MAU-MIB

File: MAU-MIB.mib (106035 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB

Imported symbols

Counter32 Integer32 Counter64
OBJECT-TYPE MODULE-IDENTITY NOTIFICATION-TYPE
OBJECT-IDENTITY mib-2 TruthValue
AutonomousType TEXTUAL-CONVENTION OBJECT-GROUP
MODULE-COMPLIANCE NOTIFICATION-GROUP InterfaceIndex

Defined Types

JackType  
Common enumeration values for repeater and interface MAU jack types.
TEXTUAL-CONVENTION    
  INTEGER other(1), rj45(2), rj45S(3), db9(4), bnc(5), fAUI(6), mAUI(7), fiberSC(8), fiberMIC(9), fiberST(10), telco(11), mtrj(12), hssdc(13), fiberLC(14)  

RpMauEntry  
SEQUENCE    
  rpMauGroupIndex Integer32
  rpMauPortIndex Integer32
  rpMauIndex Integer32
  rpMauType AutonomousType
  rpMauStatus INTEGER
  rpMauMediaAvailable INTEGER
  rpMauMediaAvailableStateExits Counter32
  rpMauJabberState INTEGER
  rpMauJabberingStateEnters Counter32
  rpMauFalseCarriers Counter32

RpJackEntry  
SEQUENCE    
  rpJackIndex Integer32
  rpJackType JackType

IfMauEntry  
SEQUENCE    
  ifMauIfIndex InterfaceIndex
  ifMauIndex Integer32
  ifMauType AutonomousType
  ifMauStatus INTEGER
  ifMauMediaAvailable INTEGER
  ifMauMediaAvailableStateExits Counter32
  ifMauJabberState INTEGER
  ifMauJabberingStateEnters Counter32
  ifMauFalseCarriers Counter32
  ifMauTypeList Integer32
  ifMauDefaultType AutonomousType
  ifMauAutoNegSupported TruthValue
  ifMauTypeListBits BITS
  ifMauHCFalseCarriers Counter64

IfJackEntry  
SEQUENCE    
  ifJackIndex Integer32
  ifJackType JackType

IfMauAutoNegEntry  
SEQUENCE    
  ifMauAutoNegAdminStatus INTEGER
  ifMauAutoNegRemoteSignaling INTEGER
  ifMauAutoNegConfig INTEGER
  ifMauAutoNegCapability Integer32
  ifMauAutoNegCapAdvertised Integer32
  ifMauAutoNegCapReceived Integer32
  ifMauAutoNegRestart INTEGER
  ifMauAutoNegCapabilityBits BITS
  ifMauAutoNegCapAdvertisedBits BITS
  ifMauAutoNegCapReceivedBits BITS
  ifMauAutoNegRemoteFaultAdvertised INTEGER
  ifMauAutoNegRemoteFaultReceived INTEGER

BroadMauBasicEntry  
SEQUENCE    
  broadMauIfIndex InterfaceIndex
  broadMauIndex Integer32
  broadMauXmtRcvSplitType INTEGER
  broadMauXmtCarrierFreq Integer32
  broadMauTranslationFreq Integer32

Defined Values

mauMod 1.3.6.1.2.1.26.6
Management information for 802.3 MAUs. The following reference is used throughout this MIB module: [IEEE 802.3 Std] refers to: IEEE Std 802.3, 2002 Edition: 'IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications', as amended by IEEE Std 802.3ae-2002: 'Amendment: Media Access Control (MAC) Parameters, Physical Layer, and Management Parameters for 10 Gb/s Operation', August, 2002. Of particular interest is Clause 30, '10Mb/s, 100Mb/s, 1000Mb/s and 10 Gb/s Management'. Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC 3636; see the RFC itself for full legal notices.
MODULE-IDENTITY    

snmpDot3MauMgt 1.3.6.1.2.1.26
OBJECT IDENTIFIER    

dot3RpMauBasicGroup 1.3.6.1.2.1.26.1
OBJECT IDENTIFIER    

dot3IfMauBasicGroup 1.3.6.1.2.1.26.2
OBJECT IDENTIFIER    

dot3BroadMauBasicGroup 1.3.6.1.2.1.26.3
OBJECT IDENTIFIER    

dot3IfMauAutoNegGroup 1.3.6.1.2.1.26.5
OBJECT IDENTIFIER    

dot3MauType 1.3.6.1.2.1.26.4
OBJECT IDENTIFIER    

dot3MauTypeAUI 1.3.6.1.2.1.26.4.1
no internal MAU, view from AUI
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10Base5 1.3.6.1.2.1.26.4.2
thick coax MAU
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauTypeFoirl 1.3.6.1.2.1.26.4.3
FOIRL MAU
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10Base2 1.3.6.1.2.1.26.4.4
thin coax MAU
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10BaseT 1.3.6.1.2.1.26.4.5
UTP MAU. Note that it is strongly recommended that agents return either dot3MauType10BaseTHD or dot3MauType10BaseTFD if the duplex mode is known. However, management applications should be prepared to receive this MAU type value from older agent implementations.
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10BaseFP 1.3.6.1.2.1.26.4.6
passive fiber MAU
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10BaseFB 1.3.6.1.2.1.26.4.7
sync fiber MAU
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10BaseFL 1.3.6.1.2.1.26.4.8
async fiber MAU. Note that it is strongly recommended that agents return either dot3MauType10BaseFLHD or dot3MauType10BaseFLFD if the duplex mode is known. However, management applications should be prepared to receive this MAU type value from older agent implementations.
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10Broad36 1.3.6.1.2.1.26.4.9
broadband DTE MAU. Note that 10BROAD36 MAUs can be attached to interfaces but not to repeaters.
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10BaseTHD 1.3.6.1.2.1.26.4.10
UTP MAU, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10BaseTFD 1.3.6.1.2.1.26.4.11
UTP MAU, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10BaseFLHD 1.3.6.1.2.1.26.4.12
async fiber MAU, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10BaseFLFD 1.3.6.1.2.1.26.4.13
async fiber MAU, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType100BaseT4 1.3.6.1.2.1.26.4.14
4 pair category 3 UTP
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType100BaseTXHD 1.3.6.1.2.1.26.4.15
2 pair category 5 UTP, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType100BaseTXFD 1.3.6.1.2.1.26.4.16
2 pair category 5 UTP, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType100BaseFXHD 1.3.6.1.2.1.26.4.17
X fiber over PMT, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType100BaseFXFD 1.3.6.1.2.1.26.4.18
X fiber over PMT, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType100BaseT2HD 1.3.6.1.2.1.26.4.19
2 pair category 3 UTP, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType100BaseT2FD 1.3.6.1.2.1.26.4.20
2 pair category 3 UTP, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseXHD 1.3.6.1.2.1.26.4.21
PCS/PMA, unknown PMD, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseXFD 1.3.6.1.2.1.26.4.22
PCS/PMA, unknown PMD, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseLXHD 1.3.6.1.2.1.26.4.23
Fiber over long-wavelength laser, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseLXFD 1.3.6.1.2.1.26.4.24
Fiber over long-wavelength laser, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseSXHD 1.3.6.1.2.1.26.4.25
Fiber over short-wavelength laser, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseSXFD 1.3.6.1.2.1.26.4.26
Fiber over short-wavelength laser, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseCXHD 1.3.6.1.2.1.26.4.27
Copper over 150-Ohm balanced cable, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseCXFD 1.3.6.1.2.1.26.4.28
Copper over 150-Ohm balanced cable, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseTHD 1.3.6.1.2.1.26.4.29
Four-pair Category 5 UTP, half duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType1000BaseTFD 1.3.6.1.2.1.26.4.30
Four-pair Category 5 UTP, full duplex mode
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseX 1.3.6.1.2.1.26.4.31
X PCS/PMA, unknown PMD.
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseLX4 1.3.6.1.2.1.26.4.32
X fiber over WWDM optics
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseR 1.3.6.1.2.1.26.4.33
R PCS/PMA, unknown PMD.
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseER 1.3.6.1.2.1.26.4.34
R fiber over 1550 nm optics
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseLR 1.3.6.1.2.1.26.4.35
R fiber over 1310 nm optics
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseSR 1.3.6.1.2.1.26.4.36
R fiber over 850 nm optics
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseW 1.3.6.1.2.1.26.4.37
W PCS/PMA, unknown PMD.
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseEW 1.3.6.1.2.1.26.4.38
W fiber over 1550 nm optics
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseLW 1.3.6.1.2.1.26.4.39
W fiber over 1310 nm optics
Status: current Access: read-write
OBJECT-IDENTITY    

dot3MauType10GigBaseSW 1.3.6.1.2.1.26.4.40
W fiber over 850 nm optics
Status: current Access: read-write
OBJECT-IDENTITY    

rpMauTable 1.3.6.1.2.1.26.1.1
Table of descriptive and status information about the MAU(s) attached to the ports of a repeater.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RpMauEntry

rpMauEntry 1.3.6.1.2.1.26.1.1.1
An entry in the table, containing information about a single MAU.
Status: current Access: not-accessible
OBJECT-TYPE    
  RpMauEntry  

rpMauGroupIndex 1.3.6.1.2.1.26.1.1.1.1
This variable uniquely identifies the group containing the port to which the MAU described by this entry is connected. Note: In practice, a group will generally be a field-replaceable unit (i.e., module, card, or board) that can fit in the physical system enclosure, and the group number will correspond to a number marked on the physical enclosure. The group denoted by a particular value of this object is the same as the group denoted by the same value of rptrGroupIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

rpMauPortIndex 1.3.6.1.2.1.26.1.1.1.2
This variable uniquely identifies the repeater port within group rpMauGroupIndex to which the MAU described by this entry is connected.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

rpMauIndex 1.3.6.1.2.1.26.1.1.1.3
This variable uniquely identifies the MAU described by this entry from among other MAUs connected to the same port (rpMauPortIndex).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

rpMauType 1.3.6.1.2.1.26.1.1.1.4
This object identifies the MAU type. Values for standard IEEE 802.3 MAU types are defined above. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

rpMauStatus 1.3.6.1.2.1.26.1.1.1.5
The current state of the MAU. This object MAY be implemented as a read-only object by those agents and MAUs that do not implement software control of the MAU state. Some agents may not support setting the value of this object to some of the enumerated values. The value other(1) is returned if the MAU is in a state other than one of the states 2 through 6. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. A MAU in the operational(3) state is fully functional, operates, and passes signals to its attached DTE or repeater port in accordance to its specification. A MAU in standby(4) state forces DI and CI to idle and the media transmitter to idle or fault, if supported. Standby(4) mode only applies to link type MAUs. The state of rpMauMediaAvailable is unaffected. A MAU in shutdown(5) state assumes the same condition on DI, CI, and the media transmitter as though it were powered down or not connected. The MAU MAY return other(1) value for the rpMauJabberState and rpMauMediaAvailable objects when it is in this state. For an AUI, this state will remove power from the AUI. Setting this variable to the value reset(6) resets the MAU in the same manner as a power-off, power-on cycle of at least one-half second would. The agent is not required to return the value reset (6). Setting this variable to the value operational(3), standby(4), or shutdown(5) causes the MAU to assume the respective state except that setting a mixing-type MAU or an AUI to standby(4) will cause the MAU to enter the shutdown state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), unknown(2), operational(3), standby(4), shutdown(5), reset(6)  

rpMauMediaAvailable 1.3.6.1.2.1.26.1.1.1.6
If the MAU is a link or fiber type (FOIRL, 10BASE-T, 10BASE-F) then this is equivalent to the link test fail state/low light function. For an AUI or a coax (including broadband) MAU this indicates whether or not loopback is detected on the DI circuit. The value of this attribute persists between packets for MAU types AUI, 10BASE5, 10BASE2, 10BROAD36, and 10BASE-FP. The value other(1) is returned if the mediaAvailable state is not one of 2 through 11. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. At power-up or following a reset, the value of this attribute will be unknown for AUI, coax, and 10BASE-FP MAUs. For these MAUs loopback will be tested on each transmission during which no collision is detected. If DI is receiving input when DO returns to IDL after a transmission and there has been no collision during the transmission then loopback will be detected. The value of this attribute will only change during non-collided transmissions for AUI, coax, and 10BASE-FP MAUs. For 100Mbps and 1000Mbps MAUs, the enumerations match the states within the respective link integrity state diagrams, fig 32-16, 23-12 and 24-15 of sections 32, 23 and 24 of [IEEE802.3]. Any MAU which implements management of auto-negotiation will map remote fault indication to remote fault. The value available(3) indicates that the link, light, or loopback is normal. The value notAvailable(4) indicates link loss, low light, or no loopback. The value remoteFault(5) indicates that a fault has been detected at the remote end of the link. This value applies to 10BASE-FB, 100BASE-T4 Far End Fault Indication and non-specified remote faults from a system running auto-negotiation. The values remoteJabber(7), remoteLinkLoss(8), and remoteTest(9) SHOULD be used instead of remoteFault(5) where the reason for remote fault is identified in the remote signaling protocol. The value invalidSignal(6) indicates that an invalid signal has been received from the other end of the link. invalidSignal(6) applies only to MAUs of type 10BASE-FB. Where an IEEE Std 802.3-2002 clause 22 MII is present, a logic one in the remote fault bit (reference section 22.2.4.2.8 of that document) maps to the value remoteFault(5), and a logic zero in the link status bit (reference section 22.2.4.2.10 of that document) maps to the value notAvailable(4). The value notAvailable(4) takes precedence over the value remoteFault(5). Any MAU that implements management of clause 37 Auto-Negotiation will map the received Remote Fault (RF1 and RF2) bit values for Offline to offline(10), Link Failure to remoteFault(5) and Auto-Negotiation Error to autoNegError(11).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), unknown(2), available(3), notAvailable(4), remoteFault(5), invalidSignal(6), remoteJabber(7), remoteLinkLoss(8), remoteTest(9), offline(10), autoNegError(11)  

rpMauMediaAvailableStateExits 1.3.6.1.2.1.26.1.1.1.7
A count of the number of times that rpMauMediaAvailable for this MAU instance leaves the state available(3). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rptrMonitorPortLastChange.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rpMauJabberState 1.3.6.1.2.1.26.1.1.1.8
The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. If the MAU is not jabbering the agent returns noJabber(3). This is the 'normal' state. If the MAU is in jabber state the agent returns the jabbering(4) value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), unknown(2), noJabber(3), jabbering(4)  

rpMauJabberingStateEnters 1.3.6.1.2.1.26.1.1.1.9
A count of the number of times that mauJabberState for this MAU instance enters the state jabbering(4). For MAUs of type dot3MauTypeAUI, dot3MauType100BaseT4, dot3MauType100BaseTX, dot3MauType100BaseFX and all 1000Mbps types, this counter will always indicate zero. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rptrMonitorPortLastChange.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rpMauFalseCarriers 1.3.6.1.2.1.26.1.1.1.10
A count of the number of false carrier events during IDLE in 100BASE-X links. This counter does not increment at the symbol rate. It can increment after a valid carrier completion at a maximum rate of once per 100 ms until the next carrier event. This counter increments only for MAUs of type dot3MauType100BaseT4, dot3MauType100BaseTX, and dot3MauType100BaseFX and all 1000Mbps types. For all other MAU types, this counter will always indicate zero. The approximate minimum time for rollover of this counter is 7.4 hours. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rptrMonitorPortLastChange.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rpJackTable 1.3.6.1.2.1.26.1.2
Information about the external jacks attached to MAUs attached to the ports of a repeater.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RpJackEntry

rpJackEntry 1.3.6.1.2.1.26.1.2.1
An entry in the table, containing information about a particular jack.
Status: current Access: not-accessible
OBJECT-TYPE    
  RpJackEntry  

rpJackIndex 1.3.6.1.2.1.26.1.2.1.1
This variable uniquely identifies the jack described by this entry from among other jacks attached to the same MAU (rpMauIndex).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

rpJackType 1.3.6.1.2.1.26.1.2.1.2
The jack connector type, as it appears on the outside of the system.
Status: current Access: read-only
OBJECT-TYPE    
  JackType  

ifMauTable 1.3.6.1.2.1.26.2.1
Table of descriptive and status information about MAU(s) attached to an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IfMauEntry

ifMauEntry 1.3.6.1.2.1.26.2.1.1
An entry in the table, containing information about a single MAU.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfMauEntry  

ifMauIfIndex 1.3.6.1.2.1.26.2.1.1.1
This variable uniquely identifies the interface to which the MAU described by this entry is connected.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

ifMauIndex 1.3.6.1.2.1.26.2.1.1.2
This variable uniquely identifies the MAU described by this entry from among other MAUs connected to the same interface (ifMauIfIndex).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

ifMauType 1.3.6.1.2.1.26.2.1.1.3
This object identifies the MAU type. Values for standard IEEE 802.3 MAU types are defined above. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object ifMauDefaultType. In case (2), a set to the object ifMauDefaultType will force the MAU into the new operating mode.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

ifMauStatus 1.3.6.1.2.1.26.2.1.1.4
The current state of the MAU. This object MAY be implemented as a read-only object by those agents and MAUs that do not implement software control of the MAU state. Some agents may not support setting the value of this object to some of the enumerated values. The value other(1) is returned if the MAU is in a state other than one of the states 2 through 6. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. A MAU in the operational(3) state is fully functional, operates, and passes signals to its attached DTE or repeater port in accordance to its specification. A MAU in standby(4) state forces DI and CI to idle and the media transmitter to idle or fault, if supported. Standby(4) mode only applies to link type MAUs. The state of ifMauMediaAvailable is unaffected. A MAU in shutdown(5) state assumes the same condition on DI, CI, and the media transmitter as though it were powered down or not connected. The MAU MAY return other(1) value for the ifMauJabberState and ifMauMediaAvailable objects when it is in this state. For an AUI, this state will remove power from the AUI. Setting this variable to the value reset(6) resets the MAU in the same manner as a power-off, power-on cycle of at least one-half second would. The agent is not required to return the value reset (6). Setting this variable to the value operational(3), standby(4), or shutdown(5) causes the MAU to assume the respective state except that setting a mixing-type MAU or an AUI to standby(4) will cause the MAU to enter the shutdown state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), unknown(2), operational(3), standby(4), shutdown(5), reset(6)  

ifMauMediaAvailable 1.3.6.1.2.1.26.2.1.1.5
If the MAU is a link or fiber type (FOIRL, 10BASE-T, 10BASE-F) then this is equivalent to the link test fail state/low light function. For an AUI or a coax (including broadband) MAU this indicates whether or not loopback is detected on the DI circuit. The value of this attribute persists between packets for MAU types AUI, 10BASE5, 10BASE2, 10BROAD36, and 10BASE-FP. The value other(1) is returned if the mediaAvailable state is not one of 2 through 18. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. At power-up or following a reset, the value of this attribute will be unknown for AUI, coax, and 10BASE-FP MAUs. For these MAUs loopback will be tested on each transmission during which no collision is detected. If DI is receiving input when DO returns to IDL after a transmission and there has been no collision during the transmission then loopback will be detected. The value of this attribute will only change during non-collided transmissions for AUI, coax, and 10BASE-FP MAUs. For 100Mbps and 1000Mbps MAUs, the enumerations match the states within the respective link integrity state diagrams, fig 32-16, 23-12 and 24-15 of sections 32, 23 and 24 of [IEEE802.3]. Any MAU which implements management of auto-negotiation will map remote fault indication to remote fault. The value available(3) indicates that the link, light, or loopback is normal. The value notAvailable(4) indicates link loss, low light, or no loopback. The value remoteFault(5) indicates that a fault has been detected at the remote end of the link. This value applies to 10BASE-FB, 100BASE-T4 Far End Fault Indication and non-specified remote faults from a system running auto-negotiation. The values remoteJabber(7), remoteLinkLoss(8), and remoteTest(9) SHOULD be used instead of remoteFault(5) where the reason for remote fault is identified in the remote signaling protocol. The value invalidSignal(6) indicates that an invalid signal has been received from the other end of the link. invalidSignal(6) applies only to MAUs of type 10BASE-FB. Where an IEEE Std 802.3-2002 clause 22 MII is present, a logic one in the remote fault bit (reference section 22.2.4.2.8 of that document) maps to the value remoteFault(5), and a logic zero in the link status bit (reference section 22.2.4.2.10 of that document) maps to the value notAvailable(4). The value notAvailable(4) takes precedence over the value remoteFault(5). Any MAU that implements management of clause 37 Auto-Negotiation will map the received RF1 and RF2 bit values for Offline to offline(10), Link Failure to remoteFault(5) and Auto-Negotiation Error to autoNegError(11). For 10 Gb/s, the enumerations map to the states within the Reconciliation Sublayer state diagram as follows: NoFault maps to the enumeration 'available(3)' LocalFault maps to the enumeration 'notAvailable(4)' RemoteFault maps to the enumeration 'remoteFault(5)' The enumerations 'pmdLinkFault(12)', 'wisFrameLoss(13)', 'wisSignalLoss(14)', 'pcsLinkFault(15)', 'excessiveBER(16)', and 'dxsLinkFault(17)' and 'pxsLinkFault(18)' should be used instead of the enumeration 'notAvailable(4)' where the reason for the local fault can be identified through the use of the MDIO Interface. Where multiple reasons for the local fault state can be identified only the highest precedence error should be reported. The precedence in descending order is as follows: pxsLinkFault pmdLinkFault wisFrameLoss wisSignalLoss pcsLinkFault excessiveBER dxsLinkFault
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), unknown(2), available(3), notAvailable(4), remoteFault(5), invalidSignal(6), remoteJabber(7), remoteLinkLoss(8), remoteTest(9), offline(10), autoNegError(11), pmdLinkFault(12), wisFrameLoss(13), wisSignalLoss(14), pcsLinkFault(15), excessiveBER(16), dxsLinkFault(17), pxsLinkFault(18)  

ifMauMediaAvailableStateExits 1.3.6.1.2.1.26.2.1.1.6
A count of the number of times that ifMauMediaAvailable for this MAU instance leaves the state available(3). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ifMauJabberState 1.3.6.1.2.1.26.2.1.1.7
The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. If the MAU is not jabbering the agent returns noJabber(3). This is the 'normal' state. If the MAU is in jabber state the agent returns the jabbering(4) value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), unknown(2), noJabber(3), jabbering(4)  

ifMauJabberingStateEnters 1.3.6.1.2.1.26.2.1.1.8
A count of the number of times that mauJabberState for this MAU instance enters the state jabbering(4). This counter will always indicate zero for MAUs of type dot3MauTypeAUI and those of speeds above 10Mbps. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ifMauFalseCarriers 1.3.6.1.2.1.26.2.1.1.9
A count of the number of false carrier events during IDLE in 100BASE-X and 1000BASE-X links. For all other MAU types, this counter will always indicate zero. This counter does not increment at the symbol rate. It can increment after a valid carrier completion at a maximum rate of once per 100 ms for 100BASE-X and once per 10us for 1000BASE-X until the next CarrierEvent. This counter can roll over very quickly. A management station is advised to poll the ifMauHCFalseCarriers instead of this counter in order to avoid loss of information. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ifMauTypeList 1.3.6.1.2.1.26.2.1.1.10
********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauTypeListBits. A value that uniquely identifies the set of possible IEEE 802.3 types that the MAU could be. The value is a sum which initially takes the value zero. Then, for each type capability of this MAU, 2 raised to the power noted below is added to the sum. For example, a MAU which has the capability to be only 10BASE-T would have a value of 512 (2**9). In contrast, a MAU which supports both 10Base-T (full duplex) and 100BASE-TX (full duplex) would have a value of ((2**11) + (2**16)) or 67584. The powers of 2 assigned to the capabilities are these: Power Capability 0 other or unknown 1 AUI 2 10BASE-5 3 FOIRL 4 10BASE-2 5 10BASE-T duplex mode unknown 6 10BASE-FP 7 10BASE-FB 8 10BASE-FL duplex mode unknown 9 10BROAD36 10 10BASE-T half duplex mode 11 10BASE-T full duplex mode 12 10BASE-FL half duplex mode 13 10BASE-FL full duplex mode 14 100BASE-T4 15 100BASE-TX half duplex mode 16 100BASE-TX full duplex mode 17 100BASE-FX half duplex mode 18 100BASE-FX full duplex mode 19 100BASE-T2 half duplex mode 20 100BASE-T2 full duplex mode If auto-negotiation is present on this MAU, this object will map to ifMauAutoNegCapability.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ifMauDefaultType 1.3.6.1.2.1.26.2.1.1.11
This object identifies the default administrative baseband MAU type, to be used in conjunction with the operational MAU type denoted by ifMauType. The set of possible values for this object is the same as the set defined for the ifMauType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. NOTE TO IMPLEMENTORS: It may be necessary to provide for underlying hardware implementations which do not follow the exact behavior specified above. In particular, when ifMauAutoNegAdminStatus transitions from enabled to disabled, the agent implementation MUST ensure that the operational type of the MAU (as reported by ifMauType) correctly transitions to the value specified by this object, rather than continuing to operate at the value earlier determined by the auto-negotiation function.
Status: current Access: read-write
OBJECT-TYPE    
  AutonomousType  

ifMauAutoNegSupported 1.3.6.1.2.1.26.2.1.1.12
This object indicates whether or not auto-negotiation is supported on this MAU.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ifMauTypeListBits 1.3.6.1.2.1.26.2.1.1.13
A value that uniquely identifies the set of possible IEEE 802.3 types that the MAU could be. If auto-negotiation is present on this MAU, this object will map to ifMauAutoNegCapabilityBits. Note that this MAU may be capable of operating as a MAU type that is beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for capabilities that are listed above.
Status: current Access: read-only
OBJECT-TYPE    
  BITS bOther(0), bAUI(1), b10base5(2), bFoirl(3), b10base2(4), b10baseT(5), b10baseFP(6), b10baseFB(7), b10baseFL(8), b10broad36(9), b10baseTHD(10), b10baseTFD(11), b10baseFLHD(12), b10baseFLFD(13), b100baseT4(14), b100baseTXHD(15), b100baseTXFD(16), b100baseFXHD(17), b100baseFXFD(18), b100baseT2HD(19), b100baseT2FD(20), b1000baseXHD(21), b1000baseXFD(22), b1000baseLXHD(23), b1000baseLXFD(24), b1000baseSXHD(25), b1000baseSXFD(26), b1000baseCXHD(27), b1000baseCXFD(28), b1000baseTHD(29), b1000baseTFD(30), b10GbaseX(31), b10GbaseLX4(32), b10GbaseR(33), b10GbaseER(34), b10GbaseLR(35), b10GbaseSR(36), b10GbaseW(37), b10GbaseEW(38), b10GbaseLW(39), b10GbaseSW(40)  

ifMauHCFalseCarriers 1.3.6.1.2.1.26.2.1.1.14
A count of the number of false carrier events during IDLE in 100BASE-X and 1000BASE-X links. For all other MAU types, this counter will always indicate zero. This counter does not increment at the symbol rate. This counter is a 64 bit version of ifMauFalseCarriers. Since the 32 bit version of this counter can roll over very quickly, management stations are advised to poll the 64 bit version instead in order to avoid loss of information. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

ifJackTable 1.3.6.1.2.1.26.2.2
Information about the external jacks attached to MAUs attached to an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IfJackEntry

ifJackEntry 1.3.6.1.2.1.26.2.2.1
An entry in the table, containing information about a particular jack.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfJackEntry  

ifJackIndex 1.3.6.1.2.1.26.2.2.1.1
This variable uniquely identifies the jack described by this entry from among other jacks attached to the same MAU.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

ifJackType 1.3.6.1.2.1.26.2.2.1.2
The jack connector type, as it appears on the outside of the system.
Status: current Access: read-only
OBJECT-TYPE    
  JackType  

ifMauAutoNegTable 1.3.6.1.2.1.26.5.1
Configuration and status objects for the auto-negotiation function of MAUs attached to interfaces. The ifMauAutoNegTable applies to systems in which auto-negotiation is supported on one or more MAUs attached to interfaces. Note that if auto-negotiation is present and enabled, the ifMauType object reflects the result of the auto-negotiation function.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IfMauAutoNegEntry

ifMauAutoNegEntry 1.3.6.1.2.1.26.5.1.1
An entry in the table, containing configuration and status information for the auto-negotiation function of a particular MAU.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfMauAutoNegEntry  

ifMauAutoNegAdminStatus 1.3.6.1.2.1.26.5.1.1.1
Setting this object to enabled(1) will cause the interface which has the auto-negotiation signaling ability to be enabled. If the value of this object is disabled(2) then the interface will act as it would if it had no auto-negotiation signaling. Under these conditions, an IEEE 802.3 MAU will immediately be forced to the state indicated by the value of the object ifMauDefaultType. NOTE TO IMPLEMENTORS: When ifMauAutoNegAdminStatus transitions from enabled to disabled, the agent implementation MUST ensure that the operational type of the MAU (as reported by ifMauType) correctly transitions to the value specified by the ifMauDefaultType object, rather than continuing to operate at the value earlier determined by the auto-negotiation function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ifMauAutoNegRemoteSignaling 1.3.6.1.2.1.26.5.1.1.2
A value indicating whether the remote end of the link is using auto-negotiation signaling. It takes the value detected(1) if and only if, during the previous link negotiation, FLP Bursts were received.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER detected(1), notdetected(2)  

ifMauAutoNegConfig 1.3.6.1.2.1.26.5.1.1.4
A value indicating the current status of the auto-negotiation process. The enumeration parallelDetectFail(5) maps to a failure in parallel detection as defined in 28.2.3.1 of [IEEE 802.3 Std].
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), configuring(2), complete(3), disabled(4), parallelDetectFail(5)  

ifMauAutoNegCapability 1.3.6.1.2.1.26.5.1.1.5
********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapabilityBits. A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. The value is a sum which initially takes the value zero. Then, for each capability of this interface, 2 raised to the power noted below is added to the sum. For example, an interface which has the capability to support only 100Base-TX half duplex would have a value of 32768 (2**15). In contrast, an interface which supports both 100Base-TX half duplex and and 100Base-TX full duplex would have a value of 98304 ((2**15) + (2**16)). The powers of 2 assigned to the capabilities are these: Power Capability 0 other or unknown (1-9) (reserved) 10 10BASE-T half duplex mode 11 10BASE-T full duplex mode 12 (reserved) 13 (reserved) 14 100BASE-T4 15 100BASE-TX half duplex mode 16 100BASE-TX full duplex mode 17 (reserved) 18 (reserved) 19 100BASE-T2 half duplex mode 20 100BASE-T2 full duplex mode Note that interfaces that support this MIB may have capabilities that extend beyond the scope of this MIB.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ifMauAutoNegCapAdvertised 1.3.6.1.2.1.26.5.1.1.6
********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapAdvertisedBits. A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Refer to ifMauAutoNegCapability for a description of the possible values of this object. Capabilities in this object that are not available in ifMauAutoNegCapability cannot be enabled.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

ifMauAutoNegCapReceived 1.3.6.1.2.1.26.5.1.1.7
********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapReceivedBits. A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Refer to ifMauAutoNegCapability for a description of the possible values of this object. Note that interfaces that support this MIB may be attached to remote auto-negotiation entities which have capabilities beyond the scope of this MIB.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ifMauAutoNegRestart 1.3.6.1.2.1.26.5.1.1.8
If the value of this object is set to restart(1) then this will force auto-negotiation to begin link renegotiation. If auto-negotiation signaling is disabled, a write to this object has no effect. Setting the value of this object to norestart(2) has no effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER restart(1), norestart(2)  

ifMauAutoNegCapabilityBits 1.3.6.1.2.1.26.5.1.1.9
A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. Note that interfaces that support this MIB may have capabilities that extend beyond the scope of this MIB. Note that the local auto-negotiation entity may support some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for capabilities that are listed above.
Status: current Access: read-only
OBJECT-TYPE    
  BITS bOther(0), b10baseT(1), b10baseTFD(2), b100baseT4(3), b100baseTX(4), b100baseTXFD(5), b100baseT2(6), b100baseT2FD(7), bfdxPause(8), bfdxAPause(9), bfdxSPause(10), bfdxBPause(11), b1000baseX(12), b1000baseXFD(13), b1000baseT(14), b1000baseTFD(15)  

ifMauAutoNegCapAdvertisedBits 1.3.6.1.2.1.26.5.1.1.10
A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in ifMauAutoNegCapabilityBits cannot be enabled. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for capabilities that are listed above.
Status: current Access: read-write
OBJECT-TYPE    
  BITS bOther(0), b10baseT(1), b10baseTFD(2), b100baseT4(3), b100baseTX(4), b100baseTXFD(5), b100baseT2(6), b100baseT2FD(7), bFdxPause(8), bFdxAPause(9), bFdxSPause(10), bFdxBPause(11), b1000baseX(12), b1000baseXFD(13), b1000baseT(14), b1000baseTFD(15)  

ifMauAutoNegCapReceivedBits 1.3.6.1.2.1.26.5.1.1.11
A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Note that interfaces that support this MIB may be attached to remote auto-negotiation entities which have capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for capabilities that are listed above.
Status: current Access: read-only
OBJECT-TYPE    
  BITS bOther(0), b10baseT(1), b10baseTFD(2), b100baseT4(3), b100baseTX(4), b100baseTXFD(5), b100baseT2(6), b100baseT2FD(7), bFdxPause(8), bFdxAPause(9), bFdxSPause(10), bFdxBPause(11), b1000baseX(12), b1000baseXFD(13), b1000baseT(14), b1000baseTFD(15)  

ifMauAutoNegRemoteFaultAdvertised 1.3.6.1.2.1.26.5.1.1.12
A value that identifies any local fault indications that this MAU has detected and will advertise at the next auto-negotiation interaction for 1000Mbps MAUs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noError(1), offline(2), linkFailure(3), autoNegError(4)  

ifMauAutoNegRemoteFaultReceived 1.3.6.1.2.1.26.5.1.1.13
A value that identifies any fault indications received from the far end of a link by the local auto-negotiation entity for 1000Mbps MAUs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(1), offline(2), linkFailure(3), autoNegError(4)  

broadMauBasicTable 1.3.6.1.2.1.26.3.1
********* THIS OBJECT IS DEPRECATED ********** This entire table has been deprecated. There have been no reported implementations of this table, and it is unlikely that there ever will be. IEEE recommends that broadband MAU types should not be used for new installations. Table of descriptive and status information about the broadband MAUs connected to interfaces.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BroadMauBasicEntry

broadMauBasicEntry 1.3.6.1.2.1.26.3.1.1
********* THIS OBJECT IS DEPRECATED ********** An entry in the table, containing information about a single broadband MAU.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  BroadMauBasicEntry  

broadMauIfIndex 1.3.6.1.2.1.26.3.1.1.1
********* THIS OBJECT IS DEPRECATED ********** This variable uniquely identifies the interface to which the MAU described by this entry is connected.
Status: deprecated Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

broadMauIndex 1.3.6.1.2.1.26.3.1.1.2
********* THIS OBJECT IS DEPRECATED ********** This variable uniquely identifies the MAU connected to interface broadMauIfIndex that is described by this entry.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

broadMauXmtRcvSplitType 1.3.6.1.2.1.26.3.1.1.3
********* THIS OBJECT IS DEPRECATED ********** This object indicates the type of frequency multiplexing/cabling system used to separate the transmit and receive paths for the 10BROAD36 MAU. The value other(1) is returned if the split type is not either single or dual. The value single(2) indicates a single cable system. The value dual(3) indicates a dual cable system, offset normally zero.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER other(1), single(2), dual(3)  

broadMauXmtCarrierFreq 1.3.6.1.2.1.26.3.1.1.4
********* THIS OBJECT IS DEPRECATED ********** This variable indicates the transmit carrier frequency of the 10BROAD36 MAU in MHz/4; that is, in units of 250 kHz.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

broadMauTranslationFreq 1.3.6.1.2.1.26.3.1.1.5
********* THIS OBJECT IS DEPRECATED ********** This variable indicates the translation offset frequency of the 10BROAD36 MAU in MHz/4; that is, in units of 250 kHz.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

snmpDot3MauTraps 1.3.6.1.2.1.26.0
OBJECT IDENTIFIER    

rpMauJabberTrap 1.3.6.1.2.1.26.0.1
This trap is sent whenever a managed repeater MAU enters the jabber state. The agent MUST throttle the generation of consecutive rpMauJabberTraps so that there is at least a five-second gap between them.
Status: current Access: read-only
NOTIFICATION-TYPE    

ifMauJabberTrap 1.3.6.1.2.1.26.0.2
This trap is sent whenever a managed interface MAU enters the jabber state. The agent MUST throttle the generation of consecutive ifMauJabberTraps so that there is at least a five-second gap between them.
Status: current Access: read-only
NOTIFICATION-TYPE    

mauModConf 1.3.6.1.2.1.26.6.1
OBJECT IDENTIFIER    

mauModCompls 1.3.6.1.2.1.26.6.1.1
OBJECT IDENTIFIER    

mauModObjGrps 1.3.6.1.2.1.26.6.1.2
OBJECT IDENTIFIER    

mauModNotGrps 1.3.6.1.2.1.26.6.1.3
OBJECT IDENTIFIER    

mauRpGrpBasic 1.3.6.1.2.1.26.6.1.2.1
Basic conformance group for MAUs attached to repeater ports. This group is also the conformance specification for RFC 1515 implementations.
Status: current Access: read-only
OBJECT-GROUP    

mauRpGrp100Mbs 1.3.6.1.2.1.26.6.1.2.2
Conformance group for MAUs attached to repeater ports with 100 Mb/s or greater capability.
Status: current Access: read-only
OBJECT-GROUP    

mauRpGrpJack 1.3.6.1.2.1.26.6.1.2.3
Conformance group for MAUs attached to repeater ports with managed jacks.
Status: current Access: read-only
OBJECT-GROUP    

mauIfGrpBasic 1.3.6.1.2.1.26.6.1.2.4
Basic conformance group for MAUs attached to interfaces. This group also provides a conformance specification for RFC 1515 implementations.
Status: current Access: read-only
OBJECT-GROUP    

mauIfGrp100Mbs 1.3.6.1.2.1.26.6.1.2.5
********* THIS GROUP IS DEPRECATED ********** Conformance group for MAUs attached to interfaces with 100 Mb/s capability. This object group has been deprecated in favor of mauIfGrpHighCapacity.
Status: deprecated Access: read-only
OBJECT-GROUP    

mauIfGrpJack 1.3.6.1.2.1.26.6.1.2.6
Conformance group for MAUs attached to interfaces with managed jacks.
Status: current Access: read-only
OBJECT-GROUP    

mauIfGrpAutoNeg 1.3.6.1.2.1.26.6.1.2.7
********* THIS GROUP IS DEPRECATED ********** Conformance group for MAUs attached to interfaces with managed auto-negotiation. This object group has been deprecated in favor of mauIfGrpAutoNeg2.
Status: deprecated Access: read-only
OBJECT-GROUP    

mauBroadBasic 1.3.6.1.2.1.26.6.1.2.8
********* THIS GROUP IS DEPRECATED ********** Conformance group for broadband MAUs attached to interfaces. This object group is deprecated. There have been no reported implementations of this group, and it was felt to be unlikely that there will be any future implementations.
Status: deprecated Access: read-only
OBJECT-GROUP    

mauIfGrpHighCapacity 1.3.6.1.2.1.26.6.1.2.9
Conformance group for MAUs attached to interfaces with 100 Mb/s or greater capability.
Status: current Access: read-only
OBJECT-GROUP    

mauIfGrpAutoNeg2 1.3.6.1.2.1.26.6.1.2.10
Conformance group for MAUs attached to interfaces with managed auto-negotiation.
Status: current Access: read-only
OBJECT-GROUP    

mauIfGrpAutoNeg1000Mbps 1.3.6.1.2.1.26.6.1.2.11
Conformance group for 1000Mbps MAUs attached to interfaces with managed auto-negotiation.
Status: current Access: read-only
OBJECT-GROUP    

mauIfGrpHCStats 1.3.6.1.2.1.26.6.1.2.12
Conformance for high capacity statistics for MAUs attached to interfaces
Status: current Access: read-only
OBJECT-GROUP    

rpMauNotifications 1.3.6.1.2.1.26.6.1.3.1
Notifications for repeater MAUs.
Status: current Access: read-only
NOTIFICATION-GROUP    

ifMauNotifications 1.3.6.1.2.1.26.6.1.3.2
Notifications for interface MAUs.
Status: current Access: read-only
NOTIFICATION-GROUP    

mauModRpCompl 1.3.6.1.2.1.26.6.1.1.1
******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to repeater ports. This compliance is deprecated and replaced by mauModRpCompl2, which corrects an oversight by allowing rpMauStatus to be implemented read-only.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

mauModIfCompl 1.3.6.1.2.1.26.6.1.1.2
******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to interfaces. This compliance is deprecated and replaced by mauModIfCompl2.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

mauModIfCompl2 1.3.6.1.2.1.26.6.1.1.3
******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to interfaces. This compliance is deprecated and replaced by mauModIfCompl3.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

mauModRpCompl2 1.3.6.1.2.1.26.6.1.1.4
Compliance for MAUs attached to repeater ports. Note that compliance with this compliance statement requires compliance with the snmpRptrModCompl MODULE-COMPLIANCE statement of the SNMP-REPEATER-MIB (RFC 2108).
Status: current Access: read-only
MODULE-COMPLIANCE    

mauModIfCompl3 1.3.6.1.2.1.26.6.1.1.5
Compliance for MAUs attached to interfaces. Note that compliance with this compliance statement requires compliance with the ifCompliance3 MODULE-COMPLIANCE statement of the IF-MIB (RFC 2863) and the dot3Compliance2 MODULE-COMPLIANCE statement of the EtherLike-MIB (RFC3635).
Status: current Access: read-only
MODULE-COMPLIANCE