MULTIPLE-BRIDGE-MIB
File:
MULTIPLE-BRIDGE-MIB.mib (9792 bytes)
Imported modules
Imported symbols
Defined Types
AtiPortentry |
|
SEQUENCE |
|
|
|
|
atiPort |
INTEGER |
|
|
atiPortStatus |
INTEGER |
|
|
atiPortDuplexStatus |
INTEGER |
|
|
atiPortForwardedFrames |
Counter |
|
|
atiPortRcvdLocalFrames |
Counter |
|
Defined Values
ati |
1.3.6.1.4.1.207 |
OBJECT IDENTIFIER |
|
|
|
mibobjs |
1.3.6.1.4.1.207.8 |
OBJECT IDENTIFIER |
|
|
|
atiSwitch |
1.3.6.1.4.1.207.8.3.3 |
OBJECT IDENTIFIER |
|
|
|
atiSysPowerupCount |
1.3.6.1.4.1.207.8.3.1.4 |
Powerup Count. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
atiSysBrcastCutoffRate |
1.3.6.1.4.1.207.8.3.1.5 |
Broadcast Cutoff Rate. (0..100000) |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
atiPortTable |
1.3.6.1.4.1.207.8.3.2 |
The port setup table. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AtiPortentry |
|
atiPortEntry |
1.3.6.1.4.1.207.8.3.2.1 |
The port setup entry. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AtiPortentry |
|
|
atiPort |
1.3.6.1.4.1.207.8.3.2.1.1 |
A number from 1 to number of ports on the switch. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
atiPortStatus |
1.3.6.1.4.1.207.8.3.2.1.2 |
Port status. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
up(1), down(2) |
|
atiPortDuplexStatus |
1.3.6.1.4.1.207.8.3.2.1.3 |
Port duplex status. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
half(1), full(2) |
|
atiPortForwardedFrames |
1.3.6.1.4.1.207.8.3.2.1.4 |
Number of frames received on this port and forwarded to another port on the system module for processing. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter |
|
|
atiPortRcvdLocalFrames |
1.3.6.1.4.1.207.8.3.2.1.5 |
Number of frames received where the destination is on this port. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter |
|
|
atiSwitchIPAddress |
1.3.6.1.4.1.207.8.3.3.1 |
Since bridges can now be accessed without an IP address,
there needs to be a way to find out there addresses. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
NetworkAddress |
|
|
atiActiveAgingTime |
1.3.6.1.4.1.207.8.3.3.3 |
Active Aging Time. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
atiPurgeAgingTime |
1.3.6.1.4.1.207.8.3.3.4 |
Purge Aging Time. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
atiSwitchSTPStatus |
1.3.6.1.4.1.207.8.3.3.5 |
The switch's Spanning Tree status, enter ON or OFF. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
on(1), off(2) |
|
atiSwitchPortMirroring |
1.3.6.1.4.1.207.8.3.3.7 |
The switch's Port Mirroring status, enter ENABLE or DISABLE. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
atiSwitchMirroredPort |
1.3.6.1.4.1.207.8.3.3.8 |
The Port to be mirrored. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|