MICOM-4400-T1E1-MIB

File: MICOM-4400-T1E1-MIB.mib (79427 bytes)

Imported modules

RFC-1215 MICOM-SYS-MIB RFC1155-SMI
RFC-1212 SNMPv2-TC MICOM-OSCAR-MIB

Imported symbols

TRAP-TYPE mcmSysAsciiTimeOfDay Counter
OBJECT-TYPE DisplayString micom-oscar

Defined Types

Mcm4400t1e1LineCfgEntry  
SEQUENCE    
  mcm4400t1e1LineCfgLineID INTEGER
  mcm4400t1e1LineCfgProfileNum INTEGER

Mcm4400t1e1ProfCfgEntry  
SEQUENCE    
  mcm4400t1e1ProfCfgProfileNum INTEGER
  mcm4400t1e1ProfCfgT1FrameFmt INTEGER
  mcm4400t1e1ProfCfgT1LineCode INTEGER
  mcm4400t1e1ProfCfgE1LineCode INTEGER
  mcm4400t1e1ProfCfgIdleCode INTEGER
  mcm4400t1e1ProfCfgT1LineBuildOut INTEGER
  mcm4400t1e1ProfCfgT1Loopback INTEGER
  mcm4400t1e1ProfCfgE1CRC4 INTEGER
  mcm4400t1e1ProfCfgE1TS16Conn INTEGER

Mcm4400t1e1DS0ChConnEntry  
SEQUENCE    
  mcm4400t1e1DS0ChConnLineID INTEGER
  mcm4400t1e1DS0ChConnDS0Index INTEGER
  mcm4400t1e1DS0ChConnState INTEGER

Mcm4400t1e1DPCfgEntry  
SEQUENCE    
  mcm4400t1e1DPCfgPortNum INTEGER
  mcm4400t1e1DPCfgDataRate INTEGER
  mcm4400t1e1DPCfgClock INTEGER
  mcm4400t1e1DPCfgDTRCntl INTEGER
  mcm4400t1e1DPCfgRTSCntl INTEGER

Nvm4400t1e1LineCfgEntry  
SEQUENCE    
  nvm4400t1e1LineCfgLineID INTEGER
  nvm4400t1e1LineCfgProfileNum INTEGER

Nvm4400t1e1ProfCfgEntry  
SEQUENCE    
  nvm4400t1e1ProfCfgProfileNum INTEGER
  nvm4400t1e1ProfCfgT1FrameFmt INTEGER
  nvm4400t1e1ProfCfgT1LineCode INTEGER
  nvm4400t1e1ProfCfgE1LineCode INTEGER
  nvm4400t1e1ProfCfgIdleCode INTEGER
  nvm4400t1e1ProfCfgT1LineBuildOut INTEGER
  nvm4400t1e1ProfCfgT1Loopback INTEGER
  nvm4400t1e1ProfCfgE1CRC4 INTEGER
  nvm4400t1e1ProfCfgE1TS16Conn INTEGER

Nvm4400t1e1DS0ChConnEntry  
SEQUENCE    
  nvm4400t1e1DS0ChConnLineID INTEGER
  nvm4400t1e1DS0ChConnDS0Index INTEGER
  nvm4400t1e1DS0ChConnState INTEGER

Nvm4400t1e1DPCfgEntry  
SEQUENCE    
  nvm4400t1e1DPCfgPortNum INTEGER
  nvm4400t1e1DPCfgDataRate INTEGER
  nvm4400t1e1DPCfgClock INTEGER
  nvm4400t1e1DPCfgDTRCntl INTEGER
  nvm4400t1e1DPCfgRTSCntl INTEGER

Mcm4400t1e1LineStatusEntry  
SEQUENCE    
  mcm4400t1e1LineStatusLineIndex INTEGER
  mcm4400t1e1LineStatusInterface INTEGER
  mcm4400t1e1LineStatusImpedance INTEGER
  mcm4400t1e1LineStatusTestMode INTEGER
  mcm4400t1e1LineStatusTestingDS0Ch INTEGER
  mcm4400t1e1LineStatusAISAlarm INTEGER
  mcm4400t1e1LineStatusRedAlarm INTEGER
  mcm4400t1e1LineStatusYellowAlarm INTEGER
  mcm4400t1e1LineStatusTS16AIS INTEGER
  mcm4400t1e1LineStatusOOSMFAlarm INTEGER
  mcm4400t1e1LineStatusMFASAlarm INTEGER
  mcm4400t1e1LineStatusFASAlarm INTEGER
  mcm4400t1e1LineStatusOOCMFAlarm INTEGER

Mcm4400t1e1DPStatusEntry  
SEQUENCE    
  mcm4400t1e1DPStatusPortNumber INTEGER
  mcm4400t1e1DPStatusDTRInputSt INTEGER
  mcm4400t1e1DPStatusRTSInputSt INTEGER
  mcm4400t1e1DPStatusDSROutputSt INTEGER
  mcm4400t1e1DPStatusDCDOutputSt INTEGER
  mcm4400t1e1DPStatusCTSOutputSt INTEGER

Mcm4400t1e1DS0ChSigEntry  
SEQUENCE    
  mcm4400t1e1DS0ChSigLineID INTEGER
  mcm4400t1e1DS0ChSigDS0Index INTEGER
  mcm4400t1e1DS0ChSigInABCDBits INTEGER
  mcm4400t1e1DS0ChSigOutABCDBits INTEGER

Mcm4400t1e1LineStatsEntry  
SEQUENCE    
  mcm4400t1e1LineStatsLineIndex INTEGER
  mcm4400t1e1LineStatsInterface INTEGER
  mcm4400t1e1LineStatsFramingBitError Counter
  mcm4400t1e1LineStatsLineCdViolation Counter
  mcm4400t1e1LineStatsFarEndBlkError Counter
  mcm4400t1e1LineStatsCRCError Counter
  mcm4400t1e1LineStatsBufferOverrun Counter
  mcm4400t1e1LineStatsBufferUnderrun Counter
  mcm4400t1e1LineStatsFrmSyncBitError Counter
  mcm4400t1e1LineStatsOutOfFrame Counter
  mcm4400t1e1LineStatsTotalFrameSlip Counter

Mcm4400t1e1DS0ChTestCmdEntry  
SEQUENCE    
  mcm4400t1e1DS0ChTestCmdLineID INTEGER
  mcm4400t1e1DS0ChTestCmdDS0Index INTEGER
  mcm4400t1e1DS0ChTestCmdTstPattern INTEGER

Mcm4400t1e1LineTestCmdEntry  
SEQUENCE    
  mcm4400t1e1LineTestCmdLineID INTEGER
  mcm4400t1e1LineTestCmdTstPattern INTEGER

Mcm4400t1e1DPTestCmdEntry  
SEQUENCE    
  mcm4400t1e1DPTestCmdPortNum INTEGER
  mcm4400t1e1DPTestCmdTstPattern INTEGER

Defined Values

micom-2t1e1 1.3.6.1.4.1.335.1.4.22
OBJECT IDENTIFIER    

t1e1-r2-configuration 1.3.6.1.4.1.335.1.4.22.1
OBJECT IDENTIFIER    

t1e1-r2-control 1.3.6.1.4.1.335.1.4.22.2
OBJECT IDENTIFIER    

t1e1-r2-status 1.3.6.1.4.1.335.1.4.22.3
OBJECT IDENTIFIER    

t1e1-r2-statistics 1.3.6.1.4.1.335.1.4.22.4
OBJECT IDENTIFIER    

mcm4400t1e1LineCfgTable 1.3.6.1.4.1.335.1.4.22.1.1
NAME = ; DESC = The T1/E1 Line Configuration table. \ (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1LineCfgEntry

mcm4400t1e1LineCfgEntry 1.3.6.1.4.1.335.1.4.22.1.1.1
NAME = ; DESC = An entry in the T1/E1 Line Configuration \ table. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1LineCfgEntry  

mcm4400t1e1LineCfgLineID 1.3.6.1.4.1.335.1.4.22.1.1.1.1
NAME = ; DESC = The T1/E1 line identification specifies which line \ is to be configured. Used as the index to the \ T1/E1 Line Configuration table. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2)  

mcm4400t1e1LineCfgProfileNum 1.3.6.1.4.1.335.1.4.22.1.1.1.2
NAME = ; DESC = The value of this object indicates the profile \ to be used to configure the specified T1/E1 \ line. (Operational); HELP = 1: expected as default profile for local line. \ 2: expected as default profile for network line.; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2  

mcm4400t1e1ProfCfgTable 1.3.6.1.4.1.335.1.4.22.1.2
NAME = ; DESC = The T1/E1 Profile Configuration table. \ (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1ProfCfgEntry

mcm4400t1e1ProfCfgEntry 1.3.6.1.4.1.335.1.4.22.1.2.1
NAME = ; DESC = An entry in the T1/E1 Profile Configuration \ table. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1ProfCfgEntry  

mcm4400t1e1ProfCfgProfileNum 1.3.6.1.4.1.335.1.4.22.1.2.1.1
NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the T1/E1 \ Profile Configuration table. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

mcm4400t1e1ProfCfgT1FrameFmt 1.3.6.1.4.1.335.1.4.22.1.2.1.2
NAME = ; DESC = The value of this object specifies the T1 \ frame format used in the line. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER superFrame(1), extendedSuperFrame(2)  

mcm4400t1e1ProfCfgT1LineCode 1.3.6.1.4.1.335.1.4.22.1.2.1.3
NAME = ; DESC = The value of this object specifies the T1 \ coding format used in the line. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER aMI(1), b8ZS(2)  

mcm4400t1e1ProfCfgE1LineCode 1.3.6.1.4.1.335.1.4.22.1.2.1.4
NAME = ; DESC = The value of this object specifies the E1 \ coding format used in the line. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER aMI(1), hDB3(2)  

mcm4400t1e1ProfCfgIdleCode 1.3.6.1.4.1.335.1.4.22.1.2.1.5
NAME = ; DESC = The value of this object specifies the code \ to be filled in the line when idle. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..ff  

mcm4400t1e1ProfCfgT1LineBuildOut 1.3.6.1.4.1.335.1.4.22.1.2.1.6
NAME = ; DESC = The value of this object specifies the cable \ length attached to a local T1 line. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lessThan110Feet(1), lessThan220Feet(2), lessThan330Feet(3), lessThan440Feet(4), externalLBO(5), greaterThan665Feet(6), lessThan550Feet(7), lessThan660Feet(8)  

mcm4400t1e1ProfCfgT1Loopback 1.3.6.1.4.1.335.1.4.22.1.2.1.7
NAME = ; DESC = The value of this object specifies whether \ to enable or disable the T1 line loopback \ to be invoked. (Operational); HELP = 1: expected as default for a local T1 line profile. \ 2: expected as default for a network T1 line profile.; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

mcm4400t1e1ProfCfgE1CRC4 1.3.6.1.4.1.335.1.4.22.1.2.1.8
NAME = ; DESC = The value of this object specifies whether \ to enable or disable a T1 line CRC4. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

mcm4400t1e1ProfCfgE1TS16Conn 1.3.6.1.4.1.335.1.4.22.1.2.1.9
NAME = ; DESC = The value of this object specifies where the \ TS16 goes (for a T1 line). (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER toCAS(1), idle(2), bypass(3), toDataPort1(4), toDataPort2(5)  

mcm4400t1e1DS0ChConnTable 1.3.6.1.4.1.335.1.4.22.1.3
NAME = ; DESC = The T1/E1 DS0 Channel Connection \ Configuration table.(Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1DS0ChConnEntry

mcm4400t1e1DS0ChConnEntry 1.3.6.1.4.1.335.1.4.22.1.3.1
NAME = ; DESC = An entry in the T1/E1 DS0 Channel \ Connection Configuration table. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1DS0ChConnEntry  

mcm4400t1e1DS0ChConnLineID 1.3.6.1.4.1.335.1.4.22.1.3.1.1
NAME = ; DESC = The T1/E1 line identification specifies which line \ is to be configured. Used as an index to the \ T1/E1 DS0 Channel Connection Configuration \ table. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2)  

mcm4400t1e1DS0ChConnDS0Index 1.3.6.1.4.1.335.1.4.22.1.3.1.2
NAME = ; DESC = The T1/E1 DS0 index specifies which time slot \ is to be connected. Used as an index to the \ T1/E1 DS0 Channel Connection Configuration \ table. (Operational); HELP = For T1, 24 is the maximum. An error will be \ returned for a T1 DS0 index greater than 24.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

mcm4400t1e1DS0ChConnState 1.3.6.1.4.1.335.1.4.22.1.3.1.3
NAME = ; DESC = The value of this object specifies where the \ T1/E1 line channel slot (DS0) is to be connected \ to. (Operational); HELP = Note 1: if 2-37 is selected, the previous setting \ must be idle, or an error will be returned. \ Note 2: if idle is specified and the previous setting \ was bypass (voice or data), the corresponding DS0 \ in the other line will also be set to idle automatically. \ Note 3: if bypass (voice or data) is specified, the \ corresponding DS0 in the other line will also be \ set to the same bypass mode automatically.; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER idle(1), bypassVoice(2), bypassData(3), toWANPort1(4), toWANPort2(5), toDataPort1(6), toDataPort2(7), toDVMChannelB1(8), toDVMChannelB2(9), toDVMChannelB3(10), toDVMChannelB4(11), toDVMChannelB5(12), toDVMChannelB6(13), toDVMChannelC1(14), toDVMChannelC2(15), toDVMChannelC3(16), toDVMChannelC4(17), toDVMChannelC5(18), toDVMChannelC6(19), toDVMChannelC7(20), toDVMChannelC8(21), toDVMChannelC9(22), toDVMChannelC10(23), toDVMChannelC11(24), toDVMChannelC12(25), toDVMChannelD1(26), toDVMChannelD2(27), toDVMChannelD3(28), toDVMChannelD4(29), toDVMChannelD5(30), toDVMChannelD6(31), toDVMChannelD7(32), toDVMChannelD8(33), toDVMChannelD9(34), toDVMChannelD10(35), toDVMChannelD11(36), toDVMChannelD12(37)  

mcm4400t1e1DPCfgTable 1.3.6.1.4.1.335.1.4.22.1.4
NAME = ; DESC = The T1/E1 Data Port Configuration table. \ (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1DPCfgEntry

mcm4400t1e1DPCfgEntry 1.3.6.1.4.1.335.1.4.22.1.4.1
NAME = ; DESC = An entry in the T1/E1 Data Port \ Configuration table. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1DPCfgEntry  

mcm4400t1e1DPCfgPortNum 1.3.6.1.4.1.335.1.4.22.1.4.1.1
NAME = ; DESC = The T1/E1 port number specifies which data port \ is to be configured. Used as an index to the \ T1/E1 Data Port Configuration table. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER port1(1), port2(2)  

mcm4400t1e1DPCfgDataRate 1.3.6.1.4.1.335.1.4.22.1.4.1.2
NAME = ; DESC = The value of this object selects the baud rate \ for the specified data port. (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER rate64kbps(1), rate56kbps(2)  

mcm4400t1e1DPCfgClock 1.3.6.1.4.1.335.1.4.22.1.4.1.3
NAME = ; DESC = The value of this object selects the clock \ source for the specified data port. \ (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internalClock(1), tailCircuit(2)  

mcm4400t1e1DPCfgDTRCntl 1.3.6.1.4.1.335.1.4.22.1.4.1.4
NAME = ; DESC = The value of this object selects the DTR \ control for the specified data port. \ (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), forcedOn(2)  

mcm4400t1e1DPCfgRTSCntl 1.3.6.1.4.1.335.1.4.22.1.4.1.5
NAME = ; DESC = The value of this object selects the RTS \ control for the specified data port. \ (Operational); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), forcedOn(2)  

mcm4400t1e1SysCfgClockSource 1.3.6.1.4.1.335.1.4.22.1.5
NAME = ; DESC = The value of this object specifies where the \ system clock comes from. (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER networkLineExternal(1), localLineExternal(2), internal(3)  

nvm4400t1e1LineCfgTable 1.3.6.1.4.1.335.1.4.22.1.6
NAME = ; DESC = The T1/E1 Line Configuration table. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nvm4400t1e1LineCfgEntry

nvm4400t1e1LineCfgEntry 1.3.6.1.4.1.335.1.4.22.1.6.1
NAME = ; DESC = An entry in the T1/E1 Line Configuration \ table. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nvm4400t1e1LineCfgEntry  

nvm4400t1e1LineCfgLineID 1.3.6.1.4.1.335.1.4.22.1.6.1.1
NAME = ; DESC = The T1/E1 line identification specifies which line \ is to be configured. Used as the index to the \ T1/E1 Line Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2)  

nvm4400t1e1LineCfgProfileNum 1.3.6.1.4.1.335.1.4.22.1.6.1.2
NAME = ; DESC = The value of this object indicates the profile \ to be used to configure the specified T1/E1 \ line. (Configuration); HELP = 1: expected as default profile for local line. \ 2: expected as default profile for network line.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

nvm4400t1e1ProfCfgTable 1.3.6.1.4.1.335.1.4.22.1.7
NAME = ; DESC = The T1/E1 Profile Configuration table. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nvm4400t1e1ProfCfgEntry

nvm4400t1e1ProfCfgEntry 1.3.6.1.4.1.335.1.4.22.1.7.1
NAME = ; DESC = An entry in the T1/E1 Profile Configuration \ table. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nvm4400t1e1ProfCfgEntry  

nvm4400t1e1ProfCfgProfileNum 1.3.6.1.4.1.335.1.4.22.1.7.1.1
NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the T1/E1 \ Profile Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

nvm4400t1e1ProfCfgT1FrameFmt 1.3.6.1.4.1.335.1.4.22.1.7.1.2
NAME = ; DESC = The value of this object specifies the T1 \ frame format used in the line. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER superFrame(1), extendedSuperFrame(2)  

nvm4400t1e1ProfCfgT1LineCode 1.3.6.1.4.1.335.1.4.22.1.7.1.3
NAME = ; DESC = The value of this object specifies the T1 \ coding format used in the line. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER aMI(1), b8ZS(2)  

nvm4400t1e1ProfCfgE1LineCode 1.3.6.1.4.1.335.1.4.22.1.7.1.4
NAME = ; DESC = The value of this object specifies the E1 \ coding format used in the line. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER aMI(1), hDB3(2)  

nvm4400t1e1ProfCfgIdleCode 1.3.6.1.4.1.335.1.4.22.1.7.1.5
NAME = ; DESC = The value of this object specifies the code \ to be filled in the line when idle. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..ff  

nvm4400t1e1ProfCfgT1LineBuildOut 1.3.6.1.4.1.335.1.4.22.1.7.1.6
NAME = ; DESC = The value of this object specifies the cable \ length attached to a local T1 line. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lessThan110Feet(1), lessThan220Feet(2), lessThan330Feet(3), lessThan440Feet(4), externalLBO(5), greaterThan665Feet(6), lessThan550Feet(7), lessThan660Feet(8)  

nvm4400t1e1ProfCfgT1Loopback 1.3.6.1.4.1.335.1.4.22.1.7.1.7
NAME = ; DESC = The value of this object specifies whether \ to enable or disable the T1 line loopback \ to be invoked. (Configuration); HELP = 1: expected as default for a local T1 line profile. \ 2: expected as default for a network T1 line profile.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

nvm4400t1e1ProfCfgE1CRC4 1.3.6.1.4.1.335.1.4.22.1.7.1.8
NAME = ; DESC = The value of this object specifies whether \ to enable or disable a T1 line CRC4. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

nvm4400t1e1ProfCfgE1TS16Conn 1.3.6.1.4.1.335.1.4.22.1.7.1.9
NAME = ; DESC = The value of this object specifies where the \ TS16 goes (for a T1 line). (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER toCAS(1), idle(2), bypass(3), toDataPort1(4), toDataPort2(5)  

nvm4400t1e1DS0ChConnTable 1.3.6.1.4.1.335.1.4.22.1.8
NAME = ; DESC = The T1/E1 DS0 Channel Connection \ Configuration table.(Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nvm4400t1e1DS0ChConnEntry

nvm4400t1e1DS0ChConnEntry 1.3.6.1.4.1.335.1.4.22.1.8.1
NAME = ; DESC = An entry in the T1/E1 DS0 Channel \ Connection Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nvm4400t1e1DS0ChConnEntry  

nvm4400t1e1DS0ChConnLineID 1.3.6.1.4.1.335.1.4.22.1.8.1.1
NAME = ; DESC = The T1/E1 line identification specifies which line \ is to be configured. Used as an index to the \ T1/E1 DS0 Channel Connection Configuration \ table. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2)  

nvm4400t1e1DS0ChConnDS0Index 1.3.6.1.4.1.335.1.4.22.1.8.1.2
NAME = ; DESC = The T1/E1 DS0 index specifies which time slot \ is to be connected. Used as an index to the \ T1/E1 DS0 Channel Connection Configuration \ table. (Configuration); HELP = For T1, 24 is the maximum. An error will be \ returned for a T1 DS0 index greater than 24.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

nvm4400t1e1DS0ChConnState 1.3.6.1.4.1.335.1.4.22.1.8.1.3
NAME = ; DESC = The value of this object specifies where the \ T1/E1 line channel slot (DS0) is to be connected \ to. (Configuration); HELP = Note 1: if 2-37 is selected, the previous setting \ must be idle, or an error will be returned. \ Note 2: if idle is specified and the previous setting \ was bypass (voice or data), the corresponding DS0 \ in the other line will also be set to idle automatically. \ Note 3: if bypass (voice or data) is specified, the \ corresponding DS0 in the other line will also be \ set to the same bypass mode automatically.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(1), bypassVoice(2), bypassData(3), toWANPort1(4), toWANPort2(5), toDataPort1(6), toDataPort2(7), toDVMChannelB1(8), toDVMChannelB2(9), toDVMChannelB3(10), toDVMChannelB4(11), toDVMChannelB5(12), toDVMChannelB6(13), toDVMChannelC1(14), toDVMChannelC2(15), toDVMChannelC3(16), toDVMChannelC4(17), toDVMChannelC5(18), toDVMChannelC6(19), toDVMChannelC7(20), toDVMChannelC8(21), toDVMChannelC9(22), toDVMChannelC10(23), toDVMChannelC11(24), toDVMChannelC12(25), toDVMChannelD1(26), toDVMChannelD2(27), toDVMChannelD3(28), toDVMChannelD4(29), toDVMChannelD5(30), toDVMChannelD6(31), toDVMChannelD7(32), toDVMChannelD8(33), toDVMChannelD9(34), toDVMChannelD10(35), toDVMChannelD11(36), toDVMChannelD12(37)  

nvm4400t1e1DPCfgTable 1.3.6.1.4.1.335.1.4.22.1.9
NAME = ; DESC = The T1/E1 Data Port Configuration table. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nvm4400t1e1DPCfgEntry

nvm4400t1e1DPCfgEntry 1.3.6.1.4.1.335.1.4.22.1.9.1
NAME = ; DESC = An entry in the T1/E1 Data Port \ Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nvm4400t1e1DPCfgEntry  

nvm4400t1e1DPCfgPortNum 1.3.6.1.4.1.335.1.4.22.1.9.1.1
NAME = ; DESC = The T1/E1 port number specifies which data port \ is to be configured. Used as an index to the \ T1/E1 Data Port Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER port1(1), port2(2)  

nvm4400t1e1DPCfgDataRate 1.3.6.1.4.1.335.1.4.22.1.9.1.2
NAME = ; DESC = The value of this object selects the baud rate \ for the specified data port. (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rate64kbps(1), rate56kbps(2)  

nvm4400t1e1DPCfgClock 1.3.6.1.4.1.335.1.4.22.1.9.1.3
NAME = ; DESC = The value of this object selects the clock \ source for the specified data port. \ (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER internalClock(1), tailCircuit(2)  

nvm4400t1e1DPCfgDTRCntl 1.3.6.1.4.1.335.1.4.22.1.9.1.4
NAME = ; DESC = The value of this object selects the DTR \ control for the specified data port. \ (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), forcedOn(2)  

nvm4400t1e1DPCfgRTSCntl 1.3.6.1.4.1.335.1.4.22.1.9.1.5
NAME = ; DESC = The value of this object selects the RTS \ control for the specified data port. \ (Configuration); HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), forcedOn(2)  

nvm4400t1e1SysCfgClockSource 1.3.6.1.4.1.335.1.4.22.1.10
NAME = ; DESC = The value of this object specifies where the \ system clock comes from. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER networkLineExternal(1), localLineExternal(2), internal(3)  

mcm4400t1e1LineStatusTable 1.3.6.1.4.1.335.1.4.22.3.1
NAME = ; DESC = The T1/E1 Line Status Display table. \ HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1LineStatusEntry

mcm4400t1e1LineStatusEntry 1.3.6.1.4.1.335.1.4.22.3.1.1
NAME = ; DESC = An entry in the T1/E1 Line Status Display \ table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1LineStatusEntry  

mcm4400t1e1LineStatusLineIndex 1.3.6.1.4.1.335.1.4.22.3.1.1.1
NAME = ; DESC = The T1/E1 line index specifies which line is to \ be displayed. Used as an index to the \ T1/E1 Line Status Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER localLine(1), networkLine(2)  

mcm4400t1e1LineStatusInterface 1.3.6.1.4.1.335.1.4.22.3.1.1.2
NAME = ; DESC = The value of this object indicates the interface \ type as either T1 or E1 for the \ T1/E1 Line Status Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

mcm4400t1e1LineStatusImpedance 1.3.6.1.4.1.335.1.4.22.3.1.1.3
NAME = ; DESC = The value of this object indicates the impedance \ for the specified line.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER line120ohm(1), line75ohm(2)  

mcm4400t1e1LineStatusTestMode 1.3.6.1.4.1.335.1.4.22.3.1.1.4
NAME = ; DESC = The value of this object indicates if the specified \ line is in a loopback test mode.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), inLineLoopback(2), inChannelLoopback(3), inChannelPatternTest(4)  

mcm4400t1e1LineStatusTestingDS0Ch 1.3.6.1.4.1.335.1.4.22.3.1.1.5
NAME = ; DESC = The value of this object indicates which DS0 \ channel is in channel loopback or channel pattern \ test mode now.; HELP = 0: none.\ 1-30: DS0 channel number.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..30  

mcm4400t1e1LineStatusAISAlarm 1.3.6.1.4.1.335.1.4.22.3.1.1.6
NAME = ; DESC = The value of this object indicates if the AIS \ (Alarm Indication Signal) alarm is preset for \ the specified line.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

mcm4400t1e1LineStatusRedAlarm 1.3.6.1.4.1.335.1.4.22.3.1.1.7
NAME = ; DESC = The value of this object indicates if the Red \ alarm is preset for the specified line.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

mcm4400t1e1LineStatusYellowAlarm 1.3.6.1.4.1.335.1.4.22.3.1.1.8
NAME = ; DESC = The value of this object indicates if the Yellow \ alarm is preset for the specified line. (Not \ applicable in E1.) ; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2), notApplicable(3)  

mcm4400t1e1LineStatusTS16AIS 1.3.6.1.4.1.335.1.4.22.3.1.1.9
NAME = ; DESC = The value of this object indicates if the TS16 \ (Time Slot 16) AIS alarm is preset for the \ specified line. (Not applicable in T1.) ; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2), notApplicable(3)  

mcm4400t1e1LineStatusOOSMFAlarm 1.3.6.1.4.1.335.1.4.22.3.1.1.10
NAME = ; DESC = The value of this object indicates if the \ OOSMF (Out Of Signal Multi-Frame) alarm \ is preset for the specified line. (Not \ applicable in T1.) ; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2), notApplicable(3)  

mcm4400t1e1LineStatusMFASAlarm 1.3.6.1.4.1.335.1.4.22.3.1.1.11
NAME = ; DESC = The value of this object indicates if the \ MFAS (Multi-Frame Alignment Signal - \ Y bit) alarm is preset for the specified line. \ (Not applicable in T1.) ; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2), notApplicable(3)  

mcm4400t1e1LineStatusFASAlarm 1.3.6.1.4.1.335.1.4.22.3.1.1.12
NAME = ; DESC = The value of this object indicates if the \ FAS (Frame Alignment Signal - A bit) \ alarm is preset for the specified line. \ (Not applicable in T1.) ; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2), notApplicable(3)  

mcm4400t1e1LineStatusOOCMFAlarm 1.3.6.1.4.1.335.1.4.22.3.1.1.13
NAME = ; DESC = The value of this object indicates if the \ OOCMF (Out Of CRC Multi-Frame) \ alarm is preset for the specified line. \ (Not applicable in T1.) ; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2), notApplicable(3)  

mcm4400t1e1SysStatusGroup 1.3.6.1.4.1.335.1.4.22.3.2
OBJECT IDENTIFIER    

mcm4400t1e1SysStatusCardType 1.3.6.1.4.1.335.1.4.22.3.2.1
NAME = ; DESC = The value of this object indicates the T1/E1 \ card type.; HELP = 1: TAM1 - network line only. \ 2: TAM2 - both local and network lines. \ 3: EAM1 - network line only. \ 4: EAM2 - both local and network lines.; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER t1SingleLineAccessModule(1), t1DualLineAccessModule(2), e1SingleLineAccessModule(3), e1DualLineAccessModule(4)  

mcm4400t1e1SysStatusOperStatus 1.3.6.1.4.1.335.1.4.22.3.2.2
NAME = ; DESC = The value of this object indicates the operation \ status of the T1/E1 control unit.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dead(1), aliveButNotReady(2), downloadFail(3), downloadInProgress(4), normal(5)  

mcm4400t1e1SysStatusLEDTest 1.3.6.1.4.1.335.1.4.22.3.2.3
NAME = ; DESC = The value of this object specifies if the \ LED test is in progress.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

mcm4400t1e1SysStatusSelfTestResults 1.3.6.1.4.1.335.1.4.22.3.2.4
NAME = ; DESC = The value of this object specifies the \ results of the T1/E1 self test.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER testPassed(1), testFailed(2)  

mcm4400t1e1SysStatusFlashEPROMSt 1.3.6.1.4.1.335.1.4.22.3.2.5
NAME = ; DESC = The value of this object specifies the current \ state of the flash EPROM in the T1/E1 \ access board.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), erased(2), invalidChecksum(3)  

mcm4400t1e1SysStatusApplSwID 1.3.6.1.4.1.335.1.4.22.3.2.6
NAME = ; DESC = The value of this object indicates the T1/E1 \ application software ID (Null terminated string).; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

mcm4400t1e1SysStatusBootSwVer 1.3.6.1.4.1.335.1.4.22.3.2.7
NAME = ; DESC = The value of this object indicates the T1/E1 \ software version (Null terminated string).; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

mcm4400t1e1DPStatusTable 1.3.6.1.4.1.335.1.4.22.3.3
NAME = ; DESC = The T1/E1 Data Port Status Display table. \ HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1DPStatusEntry

mcm4400t1e1DPStatusEntry 1.3.6.1.4.1.335.1.4.22.3.3.1
NAME = ; DESC = An entry in the T1/E1 Data Port Status \ Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1DPStatusEntry  

mcm4400t1e1DPStatusPortNumber 1.3.6.1.4.1.335.1.4.22.3.3.1.1
NAME = ; DESC = The value of this object specifies the data port \ number. Used as the index to the T1/E1 \ Data Port Status Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER port1(1), port2(2)  

mcm4400t1e1DPStatusDTRInputSt 1.3.6.1.4.1.335.1.4.22.3.3.1.2
NAME = ; DESC = The value of this object indicates the current \ DTR state for the specified data port.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mcm4400t1e1DPStatusRTSInputSt 1.3.6.1.4.1.335.1.4.22.3.3.1.3
NAME = ; DESC = The value of this object indicates the current \ RTS state for the specified data port.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mcm4400t1e1DPStatusDSROutputSt 1.3.6.1.4.1.335.1.4.22.3.3.1.4
NAME = ; DESC = The value of this object indicates the current \ DSR state for the specified data port.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mcm4400t1e1DPStatusDCDOutputSt 1.3.6.1.4.1.335.1.4.22.3.3.1.5
NAME = ; DESC = The value of this object indicates the current \ DCD state for the specified data port.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mcm4400t1e1DPStatusCTSOutputSt 1.3.6.1.4.1.335.1.4.22.3.3.1.6
NAME = ; DESC = The value of this object indicates the current \ CTS state for the specified data port.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mcm4400t1e1DS0ChSigTable 1.3.6.1.4.1.335.1.4.22.3.4
NAME = ; DESC = The T1/E1 DS0 Channel Signaling Display \ table. \ HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1DS0ChSigEntry

mcm4400t1e1DS0ChSigEntry 1.3.6.1.4.1.335.1.4.22.3.4.1
NAME = ; DESC = An entry in the T1/E1 DS0 Channel \ Signaling Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1DS0ChSigEntry  

mcm4400t1e1DS0ChSigLineID 1.3.6.1.4.1.335.1.4.22.3.4.1.1
NAME = ; DESC = The T1/E1 line ID specifies which line is to \ be displayed. Used as an index to the \ T1/E1 DS0 Channel Signaling Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2)  

mcm4400t1e1DS0ChSigDS0Index 1.3.6.1.4.1.335.1.4.22.3.4.1.2
NAME = ; DESC = The DS0 Index specifies which time slot is \ to be displayed. Used as an index to the \ T1/E1 DS0 Channel Signaling Display table.; HELP = For T1, 24 is the maximum. An error will be \ returned if a value greater than 24 is selected.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

mcm4400t1e1DS0ChSigInABCDBits 1.3.6.1.4.1.335.1.4.22.3.4.1.3
NAME = ; DESC = The value of this object indicates the input \ ABCD bit pattern.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..16  

mcm4400t1e1DS0ChSigOutABCDBits 1.3.6.1.4.1.335.1.4.22.3.4.1.4
NAME = ; DESC = The value of this object indicates the output \ ABCD bit pattern.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..16  

mcm4400t1e1ChTestResultsGroup 1.3.6.1.4.1.335.1.4.22.3.5
OBJECT IDENTIFIER    

mcm4400t1e1ChTestResultsLineID 1.3.6.1.4.1.335.1.4.22.3.5.1
NAME = ; DESC = The line ID specifies which T1/E1 line has \ a DS0channel in test mode.; HELP = 3 is returned if no DS0 channel is in test mode.; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2), none(3)  

mcm4400t1e1ChTestResultsDS0Ch 1.3.6.1.4.1.335.1.4.22.3.5.2
NAME = ; DESC = The value of this object specifies which DS0 \ channel is in test mode.; HELP = For T1, 24 is the maximum. Also, 0 will be \ returned if no DS0 channels are in test mode.; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..30  

mcm4400t1e1ChTestResultsErrorCnt 1.3.6.1.4.1.335.1.4.22.3.5.3
NAME = ; DESC = The value of this object indicates the number \ of errors accumulated since the test had been \ started.; HELP = An error can be detected only when in channel \ pattern test mode. Channel loopback will always \ be 0.; CAPABILITIES = NET_CFG, VPN_CFG ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsTable 1.3.6.1.4.1.335.1.4.22.4.1
NAME = ; DESC = The T1/E1 Line Statistics Display table. \ HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1LineStatsEntry

mcm4400t1e1LineStatsEntry 1.3.6.1.4.1.335.1.4.22.4.1.1
NAME = ; DESC = An entry in the T1/E1 Line Statistics \ Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1LineStatsEntry  

mcm4400t1e1LineStatsLineIndex 1.3.6.1.4.1.335.1.4.22.4.1.1.1
NAME = ; DESC = The T1/E1 line index specifies which line is to \ be displayed. Used as an index to the \ T1/E1 Line Statistics Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER localLine(1), networkLine(2)  

mcm4400t1e1LineStatsInterface 1.3.6.1.4.1.335.1.4.22.4.1.1.2
NAME = ; DESC = The value of this object indicates the interface \ type as either T1 or E1 for the \ T1/E1 Line Statistics Display table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

mcm4400t1e1LineStatsFramingBitError 1.3.6.1.4.1.335.1.4.22.4.1.1.3
NAME = ; DESC = The value of this object indicates the framing \ bit errors on the specified line.; HELP = Valid for E1 only. For T1, 0 will be returned.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsLineCdViolation 1.3.6.1.4.1.335.1.4.22.4.1.1.4
NAME = ; DESC = The value of this object indicates the line \ code violations on the specified line.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsFarEndBlkError 1.3.6.1.4.1.335.1.4.22.4.1.1.5
NAME = ; DESC = The value of this object indicates the far \ end block errors on the specified line.; HELP = Valid for E1 only. For T1, 0 will be returned.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsCRCError 1.3.6.1.4.1.335.1.4.22.4.1.1.6
NAME = ; DESC = The value of this object indicates the CRC \ errors on the specified line.; HELP = Valid for E1 only. For T1, 0 will be returned.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsBufferOverrun 1.3.6.1.4.1.335.1.4.22.4.1.1.7
NAME = ; DESC = The value of this object indicates the \ buffer overruns on the specified line.; HELP = Valid for E1 only. For T1, 0 will be returned.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsBufferUnderrun 1.3.6.1.4.1.335.1.4.22.4.1.1.8
NAME = ; DESC = The value of this object indicates the \ buffer underruns on the specified line.; HELP = Valid for E1 only. For T1, 0 will be returned.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsFrmSyncBitError 1.3.6.1.4.1.335.1.4.22.4.1.1.9
NAME = ; DESC = The value of this object indicates the frame \ synchronization bit errors on the specified line.; HELP = Valid for T1 only. For E1, 0 will be returned.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsOutOfFrame 1.3.6.1.4.1.335.1.4.22.4.1.1.10
NAME = ; DESC = The value of this object indicates the out of \ frame statistics on the specified line.; HELP = Valid for T1 only. For E1, 0 will be returned.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1LineStatsTotalFrameSlip 1.3.6.1.4.1.335.1.4.22.4.1.1.11
NAME = ; DESC = The value of this object indicates the total \ frame slips on the specified line.; HELP = Valid for T1 only. For E1, 0 will be returned.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mcm4400t1e1DS0ChTestCmdTable 1.3.6.1.4.1.335.1.4.22.2.1
NAME = ; DESC = The T1/E1 DS0 Channel Test Command \ table. \ HELP = ; CAPABILITIES = NET_OPER, VPN_OPER ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1DS0ChTestCmdEntry

mcm4400t1e1DS0ChTestCmdEntry 1.3.6.1.4.1.335.1.4.22.2.1.1
NAME = ; DESC = An entry in the T1/E1 DS0 Channel \ Test Command table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1DS0ChTestCmdEntry  

mcm4400t1e1DS0ChTestCmdLineID 1.3.6.1.4.1.335.1.4.22.2.1.1.1
NAME = ; DESC = The T1/E1 line ID specifies which line is to \ be tested. Used as an index to the \ T1/E1 DS0 Channel Test Command table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2)  

mcm4400t1e1DS0ChTestCmdDS0Index 1.3.6.1.4.1.335.1.4.22.2.1.1.2
NAME = ; DESC = The DS0 Index specifies which time slot is \ to be tested. Used as an index to the \ T1/E1 DS0 Channel Test Command table.; HELP = For T1, 24 is the maximum. An error will be \ returned if a value greater than 24 is selected.; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

mcm4400t1e1DS0ChTestCmdTstPattern 1.3.6.1.4.1.335.1.4.22.2.1.1.3
NAME = ; DESC = Setting this object will initiate various \ test pattern testing on the specified T1/E1 \ DS0 channel.; HELP = For QRSS, TP511, and Fixed, the T1/E1 \ access module will generate and verify the \ selected test pattern. \ For Loop test, it simply loops the input \ data back to the same DS0 channel. \ In T1, if 4 is specified, an error will be \ returned.; CAPABILITIES = ;
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER qrss(1), tp511(2), loop(3), fixed-E1Only(4)  

mcm4400t1e1LineTestCmdTable 1.3.6.1.4.1.335.1.4.22.2.2
NAME = ; DESC = The T1/E1 Line Test Command \ table. \ HELP = ; CAPABILITIES = NET_OPER, VPN_OPER ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1LineTestCmdEntry

mcm4400t1e1LineTestCmdEntry 1.3.6.1.4.1.335.1.4.22.2.2.1
NAME = ; DESC = An entry in the T1/E1 Line Test \ Command table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1LineTestCmdEntry  

mcm4400t1e1LineTestCmdLineID 1.3.6.1.4.1.335.1.4.22.2.2.1.1
NAME = ; DESC = The T1/E1 line ID specifies which line is to \ be tested. Used as the index to the \ T1/E1 Line Test Command table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), network(2)  

mcm4400t1e1LineTestCmdTstPattern 1.3.6.1.4.1.335.1.4.22.2.2.1.2
NAME = ; DESC = Setting this object will initiate various \ tests on the specified T1/E1 line.; HELP = Line Loopback: receiver or transmitter is \ connected to transmitter or receiver; respectively. \ Digital Loopback: data is stripped off the \ DS0 channel and reinserted in the same channel. \ External: data coming from the line. \ Internal: data going to the line.; CAPABILITIES = ;
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER externalLineLoopback(1), externalDigitalLoopback(2), internalLineLoopback(3), internalDigitalLoopback(4)  

mcm4400t1e1DPTestCmdTable 1.3.6.1.4.1.335.1.4.22.2.3
NAME = ; DESC = The T1/E1 Data Port Test Command \ table. \ HELP = ; CAPABILITIES = NET_OPER, VPN_OPER ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Mcm4400t1e1DPTestCmdEntry

mcm4400t1e1DPTestCmdEntry 1.3.6.1.4.1.335.1.4.22.2.3.1
NAME = ; DESC = An entry in the T1/E1 Data Port \ Test Command table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Mcm4400t1e1DPTestCmdEntry  

mcm4400t1e1DPTestCmdPortNum 1.3.6.1.4.1.335.1.4.22.2.3.1.1
NAME = ; DESC = The T1/E1 Port Number specifies which data \ port is to be tested. Used as the index to the \ T1/E1 Data Port Test Command table.; HELP = ; CAPABILITIES = ;
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dataPort1(1), dataPort2(2)  

mcm4400t1e1DPTestCmdTstPattern 1.3.6.1.4.1.335.1.4.22.2.3.1.2
NAME = ; DESC = Setting this object will initiate various \ tests on the specified T1/E1 data port.; HELP = External: loop back data coming from the \ device attached to the port. \ Internal: loop back data coming from the \ DS0 channel.; CAPABILITIES = ;
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER externalLoopback(1), internalLoopback(2)  

mcm4400t1e1SysControlActionCmd 1.3.6.1.4.1.335.1.4.22.2.4
NAME = ; DESC = Setting this object will perform various \ actions on the T1/E1 system. \ Note: Starting with software release 3.0, \ the enumeration clearCounter (3) is \ not supported. The enumeration is included \ here only to support backwards compatibility \ for software versions prior to release 3.0.; HELP = 1: initiate LED test. \ 2: reset T1/E1 module. \ 3: clear statistics counters. \ 4: download code. \ 5: stop DS0 channel test. \ 6: stop line test. \ 7: stop port test. \ 8: stop LED test. \ 9: stop all tests.; CAPABILITIES = NET_OPER, VPN_OPER ;
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER testLED(1), resetT1E1(2), clearCounter(3), download(4), stopChannelTest(5), stopLineTest(6), stopPortTest(7), stopLEDTest(8), stopAllTests(9)  

mcm4400T1NoCodeImage 1
NAME = ; DESC = Indicates that the built image doesn't \ contain T1 code.\ Severity Level: MAJOR.; HELP = The Image loaded does not contain T1 code.\ Load a new Image that includes T1 code, or \ consult with the System Admin. or Field \ Personnel.;
TRAP-TYPE    

mcm4400T1DownloadFail 2
NAME = ; DESC = Indicates a failure occurred during the T1 \ code download.\ Severity Level: MAJOR; HELP = Retry the download. Re-boot the access device and \ check if it downloads correctly. Also, verify \ the T1 code that is build with access device image \ is the right version. If problem persist, consult \ your system admin., or field personnel.;
TRAP-TYPE    

mcm4400T1OutOfOrder 3
NAME = ; DESC = Indicates the T1 is not responding.\ Severity Level: CRITICAL.; HELP = Management frame is out of order. Check for \ Framing error. If it does not recover, Please \ contact your Sys Admin. or Field personnel.;
TRAP-TYPE    

mcm4400T1OutOfOrderRecovered 4
NAME = ; DESC = Indicates recovery from the T1 out of order condition.\ Severity Level: INFORMATIVE.; HELP = T1 is responding. Normal Status Indicator.;
TRAP-TYPE    

mcm4400T1FailToSyncUp 5
NAME = ; DESC = Indicates the T1 is unable to sync up.\ Severity Level : CRITICAL.; HELP = Check the physical connection locally, and \ to the remote device. Possible protocol error. \ If problem still persist, contact your \ system admin., or field personnel.;
TRAP-TYPE    

mcm4400T1FailToSyncUpRecovered 6
NAME = ; DESC = Indicates recovery from the T1 failure \ to sync up condition.\ Severity Level: INFORMATIVE.; HELP = T1 has recovered. Normal Status Indicator.;
TRAP-TYPE    

mcm4400T1AISAlarmSet 7
NAME = ; DESC = Indicates a T1 AIS Alarm condition is present.\ Severity Level: CRITICAL.; HELP = Check physical link of the local T1, and the Remote \ PBX. Possible Framing error. If problem is not \ resolved, contact sys admin., or field personnel.;
TRAP-TYPE    

mcm4400T1AISAlarmClear 8
NAME = ; DESC = Indicates a T1 AIS Alarm condition has cleared.\ Severity Level: INFORMATIVE.; HELP = T1 AIS Alarm is cleared. Normal Status Indicator.;
TRAP-TYPE    

mcm4400T1RedAlarmSet 9
NAME = ; DESC = Indicates a T1 Red Alarm condition is present.\ Severity Level: CRITICAL.; HELP = Check the Physical Connection to remote. \ If the Alarm condition is still persistant, \ contact your Field Personnel.;
TRAP-TYPE    

mcm4400T1RedAlarmClear 10
NAME = ; DESC = Indicates a T1 Red Alarm condition has cleared.\ Severity Level: IMFORMATIVE. ; HELP = Red Alarm Cleared. Normal Status Indicator!.;
TRAP-TYPE    

mcm4400T1YellowAlarmSet 11
NAME = ; DESC = Indicates a T1 Yellow Alarm condition is present.\ Severity Level: MINOR.; HELP = TX or RX side for physical connection may be faulty; \ Possible Framing error with Remote device. Run Loopback \ test if possible, & determine the problem. If that does not\ help, please contact Field Personnel or System admin.;
TRAP-TYPE    

mcm4400T1YellowAlarmClear 12
NAME = ; DESC = Indicates a T1 Yellow Alarm condition has cleared.\ Severity Level: INFORMATIVE.; HELP = Yellow Alarm is cleared. Normal Status Indicator!.;
TRAP-TYPE    

mcm4400E1NoCodeImage 13
NAME = ; DESC = Indicates that the built image doesn't \ contain E1 code.\ Severity Level: MAJOR.; HELP = The Image loaded does not contain E1 code.\ Load a new Image that includes E1 code, or \ consult with the System Admin. or Field \ Personnel.;
TRAP-TYPE    

mcm4400E1DownloadFail 14
NAME = ; DESC = Indicates a failure occurred during the E1 \ code download.\ Severity Level: MAJOR. ; HELP = Retry the download. Re-boot the access device and \ check if it downloads correctly. Also, verify \ the E1 code that is built with access device \ image is the right version. If problem persist, \ consult your system admin., or field personnel.;
TRAP-TYPE    

mcm4400E1OutOfOrder 15
NAME = ; DESC = Indicates the E1 is not responding.\ Severity Level: CRITICAL.; HELP = Management frame is out of order. Check for \ Framing error. If it does not recover, Please \ contact your Sys Admin. or Field personnel.;
TRAP-TYPE    

mcm4400E1OutOfOrderRecovered 16
NAME = ; DESC = Indicates recovery from the E1 out of order condition.\ Severity Level: INFORMATIVE.; HELP = E1 is responding. Normal Status Indicator.;
TRAP-TYPE    

mcm4400E1FailToSyncUp 17
NAME = ; DESC = Indicates the E1 is unable to sync up.\ Severity Level: CRITICAL.; HELP = Check the physical connection locally, and \ to the remote device. Possible protocol error. \ If problem still persist, contact your \ system admin., or field personnel.;
TRAP-TYPE    

mcm4400E1FailToSyncUpRecovered 18
NAME = ; DESC = Indicates recovery from the E1 failure \ to sync up condition.\ Severity Level: INFORMATIVE.; HELP = E1 has recovered. Normal Status Indicator.;
TRAP-TYPE    

mcm4400E1AISAlarmSet 19
NAME = ; DESC = Indicates an E1 AIS Alarm condition is present.\ Severity Level: MAJOR.; HELP = Check physical link of the local E1, and the Remote \ PBX. Possible Framing error. If problem is not \ resolved, contact sys admin., or field personnel.;
TRAP-TYPE    

mcm4400E1AISAlarmClear 20
NAME = ; DESC = Indicates an E1 AIS Alarm condition has cleared.\ Severity Level: INFORMATIVE. ; HELP = E1 AIS Alarm is cleared. Normal Status Indicator.;
TRAP-TYPE    

mcm4400E1RedAlarmSet 21
NAME = ; DESC = Indicates an E1 Red Alarm condition is present.\ Severity Level: MAJOR.; HELP = Check the Physical Connection to remote. \ Run a loopback test and determine the problem. \ If the Alarm condition is still persistant, \ contact your Field Personnel.;
TRAP-TYPE    

mcm4400E1RedAlarmClear 22
NAME = ; DESC = Indicates an E1 Red Alarm condition has cleared.\ Severity Level: INFORMATIVE.; HELP = Red Alarm Cleared. Normal Status Indicator!.;
TRAP-TYPE    

mcm4400E1TS16AISAlarmSet 23
NAME = ; DESC = Indicates an E1 TS16 AIS Alarm is present.\ Severity Level: MAJOR.; HELP = TX or RX side for physical connection may be faulty; \ Possible Framing error with Remote device. Run Loopback \ test if possible, & determine the problem. If that does not\ help, please contact Field Personnel or System admin.;
TRAP-TYPE    

mcm4400E1TS16AISAlarmClear 24
NAME = ; DESC = Indicates an E1 TS16 AIS Alarm has cleared.\ Severity Level: INFORMATIVE.; HELP = Alarm is cleared. Normal Status Indicator!.;
TRAP-TYPE    

mcm4400E1OOSMFAlarmSet 25
NAME = ; DESC = Indicates an E1 00SMF Alarm is present.\ Severity Level: MAJOR.; HELP = Framing error due to signal loss. Run Loopback \ test and determine the problem. For further help \ contact your Field Personnel.;
TRAP-TYPE    

mcm4400E1OOSMFAlarmClear 26
NAME = ; DESC = Indicates an E1 00SMF Alarm has cleared.\ Severity Level: INFORMATIVE.; HELP = OOSMF Alarm is cleared. Normal Status Indicator!.;
TRAP-TYPE    

mcm4400E1RemoteYBitAlarmSet 27
NAME = ; DESC = Indicates an E1 Remote Y Bit Alarm is present.\ Severity Level: MAJOR.; HELP = Run Loopback test, and determine the condition. \ For further help, contact Field Personnel.;
TRAP-TYPE    

mcm4400E1RemoteYBitAlarmClear 28
NAME = ; DESC = Indicates an E1 Remote Y Bit Alarm has cleared.\ Severity Level: INFORMATIVE.; HELP = Remote YBit Alarm is cleared. Normal Status \ Indicator.;
TRAP-TYPE    

mcm4400E1RemoteABitAlarmSet 29
NAME = ; DESC = Indicates an E1 Remote A Bit Alarm is present.\ Severity Level: MAJOR.; HELP = Possible frame Error. Please run loopback test \ and determine the condition. If Alarm \ is not cleared, contact your Field Personnel.;
TRAP-TYPE    

mcm4400E1RemoteABitAlarmClear 30
NAME = ; DESC = Indicates an E1 Remote Y Bit Alarm has cleared.\ Severity Level: INFORMATIVE.; HELP = Alarm is cleared. Normal Status Indicator!.;
TRAP-TYPE    

mcm4400E1OOCMFAlarmSet 31
NAME = ; DESC = Indicates an E1 00CMF Alarm is present.\ Severity Level: MAJOR.; HELP = CRC multframe alignment is lost. Run loobback \ test and determine the problem. For further \ help, contact Field Personnel. ;
TRAP-TYPE    

mcm4400E1OOCMFAlarmClear 32
NAME = ; DESC = Indicates an E1 00CMF Alarm has cleared.\ Severity Level: INFORMATIVE.; HELP = OOCMF Alarm is cleared. Normal Status Indicator.;
TRAP-TYPE