MOXA-EDSG508E-MIB

File: MOXA-EDSG508E-MIB.mib (192668 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC

Imported symbols

enterprises MODULE-IDENTITY NOTIFICATION-TYPE
IpAddress OBJECT-TYPE DateAndTime
TEXTUAL-CONVENTION MacAddress DisplayString

Defined Types

PortList  
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION    
  OCTET STRING  

PortEntry  
SEQUENCE    
  portIndex INTEGER
  portDesc DisplayString
  portEnable INTEGER
  portSpeed INTEGER
  portMDI INTEGER
  portFDXFlowCtrl INTEGER
  portName DisplayString
  portSubdesc DisplayString

MonitorPortEntry  
SEQUENCE    
  monitorLinkStatus INTEGER
  monitorSpeed INTEGER
  monitorAutoMDI INTEGER
  monitorTraffic INTEGER
  monitorFDXFlowCtrl INTEGER
  monitorTxTraffic INTEGER
  monitorRxTraffic INTEGER

MonitorDiEntry  
SEQUENCE    
  diIndex INTEGER
  diInputStatus INTEGER

MonitorFiberCheckEntry  
SEQUENCE    
  fiberPort DisplayString
  fiberModelName DisplayString
  fiberWaveLength DisplayString
  fiberVoltage DisplayString
  fiberTemperature DisplayString
  fiberTempWarn DisplayString
  fiberTxPower DisplayString
  fiberTxPowerWarn DisplayString
  fiberRxPower DisplayString
  fiberRxPowerWarn DisplayString
  fiberSN DisplayString

SetDevIpEntry  
SEQUENCE    
  setDevIpIndex INTEGER
  setDevIpCurrentIpofDevice DisplayString
  setDevIpPresentBy INTEGER
  setDevIpDedicatedIp IpAddress

TrunkSettingEntry  
SEQUENCE    
  trunkSettingIndex INTEGER
  trunkType INTEGER
  trunkMemberPorts PortList

TrunkEntry  
SEQUENCE    
  trunkIndex INTEGER
  trunkPort INTEGER
  trunkStatus INTEGER

TurboRingPortEntry  
SEQUENCE    
  turboRingPortIndex INTEGER
  turboRingPortStatus INTEGER
  turboRingPortDesignatedBridge OCTET STRING
  turboRingPortDesignatedPort INTEGER

SpanningTreeEntry  
SEQUENCE    
  spanningTreeIndex INTEGER
  enableSpanningTree INTEGER
  spanningTreePortPriority INTEGER
  spanningTreePortCost INTEGER
  spanningTreePortStatus INTEGER
  spanningTreePortEdge INTEGER

RelayWarningEntry  
SEQUENCE    
  relayAlarmIndex INTEGER
  relayWarningRelayContact INTEGER
  overrideRelayWarningSetting INTEGER
  relayWarningPower1Off INTEGER
  relayWarningPower1OffStatus INTEGER
  relayWarningPower2Off INTEGER
  relayWarningPower2OffStatus INTEGER
  relayWarningTurboRingBreak INTEGER
  relayWarningTurboRingBreakStatus INTEGER

PortRelayWarningEntry  
SEQUENCE    
  relayWarningLinkChanged INTEGER
  relayWarningLinkChangedStatus INTEGER
  relayWarningTrafficOverload INTEGER
  relayWarningTrafficOverloadStatus INTEGER
  relayWarningRxTrafficThreshold INTEGER
  relayWarningTrafficDuration INTEGER

DiRelayWarningEntry  
SEQUENCE    
  relayWarningDiInputChanged INTEGER
  relayWarningDiInputChangedStatus INTEGER

QosPortEntry  
SEQUENCE    
  dscpInspection INTEGER
  cosInspection INTEGER
  portPriority INTEGER

PriorityMappingEntry  
SEQUENCE    
  priorityTag INTEGER
  priorityMappedQueue INTEGER

DscpMappingEntry  
SEQUENCE    
  dscpClass INTEGER
  dscpMappedPriority INTEGER

VlanPortSettingEntry  
SEQUENCE    
  portVlanType INTEGER
  portDefaultVid INTEGER
  portFixedVid DisplayString
  portFixedVidUntag DisplayString
  portForbiddenVid DisplayString

VlanEntry  
SEQUENCE    
  vlanId INTEGER
  joinedAccessPorts PortList
  joinedTrunkPorts PortList
  joinedHybridPorts PortList
  vlanName DisplayString

PortbaseVlanSettingEntry  
SEQUENCE    
  portbaseVlanSettingIndex INTEGER
  portbaseVlanMemberPorts PortList

IgmpSnoopingSettingEntry  
SEQUENCE    
  enableIgmpSnooping INTEGER
  enableQuerier INTEGER
  fixedMulticastQuerierPorts PortList
  learnedMulticastQuerierPorts PortList

StaticMulticastEntry  
SEQUENCE    
  staticMulticastAddress MacAddress
  staticMulticastPorts PortList
  staticMulticastStatus INTEGER

GmrpSettingEntry  
SEQUENCE    
  enableGMRP INTEGER

GmrpEntry  
SEQUENCE    
  gmrpMulticastGroup MacAddress
  gmrpFixedPorts PortList
  gmrpLearnedPorts PortList

DroppacketModeRateLimitingIngressEntry  
SEQUENCE    
  ingressLimitRate INTEGER

PortDisableModeEntry  
SEQUENCE    
  ingressLimit INTEGER

Dot1xSettingEntry  
SEQUENCE    
  enableDot1X INTEGER

Dot1xReauthEntry  
SEQUENCE    
  dot1xReauthPortIndex INTEGER
  dot1xReauth INTEGER

PortAccessControlEntry  
SEQUENCE    
  portAccessControlAddress MacAddress
  portAccessControlPortNo INTEGER
  portAccessControlAccessStatus INTEGER
  portAccessControlStatus INTEGER
  portAccessControlVid INTEGER

PortSecurityModeEntry  
SEQUENCE    
  portSecurityModePort INTEGER
  portSecurityModeSelect INTEGER
  portSecurityModeLimit INTEGER
  portSecurityModeViolationPortDisable INTEGER
  portSecurityModeStatus INTEGER

MABSettingEntry  
SEQUENCE    
  enableMAB INTEGER

AccessibleIpEntry  
SEQUENCE    
  accessibleIpAddress IpAddress
  accessibleIpNetMask IpAddress
  accessibleIpStatus INTEGER

NtpPeerEntry  
SEQUENCE    
  ntpPeerIndex INTEGER
  ntpPeerAddress DisplayString
  ntpPeerAuthenticate INTEGER
  ntpPeerAuthenticateKeyid INTEGER

NtpAuthenticateKeyEntry  
SEQUENCE    
  ntpAuthenticateKeyIndex INTEGER
  ntpAuthenticateKeyID INTEGER
  ntpAuthenticateKeyString DisplayString
  ntpAuthenticateKeyTrusted INTEGER

DhcpFunctionEntry  
SEQUENCE    
  dhcpPortIndex INTEGER
  circuitID DisplayString
  option82Enable INTEGER

PtpPortEntry  
SEQUENCE    
  ptpPortIndex INTEGER
  ptpPortEnable INTEGER
  ptpPortStatus INTEGER

EventlogEntry  
SEQUENCE    
  eventlogIndex INTEGER
  eventlogBootup INTEGER
  eventlogDate DisplayString
  eventlogTime DisplayString
  eventlogUptime DisplayString
  eventlogEvent DisplayString

AccessControlEntry  
SEQUENCE    
  aclRuleIndex INTEGER
  listID INTEGER
  filterType INTEGER
  actionFlag INTEGER
  srcMacAddr MacAddress
  srcMacMask MacAddress
  dstMacAddr MacAddress
  dstMacMask MacAddress
  etherType INTEGER
  vlanID INTEGER
  srcIpAddr IpAddress
  srcNetmask IpAddress
  dstIpAddr IpAddress
  dstNetmask IpAddress
  protocolCode INTEGER
  srcsocketPort INTEGER
  dstsocketPort INTEGER
  aclStatus INTEGER

AclAttachmentEntry  
SEQUENCE    
  aclID INTEGER
  ingressPort PortList
  aclListName DisplayString

SystemEventSettingsEntry  
SEQUENCE    
  systemEventIndex INTEGER
  systemEventActive INTEGER
  systemEventName DisplayString
  systemEventSupport INTEGER
  systemEventModuleEnable INTEGER
  systemEventSeverity INTEGER

PortEventSettingsEntry  
SEQUENCE    
  portEventIndex INTEGER
  portEventLabel DisplayString
  portEventActive INTEGER
  portEventEnable INTEGER
  portEventTrafficThreshold INTEGER
  portEventTrafficDuration INTEGER
  portEventModuleEnable INTEGER
  portEventSeverity INTEGER

Defined Values

moxa 1.3.6.1.4.1.8691
OBJECT IDENTIFIER    

industrialEthernet 1.3.6.1.4.1.8691.7
OBJECT IDENTIFIER    

edsg508e 1.3.6.1.4.1.8691.7.69
The MIB module for Moxa EDS-G508E series specific information.
MODULE-IDENTITY    

swMgmt 1.3.6.1.4.1.8691.7.69.1
OBJECT IDENTIFIER    

swTraps 1.3.6.1.4.1.8691.7.69.2
OBJECT IDENTIFIER    

numberOfPorts 1.3.6.1.4.1.8691.7.69.1.1
Total Ports.
OBJECT-TYPE    
  INTEGER  

switchModel 1.3.6.1.4.1.8691.7.69.1.2
The switch model.
OBJECT-TYPE    
  DisplayString  

firmwareVersion 1.3.6.1.4.1.8691.7.69.1.4
The firmware version.
OBJECT-TYPE    
  DisplayString  

enableWebConfig 1.3.6.1.4.1.8691.7.69.1.5
This enable the Web. configuration function.
OBJECT-TYPE    
  INTEGER disable(0), httpOrHttps(1), httpsOnly(2)  

consoleLoginMode 1.3.6.1.4.1.8691.7.69.1.51
This option can change console login mode.
OBJECT-TYPE    
  INTEGER menu(0), cli(1)  

enableTelnetConsole 1.3.6.1.4.1.8691.7.69.1.6
This enable telnet console.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lineSwapRecovery 1.3.6.1.4.1.8691.7.69.1.7
This enable line-swap-fast-recovery function.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

agingTime 1.3.6.1.4.1.8691.7.69.1.44
Web Timeout
OBJECT-TYPE    
  INTEGER  

supportIfXTable 1.3.6.1.4.1.8691.7.69.1.69
Support 64 bit Counter (ifXTable).
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

networkSetting 1.3.6.1.4.1.8691.7.69.1.8
OBJECT IDENTIFIER    

switchIpAddr 1.3.6.1.4.1.8691.7.69.1.8.1
The IP Address of this switch.
OBJECT-TYPE    
  IpAddress  

switchIpMask 1.3.6.1.4.1.8691.7.69.1.8.2
The netmask of this switch.
OBJECT-TYPE    
  IpAddress  

defaultGateway 1.3.6.1.4.1.8691.7.69.1.8.3
The default gateway of this switch.
OBJECT-TYPE    
  IpAddress  

enableAutoIpConfig 1.3.6.1.4.1.8691.7.69.1.8.4
This enable the automatic IP address configuration function.
OBJECT-TYPE    
  INTEGER disable(0), enableDHCP(1), enableBOOTP(2)  

dnsServer1IpAddr 1.3.6.1.4.1.8691.7.69.1.8.5
The first DNS server's IP address
OBJECT-TYPE    
  IpAddress  

snmpTrapCommunity 1.3.6.1.4.1.8691.7.69.1.8.6
The SNMP trap community name
OBJECT-TYPE    
  DisplayString  

trapServerAddr 1.3.6.1.4.1.8691.7.69.1.8.7
The IP address/Domain name of SNMP trap server
OBJECT-TYPE    
  DisplayString  

dnsServer2IpAddr 1.3.6.1.4.1.8691.7.69.1.8.8
The second DNS server's IP address
OBJECT-TYPE    
  IpAddress  

snmpReadCommunity 1.3.6.1.4.1.8691.7.69.1.8.9
The SNMP read community name
OBJECT-TYPE    
  DisplayString  

snmpTrap2Community 1.3.6.1.4.1.8691.7.69.1.8.11
The Second SNMP trap community name
OBJECT-TYPE    
  DisplayString  

trap2ServerAddr 1.3.6.1.4.1.8691.7.69.1.8.12
The IP address/Domain name of Second SNMP trap server
OBJECT-TYPE    
  DisplayString  

snmpInformEnable 1.3.6.1.4.1.8691.7.69.1.8.13
This enable the snmpInform function.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

snmpInformRetries 1.3.6.1.4.1.8691.7.69.1.8.14
The snmp inform retry times of SNMP trap server
OBJECT-TYPE    
  INTEGER 1..99  

snmpInformTimeout 1.3.6.1.4.1.8691.7.69.1.8.15
The snmp inform interval of SNMP trap server
OBJECT-TYPE    
  INTEGER 1..300  

dhcpRetryPeriods 1.3.6.1.4.1.8691.7.69.1.8.16
The DHCP retry periods.
OBJECT-TYPE    
  INTEGER  

dhcpRetryTimes 1.3.6.1.4.1.8691.7.69.1.8.17
The dhcp retry times.
OBJECT-TYPE    
  INTEGER  

trapVersion 1.3.6.1.4.1.8691.7.69.1.8.18
Version of SNMP trap
OBJECT-TYPE    
  INTEGER snmpv1-Trap(0), snmpv2-Notification(1), snmpv2-Inform(2), snmpv3-Trap(3), snmpv3-Inform(4)  

snmpVersion 1.3.6.1.4.1.8691.7.69.1.8.21
Version of SNMP
OBJECT-TYPE    
  INTEGER snmpv1-v2c-v3(1), snmpv1-v2c(2), snmpv3(3)  

snmpAdminSecurityLevel 1.3.6.1.4.1.8691.7.69.1.8.22
Admin security level
OBJECT-TYPE    
  INTEGER noAuthNoPriv(1), authNoPriv(2), authPriv(3)  

snmpUserSecurityLevel 1.3.6.1.4.1.8691.7.69.1.8.23
User security level
OBJECT-TYPE    
  INTEGER noAuthNoPriv(1), authNoPriv(2), authPriv(3)  

portSetting 1.3.6.1.4.1.8691.7.69.1.9
OBJECT IDENTIFIER    

portTable 1.3.6.1.4.1.8691.7.69.1.9.1
The port table.
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 1.3.6.1.4.1.8691.7.69.1.9.1.1
The port entry.
OBJECT-TYPE    
  PortEntry  

portIndex 1.3.6.1.4.1.8691.7.69.1.9.1.1.1
The port index.
OBJECT-TYPE    
  INTEGER  

portDesc 1.3.6.1.4.1.8691.7.69.1.9.1.1.2
The port description
OBJECT-TYPE    
  DisplayString  

portEnable 1.3.6.1.4.1.8691.7.69.1.9.1.1.3
This enable the port.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

portSpeed 1.3.6.1.4.1.8691.7.69.1.9.1.1.4
The port speed and duplex.
OBJECT-TYPE    
  INTEGER auto(0), speed100M-Full(1), speed100M-Half(2), speed10M-Full(3), speed10M-Half(4), speed1000M-Full(5)  

portMDI 1.3.6.1.4.1.8691.7.69.1.9.1.1.5
The port MDI/MDIX.
OBJECT-TYPE    
  INTEGER na(0), auto(1), mdi(2), mdiX(3)  

portFDXFlowCtrl 1.3.6.1.4.1.8691.7.69.1.9.1.1.6
The port FDX Flow Control
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

portName 1.3.6.1.4.1.8691.7.69.1.9.1.1.7
The port Name
OBJECT-TYPE    
  DisplayString  

portSubdesc 1.3.6.1.4.1.8691.7.69.1.9.1.1.8
The port second description
OBJECT-TYPE    
  DisplayString  

monitor 1.3.6.1.4.1.8691.7.69.1.10
OBJECT IDENTIFIER    

power1InputStatus 1.3.6.1.4.1.8691.7.69.1.10.1
The status of the first power input.
OBJECT-TYPE    
  INTEGER not-present(0), present(1)  

power2InputStatus 1.3.6.1.4.1.8691.7.69.1.10.2
The status of the second power input.
OBJECT-TYPE    
  INTEGER not-present(0), present(1)  

monitorPortTable 1.3.6.1.4.1.8691.7.69.1.10.3
The port table of monitor function.
OBJECT-TYPE    
  SEQUENCE OF  
    MonitorPortEntry

monitorPortEntry 1.3.6.1.4.1.8691.7.69.1.10.3.1
The port table entry of monitor function.
OBJECT-TYPE    
  MonitorPortEntry  

monitorLinkStatus 1.3.6.1.4.1.8691.7.69.1.10.3.1.2
The port link status.
OBJECT-TYPE    
  INTEGER disable(-1), off(0), on(1)  

monitorSpeed 1.3.6.1.4.1.8691.7.69.1.10.3.1.3
The port speed and duplex status.
OBJECT-TYPE    
  INTEGER speed1000M-Full(5), speed1000M-Half(4), speed100M-Full(3), speed100M-Half(2), speed10M-Full(1), speed10M-Half(0), na(-1)  

monitorAutoMDI 1.3.6.1.4.1.8691.7.69.1.10.3.1.4
The port MDI/MDIX status.
OBJECT-TYPE    
  INTEGER auto(2), mdix(1), mdi(0), na(-1)  

monitorTraffic 1.3.6.1.4.1.8691.7.69.1.10.3.1.5
The trafic loading percentage of port.
OBJECT-TYPE    
  INTEGER  

monitorFDXFlowCtrl 1.3.6.1.4.1.8691.7.69.1.10.3.1.6
The Full-Duplex flow control status
OBJECT-TYPE    
  INTEGER off(0), on(1)  

monitorTxTraffic 1.3.6.1.4.1.8691.7.69.1.10.3.1.7
The TX traffic loading percentage of port.
OBJECT-TYPE    
  INTEGER  

monitorRxTraffic 1.3.6.1.4.1.8691.7.69.1.10.3.1.8
The RTX traffic loading percentage of port.
OBJECT-TYPE    
  INTEGER  

monitorDiTable 1.3.6.1.4.1.8691.7.69.1.10.4
The DI table of monitor function.
OBJECT-TYPE    
  SEQUENCE OF  
    MonitorDiEntry

monitorDiEntry 1.3.6.1.4.1.8691.7.69.1.10.4.1
The DI table entry of monitor function.
OBJECT-TYPE    
  MonitorDiEntry  

diIndex 1.3.6.1.4.1.8691.7.69.1.10.4.1.1
The DI index of monitor function
OBJECT-TYPE    
  INTEGER 1..2  

diInputStatus 1.3.6.1.4.1.8691.7.69.1.10.4.1.2
The DI input status.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

monitorFiberCheckTable 1.3.6.1.4.1.8691.7.69.1.10.11
The Fiber Check table of monitor function.
OBJECT-TYPE    
  SEQUENCE OF  
    MonitorFiberCheckEntry

monitorFiberCheckEntry 1.3.6.1.4.1.8691.7.69.1.10.11.1
The fiber check table entry of monitor function.
OBJECT-TYPE    
  MonitorFiberCheckEntry  

fiberPort 1.3.6.1.4.1.8691.7.69.1.10.11.1.1
The fiber index of monitor function
OBJECT-TYPE    
  DisplayString  

fiberModelName 1.3.6.1.4.1.8691.7.69.1.10.11.1.2
The fiber ModelName of monitor function
OBJECT-TYPE    
  DisplayString  

fiberWaveLength 1.3.6.1.4.1.8691.7.69.1.10.11.1.3
The fiber wavelength
OBJECT-TYPE    
  DisplayString  

fiberVoltage 1.3.6.1.4.1.8691.7.69.1.10.11.1.4
The fiber Voltage of monitor function
OBJECT-TYPE    
  DisplayString  

fiberTemperature 1.3.6.1.4.1.8691.7.69.1.10.11.1.5
The fiber Temperature of monitor function
OBJECT-TYPE    
  DisplayString  

fiberTempWarn 1.3.6.1.4.1.8691.7.69.1.10.11.1.6
The Fiber Temperature warning value of monitor function
OBJECT-TYPE    
  DisplayString  

fiberTxPower 1.3.6.1.4.1.8691.7.69.1.10.11.1.7
The fiber TX power of monitor function
OBJECT-TYPE    
  DisplayString  

fiberTxPowerWarn 1.3.6.1.4.1.8691.7.69.1.10.11.1.8
The fiber TX power warning value of monitor function
OBJECT-TYPE    
  DisplayString  

fiberRxPower 1.3.6.1.4.1.8691.7.69.1.10.11.1.9
The fiber RX power of monitor function
OBJECT-TYPE    
  DisplayString  

fiberRxPowerWarn 1.3.6.1.4.1.8691.7.69.1.10.11.1.10
The Fiber RX power warning value of monitor function
OBJECT-TYPE    
  DisplayString  

fiberSN 1.3.6.1.4.1.8691.7.69.1.10.11.1.13
The fiber serial number
OBJECT-TYPE    
  DisplayString  

powerConsumption 1.3.6.1.4.1.8691.7.69.1.10.8
Current power comsuption(Watts). Accurate to second decimal place.
OBJECT-TYPE    
  DisplayString  

emailWarning 1.3.6.1.4.1.8691.7.69.1.11
OBJECT IDENTIFIER    

emailService 1.3.6.1.4.1.8691.7.69.1.11.1
OBJECT IDENTIFIER    

emailWarningSMTPServer 1.3.6.1.4.1.8691.7.69.1.11.1.1
The SMTP server's Ip Address/Domain name of email warning function.
OBJECT-TYPE    
  DisplayString  

emailWarningFirstRecipientEmailAddr 1.3.6.1.4.1.8691.7.69.1.11.1.2
The first recipient email address of email warning function.
OBJECT-TYPE    
  DisplayString  

emailWarningSecondRecipientEmailAddr 1.3.6.1.4.1.8691.7.69.1.11.1.3
The second recipient email address of email warning function.
OBJECT-TYPE    
  DisplayString  

emailWarningThirdRecipientEmailAddr 1.3.6.1.4.1.8691.7.69.1.11.1.4
The third recipient email address of email warning function.
OBJECT-TYPE    
  DisplayString  

emailWarningFourthRecipientEmailAddr 1.3.6.1.4.1.8691.7.69.1.11.1.5
The fourth recipient email address of email warning function.
OBJECT-TYPE    
  DisplayString  

emailWarningSMTPPort 1.3.6.1.4.1.8691.7.69.1.11.1.6
The SMTP server's port of email warning function.
OBJECT-TYPE    
  INTEGER 1..65536  

emailWarningSMTPUser 1.3.6.1.4.1.8691.7.69.1.11.1.7
The registered user account for SMTP service of email warning function.
OBJECT-TYPE    
  DisplayString  

emailWarningSMTPPassword 1.3.6.1.4.1.8691.7.69.1.11.1.8
The registered user password for SMTP service of email warning function.
OBJECT-TYPE    
  DisplayString  

emailWarningSMTPTLS 1.3.6.1.4.1.8691.7.69.1.11.1.9
The SMTP server use TLS of email warning function.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

emailWarningSMTPAuthMethod 1.3.6.1.4.1.8691.7.69.1.11.1.10
The SMTP server use login method of email warning function.
OBJECT-TYPE    
  INTEGER plain(0), login(1), cram-md5(2)  

emailWarningSenderEmailAddr 1.3.6.1.4.1.8691.7.69.1.11.1.11
The sender email address of email warning function.
OBJECT-TYPE    
  DisplayString  

setDeviceIp 1.3.6.1.4.1.8691.7.69.1.12
OBJECT IDENTIFIER    

setDevIpTable 1.3.6.1.4.1.8691.7.69.1.12.1
The set devvice IP table.
OBJECT-TYPE    
  SEQUENCE OF  
    SetDevIpEntry

setDevIpEntry 1.3.6.1.4.1.8691.7.69.1.12.1.1
The set devvice IP table entry.
OBJECT-TYPE    
  SetDevIpEntry  

setDevIpIndex 1.3.6.1.4.1.8691.7.69.1.12.1.1.1
The set devvice IP index.
OBJECT-TYPE    
  INTEGER  

setDevIpCurrentIpofDevice 1.3.6.1.4.1.8691.7.69.1.12.1.1.2
The current IP address of connected to this port.
OBJECT-TYPE    
  DisplayString  

setDevIpPresentBy 1.3.6.1.4.1.8691.7.69.1.12.1.1.3
The protocol used that assigning IP to the device.
OBJECT-TYPE    
  INTEGER no(0), dhcpClient(1), rarp(2), bootp(4)  

setDevIpDedicatedIp 1.3.6.1.4.1.8691.7.69.1.12.1.1.4
The IP address when assign to the device connected to this port.
OBJECT-TYPE    
  IpAddress  

mirroring 1.3.6.1.4.1.8691.7.69.1.13
OBJECT IDENTIFIER    

targetPort 1.3.6.1.4.1.8691.7.69.1.13.1
The mirrored port of mirroring function.
OBJECT-TYPE    
  INTEGER  

mirroringPort 1.3.6.1.4.1.8691.7.69.1.13.2
The mirroring port of mirroring function.
OBJECT-TYPE    
  INTEGER  

monitorDirection 1.3.6.1.4.1.8691.7.69.1.13.3
The traffic direction of mirroring function.
OBJECT-TYPE    
  INTEGER inputDataStream(0), outputDataStream(1), biDirectional(2)  

portTrunking 1.3.6.1.4.1.8691.7.69.1.14
OBJECT IDENTIFIER    

trunkSettingTable 1.3.6.1.4.1.8691.7.69.1.14.1
Port Trunking Setting Table.
OBJECT-TYPE    
  SEQUENCE OF  
    TrunkSettingEntry

trunkSettingEntry 1.3.6.1.4.1.8691.7.69.1.14.1.1
Port Trunking Setting Entry.
OBJECT-TYPE    
  TrunkSettingEntry  

trunkSettingIndex 1.3.6.1.4.1.8691.7.69.1.14.1.1.1
Trunking Group Index.
OBJECT-TYPE    
  INTEGER  

trunkType 1.3.6.1.4.1.8691.7.69.1.14.1.1.2
Trunking Group Type.
OBJECT-TYPE    
  INTEGER static(1), lacp(2)  

trunkMemberPorts 1.3.6.1.4.1.8691.7.69.1.14.1.1.3
Trunking Group Member Ports.
OBJECT-TYPE    
  PortList  

trunkTable 1.3.6.1.4.1.8691.7.69.1.14.2
Port Trunking Table.
OBJECT-TYPE    
  SEQUENCE OF  
    TrunkEntry

trunkEntry 1.3.6.1.4.1.8691.7.69.1.14.2.1
Port Trunking Entry.
OBJECT-TYPE    
  TrunkEntry  

trunkIndex 1.3.6.1.4.1.8691.7.69.1.14.2.1.1
Trunking Group Index.
OBJECT-TYPE    
  INTEGER  

trunkPort 1.3.6.1.4.1.8691.7.69.1.14.2.1.2
Trunking Group Member Port.
OBJECT-TYPE    
  INTEGER  

trunkStatus 1.3.6.1.4.1.8691.7.69.1.14.2.1.3
Trunking Port Status.
OBJECT-TYPE    
  INTEGER success(1), fail(2), standby(3)  

commRedundancy 1.3.6.1.4.1.8691.7.69.1.16
OBJECT IDENTIFIER    

protocolOfRedundancySetup 1.3.6.1.4.1.8691.7.69.1.16.1
This set the redundancy protocol of this switch.
OBJECT-TYPE    
  INTEGER spanningTree(1), turboRing(2), turboRingV2(3), turboChain(4), mstp(5)  

turboRing 1.3.6.1.4.1.8691.7.69.1.16.2
OBJECT IDENTIFIER    

turboRingMaster 2.1
Is this a Master or Slave.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

turboRingMasterSetup 2.2
Set this to be Master.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

turboRingPortTable 2.3
Turbo Ring Port Table.
OBJECT-TYPE    
  SEQUENCE OF  
    TurboRingPortEntry

turboRingPortEntry 2.3.1
Turbo Ring Port Entry.
OBJECT-TYPE    
  TurboRingPortEntry  

turboRingPortIndex 2.3.1.1
Turbo Ring Port Index.
OBJECT-TYPE    
  INTEGER  

turboRingPortStatus 2.3.1.2
Turbo Ring Port Status.
OBJECT-TYPE    
  INTEGER portDisabled(0), notTurboRingPort(1), linkDown(2), blocked(3), learning(4), forwarding(5)  

turboRingPortDesignatedBridge 2.3.1.3
The MAC address of the bridge which this port considers to be the Designated Bridge for this port's segment.
OBJECT-TYPE    
  MacAddress  

turboRingPortDesignatedPort 2.3.1.4
The Port Number of the port on the Designated Bridge for this port's segment.
OBJECT-TYPE    
  INTEGER  

turboRingDesignatedMaster 2.6
The MAC address of the bridge which is the Master of the TURBO RING.
OBJECT-TYPE    
  MacAddress  

turboRingRdntPort1 2.7
The port number of 1st Redundant Port on the TURBO RING.
OBJECT-TYPE    
  INTEGER  

turboRingRdntPort2 2.8
The port number of 2nd Redundant Port on the TURBO RING.
OBJECT-TYPE    
  INTEGER  

turboRingEnableCoupling 2.9
This enable the ring coupling function.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

turboRingCouplingPort 2.10
The coupling port of ring coupling function.
OBJECT-TYPE    
  INTEGER  

turboRingCouplingPortStatus 2.11
The coupling port status of ring coupling function.
OBJECT-TYPE    
  INTEGER portDisabled(0), notCouplingPort(1), linkDown(2), blocked(3), forwarding(5)  

turboRingControlPort 2.12
The control port of ring coupling function.
OBJECT-TYPE    
  INTEGER  

turboRingControlPortStatus 2.13
The control port status of ring coupling function.
OBJECT-TYPE    
  INTEGER portDisabled(0), notControlPort(1), linkDown(2), blocked(3), forwarding(5), inactive(6), active(7)  

turboRingBrokenStatus 2.14
Turbo Ring broken display.
OBJECT-TYPE    
  INTEGER na(0), normal(1), broken(2)  

spanningTree 1.3.6.1.4.1.8691.7.69.1.16.3
OBJECT IDENTIFIER    

spanningTreeRoot 1.1
The root of spanning tree.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

spanningTreeBridgePriority 1.2
The bridge priority of spanning tree protocol.
OBJECT-TYPE    
  INTEGER priority0(0), priority4096(4096), priority8192(8192), priority12288(12288), priority16384(16384), priority20480(20480), priority24576(24576), priority28672(28672), priority32768(32768), priority36864(36864), priority40960(40960), priority45056(45056), priority49152(49152), priority53248(53248), priority57344(57344), priority61440(61440)  

spanningTreeHelloTime 1.3
The hello time of spanning tree protocol.
OBJECT-TYPE    
  INTEGER  

spanningTreeMaxAge 1.4
The max. age of spanning tree protocol.
OBJECT-TYPE    
  INTEGER  

spanningTreeForwardingDelay 1.5
Tje forwarding delay of spanning tree protocol.
OBJECT-TYPE    
  INTEGER  

spanningTreeTable 1.6
The spanning tree table.
OBJECT-TYPE    
  SEQUENCE OF  
    SpanningTreeEntry

spanningTreeEntry 1.6.1
The spanning tree port entry.
OBJECT-TYPE    
  SpanningTreeEntry  

spanningTreeIndex 1.6.1.1
The index of spanning tree table.
OBJECT-TYPE    
  INTEGER  

enableSpanningTree 1.6.1.2
This enable of spanning tree protocol for this port.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

spanningTreePortPriority 1.6.1.3
The port priority of spanning tree protocol.
OBJECT-TYPE    
  INTEGER priority0(0), priority16(16), priority32(32), priority48(48), priority64(64), priority80(80), priority96(96), priority112(112), priority128(128), priority144(144), priority160(160), priority176(176), priority192(192), priority208(208), priority224(224), priority240(240)  

spanningTreePortCost 1.6.1.4
The port cost of spanning tree protocol.
OBJECT-TYPE    
  INTEGER  

spanningTreePortStatus 1.6.1.5
The port status of spanning tree protocol.
OBJECT-TYPE    
  INTEGER portDisabled(0), notSpanningTreePort(1), linkDown(2), blocked(3), learning(4), forwarding(5)  

spanningTreePortEdge 1.6.1.6
This configures the Edge Port property for this port.
OBJECT-TYPE    
  INTEGER auto(0), true(1), false(2)  

activeProtocolOfRedundancy 1.3.6.1.4.1.8691.7.69.1.16.4
This shows the active redundancy protocol of this switch now. The none(0) stauts will be showed if only if the switch's redundancy protocol is set to spanning tree and none of ports enable spanning tree.
OBJECT-TYPE    
  INTEGER none(0), spanningTree(1), turboRing(2), turboRingV2(3), turboChain(4), mstp(5)  

turboRingV2 1.3.6.1.4.1.8691.7.69.1.16.5
OBJECT IDENTIFIER    

turboRingV2Ring1 3.1
OBJECT IDENTIFIER    

ringIndexRing1 3.1.1
The turboRingV2 Ring Index.
OBJECT-TYPE    
  INTEGER 1..2  

ringEnableRing1 3.1.2
The turboRingV2 Ring1 Enalbe Config.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

masterSetupRing1 3.1.3
Is this a Master or Slave.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

masterStatusRing1 3.1.4
Set this to be Master.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

designatedMasterRing1 3.1.5
The MAC address of the bridge which is the Master of the turboRingV2.
OBJECT-TYPE    
  MacAddress  

rdnt1stPortRing1 3.1.6
The port number of 1st Redundant Port on the turboRingV2.
OBJECT-TYPE    
  INTEGER  

rdnt1stPortStatusRing1 3.1.7
The status of 1st Redundant Port on the turboRingV2.
OBJECT-TYPE    
  INTEGER disabled(0), notRedundant(1), linkdown(2), blocking(3), learning(4), forwarding(5)  

rdnt2ndPortRing1 3.1.8
The port number of 2nd Redundant Port on the turboRingV2.
OBJECT-TYPE    
  INTEGER  

rdnt2ndPortStatusRing1 3.1.9
The status of 2nd Redundant Port on the turboRingV2.
OBJECT-TYPE    
  INTEGER disabled(0), notRedundant(1), linkdown(2), blocking(3), learning(4), forwarding(5)  

brokenStatusRing1 3.1.10
turboRingV2 broken display.
OBJECT-TYPE    
  INTEGER na(0), normal(1), broken(2)  

turboRingV2Ring2 3.2
OBJECT IDENTIFIER    

ringIndexRing2 3.2.1
The turboRingV2 Ring Index.
OBJECT-TYPE    
  INTEGER 1..2  

ringEnableRing2 3.2.2
The turboRingV2 Ring2 Enalbe Config.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

masterSetupRing2 3.2.3
Is this a Master or Slave.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

masterStatusRing2 3.2.4
Set this to be Master.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

designatedMasterRing2 3.2.5
The MAC address of the bridge which is the Master of the turboRingV2.
OBJECT-TYPE    
  MacAddress  

rdnt1stPortRing2 3.2.6
The port number of 1st Redundant Port on the turboRingV2.
OBJECT-TYPE    
  INTEGER  

rdnt1stPortStatusRing2 3.2.7
The status of 1st Redundant Port on the turboRingV2.
OBJECT-TYPE    
  INTEGER disabled(0), notRedundant(1), linkdown(2), blocking(3), learning(4), forwarding(5)  

rdnt2ndPortRing2 3.2.8
The port number of 2nd Redundant Port on the turboRingV2.
OBJECT-TYPE    
  INTEGER  

rdnt2ndPortStatusRing2 3.2.9
The status of 2nd Redundant Port on the turboRingV2.
OBJECT-TYPE    
  INTEGER disabled(0), notRedundant(1), linkdown(2), blocking(3), learning(4), forwarding(5)  

brokenStatusRing2 3.2.10
turboRingV2 broken display.
OBJECT-TYPE    
  INTEGER na(0), normal(1), broken(2)  

turboRingV2Coupling 3.3
OBJECT IDENTIFIER    

couplingEnable 3.3.1
Setting the ring coupling enable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

couplingMode 3.3.2
Setting the ring coupling mode.
OBJECT-TYPE    
  INTEGER dualHoming(1), couplingBackup(2), couplingPrimary(3)  

coupling1stPort 3.3.3
If in 'DUAL HOMING' mode,port name is 'Primary port',If in 'COUPLING' mode,port name is 'Coupling port'
OBJECT-TYPE    
  INTEGER  

coupling1stPortStatus 3.3.4
The 1st coupling port status of coupling function.
OBJECT-TYPE    
  INTEGER disabled(0), notRedundant(1), linkdown(2), blocking(3), learning(4), forwarding(5)  

coupling2ndPort 3.3.5
If in 'DUAL HOMING' mode,port name is 'Backup port',If in 'COUPLING' mode,port name is no used.
OBJECT-TYPE    
  INTEGER  

coupling2ndPortStatus 3.3.6
The 2nd coupling port status of coupling function.
OBJECT-TYPE    
  INTEGER disabled(0), notRedundant(1), linkdown(2), blocking(3), learning(4), forwarding(5)  

turboChain 1.3.6.1.4.1.8691.7.69.1.16.6
OBJECT IDENTIFIER    

turboChainRole 4.1
The Role of TURBO CHAIN.
OBJECT-TYPE    
  INTEGER head(1), member(2), tail(3)  

turboChainPort1 4.2
The port number of 1st Redundant Port on the TURBO CHAIN. If switch role is Turbo Chain Head, this is Head port, If Switch role is Turbo Chain Tail, this is Tail port.
OBJECT-TYPE    
  INTEGER  

turboChainPort2 4.3
The port number of 2nd Redundant Port on the TURBO CHAIN. It is the member port of TurboChain
OBJECT-TYPE    
  INTEGER  

turboChainPort1Status 4.4
Turbo Chain Port Status.
OBJECT-TYPE    
  INTEGER notTurboChainPort(0), linkDown(1), blocking(2), blocked(3), forwarding(4), na(5)  

turboChainPort2Status 4.5
Turbo Chain Port Status.
OBJECT-TYPE    
  INTEGER notTurboChainPort(0), linkDown(1), blocking(2), blocked(3), forwarding(4), na(5)  

turboChainPort1PartnerBridge 4.6
The MAC address of the next bridge
OBJECT-TYPE    
  MacAddress  

turboChainPort2PartnerBridge 4.7
The MAC address of the neighbor Turbo Chain switch
OBJECT-TYPE    
  MacAddress  

relayWarning 1.3.6.1.4.1.8691.7.69.1.17
OBJECT IDENTIFIER    

relayWarningTable 1.3.6.1.4.1.8691.7.69.1.17.11
The relay warning table.
OBJECT-TYPE    
  SEQUENCE OF  
    RelayWarningEntry

relayWarningEntry 1.3.6.1.4.1.8691.7.69.1.17.11.1
Relay Warning Entry.
OBJECT-TYPE    
  RelayWarningEntry  

relayAlarmIndex 1.3.6.1.4.1.8691.7.69.1.17.11.1.1
The Relay alarm index.
OBJECT-TYPE    
  INTEGER  

relayWarningRelayContact 1.3.6.1.4.1.8691.7.69.1.17.11.1.2
The first Relay contact status.
OBJECT-TYPE    
  INTEGER closed(0), opened(1)  

overrideRelayWarningSetting 1.3.6.1.4.1.8691.7.69.1.17.11.1.3
Override the relay warning setting.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

relayWarningPower1Off 1.3.6.1.4.1.8691.7.69.1.17.11.1.4
The relay contact will be opened while the first power input off.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

relayWarningPower1OffStatus 1.3.6.1.4.1.8691.7.69.1.17.11.1.5
The relay contact is opened as the first power input off..
OBJECT-TYPE    
  INTEGER not-triggered(0), triggered(1)  

relayWarningPower2Off 1.3.6.1.4.1.8691.7.69.1.17.11.1.6
The relay contact will be opened while the second power input off.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

relayWarningPower2OffStatus 1.3.6.1.4.1.8691.7.69.1.17.11.1.7
The relay contact is opened as the second power input off.
OBJECT-TYPE    
  INTEGER not-triggered(0), triggered(1)  

relayWarningTurboRingBreak 1.3.6.1.4.1.8691.7.69.1.17.11.1.8
The relay contact will be opened while turbo ring break.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

relayWarningTurboRingBreakStatus 1.3.6.1.4.1.8691.7.69.1.17.11.1.9
The relay contact is opened while turbo ring is broken.
OBJECT-TYPE    
  INTEGER not-triggered(0), triggered(1)  

portRelayWarningTable 1.3.6.1.4.1.8691.7.69.1.17.12
The relay warning port table.
OBJECT-TYPE    
  SEQUENCE OF  
    PortRelayWarningEntry

portRelayWarningEntry 1.3.6.1.4.1.8691.7.69.1.17.12.1
Port Relay Warning Entry.
OBJECT-TYPE    
  PortRelayWarningEntry  

relayWarningLinkChanged 1.3.6.1.4.1.8691.7.69.1.17.12.1.1
The relay contact will be opened while this port's link status is changed.
OBJECT-TYPE    
  INTEGER ignore(0), on2off(1), off2on(2)  

relayWarningLinkChangedStatus 1.3.6.1.4.1.8691.7.69.1.17.12.1.2
The relay contact is opened as this port's link status is changed.
OBJECT-TYPE    
  INTEGER not-triggered(0), triggered(1)  

relayWarningTrafficOverload 1.3.6.1.4.1.8691.7.69.1.17.12.1.3
The relay contact will be opened while this port's traffic is overload.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

relayWarningTrafficOverloadStatus 1.3.6.1.4.1.8691.7.69.1.17.12.1.4
The relay contact is opened as this port's traffic is overload.
OBJECT-TYPE    
  INTEGER not-triggered(0), triggered(1)  

relayWarningRxTrafficThreshold 1.3.6.1.4.1.8691.7.69.1.17.12.1.5
The threshold of the port traffic will be over loading.
OBJECT-TYPE    
  INTEGER  

relayWarningTrafficDuration 1.3.6.1.4.1.8691.7.69.1.17.12.1.6
The duration of the port traffic will be over loading.
OBJECT-TYPE    
  INTEGER  

diRelayWarningTable 1.3.6.1.4.1.8691.7.69.1.17.13
The relay warning DI table.
OBJECT-TYPE    
  SEQUENCE OF  
    DiRelayWarningEntry

diRelayWarningEntry 1.3.6.1.4.1.8691.7.69.1.17.13.1
DI Relay Warning Entry.
OBJECT-TYPE    
  DiRelayWarningEntry  

relayWarningDiInputChanged 1.3.6.1.4.1.8691.7.69.1.17.13.1.1
The relay contact will be opened while the DI input changed.
OBJECT-TYPE    
  INTEGER disable(0), off(1), on(2)  

relayWarningDiInputChangedStatus 1.3.6.1.4.1.8691.7.69.1.17.13.1.2
The relay contact is opened as the first DI input changed..
OBJECT-TYPE    
  INTEGER not-triggered(0), triggered(1)  

trafficPrioritization 1.3.6.1.4.1.8691.7.69.1.18
OBJECT IDENTIFIER    

qosClassification 1.3.6.1.4.1.8691.7.69.1.18.1
OBJECT IDENTIFIER    

schedulingMechanism 1.3.6.1.4.1.8691.7.69.1.18.1.1
The scheduling mechanism.
OBJECT-TYPE    
  INTEGER schedweightfair(0), schedstrict(1)  

qosPortTable 1.3.6.1.4.1.8691.7.69.1.18.1.2
The QoS port table.
OBJECT-TYPE    
  SEQUENCE OF  
    QosPortEntry

qosPortEntry 1.3.6.1.4.1.8691.7.69.1.18.1.2.1
The QoS Port Entry.
OBJECT-TYPE    
  QosPortEntry  

dscpInspection 1.3.6.1.4.1.8691.7.69.1.18.1.2.1.1
This enable the inspection of dscp field.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

cosInspection 1.3.6.1.4.1.8691.7.69.1.18.1.2.1.2
This enable the inspection of CoS field.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

portPriority 1.3.6.1.4.1.8691.7.69.1.18.1.2.1.3
The deault priority of the port.
OBJECT-TYPE    
  INTEGER priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7)  

priorityMapping 1.3.6.1.4.1.8691.7.69.1.18.2
OBJECT IDENTIFIER    

priorityMappingTable 1.3.6.1.4.1.8691.7.69.1.18.2.1
The priority mapping table.
OBJECT-TYPE    
  SEQUENCE OF  
    PriorityMappingEntry

priorityMappingEntry 1.3.6.1.4.1.8691.7.69.1.18.2.1.1
The Priority mapping Entry.
OBJECT-TYPE    
  PriorityMappingEntry  

priorityTag 1.3.6.1.4.1.8691.7.69.1.18.2.1.1.1
The priority tag of QOS field.
OBJECT-TYPE    
  INTEGER 0..7  

priorityMappedQueue 1.3.6.1.4.1.8691.7.69.1.18.2.1.1.2
The egress queue corresponding to it's priority value.
OBJECT-TYPE    
  INTEGER trafficclass0(0), trafficclass1(1), trafficclass2(2), trafficclass3(3)  

dscpMapping 1.3.6.1.4.1.8691.7.69.1.18.3
OBJECT IDENTIFIER    

dscpMappingTable 1.3.6.1.4.1.8691.7.69.1.18.3.1
The DSCP mapping table.
OBJECT-TYPE    
  SEQUENCE OF  
    DscpMappingEntry

dscpMappingEntry 1.3.6.1.4.1.8691.7.69.1.18.3.1.1
DSCP mapping Entry.
OBJECT-TYPE    
  DscpMappingEntry  

dscpClass 1.3.6.1.4.1.8691.7.69.1.18.3.1.1.1
The DSCP class of TOS field.
OBJECT-TYPE    
  INTEGER  

dscpMappedPriority 1.3.6.1.4.1.8691.7.69.1.18.3.1.1.2
The frame's priority corresponding to it's DSCP class value.
OBJECT-TYPE    
  INTEGER priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7)  

vlan 1.3.6.1.4.1.8691.7.69.1.19
OBJECT IDENTIFIER    

vlanPortSettingTable 1.3.6.1.4.1.8691.7.69.1.19.1
The vlan seting table of ports.
OBJECT-TYPE    
  SEQUENCE OF  
    VlanPortSettingEntry

vlanPortSettingEntry 1.3.6.1.4.1.8691.7.69.1.19.1.1
Port Setting Entry of VLAN.
OBJECT-TYPE    
  VlanPortSettingEntry  

portVlanType 1.3.6.1.4.1.8691.7.69.1.19.1.1.1
The vlan type of port.
OBJECT-TYPE    
  INTEGER access(0), trunk(1), hybrid(2)  

portDefaultVid 1.3.6.1.4.1.8691.7.69.1.19.1.1.2
The PVID of port.
OBJECT-TYPE    
  INTEGER 1..4094  

portFixedVid 1.3.6.1.4.1.8691.7.69.1.19.1.1.3
The fixed vids of (trunk) port.
OBJECT-TYPE    
  DisplayString  

portForbiddenVid 1.3.6.1.4.1.8691.7.69.1.19.1.1.4
The forbidden vids of (trunk)port.
OBJECT-TYPE    
  DisplayString  

portFixedVidUntag 1.3.6.1.4.1.8691.7.69.1.19.1.1.5
The fixed untag vids of (trunk) port.
OBJECT-TYPE    
  DisplayString  

vlanTable 1.3.6.1.4.1.8691.7.69.1.19.2
The VLAN table.
OBJECT-TYPE    
  SEQUENCE OF  
    VlanEntry

vlanEntry 1.3.6.1.4.1.8691.7.69.1.19.2.1
VLAN Entry.
OBJECT-TYPE    
  VlanEntry  

vlanId 1.3.6.1.4.1.8691.7.69.1.19.2.1.1
The VLAN id.
OBJECT-TYPE    
  INTEGER 1..4094  

joinedAccessPorts 1.3.6.1.4.1.8691.7.69.1.19.2.1.2
The access ports that joined this VID.
OBJECT-TYPE    
  PortList  

joinedTrunkPorts 1.3.6.1.4.1.8691.7.69.1.19.2.1.3
The trunk ports that joined this VID.
OBJECT-TYPE    
  PortList  

joinedHybridPorts 1.3.6.1.4.1.8691.7.69.1.19.2.1.4
The hybrid ports that joined this VID.
OBJECT-TYPE    
  PortList  

vlanName 1.3.6.1.4.1.8691.7.69.1.19.2.1.5
The VLAN name.
OBJECT-TYPE    
  DisplayString  

managementVlanId 1.3.6.1.4.1.8691.7.69.1.19.3
The management VLAN id.
OBJECT-TYPE    
  INTEGER  

vlanType 1.3.6.1.4.1.8691.7.69.1.19.4
VLAN Type.
OBJECT-TYPE    
  INTEGER tagBased(0), portBased(1)  

portbaseVlanSettingTable 1.3.6.1.4.1.8691.7.69.1.19.5
Port base Vlan Setting Table.
OBJECT-TYPE    
  SEQUENCE OF  
    PortbaseVlanSettingEntry

portbaseVlanSettingEntry 1.3.6.1.4.1.8691.7.69.1.19.5.1
Port base Vlan Setting Entry.
OBJECT-TYPE    
  PortbaseVlanSettingEntry  

portbaseVlanSettingIndex 1.3.6.1.4.1.8691.7.69.1.19.5.1.1
port base Vlan Group Index.
OBJECT-TYPE    
  INTEGER  

portbaseVlanMemberPorts 1.3.6.1.4.1.8691.7.69.1.19.5.1.2
port base Vlan Group Member Ports.
OBJECT-TYPE    
  PortList  

enableGvrp 1.3.6.1.4.1.8691.7.69.1.19.6
Enable GVRP.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

multicastFiltering 1.3.6.1.4.1.8691.7.69.1.20
OBJECT IDENTIFIER    

igmpSnooping 1.3.6.1.4.1.8691.7.69.1.20.1
OBJECT IDENTIFIER    

querierQueryInterval 1.3.6.1.4.1.8691.7.69.1.20.1.1
This query interval of the querier function for this VLAN.
OBJECT-TYPE    
  INTEGER 20..600  

igmpSnoopingSettingTable 1.3.6.1.4.1.8691.7.69.1.20.1.2
The IGMP snooping setting table.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopingSettingEntry

igmpSnoopingSettingEntry 1.3.6.1.4.1.8691.7.69.1.20.1.2.1
The IGMP snooping setting Entry.
OBJECT-TYPE    
  IgmpSnoopingSettingEntry  

enableIgmpSnooping 1.3.6.1.4.1.8691.7.69.1.20.1.2.1.1
This enable the IGMP snooping functon in this VLAN.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

enableQuerier 1.3.6.1.4.1.8691.7.69.1.20.1.2.1.2
This enable the querier function for this VLAN.
OBJECT-TYPE    
  INTEGER disable(0), igmpv2(1), igmpv3(2)  

fixedMulticastQuerierPorts 1.3.6.1.4.1.8691.7.69.1.20.1.2.1.3
The ports that multicast-Querier exist.
OBJECT-TYPE    
  PortList  

learnedMulticastQuerierPorts 1.3.6.1.4.1.8691.7.69.1.20.1.2.1.4
The ports that multicast-Querier exist.
OBJECT-TYPE    
  PortList  

enableGlobalIgmpSnooping 1.3.6.1.4.1.8691.7.69.1.20.1.4
This enable the IGMP snooping functon .
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

multicastFastForwarding 1.3.6.1.4.1.8691.7.69.1.20.1.7
This Enable Multicast Fast Forwarding Mode functon .
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

staticMulticast 1.3.6.1.4.1.8691.7.69.1.20.2
OBJECT IDENTIFIER    

staticMulticastTable 1.3.6.1.4.1.8691.7.69.1.20.2.1
The static multicast table.
OBJECT-TYPE    
  SEQUENCE OF  
    StaticMulticastEntry

staticMulticastEntry 1.3.6.1.4.1.8691.7.69.1.20.2.1.1
Static multicast Entry.
OBJECT-TYPE    
  StaticMulticastEntry  

staticMulticastAddress 1.3.6.1.4.1.8691.7.69.1.20.2.1.1.1
The static multicast address.
OBJECT-TYPE    
  MacAddress  

staticMulticastPorts 1.3.6.1.4.1.8691.7.69.1.20.2.1.1.2
The port map of the static multicast address.
OBJECT-TYPE    
  PortList  

staticMulticastStatus 1.3.6.1.4.1.8691.7.69.1.20.2.1.1.3
The status is active to indicate normal. Use createAndGo to create new on multiple SET. Use createAndWait to create new on one SET all then actvie. Use destroy to delete this row.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4), createAndWait(5), destroy(6)  

gmrp 1.3.6.1.4.1.8691.7.69.1.20.3
OBJECT IDENTIFIER    

gmrpSettingTable 1.3.6.1.4.1.8691.7.69.1.20.3.1
The GMRP setting table.
OBJECT-TYPE    
  SEQUENCE OF  
    GmrpSettingEntry

gmrpSettingEntry 1.3.6.1.4.1.8691.7.69.1.20.3.1.1
The GMRP Setting Entry.
OBJECT-TYPE    
  GmrpSettingEntry  

enableGMRP 1.3.6.1.4.1.8691.7.69.1.20.3.1.1.1
Enable/Disable GMRP.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

gmrpTable 1.3.6.1.4.1.8691.7.69.1.20.3.2
The GMRP status table.
OBJECT-TYPE    
  SEQUENCE OF  
    GmrpEntry

gmrpEntry 1.3.6.1.4.1.8691.7.69.1.20.3.2.1
The GMRP Status Entry.
OBJECT-TYPE    
  GmrpEntry  

gmrpMulticastGroup 1.3.6.1.4.1.8691.7.69.1.20.3.2.1.1
GMRP multicast group.
OBJECT-TYPE    
  MacAddress  

gmrpFixedPorts 1.3.6.1.4.1.8691.7.69.1.20.3.2.1.2
The ports that joined GMRP multicast group manually.
OBJECT-TYPE    
  PortList  

gmrpLearnedPorts 1.3.6.1.4.1.8691.7.69.1.20.3.2.1.3
The ports that joined GMRP multicast group by GMRP learning.
OBJECT-TYPE    
  PortList  

rateLimiting 1.3.6.1.4.1.8691.7.69.1.21
OBJECT IDENTIFIER    

rateLimitingAction 1.3.6.1.4.1.8691.7.69.1.21.4
The rate limiting mode.
OBJECT-TYPE    
  INTEGER droppacket(0), portDisable(1)  

droppacketModeRateLimitingIngressTable 1.3.6.1.4.1.8691.7.69.1.21.1
The rate limiting table.
OBJECT-TYPE    
  SEQUENCE OF  
    DroppacketModeRateLimitingIngressEntry

droppacketModeRateLimitingIngressEntry 1.3.6.1.4.1.8691.7.69.1.21.1.1
Rate limiting Entry.
OBJECT-TYPE    
  DroppacketModeRateLimitingIngressEntry  

ingressLimitRate 1.3.6.1.4.1.8691.7.69.1.21.1.1.1
The ingress limit mode.
OBJECT-TYPE    
  INTEGER notlimited(0), percentage03(1), percentage05(2), percentage10(3), percentage15(4), percentage25(5), percentage35(6), percentage50(7), percentage65(8), percentage85(9)  

broadcastStormProtection 1.3.6.1.4.1.8691.7.69.1.21.2
OBJECT IDENTIFIER    

bcastStormProtection 1.3.6.1.4.1.8691.7.69.1.21.2.1
Broadcast Storm Protection
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bcastStormProtectionIncludeMcast 1.3.6.1.4.1.8691.7.69.1.21.2.2
Broadcast Storm Protection includes Multicast packets
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bcastStormProtectionIncludeUcast 1.3.6.1.4.1.8691.7.69.1.21.2.3
Broadcast Storm Protection includes Unicast packets
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

portDisableMode 1.3.6.1.4.1.8691.7.69.1.21.3
OBJECT IDENTIFIER    

portDisableModePeriod 1.3.6.1.4.1.8691.7.69.1.21.3.1
Check time.
OBJECT-TYPE    
  INTEGER 1..65535  

portDisableModeTable 1.3.6.1.4.1.8691.7.69.1.21.3.2
The rate limiting table.
OBJECT-TYPE    
  SEQUENCE OF  
    PortDisableModeEntry

portDisableModeEntry 1.3.6.1.4.1.8691.7.69.1.21.3.2.1
Rate limiting Entry.
OBJECT-TYPE    
  PortDisableModeEntry  

ingressLimit 1.3.6.1.4.1.8691.7.69.1.21.3.2.1.1
The ingress limit mode.
OBJECT-TYPE    
  INTEGER notlimited(0), rateMega1Fps4464(1), rateMega2Fps7441(2), rateMega3Fps14881(3), rateMega4Fps22322(4), rateMega5Fps37203(5), rateMega6Fps52084(6), rateMega7Fps74405(7), rateGiga1Fps44640(8), rateGiga2Fps74410(9), rateGiga3Fps148810(10), rateGiga4Fps223220(11), rateGiga5Fps372030(12), rateGiga6Fps520840(13), rateGiga7Fps744050(14)  

security 1.3.6.1.4.1.8691.7.69.1.22
OBJECT IDENTIFIER    

userLoginSetting 1.3.6.1.4.1.8691.7.69.1.22.1
OBJECT IDENTIFIER    

userLoginServer 1.3.6.1.4.1.8691.7.69.1.22.1.1
Set user login server option.
OBJECT-TYPE    
  INTEGER tacacsLocal(1), radiusLocal(2), tacacs(3), radius(4), local(5)  

tacacsServerSetting 1.3.6.1.4.1.8691.7.69.1.22.1.2
OBJECT IDENTIFIER    

tacacsLoginAuthServer 1.3.6.1.4.1.8691.7.69.1.22.1.2.1
Set Tacacs+ Server IP Address/Domain name.
OBJECT-TYPE    
  DisplayString  

tacacsLoginAuthPort 1.3.6.1.4.1.8691.7.69.1.22.1.2.2
Set Tacacs+ Port.
OBJECT-TYPE    
  INTEGER 1..65535  

tacacsLoginAuthSharedKey 1.3.6.1.4.1.8691.7.69.1.22.1.2.3
Set Tacacs+ Shared Key.
OBJECT-TYPE    
  DisplayString  

tacacsLoginAuthAuthType 1.3.6.1.4.1.8691.7.69.1.22.1.2.4
Set Tacacs+ Shared Key.
OBJECT-TYPE    
  INTEGER ascii(0), pap(1), chap(2), mschap(4)  

tacacsLoginAuthTimeout 1.3.6.1.4.1.8691.7.69.1.22.1.2.5
Set Tacacs+ Shared Key.
OBJECT-TYPE    
  INTEGER 1..255  

radiusServerSetting 1.3.6.1.4.1.8691.7.69.1.22.1.3
OBJECT IDENTIFIER    

radiusLoginAuthServer 1.3.6.1.4.1.8691.7.69.1.22.1.3.1
Set Radius Server IP Address/Domain name.
OBJECT-TYPE    
  DisplayString  

radiusLoginAuthPort 1.3.6.1.4.1.8691.7.69.1.22.1.3.2
Set Radius Port.
OBJECT-TYPE    
  INTEGER 1..65535  

radiusLoginAuthSharedKey 1.3.6.1.4.1.8691.7.69.1.22.1.3.3
Set Radius Shared Key.
OBJECT-TYPE    
  DisplayString  

radiusLoginAuthAuthType 1.3.6.1.4.1.8691.7.69.1.22.1.3.4
Set Radius Shared Key.
OBJECT-TYPE    
  INTEGER pap(0), chap(1)  

radiusLoginAuthTimeout 1.3.6.1.4.1.8691.7.69.1.22.1.3.5
Set Radius Shared Key.
OBJECT-TYPE    
  INTEGER 1..255  

portAccessControl 1.3.6.1.4.1.8691.7.69.1.22.2
OBJECT IDENTIFIER    

staticPortLockLegacy 1.3.6.1.4.1.8691.7.69.1.22.2.1
OBJECT IDENTIFIER    

staticPortLockLegacyAddress 1.3.6.1.4.1.8691.7.69.1.22.2.1.1
The static port lock address.
OBJECT-TYPE    
  MacAddress  

staticPortLockLegacyPort 1.3.6.1.4.1.8691.7.69.1.22.2.1.2
The port of the static port lock address.
OBJECT-TYPE    
  INTEGER  

staticPortLockLegacyStatus 1.3.6.1.4.1.8691.7.69.1.22.2.1.3
The status is active to indicate normal. Use createAndGo to create new on multiple SET.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4)  

dot1x 1.3.6.1.4.1.8691.7.69.1.22.2.2
OBJECT IDENTIFIER    

dataBaseOption 1.3.6.1.4.1.8691.7.69.1.22.2.2.1
Set IEEE 802.1X database option.
OBJECT-TYPE    
  INTEGER local(1), radius(2), radiuslocal(3)  

dot1xReauthEnable 1.3.6.1.4.1.8691.7.69.1.22.2.2.5
Enable/Disable IEEE 802.1X Re-authentication.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

dot1xReauthPeriod 1.3.6.1.4.1.8691.7.69.1.22.2.2.6
Set IEEE 802.1X Re-authentication Period.
OBJECT-TYPE    
  INTEGER 60..3600  

dot1xSettingTable 1.3.6.1.4.1.8691.7.69.1.22.2.2.7
IEEE 802.1X Port Setting Table.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1xSettingEntry

dot1xSettingEntry 1.3.6.1.4.1.8691.7.69.1.22.2.2.7.1
IEEE 802.1X Port Setting Entry.
OBJECT-TYPE    
  Dot1xSettingEntry  

enableDot1X 1.3.6.1.4.1.8691.7.69.1.22.2.2.7.1.1
Enable/Disable IEEE 802.1X.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

dot1xReauthTable 1.3.6.1.4.1.8691.7.69.1.22.2.2.8
IEEE 802.1X Re-authentication Table.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1xReauthEntry

dot1xReauthEntry 1.3.6.1.4.1.8691.7.69.1.22.2.2.8.1
IEEE 802.1X Re-authentication Entry.
OBJECT-TYPE    
  Dot1xReauthEntry  

dot1xReauthPortIndex 1.3.6.1.4.1.8691.7.69.1.22.2.2.8.1.1
IEEE 802.1X Enabled Port Index.
OBJECT-TYPE    
  INTEGER  

dot1xReauth 1.3.6.1.4.1.8691.7.69.1.22.2.2.8.1.2
Reauth IEEE 802.1X.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

dot1xRadius 1.3.6.1.4.1.8691.7.69.1.22.2.2.9
OBJECT IDENTIFIER    

dot1xSameAsAuthServer 1.3.6.1.4.1.8691.7.69.1.22.2.2.9.1
Set Radius Server IP Address/Domain name.
OBJECT-TYPE    
  INTEGER notSame(0), same(1)  

dot1x1stRadiusServer 1.3.6.1.4.1.8691.7.69.1.22.2.2.9.2
Set Radius Server IP Address/Domain name.
OBJECT-TYPE    
  DisplayString  

dot1x1stRadiusPort 1.3.6.1.4.1.8691.7.69.1.22.2.2.9.3
Set Radius Port.
OBJECT-TYPE    
  INTEGER 1..65535  

dot1x1stRadiusSharedKey 1.3.6.1.4.1.8691.7.69.1.22.2.2.9.4
Set Radius Shared Key.
OBJECT-TYPE    
  DisplayString  

dot1x2ndRadiusServer 1.3.6.1.4.1.8691.7.69.1.22.2.2.9.5
Set Radius Server IP Address/Domain name.
OBJECT-TYPE    
  DisplayString  

dot1x2ndRadiusPort 1.3.6.1.4.1.8691.7.69.1.22.2.2.9.6
Set Radius Port.
OBJECT-TYPE    
  INTEGER 1..65535  

dot1x2ndRadiusSharedKey 1.3.6.1.4.1.8691.7.69.1.22.2.2.9.7
Set Radius Shared Key.
OBJECT-TYPE    
  DisplayString  

portAccessControlTable 1.3.6.1.4.1.8691.7.69.1.22.2.3
The Port Access Control table.
OBJECT-TYPE    
  SEQUENCE OF  
    PortAccessControlEntry

portAccessControlEntry 1.3.6.1.4.1.8691.7.69.1.22.2.3.1
The Port Access Control table entry.
OBJECT-TYPE    
  PortAccessControlEntry  

portAccessControlAddress 1.3.6.1.4.1.8691.7.69.1.22.2.3.1.1
The MAC address which is static locked or IEEE 802.1X authorized.
OBJECT-TYPE    
  MacAddress  

portAccessControlPortNo 1.3.6.1.4.1.8691.7.69.1.22.2.3.1.2
The port number that the Port Access Control address resides.
OBJECT-TYPE    
  INTEGER  

portAccessControlAccessStatus 1.3.6.1.4.1.8691.7.69.1.22.2.3.1.3
The access status of the Port Access Control address.
OBJECT-TYPE    
  INTEGER staticLock(1), authorized(2), unAuthorized(3), authorizing(4), macAddrSticky(5)  

portAccessControlStatus 1.3.6.1.4.1.8691.7.69.1.22.2.3.1.4
The status is active to indicate normal. Use createAndGo to create new on multiple SET. Use createAndWait to create new on one SET all then actvie. Use destroy to delete this row.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4), createAndWait(5), destroy(6)  

portAccessControlVid 1.3.6.1.4.1.8691.7.69.1.22.2.3.1.5
The vid number that the Port Access Control address resides.
OBJECT-TYPE    
  INTEGER  

portSecurity 1.3.6.1.4.1.8691.7.69.1.22.2.4
OBJECT IDENTIFIER    

portSecurityModeTable 1.3.6.1.4.1.8691.7.69.1.22.2.4.1
Port security mode
OBJECT-TYPE    
  SEQUENCE OF  
    PortSecurityModeEntry

portSecurityModeEntry 1.3.6.1.4.1.8691.7.69.1.22.2.4.1.1
Port security mode entry.
OBJECT-TYPE    
  PortSecurityModeEntry  

portSecurityModePort 1.3.6.1.4.1.8691.7.69.1.22.2.4.1.1.1
Set port security mode to specific port.
OBJECT-TYPE    
  INTEGER  

portSecurityModeSelect 1.3.6.1.4.1.8691.7.69.1.22.2.4.1.1.2
Select the port security mode of the port.
OBJECT-TYPE    
  INTEGER normal-mode(0), static-portlock(1), mac-address-sticky(2)  

portSecurityModeLimit 1.3.6.1.4.1.8691.7.69.1.22.2.4.1.1.3
If port security mode is MAC address sticky, set the limit of the port. If port security mode is not MAC address sticky, set the limit to 0.
OBJECT-TYPE    
  INTEGER  

portSecurityModeViolationPortDisable 1.3.6.1.4.1.8691.7.69.1.22.2.4.1.1.4
Enable the violation port disable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

portSecurityModeStatus 1.3.6.1.4.1.8691.7.69.1.22.2.4.1.1.5
The status is active to indicate normal. Use createAndGo to create new on multiple SET.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4)  

staticPortLock 1.3.6.1.4.1.8691.7.69.1.22.2.4.2
OBJECT IDENTIFIER    

staticPortLockAddress 1.3.6.1.4.1.8691.7.69.1.22.2.4.2.1
The static port lock address.
OBJECT-TYPE    
  MacAddress  

staticPortLockPort 1.3.6.1.4.1.8691.7.69.1.22.2.4.2.2
The port of the static port lock address.
OBJECT-TYPE    
  INTEGER  

staticPortLockStatus 1.3.6.1.4.1.8691.7.69.1.22.2.4.2.3
The status is active to indicate normal. Use createAndGo to create new on multiple SET.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4)  

staticPortLockVid 1.3.6.1.4.1.8691.7.69.1.22.2.4.2.4
Add vlan of the static port lock address. For SVL switch, vid should be 0
OBJECT-TYPE    
  INTEGER  

macAddressSticky 1.3.6.1.4.1.8691.7.69.1.22.2.4.3
OBJECT IDENTIFIER    

macAddressStickyAddress 1.3.6.1.4.1.8691.7.69.1.22.2.4.3.1
Manually add a MAC sticky address.
OBJECT-TYPE    
  MacAddress  

macAddressStickyPort 1.3.6.1.4.1.8691.7.69.1.22.2.4.3.2
Add MAC sticky address to the specific port.
OBJECT-TYPE    
  INTEGER  

macAddressStickyVid 1.3.6.1.4.1.8691.7.69.1.22.2.4.3.3
Add MAC sticky address to the specific vlan. For SVL switch, vid should be 0
OBJECT-TYPE    
  INTEGER  

macAddressStickyStatus 1.3.6.1.4.1.8691.7.69.1.22.2.4.3.4
The status is active to indicate normal. Use createAndGo to create new on multiple SET.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4)  

mab 1.3.6.1.4.1.8691.7.69.1.22.2.5
OBJECT IDENTIFIER    

mabDBOption 1.3.6.1.4.1.8691.7.69.1.22.2.5.1
Set MAB database option.
OBJECT-TYPE    
  INTEGER radius(2)  

mabReauthEnable 1.3.6.1.4.1.8691.7.69.1.22.2.5.2
Enable/Disable MAB Re-authorizing.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

mabReauthPeriod 1.3.6.1.4.1.8691.7.69.1.22.2.5.3
Set MAB Re-authorizing Period.
OBJECT-TYPE    
  INTEGER 60..65535  

mabRestartEnable 1.3.6.1.4.1.8691.7.69.1.22.2.5.4
Enable/Disable MAB Re-start.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

mabRestartPeriod 1.3.6.1.4.1.8691.7.69.1.22.2.5.5
Set MAB Re-start Period.
OBJECT-TYPE    
  INTEGER 5..300  

mabSettingTable 1.3.6.1.4.1.8691.7.69.1.22.2.5.6
MAB Setting Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MABSettingEntry

mabSettingEntry 1.3.6.1.4.1.8691.7.69.1.22.2.5.6.1
MAB Port Setting Entry.
OBJECT-TYPE    
  MABSettingEntry  

enableMAB 1.3.6.1.4.1.8691.7.69.1.22.2.5.6.1.1
Enable/Disable MAB.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

accessibleIP 1.3.6.1.4.1.8691.7.69.1.30
OBJECT IDENTIFIER    

enableAccessibleIP 1.3.6.1.4.1.8691.7.69.1.30.1
Enable the accessible IP address list.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

accessibleIpTable 1.3.6.1.4.1.8691.7.69.1.30.2
accessibleIP.
OBJECT-TYPE    
  SEQUENCE OF  
    AccessibleIpEntry

accessibleIpEntry 1.3.6.1.4.1.8691.7.69.1.30.2.1
Accessible IP address entry.
OBJECT-TYPE    
  AccessibleIpEntry  

accessibleIpAddress 1.3.6.1.4.1.8691.7.69.1.30.2.1.1
Accessible IP address
OBJECT-TYPE    
  IpAddress  

accessibleIpNetMask 1.3.6.1.4.1.8691.7.69.1.30.2.1.2
Accessible IP netmask.
OBJECT-TYPE    
  IpAddress  

accessibleIpStatus 1.3.6.1.4.1.8691.7.69.1.30.2.1.3
The status is active to indicate normal. Use createAndGo to create new on multiple SET. Use createAndWait to create new on one SET all then actvie. Use destroy to delete this row.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4), createAndWait(5), destroy(6)  

sysFileUpdate 1.3.6.1.4.1.8691.7.69.1.31
OBJECT IDENTIFIER    

tftpServer 1.3.6.1.4.1.8691.7.69.1.31.1
The TFTP Server name(IP Address)
OBJECT-TYPE    
  DisplayString  

firmwarePathName 1.3.6.1.4.1.8691.7.69.1.31.2
The path name of firmware file in the TFTP Server
OBJECT-TYPE    
  DisplayString  

logPathName 1.3.6.1.4.1.8691.7.69.1.31.3
The path name of log file in the TFTP Server
OBJECT-TYPE    
  DisplayString  

confPathName 1.3.6.1.4.1.8691.7.69.1.31.4
The path name of configuration file in the TFTP Server
OBJECT-TYPE    
  DisplayString  

tftpUpdate 1.3.6.1.4.1.8691.7.69.1.31.5
Tok_String
OBJECT-TYPE    
  INTEGER importFirmware(1), importConfig(2), exportConfig(3), exportLog(4)  

timeSetting 1.3.6.1.4.1.8691.7.69.1.32
OBJECT IDENTIFIER    

sysDateTime 1.3.6.1.4.1.8691.7.69.1.32.1
The date time of system
OBJECT-TYPE    
  DateAndTime  

calibratePeriod 1.3.6.1.4.1.8691.7.69.1.32.2
The period (seconds) that calibrate with time server
OBJECT-TYPE    
  INTEGER  

timeServer1 1.3.6.1.4.1.8691.7.69.1.32.3
The first time server
OBJECT-TYPE    
  DisplayString  

timeServer2 1.3.6.1.4.1.8691.7.69.1.32.4
The second time server
OBJECT-TYPE    
  DisplayString  

daylightSaving 1.3.6.1.4.1.8691.7.69.1.32.5
OBJECT IDENTIFIER    

startMonth 1.3.6.1.4.1.8691.7.69.1.32.5.1
Setting Start Month of Daylight Saving time
OBJECT-TYPE    
  INTEGER na(0), jan(1), feb(2), mar(3), apr(4), may(5), jun(6), jul(7), aug(8), sep(9), oct(10), nov(11), dec(12)  

startWeek 1.3.6.1.4.1.8691.7.69.1.32.5.2
Setting Start Week of Daylight Saving time
OBJECT-TYPE    
  INTEGER na(0), week1(1), week2(2), week3(3), week4(4), weeklast(6)  

startDay 1.3.6.1.4.1.8691.7.69.1.32.5.3
Setting Start Day of Daylight Saving time
OBJECT-TYPE    
  INTEGER na(0), sun(1), mon(2), tue(3), wed(4), thu(5), fri(6), sat(7)  

startHour 1.3.6.1.4.1.8691.7.69.1.32.5.4
Setting Start Hour of Daylight Saving time
OBJECT-TYPE    
  INTEGER  

endMonth 1.3.6.1.4.1.8691.7.69.1.32.5.5
Setting End Month of Daylight Saving time
OBJECT-TYPE    
  INTEGER na(0), jan(1), feb(2), mar(3), apr(4), may(5), jun(6), jul(7), aug(8), sep(9), oct(10), nov(11), dec(12)  

endWeek 1.3.6.1.4.1.8691.7.69.1.32.5.6
Setting End Week of Daylight Saving time
OBJECT-TYPE    
  INTEGER na(0), week1(1), week2(2), week3(3), week4(4), weeklast(6)  

endDay 1.3.6.1.4.1.8691.7.69.1.32.5.7
Setting End Day of Daylight Saving time
OBJECT-TYPE    
  INTEGER na(0), sun(1), mon(2), tue(3), wed(4), thu(5), fri(6), sat(7)  

endHour 1.3.6.1.4.1.8691.7.69.1.32.5.8
Setting End Hour of Daylight Saving time
OBJECT-TYPE    
  INTEGER  

offsetHours 1.3.6.1.4.1.8691.7.69.1.32.5.9
Setting Offset Hours of Daylight Saving time
OBJECT-TYPE    
  INTEGER  

enableNTPServer 1.3.6.1.4.1.8691.7.69.1.32.6
This enable NTP Server.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

clockSource 1.3.6.1.4.1.8691.7.69.1.32.7
The clock source of system
OBJECT-TYPE    
  INTEGER local(0), sntp(1), ntp(2)  

ntpAuthenticate 1.3.6.1.4.1.8691.7.69.1.32.8
NTP authentication
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

ntpPeerTable 1.3.6.1.4.1.8691.7.69.1.32.9
NTP peer table
OBJECT-TYPE    
  SEQUENCE OF  
    NtpPeerEntry

ntpPeerEntry 1.3.6.1.4.1.8691.7.69.1.32.9.1
NTP peer settings
OBJECT-TYPE    
  NtpPeerEntry  

ntpPeerIndex 1.3.6.1.4.1.8691.7.69.1.32.9.1.1
NTP peer index
OBJECT-TYPE    
  INTEGER  

ntpPeerAddress 1.3.6.1.4.1.8691.7.69.1.32.9.1.2
NTP peer address
OBJECT-TYPE    
  DisplayString  

ntpPeerAuthenticate 1.3.6.1.4.1.8691.7.69.1.32.9.1.3
NTP authentication
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

ntpPeerAuthenticateKeyid 1.3.6.1.4.1.8691.7.69.1.32.9.1.4
NTP authentication key Id
OBJECT-TYPE    
  INTEGER  

ntpAuthenticateKeyTable 1.3.6.1.4.1.8691.7.69.1.32.10
NTP authenticate key table
OBJECT-TYPE    
  SEQUENCE OF  
    NtpAuthenticateKeyEntry

ntpAuthenticateKeyEntry 1.3.6.1.4.1.8691.7.69.1.32.10.1
NTP authenticate key settings
OBJECT-TYPE    
  NtpAuthenticateKeyEntry  

ntpAuthenticateKeyIndex 1.3.6.1.4.1.8691.7.69.1.32.10.1.1
NTP authenticate key index
OBJECT-TYPE    
  INTEGER  

ntpAuthenticateKeyID 1.3.6.1.4.1.8691.7.69.1.32.10.1.2
NTP authenticate key id
OBJECT-TYPE    
  INTEGER  

ntpAuthenticateKeyString 1.3.6.1.4.1.8691.7.69.1.32.10.1.3
NTP authenticate key string
OBJECT-TYPE    
  DisplayString  

ntpAuthenticateKeyTrusted 1.3.6.1.4.1.8691.7.69.1.32.10.1.4
NTP authenticate key trusted
OBJECT-TYPE    
  INTEGER distrust(0), trusted(1)  

dipSwitchSetting 1.3.6.1.4.1.8691.7.69.1.34
OBJECT IDENTIFIER    

dipSwitchEnableTurboRing 1.3.6.1.4.1.8691.7.69.1.34.1
Enable TurboRing Dip Switch functions
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

dipSwitchTurboRingPole 1.3.6.1.4.1.8691.7.69.1.34.2
The TurboRing Pole status of Dip switch.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

dipSwitchRingCouplingPole 1.3.6.1.4.1.8691.7.69.1.34.3
The Ring Coupling Pole status of Dip switch.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

dipSwitchRingMasterPole 1.3.6.1.4.1.8691.7.69.1.34.4
The Ring Master Pole status of Dip switch.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

backupMediaSetting 1.3.6.1.4.1.8691.7.69.1.35
OBJECT IDENTIFIER    

abc02Status 1.3.6.1.4.1.8691.7.69.1.35.2
Current status of ABC-02
OBJECT-TYPE    
  INTEGER device-not-present(0), unauthorized-media(1), detecting(2), working(3), ready-and-removable(4)  

abc02AutoImportConfig 1.3.6.1.4.1.8691.7.69.1.35.3
Auto load configuration from ABC to system when boot up
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

abc02AutoExportConfig 1.3.6.1.4.1.8691.7.69.1.35.4
Auto backup to ABC-02 when configuration change
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

abc02AutoExportLog 1.3.6.1.4.1.8691.7.69.1.35.5
Auto backup of event log to prevent overwrite
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

enableWarmStart 1.3.6.1.4.1.8691.7.69.1.36
Enable to restart MOXA ethernet switch.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

syslogSetting 1.3.6.1.4.1.8691.7.69.1.37
OBJECT IDENTIFIER    

syslogServer1 1.3.6.1.4.1.8691.7.69.1.37.1
The syslog server 1
OBJECT-TYPE    
  DisplayString  

syslogServer1port 1.3.6.1.4.1.8691.7.69.1.37.2
The syslog server 1 port
OBJECT-TYPE    
  INTEGER  

syslogServer2 1.3.6.1.4.1.8691.7.69.1.37.3
The syslog server 2
OBJECT-TYPE    
  DisplayString  

syslogServer2port 1.3.6.1.4.1.8691.7.69.1.37.4
The syslog server 2 port
OBJECT-TYPE    
  INTEGER  

syslogServer3 1.3.6.1.4.1.8691.7.69.1.37.5
The syslog server 3
OBJECT-TYPE    
  DisplayString  

syslogServer3port 1.3.6.1.4.1.8691.7.69.1.37.6
The syslog server 3 port
OBJECT-TYPE    
  INTEGER  

dhcpRelayAgentSetting 1.3.6.1.4.1.8691.7.69.1.39
OBJECT IDENTIFIER    

dhcpServer1 1.3.6.1.4.1.8691.7.69.1.39.1
The dhcp Relay Agent Server 1.
OBJECT-TYPE    
  DisplayString  

dhcpServer2 1.3.6.1.4.1.8691.7.69.1.39.2
The dhcp Relay Agent Server 2.
OBJECT-TYPE    
  DisplayString  

dhcpServer3 1.3.6.1.4.1.8691.7.69.1.39.3
The dhcp Relay Agent Server 3.
OBJECT-TYPE    
  DisplayString  

dhcpServer4 1.3.6.1.4.1.8691.7.69.1.39.4
The dhcp Relay Agent Server 4.
OBJECT-TYPE    
  DisplayString  

option82Setting 1.3.6.1.4.1.8691.7.69.1.39.5
OBJECT IDENTIFIER    

enableOption82 1.3.6.1.4.1.8691.7.69.1.39.5.1
Enable DHCP Option 82
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

option82Type 1.3.6.1.4.1.8691.7.69.1.39.5.2
Option 82 Type selector
OBJECT-TYPE    
  INTEGER ip(0), mac(1), client-id(2), other(3)  

option82Value 1.3.6.1.4.1.8691.7.69.1.39.5.3
Option 82 Type Value
OBJECT-TYPE    
  DisplayString  

option82ValueDisplay 1.3.6.1.4.1.8691.7.69.1.39.5.4
Option 82 Type Value Display
OBJECT-TYPE    
  DisplayString  

dhcpFunctionTable 1.3.6.1.4.1.8691.7.69.1.39.6
DHCP Function Table.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpFunctionEntry

dhcpFunctionEntry 1.3.6.1.4.1.8691.7.69.1.39.6.1
DHCP Function Table Entry.
OBJECT-TYPE    
  DhcpFunctionEntry  

dhcpPortIndex 1.3.6.1.4.1.8691.7.69.1.39.6.1.1
The DHCP Port Index.
OBJECT-TYPE    
  INTEGER  

circuitID 1.3.6.1.4.1.8691.7.69.1.39.6.1.2
The Circuit ID.
OBJECT-TYPE    
  DisplayString  

option82Enable 1.3.6.1.4.1.8691.7.69.1.39.6.1.3
This enable option 82 of the port.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

ieee1588Setting 1.3.6.1.4.1.8691.7.69.1.41
OBJECT IDENTIFIER    

ptpv1Setting 1.3.6.1.4.1.8691.7.69.1.41.1
OBJECT IDENTIFIER    

enablePtpv1 1.3.6.1.4.1.8691.7.69.1.41.1.1
This enable the PTP functon.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

clockModev1 1.3.6.1.4.1.8691.7.69.1.41.1.2
the clock mode of the PTP clock.
OBJECT-TYPE    
  INTEGER v1BC(0), v2E2E2stepTC(1), v2P2PTC(3), v2E2EBC(4), v2P2PBC(5)  

syncIntervalv1 1.3.6.1.4.1.8691.7.69.1.41.1.3
the logSyncInterval of the PTP clock.
OBJECT-TYPE    
  INTEGER oneSec(0), twoSec(1), fourSec(2), eightSec(3), sixteenSec(4)  

subDomainNamev1 1.3.6.1.4.1.8691.7.69.1.41.1.4
The subdomain name of the PTP clock.
OBJECT-TYPE    
  INTEGER dflt(0), alt1(1), alt2(2), alt3(3)  

preferMasterv1 1.3.6.1.4.1.8691.7.69.1.41.1.5
This enable the PTP prefer master function.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

ptpv2Setting 1.3.6.1.4.1.8691.7.69.1.41.2
OBJECT IDENTIFIER    

enablePtp 1.3.6.1.4.1.8691.7.69.1.41.2.1
This enable the PTP functon.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

clockMode 1.3.6.1.4.1.8691.7.69.1.41.2.2
the clock mode of the PTP clock.
OBJECT-TYPE    
  INTEGER v1BC(0), v2E2E2stepTC(1), v2P2PTC(3), v2E2EBC(4), v2P2PBC(5)  

transport 1.3.6.1.4.1.8691.7.69.1.41.2.3
the transport mode of the PTP clock.
OBJECT-TYPE    
  INTEGER ieee802dot3(0), ipv4(1)  

syncInterval 1.3.6.1.4.1.8691.7.69.1.41.2.4
the logSyncInterval of the PTP clock.
OBJECT-TYPE    
  INTEGER t128msec(-3), t256msec(-2), t512msec(-1), t1sec(0), t2sec(1)  

logMinDelayReqInterval 1.3.6.1.4.1.8691.7.69.1.41.2.5
the logMinDelayReqInterval of the PTP clock.
OBJECT-TYPE    
  INTEGER t1sec(0), t2sec(1), t4sec(2), t8sec(3), t16sec(4), t32sec(5)  

logMinPdelayReqInterval 1.3.6.1.4.1.8691.7.69.1.41.2.6
the logMinPdelayReqInterval of the PTP clock.
OBJECT-TYPE    
  INTEGER t512msec(-1), t1sec(0), t2sec(1), t4sec(2), t8sec(3), t16sec(4), t32sec(5)  

logAnnounceInterval 1.3.6.1.4.1.8691.7.69.1.41.2.7
the logAnnounceInterval of the PTP clock.
OBJECT-TYPE    
  INTEGER t1sec(0), t2sec(1), t4sec(2), t8sec(3), t16sec(4)  

announceReceiptTimeout 1.3.6.1.4.1.8691.7.69.1.41.2.8
the announceReceiptTimeout of the PTP clock.
OBJECT-TYPE    
  INTEGER 2..10  

priority1 1.3.6.1.4.1.8691.7.69.1.41.2.9
the priority1 of the PTP clock.
OBJECT-TYPE    
  INTEGER  

priority2 1.3.6.1.4.1.8691.7.69.1.41.2.10
the priority2 of the PTP clock.
OBJECT-TYPE    
  INTEGER  

clockClass 1.3.6.1.4.1.8691.7.69.1.41.2.11
the clockClass of the PTP clock.
OBJECT-TYPE    
  INTEGER  

domainNumber 1.3.6.1.4.1.8691.7.69.1.41.2.12
The domain number of the PTP clock.
OBJECT-TYPE    
  INTEGER dflt(0), alt1(1), alt2(2), alt3(3)  

localUtcOffset 1.3.6.1.4.1.8691.7.69.1.41.2.13
the UTC offset of the local PTP clock.
OBJECT-TYPE    
  INTEGER  

localUtcOffsetValid 1.3.6.1.4.1.8691.7.69.1.41.2.14
the UTC offset valid of the local PTP clock.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

localLeap59 1.3.6.1.4.1.8691.7.69.1.41.2.15
the leap59 of the local PTP clock.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

localLeap61 1.3.6.1.4.1.8691.7.69.1.41.2.16
the leap61 of the local PTP clock.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

localPtpTimescale 1.3.6.1.4.1.8691.7.69.1.41.2.17
the timescale of the local PTP clock.
OBJECT-TYPE    
  INTEGER arb(0), ptp(1)  

localArbTime 1.3.6.1.4.1.8691.7.69.1.41.2.18
the ARB time of the local PTP clock.
OBJECT-TYPE    
  INTEGER  

ptpv1Status 1.3.6.1.4.1.8691.7.69.1.41.3
OBJECT IDENTIFIER    

offsetToMasterv1 1.3.6.1.4.1.8691.7.69.1.41.3.1
The offset to master for nsec.
OBJECT-TYPE    
  INTEGER  

meanPathDelayv1 1.3.6.1.4.1.8691.7.69.1.41.3.2
The mean path delay of the PTP clock.
OBJECT-TYPE    
  INTEGER  

grandMasterUuidv1 1.3.6.1.4.1.8691.7.69.1.41.3.3
The grand master UUID address of the PTP clock.
OBJECT-TYPE    
  MacAddress  

parentUuidv1 1.3.6.1.4.1.8691.7.69.1.41.3.4
The parent master UUID address of the PTP clock.
OBJECT-TYPE    
  MacAddress  

clockStratumv1 1.3.6.1.4.1.8691.7.69.1.41.3.5
The clock stratum of the PTP clock.
OBJECT-TYPE    
  INTEGER  

clockIdentifierv1 1.3.6.1.4.1.8691.7.69.1.41.3.6
The clock identifier of the PTP clock.
OBJECT-TYPE    
  DisplayString  

ptpv2Status 1.3.6.1.4.1.8691.7.69.1.41.4
OBJECT IDENTIFIER    

offsetToMaster 1.3.6.1.4.1.8691.7.69.1.41.4.1
The offset to master for nsec.
OBJECT-TYPE    
  INTEGER  

meanPathDelay 1.3.6.1.4.1.8691.7.69.1.41.4.2
The mean path delay of the PTP clock.
OBJECT-TYPE    
  INTEGER  

parentIdentity 1.3.6.1.4.1.8691.7.69.1.41.4.3
The parent identity of the PTP clock.
OBJECT-TYPE    
  DisplayString  

grandmasterIdentity 1.3.6.1.4.1.8691.7.69.1.41.4.4
The grandmaster identity of the PTP clock.
OBJECT-TYPE    
  DisplayString  

grandmasterClockClass 1.3.6.1.4.1.8691.7.69.1.41.4.5
The grandmaster clockClass of the PTP clock.
OBJECT-TYPE    
  INTEGER  

grandmasterClockAccuracy 1.3.6.1.4.1.8691.7.69.1.41.4.6
The grandmaster clockAccuracy of the PTP clock.
OBJECT-TYPE    
  INTEGER  

grandmasterPriority1 1.3.6.1.4.1.8691.7.69.1.41.4.7
The grandmaster priority1 of the PTP clock.
OBJECT-TYPE    
  INTEGER  

grandmasterPriority2 1.3.6.1.4.1.8691.7.69.1.41.4.8
The grandmaster priority2 of the PTP clock.
OBJECT-TYPE    
  INTEGER  

stepsRemoved 1.3.6.1.4.1.8691.7.69.1.41.4.9
The steps removed of the PTP clock.
OBJECT-TYPE    
  INTEGER  

currentUtcOffset 1.3.6.1.4.1.8691.7.69.1.41.4.10
The current utc offset of the PTP clock.
OBJECT-TYPE    
  INTEGER  

currentUtcOffsetValid 1.3.6.1.4.1.8691.7.69.1.41.4.11
The current utc offset valid flag of the PTP clock.
OBJECT-TYPE    
  DisplayString  

leap59 1.3.6.1.4.1.8691.7.69.1.41.4.12
The leap59 of the PTP clock.
OBJECT-TYPE    
  DisplayString  

leap61 1.3.6.1.4.1.8691.7.69.1.41.4.13
The leap61 of the PTP clock.
OBJECT-TYPE    
  DisplayString  

ptpTimescale 1.3.6.1.4.1.8691.7.69.1.41.4.14
The ptp timescale of the PTP clock.
OBJECT-TYPE    
  DisplayString  

timesource 1.3.6.1.4.1.8691.7.69.1.41.4.15
The timesource of the PTP clock.
OBJECT-TYPE    
  DisplayString  

ptpPortTable 1.3.6.1.4.1.8691.7.69.1.41.5
The ptp port table.
OBJECT-TYPE    
  SEQUENCE OF  
    PtpPortEntry

ptpPortEntry 1.3.6.1.4.1.8691.7.69.1.41.5.1
The ptp port entry.
OBJECT-TYPE    
  PtpPortEntry  

ptpPortIndex 1.3.6.1.4.1.8691.7.69.1.41.5.1.1
The ptp port index.
OBJECT-TYPE    
  INTEGER  

ptpPortEnable 1.3.6.1.4.1.8691.7.69.1.41.5.1.2
This enable the ptp port.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

ptpPortStatus 1.3.6.1.4.1.8691.7.69.1.41.5.1.3
This port status of the PTP clock.
OBJECT-TYPE    
  INTEGER ptpInitializing(0), ptpFaulty(1), ptpDisabled(2), ptpListening(3), ptpPreMaster(4), ptpMaster(5), ptpPassive(6), ptpUncalibrated(7), ptpSlave(8)  

mibNotificationsPrefix 1.3.6.1.4.1.8691.7.69.0
OBJECT IDENTIFIER    

varconfigChangeTrap 1.3.6.1.4.1.8691.7.69.2.1
The configuration has been changed.
OBJECT-TYPE    
  INTEGER none(1), configChanged(2)  

configChangeTrap 1.3.6.1.4.1.8691.7.69.0.1
The configuration has been changed.
NOTIFICATION-TYPE    

varpower1Trap 1.3.6.1.4.1.8691.7.69.2.2
The power on/off changed.
OBJECT-TYPE    
  INTEGER none(1), on2off(2), off2on(3)  

power1Trap 1.3.6.1.4.1.8691.7.69.0.2
The power on/off changed.
NOTIFICATION-TYPE    

varpower2Trap 1.3.6.1.4.1.8691.7.69.2.3
The power on/off changed.
OBJECT-TYPE    
  INTEGER none(1), on2off(2), off2on(3)  

power2Trap 1.3.6.1.4.1.8691.7.69.0.3
The power on/off changed.
NOTIFICATION-TYPE    

vartrafficOverloadTrap 1.3.6.1.4.1.8691.7.69.2.4
The ethernet port's traffic loading exceeds the pre-defined value.
OBJECT-TYPE    
  INTEGER  

trafficOverloadTrap 1.3.6.1.4.1.8691.7.69.0.4
The ethernet port's traffic loading exceeds the pre-defined value.
NOTIFICATION-TYPE    

varredundancyTopologyChangedTrap 1.3.6.1.4.1.8691.7.69.2.5
The redundancy topology has been changed.
OBJECT-TYPE    
  INTEGER none(1), topologyChanged(2), topologyChangedTurboChainHead(3), topologyChangedTurboChainTail(4)  

redundancyTopologyChangedTrap 1.3.6.1.4.1.8691.7.69.0.5
The redundancy topology has been changed.
NOTIFICATION-TYPE    

varturboRingCouplingPortChangedTrap 1.3.6.1.4.1.8691.7.69.2.6
The coupling path of Turbo Ring has been changed.
OBJECT-TYPE    
  INTEGER none(1), couplingPortChanged(2)  

turboRingCouplingPortChangedTrap 1.3.6.1.4.1.8691.7.69.0.6
The coupling path of Turbo Ring has been changed.
NOTIFICATION-TYPE    

varturboRingMasterChangedTrap 1.3.6.1.4.1.8691.7.69.2.7
The master of Turbo Ring has been changed.
OBJECT-TYPE    
  INTEGER none(1), ringMasterChanged(2)  

turboRingMasterChangedTrap 1.3.6.1.4.1.8691.7.69.0.7
The master of Turbo Ring has been changed.
NOTIFICATION-TYPE    

varturboRingMasterMismatchTrap 1.3.6.1.4.1.8691.7.69.2.22
The master of Turbo Ring has been mismatch.
OBJECT-TYPE    
  INTEGER none(1), ringMasterMismatch(2)  

turboRingMasterMismatchTrap 1.3.6.1.4.1.8691.7.69.0.22
The master of Turbo Ring has been mismatch.
NOTIFICATION-TYPE    

varPortLoopDetectedTrap 1.3.6.1.4.1.8691.7.69.2.17
The DUT port is looping.
OBJECT-TYPE    
  INTEGER  

portLoopDetectedTrap 1.3.6.1.4.1.8691.7.69.0.17
The DUT port is looping.
NOTIFICATION-TYPE    

varRateLimitedOnTrap 1.3.6.1.4.1.8691.7.69.2.18
The DUT port is rate limit.
OBJECT-TYPE    
  INTEGER none(1), rateLimitON(2), rateLimitOFF(3)  

rateLimitedOnTrap 1.3.6.1.4.1.8691.7.69.0.18
The DUT port rate limit is ON.
NOTIFICATION-TYPE    

varLLDPChgTrap 1.3.6.1.4.1.8691.7.69.2.19
The LLDP table is changing.
OBJECT-TYPE    
  INTEGER  

lldpChgTrap 1.3.6.1.4.1.8691.7.69.0.19
The LLDP table is changing.
NOTIFICATION-TYPE    

varABC02WarningTrap 1.3.6.1.4.1.8691.7.69.2.20
Warning trap while specific error is occured in abc02.
OBJECT-TYPE    
  INTEGER noEnoughSpace(1), nnauthorizedMediaIsDetected(2), exportConfigurationFail(3), exportLogFail(4), autoImportConfigurationFail(5)  

abc02WarningTrap 1.3.6.1.4.1.8691.7.69.0.20
Warning trap while specific error is occured in abc02.
NOTIFICATION-TYPE    

varUserAuthSuccessTrap 1.3.6.1.4.1.8691.7.69.2.24
Account authentication success.
OBJECT-TYPE    
  OCTET STRING  

userAuthSuccessTrap 1.3.6.1.4.1.8691.7.69.0.24
Account authentication success.
NOTIFICATION-TYPE    

varUserAuthFailTrap 1.3.6.1.4.1.8691.7.69.2.25
Account authentication failed.
OBJECT-TYPE    
  OCTET STRING  

userAuthFailTrap 1.3.6.1.4.1.8691.7.69.0.25
Account authentication failed.
NOTIFICATION-TYPE    

varMacStickyPortViolationPortDisableTrap 1.3.6.1.4.1.8691.7.69.2.26
The number of sticky Mac address on the port was over the limit. A macStickyPortViolationPortDisableTrap will contain 3 elements: port, macaddr, and vlanid.
OBJECT-TYPE    
  INTEGER none(1), violationPortDisable(2)  

macStickyPortViolationPortDisableTrap 1.3.6.1.4.1.8691.7.69.0.26
The number of sticky Mac address on the port was over the limit. A macStickyPortViolationPortDisableTrap will contain 3 elements: port, macaddr, and vlanid.
NOTIFICATION-TYPE    

varFiberWarningTrap 1.3.6.1.4.1.8691.7.69.2.28
Warning trap while fiber is over threshold.
OBJECT-TYPE    
  INTEGER  

fiberWarningTrap 1.3.6.1.4.1.8691.7.69.0.28
Warning trap while fiber is over threshold.
NOTIFICATION-TYPE    

varLoggingCapacityTrap 1.3.6.1.4.1.8691.7.69.2.29
Warning trap while event log is over capacity threshold.
OBJECT-TYPE    
  INTEGER  

loggingCapacityTrap 1.3.6.1.4.1.8691.7.69.0.29
Warning trap while event log is over capacity threshold.
NOTIFICATION-TYPE    

varUserInfoChgTrap 1.3.6.1.4.1.8691.7.69.2.31
Account information has been changed.
OBJECT-TYPE    
  OCTET STRING  

userInfoChgTrap 1.3.6.1.4.1.8691.7.69.0.31
Account information has been changed.
NOTIFICATION-TYPE    

varConfigImportTrap 1.3.6.1.4.1.8691.7.69.2.32
Configuration has been imported.
OBJECT-TYPE    
  INTEGER  

configImportTrap 1.3.6.1.4.1.8691.7.69.0.32
Configuration has been imported.
NOTIFICATION-TYPE    

varRemoteAuthSuccessTrap 1.3.6.1.4.1.8691.7.69.2.38
The login authentication is successful by the remote server
OBJECT-TYPE    
  INTEGER tacacs(1), radius(2)  

remoteAuthSuccessTrap 1.3.6.1.4.1.8691.7.69.0.38
The login authentication is successful by the remote server
NOTIFICATION-TYPE    

varRemoteAuthFailTrap 1.3.6.1.4.1.8691.7.69.2.39
The login authentication is failed by the remote server
OBJECT-TYPE    
  INTEGER tacacs(1), radius(2)  

remoteAuthFailTrap 1.3.6.1.4.1.8691.7.69.0.39
The login authentication is failed by the remote server
NOTIFICATION-TYPE    

diagnosis 1.3.6.1.4.1.8691.7.69.1.42
OBJECT IDENTIFIER    

lldpSetting 1.3.6.1.4.1.8691.7.69.1.42.1
OBJECT IDENTIFIER    

enableLLDP 1.3.6.1.4.1.8691.7.69.1.42.1.1
This enable the LLDP functon.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpMSGInterval 1.3.6.1.4.1.8691.7.69.1.42.1.2
The LLDP message transmit interval.
OBJECT-TYPE    
  INTEGER  

industrialProtocol 1.3.6.1.4.1.8691.7.69.1.47
OBJECT IDENTIFIER    

eipSetting 1.3.6.1.4.1.8691.7.69.1.47.1
OBJECT IDENTIFIER    

modbusSetting 1.3.6.1.4.1.8691.7.69.1.47.2
OBJECT IDENTIFIER    

profinetioSetting 1.3.6.1.4.1.8691.7.69.1.47.3
OBJECT IDENTIFIER    

enableEtherNetIP 1.3.6.1.4.1.8691.7.69.1.47.1.1
This enable the EtherNet/IP functon.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

enableModbus 1.3.6.1.4.1.8691.7.69.1.47.2.1
This enable the Modbus functon.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

enableProfinetIO 1.3.6.1.4.1.8691.7.69.1.47.3.1
This enable the PROFINET IO functon.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

garpSetting 1.3.6.1.4.1.8691.7.69.1.45
OBJECT IDENTIFIER    

leaveAllTime 1.3.6.1.4.1.8691.7.69.1.45.3
Leaveall Time (ms).
OBJECT-TYPE    
  INTEGER  

leaveTime 1.3.6.1.4.1.8691.7.69.1.45.2
Leave Time (ms).
OBJECT-TYPE    
  INTEGER  

joinTime 1.3.6.1.4.1.8691.7.69.1.45.1
Join Time (ms).
OBJECT-TYPE    
  INTEGER  

enableFactoryDefault 1.3.6.1.4.1.8691.7.69.1.48
Reset all EtherDevice switch settings to factory default values
OBJECT-TYPE    
  INTEGER activate(1)  

eventlog 1.3.6.1.4.1.8691.7.69.1.46
OBJECT IDENTIFIER    

eventlogTable 1.3.6.1.4.1.8691.7.69.1.46.1
The table of eventlog.
OBJECT-TYPE    
  SEQUENCE OF  
    EventlogEntry

eventlogEntry 1.3.6.1.4.1.8691.7.69.1.46.1.1
The table entry of eventlog.
OBJECT-TYPE    
  EventlogEntry  

eventlogIndex 1.3.6.1.4.1.8691.7.69.1.46.1.1.1
The index of eventlog entry.
OBJECT-TYPE    
  INTEGER  

eventlogBootup 1.3.6.1.4.1.8691.7.69.1.46.1.1.2
The reboot count of the system.
OBJECT-TYPE    
  INTEGER  

eventlogDate 1.3.6.1.4.1.8691.7.69.1.46.1.1.3
The date of the event occured.
OBJECT-TYPE    
  DisplayString  

eventlogTime 1.3.6.1.4.1.8691.7.69.1.46.1.1.4
The time of the event occured.
OBJECT-TYPE    
  DisplayString  

eventlogUptime 1.3.6.1.4.1.8691.7.69.1.46.1.1.5
The time of the event occured after booting up.
OBJECT-TYPE    
  DisplayString  

eventlogEvent 1.3.6.1.4.1.8691.7.69.1.46.1.1.6
The event which occured in the system.
OBJECT-TYPE    
  DisplayString  

eventlogClear 1.3.6.1.4.1.8691.7.69.1.46.2
To clear the eventlog, set value 1 to this field.
OBJECT-TYPE    
  INTEGER noop(0), clear(1)  

accessControlList 1.3.6.1.4.1.8691.7.69.1.52
OBJECT IDENTIFIER    

accessControlTable 1.3.6.1.4.1.8691.7.69.1.52.1
The table of ACL rule settings. This table is used to configure ACL rules.
OBJECT-TYPE    
  SEQUENCE OF  
    AccessControlEntry

accessControlEntry 1.3.6.1.4.1.8691.7.69.1.52.1.1
The entry information of ACL table.
OBJECT-TYPE    
  AccessControlEntry  

aclRuleIndex 1.3.6.1.4.1.8691.7.69.1.52.1.1.1
The index of the ACL rule.
OBJECT-TYPE    
  INTEGER  

listID 1.3.6.1.4.1.8691.7.69.1.52.1.1.2
The listID of the ACL rule.
OBJECT-TYPE    
  INTEGER  

filterType 1.3.6.1.4.1.8691.7.69.1.52.1.1.3
The type of the ACL filter.
OBJECT-TYPE    
  INTEGER ipBase(0), macBase(1)  

actionFlag 1.3.6.1.4.1.8691.7.69.1.52.1.1.4
The action of the ACL rule.
OBJECT-TYPE    
  INTEGER permit(0), deny(1)  

srcMacAddr 1.3.6.1.4.1.8691.7.69.1.52.1.1.5
The source MAC address of the ACL rule.
OBJECT-TYPE    
  MacAddress  

srcMacMask 1.3.6.1.4.1.8691.7.69.1.52.1.1.6
The mask of the source MAC address in the ACL rule.
OBJECT-TYPE    
  MacAddress  

dstMacAddr 1.3.6.1.4.1.8691.7.69.1.52.1.1.7
The destination MAC address of the ACL rule.
OBJECT-TYPE    
  MacAddress  

dstMacMask 1.3.6.1.4.1.8691.7.69.1.52.1.1.8
The mask of the destination MAC address in the ACL rule.
OBJECT-TYPE    
  MacAddress  

etherType 1.3.6.1.4.1.8691.7.69.1.52.1.1.9
The ether type of the ACL rule. This setting will apply to both ARP and RARP traffic stream due to hardware platform design ! ! ! Because of hardware platform limitations, when Ether type ARP is selected the switch will not be able to filter packets by specific destination address ! ! !
OBJECT-TYPE    
  INTEGER  

vlanID 1.3.6.1.4.1.8691.7.69.1.52.1.1.10
The VLAN ID of the ACL rule.
OBJECT-TYPE    
  INTEGER 1..4094  

srcIpAddr 1.3.6.1.4.1.8691.7.69.1.52.1.1.11
The source IP address of the ACL rule.
OBJECT-TYPE    
  IpAddress  

srcNetmask 1.3.6.1.4.1.8691.7.69.1.52.1.1.12
The source IP address's mask of the ACL rule.
OBJECT-TYPE    
  IpAddress  

dstIpAddr 1.3.6.1.4.1.8691.7.69.1.52.1.1.13
The destination IP address of the ACL rule
OBJECT-TYPE    
  IpAddress  

dstNetmask 1.3.6.1.4.1.8691.7.69.1.52.1.1.14
The destination IP address's mask of the ACL rule.
OBJECT-TYPE    
  IpAddress  

protocolCode 1.3.6.1.4.1.8691.7.69.1.52.1.1.15
The protocol code of the ACL rule.
OBJECT-TYPE    
  INTEGER  

srcsocketPort 1.3.6.1.4.1.8691.7.69.1.52.1.1.16
The source UDP/TCP port of the ACL rule.
OBJECT-TYPE    
  INTEGER  

dstsocketPort 1.3.6.1.4.1.8691.7.69.1.52.1.1.17
The destination UDP/TCP port of the ACL rule.
OBJECT-TYPE    
  INTEGER  

aclStatus 1.3.6.1.4.1.8691.7.69.1.52.1.1.18
The status is active to indicate normal. Use createAndGo to create new on multiple SET. Use createAndWait to create new on one SET all then actvie. Use destroy to delete this row.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4), createAndWait(5), destroy(6)  

aclAttachmentTable 1.3.6.1.4.1.8691.7.69.1.52.2
The table of ACL attachment settings. This table is used to configure ACL attachment port and list name.
OBJECT-TYPE    
  SEQUENCE OF  
    AclAttachmentEntry

aclAttachmentEntry 1.3.6.1.4.1.8691.7.69.1.52.2.1
The entry information of ACL attachment table.
OBJECT-TYPE    
  AclAttachmentEntry  

aclID 1.3.6.1.4.1.8691.7.69.1.52.2.1.1
The listID of the ACL attachment entry.
OBJECT-TYPE    
  INTEGER  

ingressPort 1.3.6.1.4.1.8691.7.69.1.52.2.1.2
The ingress ports of the ACL attachment entry.
OBJECT-TYPE    
  PortList  

aclListName 1.3.6.1.4.1.8691.7.69.1.52.2.1.4
The ACL entry name.
OBJECT-TYPE    
  DisplayString  

cpuLoading5s 1.3.6.1.4.1.8691.7.69.1.53
CPU Loading for the past 5 seconds in %.
OBJECT-TYPE    
  INTEGER  

cpuLoading30s 1.3.6.1.4.1.8691.7.69.1.54
CPU Loading for the past 30 seconds in %.
OBJECT-TYPE    
  INTEGER  

cpuLoading300s 1.3.6.1.4.1.8691.7.69.1.55
CPU Loading for the past 5 minutes in %.
OBJECT-TYPE    
  INTEGER  

totalMemory 1.3.6.1.4.1.8691.7.69.1.56
Total size of System RAM.
OBJECT-TYPE    
  INTEGER  

freeMemory 1.3.6.1.4.1.8691.7.69.1.57
Total size of free dynamic memory
OBJECT-TYPE    
  INTEGER  

usedMemory 1.3.6.1.4.1.8691.7.69.1.58
Total size of used dynamic memory
OBJECT-TYPE    
  INTEGER  

memoryUsage 1.3.6.1.4.1.8691.7.69.1.59
The usage of memory size in %.
OBJECT-TYPE    
  INTEGER  

ivlSwitch 1.3.6.1.4.1.8691.7.69.1.76
Current switch runs IVL(Independent Vlan Learning) or SVL(Shared Vlan Learning)
OBJECT-TYPE    
  INTEGER svl(0), ivl(1)  

supportMacSticky 1.3.6.1.4.1.8691.7.69.1.77
Support MAC Sticky feature or not.
OBJECT-TYPE    
  INTEGER not-support(0), support(1)  

loopProtection 1.3.6.1.4.1.8691.7.69.1.61
This enable the Loop Protection functon.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

eventSettings 1.3.6.1.4.1.8691.7.69.1.62
OBJECT IDENTIFIER    

systemEventSettingsTable 1.3.6.1.4.1.8691.7.69.1.62.1
The system event settings table.
OBJECT-TYPE    
  SEQUENCE OF  
    SystemEventSettingsEntry

systemEventSettingsEntry 1.3.6.1.4.1.8691.7.69.1.62.1.1
System Event Settings Entry.
OBJECT-TYPE    
  SystemEventSettingsEntry  

systemEventIndex 1.3.6.1.4.1.8691.7.69.1.62.1.1.1
Index of system event settings
OBJECT-TYPE    
  INTEGER  

systemEventActive 1.3.6.1.4.1.8691.7.69.1.62.1.1.2
Status of active of system event settings
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

systemEventName 1.3.6.1.4.1.8691.7.69.1.62.1.1.3
Name of system event settings
OBJECT-TYPE    
  DisplayString  

systemEventSupport 1.3.6.1.4.1.8691.7.69.1.62.1.1.4
Status of support modules of system event settings.
OBJECT-TYPE    
  INTEGER none(0), support-SNMPTrap-only(1), support-Email-only(2), support-SNMP-Trap-Email(3), support-Syslog-only(4), support-SNMPTrap-Syslog(5), support-Email-Syslog(6), support-SNMPTrap-Email-Syslog(7), support-Relay1-only(8), support-SNMPTrap-Relay1(9), support-Email-Relay1(10), support-SNMPTrap-Email-Relay1(11), support-Syslog-Relay1(12), support-SNMPTrap-Syslog-Relay1(13), support-Email-Syslog-Relay1(14), support-SNMPTrap-Email-Syslog-Relay1(15), support-Relay2-only(16), support-SNMPTrap-Relay2(17), support-Email-Relay2(18), support-SNMPTrap-Email-Relay2(19), support-Syslog-Relay2(20), support-SNMPTrap-Syslog-Relay2(21), support-Email-Syslog-Relay2(22), support-SNMPTrap-Email-Syslog-Relay2(23), support-Relay1-Relay2(24), support-SNMPTrap-Relay1-Relay2(25), support-Syslog-Relay1-Relay2(28), support-Email-Syslog-Relay1-Relay2(30), support-all-SNMPTrap-Email-Syslog-Relay1-Relay2(31)  

systemEventModuleEnable 1.3.6.1.4.1.8691.7.69.1.62.1.1.5
Status of enable of system event settings.
OBJECT-TYPE    
  INTEGER none(0), enable-SNMPTrap-only(1), enable-Email-only(2), enable-SNMPTrap-Email(3), enable-Syslog-only(4), enable-SNMPTrap-Syslog(5), enable-Email-Syslog(6), enable-SNMPTrap-Email-Syslog(7), enable-Relay1-only(8), enable-SNMPTrap-Relay1(9), enable-Email-Relay1(10), enable-SNMPTrap-Email-Relay1(11), enable-Syslog-Relay1(12), enable-SNMPTrap-Syslog-Relay1(13), enable-Email-Syslog-Relay1(14), enable-SNMPTrap-Email-Syslog-Relay1(15), enable-Relay2-only(16), enable-SNMPTrap-Relay2(17), enable-Email-Relay2(18), enable-SNMPTrap-Email-Relay2(19), enable-Syslog-Relay2(20), enable-SNMPTrap-Syslog-Relay2(21), enable-Email-Syslog-Relay2(22), enable-SNMPTrap-Email-Syslog-Relay2(23), enable-Relay1-Relay2(24), enable-SNMPTrap-Relay1-Relay2(25), enable-Syslog-Relay1-Relay2(28), enable-Email-Syslog-Relay1-Relay2(30), enable-All-SNMPTrap-Email-Syslog-Relay1-Relay2(31)  

systemEventSeverity 1.3.6.1.4.1.8691.7.69.1.62.1.1.6
Severity of system event settings
OBJECT-TYPE    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), information(6), debug(7)  

portEventSettingsTable 1.3.6.1.4.1.8691.7.69.1.62.2
The port event settings table.
OBJECT-TYPE    
  SEQUENCE OF  
    PortEventSettingsEntry

portEventSettingsEntry 1.3.6.1.4.1.8691.7.69.1.62.2.1
Port Event Settings Entry.
OBJECT-TYPE    
  PortEventSettingsEntry  

portEventIndex 1.3.6.1.4.1.8691.7.69.1.62.2.1.1
Index of port event settings
OBJECT-TYPE    
  INTEGER  

portEventLabel 1.3.6.1.4.1.8691.7.69.1.62.2.1.2
Label of portEventIndex
OBJECT-TYPE    
  DisplayString  

portEventActive 1.3.6.1.4.1.8691.7.69.1.62.2.1.3
Status of active of port event settings
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

portEventEnable 1.3.6.1.4.1.8691.7.69.1.62.2.1.4
Status of event enable of port event settings
OBJECT-TYPE    
  INTEGER none(0), enable-LinkOn-only(1), enable-LinkOff-only(2), enable-LinkOn-LinkOff(3), enable-TrafficOverload-only(4), enable-LinkOn-TrafficOverload(5), enable-LinkOff-TrafficOverload(6), enable-All-LinkOn-LinkOff-TrafficOverload(7)  

portEventTrafficThreshold 1.3.6.1.4.1.8691.7.69.1.62.2.1.5
Threshold of Traffic-Overload in percentage(%)
OBJECT-TYPE    
  INTEGER 0..100  

portEventTrafficDuration 1.3.6.1.4.1.8691.7.69.1.62.2.1.6
Duration of Traffic-Overload in secs(s)
OBJECT-TYPE    
  INTEGER 1..300  

portEventModuleEnable 1.3.6.1.4.1.8691.7.69.1.62.2.1.7
Status of module enable of port event settings.
OBJECT-TYPE    
  INTEGER none(0), enable-SNMPTrap-only(1), enable-Email-only(2), enable-SNMPTrap-Email(3), enable-Syslog-only(4), enable-SNMPTrap-Syslog(5), enable-Email-Syslog(6), enable-SNMPTrap-Email-Syslog(7), enable-Relay1-only(8), enable-SNMPTrap-Relay1(9), enable-Email-Relay1(10), enable-SNMPTrap-Email-Relay1(11), enable-Syslog-Relay1(12), enable-SNMPTrap-Syslog-Relay1(13), enable-Email-Syslog-Relay1(14), enable-SNMPTrap-Email-Syslog-Relay1(15), enable-Relay2-only(16), enable-SNMPTrap-Relay2(17), enable-Email-Relay2(18), enable-SNMPTrap-Email-Relay2(19), enable-Syslog-Relay2(20), enable-SNMPTrap-Syslog-Relay2(21), enable-Email-Syslog-Relay2(22), enable-SNMPTrap-Email-Syslog-Relay2(23), enable-Relay1-Relay2(24), enable-SNMPTrap-Relay1-Relay2(25), enable-Syslog-Relay1-Relay2(28), enable-Email-Syslog-Relay1-Relay2(30), enable-All-SNMPTrap-Email-Syslog-Relay1-Relay2(31)  

portEventSeverity 1.3.6.1.4.1.8691.7.69.1.62.2.1.8
Severity of port event settings
OBJECT-TYPE    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), information(6), debug(7)  

managementInterface 1.3.6.1.4.1.8691.7.69.1.63
OBJECT IDENTIFIER    

httpEnable 1.3.6.1.4.1.8691.7.69.1.63.1
Status of http service
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

httpPort 1.3.6.1.4.1.8691.7.69.1.63.2
Port of http service
OBJECT-TYPE    
  INTEGER 1..65535  

sslEnable 1.3.6.1.4.1.8691.7.69.1.63.3
Status of ssl(https) service
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sslPort 1.3.6.1.4.1.8691.7.69.1.63.4
Port of ssl(https) service
OBJECT-TYPE    
  INTEGER 1..65535  

telnetEnable 1.3.6.1.4.1.8691.7.69.1.63.5
Status of telnet service
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

telnetPort 1.3.6.1.4.1.8691.7.69.1.63.6
Port of telnet service
OBJECT-TYPE    
  INTEGER 1..65535  

sshEnable 1.3.6.1.4.1.8691.7.69.1.63.7
Status of ssh service
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sshPort 1.3.6.1.4.1.8691.7.69.1.63.8
Port of telnet service
OBJECT-TYPE    
  INTEGER 1..65535  

mgmtInterfaceAutoLogout 1.3.6.1.4.1.8691.7.69.1.63.9
Web Timeout (Mins). Set 0 to disable
OBJECT-TYPE    
  INTEGER 0..1440  

snmpdEnable 1.3.6.1.4.1.8691.7.69.1.63.10
Status of snmp agent
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

snmpdPort 1.3.6.1.4.1.8691.7.69.1.63.11
Port of snmp agent
OBJECT-TYPE    
  INTEGER 1..65535  

moxaUtilityServiceEnable 1.3.6.1.4.1.8691.7.69.1.63.12
Status of moxa utility service
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

moxaUtilityServicePort 1.3.6.1.4.1.8691.7.69.1.63.13
Port of moxa utility service
OBJECT-TYPE    
  INTEGER 1..65535  

httpMaxLoginUsers 1.3.6.1.4.1.8691.7.69.1.63.14
Configure HTTP/HTTPS maximum login users
OBJECT-TYPE    
  INTEGER 1..10  

telnetMaxLoginUsers 1.3.6.1.4.1.8691.7.69.1.63.15
Configure TELNET/SSH maximum login users
OBJECT-TYPE    
  INTEGER 1..5  

moxaNewCmdEnable 1.3.6.1.4.1.8691.7.69.1.63.16
Status of new moxa utility service
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

passwordPolicy 1.3.6.1.4.1.8691.7.69.1.70
OBJECT IDENTIFIER    

pwdMinLength 1.3.6.1.4.1.8691.7.69.1.70.1
Configure the minimum password length.
OBJECT-TYPE    
  INTEGER 4..16  

pwdComplexityCheckEnable 1.3.6.1.4.1.8691.7.69.1.70.2
Enable password complexity check.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

pwdComplexityCheckDigitEnable 1.3.6.1.4.1.8691.7.69.1.70.3
Add password complexity check with digit.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

pwdComplexityCheckAlphabetEnable 1.3.6.1.4.1.8691.7.69.1.70.4
Add password complexity check with alphabet.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

pwdComplexityCheckSpecialCharEnable 1.3.6.1.4.1.8691.7.69.1.70.5
Add password complexity check with special-characters.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

loginLockout 1.3.6.1.4.1.8691.7.69.1.71
OBJECT IDENTIFIER    

loginFailureLockoutEnable 1.3.6.1.4.1.8691.7.69.1.71.1
Enable login failure lockout.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

loginFailureLockoutRetrys 1.3.6.1.4.1.8691.7.69.1.71.2
Configure login failure lockout retry threshhold.
OBJECT-TYPE    
  INTEGER 1..10  

loginFailureLockoutTime 1.3.6.1.4.1.8691.7.69.1.71.3
Configure login failure lockout time.(Min)
OBJECT-TYPE    
  INTEGER 1..60  

systemNotifyMessage 1.3.6.1.4.1.8691.7.69.1.72
OBJECT IDENTIFIER    

httpLoginMessage 1.3.6.1.4.1.8691.7.69.1.72.1
Configure HTTP/HTTPS login message.
OBJECT-TYPE    
  DisplayString  

httpLoginFailureMessage 1.3.6.1.4.1.8691.7.69.1.72.2
Configure HTTP/HTTPS login failure message.
OBJECT-TYPE    
  DisplayString  

syslogManagement 1.3.6.1.4.1.8691.7.69.1.73
OBJECT IDENTIFIER    

loggingCapacityThreshold 1.3.6.1.4.1.8691.7.69.1.73.1
Configure event log capacity warning threshold.
OBJECT-TYPE    
  INTEGER 0..100  

loggingCapacityTrapWarningEnable 1.3.6.1.4.1.8691.7.69.1.73.2
Enable event log capacity SNMP trap warning.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

loggingCapacityEmailWarningEnable 1.3.6.1.4.1.8691.7.69.1.73.3
Enable event log capacity email warning.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

loggingOversizeAction 1.3.6.1.4.1.8691.7.69.1.73.4
Set event log over-size action.
OBJECT-TYPE    
  INTEGER overwrite(0), stoprecord(1)  

certificateManagement 1.3.6.1.4.1.8691.7.69.1.74
OBJECT IDENTIFIER    

sslCertGen 1.3.6.1.4.1.8691.7.69.1.74.1
Generate SSL certificate.
OBJECT-TYPE    
  INTEGER na(0), generate(1)  

sshKeyGen 1.3.6.1.4.1.8691.7.69.1.74.2
Generate SSH host key.
OBJECT-TYPE    
  INTEGER na(0), generate(1)  

switchLocator 1.3.6.1.4.1.8691.7.69.1.64
OBJECT IDENTIFIER    

blinkingLocatorLED 1.3.6.1.4.1.8691.7.69.1.64.1
Blinking switch locator LED.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

disableLocatorLEDTime 1.3.6.1.4.1.8691.7.69.1.64.2
Configure back-off time for disable switch locator LED.
OBJECT-TYPE    
  INTEGER  

uiVersion 1.3.6.1.4.1.8691.7.69.1.65
New UI Version
OBJECT-TYPE    
  INTEGER  

serialNumber 1.3.6.1.4.1.8691.7.69.1.78
Serial Number
OBJECT-TYPE    
  DisplayString  

configEncryptEnable 1.3.6.1.4.1.8691.7.69.1.79
Configuration File Encryption Setting.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)