LOOPBACK-DETECT-MIB
File:
LOOPBACK-DETECT-MIB.mib (9557 bytes)
Imported modules
Imported symbols
Defined Types
SwLoopDetectPortEntry |
|
SEQUENCE |
|
|
|
|
swLoopDetectPortIndex |
INTEGER |
|
|
swLoopDetectPortState |
INTEGER |
|
|
swLoopDetectPortLoopVLAN |
DisplayString |
|
|
swLoopDetectPortLoopStatus |
INTEGER |
|
Defined Values
swLoopDetectMIB |
1.3.6.1.4.1.171.12.41 |
The structure of loopback detection management for the
proprietary enterprise. |
MODULE-IDENTITY |
|
|
|
swLoopDetectAdminState |
1.3.6.1.4.1.171.12.41.1.1 |
This object indicates the loopback detection status for the system. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enabled(1), disabled(2) |
|
swLoopDetectInterval |
1.3.6.1.4.1.171.12.41.1.2 |
This object indicates the interval value. The range is from 1 to 32767 seconds. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..32767 |
|
swLoopDetectRecoverTime |
1.3.6.1.4.1.171.12.41.1.3 |
This object indicates the recover time. The range is from 60 to 1000000.
The value of 0 disables the recover function. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1000000 |
|
swLoopDetectMode |
1.3.6.1.4.1.171.12.41.1.4 |
This object indicates the loopback detection mode for the system. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
vlan-based(1), port-based(2) |
|
swLoopDetectTrapMode |
1.3.6.1.4.1.171.12.41.1.5 |
This object indicates the loopback detection trap mode for the system. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
none(1), loop-detected(2), loop-cleared(3), both(4) |
|
swLoopDetectLogState |
1.3.6.1.4.1.171.12.41.1.6 |
This object indicates the LBD log state. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enabled(1), disabled(2) |
|
swLoopDetectPortEntry |
1.3.6.1.4.1.171.12.41.3.1.1 |
The table specifies the loopback detection function specified by port. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwLoopDetectPortEntry |
|
|
swLoopDetectPortIndex |
1.3.6.1.4.1.171.12.41.3.1.1.1 |
This object indicates the module's port number. The range is from 1 to
the maximum port number specified in the module |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..65535 |
|
swLoopDetectPortState |
1.3.6.1.4.1.171.12.41.3.1.1.2 |
This object indicates the loopback detection function state on the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enabled(1), disabled(2) |
|
swLoopDetectPortLoopStatus |
1.3.6.1.4.1.171.12.41.3.1.1.4 |
This object indicates the port status. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
normal(1), loop(2), error(3) |
|
swPortLoopOccurred |
1.3.6.1.4.1.171.12.41.10.0.1 |
The trap is sent when a port loop occurs. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
swPortLoopRestart |
1.3.6.1.4.1.171.12.41.10.0.2 |
The trap is sent when a port loop restarts after the interval time. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
swVlanLoopOccurred |
1.3.6.1.4.1.171.12.41.10.0.3 |
The trap is sent when a Port with a VID loop occurs. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
swVlanLoopRestart |
1.3.6.1.4.1.171.12.41.10.0.4 |
The trap is sent when a Port with a VID loop restarts after the interval time. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
swVlanLoopDetectVID |
1.3.6.1.4.1.171.12.41.10.1.1 |
This object indicates the VID that has detected a loopback. |
Status: current |
Access: accessible-for-notify |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|