholdBBE Gauge32
  pmTif15mTresholdSS Counter15m
  pmTif24hTresholdES Counter24h
  pmTif24hTresholdSES Counter24h
  pmTif24hTresholdBBE Gauge32
  pmTif24hTresholdSS Counter24h

PmTifCurrentEntry  
SEQUENCE    
  pmTifCurrentTime Counter15m
  pmTifCurrentSuspect TruthValue
  pmTifCurrentZS Counter32
  pmTifCurrentESs Counter15m
  pmTifCurrentSESs Counter15m
  pmTifCurrentBBEs Gauge32
  pmTifCurrentUASs Counter15m
  pmTifCurrentSSs Counter15m

PmTif15mEntry  
SEQUENCE    
  pmTif15mIndex Unsigned32
  pmTif15mTime DateAndTime
  pmTif15mSuspect TruthValue
  pmTif15mZS Counter32
  pmTif15mESs Counter15m
  pmTif15mSESs Counter15m
  pmTif15mBBEs Gauge32
  pmTif15mUASs Counter15m
  pmTif15mSSs Counter15m

PmTif24hEntry  
SEQUENCE    
  pmTif24hIndex Unsigned32
  pmTif24hTime DateAndTime
  pmTif24hSuspect TruthValue
  pmTif24hZS Counter32
  pmTif24hESs Counter24h
  pmTif24hSESs Counter24h
  pmTif24hBBEs Gauge32
  pmTif24hUASs Counter24h
  pmTif24hSSs Counter24h

PmTif24hCurrentEntry  
SEQUENCE    
  pmTif24hCurrentTime Counter15m
  pmTif24hCurrentSuspect TruthValue
  pmTif24hCurrentZS Counter32
  pmTif24hCurrentESs Counter15m
  pmTif24hCurrentSESs Counter15m
  pmTif24hCurrentBBEs Gauge32
  pmTif24hCurrentUASs Counter15m
  pmTif24hCurrentSSs Counter15m

PmAifEntry  
SEQUENCE    
  pmAifIndex Unsigned32
  pmAifAdminStatus INTEGER
  pmAifOperStatus INTEGER
  pmAifFailure DisplayString
  pmAifDataSource OBJECT IDENTIFIER
  pmAifDataSourceName DisplayString
  pmAifUatAlarmsEnabled TruthValue
  pmAifTresholdAlarmsEnabled TruthValue
  pmAifPeriodicEventsEnabled TruthValue
  pmAifZeroSuppressionEnabled TruthValue
  pmAifHistorySize INTEGER
  pmAif15mTresholdES Counter15m
  pmAif15mTresholdSES Counter15m
  pmAif15mTresholdBBE Gauge32
  pmAif24hTresholdES Counter24h
  pmAif24hTresholdSES Counter24h
  pmAif24hTresholdBBE Gauge32

PmAifCurrentEntry  
SEQUENCE    
  pmAifCurrentTime Counter15m
  pmAifCurrentSuspect TruthValue
  pmAifCurrentZS Counter32
  pmAifCurrentESs Counter15m
  pmAifCurrentSESs Counter15m
  pmAifCurrentBBEs Gauge32
  pmAifCurrentUASs Counter15m

PmAif15mEntry  
SEQUENCE    
  pmAif15mIndex Unsigned32
  pmAif15mTime DateAndTime
  pmAif15mSuspect TruthValue
  pmAif15mZS Counter32
  pmAif15mESs Counter15m
  pmAif15mSESs Counter15m
  pmAif15mBBEs Gauge32
  pmAif15mUASs Counter15m

PmAif24hEntry  
SEQUENCE    
  pmAif24hIndex Unsigned32
  pmAif24hTime DateAndTime
  pmAif24hSuspect TruthValue
  pmAif24hZS Counter32
  pmAif24hESs Counter24h
  pmAif24hSESs Counter24h
  pmAif24hBBEs Gauge32
  pmAif24hUASs Counter24h

PmAif24hCurrentEntry  
SEQUENCE    
  pmAif24hCurrentTime Counter15m
  pmAif24hCurrentSuspect TruthValue
  pmAif24hCurrentZS Counter32
  pmAif24hCurrentESs Counter15m
  pmAif24hCurrentSESs Counter15m
  pmAif24hCurrentBBEs Gauge32
  pmAif24hCurrentUASs Counter15m

PmDchEntry  
SEQUENCE    
  pmDchIndex Unsigned32
  pmDchAdminStatus INTEGER
  pmDchOperStatus INTEGER
  pmDchFailure DisplayString
  pmDchDataSource OBJECT IDENTIFIER
  pmDchDataSourceName DisplayString
  pmDchUatAlarmsEnabled TruthValue
  pmDchTresholdAlarmsEnabled TruthValue
  pmDchPeriodicEventsEnabled TruthValue
  pmDchZeroSuppressionEnabled TruthValue
  pmDchHistorySize INTEGER
  pmDch15mTresholdES Counter15m
  pmDch15mTresholdSES Counter15m
  pmDch15mTresholdBBE Gauge32
  pmDch24hTresholdES Counter24h
  pmDch24hTresholdSES Counter24h
  pmDch24hTresholdBBE Gauge32

PmDchCurrentEntry  
SEQUENCE    
  pmDchCurrentTime Counter15m
  pmDchCurrentSuspect TruthValue
  pmDchCurrentZS Counter32
  pmDchCurrentESs Counter15m
  pmDchCurrentSESs Counter15m
  pmDchCurrentBBEs Gauge32
  pmDchCurrentUASs Counter15m

PmDch15mEntry  
SEQUENCE    
  pmDch15mIndex Unsigned32
  pmDch15mTime DateAndTime
  pmDch15mSuspect TruthValue
  pmDch15mZS Counter32
  pmDch15mESs Counter15m
  pmDch15mSESs Counter15m
  pmDch15mBBEs Gauge32
  pmDch15mUASs Counter15m

PmDch24hEntry  
SEQUENCE    
  pmDch24hIndex Unsigned32
  pmDch24hTime DateAndTime
  pmDch24hSuspect TruthValue
  pmDch24hZS Counter32
  pmDch24hESs Counter24h
  pmDch24hSESs Counter24h
  pmDch24hBBEs Gauge32
  pmDch24hUASs Counter24h

PmDch24hCurrentEntry  
SEQUENCE    
  pmDch24hCurrentTime Counter15m
  pmDch24hCurrentSuspect TruthValue
  pmDch24hCurrentZS Counter32
  pmDch24hCurrentESs Counter15m
  pmDch24hCurrentSESs Counter15m
  pmDch24hCurrentBBEs Gauge32
  pmDch24hCurrentUASs Counter15m

Defined Values

netiPMMIB 1.3.6.1.4.1.2928.6.2.17
The Net Insight PM (Performance Monitoring) MIB. The MIB implements objects for monitoring the performance of trunk interfaces, access interfaces and channels according to G.826.
MODULE-IDENTITY    

netiPMMIBObjects 1.3.6.1.4.1.2928.6.2.17.1
OBJECT IDENTIFIER    

pmTifGroup 1.3.6.1.4.1.2928.6.2.17.1.1
OBJECT IDENTIFIER    

pmAifGroup 1.3.6.1.4.1.2928.6.2.17.1.2
OBJECT IDENTIFIER    

pmDchGroup 1.3.6.1.4.1.2928.6.2.17.1.3
OBJECT IDENTIFIER    

pmConformanceGroups 1.3.6.1.4.1.2928.6.2.17.1.4
OBJECT IDENTIFIER    

pmTifTable 1.3.6.1.4.1.2928.6.2.17.1.1.1
Table of Performance Monitored trunk interfaces
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmTifEntry

pmTifEntry 1.3.6.1.4.1.2928.6.2.17.1.1.1.1
One entry for each trunk interface
Status: current Access: not-accessible
OBJECT-TYPE    
  PmTifEntry  

pmTifIndex 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.1
The index uniquely identifying this trunk interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmTifAdminStatus 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.2
The desired state of the PM function. Affects the operative state of the PM object
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pmTifOperStatus 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.3
PM operative state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pmTifFailure 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.4
Shows current failure state. An empty string indicates no failure
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pmTifDataSource 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.5
The PM Data Source object
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

pmTifDataSourceName 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.6
The name of the PM Data Source
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pmTifUatAlarmsEnabled 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.7
If set to `true(1)' then UAT alarms will be sent. Unavailable time (UAT) defines a state where a service is unable to perform its normal task due to severe errors for a longer period. It begins at detection of ten consecutive SES events and ends at detection of ten consecutive non-SES events. In both cases, the 10s are considered part of unavailable respective available time and effects the visibility of G.826 PM events (they are delayed 10s) Entry and exit of UAT is declared by raising and clearing an UAT alarm (if enabled)
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmTifTresholdAlarmsEnabled 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.8
If set to `true(1)' then threshold alarms will be sent. Each 15m and 24h current register counter can be assigned a threshold value. When crossed, a threshold crossing alarm will be sent for the interval if enabled. Raised alarm will be cleared at end of a following fault free interval i.e. one with all interval counter values below their threshold values and with no UAT. Only one TC alarm per interval can be raised, regardless of how many thresholds have been crossed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmTifPeriodicEventsEnabled 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.9
If set to `true(1)' then History Periodic Events will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmTifZeroSuppressionEnabled 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.10
If set to `true(1)' then Zero Suppression mode is enabled Zero Suppression mode tells whether intervals with all current counters equal to zero shall be stored in the history log or not. If enabled, once a faulty interval is found, its current register content including a zero suppressed interval counter will be stored in the history log. The additional counter specifies how many fault free intervals have preceded the faulty one. In such way, history for a larger measurement period can be logged than would otherwise be possible
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmTifHistorySize 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.11
The size of the history log
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), small(2), large(3)  

pmTif15mTresholdES 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.12
15 minute threshold value for ES. Current ES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter15m  

pmTif15mTresholdSES 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.13
15 minute threshold value for SES. Current SES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter15m  

pmTif15mTresholdBBE 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.14
15 minute threshold value for BBE. Current BBE value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

pmTif15mTresholdSS 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.15
15 minute threshold value for SS. Current SS value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter15m  

pmTif24hTresholdES 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.16
24 hour threshold value for ES. Current ES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter24h  

pmTif24hTresholdSES 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.17
24 hour threshold value for SES. Current SES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter24h  

pmTif24hTresholdBBE 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.18
24 hour threshold value for BBE. Current BBE value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

pmTif24hTresholdSS 1.3.6.1.4.1.2928.6.2.17.1.1.1.1.19
24 hour threshold value for SS. Current SS value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter24h  

pmTifCurrentTable 1.3.6.1.4.1.2928.6.2.17.1.1.2
Table of PM data for the current 15 minute period
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmTifCurrentEntry

pmTifCurrentEntry 1.3.6.1.4.1.2928.6.2.17.1.1.2.1
One entry for each monitored object
Status: current Access: not-accessible
OBJECT-TYPE    
  PmTifCurrentEntry  

pmTifCurrentTime 1.3.6.1.4.1.2928.6.2.17.1.1.2.1.2
Elapsed time in seconds for the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTifCurrentSuspect 1.3.6.1.4.1.2928.6.2.17.1.1.2.1.3
Is Suspect flag, if set to `true(1)' the current 15 minute measurement period has unreliable measurement data.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmTifCurrentZS 1.3.6.1.4.1.2928.6.2.17.1.1.2.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmTifCurrentESs 1.3.6.1.4.1.2928.6.2.17.1.1.2.1.5
Number of Errored Seconds (ES) for the current 15 minute period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTifCurrentSESs 1.3.6.1.4.1.2928.6.2.17.1.1.2.1.6
Number of Severe Errored Seconds (SES) for the current 15 minute period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTifCurrentBBEs 1.3.6.1.4.1.2928.6.2.17.1.1.2.1.7
Number of Background Block Error (BBE) for the current 15 minute period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmTifCurrentUASs 1.3.6.1.4.1.2928.6.2.17.1.1.2.1.8
Number of Unavailable Second (UAS) for the current 15 minute period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTifCurrentSSs 1.3.6.1.4.1.2928.6.2.17.1.1.2.1.9
Number of SLIP Second (SS) for the current 15 minute period. SS is defined as one second containing one or more SLIPs
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif15mTable 1.3.6.1.4.1.2928.6.2.17.1.1.3
Table of 15 minute PM log history
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmTif15mEntry

pmTif15mEntry 1.3.6.1.4.1.2928.6.2.17.1.1.3.1
One entry for each 15 minute PM interval
Status: current Access: not-accessible
OBJECT-TYPE    
  PmTif15mEntry  

pmTif15mIndex 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.1
The index that identifies the interval for which the set of statistics is available. Index of '0' indicates the most recently completed interval, and the index is increased by one for each interval back in time.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmTif15mTime 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.2
Time stamp for this 15 minute interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

pmTif15mSuspect 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.3
Suspect flag for this 15 minute interval
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmTif15mZS 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmTif15mESs 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.5
Number of Errored Seconds (ES) for this 15 minute period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif15mSESs 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.6
Number of Severe Errored Seconds (SES) for this 15 minute period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif15mBBEs 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.7
Number of Background Block Error (BBE) for this 15 minute period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmTif15mUASs 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.8
Number of Unavailable Second (UAS) for this 15 minute period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif15mSSs 1.3.6.1.4.1.2928.6.2.17.1.1.3.1.9
Number of SLIP Second (SS) for this 15 minute period. SS is defined as one second containing one or more SLIPs
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif24hTable 1.3.6.1.4.1.2928.6.2.17.1.1.4
Table of 24 hour PM log history
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmTif24hEntry

pmTif24hEntry 1.3.6.1.4.1.2928.6.2.17.1.1.4.1
One entry for each 24 hour PM interval
Status: current Access: not-accessible
OBJECT-TYPE    
  PmTif24hEntry  

pmTif24hIndex 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.1
The index that identifies the interval for which the set of statistics is available. Index of '0' indicates the most recently completed interval, and the index is increased by one for each interval back in time.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmTif24hTime 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.2
Time stamp for this 24 hour interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

pmTif24hSuspect 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.3
Suspect flag for this 24 hour interval
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmTif24hZS 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmTif24hESs 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.5
Number of Errored Seconds (ES) for this 24 hour period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmTif24hSESs 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.6
Number of Severe Errored Seconds (SES) for this 24 hour period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmTif24hBBEs 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.7
Number of Background Block Error (BBE) for this 24 hour period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmTif24hUASs 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.8
Number of Unavailable Second (UAS) for this 24 hour period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmTif24hSSs 1.3.6.1.4.1.2928.6.2.17.1.1.4.1.9
Number of SLIP Second (SS) for this 24 hour period. SS is defined as one second containing one or more SLIPs
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmTif24hCurrentTable 1.3.6.1.4.1.2928.6.2.17.1.1.5
Table of PM data for the current 24 hour period
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmTif24hCurrentEntry

pmTif24hCurrentEntry 1.3.6.1.4.1.2928.6.2.17.1.1.5.1
One entry for each monitored object
Status: current Access: not-accessible
OBJECT-TYPE    
  PmTif24hCurrentEntry  

pmTif24hCurrentTime 1.3.6.1.4.1.2928.6.2.17.1.1.5.1.2
Elapsed time in seconds for the current 24 hour period.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif24hCurrentSuspect 1.3.6.1.4.1.2928.6.2.17.1.1.5.1.3
Is Suspect flag, if set to `true(1)' the current 24 hour measurement period has unreliable measurement data.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmTif24hCurrentZS 1.3.6.1.4.1.2928.6.2.17.1.1.5.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmTif24hCurrentESs 1.3.6.1.4.1.2928.6.2.17.1.1.5.1.5
Number of Errored Seconds (ES) for the current 24 hour period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif24hCurrentSESs 1.3.6.1.4.1.2928.6.2.17.1.1.5.1.6
Number of Severe Errored Seconds (SES) for the current 24 hour period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif24hCurrentBBEs 1.3.6.1.4.1.2928.6.2.17.1.1.5.1.7
Number of Background Block Error (BBE) for the current 24 hour period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmTif24hCurrentUASs 1.3.6.1.4.1.2928.6.2.17.1.1.5.1.8
Number of Unavailable Second (UAS) for the current 24 hour period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTif24hCurrentSSs 1.3.6.1.4.1.2928.6.2.17.1.1.5.1.9
Number of SLIP Second (SS) for the current 24 hour period. SS is defined as one second containing one or more SLIPs
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAifTable 1.3.6.1.4.1.2928.6.2.17.1.2.1
Table of Performance Monitored access interfaces
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmAifEntry

pmAifEntry 1.3.6.1.4.1.2928.6.2.17.1.2.1.1
One entry for each access interface
Status: current Access: not-accessible
OBJECT-TYPE    
  PmAifEntry  

pmAifIndex 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.1
The index uniquely identifying this access interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmAifAdminStatus 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.2
The desired state of the PM function. Affects the operative state of the PM object
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pmAifOperStatus 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.3
PM operative state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pmAifFailure 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.4
Shows current failure state. An empty string indicates no failure
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pmAifDataSource 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.5
The PM Data Source object
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

pmAifDataSourceName 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.6
The name of the PM Data Source
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pmAifUatAlarmsEnabled 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.7
If set to `true(1)' then UAT alarms will be sent. Unavailable time (UAT) defines a state where a service is unable to perform its normal task due to severe errors for a longer period. It begins at detection of ten consecutive SES events and ends at detection of ten consecutive non-SES events. In both cases, the 10s are considered part of unavailable respective available time and effects the visibility of G.826 PM events (they are delayed 10s) Entry and exit of UAT is declared by raising and clearing an UAT alarm (if enabled)
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmAifTresholdAlarmsEnabled 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.8
If set to `true(1)' then threshold alarms will be sent. Each 15m and 24h current register counter can be assigned a threshold value. When crossed, a threshold crossing alarm will be sent for the interval if enabled. Raised alarm will be cleared at end of a following fault free interval i.e. one with all interval counter values below their threshold values and with no UAT. Only one TC alarm per interval can be raised, regardless of how many thresholds have been crossed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmAifPeriodicEventsEnabled 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.9
If set to `true(1)' then History Periodic Events will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmAifZeroSuppressionEnabled 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.10
If set to `true(1)' then Zero Suppression mode is enabled Zero Suppression mode tells whether intervals with all current counters equal to zero shall be stored in the history log or not. If enabled, once a faulty interval is found, its current register content including a zero suppressed interval counter will be stored in the history log. The additional counter specifies how many fault free intervals have preceded the faulty one. In such way, history for a larger measurement period can be logged than would otherwise be possible
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmAifHistorySize 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.11
The size of the history log
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), small(2), large(3)  

pmAif15mTresholdES 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.12
15 minute threshold value for ES. Current ES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter15m  

pmAif15mTresholdSES 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.13
15 minute threshold value for SES. Current SES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter15m  

pmAif15mTresholdBBE 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.14
15 minute threshold value for BBE. Current BBE value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

pmAif24hTresholdES 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.15
24 hour threshold value for ES. Current ES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter24h  

pmAif24hTresholdSES 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.16
24 hour threshold value for SES. Current SES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter24h  

pmAif24hTresholdBBE 1.3.6.1.4.1.2928.6.2.17.1.2.1.1.17
24 hour threshold value for BBE. Current BBE value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

pmAifCurrentTable 1.3.6.1.4.1.2928.6.2.17.1.2.2
Table of PM data for the current 15 minute period
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmAifCurrentEntry

pmAifCurrentEntry 1.3.6.1.4.1.2928.6.2.17.1.2.2.1
One entry for each monitored object
Status: current Access: not-accessible
OBJECT-TYPE    
  PmAifCurrentEntry  

pmAifCurrentTime 1.3.6.1.4.1.2928.6.2.17.1.2.2.1.2
Elapsed time in seconds for the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAifCurrentSuspect 1.3.6.1.4.1.2928.6.2.17.1.2.2.1.3
Is Suspect flag, if set to `true(1)' the current 15 minute measurement period has unreliable measurement data.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmAifCurrentZS 1.3.6.1.4.1.2928.6.2.17.1.2.2.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmAifCurrentESs 1.3.6.1.4.1.2928.6.2.17.1.2.2.1.5
Number of Errored Seconds (ES) for the current 15 minute period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAifCurrentSESs 1.3.6.1.4.1.2928.6.2.17.1.2.2.1.6
Number of Severe Errored Seconds (SES) for the current 15 minute period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAifCurrentBBEs 1.3.6.1.4.1.2928.6.2.17.1.2.2.1.7
Number of Background Block Error (BBE) for the current 15 minute period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmAifCurrentUASs 1.3.6.1.4.1.2928.6.2.17.1.2.2.1.8
Number of Unavailable Second (UAS) for the current 15 minute period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAif15mTable 1.3.6.1.4.1.2928.6.2.17.1.2.3
Table of 15 minute PM interval history
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmAif15mEntry

pmAif15mEntry 1.3.6.1.4.1.2928.6.2.17.1.2.3.1
One entry for each 15 minute PM interval
Status: current Access: not-accessible
OBJECT-TYPE    
  PmAif15mEntry  

pmAif15mIndex 1.3.6.1.4.1.2928.6.2.17.1.2.3.1.1
The index that identifies the interval for which the set of statistics is available. Index of '0' indicates the most recently completed interval, and the index is increased by one for each interval back in time.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmAif15mTime 1.3.6.1.4.1.2928.6.2.17.1.2.3.1.2
Time stamp for this 15 minute interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

pmAif15mSuspect 1.3.6.1.4.1.2928.6.2.17.1.2.3.1.3
Suspect flag for this 15 minute interval
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmAif15mZS 1.3.6.1.4.1.2928.6.2.17.1.2.3.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmAif15mESs 1.3.6.1.4.1.2928.6.2.17.1.2.3.1.5
Number of Errored Seconds (ES) for this 15 minute period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAif15mSESs 1.3.6.1.4.1.2928.6.2.17.1.2.3.1.6
Number of Severe Errored Seconds (SES) for this 15 minute period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAif15mBBEs 1.3.6.1.4.1.2928.6.2.17.1.2.3.1.7
Number of Background Block Error (BBE) for this 15 minute period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmAif15mUASs 1.3.6.1.4.1.2928.6.2.17.1.2.3.1.8
Number of Unavailable Second (UAS) for this 15 minute period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAif24hTable 1.3.6.1.4.1.2928.6.2.17.1.2.4
Table of 24 hour PM log history
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmAif24hEntry

pmAif24hEntry 1.3.6.1.4.1.2928.6.2.17.1.2.4.1
One entry for each 24 hour PM interval
Status: current Access: not-accessible
OBJECT-TYPE    
  PmAif24hEntry  

pmAif24hIndex 1.3.6.1.4.1.2928.6.2.17.1.2.4.1.1
The index that identifies the interval for which the set of statistics is available. Index of '0' indicates the most recently completed interval, and the index is increased by one for each interval back in time.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmAif24hTime 1.3.6.1.4.1.2928.6.2.17.1.2.4.1.2
Time stamp for this 24 hour interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

pmAif24hSuspect 1.3.6.1.4.1.2928.6.2.17.1.2.4.1.3
Suspect flag for this 24 hour interval
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmAif24hZS 1.3.6.1.4.1.2928.6.2.17.1.2.4.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmAif24hESs 1.3.6.1.4.1.2928.6.2.17.1.2.4.1.5
Number of Errored Seconds (ES) for this 24 hour period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmAif24hSESs 1.3.6.1.4.1.2928.6.2.17.1.2.4.1.6
Number of Severe Errored Seconds (SES) for this 24 hour period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmAif24hBBEs 1.3.6.1.4.1.2928.6.2.17.1.2.4.1.7
Number of Background Block Error (BBE) for this 24 hour period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmAif24hUASs 1.3.6.1.4.1.2928.6.2.17.1.2.4.1.8
Number of Unavailable Second (UAS) for this 24 hour period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmAif24hCurrentTable 1.3.6.1.4.1.2928.6.2.17.1.2.5
Table of PM data for the current 24 hour period
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmAif24hCurrentEntry

pmAif24hCurrentEntry 1.3.6.1.4.1.2928.6.2.17.1.2.5.1
One entry for each monitored object
Status: current Access: not-accessible
OBJECT-TYPE    
  PmAif24hCurrentEntry  

pmAif24hCurrentTime 1.3.6.1.4.1.2928.6.2.17.1.2.5.1.2
Elapsed time in seconds for the current 24 hour period.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAif24hCurrentSuspect 1.3.6.1.4.1.2928.6.2.17.1.2.5.1.3
Is Suspect flag, if set to `true(1)' the current 24 hour measurement period has unreliable measurement data.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmAif24hCurrentZS 1.3.6.1.4.1.2928.6.2.17.1.2.5.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmAif24hCurrentESs 1.3.6.1.4.1.2928.6.2.17.1.2.5.1.5
Number of Errored Seconds (ES) for the current 24 hour period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAif24hCurrentSESs 1.3.6.1.4.1.2928.6.2.17.1.2.5.1.6
Number of Severe Errored Seconds (SES) for the current 24 hour period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmAif24hCurrentBBEs 1.3.6.1.4.1.2928.6.2.17.1.2.5.1.7
Number of Background Block Error (BBE) for the current 24 hour period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmAif24hCurrentUASs 1.3.6.1.4.1.2928.6.2.17.1.2.5.1.8
Number of Unavailable Second (UAS) for the current 24 hour period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDchTable 1.3.6.1.4.1.2928.6.2.17.1.3.1
Table of Performance Monitored DTM channel
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmDchEntry

pmDchEntry 1.3.6.1.4.1.2928.6.2.17.1.3.1.1
One entry for each DTM channel
Status: current Access: not-accessible
OBJECT-TYPE    
  PmDchEntry  

pmDchIndex 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.1
The index uniquely identifying this DTM channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmDchAdminStatus 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.2
The desired state of the PM function. Affects the operative state of the PM object
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pmDchOperStatus 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.3
PM operative state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pmDchFailure 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.4
Shows current failure state. An empty string indicates no failure
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pmDchDataSource 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.5
The PM Data Source object
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

pmDchDataSourceName 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.6
The name of the PM Data Source
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pmDchUatAlarmsEnabled 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.7
If set to `true(1)' then UAT alarms will be sent. Unavailable time (UAT) defines a state where a service is unable to perform its normal task due to severe errors for a longer period. It begins at detection of ten consecutive SES events and ends at detection of ten consecutive non-SES events. In both cases, the 10s are considered part of unavailable respective available time and effects the visibility of G.826 PM events (they are delayed 10s) Entry and exit of UAT is declared by raising and clearing an UAT alarm (if enabled)
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmDchTresholdAlarmsEnabled 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.8
If set to `true(1)' then threshold alarms will be sent. Each 15m and 24h current register counter can be assigned a threshold value. When crossed, a threshold crossing alarm will be sent for the interval if enabled. Raised alarm will be cleared at end of a following fault free interval i.e. one with all interval counter values below their threshold values and with no UAT. Only one TC alarm per interval can be raised, regardless of how many thresholds have been crossed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmDchPeriodicEventsEnabled 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.9
If set to `true(1)' then History Periodic Events will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmDchZeroSuppressionEnabled 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.10
If set to `true(1)' then Zero Suppression mode is enabled Zero Suppression mode tells whether intervals with all current counters equal to zero shall be stored in the history log or not. If enabled, once a faulty interval is found, its current register content including a zero suppressed interval counter will be stored in the history log. The additional counter specifies how many fault free intervals have preceded the faulty one. In such way, history for a larger measurement period can be logged than would otherwise be possible
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pmDchHistorySize 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.11
The size of the history log
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), small(2), large(3)  

pmDch15mTresholdES 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.12
15 minute threshold value for ES. Current ES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter15m  

pmDch15mTresholdSES 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.13
15 minute threshold value for SES. Current SES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter15m  

pmDch15mTresholdBBE 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.14
15 minute threshold value for BBE. Current BBE value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

pmDch24hTresholdES 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.15
24 hour threshold value for ES. Current ES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter24h  

pmDch24hTresholdSES 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.16
24 hour threshold value for SES. Current SES value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Counter24h  

pmDch24hTresholdBBE 1.3.6.1.4.1.2928.6.2.17.1.3.1.1.17
24 hour threshold value for BBE. Current BBE value equal to or above this threshold will raise a threshold alarm if enabled. A value of zero will disable threshold check.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

pmDchCurrentTable 1.3.6.1.4.1.2928.6.2.17.1.3.2
Table of PM data for the current 15 minute period
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmDchCurrentEntry

pmDchCurrentEntry 1.3.6.1.4.1.2928.6.2.17.1.3.2.1
One entry for each monitored object
Status: current Access: not-accessible
OBJECT-TYPE    
  PmDchCurrentEntry  

pmDchCurrentTime 1.3.6.1.4.1.2928.6.2.17.1.3.2.1.2
Elapsed time in seconds for the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDchCurrentSuspect 1.3.6.1.4.1.2928.6.2.17.1.3.2.1.3
Is Suspect flag, if set to `true(1)' the current 15 minute measurement period has unreliable measurement data.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmDchCurrentZS 1.3.6.1.4.1.2928.6.2.17.1.3.2.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmDchCurrentESs 1.3.6.1.4.1.2928.6.2.17.1.3.2.1.5
Number of Errored Seconds (ES) for the current 15 minute period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDchCurrentSESs 1.3.6.1.4.1.2928.6.2.17.1.3.2.1.6
Number of Severe Errored Seconds (SES) for the current 15 minute period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDchCurrentBBEs 1.3.6.1.4.1.2928.6.2.17.1.3.2.1.7
Number of Background Block Error (BBE) for the current 15 minute period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmDchCurrentUASs 1.3.6.1.4.1.2928.6.2.17.1.3.2.1.8
Number of Unavailable Second (UAS) for the current 15 minute period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDch15mTable 1.3.6.1.4.1.2928.6.2.17.1.3.3
Table of 15 minute PM interval history
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmDch15mEntry

pmDch15mEntry 1.3.6.1.4.1.2928.6.2.17.1.3.3.1
One entry for each 15 minute PM interval
Status: current Access: not-accessible
OBJECT-TYPE    
  PmDch15mEntry  

pmDch15mIndex 1.3.6.1.4.1.2928.6.2.17.1.3.3.1.1
The index that identifies the interval for which the set of statistics is available. Index of '0' indicates the most recently completed interval, and the index is increased by one for each interval back in time.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmDch15mTime 1.3.6.1.4.1.2928.6.2.17.1.3.3.1.2
Time stamp for this 15 minute interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

pmDch15mSuspect 1.3.6.1.4.1.2928.6.2.17.1.3.3.1.3
Suspect flag for this 15 minute interval
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmDch15mZS 1.3.6.1.4.1.2928.6.2.17.1.3.3.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmDch15mESs 1.3.6.1.4.1.2928.6.2.17.1.3.3.1.5
Number of Errored Seconds (ES) for this 15 minute period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDch15mSESs 1.3.6.1.4.1.2928.6.2.17.1.3.3.1.6
Number of Severe Errored Seconds (SES) for this 15 minute period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDch15mBBEs 1.3.6.1.4.1.2928.6.2.17.1.3.3.1.7
Number of Background Block Error (BBE) for this 15 minute period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmDch15mUASs 1.3.6.1.4.1.2928.6.2.17.1.3.3.1.8
Number of Unavailable Second (UAS) for this 15 minute period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDch24hTable 1.3.6.1.4.1.2928.6.2.17.1.3.4
Table of 24 hour PM interval history
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmDch24hEntry

pmDch24hEntry 1.3.6.1.4.1.2928.6.2.17.1.3.4.1
One entry for each 24 hour PM interval
Status: current Access: not-accessible
OBJECT-TYPE    
  PmDch24hEntry  

pmDch24hIndex 1.3.6.1.4.1.2928.6.2.17.1.3.4.1.1
The index that identifies the interval for which the set of statistics is available. Index of '0' indicates the most recently completed interval, and the index is increased by one for each interval back in time.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

pmDch24hTime 1.3.6.1.4.1.2928.6.2.17.1.3.4.1.2
Time stamp for this 24 hour interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

pmDch24hSuspect 1.3.6.1.4.1.2928.6.2.17.1.3.4.1.3
Suspect flag for this 24 hour interval
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmDch24hZS 1.3.6.1.4.1.2928.6.2.17.1.3.4.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmDch24hESs 1.3.6.1.4.1.2928.6.2.17.1.3.4.1.5
Number of Errored Seconds (ES) for this 24 hour period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmDch24hSESs 1.3.6.1.4.1.2928.6.2.17.1.3.4.1.6
Number of Severe Errored Seconds (SES) for this 24 hour period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmDch24hBBEs 1.3.6.1.4.1.2928.6.2.17.1.3.4.1.7
Number of Background Block Error (BBE) for this 24 hour period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmDch24hUASs 1.3.6.1.4.1.2928.6.2.17.1.3.4.1.8
Number of Unavailable Second (UAS) for this 24 hour period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter24h  

pmDch24hCurrentTable 1.3.6.1.4.1.2928.6.2.17.1.3.5
Table of PM data for the current 24 hour period
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PmDch24hCurrentEntry

pmDch24hCurrentEntry 1.3.6.1.4.1.2928.6.2.17.1.3.5.1
One entry for each monitored object
Status: current Access: not-accessible
OBJECT-TYPE    
  PmDch24hCurrentEntry  

pmDch24hCurrentTime 1.3.6.1.4.1.2928.6.2.17.1.3.5.1.2
Elapsed time in seconds for the current 24 hour period.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDch24hCurrentSuspect 1.3.6.1.4.1.2928.6.2.17.1.3.5.1.3
Is Suspect flag, if set to `true(1)' the current 24 hour measurement period has unreliable measurement data.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pmDch24hCurrentZS 1.3.6.1.4.1.2928.6.2.17.1.3.5.1.4
Zero Suppression Counter. If the performance monitoring uses zero suppression, this counter specifies how many fault free intervals have preceded the faulty one.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pmDch24hCurrentESs 1.3.6.1.4.1.2928.6.2.17.1.3.5.1.5
Number of Errored Seconds (ES) for the current 24 hour period. ES is defined as one second of available time containing one or more Errored Blocks (EB) or at least one defect
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDch24hCurrentSESs 1.3.6.1.4.1.2928.6.2.17.1.3.5.1.6
Number of Severe Errored Seconds (SES) for the current 24 hour period. SES is defined as one second of available time containing more than 30% Errored Blocks (EB) or at least one defect.
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmDch24hCurrentBBEs 1.3.6.1.4.1.2928.6.2.17.1.3.5.1.7
Number of Background Block Error (BBE) for the current 24 hour period. BBE is defined as the number of Errored Blocks (EB) during one second of available time not part of SES
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pmDch24hCurrentUASs 1.3.6.1.4.1.2928.6.2.17.1.3.5.1.8
Number of Unavailable Second (UAS) for the current 24 hour period. UAS is defined as one second of UAT (Unavailable Time). During UAT calculations of BBE, ES and SES are inhibited and no data collection of them is performed
Status: current Access: read-only
OBJECT-TYPE    
  Counter15m  

pmTifConformanceGroup 1.3.6.1.4.1.2928.6.2.17.1.4.1
The PM Trunk Interface Conformance Group.
Status: current Access: read-only
OBJECT-GROUP    

pmAifConformanceGroup 1.3.6.1.4.1.2928.6.2.17.1.4.2
The PM Access Interface Conformance Group.
Status: current Access: read-only
OBJECT-GROUP    

pmDchConformanceGroup 1.3.6.1.4.1.2928.6.2.17.1.4.3
The PM Channel Conformance Group.
Status: current Access: read-only
OBJECT-GROUP