Juniper-V35-MIB

File: Juniper-V35-MIB.mib (8227 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF IF-MIB
Juniper-MIBs

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
MODULE-COMPLIANCE OBJECT-GROUP InterfaceIndex
juniMibs

Defined Types

JuniV35IfEntry  
SEQUENCE    
  juniV35IfIndex InterfaceIndex
  juniV35IfType INTEGER
  juniV35IfMode INTEGER
  juniV35IfClockRate Unsigned32
  juniV35IfNrzEncoding INTEGER
  juniV35IfTxClock INTEGER
  juniV35IfIgnoreDcd INTEGER
  juniV35IfLoopback INTEGER

Defined Values

juniV35MIB 1.3.6.1.4.1.4874.2.2.59
The X.21/V.35 Server MIB for the Juniper Networks enterprise.
MODULE-IDENTITY    

juniV35Objects 1.3.6.1.4.1.4874.2.2.59.1
OBJECT IDENTIFIER    

juniV35IfTable 1.3.6.1.4.1.4874.2.2.59.1.2
This table contains entries for X.21/V.35 interfaces present in the system. This table provides an extension to the Juniper-HDLC-MIB.juniHdlcIfTable for HDLC interfaces that support X.21/V.35 signalling.
OBJECT-TYPE    
  SEQUENCE OF  
    JuniV35IfEntry

juniV35IfEntry 1.3.6.1.4.1.4874.2.2.59.1.2.1
Each entry describes the characteristics of an X.21/V.35 interface.
OBJECT-TYPE    
  JuniV35IfEntry  

juniV35IfIndex 1.3.6.1.4.1.4874.2.2.59.1.2.1.1
The ifIndex of the X.21/V.35 interface. It has the same value as the juniHdlcIfIndex for the common interface.
OBJECT-TYPE    
  InterfaceIndex  

juniV35IfType 1.3.6.1.4.1.4874.2.2.59.1.2.1.2
Read only parameter of interface type X.21/V.35.
OBJECT-TYPE    
  INTEGER x21(0), v35(1), interfaceTypeNoCable(2)  

juniV35IfMode 1.3.6.1.4.1.4874.2.2.59.1.2.1.3
Read only parameter of interface mode of interface X.21/V.35 Data Terminating Equipment(DTE)/Data Communication Equipment(DCE).
OBJECT-TYPE    
  INTEGER dte(0), dce(1), interfaceModeNoCable(2)  

juniV35IfClockRate 1.3.6.1.4.1.4874.2.2.59.1.2.1.4
The clock rate setting in hertz for this X.21/V.35 interface. Only the following values are valid: 1200, 2400, 4800, 9600, 19200, 38400, 56000, 64000, 128000, 1024000, 1536000, 2048000, 3072000, 4096000, 4915200, 6144000, and 8192000. If a value other than one of the predefined values is set, then the closest matching value is used. The clock rate parameter is only meaningful when the interface is in DCE mode. When the interface is in DTE mode, the value is simply ignored.
OBJECT-TYPE    
  Unsigned32  

juniV35IfNrzEncoding 1.3.6.1.4.1.4874.2.2.59.1.2.1.5
The non-return-to-zero (NRZ) encoding for X.21/V.35 interface. Inverted encoding is provided with NRZI-encoding command, which is non-return-to-zero inverted (NRZI) encoding.
OBJECT-TYPE    
  INTEGER normal(0), inverted(1)  

juniV35IfTxClock 1.3.6.1.4.1.4874.2.2.59.1.2.1.6
There is an option of inverting the transmit clock signal for X.21/V.35 interface. Inverting the tranmit clock is used to compensate for skews between the clock and data when transmitting across long cables at fast data rates.
OBJECT-TYPE    
  INTEGER normal(0), inverted(1)  

juniV35IfIgnoreDcd 1.3.6.1.4.1.4874.2.2.59.1.2.1.7
When in X.21/V.35 DTE mode we have the capability of ignoring the DCD signal in determining whether or not an interface is up.
OBJECT-TYPE    
  INTEGER ignoredNone(0), dcdIgnored(1), linkStateIgnored(2)  

juniV35IfLoopback 1.3.6.1.4.1.4874.2.2.59.1.2.1.8
Loopback interface is configured (or not) for X.21/V.35 interface
OBJECT-TYPE    
  INTEGER none(0), loopback(1)  

juniV35Conformance 1.3.6.1.4.1.4874.2.2.59.4
OBJECT IDENTIFIER    

juniV35Compliances 1.3.6.1.4.1.4874.2.2.59.4.1
OBJECT IDENTIFIER    

juniV35Groups 1.3.6.1.4.1.4874.2.2.59.4.2
OBJECT IDENTIFIER    

juniV35Compliance 1.3.6.1.4.1.4874.2.2.59.4.1.1
The compliance statement for entities that implement the Juniper X.21/V.35 MIB.
MODULE-COMPLIANCE    

juniV35Group 1.3.6.1.4.1.4874.2.2.59.4.2.1
A collection of objects providing management of X.21/V.35 interfaces in a Juniper product.
OBJECT-GROUP