MPLS-ID-STD-MIB
File:
MPLS-ID-STD-MIB.mib (7754 bytes)
Imported modules
Imported symbols
Defined Values
| mplsIdStdMIB |
1.3.6.1.2.1.10.166.18 |
| This MIB module contains identifier object definitions for
MPLS Traffic Engineering in transport networks.
Copyright (c) 2015 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject to
the license terms contained in, the Simplified BSD License set
forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info). |
| MODULE-IDENTITY |
|
|
|
| mplsIdGlobalId |
1.3.6.1.2.1.10.166.18.1.1 |
| This object allows the operator or service provider to
assign a unique operator identifier, also called the MPLS-TP
Global_ID.
If this value is used in mplsTunnelExtNodeConfigGlobalId
for mapping Global_ID::Node_ID with the local identifier,
then this object value MUST NOT be changed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
MplsGlobalId |
|
|
| mplsIdNodeId |
1.3.6.1.2.1.10.166.18.1.2 |
| This object allows the operator or service provider to
assign a unique MPLS-TP Node_ID. The Node_ID is assigned
within the scope of the Global_ID/ICC_Operator_ID.
If this value is used in mplsTunnelExtNodeConfigNodeId
for mapping Global_ID::Node_ID with the local identifier,
then this object value SHOULD NOT be changed.
If this value is used in mplsTunnelExtNodeConfigNodeId
for mapping ICC_Operator_ID::Node_ID with the local
identifier, then this object value MUST NOT be changed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
MplsNodeId |
|
|
| mplsIdCc |
1.3.6.1.2.1.10.166.18.1.3 |
| This object allows the operator or service provider to
assign a Country Code (CC) to the node. Global
uniqueness of ICC is assured by concatenating the ICC
with a Country Code (CC).
If this value is used in mplsTunnelExtNodeConfigCcId
for mapping ICC_Operator_ID::Node_ID with the local
identifier, then this object value MUST NOT be changed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
MplsCcId |
|
|
| mplsIdIcc |
1.3.6.1.2.1.10.166.18.1.4 |
| This object allows the operator or service provider to
assign a unique MPLS-TP ITU-T Carrier Code (ICC) to
the node. Together, the CC and the ICC form
the ICC_Operator_ID as CC::ICC.
If this value is used in mplsTunnelExtNodeConfigIccId
for mapping ICC_Operator_ID::Node_ID with the local
identifier, then this object value MUST NOT be changed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
MplsIccId |
|
|
| mplsIdModuleFullCompliance |
1.3.6.1.2.1.10.166.18.2.1.1 |
| Compliance statement for agents that provide full
support of the MPLS-ID-STD-MIB module. |
| Status: current |
Access: read-write |
| MODULE-COMPLIANCE |
|
|
|
| mplsIdModuleReadOnlyCompliance |
1.3.6.1.2.1.10.166.18.2.1.2 |
| Compliance statement for agents that only provide
read-only support for the MPLS-ID-STD-MIB module. |
| Status: current |
Access: read-only |
| MODULE-COMPLIANCE |
|
|
|
| mplsIdIpOperatorGroup |
1.3.6.1.2.1.10.166.18.2.2.1 |
| The objects in this group are optional for an
ICC-based node. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mplsIdIccOperatorGroup |
1.3.6.1.2.1.10.166.18.2.2.2 |
| The objects in this group are optional for an
IP-based node. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|