ME1200-ACL-MIB

File: ME1200-ACL-MIB.mib (111903 bytes)

Imported modules

SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
CISCOME1200-MIB INET-ADDRESS-MIB ME1200-TC

Imported symbols

MODULE-COMPLIANCE OBJECT-GROUP MODULE-IDENTITY
OBJECT-TYPE TEXTUAL-CONVENTION me1200SwitchMgmt
InetAddressIPv6 ME1200InterfaceIndex ME1200PortList
ME1200RowEditorState ME1200Unsigned16 ME1200Unsigned8
Integer32 IpAddress Unsigned32
MacAddress TruthValue

Defined Types

ME1200ASRType  
Represents an Any/Specific/Range selector.
TEXTUAL-CONVENTION    
  INTEGER any(0), specific(1), range(2)  

ME1200ASType  
Represents an Any/Specific selector.
TEXTUAL-CONVENTION    
  INTEGER any(0), specific(1)  

ME1200AclAceFlagOpcode  
ACL ACE flag opcode.
TEXTUAL-CONVENTION    
  INTEGER any(0), notequal(1), equal(2)  

ME1200AclAceHitAction  
The hit action of the ACE.
TEXTUAL-CONVENTION    
  INTEGER deny(0), permit(1), filter(2)  

ME1200AclAceType  
The frame type of the ACE.
TEXTUAL-CONVENTION    
  INTEGER any(0), etype(1), arp(4), ipv4(5), ipv6(6)  

ME1200AclInterfaceHitAction  
The hit action of the interface.
TEXTUAL-CONVENTION    
  INTEGER deny(0), permit(1)  

ME1200AclUser  
ACL user.
TEXTUAL-CONVENTION    
  INTEGER static(0), ipSourceGuard(1), ipmc(2), evc(3), mep(4), arpInspection(5), upnp(6), ptp(7), dhcp(8), loopProtect(9), linkOam(10), ztp(11), ttLoop(12), y1564(13)  

ME1200AdvDestMacType  
Represents a destination MAC type selector.
TEXTUAL-CONVENTION    
  INTEGER any(0), unicast(1), multicast(2), broadcast(3), specific(4)  

ME1200ArpOpcode  
ARP opcode.
TEXTUAL-CONVENTION    
  INTEGER any(0), arp(1), rarp(2), other(3)  

ME1200DestMacType  
Represents a destination MAC type selector.
TEXTUAL-CONVENTION    
  INTEGER any(0), unicast(1), multicast(2), broadcast(3)  

ME1200VlanTagPriority  
VLAN priority.
TEXTUAL-CONVENTION    
  INTEGER any(0), value0(1), value1(2), value2(3), value3(4), value4(5), value5(6), value6(7), value7(8), range0to1(9), range2to3(10), range4to5(11), range6to7(12), range0to3(13), range4to7(14)  

ME1200VlanTagged  
VLAN tagged/untagged.
TEXTUAL-CONVENTION    
  INTEGER any(0), untagged(1), tagged(2)  

ME1200AclRateLimiterEntry  
SEQUENCE    
  me1200AclRateLimiterId Integer32
  me1200AclRateLimiterPacketRate Unsigned32
  me1200AclRateLimiterBitRate Unsigned32
  me1200AclRateLimiterBitRateEnable TruthValue

ME1200AclAceEntry  
SEQUENCE    
  me1200AclAceId Integer32
  me1200AclAceNextAceId Unsigned32
  me1200AclAceLookup TruthValue
  me1200AclAceIngressPortList ME1200PortList
  me1200AclAcePolicyValue ME1200Unsigned8
  me1200AclAcePolicyMask ME1200Unsigned8
  me1200AclAceHitAction ME1200AclAceHitAction
  me1200AclAceFilterPortList ME1200PortList
  me1200AclAceRateLimiterId Unsigned32
  me1200AclAceEvcPolicerId ME1200Unsigned16
  me1200AclAceRedirectPortList ME1200PortList
  me1200AclAceMirror TruthValue
  me1200AclAceLogging TruthValue
  me1200AclAceShutdown TruthValue
  me1200AclAceVlanTagged ME1200VlanTagged
  me1200AclAceVlanId ME1200Unsigned16
  me1200AclAceVlanTagPriority ME1200VlanTagPriority
  me1200AclAceFrameType ME1200AclAceType
  me1200AclAceEtypeSrcMacOp ME1200ASType
  me1200AclAceEtypeSrcMac MacAddress
  me1200AclAceEtypeDestMacOp ME1200AdvDestMacType
  me1200AclAceEtypeDestMac MacAddress
  me1200AclAceEtype ME1200Unsigned16
  me1200AclAceArpSrcMacOp ME1200ASType
  me1200AclAceArpSrcMac MacAddress
  me1200AclAceArpDestMacOp ME1200DestMacType
  me1200AclAceArpSenderIp IpAddress
  me1200AclAceArpSenderIpMask IpAddress
  me1200AclAceArpTragetIp IpAddress
  me1200AclAceArpTragetIpMask IpAddress
  me1200AclAceArpOpcode ME1200ArpOpcode
  me1200AclAceArpFlagRequest ME1200AclAceFlagOpcode
  me1200AclAceArpFlagSenderMac ME1200AclAceFlagOpcode
  me1200AclAceArpFlagTargetMac ME1200AclAceFlagOpcode
  me1200AclAceArpFlagLen ME1200AclAceFlagOpcode
  me1200AclAceArpFlagIp ME1200AclAceFlagOpcode
  me1200AclAceArpFlagEthernet ME1200AclAceFlagOpcode
  me1200AclAceIpv4DestMacOp ME1200DestMacType
  me1200AclAceIpv4ProtocolOp ME1200ASType
  me1200AclAceIpv4Protocol ME1200Unsigned8
  me1200AclAceIpv4FlagTtl ME1200AclAceFlagOpcode
  me1200AclAceIpv4FlagFragment ME1200AclAceFlagOpcode
  me1200AclAceIpv4FlagIpOption ME1200AclAceFlagOpcode
  me1200AclAceIpv4SrcIp IpAddress
  me1200AclAceIpv4SrcIpMask IpAddress
  me1200AclAceIpv4DestIp IpAddress
  me1200AclAceIpv4DestIpMask IpAddress
  me1200AclAceIpv4IcmpTypeOp ME1200ASType
  me1200AclAceIpv4IcmpType ME1200Unsigned8
  me1200AclAceIpv4IcmpCodeOp ME1200ASType
  me1200AclAceIpv4IcmpCode ME1200Unsigned8
  me1200AclAceIpv4SrcPortOp ME1200ASRType
  me1200AclAceIpv4SrcPort ME1200Unsigned16
  me1200AclAceIpv4SrcPortRange ME1200Unsigned16
  me1200AclAceIpv4DestPortOp ME1200ASRType
  me1200AclAceIpv4DestPort ME1200Unsigned16
  me1200AclAceIpv4DestPortRange ME1200Unsigned16
  me1200AclAceIpv4TcpFlagFin ME1200AclAceFlagOpcode
  me1200AclAceIpv4TcpFlagSyn ME1200AclAceFlagOpcode
  me1200AclAceIpv4TcpFlagRst ME1200AclAceFlagOpcode
  me1200AclAceIpv4TcpFlagPsh ME1200AclAceFlagOpcode
  me1200AclAceIpv4TcpFlagAck ME1200AclAceFlagOpcode
  me1200AclAceIpv4TcpFlagUrg ME1200AclAceFlagOpcode
  me1200AclAceIPv6DestMacOp ME1200DestMacType
  me1200AclAceIpv6NextHeaderOp ME1200ASType
  me1200AclAceIpv6NextHeader ME1200Unsigned8
  me1200AclAceIpv6SrcIp InetAddressIPv6
  me1200AclAceIpv6SrcIpMask InetAddressIPv6
  me1200AclAceIpv6FlagHopLimiter ME1200AclAceFlagOpcode
  me1200AclAceIpv6Icmpv6TypeOp ME1200ASType
  me1200AclAceIpv6Icmpv6Type ME1200Unsigned8
  me1200AclAceIpv6Icmpv6CodeOp ME1200ASType
  me1200AclAceIpv6Icmpv6Code ME1200Unsigned8
  me1200AclAceIpv6SrcPortOp ME1200ASRType
  me1200AclAceIpv6SrcPort ME1200Unsigned16
  me1200AclAceIpv6SrcPortRange ME1200Unsigned16
  me1200AclAceIpv6DestPortOp ME1200ASRType
  me1200AclAceIpv6DestPort ME1200Unsigned16
  me1200AclAceIpv6DestPortRange ME1200Unsigned16
  me1200AclAceIpv6TcpFlagFin ME1200AclAceFlagOpcode
  me1200AclAceIpv6TcpFlagSyn ME1200AclAceFlagOpcode
  me1200AclAceIpv6TcpFlagRst ME1200AclAceFlagOpcode
  me1200AclAceIpv6TcpFlagPsh ME1200AclAceFlagOpcode
  me1200AclAceIpv6TcpFlagAck ME1200AclAceFlagOpcode
  me1200AclAceIpv6TcpFlagUrg ME1200AclAceFlagOpcode
  me1200AclAceAction ME1200RowEditorState

ME1200AclAcePrecedenceEntry  
SEQUENCE    
  me1200AclAcePrecedencePrecedenceIndex Integer32
  me1200AclAcePrecedenceAceId Unsigned32

ME1200AclInterfaceEntry  
SEQUENCE    
  me1200AclInterfaceIfIndex ME1200InterfaceIndex
  me1200AclInterfacePolicyId Unsigned32
  me1200AclInterfaceHitAction ME1200AclInterfaceHitAction
  me1200AclInterfaceRateLimiterId Unsigned32
  me1200AclInterfaceEvcPolicerId ME1200Unsigned16
  me1200AclInterfaceRedirectPortList ME1200PortList
  me1200AclInterfaceMirror TruthValue
  me1200AclInterfaceLogging TruthValue
  me1200AclInterfaceShutdown TruthValue
  me1200AclInterfaceState TruthValue

ME1200AclAceStatusEntry  
SEQUENCE    
  me1200AclAceStatusPrecedenceIndex Integer32
  me1200AclAceStatusUser ME1200AclUser
  me1200AclAceStatusAceId Unsigned32
  me1200AclAceStatusConflict TruthValue

ME1200AclAceHitCountEntry  
SEQUENCE    
  me1200AclAceHitCountAceId Integer32
  me1200AclAceHitCountHitCount Unsigned32

ME1200AclInterfaceHitCountEntry  
SEQUENCE    
  me1200AclInterfaceHitCountId Integer32
  me1200AclInterfaceHitCountHitCount Unsigned32

Defined Values

me1200AclMIB 1.3.6.1.4.1.9.9.815.1.17
This is a private MIB for ACL
MODULE-IDENTITY    

me1200AclMIBObjects 1.3.6.1.4.1.9.9.815.1.17.1
OBJECT IDENTIFIER    

me1200AclConfig 1.3.6.1.4.1.9.9.815.1.17.1.2
OBJECT IDENTIFIER    

me1200AclGlobals 1.3.6.1.4.1.9.9.815.1.17.1.2.1
OBJECT IDENTIFIER    

me1200AclRateLimiterTable 1.3.6.1.4.1.9.9.815.1.17.1.2.1.1
The ACL rate limiter configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ME1200AclRateLimiterEntry

me1200AclRateLimiterEntry 1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1
Each rate limiter ID has a set of parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  ME1200AclRateLimiterEntry  

me1200AclRateLimiterId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.1
The identification of ACL rate limter.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

me1200AclRateLimiterPacketRate 1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.2
The packet rate per second. The operation is inactive when bit rate mode is enabled. Possible values are: 0-99, 100, 2*100, 3*100..., 1092000.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

me1200AclRateLimiterBitRate 1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.3
The bit rate per second.The operation is inactive when bit rate mode is disabled. Possible values are: 0, 100, 2*100, 3*100, ..., 1000000.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

me1200AclRateLimiterBitRateEnable 1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.4
Enable bit rate.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAce 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2
OBJECT IDENTIFIER    

me1200AclAceTable 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1
The ACL ACE configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ME1200AclAceEntry

me1200AclAceEntry 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1
Each row contains a set of parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  ME1200AclAceEntry  

me1200AclAceId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.1
The identification of ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

me1200AclAceNextAceId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.2
The next identification for this ACE. Possible values are: 0(end of list), 1-512.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

me1200AclAceLookup 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.3
The second lookup operation for this ACE. Possible values are: 1(enabled) and 2(disabled).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAceIngressPortList 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.5
The ingress port list for this ACE. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200PortList  

me1200AclAcePolicyValue 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.6
The policy number for this ACE. The feature is inactive when policy mask value is non-zero.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAcePolicyMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.7
The policy number for this ACE. The feature is inactive when policy mask value is non-zero.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceHitAction 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.8
The hit action operation for this ACE. Note all ports will be the filter port member when filter action is set on the first time.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceHitAction  

me1200AclAceFilterPortList 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.9
The filter port list. It is active only when the hit action is filtered. Set the action value to 0(filter) before the new setting. Note that the action will change deny action if there is no any port in the member set. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200PortList  

me1200AclAceRateLimiterId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.10
The rate limiter ID. Possible values are: 0(disabled), 1-16.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

me1200AclAceEvcPolicerId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.11
The EVC policer ID. Possible values are: 0(disabled), 1-1022.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceRedirectPortList 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.12
The ingress port list for this ACE. It is active only when the hit action is denied. Set the action value to 1(deny) before the new setting. Set value 0 to disable the opertion. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200PortList  

me1200AclAceMirror 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.13
The rmirror operation. Frames matching this ACE are mirrored to the destination mirror port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAceLogging 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.14
The logging operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAceShutdown 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.15
The shutdown operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAceVlanTagged 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.100
The 802.1Q VLAN tagged for this ACE.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200VlanTagged  

me1200AclAceVlanId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.101
The VLAN ID for this ACE. Possible values are: 0(disabled), 1-4095.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceVlanTagPriority 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.102
The VLN tag priority for this ACE. Enable VLAN tagged filter before the new setting.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200VlanTagPriority  

me1200AclAceFrameType 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.200
The frame type for this ACE.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceType  

me1200AclAceEtypeSrcMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.300
Indicates how a Ethernet type packet's source MAC address is to be compared. This object can only be configured if FrameType is etype(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceEtypeSrcMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.301
Indicates the 48 bits source MAC address. This object can only be configured if FrameType is etype(1) and EtypeSrcMacOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

me1200AclAceEtypeDestMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.302
Indicates how a Ethernet type packet's destination MAC address is to be compared. This object can only be configured if FrameType is etype(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AdvDestMacType  

me1200AclAceEtypeDestMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.303
Indicates the 48 bits destination MAC address. This object can only be configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

me1200AclAceEtype 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.304
Indicates the packet's 16 bit Ethernet type field. Possible values are: 0(disabled), 0x600-0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and 0x86DD(IPv6).This object can only be configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceArpSrcMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.600
Indicates how a ARP packet's source MAC address is to be compared. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceArpSrcMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.601
Indicates the 48 bits source MAC address. This object can only be configured if FrameType is arp(4) and ArpSrcMacOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

me1200AclAceArpDestMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.602
Indicates how a ARP packet's destination MAC address is to be compared. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200DestMacType  

me1200AclAceArpSenderIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.603
The specified ARP sender IP address. The packets sender address is AND-ed with the value of ArpSenderIpMask and then compared with the value of this object. If ArpSenderIp and ArpSrcIpMask are 0.0.0.0, this entry matches any sender IP address. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceArpSenderIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.604
The specified ARP sender IP address mask. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceArpTragetIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.605
The specified ARP target IP address. The packets target address is AND-ed with the value of ArpTragetIpMask and then compared with the value of this object. If ArpTragetIp and ArpSrcIpMask are 0.0.0.0, this entry matches any target IP address. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceArpTragetIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.606
The specified ARP target IP address mask. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceArpOpcode 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.607
Indicates how a ARP packet's opcode is to be compared. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ArpOpcode  

me1200AclAceArpFlagRequest 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.608
Indicates how a ARP packet's request/reply opcode is to be compared. The value 0 means any ARP opcode is allowed (don't-care field), value 1 means ARP opcode is equal to request opcode and value 2 means ARP opcode is equal to reply opcode. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceArpFlagSenderMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.609
Indicates how a ARP packet's sender hardware address field (SHA) is to be compared. The value 0 means any SHA value is allowed (don't-care field), value 1 means SHA is not equal to the SMAC address and value 2 means SHA is equal to the SMAC address. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceArpFlagTargetMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.610
Indicates how a ARP packet's target hardware address field (THA) is to be compared. The value 0 means any THA value is allowed (don't-care field), value 1 means THA is not equal to the DMAC address and value 2 means THA is equal to the DMAC address. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceArpFlagLen 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.611
Indicates how a ARP packet's s hardware address length field (HLN) is to be compared. The value 0 means any HLN value is allowed (don't-care field), value 1 means HLN is not equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04) and value 2 means HLN is equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04). This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceArpFlagIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.612
Indicates how a ARP packet's hardware address space field (HRD) is to be compared. The value 0 means any HRD value is allowed (don't-care field), value 1 means HRD is not equal to Ethernet (1) and value 2 means HRD is equal to Ethernet (1). This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceArpFlagEthernet 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.613
Indicates how a ARP packet's protocol address space field (PRO) is to be compared. The value 0 means any PRO value is allowed (don't-care field), value 1 means PRO is not equal to IP (0x800) and value 2 means PRO is equal to IP (0x800). This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4DestMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.700
Indicates how a IPv4 packet's destination MAC address is to be compared. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200DestMacType  

me1200AclAceIpv4ProtocolOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.701
Indicates how a IPv4 packet's protocol field is to be compared. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceIpv4Protocol 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.702
The protocol number field in the IPv4 header used to indicate a higher layer protocol. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceIpv4FlagTtl 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.703
Indicates how a IPv4 packet's Time-to-Live field (TTL) is to be compared. The value 0 means any TTL value is allowed (don't-care field), value 1 means TTL is not equal zero and value 2 means TTL is equal to zero. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4FlagFragment 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.704
Indicates how a IPv4 packet's More-Fragments field (MF) is to be compared. The value 0 means any MF value is allowed (don't-care field), value 1 means MF is not equal one (MF field isn't set) and value 2 means MF is equal to one (MF field is set). This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4FlagIpOption 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.705
Indicates how a IPv4 packet's options field is to be compared. The value 0 means any options is allowed (don't-care field), value 1 means options is not equal one (options field isn't set) and value 2 means options is equal to one (options field is set). This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4SrcIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.706
The specified source IPv4 address. The packets sender address is AND-ed with the value of Ipv4SrcIpMask and then compared with the value of this object. If Ipv4SrcIp and Ipv4SrcIpMask are 0.0.0.0, this entry matches any source IP address. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceIpv4SrcIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.707
The specified source IPv4 address mask. This object can only be configured if FrameType isipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceIpv4DestIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.708
The specified destination IPv4 address. The packets sender address is AND-ed with the value of Ipv4DestIpMask and then compared with the value of this object. If Ipv4DestIp and Ipv4DestIpMask are 0.0.0.0, this entry matches any destination IP address. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceIpv4DestIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.709
The specified destination IPv4 address mask. This object can only be configured if FrameType isipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceIpv4IcmpTypeOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.710
Indicates how a IPv4 packet's ICMP type field is to be compared. This object can only be configured if FrameType is ipv4(5) and Ipv4Protocol is icmp(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceIpv4IcmpType 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.711
The ICMP type field in the IPv4 header. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5), Ipv4Protocol is icmp(1) and Ipv4IcmpTypeOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceIpv4IcmpCodeOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.712
Indicates how a IPv4 packet's ICMP code field is to be compared. This object can only be configured if FrameType is ipv4(5) and Ipv4Protocol is icmp(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceIpv4IcmpCode 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.713
The ICMP code field in the IPv4 header. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5), Ipv4Protocol is icmp(1) and Ipv4IcmpCodeOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceIpv4SrcPortOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.714
Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASRType  

me1200AclAceIpv4SrcPort 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.715
The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is not any(0).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceIpv4SrcPortRange 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.716
The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is range(2).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceIpv4DestPortOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.717
Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASRType  

me1200AclAceIpv4DestPort 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.718
The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4DestPortOp is not any(0).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceIpv4DestPortRange 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.719
The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4DestPortOp is range(2).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceIpv4TcpFlagFin 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.720
Indicates how a IPv4 TCP packet's 'No more data from sender' field (FIN) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means FIN is not equal one (FIN field isn't set) and value 2 means FIN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4TcpFlagSyn 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.721
Indicates how a IPv4 TCP packet's 'Synchronize sequence numbers' field (SYN) is to be compared. The value 0 means any SYN value is allowed (don't-care field), value 1 means SYN is not equal one (FIN field isn't set) and value 2 means SYN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4TcpFlagRst 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.722
Indicates how a IPv4 TCP packet's 'Reset the connection' field (RST) is to be compared. The value 0 means any RST value is allowed (don't-care field), value 1 means RST is not equal one (FIN field isn't set) and value 2 means RST is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4TcpFlagPsh 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.723
Indicates how a IPv4 TCP packet's 'Push Function' field (PSH) is to be compared. The value 0 means any PSH value is allowed (don't-care field), value 1 means PSH is not equal one (FIN field isn't set) and value 2 means PSH is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4TcpFlagAck 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.724
Indicates how a IPv4 TCP packet's 'Acknowledgment field significant' field (ACK) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means ACK is not equal one (FIN field isn't set) and value 2 means ACK is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv4TcpFlagUrg 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.725
Indicates how a IPv4 TCP packet's 'Urgent Pointer field significant' field (URG) is to be compared. The value 0 means any URG value is allowed (don't-care field), value 1 means URG is not equal one (FIN field isn't set) and value 2 means URG is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIPv6DestMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.800
Indicates how a IPv6 packet's destination MAC address is to be compared. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200DestMacType  

me1200AclAceIpv6NextHeaderOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.801
Indicates how a IPv6 packet's next header field is to be compared. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceIpv6NextHeader 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.802
The next header field in the IPv6 header used to indicate a higher layer protocol. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeaderOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceIpv6SrcIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.803
The specified IPv6 source address. The packets source address is AND-ed with the value of Ipv6SrcIpMask and then compared with the value of this object. If Ipv6SrcIp and Ipv6SrcIpMask are all zeros, this entry matches any IPv6 source address. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcIpMask is not all zeros.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressIPv6  

me1200AclAceIpv6SrcIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.804
The specified IPv6 source address mask. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressIPv6  

me1200AclAceIpv6FlagHopLimiter 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.805
Indicates how a IPv6 packet's hop limit field is to be compared. The value 0 means any hop limit value is allowed (don't-care field), value 1 means hop limit is not equal zero and value 2 means hop limit is equal to zero. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv6Icmpv6TypeOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.806
Indicates how a IPv6 packet's ICMPv6 type field is to be compared. This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeader is icmpv6(58).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceIpv6Icmpv6Type 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.807
The ICMPv6 type field in the IPv6 header. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6), Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6TypeOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceIpv6Icmpv6CodeOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.808
Indicates how a IPv6 packet's ICMPv6 code field is to be compared. This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeader is icmpv6(58).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceIpv6Icmpv6Code 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.809
The ICMPv6 code field in the IPv6 header. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6), Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6CodeOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceIpv6SrcPortOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.810
Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASRType  

me1200AclAceIpv6SrcPort 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.811
The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is not any(0).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceIpv6SrcPortRange 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.812
The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is range(2).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceIpv6DestPortOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.813
Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASRType  

me1200AclAceIpv6DestPort 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.814
The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6DestPortOp is not any(0).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceIpv6DestPortRange 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.815
The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6DestPortOp is range(2).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceIpv6TcpFlagFin 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.816
Indicates how a IPv6 TCP packet's 'No more data from sender' field (FIN) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means FIN is not equal one (FIN field isn't set) and value 2 means FIN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv6TcpFlagSyn 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.817
Indicates how a IPv6 TCP packet's 'Synchronize sequence numbers' field (SYN) is to be compared. The value 0 means any SYN value is allowed (don't-care field), value 1 means SYN is not equal one (FIN field isn't set) and value 2 means SYN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv6TcpFlagRst 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.818
Indicates how a IPv6 TCP packet's 'Reset the connection' field (RST) is to be compared. The value 0 means any RST value is allowed (don't-care field), value 1 means RST is not equal one (FIN field isn't set) and value 2 means RST is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv6TcpFlagPsh 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.819
Indicates how a IPv6 TCP packet's 'Push Function' field (PSH) is to be compared. The value 0 means any PSH value is allowed (don't-care field), value 1 means PSH is not equal one (FIN field isn't set) and value 2 means PSH is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv6TcpFlagAck 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.820
Indicates how a IPv6 TCP packet's 'Acknowledgment field significant' field (ACK) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means ACK is not equal one (FIN field isn't set) and value 2 means ACK is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceIpv6TcpFlagUrg 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.821
Indicates how a IPv6 TCP packet's 'Urgent Pointer field significant' field (URG) is to be compared. The value 0 means any URG value is allowed (don't-care field), value 1 means URG is not equal one (FIN field isn't set) and value 2 means URG is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceAction 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.1000
Action
Status: current Access: read-write
OBJECT-TYPE    
  ME1200RowEditorState  

me1200AclAceTableRowEditor 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2
OBJECT IDENTIFIER    

me1200AclAceTableRowEditorId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.1
The identification of ACE.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..2147483647  

me1200AclAceTableRowEditorNextAceId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.2
The next identification for this ACE. Possible values are: 0(end of list), 1-512.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

me1200AclAceTableRowEditorLookup 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.3
The second lookup operation for this ACE. Possible values are: 1(enabled) and 2(disabled).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAceTableRowEditorIngressPortList 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.5
The ingress port list for this ACE. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200PortList  

me1200AclAceTableRowEditorPolicyValue 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.6
The policy number for this ACE. The feature is inactive when policy mask value is non-zero.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceTableRowEditorPolicyMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.7
The policy number for this ACE. The feature is inactive when policy mask value is non-zero.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceTableRowEditorHitAction 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.8
The hit action operation for this ACE. Note all ports will be the filter port member when filter action is set on the first time.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceHitAction  

me1200AclAceTableRowEditorFilterPortList 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.9
The filter port list. It is active only when the hit action is filtered. Set the action value to 0(filter) before the new setting. Note that the action will change deny action if there is no any port in the member set. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200PortList  

me1200AclAceTableRowEditorRateLimiterId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.10
The rate limiter ID. Possible values are: 0(disabled), 1-16.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

me1200AclAceTableRowEditorEvcPolicerId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.11
The EVC policer ID. Possible values are: 0(disabled), 1-1022.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorRedirectPortList 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.12
The ingress port list for this ACE. It is active only when the hit action is denied. Set the action value to 1(deny) before the new setting. Set value 0 to disable the opertion. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200PortList  

me1200AclAceTableRowEditorMirror 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.13
The rmirror operation. Frames matching this ACE are mirrored to the destination mirror port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAceTableRowEditorLogging 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.14
The logging operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAceTableRowEditorShutdown 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.15
The shutdown operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclAceTableRowEditorVlanTagged 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.100
The 802.1Q VLAN tagged for this ACE.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200VlanTagged  

me1200AclAceTableRowEditorVlanId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.101
The VLAN ID for this ACE. Possible values are: 0(disabled), 1-4095.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorVlanTagPriority 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.102
The VLN tag priority for this ACE. Enable VLAN tagged filter before the new setting.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200VlanTagPriority  

me1200AclAceTableRowEditorFrameType 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.200
The frame type for this ACE.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceType  

me1200AclAceTableRowEditorEtypeSrcMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.300
Indicates how a Ethernet type packet's source MAC address is to be compared. This object can only be configured if FrameType is etype(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceTableRowEditorEtypeSrcMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.301
Indicates the 48 bits source MAC address. This object can only be configured if FrameType is etype(1) and EtypeSrcMacOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

me1200AclAceTableRowEditorEtypeDestMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.302
Indicates how a Ethernet type packet's destination MAC address is to be compared. This object can only be configured if FrameType is etype(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AdvDestMacType  

me1200AclAceTableRowEditorEtypeDestMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.303
Indicates the 48 bits destination MAC address. This object can only be configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

me1200AclAceTableRowEditorEtype 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.304
Indicates the packet's 16 bit Ethernet type field. Possible values are: 0(disabled), 0x600-0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and 0x86DD(IPv6).This object can only be configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorArpSrcMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.600
Indicates how a ARP packet's source MAC address is to be compared. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceTableRowEditorArpSrcMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.601
Indicates the 48 bits source MAC address. This object can only be configured if FrameType is arp(4) and ArpSrcMacOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

me1200AclAceTableRowEditorArpDestMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.602
Indicates how a ARP packet's destination MAC address is to be compared. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200DestMacType  

me1200AclAceTableRowEditorArpSenderIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.603
The specified ARP sender IP address. The packets sender address is AND-ed with the value of ArpSenderIpMask and then compared with the value of this object. If ArpSenderIp and ArpSrcIpMask are 0.0.0.0, this entry matches any sender IP address. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceTableRowEditorArpSenderIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.604
The specified ARP sender IP address mask. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceTableRowEditorArpTragetIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.605
The specified ARP target IP address. The packets target address is AND-ed with the value of ArpTragetIpMask and then compared with the value of this object. If ArpTragetIp and ArpSrcIpMask are 0.0.0.0, this entry matches any target IP address. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceTableRowEditorArpTragetIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.606
The specified ARP target IP address mask. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceTableRowEditorArpOpcode 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.607
Indicates how a ARP packet's opcode is to be compared. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ArpOpcode  

me1200AclAceTableRowEditorArpFlagRequest 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.608
Indicates how a ARP packet's request/reply opcode is to be compared. The value 0 means any ARP opcode is allowed (don't-care field), value 1 means ARP opcode is equal to request opcode and value 2 means ARP opcode is equal to reply opcode. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorArpFlagSenderMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.609
Indicates how a ARP packet's sender hardware address field (SHA) is to be compared. The value 0 means any SHA value is allowed (don't-care field), value 1 means SHA is not equal to the SMAC address and value 2 means SHA is equal to the SMAC address. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorArpFlagTargetMac 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.610
Indicates how a ARP packet's target hardware address field (THA) is to be compared. The value 0 means any THA value is allowed (don't-care field), value 1 means THA is not equal to the DMAC address and value 2 means THA is equal to the DMAC address. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorArpFlagLen 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.611
Indicates how a ARP packet's s hardware address length field (HLN) is to be compared. The value 0 means any HLN value is allowed (don't-care field), value 1 means HLN is not equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04) and value 2 means HLN is equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04). This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorArpFlagIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.612
Indicates how a ARP packet's hardware address space field (HRD) is to be compared. The value 0 means any HRD value is allowed (don't-care field), value 1 means HRD is not equal to Ethernet (1) and value 2 means HRD is equal to Ethernet (1). This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorArpFlagEthernet 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.613
Indicates how a ARP packet's protocol address space field (PRO) is to be compared. The value 0 means any PRO value is allowed (don't-care field), value 1 means PRO is not equal to IP (0x800) and value 2 means PRO is equal to IP (0x800). This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4DestMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.700
Indicates how a IPv4 packet's destination MAC address is to be compared. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200DestMacType  

me1200AclAceTableRowEditorIpv4ProtocolOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.701
Indicates how a IPv4 packet's protocol field is to be compared. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceTableRowEditorIpv4Protocol 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.702
The protocol number field in the IPv4 header used to indicate a higher layer protocol. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceTableRowEditorIpv4FlagTtl 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.703
Indicates how a IPv4 packet's Time-to-Live field (TTL) is to be compared. The value 0 means any TTL value is allowed (don't-care field), value 1 means TTL is not equal zero and value 2 means TTL is equal to zero. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4FlagFragment 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.704
Indicates how a IPv4 packet's More-Fragments field (MF) is to be compared. The value 0 means any MF value is allowed (don't-care field), value 1 means MF is not equal one (MF field isn't set) and value 2 means MF is equal to one (MF field is set). This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4FlagIpOption 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.705
Indicates how a IPv4 packet's options field is to be compared. The value 0 means any options is allowed (don't-care field), value 1 means options is not equal one (options field isn't set) and value 2 means options is equal to one (options field is set). This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4SrcIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.706
The specified source IPv4 address. The packets sender address is AND-ed with the value of Ipv4SrcIpMask and then compared with the value of this object. If Ipv4SrcIp and Ipv4SrcIpMask are 0.0.0.0, this entry matches any source IP address. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceTableRowEditorIpv4SrcIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.707
The specified source IPv4 address mask. This object can only be configured if FrameType isipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceTableRowEditorIpv4DestIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.708
The specified destination IPv4 address. The packets sender address is AND-ed with the value of Ipv4DestIpMask and then compared with the value of this object. If Ipv4DestIp and Ipv4DestIpMask are 0.0.0.0, this entry matches any destination IP address. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceTableRowEditorIpv4DestIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.709
The specified destination IPv4 address mask. This object can only be configured if FrameType isipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

me1200AclAceTableRowEditorIpv4IcmpTypeOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.710
Indicates how a IPv4 packet's ICMP type field is to be compared. This object can only be configured if FrameType is ipv4(5) and Ipv4Protocol is icmp(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceTableRowEditorIpv4IcmpType 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.711
The ICMP type field in the IPv4 header. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5), Ipv4Protocol is icmp(1) and Ipv4IcmpTypeOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceTableRowEditorIpv4IcmpCodeOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.712
Indicates how a IPv4 packet's ICMP code field is to be compared. This object can only be configured if FrameType is ipv4(5) and Ipv4Protocol is icmp(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceTableRowEditorIpv4IcmpCode 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.713
The ICMP code field in the IPv4 header. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5), Ipv4Protocol is icmp(1) and Ipv4IcmpCodeOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceTableRowEditorIpv4SrcPortOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.714
Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASRType  

me1200AclAceTableRowEditorIpv4SrcPort 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.715
The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is not any(0).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorIpv4SrcPortRange 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.716
The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is range(2).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorIpv4DestPortOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.717
Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(5).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASRType  

me1200AclAceTableRowEditorIpv4DestPort 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.718
The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4DestPortOp is not any(0).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorIpv4DestPortRange 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.719
The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4DestPortOp is range(2).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorIpv4TcpFlagFin 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.720
Indicates how a IPv4 TCP packet's 'No more data from sender' field (FIN) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means FIN is not equal one (FIN field isn't set) and value 2 means FIN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4TcpFlagSyn 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.721
Indicates how a IPv4 TCP packet's 'Synchronize sequence numbers' field (SYN) is to be compared. The value 0 means any SYN value is allowed (don't-care field), value 1 means SYN is not equal one (FIN field isn't set) and value 2 means SYN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4TcpFlagRst 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.722
Indicates how a IPv4 TCP packet's 'Reset the connection' field (RST) is to be compared. The value 0 means any RST value is allowed (don't-care field), value 1 means RST is not equal one (FIN field isn't set) and value 2 means RST is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4TcpFlagPsh 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.723
Indicates how a IPv4 TCP packet's 'Push Function' field (PSH) is to be compared. The value 0 means any PSH value is allowed (don't-care field), value 1 means PSH is not equal one (FIN field isn't set) and value 2 means PSH is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4TcpFlagAck 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.724
Indicates how a IPv4 TCP packet's 'Acknowledgment field significant' field (ACK) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means ACK is not equal one (FIN field isn't set) and value 2 means ACK is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv4TcpFlagUrg 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.725
Indicates how a IPv4 TCP packet's 'Urgent Pointer field significant' field (URG) is to be compared. The value 0 means any URG value is allowed (don't-care field), value 1 means URG is not equal one (FIN field isn't set) and value 2 means URG is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIPv6DestMacOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.800
Indicates how a IPv6 packet's destination MAC address is to be compared. This object can only be configured if FrameType is arp(4).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200DestMacType  

me1200AclAceTableRowEditorIpv6NextHeaderOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.801
Indicates how a IPv6 packet's next header field is to be compared. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceTableRowEditorIpv6NextHeader 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.802
The next header field in the IPv6 header used to indicate a higher layer protocol. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeaderOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceTableRowEditorIpv6SrcIp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.803
The specified IPv6 source address. The packets source address is AND-ed with the value of Ipv6SrcIpMask and then compared with the value of this object. If Ipv6SrcIp and Ipv6SrcIpMask are all zeros, this entry matches any IPv6 source address. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcIpMask is not all zeros.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressIPv6  

me1200AclAceTableRowEditorIpv6SrcIpMask 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.804
The specified IPv6 source address mask. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressIPv6  

me1200AclAceTableRowEditorIpv6FlagHopLimiter 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.805
Indicates how a IPv6 packet's hop limit field is to be compared. The value 0 means any hop limit value is allowed (don't-care field), value 1 means hop limit is not equal zero and value 2 means hop limit is equal to zero. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv6Icmpv6TypeOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.806
Indicates how a IPv6 packet's ICMPv6 type field is to be compared. This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeader is icmpv6(58).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceTableRowEditorIpv6Icmpv6Type 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.807
The ICMPv6 type field in the IPv6 header. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6), Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6TypeOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceTableRowEditorIpv6Icmpv6CodeOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.808
Indicates how a IPv6 packet's ICMPv6 code field is to be compared. This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeader is icmpv6(58).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASType  

me1200AclAceTableRowEditorIpv6Icmpv6Code 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.809
The ICMPv6 code field in the IPv6 header. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6), Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6CodeOp is specific(1).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned8  

me1200AclAceTableRowEditorIpv6SrcPortOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.810
Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASRType  

me1200AclAceTableRowEditorIpv6SrcPort 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.811
The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is not any(0).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorIpv6SrcPortRange 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.812
The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is range(2).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorIpv6DestPortOp 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.813
Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200ASRType  

me1200AclAceTableRowEditorIpv6DestPort 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.814
The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6DestPortOp is not any(0).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorIpv6DestPortRange 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.815
The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6DestPortOp is range(2).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclAceTableRowEditorIpv6TcpFlagFin 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.816
Indicates how a IPv6 TCP packet's 'No more data from sender' field (FIN) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means FIN is not equal one (FIN field isn't set) and value 2 means FIN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv6TcpFlagSyn 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.817
Indicates how a IPv6 TCP packet's 'Synchronize sequence numbers' field (SYN) is to be compared. The value 0 means any SYN value is allowed (don't-care field), value 1 means SYN is not equal one (FIN field isn't set) and value 2 means SYN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv6TcpFlagRst 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.818
Indicates how a IPv6 TCP packet's 'Reset the connection' field (RST) is to be compared. The value 0 means any RST value is allowed (don't-care field), value 1 means RST is not equal one (FIN field isn't set) and value 2 means RST is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv6TcpFlagPsh 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.819
Indicates how a IPv6 TCP packet's 'Push Function' field (PSH) is to be compared. The value 0 means any PSH value is allowed (don't-care field), value 1 means PSH is not equal one (FIN field isn't set) and value 2 means PSH is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv6TcpFlagAck 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.820
Indicates how a IPv6 TCP packet's 'Acknowledgment field significant' field (ACK) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means ACK is not equal one (FIN field isn't set) and value 2 means ACK is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorIpv6TcpFlagUrg 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.821
Indicates how a IPv6 TCP packet's 'Urgent Pointer field significant' field (URG) is to be compared. The value 0 means any URG value is allowed (don't-care field), value 1 means URG is not equal one (FIN field isn't set) and value 2 means URG is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclAceFlagOpcode  

me1200AclAceTableRowEditorAction 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.1000
Action
Status: current Access: read-write
OBJECT-TYPE    
  ME1200RowEditorState  

me1200AclAcePrecedenceTable 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3
This table provides an overview of ACE by hit precedence.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ME1200AclAcePrecedenceEntry

me1200AclAcePrecedenceEntry 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1
Each row contains a set of parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  ME1200AclAcePrecedenceEntry  

me1200AclAcePrecedencePrecedenceIndex 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1.1
The ACL ACE hit precedence.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

me1200AclAcePrecedenceAceId 1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1.2
The identification for this ACE. Possible values are: 0(end of list), 1-512.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

me1200AclInterface 1.3.6.1.4.1.9.9.815.1.17.1.2.2
OBJECT IDENTIFIER    

me1200AclInterfaceTable 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1
The ACL interface configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ME1200AclInterfaceEntry

me1200AclInterfaceEntry 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1
Each interface has a set of parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  ME1200AclInterfaceEntry  

me1200AclInterfaceIfIndex 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.1
The index of logical interface, it is as well as the IF-MIB [RFC2863] objects ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  ME1200InterfaceIndex  

me1200AclInterfacePolicyId 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.2
The policy ID. Possible values are: 0-63.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

me1200AclInterfaceHitAction 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.3
The hit action.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200AclInterfaceHitAction  

me1200AclInterfaceRateLimiterId 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.4
The rate limiter ID. Possible values are: 0(disabled), 1-16.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

me1200AclInterfaceEvcPolicerId 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.5
The EVC policer ID. Possible values are: 0(disabled), 1-1022.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200Unsigned16  

me1200AclInterfaceRedirectPortList 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.6
The ingress port list for this ACE. It is active only when the hit action is denied. Set the action value to 1(deny) before the new setting. Set value 0 to disable the opertion. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  ME1200PortList  

me1200AclInterfaceMirror 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.7
The rmirror operation. Frames matching this ACE are mirrored to the destination mirror port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclInterfaceLogging 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.8
The logging operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclInterfaceShutdown 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.9
The shutdown operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclInterfaceState 1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.10
The port state of this interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclStatus 1.3.6.1.4.1.9.9.815.1.17.1.3
OBJECT IDENTIFIER    

me1200AclStatusGlobals 1.3.6.1.4.1.9.9.815.1.17.1.3.1
OBJECT IDENTIFIER    

me1200AclAceStatusTable 1.3.6.1.4.1.9.9.815.1.17.1.3.1.1
This table provides the ACE status in the hardware table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ME1200AclAceStatusEntry

me1200AclAceStatusEntry 1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1
Each row contains a set of parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  ME1200AclAceStatusEntry  

me1200AclAceStatusPrecedenceIndex 1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.2
The ACL ACE hit precedence.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

me1200AclAceStatusUser 1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.3
The application user of ACL.
Status: current Access: read-only
OBJECT-TYPE    
  ME1200AclUser  

me1200AclAceStatusAceId 1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.4
The identification for this ACE. Possible values are: 0(end of list), 1-512.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

me1200AclAceStatusConflict 1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.5
The conflict status of this ACE. When the status value is 1(true), it means the specific ACE is not applied to the hardware due to hardware limitations.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

me1200AclAceHitCountTable 1.3.6.1.4.1.9.9.815.1.17.1.3.1.2
The ACL ACE hit count table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ME1200AclAceHitCountEntry

me1200AclAceHitCountEntry 1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1
Each row has the hit count of ACE
Status: current Access: not-accessible
OBJECT-TYPE    
  ME1200AclAceHitCountEntry  

me1200AclAceHitCountAceId 1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1.1
The identification of ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

me1200AclAceHitCountHitCount 1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1.2
The hit count of this ACE.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

me1200AclStatusInterface 1.3.6.1.4.1.9.9.815.1.17.1.3.2
OBJECT IDENTIFIER    

me1200AclInterfaceHitCountTable 1.3.6.1.4.1.9.9.815.1.17.1.3.2.1
The ACL interface hit count table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ME1200AclInterfaceHitCountEntry

me1200AclInterfaceHitCountEntry 1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1
Each row has the hit count of interface
Status: current Access: not-accessible
OBJECT-TYPE    
  ME1200AclInterfaceHitCountEntry  

me1200AclInterfaceHitCountId 1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1.1
The identification of ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

me1200AclInterfaceHitCountHitCount 1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1.2
The hit count of this interface. The hit count will be increased if the incoming frame doesn't hit any ACEs.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

me1200AclControl 1.3.6.1.4.1.9.9.815.1.17.1.4
OBJECT IDENTIFIER    

me1200AclControlGlobals 1.3.6.1.4.1.9.9.815.1.17.1.4.1
OBJECT IDENTIFIER    

me1200AclControlGlobalsClearAllHitCount 1.3.6.1.4.1.9.9.815.1.17.1.4.1.1
The operation is active when the value is set to 'ture(1)'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

me1200AclMIBConformance 1.3.6.1.4.1.9.9.815.1.17.3
OBJECT IDENTIFIER    

me1200AclMIBCompliances 1.3.6.1.4.1.9.9.815.1.17.3.1
OBJECT IDENTIFIER    

me1200AclMIBGroups 1.3.6.1.4.1.9.9.815.1.17.3.2
OBJECT IDENTIFIER    

me1200AclRateLimiterTableInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.1
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclAceTableInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.2
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclAceTableRowEditorInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.3
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclAcePrecedenceTableInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.4
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclInterfaceTableInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.5
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclAceStatusTableInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.6
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclAceHitCountTableInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.7
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclInterfaceHitCountTableInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.8
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclControlGlobalsInfoGroup 1.3.6.1.4.1.9.9.815.1.17.3.2.9
A collection of objects suitable for bulk operations.
Status: current Access: read-write
OBJECT-GROUP    

me1200AclMIBCompliance 1.3.6.1.4.1.9.9.815.1.17.3.1.1
The compliance statement for the implementation.
Status: current Access: read-write
MODULE-COMPLIANCE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor