NBS-CMMC-MIB

File: NBS-CMMC-MIB.mib (290728 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
NBS-MIB INET-ADDRESS-MIB NBS-CMMCENUM-MIB

Imported symbols

Unsigned32 Counter32 TimeTicks
IpAddress OBJECT-TYPE MODULE-IDENTITY
OBJECT-IDENTITY NOTIFICATION-TYPE DisplayString
InterfaceIndex nbs InetAddress
InetAddressType NbsCmmcEnumChassisType NbsCmmcEnumSlotOperationType
NbsCmmcEnumSlotType NbsCmmcEnumPortConnector

Defined Types

NbsCmmcSysNvramEntry  
SEQUENCE    
  nbsCmmcSysNvramIndex INTEGER
  nbsCmmcSysNvramBlock OCTET STRING

NbsCmmcSysDiscoveryHostEntry  
SEQUENCE    
  nbsCmmcSysDiscoveryHostMACAddress OCTET STRING
  nbsCmmcSysDiscoveryHostDistance INTEGER
  nbsCmmcSysDiscoveryHostIPAddress IpAddress
  nbsCmmcSysDiscoveryHostAddressType InetAddressType
  nbsCmmcSysDiscoveryHostAddress InetAddress
  nbsCmmcSysDiscoveryHostSourceIfIndex InterfaceIndex

NbsCmmcSysFirmwareEntry  
SEQUENCE    
  nbsCmmcSysFirmwareIndex INTEGER
  nbsCmmcSysFirmwareDescr DisplayString
  nbsCmmcSysFirmwareFilename DisplayString
  nbsCmmcSysFirmwareSize INTEGER
  nbsCmmcSysFirmwareMTime INTEGER
  nbsCmmcSysFirmwareVersion DisplayString
  nbsCmmcSysFirmwareDate DisplayString
  nbsCmmcSysFirmwareType INTEGER
  nbsCmmcSysFirmwareIDCs DisplayString
  nbsCmmcSysFirmwareCksum Unsigned32
  nbsCmmcSysFirmwareMd5 OCTET STRING

NbsCmmcSysProtoEntry  
SEQUENCE    
  nbsCmmcSysProtoIndex Unsigned32
  nbsCmmcSysProtoFamily DisplayString
  nbsCmmcSysProtoRate DisplayString

NbsCmmcSysTimeZoneEntry  
SEQUENCE    
  nbsCmmcSysTimeZoneIndex Unsigned32
  nbsCmmcSysTimeZoneName DisplayString

NbsCmmcSysLoaderEntry  
SEQUENCE    
  nbsCmmcSysLoaderIndex INTEGER
  nbsCmmcSysLoaderFileId INTEGER
  nbsCmmcSysLoaderProgress INTEGER
  nbsCmmcSysLoaderStatus INTEGER
  nbsCmmcSysLoaderAbort INTEGER
  nbsCmmcSysLoaderAck INTEGER
  nbsCmmcSysLoaderFilename DisplayString

NbsCmmcSysNVAreaEntry  
SEQUENCE    
  nbsCmmcSysNVAreaIfIndex InterfaceIndex
  nbsCmmcSysNVAreaBank INTEGER
  nbsCmmcSysNVAreaStatus INTEGER
  nbsCmmcSysNVAreaDescr DisplayString
  nbsCmmcSysNVAreaVersion DisplayString
  nbsCmmcSysNVAreaCksum Unsigned32

NbsCmmcSysTelnetEntry  
SEQUENCE    
  nbsCmmcSysTelnetSessionIndex INTEGER
  nbsCmmcSysTelnetSessionStat INTEGER
  nbsCmmcSysTelnetHost IpAddress
  nbsCmmcSysTelnetHostPort INTEGER
  nbsCmmcSysTelnetLocal IpAddress
  nbsCmmcSysTelnetLocalPort INTEGER
  nbsCmmcSysTelnetSessionId INTEGER
  nbsCmmcSysTelnetConnectTime DisplayString
  nbsCmmcSysTelnetHostAddressType InetAddressType
  nbsCmmcSysTelnetHostAddress InetAddress
  nbsCmmcSysTelnetLocalAddressType InetAddressType
  nbsCmmcSysTelnetLocalAddress InetAddress

NbsCmmcSysPingEntry  
SEQUENCE    
  nbsCmmcSysPingSessionIndex INTEGER
  nbsCmmcSysPingSessionStat INTEGER
  nbsCmmcSysPingAddr IpAddress
  nbsCmmcSysPingNumber Counter32
  nbsCmmcSysPingOwner INTEGER
  nbsCmmcSysPingRequests Counter32
  nbsCmmcSysPingResponses Counter32
  nbsCmmcSysPingAddressType InetAddressType
  nbsCmmcSysPingAddress InetAddress

NbsCmmcSysTrapEntry  
SEQUENCE    
  nbsCmmcSysTrapTblEntIndex INTEGER
  nbsCmmcSysTrapTblEntStatus INTEGER
  nbsCmmcSysTrapTblEntIpAddr IpAddress
  nbsCmmcSysTrapTblEntComm DisplayString
  nbsCmmcSysTrapTblEntLevel INTEGER
  nbsCmmcSysTrapTblEntPort INTEGER
  nbsCmmcSysTrapTblEntAddressType InetAddressType
  nbsCmmcSysTrapTblEntRecipient InetAddress

NbsCmmcTftpSessEntry  
SEQUENCE    
  nbsCmmcTftpSessIndex INTEGER
  nbsCmmcTftpSessStatus INTEGER
  nbsCmmcTftpSessHostIp IpAddress
  nbsCmmcTftpSessModuleId INTEGER
  nbsCmmcTftpSessAction INTEGER
  nbsCmmcTftpSessFileName DisplayString
  nbsCmmcTftpSessFileSize INTEGER
  nbsCmmcTftpSessProgress INTEGER
  nbsCmmcTftpSessAddressType InetAddressType
  nbsCmmcTftpSessAddress InetAddress

NbsCmmcChassisEntry  
SEQUENCE    
  nbsCmmcChassisIndex INTEGER
  nbsCmmcChassisType NbsCmmcEnumChassisType
  nbsCmmcChassisModel DisplayString
  nbsCmmcChassisObjectId OBJECT IDENTIFIER
  nbsCmmcChassisNumberOfSlots INTEGER
  nbsCmmcChassisHardwareRevision DisplayString
  nbsCmmcChassisPS1Status INTEGER
  nbsCmmcChassisPS2Status INTEGER
  nbsCmmcChassisPS3Status INTEGER
  nbsCmmcChassisPS4Status INTEGER
  nbsCmmcChassisFan1Status INTEGER
  nbsCmmcChassisFan2Status INTEGER
  nbsCmmcChassisFan3Status INTEGER
  nbsCmmcChassisFan4Status INTEGER
  nbsCmmcChassisTemperature INTEGER
  nbsCmmcChassisTemperatureLimit INTEGER
  nbsCmmcChassisTemperatureMin INTEGER
  nbsCmmcChassisSignalStrength INTEGER
  nbsCmmcChassisSignalStrengthMinimum INTEGER
  nbsCmmcChassisEnableAutoReset INTEGER
  nbsCmmcChassisEnableLinkTraps INTEGER
  nbsCmmcChassisEnableChassisTraps INTEGER
  nbsCmmcChassisEnableLoopbackTraps INTEGER
  nbsCmmcChassisEnableSlotChangeTraps INTEGER
  nbsCmmcChassisEnablePortTraps INTEGER
  nbsCmmcChassisResetAllModules INTEGER
  nbsCmmcChassisEnableModuleSpecificTraps INTEGER
  nbsCmmcChassisLoopbackTimeout INTEGER
  nbsCmmcChassisPortInfoBitMap OCTET STRING
  nbsCmmcChassisSlotListBitMap OCTET STRING
  nbsCmmcChassisNumberOfPortsBitMap OCTET STRING
  nbsCmmcChassisName DisplayString
  nbsCmmcChassisEnableLINTraps INTEGER
  nbsCmmcChassisEnablePortChangeTraps INTEGER
  nbsCmmcChassisEnablePortDiagsTraps INTEGER
  nbsCmmcChassisFan5Status INTEGER
  nbsCmmcChassisFan6Status INTEGER
  nbsCmmcChassisFan7Status INTEGER
  nbsCmmcChassisFan8Status INTEGER
  nbsCmmcChassisEnableSwitchoverTraps INTEGER
  nbsCmmcChassisCrossConnect INTEGER
  nbsCmmcChassisNVAreaBanks INTEGER
  nbsCmmcChassisFirmwareCaps OCTET STRING
  nbsCmmcChassisFirmwareLoad OCTET STRING
  nbsCmmcChassisNVAreaAdmin INTEGER
  nbsCmmcChassisNVAreaOper INTEGER
  nbsCmmcChassisLoader INTEGER
  nbsCmmcChassisSerialNum DisplayString
  nbsCmmcChassisFace OCTET STRING
  nbsCmmcChassisCountersState INTEGER
  nbsCmmcChassisPowerStatus INTEGER
  nbsCmmcChassisIfIndex InterfaceIndex

NbsCmmcSlotEntry  
SEQUENCE    
  nbsCmmcSlotChassisIndex INTEGER
  nbsCmmcSlotIndex INTEGER
  nbsCmmcSlotType NbsCmmcEnumSlotType
  nbsCmmcSlotModel DisplayString
  nbsCmmcSlotObjectId OBJECT IDENTIFIER
  nbsCmmcSlotNumberOfPorts INTEGER
  nbsCmmcSlotHardwareRevision DisplayString
  nbsCmmcSlotOperationType NbsCmmcEnumSlotOperationType
  nbsCmmcSlotReset INTEGER
  nbsCmmcSlotName DisplayString
  nbsCmmcSlotModuleType INTEGER
  nbsCmmcSlotModuleSlot INTEGER
  nbsCmmcSlotSwConfigurable INTEGER
  nbsCmmcSlotConfiguration OCTET STRING
  nbsCmmcSlotMacAddress OCTET STRING
  nbsCmmcSlotIPAddress IpAddress
  nbsCmmcSlotSubnetMask IpAddress
  nbsCmmcSlotBroadcastAddr IpAddress
  nbsCmmcSlotDefGateway IpAddress
  nbsCmmcSlotHoming INTEGER
  nbsCmmcSlotRedundancyAdmin INTEGER
  nbsCmmcSlotDescr DisplayString
  nbsCmmcSlotUpgradable INTEGER
  nbsCmmcSlotCrossConnect INTEGER
  nbsCmmcSlotClearType INTEGER
  nbsCmmcSlotNVAreaBanks INTEGER
  nbsCmmcSlotFirmwareCaps OCTET STRING
  nbsCmmcSlotFirmwareLoad OCTET STRING
  nbsCmmcSlotNVAreaAdmin INTEGER
  nbsCmmcSlotNVAreaOper INTEGER
  nbsCmmcSlotLoader INTEGER
  nbsCmmcSlotSerialNum DisplayString
  nbsCmmcSlotToggleRate INTEGER
  nbsCmmcSlotTemperature INTEGER
  nbsCmmcSlotCountersState INTEGER
  nbsCmmcSlotRedundancyOper INTEGER
  nbsCmmcSlotIfIndex InterfaceIndex
  nbsCmmcSlotModuleStatus INTEGER

NbsCmmcLedEntry  
SEQUENCE    
  nbsCmmcLedChassisIndex INTEGER
  nbsCmmcLedSlotIndex INTEGER
  nbsCmmcLedIndex INTEGER
  nbsCmmcLedColor INTEGER
  nbsCmmcLedDescription DisplayString

NbsCmmcSlotFaceEntry  
SEQUENCE    
  nbsCmmcSlotFaceChassisIndex INTEGER
  nbsCmmcSlotFaceSlotIndex INTEGER
  nbsCmmcSlotFaceRowIndex INTEGER
  nbsCmmcSlotFaceSummary OCTET STRING

NbsCmmcPortEntry  
SEQUENCE    
  nbsCmmcPortChassisIndex INTEGER
  nbsCmmcPortSlotIndex INTEGER
  nbsCmmcPortIndex INTEGER
  nbsCmmcPortType INTEGER
  nbsCmmcPortObjectId OBJECT IDENTIFIER
  nbsCmmcPortLink INTEGER
  nbsCmmcPortAutoNegotiation INTEGER
  nbsCmmcPortDuplex INTEGER
  nbsCmmcPortSpeed INTEGER
  nbsCmmcPortRxActivity INTEGER
  nbsCmmcPortTxActivity INTEGER
  nbsCmmcPortCollisionActivity INTEGER
  nbsCmmcPortLoopback INTEGER
  nbsCmmcPortEnableAdmin INTEGER
  nbsCmmcPortSelectLink INTEGER
  nbsCmmcPortLIN INTEGER
  nbsCmmcPortAging INTEGER
  nbsCmmcPortMaxPacketSize INTEGER
  nbsCmmcPortRemoteLoopback INTEGER
  nbsCmmcPortErrorActivity INTEGER
  nbsCmmcPortName DisplayString
  nbsCmmcPortValue OCTET STRING
  nbsCmmcPortThreshold INTEGER
  nbsCmmcPortThresholdAction INTEGER
  nbsCmmcPortRMChassis INTEGER
  nbsCmmcPortRMSlot INTEGER
  nbsCmmcPortRMPort INTEGER
  nbsCmmcPortSerialNumber DisplayString
  nbsCmmcPortVendorInfo DisplayString
  nbsCmmcPortTemperature INTEGER
  nbsCmmcPortTxPower INTEGER
  nbsCmmcPortRxPower INTEGER
  nbsCmmcPortBiasAmps INTEGER
  nbsCmmcPortSupplyVolts INTEGER
  nbsCmmcPortMedium INTEGER
  nbsCmmcPortConnector NbsCmmcEnumPortConnector
  nbsCmmcPortWavelength INTEGER
  nbsCmmcPortDigitalDiags INTEGER
  nbsCmmcPortZoneIdAdmin INTEGER
  nbsCmmcPortNominalBitRate INTEGER
  nbsCmmcPortModulePort INTEGER
  nbsCmmcPortPartRev DisplayString
  nbsCmmcPortIfIndex INTEGER
  nbsCmmcPortLinked INTEGER
  nbsCmmcPortOperational INTEGER
  nbsCmmcPortZoneChassisAdmin INTEGER
  nbsCmmcPortZoneSlotAdmin INTEGER
  nbsCmmcPortAlarmCause DisplayString
  nbsCmmcPortFlowControl INTEGER
  nbsCmmcPortAutoNegAd OCTET STRING
  nbsCmmcPortAutoNegEditable OCTET STRING
  nbsCmmcPortWavelengthX DisplayString
  nbsCmmcPortZoneIdOper INTEGER
  nbsCmmcPortZoneSlotOper INTEGER
  nbsCmmcPortZoneChassisOper INTEGER
  nbsCmmcPortLinkMatch INTEGER
  nbsCmmcPortMDIPinoutAdmin INTEGER
  nbsCmmcPortMDIPinoutOper INTEGER
  nbsCmmcPortFCRecvAdmin INTEGER
  nbsCmmcPortFCRecvOper INTEGER
  nbsCmmcPortFCSendAdmin INTEGER
  nbsCmmcPortFCSendOper INTEGER
  nbsCmmcPortAutoNegWait INTEGER
  nbsCmmcPortTemperatureLevel INTEGER
  nbsCmmcPortTxPowerLevel INTEGER
  nbsCmmcPortRxPowerLevel INTEGER
  nbsCmmcPortBiasAmpsLevel INTEGER
  nbsCmmcPortSupplyVoltsLevel INTEGER
  nbsCmmcPortAmpGainOper INTEGER
  nbsCmmcPortAmpGainAdmin INTEGER
  nbsCmmcPortAmpOutputPwrAdmin INTEGER
  nbsCmmcPortProtoCapabilities OCTET STRING
  nbsCmmcPortProtoAdmin INTEGER
  nbsCmmcPortProtoOper INTEGER
  nbsCmmcPortPreambleLen INTEGER
  nbsCmmcPortPreferred INTEGER
  nbsCmmcPortCableLen INTEGER
  nbsCmmcPortRedundantTxMode INTEGER
  nbsCmmcPortTermination INTEGER
  nbsCmmcPortDescription DisplayString
  nbsCmmcPortTransmitUnmapped INTEGER
  nbsCmmcPortToggleMode INTEGER
  nbsCmmcPortCrossConnect INTEGER
  nbsCmmcPortZoneIfIndexAdmin INTEGER
  nbsCmmcPortZoneIfIndexOper INTEGER
  nbsCmmcPortEnableOper INTEGER
  nbsCmmcPortMappingType INTEGER
  nbsCmmcPortCountersState INTEGER
  nbsCmmcPortAmpGainMinimum INTEGER
  nbsCmmcPortAmpGainMaximum INTEGER
  nbsCmmcPortAmpGainStepSize INTEGER
  nbsCmmcPortSniffer INTEGER
  nbsCmmcPortExternalLink1 InterfaceIndex
  nbsCmmcPortExternalLink2 InterfaceIndex
  nbsCmmcPortNVAreaBanks INTEGER
  nbsCmmcPortFirmwareCaps OCTET STRING
  nbsCmmcPortFirmwareLoad OCTET STRING
  nbsCmmcPortNVAreaAdmin INTEGER
  nbsCmmcPortNVAreaOper INTEGER
  nbsCmmcPortLoader INTEGER

NbsCmmcSmtpRcvrEntry  
SEQUENCE    
  nbsCmmcSmtpRcvrIndex INTEGER
  nbsCmmcSmtpRcvrEmailAddress DisplayString
  nbsCmmcSmtpRcvrStatus INTEGER

NbsCmmcSysLogMessageEntry  
SEQUENCE    
  nbsCmmcSysLogMessageType INTEGER
  nbsCmmcSysLogMessageSeverity INTEGER

NbsCmmcSysRunningLogMessageEntry  
SEQUENCE    
  nbsCmmcSysRunningLogMessageIndex INTEGER
  nbsCmmcSysRunningLogMessageSeverity DisplayString
  nbsCmmcSysRunningLogMessageErrorID INTEGER
  nbsCmmcSysRunningLogMessageSession INTEGER
  nbsCmmcSysRunningLogMessageTime INTEGER
  nbsCmmcSysRunningLogMessageModule DisplayString
  nbsCmmcSysRunningLogMessageString DisplayString

NbsCmmcSysNvramLogMessageEntry  
SEQUENCE    
  nbsCmmcSysNvramLogMessageIndex INTEGER
  nbsCmmcSysNvramLogMessageSeverity DisplayString
  nbsCmmcSysNvramLogMessageErrorID INTEGER
  nbsCmmcSysNvramLogMessageSession INTEGER
  nbsCmmcSysNvramLogMessageTime INTEGER
  nbsCmmcSysNvramLogMessageModule DisplayString
  nbsCmmcSysNvramLogMessageString DisplayString
  nbsCmmcSysNvramLogMessagePTime INTEGER
  nbsCmmcSysNvramLogMessageDateTime DisplayString

NbsCmmcSysAuditLogEntry  
SEQUENCE    
  nbsCmmcSysAuditLogIndex INTEGER
  nbsCmmcSysAuditLogUpTime INTEGER
  nbsCmmcSysAuditLogDateTime DisplayString
  nbsCmmcSysAuditLogString DisplayString

Defined Values

nbsCmmcMib 1.3.6.1.4.1.629.200
MIB for representing NBS CMMC information
MODULE-IDENTITY    

nbsCmmcObjects 1.3.6.1.4.1.629.200.1
all MIB objects in nbsCmmc MIB.
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcSystemGrp 1.3.6.1.4.1.629.200.2
Objects systemic in scope
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcIpSnmpGrp 1.3.6.1.4.1.629.200.3
IP and SNMP configuration objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcTftpGrp 1.3.6.1.4.1.629.200.4
TFTP objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcChassisGrp 1.3.6.1.4.1.629.200.6
Chassis objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcSlotGrp 1.3.6.1.4.1.629.200.7
Slot/Card/Blade objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcPortGrp 1.3.6.1.4.1.629.200.8
Port objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcNtpGrp 1.3.6.1.4.1.629.200.9
NTP objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcSmtpGrp 1.3.6.1.4.1.629.200.10
SMTP objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcSysLogGrp 1.3.6.1.4.1.629.200.11
SysLog objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcTrapGrp 1.3.6.1.4.1.629.200.12
Trap objects
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcTraps 1.3.6.1.4.1.629.200.13
SNMP Traps
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcTraps0 1.3.6.1.4.1.629.200.13.0
SNMP Traps
Status: current Access: read-write
OBJECT-IDENTITY    

nbsCmmcSysFwDescr 1.3.6.1.4.1.629.200.2.1
The description of the System Control Firmware.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysFwVers 1.3.6.1.4.1.629.200.2.2
The System Control Firmware version in the form Vmajor.minor.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

nbsCmmcSysRestart 1.3.6.1.4.1.629.200.2.3
This object is used to reset the system. Writing a coldRestart(2), causes the SNMP Agent CPU to be hardware reset, similar to a power-on cycle. Writing a warmRestart(3), causes only a restart of the System Control CPU operative software. Writing a upgrRestart(4), causes a total restart of the system software, but attempts to leave the hardware alone.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER running(1), coldRestart(2), warmRestart(3), upgrRestart(4)  

nbsCmmcSysNumRestarts 1.3.6.1.4.1.629.200.2.4
Number of warmRestarts executed by the system, since the last coldRestart or power-on cycle. A warmRestart may be initiated by: - writing a warmRestart value in nbsCmmcSysRestart - a warmRestart command from the Command Line. - the SNMP Agent Firmware due to certain conditions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nbsCmmcSysErrUptime 1.3.6.1.4.1.629.200.2.5
The time (in hundredths of a second) since the last cold reset/power cycle when a fatal error occurred. This variable shows the system uptime from the last cold reset/power on cycle, unless a fatal error oc- curred.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

nbsCmmcSysSetNvramDefaults 1.3.6.1.4.1.629.200.2.6
Writing the value setDefaults to this objects will re- store the defaults in the NVRAM data base. These values will take effect after a system reset. For the Linux-based NM family, after restoring defaults, take care not to commit running changes with the nbsCmmcSysWriteConfig object. Doing so would undo the defaults, overwriting them with the running configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER setDefaults(1)  

nbsCmmcSysSelftestLevel 1.3.6.1.4.1.629.200.2.7
NVRAM based level of the system selftest. The values are : ststNone - meaning that no selftest will be executed upon boot-up ststShort- meaning that a short selftest, of approx 10-20 seconds will be executed upon boot- up ststLong - meaning that a long/extensive self-test will be executed upon boot-up ststDiagnostics - meaning that upon boot-up the di- agnostics mode is entered. In this mode it is possible to interactively select the test or the group of tests that will be executed. This value may not be set through a SNMP SET command. This object is deprecated.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER ststNone(1), ststShort(2), ststLong(3), ststDiagnostics(4)  

nbsCmmcSysCurrentTime 1.3.6.1.4.1.629.200.2.8
The current time, expressed as the number of seconds since 00:00 (midnight) 1 January 1900 GMT. Obtained via Time Protocol (RFC 868) or set by user. Not supported value: 0
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 2208988800..4294967295  

nbsCmmcSysCurrentDateTime 1.3.6.1.4.1.629.200.2.9
The current time, derived from nbsCmmcSysCurrentTime, adjusted to Agent's local time (nbsCmmcSysTimeZone), expressed in the format 'www mm dd hh:mm:ss yyyy'. If nbsCmmcSysCurrentTime is 0, this value should be 'unknown'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..24)  

nbsCmmcSysNvramTable 1.3.6.1.4.1.629.200.2.10
Copy of Non-Volatile RAM kept in Agent, including all settings, configurations, and names for all cards managed by this Agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysNvramEntry

nbsCmmcSysNvramEntry 1.3.6.1.4.1.629.200.2.10.1
Represents a block of NVRAM
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysNvramEntry  

nbsCmmcSysNvramIndex 1.3.6.1.4.1.629.200.2.10.1.1
NVRAM Block number, starting with 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNvramBlock 1.3.6.1.4.1.629.200.2.10.1.2
Bytes contained in this block of NVRAM.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..250)  

nbsCmmcSysWriteConfig 1.3.6.1.4.1.629.200.2.11
This object is used to write the configuration file. If this returns supported, the SNMP Agent requires you to specifically write the configuration file. Any changes that are not written out will be lost on next reboot. Setting copyTempFile(4) will copy the file uploaded via nbsCmmcSysNvramTable into the non-volatile startup area.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), supported(2), write(3), copyTempFile(4)  

nbsCmmcSysUpgrade 1.3.6.1.4.1.629.200.2.12
This object allows user to initiate a transfer of firmware from the NM file system to the cards in selected slots. Before using, user should ensure the proper files have been loaded (TFTP'd) onto the NM. This object has read-write access so it will be more universally compilable, but is intended only for writing. For reading, the contents are undefined. The string should contain a comma-separated list of slots to be reprogrammed, in the format chassis.slot, or chassis.* to load all cards. While the NM is reprogramming the line card, SNMP communication may be temporarily suspended.
Status: deprecated Access: read-write
OBJECT-TYPE    
  DisplayString  

nbsCmmcSysLoginIdleTimeout 1.3.6.1.4.1.629.200.2.13
This object is used to control the idle logout timer. This timer is in minutes. If a user logged into the CLI has not typed anything for this number of minutes, the session is automatically closed. Zero means no automatic timeout.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..400000  

nbsCmmcSysDiscoveryAdmin 1.3.6.1.4.1.629.200.2.14
The Discovery protocol allows Linux NM cards to find each other on a single layer 2 network segment. By default it is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysDiscoveryOper 1.3.6.1.4.1.629.200.2.50
The current operational status of the Discovery protocol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysDiscoveryHostTable 1.3.6.1.4.1.629.200.2.15
Table that contains host information found using the L2 Discovery protocol
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysDiscoveryHostEntry

nbsCmmcSysDiscoveryHostEntry 1.3.6.1.4.1.629.200.2.15.1
Represents a single host found using the L2 Discovery protocol
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysDiscoveryHostEntry  

nbsCmmcSysDiscoveryHostMACAddress 1.3.6.1.4.1.629.200.2.15.1.1
MAC address of discovered host
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

nbsCmmcSysDiscoveryHostDistance 1.3.6.1.4.1.629.200.2.15.1.2
How many hops from me is this host?
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysDiscoveryHostIPAddress 1.3.6.1.4.1.629.200.2.15.1.3
IP address of discovered host
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysDiscoveryHostAddressType 1.3.6.1.4.1.629.200.2.15.1.4
IP address type, select IPv4 or IPv6
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nbsCmmcSysDiscoveryHostAddress 1.3.6.1.4.1.629.200.2.15.1.5
IPv4 or IPv6 IP address of discovered host, this replaces nbsCmmcSysDiscoveryHostIPAddress
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nbsCmmcSysDiscoveryHostSourceIfIndex 1.3.6.1.4.1.629.200.2.15.1.6
Interface index that the discovered host was found by. 0 for the local host.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

nbsCmmcSysLastSetFailure 1.3.6.1.4.1.629.200.2.16
If the last SNMP SET was rejected, for example with SNMP Error: BadValue (SNMP Error 3), this object should explain why the SET failed. This string may be empty (size 0) if no explanation is available. If there have been no SET requests since boot-up, this string should be empty (size 0). In addition to this object, SET errors may also be found in the nbsCmmcSysRunningLogMessageTable.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysTimeProtocol 1.3.6.1.4.1.629.200.2.17
Time Protocol (RFC 868) allows the managed device to synchronize its clock with a Time Server. When read, the agent will report notSupported(1) if this object is not supported. When set to enabled(3), it will cause the agent to contact the nbsCmmcSysTimeServer (if valid) via rdate to obtain the current time. disabled(2) is a deprecated, legacy value. Setting this value will cause a SET error.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysTimeServer 1.3.6.1.4.1.629.200.2.18
The IP Address of the Time Server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysTimeServAddressType 1.3.6.1.4.1.629.200.2.33
The Address Type of the Time Server.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nbsCmmcSysTimeServAddress 1.3.6.1.4.1.629.200.2.34
The IPv4 or IPv6 Address of the Time Server. This entry replaces nbsCmmcSysTimeServer
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nbsCmmcSysFirmwareTable 1.3.6.1.4.1.629.200.2.19
Table that lists firmware images loaded on NM.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysFirmwareEntry

nbsCmmcSysFirmwareEntry 1.3.6.1.4.1.629.200.2.19.1
Description of a firmware image
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysFirmwareEntry  

nbsCmmcSysFirmwareIndex 1.3.6.1.4.1.629.200.2.19.1.1
Unique Id for this row
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysFirmwareDescr 1.3.6.1.4.1.629.200.2.19.1.2
Description of firmware image
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysFirmwareFilename 1.3.6.1.4.1.629.200.2.19.1.3
The filename of the firmware package. If it is in the format scheme://host/path, it refers to nbsCmmcSysFirmwareURL.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysFirmwareSize 1.3.6.1.4.1.629.200.2.19.1.4
The size (in bytes) of the firmware package file
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysFirmwareMTime 1.3.6.1.4.1.629.200.2.19.1.5
The last modified time of the firmware package file itself.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysFirmwareVersion 1.3.6.1.4.1.629.200.2.19.1.6
The version of the firmware package
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysFirmwareDate 1.3.6.1.4.1.629.200.2.19.1.7
The date of release of the firmware package in RFC 2822 format
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

nbsCmmcSysFirmwareType 1.3.6.1.4.1.629.200.2.19.1.8
What kind of entity this package is for. Valid rev files have type chassis(2), slot(3), or port(4). invalid(1) indicates this entry is not a valid rev file. deleted(5) indicates this entry refers to a file that was deleted and is no longer in the management card storage area. This entry may be re-enabled if the identical file is again put on the management card. This way, indexes do not move around if files are deleted and subsequently restored. However, deleted slots may be reused by the system for new files at the system's descretion. Setting deleted(5) will delete this file permanently from the management card storage area. No values other than deleted(5) can be set.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), chassis(2), slot(3), port(4), deleted(5)  

nbsCmmcSysFirmwareIDCs 1.3.6.1.4.1.629.200.2.19.1.9
A comma separated list of module versions supported by this firmware package
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysFirmwareCksum 1.3.6.1.4.1.629.200.2.19.1.10
The checksum of the metadata. Used to uniquely identify this package file. Invalid package files have a zero Cksum. Not supported value: 0
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

nbsCmmcSysFirmwareMd5 1.3.6.1.4.1.629.200.2.19.1.11
The MD5 checksum of this firmware image. Used to verify the integrity of this package file.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(16)  

nbsCmmcSysTimeZone 1.3.6.1.4.1.629.200.2.20
User-configurable TimeZone or offset from GMT. Should be used to indicate the time local to the managed device. If the system supports nbsCmmcSysTimeZoneTableSize and it is non-zero, this object is the nbsCmmcSysTimeZoneIndex of nbsCmmcSysTimeZoneTable, which enumerates all the time zones that this system supports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), gmtMinus1200(2), gmtMinus1100(3), gmtMinus1000(4), gmtMinus0900(5), gmtMinus0800(6), gmtMinus0700(7), gmtMinus0600(8), gmtMinus0500(9), gmtMinus0400(10), gmtMinus0300(11), gmtMinus0200(12), gmtMinus0100(13), gmt(14), gmtPlus0100(15), gmtPlus0200(16), gmtPlus0300(17), gmtPlus0400(18), gmtPlus0500(19), gmtPlus0600(20), gmtPlus0700(21), gmtPlus0800(22), gmtPlus0900(23), gmtPlus1000(24), gmtPlus1100(25), gmtPlus1200(26)  

nbsCmmcSysSnmpV1 1.3.6.1.4.1.629.200.2.21
This object enables or disables SNMPv1 protocol handling.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysSnmpV2c 1.3.6.1.4.1.629.200.2.22
This object enables or disables SNMPv2c protocol handling.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysSnmpV3 1.3.6.1.4.1.629.200.2.23
This object enables or disables SNMPv3 protocol handling.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysStpAdmin 1.3.6.1.4.1.629.200.2.24
This object enables or disables STP protocol handling.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysStpOper 1.3.6.1.4.1.629.200.2.60
The current operational status of the STP protocol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysLockTypes 1.3.6.1.4.1.629.200.2.25
If enabled, forces the system only to allow writes to slots/ports that are detected as the same type as the configured type. Use nbsCmmcSlotClearType to clear the configured type. When this object is enabled(3) and a module is inserted that is incompatible with the configured type, Agent should issue the notification nbsCmmcTrapSlotModuleLocked instead of nbsCmmcTrapSlotModuleIn. The notfication nbsCmmcTrapSlotModuleIn should be issued once the lock has been cleared (see nbsCmmcSlotClearType).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysSerialTerminalType 1.3.6.1.4.1.629.200.2.26
Name of terminal to use for the serial port, e.g. vt100, xterm, ansi.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysCrossConnect 1.3.6.1.4.1.629.200.2.27
For systems which have chassis/slots supporting cross-connect functionality, this object is used to reflect the operating state and clear the entire cross-connect map, including any independent maps of subordinate chassis and slots. If there are currently no cross-connect chassis or slots in this system, the Agent must report notSupported(1). If the cross-connect mappings can not be cleared via this object, and/or can only be cleared via the Chassis, Slot, or PortCrossConnect, the Agent must also report notSupported(1). Additionally, if this object reports notSupported(1), any SNMP SET to this object should return SNMP Error 3 (bad value). If this object reports operating(2), SNMP Managers are allowed to set this object to clearing (3), which instructs the Agent to erase the cross-connect maps of all subordinate chassis and slots, so no circuits exist in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), operating(2), clearing(3)  

nbsCmmcSysCountersState 1.3.6.1.4.1.629.200.2.28
This object is used to reset all counters in this device. If agent does not have this feature, this object should be notSupported(1). In order to reset all counters to zero, set this object to clearing(3). If this feature is supported, the Agent may return the status clearing (3) during the interval in which it is resetting the counters, but otherwise should return the status counting(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), counting(2), clearing(3)  

nbsCmmcSysSerialBaudRateAdmin 1.3.6.1.4.1.629.200.2.31
The Serial Console Baud Rate when not in SLIP Mode. Setting this object will change the serial console baud rate in the BootROM configuration. It will not take effect until cold or upgrade restart. Setting this object has no effect on startup-config or the running configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER b9600(1), b19200(2), b38400(3), b115200(4)  

nbsCmmcSysSerialBaudRateOper 1.3.6.1.4.1.629.200.2.32
The current operational Serial Console Baud Rate when not in SLIP Mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER b9600(1), b19200(2), b38400(3), b115200(4)  

nbsCmmcSysProtoTableSize 1.3.6.1.4.1.629.200.2.1001
The number of entries in nbsCmmcSysProtoTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

nbsCmmcSysProtoTable 1.3.6.1.4.1.629.200.2.1002
A table to report supportable data transmission protocols.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysProtoEntry

nbsCmmcSysProtoEntry 1.3.6.1.4.1.629.200.2.1002.1
Describes a particular protocol or line rate.
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysProtoEntry  

nbsCmmcSysProtoIndex 1.3.6.1.4.1.629.200.2.1002.1.1
Protocol number.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

nbsCmmcSysProtoFamily 1.3.6.1.4.1.629.200.2.1002.1.2
Family of this protocol. The following family names must be used exactly for machine-readability: SONET T-Carrier E-Carrier Ethernet FibreChannel DigitalVideo Other family names may be added as necessary.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..16)  

nbsCmmcSysProtoRate 1.3.6.1.4.1.629.200.2.1002.1.3
Speeds or rates associated with this protocol.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..30)  

nbsCmmcSysTimeZoneTableSize 1.3.6.1.4.1.629.200.2.1003
The number of entries in nbsCmmcSysTimeZoneTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

nbsCmmcSysTimeZoneTable 1.3.6.1.4.1.629.200.2.1004
A table to report supportable timezones.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysTimeZoneEntry

nbsCmmcSysTimeZoneEntry 1.3.6.1.4.1.629.200.2.1004.1
Describes a timezone.
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysTimeZoneEntry  

nbsCmmcSysTimeZoneIndex 1.3.6.1.4.1.629.200.2.1004.1.1
TimeZone index corresponding to a nbsCmmcSysTimeZone setting. The first entry is reserved for 'notSupported'. The next 25 entries are reserved for GMT-12 (gmtMinus1200) through GMT+12 (gmtPlus1200) for compatibility with the older nbsCmmcSysTimeZone enumeration. Entries 27 and up are specific to the system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

nbsCmmcSysTimeZoneName 1.3.6.1.4.1.629.200.2.1004.1.2
Name of this timezone.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..30)  

nbsCmmcSysLoaderTableSize 1.3.6.1.4.1.629.200.2.1010
The maximum number of concurrent loader sessions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysLoaderTable 1.3.6.1.4.1.629.200.2.1011
A table to manage multiple loader (transfer from NM to blade or line card) sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysLoaderEntry

nbsCmmcSysLoaderEntry 1.3.6.1.4.1.629.200.2.1011.1
Describes a particular loader session.
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysLoaderEntry  

nbsCmmcSysLoaderIndex 1.3.6.1.4.1.629.200.2.1011.1.1
Agent-determined session number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysLoaderFileId 1.3.6.1.4.1.629.200.2.1011.1.2
The nbsCmmcSysFirmwareIndex value corresponding to the file being loaded.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysLoaderProgress 1.3.6.1.4.1.629.200.2.1011.1.3
Percentage of file transferred so far.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysLoaderStatus 1.3.6.1.4.1.629.200.2.1011.1.4
Status of this file transfer. The value idle (1) indicates this loader session is unused. The value transferring (2) indicates this transfer is underway. The value completed (3) indicates this transfer finished successfully. The value aborted (4) indicates the transfer was stopped before completion.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER idle(1), transferring(2), completed(3), aborted(4)  

nbsCmmcSysLoaderAbort 1.3.6.1.4.1.629.200.2.1011.1.5
This object allows users to prematurely halt this loader session. If this loader session can not be aborted, the agent will report notSupported(1). If nbsCmmcSysLoaderStatus is transferring(2) and this feature is supported, the agent will report supported(2). When a GET on this object returns supported(2), a user may set this object to abort(3). Doing so will cause the agent to stop the transfer and change nbsCmmcSysLoaderStatus to aborted(4). The agent should report the values of nbsCmmcSysLoaderFileId and nbsCmmcSysLoaderProgress as the state they were in at the time of the abort. Please note that aborting a loader session will leave the destination memory bank with a corrupted, unusable firmware image. It is important for users to correct this promptly, by (re)transferring a good and complete firmware image.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), supported(2), abort(3)  

nbsCmmcSysLoaderAck 1.3.6.1.4.1.629.200.2.1011.1.6
This object allows users to ACKnowledge the termination of this loader session. If nbsCmmcSysLoaderStatus is idle(1) or transferring(2), the agent will report this object as notSupported(1). If nbsCmmcSysLoaderStatus is completed(3) or aborted(4), the agent should report supported(2). When a GET on this object returns supported(2), a user may set this object to acknowledge(3). Doing so will cause the agent to either: - delete this entire row of the nbsCmmcSysLoaderTable, or - reset this row to its idle state by clearing both nbsCmmcSysLoaderFileId and nbsCmmcSysLoaderProgress to zero, and changing nbsCmmcSysLoaderStatus to idle(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), supported(2), acknowledge(3)  

nbsCmmcSysLoaderFilename 1.3.6.1.4.1.629.200.2.1011.1.7
A copy of nbsCmmcSysFirmwareFilename, for display.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

nbsCmmcSysFirmwareURL 1.3.6.1.4.1.629.200.2.1020
Remote URL in the form: scheme://[username[:password]@]IP[:port][/path/]filename to use for the remote entry in FirmwareTable. When set, the remote URL will be retrieved and checked for compatability. If it is a valid firmware file, a row in FirmwareTable will be instantiated to represent this file. The corresponding FirmwareFilename will be set to the URL, and FirmwareType set accordingly. The file may or not be cached locally if this row is chosen for a Chassis or SlotFirmwareLoad. If the user has changed the remote file after FirmwareURL is set, but before a Chassis or SlotFirmwareLoad is initiated, the results are undefined. If the remote file has changed, setting this object again will 'refresh' its FirmwareTable entry. If a zero length string is set, the corresponding FirmwareType in the FirmwareTable row will be changed to 'deleted', and any local cache of the file deleted. If an invalid URL is set, or the remote file is invalid or does not exist, the corresponding FirmwareTable row will be changed to 'deleted'. If port is omitted, an appropriate port according to the scheme will be automatically selected Note that only numeric IPs are supported; there is no resolver. If a remote file fetch is in progress, or any Chassis or SlotFirmwareLoad involving a remote URL is in progress, sets to this object will be rejected. This object is not stored in the running configuration. It is an 'impulse' object.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysFirmwareURLStatus 1.3.6.1.4.1.629.200.2.1021
The state of the URL fetch process initiated by a write to SysFirmwareURL. Setting the Chassis or SlotFirmwareLoad object to the URL index will be rejected unless this object returns completed(4).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), idle(2), transferring(3), completed(4), failed(5)  

nbsCmmcSysNVAreaTableSize 1.3.6.1.4.1.629.200.2.3000
The number of non-volatile firmware flash image areas system wide
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNVAreaTable 1.3.6.1.4.1.629.200.2.3001
Table that lists firmware images loaded on a chassis, slot, or port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysNVAreaEntry

nbsCmmcSysNVAreaEntry 1.3.6.1.4.1.629.200.2.3001.1
Description of a firmware image
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysNVAreaEntry  

nbsCmmcSysNVAreaIfIndex 1.3.6.1.4.1.629.200.2.3001.1.1
Interface index in the form CCSSPPP
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex 100000..9999999  

nbsCmmcSysNVAreaBank 1.3.6.1.4.1.629.200.2.3001.1.2
Number of this memory bank / storage area. Numbering must start from one, and bank numbers must be contiguous.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNVAreaStatus 1.3.6.1.4.1.629.200.2.3001.1.3
invalid(1) indicates this entry is not a valid NV area. primary(2) indicates this entry is the primary NV area. The next time the hardware is reset, this image will be loaded. This setting may be changed via nbsCmmcChassisNVAreaAdmin or nbsCmmcSlotNVAreaAdmin. backup(3) indicates this entry is the backup NV area. The next time the hardware is reset, this image will be loaded if the primary image fails to load. This image is subject to being overwritten if a new image is downloaded and there are no other banks available. erased(4) indicates this entry refers to an area that was erased and is no longer in the NV storage area. busy(5) indicates this NV area is busy.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), primary(2), backup(3), erased(4), busy(5)  

nbsCmmcSysNVAreaDescr 1.3.6.1.4.1.629.200.2.3001.1.4
Description of firmware image
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysNVAreaVersion 1.3.6.1.4.1.629.200.2.3001.1.5
The version of the firmware package
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysNVAreaCksum 1.3.6.1.4.1.629.200.2.3001.1.6
The checksum of the metadata. Used to uniquely identify this NV area. Invalid NV areas have a zero Cksum. Not supported value: 0
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

nbsCmmcIpCfg 1.3.6.1.4.1.629.200.3.1
OBJECT IDENTIFIER    

nbsCmmcSnmpCfg 1.3.6.1.4.1.629.200.3.2
OBJECT IDENTIFIER    

nbsCmmcPrvIpAddr 1.3.6.1.4.1.629.200.3.1.1
The SNMP Agent Administrative value of the IP Address for the private in-band access. This value is stored in the system NVRAM. The current operational IP Address may be obtained by accessing the ipAdEntAddr entry in the ipAddrTable, for ipAdEntIfIndex equal to the private interface value. If the system has no current operational IP Address, meaning that, the access is done out-of-band, then this value takes effect immediately. In this case the NetMask and the BcastAddr will be automatically built. Otherwise it will take effect after a system reset.
Status: deprecated Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcPrvNetMask 1.3.6.1.4.1.629.200.3.1.2
The SNMP Agent Administrative value of the subnet mask for the private in-band access. This value is stored in the system NVRAM. The current operational IP Adress may be obtained by accessing the ipAdEntNetMask entry in the ipAddrTable, for ipAdEntIfIndex equal to the private interface value. If the system has no current operational IP Address, meaning that the access is done out-of-band, then this value takes effect immediately. Otherwise it will take effect after a system reset
Status: deprecated Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcPrvBcastAddr 1.3.6.1.4.1.629.200.3.1.3
The SNMP Agent Administrative value of the IP Broad- cast Address for the private in-band access. This value is stored in the system NVRAM. The current operational IP Adress may be obtained via the ipAdEntBcastAddr entry in the ipAddrTable for ipAdEntIfIndex equal to the private interface value. If the system has no current operational IP Address, meaning that the access is done out-of-band, then this value takes effect immediately. Otherwise it will take effect after a system reset
Status: deprecated Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysIpAddr 1.3.6.1.4.1.629.200.3.1.4
The SNMP Agent Administrative value of the IP Address for the system. This value is stored in the system NVRAM. The current operational IP Adress may be obtained by accessing the ipAdEntAddr entry in the ipAddrTable for ipAdEntIfIndex equal to the system interface value. If the system has no current operational IP Address, meaning that the access is done out-of-band, then this value takes effect immediately. In this case the NetMask and the BcastAddr will be automatically built. Otherwise it will take effect after a system reset.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysNetMask 1.3.6.1.4.1.629.200.3.1.5
The SNMP Agent Administrative value of the subnet mask for the system. This value is stored in the system NVRAM. The current operational IP Adress may be obtained by accessing the ipAdEntNetMask entry in the ipAddrTable for ipAdEntIfIndex equal to the system interface value If the system has no current operational IP Address, meaning that the access is done out-of-band, then this value takes effect immediately. Otherwise it will take effect after a system reset
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysBcastAddr 1.3.6.1.4.1.629.200.3.1.6
The SNMP Agent Administrative value of the IP Broadcast Address for the system. This value is stored in the system NVRAM. The current operational IP Adress may be obtained by accessing the ipAdEntBcastAddr entry in the ipAddrTable for ipAdEntIfIndex equal to the system interface value. If the system has no current operational IP Address, meaning that the access is done out-of-band, then this value takes effect immediately. Otherwise it will take effect after a system reset
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysObIpAddr 1.3.6.1.4.1.629.200.3.1.7
The SNMP Agent Administrative value of the IP Address for the out-band access. This value is stored in the system NVRAM. The current operational IP Adress may be obtained by accessing the ipAdEntAddr entry in the ipAddrTable, for ipAdEntIfIndex equal to the SLIP interface value. If the system has no current operational Out-Band IP Address, meaning that, the access is done in-band, then this value takes effect immediately. In this case the NetMask and the BcastAddr will be automa- tically built. Otherwise it will take effect after a system reset
Status: deprecated Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysObNetMask 1.3.6.1.4.1.629.200.3.1.8
The SNMP Agent Administrative value of the subnet mask for the out-band access. This value is stored in the system NVRAM. The current operational IP Adress may be obtained by accessing the ipAdEntNetMask entry in the ipAddrTable, for ipAdEntIfIndex equal to the SLIP interface value. If the system has no current operational Out-Band IP Address, meaning that, the access is done in-band, then this value takes effect immediately. Otherwise it will take effect after a system reset
Status: deprecated Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysObBcastAddr 1.3.6.1.4.1.629.200.3.1.9
The SNMP Agent Administrative value of the IP Broadcast Address for the in-band access. This value is stored in the system NVRAM. The current operational IP Adress may be obtained by accessing the ipAdEntBcastAddr entry in the ipAddrTable, for ipAdEntIfIndex equal to the SLIP interface value. If the system has no current operational Out-Band IP Address, meaning that, the access is done in-band, then this value takes effect immediately. Otherwise it will take effect after a system reset
Status: deprecated Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysDefaultGateway 1.3.6.1.4.1.629.200.3.1.10
The SNMP Agent Administrative value of the Default Gateway. This value is stored in the system NVRAM. The current operational Default Gateway IP Adress may be obtained by accessing ipRouteNextHop object of the 0.0.0.0 entry in the ipRouteTable. If the system has no current operational Default Gateway IP Address, then this value takes effect immediately. Otherwise it will take effect after a system reset.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysAdminBootpState 1.3.6.1.4.1.629.200.3.1.11
This object indicates whether the NM should automatically retrieve its IP settings from its local network using BootP or DHCP. This setting will be stored in persistent memory, and thus preserved over system resets and power cycles.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nbsCmmcSysRunBootpState 1.3.6.1.4.1.629.200.3.1.12
This object indicates whether BootP or DHCP was enabled when the NM last booted.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nbsCmmcSysSerialLineMode 1.3.6.1.4.1.629.200.3.1.13
The mode in which the serial line is used: by the local Administrative Interface, or as a SLIP line. Note that setting this object to adminIf(1) value while in SLIP mode will abort the serial connection between the SNMP Manager and the device. Setting this object to slipIf(2) while in Administrative Interface Mode will abort the local terminal connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER adminIf(1), slipIf(2)  

nbsCmmcSysSerialSlipBaudRate 1.3.6.1.4.1.629.200.3.1.14
The Serial Line Baud Rate when in SLIP Mode. This value is stored in the system NVRAM as well as in the SNMP Agent current configuration.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER b9600(1), b19200(2), b38400(3)  

nbsCmmcSysArpAgingTime 1.3.6.1.4.1.629.200.3.1.15
The aging time for the ARP table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000000  

nbsCmmcSysMaxTelnetSessions 1.3.6.1.4.1.629.200.3.1.16
The maximum number of entries in nbsCmmcSysTelnetTable.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysTelnetTable 1.3.6.1.4.1.629.200.3.1.17
A table describing the Telnet Sessions
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysTelnetEntry

nbsCmmcSysTelnetEntry 1.3.6.1.4.1.629.200.3.1.17.1
Contains the information describing a Telnet Session
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysTelnetEntry  

nbsCmmcSysTelnetSessionIndex 1.3.6.1.4.1.629.200.3.1.17.1.1
The index in the Telnet Table for this entry.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysTelnetSessionStat 1.3.6.1.4.1.629.200.3.1.17.1.2
This object indicates if there is any TELNET session in progress.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), disconnect(2)  

nbsCmmcSysTelnetHost 1.3.6.1.4.1.629.200.3.1.17.1.3
This object indicates the remote IP host that connected to the local device. It is 0.0.0.0 if there is no active Telnet session
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysTelnetHostPort 1.3.6.1.4.1.629.200.3.1.17.1.4
This object indicates the port number of the remote IP host.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysTelnetLocal 1.3.6.1.4.1.629.200.3.1.17.1.5
This object indicates the IP address of the local device. It is 0.0.0.0 if there is no active Telnet session
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysTelnetLocalPort 1.3.6.1.4.1.629.200.3.1.17.1.6
This object indicates the local port number.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysTelnetSessionId 1.3.6.1.4.1.629.200.3.1.17.1.7
The internal session identifier for this entry.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysTelnetConnectTime 1.3.6.1.4.1.629.200.3.1.17.1.8
This object indicates the length of time connected.
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysTelnetHostAddressType 1.3.6.1.4.1.629.200.3.1.17.1.9
This object indicates the remote host address type.
Status: deprecated Access: read-only
OBJECT-TYPE    
  InetAddressType  

nbsCmmcSysTelnetHostAddress 1.3.6.1.4.1.629.200.3.1.17.1.10
This object indicates the remote host address, IPv4 or IPv6. This field supercedes nbsCmmcSysTelnetHost
Status: deprecated Access: read-only
OBJECT-TYPE    
  InetAddress  

nbsCmmcSysTelnetLocalAddressType 1.3.6.1.4.1.629.200.3.1.17.1.11
This object indicates the local host address type.
Status: deprecated Access: read-only
OBJECT-TYPE    
  InetAddressType  

nbsCmmcSysTelnetLocalAddress 1.3.6.1.4.1.629.200.3.1.17.1.12
This object indicates the local host address, IPv4 or IPv6. This field supercedes nbsCmmcSysTelnetLocal
Status: deprecated Access: read-only
OBJECT-TYPE    
  InetAddress  

nbsCmmcSysMaxPingSessions 1.3.6.1.4.1.629.200.3.1.18
The maximum number of Ping Sessions allowed in this system.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysPingTable 1.3.6.1.4.1.629.200.3.1.19
A table describing the Ping Sessions
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysPingEntry

nbsCmmcSysPingEntry 1.3.6.1.4.1.629.200.3.1.19.1
Contains the information describing a Ping Session
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysPingEntry  

nbsCmmcSysPingSessionIndex 1.3.6.1.4.1.629.200.3.1.19.1.1
Index in the Ping Session Table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysPingSessionStat 1.3.6.1.4.1.629.200.3.1.19.1.2
This object controls the activity of the PING process progress. If GET idlePing(1) shows that the ping process is idle If SET idlePing(1) stops an active ping process, if any. If GET runPing(2) shows an active ping process. If SET runPing(2) starts an active ping process, if none active. This has to be the last SET in order to activate the PING process
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER idlePing(1), runPing(2)  

nbsCmmcSysPingAddr 1.3.6.1.4.1.629.200.3.1.19.1.3
The IP Address to which the NM device will ping. Setting this variable initiates the ping sequence. The default value is the loopback address 127.0.0.1.
Status: deprecated Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysPingNumber 1.3.6.1.4.1.629.200.3.1.19.1.4
The number of ICMP echo packets (pings) to be sent. The default value is 1.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Counter32  

nbsCmmcSysPingOwner 1.3.6.1.4.1.629.200.3.1.19.1.5
If a Ping Process is active, then the value of this object shows who activated it: the Administrative Interface, the SNMP Agent or a Web Based Manager.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER none(1), adminInterface(2), snmpAgent(3), webManager(4)  

nbsCmmcSysPingRequests 1.3.6.1.4.1.629.200.3.1.19.1.6
The number of ICMP echo request (pings) sent.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

nbsCmmcSysPingResponses 1.3.6.1.4.1.629.200.3.1.19.1.7
The number of ICMP echo response packets received.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

nbsCmmcSysPingAddressType 1.3.6.1.4.1.629.200.3.1.19.1.8
The IP Address to which the NM device will ping. Setting this variable initiates the ping sequence. The default value is the loopback address 127.0.0.1.
Status: deprecated Access: read-write
OBJECT-TYPE    
  InetAddressType  

nbsCmmcSysPingAddress 1.3.6.1.4.1.629.200.3.1.19.1.9
The IP Address to which the NM device will ping. Setting this variable initiates the ping sequence. The default value is the loopback address 127.0.0.1. Supercedes the field nbsCmmcSysPingAddr
Status: deprecated Access: read-write
OBJECT-TYPE    
  InetAddress  

nbsCmmcSysTelnetServer 1.3.6.1.4.1.629.200.3.1.20
The telnet server ships disabled by default on the NM2. Not supported means that the telnet server status cannot be changed from SNMP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysSshServer 1.3.6.1.4.1.629.200.3.1.21
The ssh server ships enabled by default on the NM2. Not supported means that the ssh server status cannot be changed from SNMP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysIpAddrOper 1.3.6.1.4.1.629.200.3.1.22
The IP address actually being used by the Agent. The Agent's IP address may be assigned automatically by a bootp or DHCP server, or a static IP may be assigned via the nbsCmmcSysIpAddr object.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysNetMaskOper 1.3.6.1.4.1.629.200.3.1.23
The subnet mask actually being used by the Agent. The Agent's subnet mask may be assigned automatically by a bootp or DHCP server, or may be assigned via the nbsCmmcSysNetMask object.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysBcastAddrOper 1.3.6.1.4.1.629.200.3.1.24
The IP Broadcast address actually being used by the Agent. The Agent's IP Broadcast address may be assigned automatically by a bootp or DHCP server, or may be assigned via the nbsCmmcSysBcastAddr object.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysDefaultGatewayOper 1.3.6.1.4.1.629.200.3.1.25
The Default Gateway actually being used by the Agent. The Agent's Default Gateway may be assigned automatically by a bootp or DHCP server, or may be assigned via the nbsCmmcSysBcastAddr object.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysWebServer 1.3.6.1.4.1.629.200.3.1.26
The web server ships enabled by default on the NM2. Not supported means that the web server status cannot be changed from SNMP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysWebPort 1.3.6.1.4.1.629.200.3.1.27
The TCP/UDP/IP port the Agent will listen on for web (HTTP) traffic when nbsCmmcSysWebServer is enabled(3). Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

nbsCmmcSysTelnetPort 1.3.6.1.4.1.629.200.3.1.28
The TCP/IP port the Agent will listen on for Telnet traffic when nbsCmmcSysTelnetServer is enabled(3). Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

nbsCmmcSysSshPort 1.3.6.1.4.1.629.200.3.1.29
The TCP/UDP/IP port the Agent will listen on for Secure Shell (SSH) traffic if nbsCmmcSysSshServer is enabled(3). Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

nbsCmmcSysScpServer 1.3.6.1.4.1.629.200.3.1.30
The Secure Copy Protocol (SCP) server ships disabled by default on the NM2. This feature shares nbsCmmcSysSshPort with SSH, and will not work unless nbsCmmcSysSshServer is enabled(3). Not supported means that the scp server status cannot be changed from SNMP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysNetconfServer 1.3.6.1.4.1.629.200.3.1.31
The Netconf server ships disabled by default. Not supported means that the Netconf server status cannot be changed from SNMP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSysNetconfPort 1.3.6.1.4.1.629.200.3.1.32
The TCP/UDP/IP port the Agent will listen on for Netconf traffic if nbsCmmcSysNetconfServer is enabled(3). Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

nbsCmmcSysWriteCommunity 1.3.6.1.4.1.629.200.3.2.1
The SNMP Agent Administrative value of the write community string. This value is stored in the system NVRAM. It will take effect after a system reset. The object may not be read for obvious security reasons. A GET request will be answered by a zero length string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysReadCommunity 1.3.6.1.4.1.629.200.3.2.2
The SNMP Agent Administrative value of the read community string. This value is stored in the system NVRAM. It will take effect after a system reset
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysTrapTblMaxSize 1.3.6.1.4.1.629.200.3.2.3
The maximum size (number of rows) allowed in the trap table
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysTrapTable 1.3.6.1.4.1.629.200.3.2.4
A table of managers to whom will the traps generated by the SNMP agent will be sent. It represents the current operational table as well as the NVRAM saved table. The entries in the table are saved over system resets and power up cycles
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysTrapEntry

nbsCmmcSysTrapEntry 1.3.6.1.4.1.629.200.3.2.4.1
Contains the information necessary to generate a trap to be sent to a particular manager. The object nbsCmmcSysTrapTblEntStatus, when written is used to create or delete an entry/row in nbsCmmcSysTrapTable. To create a new entry a SET PDU with the nbsCmmcSysTrapTblEntRecipient, nbsCmmcSysTrapTblEntComm and nbsCmmcSysTrapTblEntStatus objects is required.
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysTrapEntry  

nbsCmmcSysTrapTblEntIndex 1.3.6.1.4.1.629.200.3.2.4.1.1
The index of the entry/row in the trap table in the range 1 to the value of nbsCmmcSysTrapTblMaxSize.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysTrapTblEntStatus 1.3.6.1.4.1.629.200.3.2.4.1.2
This object is used to get/set the validity of the information contained by nbsCmmcSysTrapEntry row. Setting this object to the value invalid(1) has the effect of deleting the corresponding nbsCmmcSysTrapTable entry. Deleting and entry has the effect of initializing it to default values : IpAddr = 0.0.0.0 & Comm = null string. Setting this object to the value valid(2) entry has the effect of creating a new row in the nbsCmmcSysTrapTable object, if an entry with the same nbsCmmcSysTrapTblEntIpAddr does not exist. If such an entry exists, then a 'badValue' error will be returned. The GET operations will receive a value of valid(2) for existing entries. An invalid(1) value indicates an entry that was deleted by a previous SET operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), active(2)  

nbsCmmcSysTrapTblEntIpAddr 1.3.6.1.4.1.629.200.3.2.4.1.3
IPv4 Address of a manager that is to receive the SNMP agent traps. This field is now read-only and is superseded CmmcSysTrapTblEntRecipient
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysTrapTblEntComm 1.3.6.1.4.1.629.200.3.2.4.1.4
Community string used by the SNMP agent in the traps generated to this SNMP manager/receiver.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysTrapTblEntLevel 1.3.6.1.4.1.629.200.3.2.4.1.5
Event severity level threshold for this SNMP manager. If the event severity level is at least nbsCmmcSysTrapTblEntLevel, the SNMP agent will generate a trap to this SNMP manager/receiver.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), fatal(2), error(3), warning(4), deprecated5(5), deprecated6(6), alarm(7)  

nbsCmmcSysTrapTblEntPort 1.3.6.1.4.1.629.200.3.2.4.1.6
The UDP/IP port on the Manager to which the Agent will send SNMP traps/notifications. Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

nbsCmmcSysTrapTblEntAddressType 1.3.6.1.4.1.629.200.3.2.4.1.7
The address type of nbsCmmcSysTrapTblEntRecipient. Currently ipv4 and ipv6 are supported.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nbsCmmcSysTrapTblEntRecipient 1.3.6.1.4.1.629.200.3.2.4.1.8
IP Address (IPv4 or IPv6) or hostname of a manager that is to receive the SNMP agent generated traps; supersedes nbsCmmcSysTrapTblEntIpAddr
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nbsCmmcSysEnablePowerSupplyTraps 1.3.6.1.4.1.629.200.3.2.11
Indicates whether powerSupplyAllarmOn and powerSupplyAllarmOff traps in this MIB should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nbsCmmcSysEnableModuleTraps 1.3.6.1.4.1.629.200.3.2.12
Indicates whether moduleUp and moduleDown traps in this MIB should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nbsCmmcSysEnableBridgeTraps 1.3.6.1.4.1.629.200.3.2.13
Indicates whether newRoot and topologyChange traps in the BRIDGE-MIB should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nbsCmmcSysEnableIpAccessTraps 1.3.6.1.4.1.629.200.3.2.14
Indicates whether IP access traps in this MIB should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nbsCmmcSysSnmpPortAdmin 1.3.6.1.4.1.629.200.3.2.15
The UDP/IP port the Agent will listen on for SNMP traffic after the next system restart. Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

nbsCmmcSysSnmpPortOper 1.3.6.1.4.1.629.200.3.2.16
The UDP/IP port the Agent is listening on for SNMP traffic now. Not supported value: -1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

nbsCmmcSysTftpHostIP 1.3.6.1.4.1.629.200.4.1
This is the IP Address of the TFTP Server/Client serving the actual TFTP transfer. A TFTP transfer may mean a software/microcode/parameter/etc.. download/upload process, initiated by the SNMP agent, for one of the modules, including, but not only, the System Control Card. It is 0.0.0.0, if th TFTP host is undefined.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcTftpMaxSessionNum 1.3.6.1.4.1.629.200.4.2
Maximum number of parallel TFTP sessions that are supported by the system
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcTftpSessTable 1.3.6.1.4.1.629.200.4.3
A table that describes the active TFTP sessions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcTftpSessEntry

nbsCmmcTftpSessEntry 1.3.6.1.4.1.629.200.4.3.1
Contains a description of a particular TFTP session
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcTftpSessEntry  

nbsCmmcTftpSessIndex 1.3.6.1.4.1.629.200.4.3.1.1
The index of the TFTP session (1..nbsCmmcTftpMaxSessionNum)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcTftpSessStatus 1.3.6.1.4.1.629.200.4.3.1.2
The status of this TFTP session
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), create(2), underCreation(3), active(4), transferEnded(5), failed(6)  

nbsCmmcTftpSessHostIp 1.3.6.1.4.1.629.200.4.3.1.3
This is the IP Address of the TFTP Host (Server/Client) serving the TFTP session as a source/destination. An IP address of 0.0.0.0 signifies that no setup has been done. Setting the nbsCmmcTftpSessHostIp value will change also the the default of all the instances of nbsCmmcTftpSessHostIp that were not specifically initialized by a SET operation.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcTftpSessModuleId 1.3.6.1.4.1.629.200.4.3.1.4
Deprecated. Module Id that owns this TFTP session (whose firmware/microcode/parameters/etc. are transferred
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcTftpSessAction 1.3.6.1.4.1.629.200.4.3.1.5
This object is used to initiate a TFTP file transfer. If nbsCmmcTftpSessStatus is not active (4), the Agent should report the value inactive (1). The Manager may initiate a session between the Agent and the host specified in nbsCmmcTftpSessHostIp by changing the value of this object. Setting the value downloadNM (2) tells the Agent to transfer its firmware image from the host to itself. Setting the value uploadNM (3) tells the Agent to transfer its firmware image from itself to the host. Setting the value downloadPar (4) tells the Agent to transfer a previous backup of its configuration from the host to itself. Setting the value uploadPar (5) tells the Agent to send a backup file of its current configuration to the host. For any other type of file, the Manager should set this value to downloadFile (6) to send a file from the host to the NM, and uploadFile (7) to transfer a file from the NM to the host.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), downloadNM(2), uploadNM(3), downloadPar(4), uploadPar(5), downloadFile(6), uploadFile(7)  

nbsCmmcTftpSessFileName 1.3.6.1.4.1.629.200.4.3.1.6
The name of the file to be transferred by this TFTP session.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcTftpSessFileSize 1.3.6.1.4.1.629.200.4.3.1.7
The number of bytes in the file. Whichever side has the file being sent may report the file size here. Not supported value: -1
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcTftpSessProgress 1.3.6.1.4.1.629.200.4.3.1.8
The number of bytes successfully transferred in this session. Not supported value: -1
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcTftpSessAddressType 1.3.6.1.4.1.629.200.4.3.1.9
This is the IP Address Type of the TFTP Host (Server/Client) serving the TFTP session as a source/destination.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nbsCmmcTftpSessAddress 1.3.6.1.4.1.629.200.4.3.1.10
This is the IPv4 or IPv6 Address of the TFTP Host (Server/Client) serving the TFTP session as a source/destination. Setting the nbsCmmcTftpSessAddress value will change also the the default of all the instances of nbsCmmcTftpSessAddress that were not specifically initialized by a SET operation. This supercedes nbsCmmcTftpSessHostIp.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nbsCmmcSysTftpHostAddressType 1.3.6.1.4.1.629.200.4.4
Address type of nbsCmmcSysTftpHostAddress.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nbsCmmcSysTftpHostAddress 1.3.6.1.4.1.629.200.4.5
Supercedes the previous value of nbsCmmcSysTftpHostIP; this is the IP Address of the TFTP Server/Client serving the actual TFTP transfer. A TFTP transfer may mean a software/microcode/parameter/etc.. download/upload process, initiated by the SNMP agent, for one of the modules, including, but not only, the System Control Card. It is unknown, if the TFTP host is undefined.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nbsCmmcChassisTable 1.3.6.1.4.1.629.200.6.1
A table that describes the Chassis connected
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcChassisEntry

nbsCmmcChassisEntry 1.3.6.1.4.1.629.200.6.1.1
Contains a description of a particular Chassis
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcChassisEntry  

nbsCmmcChassisIndex 1.3.6.1.4.1.629.200.6.1.1.1
The index of the Chassis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcChassisType 1.3.6.1.4.1.629.200.6.1.1.2
The type of Chassis.
Status: current Access: read-only
OBJECT-TYPE    
  NbsCmmcEnumChassisType  

nbsCmmcChassisModel 1.3.6.1.4.1.629.200.6.1.1.3
The model name of the chassis.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcChassisObjectId 1.3.6.1.4.1.629.200.6.1.1.4
Object Id of chassis.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

nbsCmmcChassisNumberOfSlots 1.3.6.1.4.1.629.200.6.1.1.5
The number of slots in the Chassis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcChassisHardwareRevision 1.3.6.1.4.1.629.200.6.1.1.6
The hardware revision of the chassis.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

nbsCmmcChassisPS1Status 1.3.6.1.4.1.629.200.6.1.1.7
The status of Power Supply 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInstalled(1), acBad(2), dcBad(3), acGood(4), dcGood(5), notSupported(6), good(7), bad(8)  

nbsCmmcChassisPS2Status 1.3.6.1.4.1.629.200.6.1.1.8
The status of Power Supply 2.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInstalled(1), acBad(2), dcBad(3), acGood(4), dcGood(5), notSupported(6), good(7), bad(8)  

nbsCmmcChassisPS3Status 1.3.6.1.4.1.629.200.6.1.1.9
The status of Power Supply 3.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInstalled(1), acBad(2), dcBad(3), acGood(4), dcGood(5), notSupported(6), good(7), bad(8)  

nbsCmmcChassisPS4Status 1.3.6.1.4.1.629.200.6.1.1.10
The status of Power Supply 4.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInstalled(1), acBad(2), dcBad(3), acGood(4), dcGood(5), notSupported(6), good(7), bad(8)  

nbsCmmcChassisFan1Status 1.3.6.1.4.1.629.200.6.1.1.11
The status of Fan 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), bad(2), good(3), notInstalled(4)  

nbsCmmcChassisFan2Status 1.3.6.1.4.1.629.200.6.1.1.12
The status of Fan 2.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), bad(2), good(3), notInstalled(4)  

nbsCmmcChassisFan3Status 1.3.6.1.4.1.629.200.6.1.1.13
The status of Fan 3.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), bad(2), good(3), notInstalled(4)  

nbsCmmcChassisFan4Status 1.3.6.1.4.1.629.200.6.1.1.14
The status of Fan 4.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), bad(2), good(3), notInstalled(4)  

nbsCmmcChassisTemperature 1.3.6.1.4.1.629.200.6.1.1.15
The temperature (degrees Celsius) of the Chassis. Not supported value: 0x80000000
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

nbsCmmcChassisTemperatureLimit 1.3.6.1.4.1.629.200.6.1.1.16
The maximum safe temperature (degrees Celsius) of the Chassis. Not supported value: 0x80000000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -100..100  

nbsCmmcChassisTemperatureMin 1.3.6.1.4.1.629.200.6.1.1.17
The minimum safe temperature (degrees Celsius) of the Chassis. Not supported value: 0x80000000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -100..100  

nbsCmmcChassisSignalStrength 1.3.6.1.4.1.629.200.6.1.1.18
The received signal strength.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcChassisSignalStrengthMinimum 1.3.6.1.4.1.629.200.6.1.1.19
The minimum recommended operational received signal strength.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcChassisEnableAutoReset 1.3.6.1.4.1.629.200.6.1.1.20
Continuously monitor slots for module changes, and reset if new board installed. Deprecated. The response to any GET should be notSupported(1). Any SET attempt should be rejected with the SNMP error badValue(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), deprecatedoff(2), deprecatedon(3)  

nbsCmmcChassisEnableLinkTraps 1.3.6.1.4.1.629.200.6.1.1.21
When set, send trap to report change in link status, up or down.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisEnableChassisTraps 1.3.6.1.4.1.629.200.6.1.1.22
When set, send trap to report chassis related events.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisEnableLoopbackTraps 1.3.6.1.4.1.629.200.6.1.1.23
When set, send trap to report change in loopback configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisEnableSlotChangeTraps 1.3.6.1.4.1.629.200.6.1.1.24
When set, send trap to report slot change related events.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisEnablePortTraps 1.3.6.1.4.1.629.200.6.1.1.25
When set, send trap to report port change related events.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisResetAllModules 1.3.6.1.4.1.629.200.6.1.1.26
Continuously monitor slots for module changes, and reset if new board installed. Deprecated. The response to any GET should be notSupported(1). Any SET attempt should be rejected with the SNMP error badValue(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), deprecatedOperating(2), deprecatedReset(3)  

nbsCmmcChassisEnableModuleSpecificTraps 1.3.6.1.4.1.629.200.6.1.1.27
When set, send trap to report change in specific cards conditions
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisLoopbackTimeout 1.3.6.1.4.1.629.200.6.1.1.28
loopback timeout in minutes, zero indicates forever
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

nbsCmmcChassisPortInfoBitMap 1.3.6.1.4.1.629.200.6.1.1.29
Deprecated.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nbsCmmcChassisSlotListBitMap 1.3.6.1.4.1.629.200.6.1.1.30
Deprecated.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nbsCmmcChassisNumberOfPortsBitMap 1.3.6.1.4.1.629.200.6.1.1.31
Deprecated.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nbsCmmcChassisName 1.3.6.1.4.1.629.200.6.1.1.32
The user assigned name for this chassis
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcChassisEnableLINTraps 1.3.6.1.4.1.629.200.6.1.1.33
When off(2), suppresses any traps related to Link Integrity Notification.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisEnablePortChangeTraps 1.3.6.1.4.1.629.200.6.1.1.34
When off(2), suppresses any traps related to removable Ports being inserted or removed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisEnablePortDiagsTraps 1.3.6.1.4.1.629.200.6.1.1.35
When off(2), suppresses any traps related to digital diagnostics being outside of safe levels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisFan5Status 1.3.6.1.4.1.629.200.6.1.1.36
The status of Fan 5.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), bad(2), good(3), notInstalled(4)  

nbsCmmcChassisFan6Status 1.3.6.1.4.1.629.200.6.1.1.37
The status of Fan 6.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), bad(2), good(3), notInstalled(4)  

nbsCmmcChassisFan7Status 1.3.6.1.4.1.629.200.6.1.1.38
The status of Fan 7.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), bad(2), good(3), notInstalled(4)  

nbsCmmcChassisFan8Status 1.3.6.1.4.1.629.200.6.1.1.39
The status of Fan 8.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), bad(2), good(3), notInstalled(4)  

nbsCmmcChassisEnableSwitchoverTraps 1.3.6.1.4.1.629.200.6.1.1.40
When on, NM can send notifications whenever a self-healing card switches traffic from an active port to its redundant standby port. When off, NM will not send switchover notifications.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcChassisCrossConnect 1.3.6.1.4.1.629.200.6.1.1.41
For chassis housing cross-connect blades or slots, this object is used to reflect the operating state and to clear the entire cross-connect map, including any independent maps of subordinate slots. If there are currently no cross-connect blades or slots in this chassis, the Agent must report notSupported(1). Additionally, if this object reports notSupported(1), any SNMP SET to this object should return SNMP Error 3 (bad value). The Agent should report operating(2) under normal circumstances. If this object reports operating(2), SNMP Managers are allowed to set this object to clearing (3), which instructs the Agent to erase all this chassis' cross-connect maps, including any independent maps of subordinate slots.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), operating(2), clearing(3)  

nbsCmmcChassisNVAreaBanks 1.3.6.1.4.1.629.200.6.1.1.42
The maximum number of executable images that can be stored locally on this chassis. This number does not count any memory banks that are in a modular subcomponent of this chassis. Please refer to nbsPartProgNVAreaStart and nbsPartProgNVAreaBanks for that information. Not supported value: 0
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcChassisFirmwareCaps 1.3.6.1.4.1.629.200.6.1.1.43
This bitmask indicates which executable images this chassis can support. This object is mandatory for all chassis. Bit 0 is reserved. Subsequent bits refer to the nbsCmmcSysFirmwareTable. Bit 1 corresponds to the first table entry, Bit 2 to the second entry, and so on. A bit is set (1) if that image is appropriate for this chassis, cleared (0) otherwise. OCTET STRING bitmasks count the leftmost bit (MSB) as 0. A zero length OCTET STRING indicates that the nbsCmmcSysFirmwareTable is not supported by this agent.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

nbsCmmcChassisFirmwareLoad 1.3.6.1.4.1.629.200.6.1.1.44
This bitmask indicates which executable images this chassis has stored in its own NV area. This object is mandatory for all chassis. OCTET STRING bitmasks count the leftmost bit (MSB) as 0. Bit 0 indicates whether an executable image is loading. Subsequent bits refer to the nbsCmmcSysFirmwareTable. Bit 1 corresponds to the first table entry, Bit 2 to the second entry, and so on. A bit is set (1) if that image is stored on this chassis, cleared (0) if not. Clearing bits has no effect. To erase an NV area, use the nbsCmmcSysNVAreaTable. Users may transfer a file to an NV area by setting the appropriate file's bit and the loading (MSB) bit to one (1). Adding a file requires that the NM start a file transfer to this chassis, which is a lengthy operation. If a transfer session is already active (nbsCmmcChassisLoader is non-zero), writes to this object will be rejected. A zero length OCTET STRING indicates that the nbsCmmcSysFirmwareTable is not supported by this agent.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

nbsCmmcChassisNVAreaAdmin 1.3.6.1.4.1.629.200.6.1.1.45
A SET on this object will force the corresponding nbsCmmcSysNvAreaStatus to primary, set this chassis' other memory banks to backup, and immediately load and execute the firmware image contained in the specified memory bank. A GET on this object will indicate the memory bank of this chassis that is currently designated as primary. Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcChassisNVAreaOper 1.3.6.1.4.1.629.200.6.1.1.46
The nbsCmmcSysNVAreaBank of nbsCmmcSysNVAreaTable corresponding to the current operationally active firmware image. 0 indicates the current active image is NOT in the NVAreaTable. Not supported value: -1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcChassisLoader 1.3.6.1.4.1.629.200.6.1.1.47
The nbsCmmcSysLoaderIndex of nbsCmmcSysLoaderTable corresponding to the current loading session. 0 indicates no loading session is active.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcChassisSerialNum 1.3.6.1.4.1.629.200.6.1.1.48
SerialNumber of this chassis. If this object is not supported, this string should be empty.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

nbsCmmcChassisFace 1.3.6.1.4.1.629.200.6.1.1.49
ASCII string containing encoded summary of chassis front panel status. The encoding uses keywords and associated allowed values. Keyword:value pairs delimited by the pipe '|' symbol, and within a pair, a keyword should be separated from its associated value by a colon ':' character. Agent should provide the following info if available. If unknown, it should be omitted. Description Keyword Allowed Values --------------------------------------------------------- Protocol prot ether|slip Power Supply(X) psx [use nbsCmmcChassisPSxStatus] Temperature temp [use nbsCmmcChassisTemperature] Temperature Max tmax [use nbsCmmcChassisTemperatureLimit] Temperature Min tmin [use nbsCmmcChassisTemperatureMin] Type type [use nbsCmmcChassisType] RM/AH Peer Chas rmch [use nbsCmmcChassisIndex] An example string could be: |prot:ether|ps1:2|ps2:3|ps3:5|temp:20| If this object is not supported, this string should be empty.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..500)  

nbsCmmcChassisCountersState 1.3.6.1.4.1.629.200.6.1.1.50
This object allows user to reset MAC counters on all ports in this Chassis.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), counting(2), clearing(3)  

nbsCmmcChassisPowerStatus 1.3.6.1.4.1.629.200.6.1.1.51
Indicates if the total power in the chassis is sufficient or insufficient. Insufficient means that the chassis won't work in a correct mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), sufficient(2), insufficient(3)  

nbsCmmcChassisIfIndex 1.3.6.1.4.1.629.200.6.1.1.52
Mib2-like ifIndex of this chassis
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

nbsCmmcChassisCount 1.3.6.1.4.1.629.200.6.2
The number of chassis currently plugged into the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotTable 1.3.6.1.4.1.629.200.7.1
A table that describes the Slot connected
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSlotEntry

nbsCmmcSlotEntry 1.3.6.1.4.1.629.200.7.1.1
Contains a description of a particular Slot
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSlotEntry  

nbsCmmcSlotChassisIndex 1.3.6.1.4.1.629.200.7.1.1.1
The index of the Chassis to the Slot is connected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotIndex 1.3.6.1.4.1.629.200.7.1.1.2
The slot index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotType 1.3.6.1.4.1.629.200.7.1.1.3
The front panel of card in the slot.
Status: current Access: read-only
OBJECT-TYPE    
  NbsCmmcEnumSlotType  

nbsCmmcSlotModel 1.3.6.1.4.1.629.200.7.1.1.4
Describes the model of card that is currently in the slot.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcSlotObjectId 1.3.6.1.4.1.629.200.7.1.1.5
The description of the type of card in the slot.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

nbsCmmcSlotNumberOfPorts 1.3.6.1.4.1.629.200.7.1.1.6
Number of ports on the card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotHardwareRevision 1.3.6.1.4.1.629.200.7.1.1.7
This describes the hardware revision of the card
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

nbsCmmcSlotOperationType 1.3.6.1.4.1.629.200.7.1.1.8
Operation of card..
Status: current Access: read-write
OBJECT-TYPE    
  NbsCmmcEnumSlotOperationType  

nbsCmmcSlotReset 1.3.6.1.4.1.629.200.7.1.1.9
Current reset condition, and possible reset types. notSupported [1] - reported if feature unavailable. operating [2] - indicates normal operating status. phy [3] and queue [4] are deprecated. resetSlot [5] - cold restart, may impact traffic. initSlot [6] reverts to default settings; init-module. resetWarm [7] - soft restart, won't hurt traffic. The value operating [2] is normally returned by GET, but during a reset operation, the appropriate reset value [5, 6, or 7] may be returned.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), operating(2), deprecatedPhy(3), deprecatedQueue(4), resetSlot(5), initSlot(6), resetWarm(7)  

nbsCmmcSlotName 1.3.6.1.4.1.629.200.7.1.1.10
The user assigned name for this slot.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcSlotModuleType 1.3.6.1.4.1.629.200.7.1.1.11
Equivalent to nbsCmmcSlotType, except for modules that occupy more than one slot in a chassis. For such multi- slot modules, this ModuleType indicates the product this slot is a part of.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotModuleSlot 1.3.6.1.4.1.629.200.7.1.1.12
This indicates the position of this slot within its module. For one-slot modules this value is always one (1). For multi-slot modules, this is a positive integer between 1 and the number of slots spanned by this module. The numbering always begins with the leftmost slot as 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotSwConfigurable 1.3.6.1.4.1.629.200.7.1.1.13
Indicates whether card is software configurable, usually based on hardware jumper/dip switch settings. If any changes to the hardware configuration are allowed, this value will be yes(3). If this is no(2), SNMP GETs will work but SETs will fail with an SNMP error. According to RFC 1157, that error should be noSuchName(2).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), no(2), yes(3)  

nbsCmmcSlotConfiguration 1.3.6.1.4.1.629.200.7.1.1.14
Bit stream containing current configuration of slot.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..250)  

nbsCmmcSlotMacAddress 1.3.6.1.4.1.629.200.7.1.1.15
MAC Address of this card. If this object is not supported, this string should be empty.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..6)  

nbsCmmcSlotIPAddress 1.3.6.1.4.1.629.200.7.1.1.16
For non-NM cards which feature independent IP stacks, this is the SNMP Agent Administrative value of the IP Address for the card in this slot.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSlotSubnetMask 1.3.6.1.4.1.629.200.7.1.1.17
For non-NM cards which feature independent IP stacks, this is the SNMP Agent Administrative value of the SubnetMask for the card in this slot.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSlotBroadcastAddr 1.3.6.1.4.1.629.200.7.1.1.18
For non-NM cards which feature independent IP stacks, this is the SNMP Agent Administrative value of the IP Broadcast Address for the card in this slot.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSlotDefGateway 1.3.6.1.4.1.629.200.7.1.1.19
For non-NM cards which feature independent IP stacks, this is the SNMP Agent Administrative value of the Default Gateway for the card in this slot.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSlotHoming 1.3.6.1.4.1.629.200.7.1.1.20
This object describes the cabling topology of CO / CPE pairs. It must be supported on the Customer Premises Equipment (CPE) slots. Any card that does not utilize this object should report notSupported(1). If one CO is redundantly cabled to one CPE, the pair is in singleCO(2) homing. If two separate CO cards are connected to the same CPE, the CPE is dually homed. Because neither CO has contact with the other CO, each CO should be told the CPE is in a dualCOs(3) homing configuration. If the card has a dual homing feature but does not know its current status, it defaults to singleCO(2). If that is incorrect, users should change the value to dualCOs(3) to inform the card of its network configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), singleCO(2), dualCOs(3)  

nbsCmmcSlotRedundancyAdmin 1.3.6.1.4.1.629.200.7.1.1.21
This object is used to disable redundancy on certain cards that support the 802.3ah standard, but if supported, the preferred method is to use the object nbsCmmcPortEnableAdmin to administratively disable redundant ports that shouldn't become active. This object may also be used to change the operating mode of 4 port crossbar cards that can be configured for redundancy. For cards that do not support this feature, any reads of this object should get the response notSupported (1). Writes to this object should be rejected with the SNMP error badValue (3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSlotDescr 1.3.6.1.4.1.629.200.7.1.1.22
Agent description of this slot.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

nbsCmmcSlotUpgradable 1.3.6.1.4.1.629.200.7.1.1.23
This object indicates whether the card in this slot can now be reprogrammed. It should be used together with nbsCmmcSysUpgrade. Cards without reprogrammable firmware should always report notSupported (1). Reprogrammable cards should report supported(2) only if the NM has the appropriate firmware image already loaded and ready to send to the card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), supported(2)  

nbsCmmcSlotCrossConnect 1.3.6.1.4.1.629.200.7.1.1.24
For slots supporting cross-connect functionality, this object is used to reflect the operating state and clear the entire cross-connect map for this slot. If the slot is not of cross-connect type, the Agent must report notSupported(1). Additionally, if this object reports notSupported(1), any SNMP SET to this object should return SNMP Error 3 (bad value). The Agent should report operating(2) under normal circumstances. If this object reports operating(2), SNMP Managers are allowed to set this object to clearing (3), which instructs the Agent to erase the cross-connect map for this slot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), operating(2), clearing(3)  

nbsCmmcSlotClearType 1.3.6.1.4.1.629.200.7.1.1.25
When nbsCmmcSysLockTypes is enabled, use this object to clear the configured slot type. Issue a set command with a value of clearType(3). A read of this object will always return idle(2), or notSupported(1) if this feature is not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), idle(2), clearType(3)  

nbsCmmcSlotNVAreaBanks 1.3.6.1.4.1.629.200.7.1.1.26
The maximum number of executable images that can be stored locally on this module. This number does not count any memory banks that are in a modular subcomponent of this card. Please refer to nbsPartProgNVAreaStart and nbsPartProgNVAreaBanks for that information. Not supported value: 0
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotFirmwareCaps 1.3.6.1.4.1.629.200.7.1.1.27
This bitmask indicates which executable images this module can support. This object is mandatory for all modules. Bit 0 is reserved. Subsequent bits refer to the nbsCmmcSysFirmwareTable. Bit 1 corresponds to the first table entry, Bit 2 to the second entry, and so on. A bit is set (1) if that image is appropriate for this module, cleared (0) if unavailable. OCTET STRING bitmasks count the leftmost bit (MSB) as 0. A zero length OCTET STRING indicates that the nbsCmmcSysFirmwareTable is not supported by this agent.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

nbsCmmcSlotFirmwareLoad 1.3.6.1.4.1.629.200.7.1.1.28
This bitmask indicates which executable images this module has stored in its own NV area. This object is mandatory for all modules. OCTET STRING bitmasks count the leftmost bit (MSB) as 0. Bit 0 indicates whether an executable image is loading. Subsequent bits refer to the nbsCmmcSysFirmwareTable. Bit 1 corresponds to the first table entry, Bit 2 to the second entry, and so on. A bit is set (1) if that image is stored on this module, cleared (0) if not. Clearing bits has no effect. To erase an NV area, use the nbsCmmcSysNVAreaTable. Users may transfer a file to an NV area by setting the appropriate file's bit and the loading (MSB) bit to one (1). Adding a file requires that the NM start a file transfer to this module, which is a lengthy operation. If a transfer session is already active (nbsCmmcSlotLoader is non-zero), writes to this object will be rejected. A zero length OCTET STRING indicates that the nbsCmmcSysFirmwareTable is not supported by this agent.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

nbsCmmcSlotNVAreaAdmin 1.3.6.1.4.1.629.200.7.1.1.29
A SET on this object will force the corresponding nbsCmmcSysNvAreaStatus to primary, set this module's other memory banks to backup, and immediately load and execute the firmware image contained in the specified memory bank. A GET on this object will indicate the memory bank of this module that is currently designated as primary. Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotNVAreaOper 1.3.6.1.4.1.629.200.7.1.1.30
The nbsCmmcSysNVAreaBank of nbsCmmcSysNVAreaTable corresponding to the current operationally active firmware image. 0 indicates the current active image is NOT in the NVAreaTable. Not supported value: -1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotLoader 1.3.6.1.4.1.629.200.7.1.1.31
The nbsCmmcSysLoaderIndex of nbsCmmcSysLoaderTable corresponding to the current loading session. 0 indicates no loading session is active.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotSerialNum 1.3.6.1.4.1.629.200.7.1.1.32
SerialNumber of this module. If this object is not supported, this string should be empty.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

nbsCmmcSlotToggleRate 1.3.6.1.4.1.629.200.7.1.1.33
For crossbar products. Used to indicate the approximate rate, in microseconds, at which this card should toggle its transmitters on and off. Not supported value: 0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

nbsCmmcSlotTemperature 1.3.6.1.4.1.629.200.7.1.1.34
The temperature (in degrees celsius) of this slot. Not supported value: 0x80000000
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

nbsCmmcSlotCountersState 1.3.6.1.4.1.629.200.7.1.1.35
This object allows user to reset MAC counters on all ports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), counting(2), clearing(3)  

nbsCmmcSlotRedundancyOper 1.3.6.1.4.1.629.200.7.1.1.36
This object reports the actual redundancy state of a card. For cards that do not support this feature, any reads of this object should get the response notSupported (1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcSlotIfIndex 1.3.6.1.4.1.629.200.7.1.1.37
Mib2-like ifIndex of this slot
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

nbsCmmcSlotModuleStatus 1.3.6.1.4.1.629.200.7.1.1.38
Slots that have no card installed should be reported as empty(2). Slots where a card has been physically inserted should be reported as notReady(3) while the card is loading or warming up, and ready(4) once the card is fully operational. Slots that support redundant action may report standby(5) if they are not yet ready but waiting to go to ready(4) in case of failover. When this object is unavailable the Agent will report the status notSupported (1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), empty(2), notReady(3), ready(4), standby(5)  

nbsCmmcLedTable 1.3.6.1.4.1.629.200.7.2
A table to report status of front panel LEDs
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcLedEntry

nbsCmmcLedEntry 1.3.6.1.4.1.629.200.7.2.1
Indicates status of a particular LED
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcLedEntry  

nbsCmmcLedChassisIndex 1.3.6.1.4.1.629.200.7.2.1.1
The index of the Chassis to the Slot is connected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcLedSlotIndex 1.3.6.1.4.1.629.200.7.2.1.2
The slot index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcLedIndex 1.3.6.1.4.1.629.200.7.2.1.3
The index of the led. Index starts at 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcLedColor 1.3.6.1.4.1.629.200.7.2.1.4
Actual/current color of the LED.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(1), green(2), amber(3), other(4)  

nbsCmmcLedDescription 1.3.6.1.4.1.629.200.7.2.1.5
LED's label as on card and short description
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcSlotFaceTable 1.3.6.1.4.1.629.200.7.3
A table that describes the front panel state of each slot
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSlotFaceEntry

nbsCmmcSlotFaceEntry 1.3.6.1.4.1.629.200.7.3.1
Contains a description of a particular Slot
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSlotFaceEntry  

nbsCmmcSlotFaceChassisIndex 1.3.6.1.4.1.629.200.7.3.1.1
The index of the Chassis housing this slot.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotFaceSlotIndex 1.3.6.1.4.1.629.200.7.3.1.2
The slot index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotFaceRowIndex 1.3.6.1.4.1.629.200.7.3.1.3
Row Number
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSlotFaceSummary 1.3.6.1.4.1.629.200.7.3.1.4
ASCII string containing encoded summary of slot front panel status. The encoding uses keywords and associated allowed values. Keyword:value pairs delimited by the pipe '|' symbol, and within a pair, a keyword should be separated from its associated value by a colon ':' character. Agent should provide the following info if available. If unknown or inapplicable, it should be omitted. Description Keyword Allowed Values --------------------------------------------------------- Slot/SNMP Type slid [use nbsCmmcSlotType] LED ledx [use nbsCmmcLedColor] PortLink plnkx [use nbsCmmcPortLinked] PortOperational popx [use nbsCmmcPortOperational] PortSelectLink pselx actv|stdby PortConnector pconx [use nbsCmmcPortConnector] An example string could be: |slid:436|led1:2|plnk1:2|pop2:2|psel2:actv|pcon4:15| If this object is not supported, this string should be empty.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..500)  

nbsCmmcPortTable 1.3.6.1.4.1.629.200.8.1
A table that describes the Port connected
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcPortEntry

nbsCmmcPortEntry 1.3.6.1.4.1.629.200.8.1.1
Contains a description of a particular Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcPortEntry  

nbsCmmcPortChassisIndex 1.3.6.1.4.1.629.200.8.1.1.1
The index of the Chassis for the Slot to which this port is connected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortSlotIndex 1.3.6.1.4.1.629.200.8.1.1.2
The index of the Slot in the Chassis to which this port is connected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortIndex 1.3.6.1.4.1.629.200.8.1.1.3
The index of the Port in the Slot in the Chassis to which this port is connected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortType 1.3.6.1.4.1.629.200.8.1.1.4
The physical type of port. Valid port types are > 1. The mib representation of pluggable port types are documented in nbsSffMsaIdentifier from NBS-SFF-MIB, and have the following PortTypes here: sfp 125, gbic 147, xfp 197, qsfp 219, cxp 220, cfp 221, qspf28 223, cfp2 224
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortObjectId 1.3.6.1.4.1.629.200.8.1.1.5
Object Id of the port
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  


nbsCmmcPortAutoNegotiation 1.3.6.1.4.1.629.200.8.1.1.7
The AutoNegotiation status of a port. AutoNegotiation may affect the port's speed, duplex, and MDI/MDIX. If this port does not offer this feature, Agent should report the value notSupported(1). To disable this feature, set the value to off(2). To enable this feature, set the value to on(3). The value autoMDIXOnly(4) is deprecated. The value custom (5) is deprecated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3), deprecated4(4), deprecated5(5)  

nbsCmmcPortDuplex 1.3.6.1.4.1.629.200.8.1.1.8
The duplex mode of the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), half(2), full(3)  

nbsCmmcPortSpeed 1.3.6.1.4.1.629.200.8.1.1.9
The line speed of the port. This object is superseded by nbsCmmcPortProtoAdmin and nbsCmmcPortProtoOper.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), spd10Mbps(2), spd100Mbps(3), spdGigabit(4), spd10Gbps(5)  

nbsCmmcPortRxActivity 1.3.6.1.4.1.629.200.8.1.1.10
The receive status of the port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcPortTxActivity 1.3.6.1.4.1.629.200.8.1.1.11
The transmit status of the port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcPortCollisionActivity 1.3.6.1.4.1.629.200.8.1.1.12
The collision status of the port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcPortLoopback 1.3.6.1.4.1.629.200.8.1.1.13
The loopback status of the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcPortEnableAdmin 1.3.6.1.4.1.629.200.8.1.1.14
Administratively desired operational status of the port. For the actual operational status, please see the related object nbsCmmcPortEnableOper. The value notSupported (1) indicates that the user has no ability to disable the transceiver. Users may set this value to disable (2) to turn off the port's transceiver so that no traffic will flow through this port. For traffic to be sent and received as normal, this object should be set to enable (3). The value auto (4) has been deprecated - older Agents might report it, and Managers may attempt to set it, but newer agents will neither report nor accept this value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disable(2), enable(3), deprecatedAuto(4)  


nbsCmmcPortLIN 1.3.6.1.4.1.629.200.8.1.1.16
Line integrity check on or off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disable(2), enable(3)  

nbsCmmcPortAging 1.3.6.1.4.1.629.200.8.1.1.17
Aging on or off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcPortMaxPacketSize 1.3.6.1.4.1.629.200.8.1.1.18
The Maximum Packet Size Allowed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), max1518(2), max1536(3), max6k(4)  

nbsCmmcPortRemoteLoopback 1.3.6.1.4.1.629.200.8.1.1.19
Indicates whether port should perform Remote Loopback. When on (3), outbound traffic is returned to the ingress port. In other words, traffic comes from one of the module's other ports to get to this one, and upon arriving here gets sent back to that other port, from where it continues on back to the originator of the traffic. The related object nbsCmmcPortLoopback may be forced off(2) whenever this object is set to on(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcPortErrorActivity 1.3.6.1.4.1.629.200.8.1.1.20
The error activity of the port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcPortName 1.3.6.1.4.1.629.200.8.1.1.21
The user assigned name for this port. This object is also used for the MIB2 object ifAlias.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcPortValue 1.3.6.1.4.1.629.200.8.1.1.22
Originally named nbsCmmcPortOpticalPower. Now usage may vary by card. For card 162, PortValue measures the Optical Power, or signal strength. For card 197, PortValue is a text string displaying signal strength in decibels. For cards 211 and 212, PortValue measures the current bandwidth level. Only one byte is used, and its value can be notSupported(1), under45Mbps(2), under155Mbps(3), under622Mbps(4), or under1Gbps(5)
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

nbsCmmcPortThreshold 1.3.6.1.4.1.629.200.8.1.1.23
Port Threshold - usage may be different for each card. For card 197, this indicates the minimum signal strength. Value ranges from -5 to -40 decibels. For card 211, valid values are: notSupported(1), speed45Mbps(2), speed155Mbps(3), speed622Mbps(4), speed1Gbps(5) For card 375, this indicates the rate limit and is expressed in units of Mbps. For cards 376 and 379, this indicates the rate limit and is expressed in units of Kbps. Not supported value: 0x80000000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

nbsCmmcPortThresholdAction 1.3.6.1.4.1.629.200.8.1.1.24
Action to perform if threshold is crossed. Usage may be different for each card. For card 197, the allowable Actions are: notSupported(1), noAction(2), sendTrap(3) For cards 211 and 212, valid values are: notSupported(1), noAction(2), sendTrap(3), disablePort(4), disablePortAndSendTrap(5),disablePortPeriodically(6), disablePeriodicallyAndSendTrap(7) Not supported value: 1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortRMChassis 1.3.6.1.4.1.629.200.8.1.1.25
The nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects indicate which remote port is externally cabled to this port. This nbsCmmcPortRMChassis object indicates the remote port's nbsCmmcPortChassisIndex. If no remote port is known, the nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects should each have the value 0. If a physical link is discovered by the agent, the nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects are each set automatically. If the connection is not discovered automatically, users may enter the connection by manually setting the three nbsCmmcPortRM objects
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortRMSlot 1.3.6.1.4.1.629.200.8.1.1.26
The nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects indicate which remote port is externally cabled to this port. This nbsCmmcPortRMSlot object indicates the remote port's nbsCmmcPortSlotIndex. If no remote port is known, the nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects should each have the value 0. If a physical link is discovered by the agent, the nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects are each set automatically. If the connection is not discovered automatically, users may enter the connection by manually setting the three nbsCmmcPortRM objects
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortRMPort 1.3.6.1.4.1.629.200.8.1.1.27
The nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects indicate which remote port is externally cabled to this port. This nbsCmmcPortRMPort object indicates the remote port's nbsCmmcPortIndex. If no remote port is known, the nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects should each have the value 0. If a physical link is discovered by the agent, the nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects are each set automatically. If the connection is not discovered automatically, users may enter the connection by manually setting the three nbsCmmcPortRM objects
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortSerialNumber 1.3.6.1.4.1.629.200.8.1.1.28
Part Serial Number as reported by the component. Not supported value: 'N/A'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcPortVendorInfo 1.3.6.1.4.1.629.200.8.1.1.29
Vendor name as reported by the component. Not supported value: 'N/A'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcPortTemperature 1.3.6.1.4.1.629.200.8.1.1.30
The temperature (in degrees celsius) of this trans- ceiver. Not supported value: 0x80000000
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

nbsCmmcPortTxPower 1.3.6.1.4.1.629.200.8.1.1.31
The output power (in milli dBm) of this transmitter. Not supported value: 0x80000000
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

nbsCmmcPortRxPower 1.3.6.1.4.1.629.200.8.1.1.32
The received optical power (in milli dBm) of this receiver. Not supported value: 0x80000000
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

nbsCmmcPortBiasAmps 1.3.6.1.4.1.629.200.8.1.1.33
The bias current (in microAmps) of this transmitter. The reserved value -1 indicates that this object is not supported.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortSupplyVolts 1.3.6.1.4.1.629.200.8.1.1.34
The supply voltage (in milliVolts) of this transmitter. The reserved value -1 indicates that this object is not supported.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortMedium 1.3.6.1.4.1.629.200.8.1.1.35
The type of physical communications medium.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), coax(2), twistedPair(3), singleMode(4), multiMode(5)  

nbsCmmcPortConnector 1.3.6.1.4.1.629.200.8.1.1.36
The type of physical connector or jack.
Status: current Access: read-only
OBJECT-TYPE    
  NbsCmmcEnumPortConnector  

nbsCmmcPortWavelength 1.3.6.1.4.1.629.200.8.1.1.37
The output wavelength (in nanoMeters) of this transmitter. The reserved value -1 indicates that this object is not supported. This object has been superseded by nbsCmmcPortWavelengthX, which supports floating point wavelengths, and lists of wavelengths.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortDigitalDiags 1.3.6.1.4.1.629.200.8.1.1.38
Indicates whether Digital Diagnostics are supported by this port. If they are supported, this variable indicates the worst severity level among the measured diagnostic values.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), diagsOk(2), diagsWarning(3), diagsAlarm(4)  

nbsCmmcPortZoneIdAdmin 1.3.6.1.4.1.629.200.8.1.1.39
For Fibre Channel products, this will be the Agent-assigned ZoneId of the zone this port belongs to. For products which allow dynamic configuration of converter circuits, this will be the Port number where data for this converter circuit will be received. If the chassis or slot is changing, they should be SET first, so ZoneIdAdmin is SET last. This signals the Agent to reconfigure the crossbar. The value 0 indicates that this port is not a part of any Fibre Channel Zone or converter circuit. In order for two ports to be in the same zone/circuit, each must be configured to the same PortSpeed or BitRate. If the Agent receives a request to set CircuitRxPort to a port with a different bit rate, the Agent will return SNMP error-status badValue (3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortNominalBitRate 1.3.6.1.4.1.629.200.8.1.1.40
This NominalBitRate variable exists for modules which support configurable speeds that may not be listed in PortSpeed. Here can be specified the raw bit rate desired, measured in decimal Mbps. The Agent may use exactly that rate, or may substitute it with a compatible rate within an appropriate range of speeds. If the Agent receives a request for a bitrate it cannot support, it should return the SNMP errorstatus badValue(3). For ports whose speed is unknown or not configurable, the Agent should report this value as -1. The reserved value 0 specifies that no speed is configured, and any clocking is bypassed. The following values are associated with specific protocols: 44 - DS3 51 - OC-1 77 - Telco bus 125 - Fast Ethernet (100 Mbps) 126 - FDDI 155 - OC-3 200 - ESCON 270 - SDI 270Mbps 540 - SDI 540Mbps 622 - OC-12 1063 - 1 Gig FibreChannel 1244 - OC-24 1250 - Gigabit Ethernet 1485 - HDTV 2125 - 2 Gig FibreChannel 2450 - OC-48 2500 - Infiniband 2666 - OC-48+FEC 9953 - 10 Gig Ethernet/WAN 10312 - 10 Gig Ethernet/LAN 10625 - 10 Gig FibreChannel For ports that support ProtoAdmin 'userDefined', writing this object will automatically set the ProtoAdmin to 'userDefined'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortModulePort 1.3.6.1.4.1.629.200.8.1.1.41
Similar to SlotModuleSlot. Some modules occupy more than one slot of a chassis. For such products, this variable will report the port number from the Module perspective. In contrast, the PortIndex reports the port number from an individual slot's perspective. For modules that occupy only one slot, PortModulePort will be equivalent to PortIndex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortPartRev 1.3.6.1.4.1.629.200.8.1.1.42
Part Number and Revision level as reported by the component. Not supported value: 'N/A'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcPortIfIndex 1.3.6.1.4.1.629.200.8.1.1.43
The index to the MIB-II Interface table entry which represents this port. If there is no corresponding MIB-II interface entry, this value should be 0.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortLinked 1.3.6.1.4.1.629.200.8.1.1.44
Simpler, one bit version of PortLink. The value no(1) means there is no signal detected or that signal is of poor quality. The value yes(2) indicates a good connection.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nbsCmmcPortOperational 1.3.6.1.4.1.629.200.8.1.1.45
Indicates whether the port is in a state appropriate for normal data communications. The value no(1) means that the port is disabled or in an abnormal state such as loopback. The value yes(2) indicates that the port is enabled and usable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nbsCmmcPortZoneChassisAdmin 1.3.6.1.4.1.629.200.8.1.1.46
For crossbar products, this is the Chassis housing the port shown in nbsCmmcPortZoneId.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortZoneSlotAdmin 1.3.6.1.4.1.629.200.8.1.1.47
For crossbar products, this is the Slot housing the port shown in nbsCmmcPortZoneId.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortAlarmCause 1.3.6.1.4.1.629.200.8.1.1.48
For Pluggable ports with Digital Diagnostics. If there is currently no alarm condition, this string should be empty. Otherwise, this should display the most severe actual alarm condition.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcPortFlowControl 1.3.6.1.4.1.629.200.8.1.1.49
This object determines whether FlowControl should be used. If disabled(2), no FlowControl will be initiated by this port. Any FlowControl requests received will be dropped. If enabled(3), this port will initiate and observe FlowControl requests as specified by the objects nbsCmmcPortFCRecvOper and nbsCmmcPortFCSendOper. Those settings may be changed through the related nbsCmmcPortFCSendAdmin and nbsCmmcPortFCRecvAdmin objects. If notSupported(1), this object is not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcPortAutoNegAd 1.3.6.1.4.1.629.200.8.1.1.50
This object determines which capabilities will be advertised during auto negotiation. Each capability is represented by one bit. Set bit to 1 to advertise capability, 0 to deny it. Capability Bit ---------------------- --- reserved 0 Flow Control 1 1000 Mbps Full Duplex 2 1000 Mbps Half Duplex 3 100 Mbps Full Duplex 4 100 Mbps Half Duplex 5 10 Mbps Full Duplex 6 10 Mbps Half Duplex 7 OCTET STRING bitmasks count the leftmost bit (MSB) as 0.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1)  

nbsCmmcPortAutoNegEditable 1.3.6.1.4.1.629.200.8.1.1.51
This object determines which AutoNegAd bits may be changed by the user. Bits set to 1 indicate user may choose whether to advertise the corresponding capability. Bits are cleared if user is not allowed to change the corresponding AutoNegAd bit. Capability Bit ---------------------- --- reserved 0 Flow Control 1 1000 Mbps Full Duplex 2 1000 Mbps Half Duplex 3 100 Mbps Full Duplex 4 100 Mbps Half Duplex 5 10 Mbps Full Duplex 6 10 Mbps Half Duplex 7 OCTET STRING bitmasks count the leftmost bit (MSB) as 0.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

nbsCmmcPortWavelengthX 1.3.6.1.4.1.629.200.8.1.1.52
This objects supersedes the nbsCmmcPortWavelength object. The string format allows both whole numbers as in CWDM, or floating-point numbers as in DWDM. If there is more than one wavelength, as with WDM trunks, each color should be listed, separated by commas. Not supported value: 'N/A'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..150)  

nbsCmmcPortZoneIdOper 1.3.6.1.4.1.629.200.8.1.1.53
Operational version of nbsCmmcPortZoneIdAdmin
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortZoneSlotOper 1.3.6.1.4.1.629.200.8.1.1.54
Operational version of nbsCmmcPortZoneSlotAdmin
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortZoneChassisOper 1.3.6.1.4.1.629.200.8.1.1.55
Operational version of nbsCmmcPortZoneChassisAdmin
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortLinkMatch 1.3.6.1.4.1.629.200.8.1.1.56
Some converter ports that are capable of autonegotiation (ANEG) may sometimes be between two end ports that would like to autonegotiate with each other. The Agent can ensure that both ports in the converter/circuit settle on the same autonegotiated settings. This feature is called LinkMatch. ANEG with LinkMatch can sometimes be a lengthy process. In order to streamline the ANEG process, users may manually configure the parameters that supporting ports will advertise during their independent autonegotiations. This involves two steps - first to change the nbsCmmcPortAutoNegAd object to reflect the outcome desired, then to set this nbsCmmcPortLinkMatch object to the value disabled(2). The default value for this object is enabled(3). Ports that do not support this feature should return the value notSupported(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcPortMDIPinoutAdmin 1.3.6.1.4.1.629.200.8.1.1.57
Connecting twisted-pair ethernet ports originally required care in choosing either straight or crossover cables. Later, many ethernet ports added the feature that they could be configured to accept either cable pinout. Some ports are even smart enough to detect, or autosense, the pinout they should use. This Administrative object allows users to request the port adopt a specific pinout, or to have the port autosense it. The value notSupported(1) indicates that this port cannot dynamically alter its pinout through this object. The value mdi(2) is used to connect with a straight cable to mdix ports such as those found on hubs, switches and routers. The value mdix(3) is used to connect with a straight cable to mdi ports such as those found on workstations. The value autoSense(4) indicates this port should automatically detect and change to the necessary pinout. This object has a corresponding Operational value which reports the actual pinout state. In certain situations, the Operational value might differ from the Administrative.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), mdi(2), mdix(3), autoSense(4)  

nbsCmmcPortMDIPinoutOper 1.3.6.1.4.1.629.200.8.1.1.58
This object reports the actual pinout state of an ethernet port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), mdi(2), mdix(3)  

nbsCmmcPortFCRecvAdmin 1.3.6.1.4.1.629.200.8.1.1.59
This object allows user to specify what this port should do if it receives a flow control request. This object is ignored when nbsCmmcPortFlowControl is disabled. If this object reports notSupported(1), no changes to this object are allowed. Setting this object to drop(2) indicates that this port should ignore requests to control its flow. Setting this object to comply(3) means this port should grant flow control requests from the connected port, and buffer up traffic while the other side catches up. If this object is set to passthru(4), the port will not comply with the request, but will relay it along to the next port. The corresponding nbsCmmcPortFCRecvOper object indicates the setting that is actually in effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), drop(2), comply(3), passThru(4)  

nbsCmmcPortFCRecvOper 1.3.6.1.4.1.629.200.8.1.1.60
This object indicates what this port will do with flow control requests it receives.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), drop(2), comply(3), passThru(4)  

nbsCmmcPortFCSendAdmin 1.3.6.1.4.1.629.200.8.1.1.61
This object specifies whether this port will send flow control requests when its in danger of dropping incoming packets. This object is ignored when nbsCmmcPortFlowControl is disabled. Setting this object to enabled(3) means this port may send flow control requests to the other port. Setting this object to disabled(2) indicates that this port should drop packets instead of sending flow control requests. If this object is set to notSupported(1), this object cannot be changed for this port. The corresponding nbsCmmcPortFCSendOper object indicates the setting that is actually in effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcPortFCSendOper 1.3.6.1.4.1.629.200.8.1.1.62
This object is ignored when nbsCmmcPortFlowControl is disabled. This object indicates whether or not this port will send flow control requests. If it does, the value enabled(3) will be returned. If it does not, it reports disabled(2). If this object is not supported, device reports notSupported(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcPortAutoNegWait 1.3.6.1.4.1.629.200.8.1.1.63
Sets the number of seconds a port should autonegotiate [ANEG] before deciding a link is down. This object is used by the NM when LIN and ANEG are both enabled. If the user knows that a particular end device needs extra time to complete autonegotiation, he should change this object to match the end device's needs. Not supported value: 0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

nbsCmmcPortTemperatureLevel 1.3.6.1.4.1.629.200.8.1.1.64
This object indicates whether this port has a temperature problem. If this port does not support SFF-8472 Digital Diagnostics, this value should be notSupported(1). If Digital Diagnostics indicate temperature is below the low Alarm Threshold, this value should be lowAlarm(2). If Digital Diagnostics indicate temperature is above the low Alarm Threshold but below the low Warning threshold, this value should be lowWarning(3). If Digital Diagnostics indicate this port is within the recommended operating range, value is ok(4). If Digital Diagnostics indicate temperature is higher than the high Warning threshold, but has not crossed the Alarm threshold, this value should be highWarning (5),. If Digital Diagnostics indicate this port has crossed the high Alarm threshold, this value should be highAlarm(6). The related object nbsCmmcPortTemperature indicates what the current temperature is.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), lowAlarm(2), lowWarning(3), ok(4), highWarning(5), highAlarm(6)  

nbsCmmcPortTxPowerLevel 1.3.6.1.4.1.629.200.8.1.1.65
This object indicates whether this port has a problem with its transmitter power. If this port does not support SFF-8472 Digital Diagnostics, this value should be notSupported(1). If Digital Diagnostics indicate TxPower is below the low Alarm Threshold, this value should be lowAlarm(2). If Digital Diagnostics indicate TxPower is above the low Alarm Threshold but below the low Warning threshold, this value should be lowWarning(3). If Digital Diagnostics indicate this port is within the recommended operating range, value is ok(4). If Digital Diagnostics indicate TxPower is higher than the high Warning threshold, but has not crossed the Alarm threshold, this value should be highWarning (5),. If Digital Diagnostics indicate this port has crossed the high Alarm threshold, this value should be highAlarm(6). The related object nbsCmmcPortTxPower indicates what the current TxPower is.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), lowAlarm(2), lowWarning(3), ok(4), highWarning(5), highAlarm(6)  

nbsCmmcPortRxPowerLevel 1.3.6.1.4.1.629.200.8.1.1.66
This object indicates whether this port has a problem with the power of its received signal. If this port does not support SFF-8472 Digital Diagnostics, this value should be notSupported(1). If Digital Diagnostics indicate RxPower is below the low Alarm Threshold, this value should be lowAlarm(2). If Digital Diagnostics indicate RxPower is above the low Alarm Threshold but below the low Warning threshold, this value should be lowWarning(3). If Digital Diagnostics indicate this port is within the recommended operating range, value is ok(4). If Digital Diagnostics indicate RxPower is higher than the high Warning threshold, but has not crossed the Alarm threshold, this value should be highWarning (5),. If Digital Diagnostics indicate this port has crossed the high Alarm threshold, this value should be highAlarm(6). The related object nbsCmmcPortRxPower indicates what the current RxPower is.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), lowAlarm(2), lowWarning(3), ok(4), highWarning(5), highAlarm(6)  

nbsCmmcPortBiasAmpsLevel 1.3.6.1.4.1.629.200.8.1.1.67
This object indicates whether this port has a problem with the electric current going through the port. If this port does not support SFF-8472 Digital Diagnostics, this value should be notSupported(1). If Digital Diagnostics indicate BiasAmps is below the low Alarm Threshold, this value should be lowAlarm(2). If Digital Diagnostics indicate BiasAmps is above the low Alarm Threshold but below the low Warning threshold, this value should be lowWarning(3). If Digital Diagnostics indicate this port is within the recommended operating range, value is ok(4). If Digital Diagnostics indicate BiasAmps is higher than the high Warning threshold, but has not crossed the Alarm threshold, this value should be highWarning (5),. If Digital Diagnostics indicate this port has crossed the high Alarm threshold, this value should be highAlarm(6). The related object nbsCmmcPortBiasAmps indicates what the current amperage is.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), lowAlarm(2), lowWarning(3), ok(4), highWarning(5), highAlarm(6)  

nbsCmmcPortSupplyVoltsLevel 1.3.6.1.4.1.629.200.8.1.1.68
This object indicates whether this port has a problem with the electric voltage across the port. If this port does not support SFF-8472 Digital Diagnostics, this value should be notSupported(1). If Digital Diagnostics indicate SupplyVolts is below the low Alarm Threshold, this value should be lowAlarm(2). If Digital Diagnostics indicate SupplyVolts is above the low Alarm Threshold but below the low Warning threshold, this value should be lowWarning(3). If Digital Diagnostics indicate this port is within the recommended operating range, value is ok(4). If Digital Diagnostics indicate SupplyVolts is higher than the high Warning threshold, but has not crossed the Alarm threshold, this value should be highWarning (5),. If Digital Diagnostics indicate this port has crossed the high Alarm threshold, this value should be highAlarm(6). The related object nbsCmmcPortSupplyVolts indicates what the current supply voltage is.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), lowAlarm(2), lowWarning(3), ok(4), highWarning(5), highAlarm(6)  

nbsCmmcPortAmpGainOper 1.3.6.1.4.1.629.200.8.1.1.69
The current actual operational gain (in milli dB) of an optical amplifier. For nbsCmmcSlotType 503, this object only applies to AGC mode. The reserved value -1 indicates that this object is not supported.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortAmpGainAdmin 1.3.6.1.4.1.629.200.8.1.1.70
The user configured administrative gain (in milli dB) of an optical amplifier. For nbsCmmcSlotType 503, this object only applies to AGC mode. The reserved value -1 indicates that this object is not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortAmpOutputPwrAdmin 1.3.6.1.4.1.629.200.8.1.1.71
The user configured desired output power (in milli dBm) of an optical amplifier. For nbsCmmcSlotType 503, this object only applies to APC mode. Not supported value: 0x80000000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

nbsCmmcPortProtoCapabilities 1.3.6.1.4.1.629.200.8.1.1.72
This bitmask indicates which protocols this port can support. This object is mandatory for all ports in systems where the nbsCmmcSysProtoTable is supported. Bit 0 is reserved. Subsequent bits refer to the nbsCmmcSysProtoTable. Bit 1 corresponds to the first table entry, Bit 2 to the second entry, and so on. A bit is set (1) if that protocol is available for this port, cleared (0) if unavailable. Bit 1 always indicates 'custom' aka 'userDefined' is supported. Bit 2 always indicates 'bypass' aka 'transparent' is supported. OCTET STRING bitmasks count the leftmost bit (MSB) as 0. A zero length OCTET STRING indicates that this object is not supported.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..20)  

nbsCmmcPortProtoAdmin 1.3.6.1.4.1.629.200.8.1.1.73
The nbsCmmcSysProtoIndex of nbsCmmcSysProtoTable corresponding to the administratively desired family and rate of this port's protocol. The value 0 is reserved for 'notSupported' The value 1 is reserved for 'custom' aka 'userDefined'. If a PortNominalBitRate set is received, PortProtoAdmin will automatically change to 1. The value 2 is reserved for 'bypass' aka 'transparent'. Not supported value: 0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortProtoOper 1.3.6.1.4.1.629.200.8.1.1.74
The nbsCmmcSysProtoIndex of nbsCmmcSysProtoTable corresponding to the current operational family and rate of this port's protocol. The value 1 is reserved for 'custom' aka 'userDefined'. If a PortNominalBitRate set is received, PortProtoAdmin will automatically change to 1. The value 2 is reserved for 'bypass' aka 'transparent'. Not supported value: 0
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortPreambleLen 1.3.6.1.4.1.629.200.8.1.1.75
Defines the length of the transmitted ethernet preamble for every frame on this port. The value standard(2) indicates the standard 8 byte ethernet preamble should always be sent. The value variable(3) indicates longer preambles may be sent. The value notSupported(1) indicates preamble length is not configurable or not applicable for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), standard(2), variable(3)  

nbsCmmcPortPreferred 1.3.6.1.4.1.629.200.8.1.1.76
Among a group of ports this object per port says whether this ports is preferred or not. A preferred port in a redundant group (usually a pair of ports) will always be the active link if it has link, regardless of the link state of other ports in its group. Only one port in a redundant group may be preferred. If other ports in the same redundant group are already designated yes(1), the system should automatically set them to no(2). When a port is selected as preferred port, its redundant group is assumed to be in revertive mode. When no port is selected as preferred port, its redundant group is assumed to be in non-revertive (a.k.a. sticky) mode. Once selected, a port's actual active state be read via the SelectLink object. Use caution in designating Preferred ports, because on flaky/intermittent lines, this may result in excessive failovers. If read as notSupported(1), this port either does not belong to a redundant group, or its redundant group is always in non-revertive (a.k.a. sticky) mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), no(2), yes(3)  

nbsCmmcPortCableLen 1.3.6.1.4.1.629.200.8.1.1.77
This object is used to specify the expected maximum cable length for copper DSX ports such as T1, E1, and T3. If a port does not use this feature, this object should be notSupported (1). T1 T-carrier ports should specify a max cable length between 0 to 655 feet using values len133 (2) through len655 (6). T3 T-carrier, E1/E3 E-carrier and STS-1 SONET ports should use either the value shortHaul (7) or longHaul (8).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), len133(2), len266(3), len399(4), len533(5), len655(6), shortHaul(7), longHaul(8)  

nbsCmmcPortRedundantTxMode 1.3.6.1.4.1.629.200.8.1.1.78
This object determines whether or not a redundant port's transmitter should be shut down when that port is on standby. If both redundant ports are connected (via a Y cable) to the same remote port, use the setting oneColonOne (2). This 1:1 configuration will turn off the standby transmitter so it will not interfere with the active port. If each redundant port is connected to its own remote port, use the setting onePlusOne(3). 1+1 leaves both transmitters on, so the remote site can read its link status. Any changes to this object are automatically applied to this port's redundant pair.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), oneColonOne(2), onePlusOne(3)  

nbsCmmcPortTermination 1.3.6.1.4.1.629.200.8.1.1.79
Administrative setting for the line termination impedance of the port. The value disable (2) indicates that the line is to be terminated elsewhere.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disable(2), ohm120(3), ohm100(4), ohm75(5)  

nbsCmmcPortDescription 1.3.6.1.4.1.629.200.8.1.1.80
A functional description of this port. May include port's role in the module, connector type, and other relevant info.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..240)  

nbsCmmcPortTransmitUnmapped 1.3.6.1.4.1.629.200.8.1.1.81
This object is for crossbar products. It allows the user to choose whether this port's transmitter should be enabled or disabled when this port is not mapped to another crossbar port. Setting the value disabled(2) will cause the transmitter to be disabled while the port is unmapped. Setting the value enabled(3) will cause this port to transmit even if unmappped, unless this entire port is disabled via the nbsCmmcPortEnableAdmin object. The agent will report this object as notSupported(1) if the feature is unavailable for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcPortToggleMode 1.3.6.1.4.1.629.200.8.1.1.82
This object allows to the user to toggle the transmitter of this port. The value enabled(3) causes the transmitter to blink on and off at the rate specified in nbsCmmcSlotToggleRate. The value disabled(2) disables the toggle feature. The value notSupported(1) indicates that this port does not support the toggle feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), enabled(3)  

nbsCmmcPortCrossConnect 1.3.6.1.4.1.629.200.8.1.1.83
For ports supporting cross-connect functionality, this object is used to reflect the operating state and clear this port from all cross-connect maps. If the port is not of cross-connect type, the Agent must report notSupported(1). Additionally, if this object reports notSupported(1), any SNMP SET to this object should return SNMP Error 3 (bad value). The Agent should report operating(2) under normal circumstances. If this object reports operating(2), SNMP Managers are allowed to set this object to clearing (3), which instructs the Agent to erase the cross-connect map for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), operating(2), clearing(3)  

nbsCmmcPortZoneIfIndexAdmin 1.3.6.1.4.1.629.200.8.1.1.84
Mib2 ifIndex of desired crossbar partner. Zero (0) indicates this port should be unmapped.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortZoneIfIndexOper 1.3.6.1.4.1.629.200.8.1.1.85
Mib2 ifIndex of actual crossbar partner. Zero (0) indicates this port is currently unmapped.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortEnableOper 1.3.6.1.4.1.629.200.8.1.1.86
Actual current operational status of the port. This object is related to the nbsCmmcPortEnableAdmin object, where users specify the administrative operational status desired. The value notSupported (1) indicates that the port has no ability to disable the transceiver. The value disable (2) indicates that this port's transceiver is not allowing traffic to flow through this port. The value enable (3) indicates that this port's transceiver allows traffic flow.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), disable(2), enable(3)  

nbsCmmcPortMappingType 1.3.6.1.4.1.629.200.8.1.1.87
Administrative crossbar mapping restrictions for this port. Non-crossbar ports must be reported as notSupported(1). If notSupported, any SET attempts will be rejected. Users may not set this object to notSupported(1). Users may mark the port as unavailable(2). If unavailable, the Agent will reject any attempts to map from or to this port. By default, each crossbar port is open(3). Open ports have no mapping restrictions. Ports that are set to source(4) may be used as the input (nbsCmmcPortZoneIfIndexAdmin) port by any other crossbar port. Their own input port may only be mapped to ports whose nbsCmmcPortMappingType is sourceHelper(6). Ports that are set to destination(5) may set their own input (nbsCmmcPortZoneIfIndexAdmin) port to any other crossbar port. They may not be used as the input port for other ports. A sourceHelper(6) port is used to provide whatever sort of link indication is needed by external traffic sources that are connected to a source(4) port. Ports set to interChasLink(7) are physically cabled to another crossbar port in a separate chassis. That connection should be entered by the user in the network topology objects nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort for both those connected ports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), unavailable(2), open(3), source(4), destination(5), sourceHelper(6), interChasLink(7)  

nbsCmmcPortCountersState 1.3.6.1.4.1.629.200.8.1.1.88
This object allows user to reset MAC counters for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), counting(2), clearing(3)  

nbsCmmcPortAmpGainMinimum 1.3.6.1.4.1.629.200.8.1.1.89
This object indicates (in millidecibels) the smallest gain user can set.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortAmpGainMaximum 1.3.6.1.4.1.629.200.8.1.1.90
This object indicates (in millidecibels) the largest gain user can set.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortAmpGainStepSize 1.3.6.1.4.1.629.200.8.1.1.91
Resolution (in millidecibels) of amplifier. Indicates the increment between amplifier gain settings.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortSniffer 1.3.6.1.4.1.629.200.8.1.1.92
Sniffing on or off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), off(2), on(3)  

nbsCmmcPortExternalLink1 1.3.6.1.4.1.629.200.8.1.1.93
Equivalent to the nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort triplet. Set to 0 to indicate this port has no associated intra-node or inter-node endpoint.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndex  

nbsCmmcPortExternalLink2 1.3.6.1.4.1.629.200.8.1.1.94
For y-cable implementations - set by the user to indicate the second intra-node endpoint of a y-cable. Set to 0 to indicate this port has no associated intra-node or inter-node y-cable endpoint.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndex  

nbsCmmcPortNVAreaBanks 1.3.6.1.4.1.629.200.8.1.1.95
The maximum number of executable images that can be stored locally on this module. This number does not count any memory banks that are in a modular subcomponent of this card. Please refer to nbsPartProgNVAreaStart and nbsPartProgNVAreaBanks for that information. Not supported value: 0
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortFirmwareCaps 1.3.6.1.4.1.629.200.8.1.1.96
This bitmask indicates which executable images this module can support. This object is mandatory for all modules. Bit 0 is reserved. Subsequent bits refer to the nbsCmmcSysFirmwareTable. Bit 1 corresponds to the first table entry, Bit 2 to the second entry, and so on. A bit is set (1) if that image is appropriate for this module, cleared (0) if unavailable. OCTET STRING bitmasks count the leftmost bit (MSB) as 0. A zero length OCTET STRING indicates that the nbsCmmcSysFirmwareTable is not supported by this agent.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

nbsCmmcPortFirmwareLoad 1.3.6.1.4.1.629.200.8.1.1.97
This bitmask indicates which executable images this module has stored in its own NV area. This object is mandatory for all modules. OCTET STRING bitmasks count the leftmost bit (MSB) as 0. Bit 0 indicates whether an executable image is loading. Subsequent bits refer to the nbsCmmcSysFirmwareTable. Bit 1 corresponds to the first table entry, Bit 2 to the second entry, and so on. A bit is set (1) if that image is stored on this module, cleared (0) if not. Clearing bits has no effect. To erase an NV area, use the nbsCmmcSysNVAreaTable. Users may transfer a file to an NV area by setting the appropriate file's bit and the loading (MSB) bit to one (1). Adding a file requires that the NM start a file transfer to this module, which is a lengthy operation. If a transfer session is already active (nbsCmmcSlotLoader is non-zero), writes to this object will be rejected. A zero length OCTET STRING indicates that the nbsCmmcSysFirmwareTable is not supported by this agent.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

nbsCmmcPortNVAreaAdmin 1.3.6.1.4.1.629.200.8.1.1.98
A SET on this object will force the corresponding nbsCmmcSysNvAreaStatus to primary, set this module's other memory banks to backup, and immediately load and execute the firmware image contained in the specified memory bank. A GET on this object will indicate the memory bank of this module that is currently designated as primary. Not supported value: -1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortNVAreaOper 1.3.6.1.4.1.629.200.8.1.1.99
The nbsCmmcSysNVAreaBank of nbsCmmcSysNVAreaTable corresponding to the current operationally active firmware image. 0 indicates the current active image is NOT in the NVAreaTable. Not supported value: -1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcPortLoader 1.3.6.1.4.1.629.200.8.1.1.100
The nbsCmmcSysLoaderIndex of nbsCmmcSysLoaderTable corresponding to the current loading session. 0 indicates no loading session is active.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSmtpDomainName 1.3.6.1.4.1.629.200.10.1
This entry contains the device's domain name. For example myDomain.com. It is used to identify the sender's domain.
Status: deprecated Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcSmtpServerAddress 1.3.6.1.4.1.629.200.10.2
Entry containing SMTP server's IP address.
Status: deprecated Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSmtpRcvrLevel 1.3.6.1.4.1.629.200.10.3
Event severity level threshold for this SMTP receiver. If the event severity level is at least nbsCmmcSmtpRcvrLevel. the SNMP agent will generate an e-mail to this SMTP receiver.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSmtpRcvrNum 1.3.6.1.4.1.629.200.10.4
Maximum number of SMTP receivers in nbsCmmcSmtpRcvrTable.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSmtpRcvrTable 1.3.6.1.4.1.629.200.10.5
A list of SMTP receivers entries.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSmtpRcvrEntry

nbsCmmcSmtpRcvrEntry 1.3.6.1.4.1.629.200.10.5.1
Entry containing SMTP information for a particular receiver entry.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSmtpRcvrEntry  

nbsCmmcSmtpRcvrIndex 1.3.6.1.4.1.629.200.10.5.1.1
The Email Recipient Index
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSmtpRcvrEmailAddress 1.3.6.1.4.1.629.200.10.5.1.2
Entry containing SMTP receiver's domain name (email address). The default is the device's domain name, if set.
Status: deprecated Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcSmtpRcvrStatus 1.3.6.1.4.1.629.200.10.5.1.3
To add a new entry to the nbsCmmcSmtpRcvrTable, set this object to valid(2) for an IP address which is not already in the table. To remove an entry from the table, set this object to invalid(1).
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

nbsCmmcSysLogRunningLevel 1.3.6.1.4.1.629.200.11.1
Indicates the level at which the system log message handler saves to a running message log. The level disabled(1) instructs the Agent to log nothing. This level may not be supported in some Agent versions. The level fatal(2) instructs Agent to log only events such as unplanned system shutdowns. The level error(3) includes fatal(2) events and events such as module failures. The level alarm(7) includes fatal(2), error(3), and other events that probably require immediate attention. The level warning(4) includes fatal(2), error(3), alarm(7), as well as events that probably need attention. The level info(5) includes all higher severities, plus events that indicate interesting but not necessarily problematic conditions. The level memo(6) includes all event notifications.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), fatal(2), error(3), warning(4), info(5), memo(6), alarm(7)  

nbsCmmcSysLogNvLevel 1.3.6.1.4.1.629.200.11.2
Indicates the level at which the system log message handler saves in a non-volatile media(NVRAM,FLASH,etc.). For descriptions of each level, please see the DESCRIPTION for nbsCmmcSysLogRunningLevel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), fatal(2), error(3), warning(4), info(5), memo(6), alarm(7)  

nbsCmmcSysLogTrapLevel 1.3.6.1.4.1.629.200.11.3
Indicates the level at which the system log message handler should generate a trap or SNMP notification. For descriptions of each level, please see the DESCRIPTION for nbsCmmcSysLogRunningLevel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), fatal(2), error(3), warning(4), info(5), memo(6), alarm(7)  

nbsCmmcSysLogEmailLevel 1.3.6.1.4.1.629.200.11.4
Indicates the level at which the system log message handler should generate an email message. For descriptions of each level, please see the DESCRIPTION for nbsCmmcSysLogRunningLevel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), fatal(2), error(3), warning(4), deprecated5(5), deprecated6(6), alarm(7), notSupported(8)  

nbsCmmcSysLogMessageTable 1.3.6.1.4.1.629.200.11.5
This table defines a severity level for each type of message/event generated by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysLogMessageEntry

nbsCmmcSysLogMessageEntry 1.3.6.1.4.1.629.200.11.5.1
A system log message control table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysLogMessageEntry  

nbsCmmcSysLogMessageType 1.3.6.1.4.1.629.200.11.5.1.1
System log message type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sysReset(1), snmp(2), physTraps(3), dot1dBridge(4), sysAuthentic(5)  

nbsCmmcSysLogMessageSeverity 1.3.6.1.4.1.629.200.11.5.1.2
System log message severity.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER informational(1), warnings(10), errors(100), emergencies(1000), debugging(10000)  

nbsCmmcSysRunningLogMessageTotal 1.3.6.1.4.1.629.200.11.6
Total number of messages in Running log table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysRunningLogMessageTable 1.3.6.1.4.1.629.200.11.7
A table that describes the logged messages
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysRunningLogMessageEntry

nbsCmmcSysRunningLogMessageEntry 1.3.6.1.4.1.629.200.11.7.1
Contains a description of a particular message entry
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysRunningLogMessageEntry  

nbsCmmcSysRunningLogMessageIndex 1.3.6.1.4.1.629.200.11.7.1.1
The index of the message entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysRunningLogMessageSeverity 1.3.6.1.4.1.629.200.11.7.1.2
The importance of this event.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysRunningLogMessageErrorID 1.3.6.1.4.1.629.200.11.7.1.3
Error code of the message.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysRunningLogMessageSession 1.3.6.1.4.1.629.200.11.7.1.4
Module Id of session causing the event.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysRunningLogMessageTime 1.3.6.1.4.1.629.200.11.7.1.5
Time of occurrence of the event.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysRunningLogMessageModule 1.3.6.1.4.1.629.200.11.7.1.6
The name of the module causing the event.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysRunningLogMessageString 1.3.6.1.4.1.629.200.11.7.1.7
The actual event message.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysNvramLogMessageTotal 1.3.6.1.4.1.629.200.11.8
Total number of messages in Nvram log table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNvramLogMessageTable 1.3.6.1.4.1.629.200.11.9
A table that describes the logged messages
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysNvramLogMessageEntry

nbsCmmcSysNvramLogMessageEntry 1.3.6.1.4.1.629.200.11.9.1
Contains a description of a particular message entry
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysNvramLogMessageEntry  

nbsCmmcSysNvramLogMessageIndex 1.3.6.1.4.1.629.200.11.9.1.1
The index of the message entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNvramLogMessageSeverity 1.3.6.1.4.1.629.200.11.9.1.2
Severity of the error.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysNvramLogMessageErrorID 1.3.6.1.4.1.629.200.11.9.1.3
Error code of the message.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNvramLogMessageSession 1.3.6.1.4.1.629.200.11.9.1.4
Module Id of session causing the error.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNvramLogMessageTime 1.3.6.1.4.1.629.200.11.9.1.5
Value of MIB-II sysUpTime (RFC 1213) at the time the error occurred. Note that sysUpTime resets to zero each time the agent is restarted.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNvramLogMessageModule 1.3.6.1.4.1.629.200.11.9.1.6
The name of the module causing the error.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysNvramLogMessageString 1.3.6.1.4.1.629.200.11.9.1.7
The actual error message.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSysNvramLogMessagePTime 1.3.6.1.4.1.629.200.11.9.1.8
The nbsCmmcSysCurrentTime at the moment this entry was made. This timestamp is derived from the Time Protocol (RFC 868), so it is independent of the system's UpTime. If the agent is unable to obtain the current time from a Time Protocol server, this value is 0. Not supported value: 0
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysNvramLogMessageDateTime 1.3.6.1.4.1.629.200.11.9.1.9
The nbsCmmcSysCurrentDateTime at the moment this entry was made. This timestamp is derived from nbsCmmcSysNvramLogMessagePTime, so it is independent of the system's UpTime.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..24)  

nbsCmmcSysAuditLogTotal 1.3.6.1.4.1.629.200.11.10
The number of entries in the audit log.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysAuditLogTable 1.3.6.1.4.1.629.200.11.11
User activity log.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbsCmmcSysAuditLogEntry

nbsCmmcSysAuditLogEntry 1.3.6.1.4.1.629.200.11.11.1
Contains a description of a particular message entry
Status: current Access: not-accessible
OBJECT-TYPE    
  NbsCmmcSysAuditLogEntry  

nbsCmmcSysAuditLogIndex 1.3.6.1.4.1.629.200.11.11.1.1
The index of the message entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysAuditLogUpTime 1.3.6.1.4.1.629.200.11.11.1.2
Value of MIB-II sysUpTime (RFC 1213) at the time the error occurred. Note that sysUpTime resets to zero each time the agent is restarted.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

nbsCmmcSysAuditLogDateTime 1.3.6.1.4.1.629.200.11.11.1.3
The nbsCmmcSysCurrentDateTime at the moment this entry was made. This timestamp is independent of the system's UpTime.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..24)  

nbsCmmcSysAuditLogString 1.3.6.1.4.1.629.200.11.11.1.4
Log entry. Usually username:login or username:logout
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..250)  

nbsCmmcSysLogRemoteServer 1.3.6.1.4.1.629.200.11.12
The IP address that rsyslog messages should be sent to.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nbsCmmcSysLogRemoteLevel 1.3.6.1.4.1.629.200.11.13
Indicates the level at which the system log message handler sends to remote syslog server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), emerg(2), alert(3), crit(4), error(5), warning(6), notice(7), info(8), debug(9)  

nbsCmmcSysRunningLogMessageClear 1.3.6.1.4.1.629.200.11.14
This object is used to erase all entries from the Agent's internal Running Log. If the Agent does not support this feature, it must return the value notSupported(1), and any SNMP SET to this object should get an SNMP error badValue(3) in response. If this object is supported, the Agent normally should report the value operating(2). If it is actually deleting the log, it may report the value clearing(3). SNMP Managers may set this object to clearing(3), which indicates to the Agent that the log should be emptied.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), operating(2), clearing(3)  

nbsCmmcSysNvramLogMessageClear 1.3.6.1.4.1.629.200.11.15
This object is used to erase all entries from the Agent's internal NVRAM (Persistent Memory) Log. If the Agent does not support this feature, it must return the value notSupported(1), and any SNMP SET to this object should get an SNMP error badValue(3) in response. If this object is supported, the Agent normally should report the value operating(2). If it is actually deleting the log, it may report the value clearing(3). SNMP Managers may set this object to clearing(3), which indicates to the Agent that the log should be emptied.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), operating(2), clearing(3)  

nbsCmmcSysAuditLogClear 1.3.6.1.4.1.629.200.11.16
This object is used to erase all entries from the Agent's internal Audit Log. If the Agent does not support this feature, it must return the value notSupported(1), and any SNMP SET to this object should get an SNMP error badValue(3) in response. If this object is supported, the Agent normally should report the value operating(2). If it is actually deleting the log, it may report the value clearing(3). SNMP Managers may set this object to clearing(3), which indicates to the Agent that the log should be emptied.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), operating(2), clearing(3)  

nbsCmmcSysLogNvSize 1.3.6.1.4.1.629.200.11.17
How large the Nvram log is allowed to be (in kilobytes).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 4..65535  

nbsCmmcTrapLastMessage 1.3.6.1.4.1.629.200.12.1
The last message sent by the system
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcTrapPowerSupplyId 1.3.6.1.4.1.629.200.12.2
ID of the power supply
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER  

nbsCmmcTrapFanId 1.3.6.1.4.1.629.200.12.3
ID of the fan
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER  

nbsCmmcTrapPortIndex 1.3.6.1.4.1.629.200.12.4
Index of the Port
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER  

nbsCmmcTrapPortName 1.3.6.1.4.1.629.200.12.5
Name of the Port
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcTrapShutdownReason 1.3.6.1.4.1.629.200.12.6
The reason for the last system shutdown
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcTrapErrorInfo 1.3.6.1.4.1.629.200.12.7
Brief explanation of the cause or nature of errors that triggered an nbsCmmcTrapPortErrorsDetected trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..255)  

nbsCmmcSlotModelLocked 1.3.6.1.4.1.629.200.12.10
The model of the slot's saved configuration.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcSlotModelInserted 1.3.6.1.4.1.629.200.12.11
The model of the newly inserted module.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..50)  

nbsCmmcTrapGenericTrap 1.3.6.1.4.1.629.200.13.0.1
The last message sent by the system.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSpecificTrap 1.3.6.1.4.1.629.200.13.0.2
********* DEPRECATED ********** As of Agent version 4.14, this trap will not be sent.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapDeviceRebooted 1.3.6.1.4.1.629.200.13.0.3
Sent after device boots up. The cause of the last shutdown is indicated in nbsCmmcTrapShutdownReason. This Notification should be of Severity FATAL.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapDeviceOnline 1.3.6.1.4.1.629.200.13.0.4
Sent when device detects restoration of network communications. ChassisIndex and SlotIndex indicate the location of the NM issuing the trap This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapDeviceShuttingDown 1.3.6.1.4.1.629.200.13.0.5
Sent just before device shuts itself down. Reason for shutdown is indicated in nbsCmmcTrapShutdownReason. This Notification should be of Severity FATAL.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPowerSupplyFailure 1.3.6.1.4.1.629.200.13.0.6
Unique trap for power supply failure events. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPowerSupplyRestored 1.3.6.1.4.1.629.200.13.0.7
Sent when power supply starts working again. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapFanFailure 1.3.6.1.4.1.629.200.13.0.8
Unique trap for fan failure events. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapFanRestored 1.3.6.1.4.1.629.200.13.0.9
Sent when fan starts working again. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapChassisTooHot 1.3.6.1.4.1.629.200.13.0.10
Sent when temperature rises above hottest permissible temperature. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapChassisTooCold 1.3.6.1.4.1.629.200.13.0.11
Sent when temperature falls under coldest permissible temperature. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapChassisTempOk 1.3.6.1.4.1.629.200.13.0.12
Sent when temperature returns to permissible range. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSlotModuleIn 1.3.6.1.4.1.629.200.13.0.13
Sent when card is physically inserted. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSlotModuleOut 1.3.6.1.4.1.629.200.13.0.14
Sent when card is physically removed. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortEnabled 1.3.6.1.4.1.629.200.13.0.15
Sent after nbsCmmcPortEnableOper changes to enable(3). This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortDisabled 1.3.6.1.4.1.629.200.13.0.16
Sent after nbsCmmcPortEnableOper changes to disable(2). This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortLinkUp 1.3.6.1.4.1.629.200.13.0.17
Sent when nbsCmmcPortLink transitions from noSignal(2) to a connected state. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortLinkDown 1.3.6.1.4.1.629.200.13.0.18
Sent when nbsCmmcPortLink transitions from a connected state to noSignal(2). This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortLINOn 1.3.6.1.4.1.629.200.13.0.19
Sent when Link Integrity Notification is turned on. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortLINOff 1.3.6.1.4.1.629.200.13.0.20
Sent when Link Integrity Notification is turned off. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortLoopbackOn 1.3.6.1.4.1.629.200.13.0.21
Sent when Port is set to a Loopback state. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortLoopbackOff 1.3.6.1.4.1.629.200.13.0.22
Sent when Port returns from a Loopback state. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortMaximumExceeded 1.3.6.1.4.1.629.200.13.0.23
Sent when PortValue exceeds PortThreshold. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortRemoved 1.3.6.1.4.1.629.200.13.0.24
Sent when a hot-swappable port is removed. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortInserted 1.3.6.1.4.1.629.200.13.0.25
Sent when a hot-swappable port is inserted. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortTempTooLow 1.3.6.1.4.1.629.200.13.0.26
Sent when transmitter temperature is too cold. For SFF Digital Diagnostics, this corresponds to the low temperature alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortTempTooHigh 1.3.6.1.4.1.629.200.13.0.27
Sent when transmitter temperature is too hot. For SFF Digital Diagnostics, this corresponds to the high temperature alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortRxPowerTooLow 1.3.6.1.4.1.629.200.13.0.28
Sent when received signal is too weak. For SFF Digital Diagnostics, this corresponds to the low RX power alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortRxPowerTooHigh 1.3.6.1.4.1.629.200.13.0.29
Sent when received signal is too powerful. For SFF Digital Diagnostics, this corresponds to the high RX power alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortTxPowerTooLow 1.3.6.1.4.1.629.200.13.0.30
Sent when transmitter power is too weak. For SFF Digital Diagnostics, this corresponds to the low TX power alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortTxPowerTooHigh 1.3.6.1.4.1.629.200.13.0.31
Sent when transmitter power is too strong. For SFF Digital Diagnostics, this corresponds to the high TX power alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortAmpsTooLow 1.3.6.1.4.1.629.200.13.0.32
Sent when bias current is too small. For SFF Digital Diagnostics, this corresponds to the low bias current alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortAmpsTooHigh 1.3.6.1.4.1.629.200.13.0.33
Sent when bias current is too large. For SFF Digital Diagnostics, this corresponds to the high bias current alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortVoltsTooLow 1.3.6.1.4.1.629.200.13.0.34
Sent when transceiver supply voltage is too low. For SFF Digital Diagnostics, this corresponds to the low supply voltage alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortVoltsTooHigh 1.3.6.1.4.1.629.200.13.0.35
Sent when transceiver supply voltage is too high. For SFF Digital Diagnostics, this corresponds to the high supply voltage alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSwitchover 1.3.6.1.4.1.629.200.13.0.36
Sent when a self-healing (redundant ports) card switches traffic from an active port to a standby port. This Notification should be of Severity WARNING. The VARIABLE TrapLastMessage should specify the cause of the switchover, the PortName of the new Active port, and the PortName of the new Standby (formerely Active) port. The ChassisIndex and SlotIndex indicate the card that performed the switchover. The first PortIndex is the new Active port. The last PortIndex is the new Standby port. This trap should be accompanied by link up/down traps.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSlotShuttingDown 1.3.6.1.4.1.629.200.13.0.37
Sent when the slot/card is shutting down. This Notification should be of Severity WARNING if the shutdown is deliberate, or ERROR if shutdown because of module failure, i.e. last gasp. The VARIABLE nbsCmmcTrapShutdownReason should specify the reason the card is shutting down. To enable/disable this notification, use the object nbsCmmcChassisEnableModuleSpecificTraps.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortCrcError 1.3.6.1.4.1.629.200.13.0.38
Sent when CRC Error is received on this port. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapCpeInManagedChassis 1.3.6.1.4.1.629.200.13.0.39
Sent when a module configured for customer premises is detected in a managed (central office) chassis. This Notification should be of Severity WARNING. To enable/disable this notification, use the object nbsCmmcChassisEnableModuleSpecificTraps.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapCoWithoutCpe 1.3.6.1.4.1.629.200.13.0.40
Sent when a central office module has no link to a CPE module. This Notification should be of Severity WARNING. To enable/disable this notification, use the object nbsCmmcChassisEnableModuleSpecificTraps.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapCoTakesControl 1.3.6.1.4.1.629.200.13.0.41
Sent when a central office module begins active management of a dual-homed CPE module. This Notification should be of Severity WARNING. To enable/disable this notification, use the object nbsCmmcChassisEnableModuleSpecificTraps.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapCoYieldsControl 1.3.6.1.4.1.629.200.13.0.42
Sent when a central office module ceases active management of a dual-homed CPE module. This Notification should be of Severity WARNING. To enable/disable this notification, use the object nbsCmmcChassisEnableModuleSpecificTraps.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapCoLinkedToCo 1.3.6.1.4.1.629.200.13.0.43
Sent when one central office module is connected to another central office module. This Notification should be of Severity ERROR. To enable/disable this notification, use the object nbsCmmcChassisEnableModuleSpecificTraps.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapCpeFound 1.3.6.1.4.1.629.200.13.0.44
Sent when a remote CPE module is detected. This Notification should be of Severity WARNING. To enable/disable this notification, use the object nbsCmmcChassisEnableModuleSpecificTraps.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortReflectionDetected 1.3.6.1.4.1.629.200.13.0.45
Sent when SingleFiber port detects its own signal reflecting back on itself. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortReflectionCeased 1.3.6.1.4.1.629.200.13.0.46
Sent when SingleFiber port no longer detects its own signal returning. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortTempOk 1.3.6.1.4.1.629.200.13.0.47
Sent when transmitter temperature returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity of the nbsCmmcTrapPortTempTooLow or nbsCmmcTrapPortTempTooHigh NOTIFICATION that this overrides.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortRxPowerOk 1.3.6.1.4.1.629.200.13.0.48
Sent when received signal returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity of the nbsCmmcTrapPortRxPowerTooLow or nbsCmmcTrapPortRxPowerTooHigh NOTIFICATION that this overrides.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortTxPowerOk 1.3.6.1.4.1.629.200.13.0.49
Sent when transmitter power returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity of the nbsCmmcTrapPortTxPowerTooLow or nbsCmmcTrapPortTxPowerTooHigh NOTIFICATION that this overrides.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortAmpsOk 1.3.6.1.4.1.629.200.13.0.50
Sent when bias current returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity of the nbsCmmcTrapPortAmpsTooLow or bsCmmcTrapPortAmpsTooHigh NOTIFICATION that this overrides.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortVoltsOk 1.3.6.1.4.1.629.200.13.0.51
Sent when transceiver supply voltage returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity of the nbsCmmcTrapPortVoltsTooLow or nbsCmmcTrapPortVoltsTooHigh NOTIFICATION that this overrides.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSlotTempTooLow 1.3.6.1.4.1.629.200.13.0.52
Sent when slot temperature is too cold. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSlotTempTooHigh 1.3.6.1.4.1.629.200.13.0.53
Sent when slot temperature is too hot. temperature alarm. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSlotTempOk 1.3.6.1.4.1.629.200.13.0.54
Sent when slot temperature returns to normal. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortErrorsDetected 1.3.6.1.4.1.629.200.13.0.55
Sent when nbsCmmcPortErrorActivity changes to on(3). This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPortErrorsStopped 1.3.6.1.4.1.629.200.13.0.56
Sent when nbsCmmcPortErrorActivity changes to off(2). This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapChassisInsufficientPower 1.3.6.1.4.1.629.200.13.0.57
Sent when power on chassis changed to insufficient. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapChassisSufficientPower 1.3.6.1.4.1.629.200.13.0.58
Sent when power on chassis changed to sufficient. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSlotModuleLocked 1.3.6.1.4.1.629.200.13.0.59
Sent when nbsCmmcSysLockTypes is enabled(3) and a card incompatible with a slot's locked configuration is inserted. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapSelectLinkChanged 1.3.6.1.4.1.629.200.13.0.60
Sent when a redundant port in a self-healing card switches between active and standby. The last varbind, nbsCmmcPortSelectLink, indicates this port's new state. This notification should come in a pair -- one trap for the new active port, another for the new standby port. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPowerSupplyRemoved 1.3.6.1.4.1.629.200.13.0.66
Event triggered by physical removal of a power supply. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapPowerSupplyInserted 1.3.6.1.4.1.629.200.13.0.67
Triggered by physical insertion of a power supply. This Notification should be of Severity ERROR.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapFanRemoved 1.3.6.1.4.1.629.200.13.0.68
Triggered by physical removal of fan assembly. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapFanInserted 1.3.6.1.4.1.629.200.13.0.69
Triggered by physical insertion of fan assembly. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

nbsCmmcTrapModuleStatusChanged 1.3.6.1.4.1.629.200.13.0.70
Triggered when nbsCmmcSlotModuleStatus changes. If a module is unplugged and nbsCmmcSlotModuleStatus transitions directly to empty(2), a trap will not be generated. This Notification should be of Severity WARNING.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE