Juniper-UNI-SONET-MIB
File:
Juniper-UNI-SONET-MIB.mib (43362 bytes)
Imported modules
Imported symbols
Defined Types
| JuniSonetLineSpeed |
|
| The set of SONET Line Speeds. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
sonetUnknownSpeed(0), sonetOc1Stm0(1), sonetOc3Stm1(2), sonetOc12Stm3(3), sonetOc48Stm16(4) |
|
| JuniSonetPathHierarchy |
|
| Represents textual information taken from the NVT ASCII character set.
The SONET path hierarchy is based upon the SONET line capacity.
Configuration examples follow the diagram below, which depicts the SONET
Path hierarchy.
OC-192/STM-64
^
|
OC-48/STM-16 (1-4)
^
|
OC-12/STM-4 (1-4)
^
|
OC-3/STM-1 (1-4)
^
|
OC-1/STM-0 (1-3)
^
|
^----------------^----------------^
| | |
DS3 (1) VT1.5/TU11 DS1 (1-28) VT2/TU12 (1-21)
For Line Speed = OC-48/STM-16:
When the entire capacity contains only one path, no specifier
is used.
OC-12/STM-4 Path
To specify an OC-12 path over OC-48 provide a single digit of
the form a where:
a - OC-12/STM-4 path number (1-4)
OC-3/STM-1 Path
To specify an OC-3 Path over OC-48 provide two digits of the
form a/b where:
a - OC-12/STM-4 path number (1-4)
b - OC-3/STM-1 path within the OC-12 (1-4)
OC-1/STM-0 Path
To specify an OC1 Path over OC-48 provide three digits of the
form a/b/c where:
a - OC-12/STM-4 path number (1-4)
b - OC-3/STM-1 path number within OC-12 (1-4)
c - OC-1/STM-0 path number within OC-3 (1-3)
For Line Speed = OC-12/STM-4:
OC-12/STM-4 Path:
When entire line capacity contains only one path, no
channel-specifier is used.
OC-3/STM-1 Path:
To specify an OC-3 path over OC-12 provide a single digit of
the form a where:
a - OC-3/STM-1 path within the OC-12 (1-4)
OC-1 Path:
To specify an OC-1 path over OC-12 provide two digits of the
form a/b where:
a - OC-3/STM-1 path within the OC-12 (1-4)
b - OC-1/STM-0 path within the OC-3 (1-3)
For Line Speed = OC-3/STM-1:
OC-3/STM-1 Path:
When entire line capacity contains only one path, no
channel-specifier is used.
OC-1 Path:
To specify an OC-1 path over OC-3 provide one digit of the
form a where:
a - OC-1/STM-1 path within the OC-3 (1-3) |
| TEXTUAL-CONVENTION |
|
|
|
| |
OCTET STRING |
Size(0..32) |
|
| JuniSonetPathC2ByteOverride |
|
| SONET Path c2 overhead byte.
This value should only be set in cases where the value set by
the upper interface type needs to be overridden. Standard values
are:
0 Unequipped
1 Nonspecific
2 Floating VT
4 Asyncronous mapping of DS3
19 ATM
22 HDLC over Sonet - scrambling enabled
207 HDLC over Sonet - no scrambling |
| TEXTUAL-CONVENTION |
|
|
|
| |
Integer32 |
0..255 |
|
| JuniSonetVTType |
|
| The SONET Virtual Tributary Type. This TC has been deprecated because
RFC2558 provides this information in SONET-MIB.sonetVTCurrentWidth. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
tribVT15TU11(0), tribVT20TU12(1), tribVT3(3), tribVT6(4), tribVT6c(5) |
|
| JuniSonetMediumEntry |
|
| SEQUENCE |
|
|
|
| |
juniSonetMediumType |
INTEGER |
|
| |
juniSonetMediumLoopbackConfig |
INTEGER |
|
| |
juniSonetMediumTimingSource |
INTEGER |
|
| |
juniSonetMediumCircuitIdentifier |
DisplayString |
|
| |
juniSonetMediumTriggerAlarms |
BITS |
|
| |
juniSonetMediumTriggerDelay |
Integer32 |
|
| JuniSonetPathCapabilityEntry |
|
| SEQUENCE |
|
|
|
| |
juniSonetPathRemoveFlag |
TruthValue |
|
| |
juniSonetPathChannelized |
TruthValue |
|
| |
juniSonetPathMaximumChannels |
Unsigned32 |
|
| |
juniSonetPathMinimumPathSpeed |
JuniSonetLineSpeed |
|
| |
juniSonetPathMaximumPathSpeed |
JuniSonetLineSpeed |
|
| JuniSonetPathEntry |
|
| SEQUENCE |
|
|
|
| |
juniSonetPathIfIndex |
InterfaceIndex |
|
| |
juniSonetPathLogicalChannel |
JuniSonetLogicalPathChannel |
|
| |
juniSonetPathSpeed |
JuniSonetLineSpeed |
|
| |
juniSonetPathHierarchy |
JuniSonetPathHierarchy |
|
| |
juniSonetPathLowerIfIndex |
InterfaceIndexOrZero |
|
| |
juniSonetPathRowStatus |
RowStatus |
|
| |
juniSonetPathTriggerAlarms |
BITS |
|
| |
juniSonetPathC2ByteOverrideFlag |
TruthValue |
|
| |
juniSonetPathC2ByteOverride |
JuniSonetPathC2ByteOverride |
|
| |
juniSonetPathTriggerDelay |
Integer32 |
|
| |
juniSonetPathEventStatus |
Unsigned32 |
|
| JuniSonetVTEntry |
|
| SEQUENCE |
|
|
|
| |
juniSonetVTIfIndex |
InterfaceIndex |
|
| |
juniSonetVTPathLogicalChannel |
JuniSonetLogicalPathChannel |
|
| |
juniSonetVTType |
JuniSonetVTType |
|
| |
juniSonetVTPathPayload |
Unsigned32 |
|
| |
juniSonetVTTributaryGroup |
Unsigned32 |
|
| |
juniSonetVTTributarySubChannel |
Unsigned32 |
|
| |
juniSonetVTLowerIfIndex |
InterfaceIndexOrZero |
|
| |
juniSonetVTRowStatus |
RowStatus |
|
Defined Values
| juniSonetMIB |
1.3.6.1.4.1.4874.2.2.7 |
| The SONET MIB for the Juniper Networks enterprise. This MIB contains
managed objects for SONET interfaces. It contains management objects
for configuration of interface attributes that either are absent from,
or read-only in the standard SONET-MIB. |
| MODULE-IDENTITY |
|
|
|
| juniSonetMediumTable |
1.3.6.1.4.1.4874.2.2.7.1.1 |
| This table contains entries for SONET interfaces present in the
system. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
JuniSonetMediumEntry |
|
| juniSonetMediumEntry |
1.3.6.1.4.1.4874.2.2.7.1.1.1 |
| Each entry describes the characteristics of an SONET interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JuniSonetMediumEntry |
|
|
| juniSonetMediumType |
1.3.6.1.4.1.4874.2.2.7.1.1.1.1 |
| This variable identifies whether a SONET or a SDH signal is used across
this interface. This object was deprecated because the same information
is provided by the SONET-MIB.sonetMediumType object (RFC 2558). |
| Status: deprecated |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
sonet(1), sdh(2) |
|
| juniSonetMediumLoopbackConfig |
1.3.6.1.4.1.4874.2.2.7.1.1.1.2 |
| The current loopback state of the SONET/SDH interface.
The values mean:
sonetNoLoop Not in the loopback state. A device that is not
capable of performing a loopback on this
interface shall always return this value.
sonetFacilityLoop The received signal at this interface is looped
back out through the corresponding transmitter in
the return direction.
sonetTerminalLoop The signal that is about to be transmitted is
connected to the associated incoming receiver.
sonetOtherLoop Loopbacks that are not defined here. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
sonetNoLoop(0), sonetFacilityLoop(1), sonetTerminalLoop(2), sonetOtherLoop(3) |
|
| juniSonetMediumTimingSource |
1.3.6.1.4.1.4874.2.2.7.1.1.1.3 |
| Selects the source from which transmit timing is derived.
loop timing is recovered from the receiver
internalModule timing is from the module associated with this
interface
internalChassis timing is taken from the internal system timing
reference |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
loop(0), internalModule(1), internalChassis(2) |
|
| juniSonetMediumCircuitIdentifier |
1.3.6.1.4.1.4874.2.2.7.1.1.1.4 |
| This variable contains the transmission vendor's circuit identifier,
for the purpose of facilitating troubleshooting. This object was
deprecated because the same information is provided by the
SONET-MIB.sonetMediumCircuitIdentifier object (RFC 2558). |
| Status: deprecated |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| juniSonetMediumTriggerAlarms |
0.0.2.3.1.3.6.1.4.1.4874.2.2.7.1.1.1.5 |
| The alarms that are used in the operational status calculation for this
SONET interface.
sectionLOS When this bit is set, section LOS is used for
operational status calculation.
sectionLOF When this bit is set, section LOF is used for
operational status calculation.
lineAIS When this bit is set, line AIS is used for operational
status calculation.
lineRDI When this bit is set, line RDI is used for operational
status calculation.
The value of this object defaults to all the bits set, indicating all of
the alarms are used for the operational status calculation. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BITS |
sectionLOS(0), sectionLOF(1), lineAIS(2), lineRDI(3) |
|
| juniSonetMediumTriggerDelay |
1.3.6.1.4.1.4874.2.2.7.1.1.1.6 |
| The time delay (in milliseconds) before a defect is accepted as an
alarm for this SONET interface. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..2500 |
|
| juniSonetPathCapabilityEntry |
1.3.6.1.4.1.4874.2.2.7.2.1.1 |
| Each entry describes the SONET path capability of a SONET interface.
This table is index by the ifIndex of the SONET interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JuniSonetPathCapabilityEntry |
|
|
| juniSonetPathRemoveFlag |
1.3.6.1.4.1.4874.2.2.7.2.1.1.1 |
| This variable identifies whether a SONET/SDH supports the deletion of
SONET Paths. A value of true(1) indicates the SONET path is removable;
a value of false(2) indicates the SONET path cannot be removed. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| juniSonetPathChannelized |
1.3.6.1.4.1.4874.2.2.7.2.1.1.2 |
| Identifies whether or not this SONET interface supports channelization.
A value of true(1) indicates the SONET path is channelized; a value of
false(2) indicates the SONET path is not channelized. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| juniSonetPathMaximumChannels |
1.3.6.1.4.1.4874.2.2.7.2.1.1.3 |
| Identifies the maximum number of SONET paths/channels for this
interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| juniSonetPathNextIfIndex |
1.3.6.1.4.1.4874.2.2.7.2.2 |
| Coordinate ifIndex value allocation for entries in juniSonetPathTable.
A GET of this object returns the next available ifIndex value to be used
to create an entry in the associated interface table; or zero, if no
valid ifIndex value is available. This object also returns a value of
zero when it is the lexicographic successor of a varbind presented in an
SNMP GETNEXT or GETBULK request, for which circumstance it is assumed
that ifIndex allocation is unintended.
Successive GETs will typically return different values, thus avoiding
collisions among cooperating management clients seeking to create table
entries simultaneously. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
JuniNextIfIndex |
|
|
| juniSonetPathTable |
1.3.6.1.4.1.4874.2.2.7.2.3 |
| This table contains entries for SONET Path interfaces present in the
system. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
JuniSonetPathEntry |
|
| juniSonetPathEntry |
1.3.6.1.4.1.4874.2.2.7.2.3.1 |
| Each entry describes the characteristics of an SONET Path interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JuniSonetPathEntry |
|
|
| juniSonetPathIfIndex |
1.3.6.1.4.1.4874.2.2.7.2.3.1.1 |
| The ifIndex of the SONET Path interface. When creating entries in this
table, suitable values for this object are determined by reading
juniSonetPathNextIfIndex. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| juniSonetPathLogicalChannel |
1.3.6.1.4.1.4874.2.2.7.2.3.1.2 |
| The logical channel number assigned to this SONET Path. If the
underlying SONET interface does not support channelization, the value of
this object is zero. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
JuniSonetLogicalPathChannel |
|
|
| juniSonetPathLowerIfIndex |
1.3.6.1.4.1.4874.2.2.7.2.3.1.5 |
| The ifIndex of the interface over which this SONET Path interface is to
be layered - typically a SONET/SDH interface. A value of zero indicates
no layering. An implementation may choose to require that a nonzero
value be configured at entry creation. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndexOrZero |
|
|
| juniSonetPathRowStatus |
1.3.6.1.4.1.4874.2.2.7.2.3.1.6 |
| Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
juniSonetPathRowStatus
juniSonetPathSpeed
juniSonetPathHierarchy
juniSonetPathLowerIfIndex
The logical channel may optionally be specified. If it is not specified
an unused logical channel value will be assigned by the system.
juniSonetPathLogicalChannel
In addition, when creating an entry the following conditions must hold:
A value for juniSonetPathIfIndex must have been determined
previously, by reading juniSonetPathNextIfIndex.
The interface identified by the juniSonetPathLowerIfIndex must
exist.
The juniSonetPathSpeed must be consistent with the speed for the
channel specified by the juniSonetPathHierarchy, based on the speed
of the interface identified by the juniSonetPathLowerIfIndex.
A corresponding entry in ifTable/ifXTable/juniIfTable is created/
destroyed as a result of creating/destroying an entry in this table. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| juniSonetPathTriggerAlarms |
0.1.1.3.6.1.4.1.4874.2.2.7.2.3.1.7 |
| The path alarms that are used in the operational status calculation for
this SONET Path.
pathLOP When this bit is set, path LOP is used for operational
status calculation. This bit may not be modified.
pathAIS When this bit is set, path AIS is used for operational
status calculation. This bit may not be modified.
pathRDI When this bit is set, path RDI is used for operational
status calculation.
The value of this object defaults to bits 0 and 1 set, indication LOP
and AIS will be used for operational status calculation this SONET
Path. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
BITS |
pathLOP(0), pathAIS(1), pathRDI(2) |
|
| juniSonetPathC2ByteOverrideFlag |
1.3.6.1.4.1.4874.2.2.7.2.3.1.8 |
| The path overhead c2 transmit override enable. If set to true(1),
juniSonetPathC2Byte override value must be specified. If set to
false(2), c2 byte will be automatically set by the system based on the
upper interface type. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| juniSonetPathTriggerDelay |
1.3.6.1.4.1.4874.2.2.7.2.3.1.10 |
| The time delay (in milliseconds) before a defect is accepted as an
alarm for this SONET Path. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..2500 |
|
| juniSonetPathEventStatus |
1.3.6.1.4.1.4874.2.2.7.2.3.1.11 |
| This variable specifies which events have occurred in the current 15
minute interval. The value represents a vector of bits, each specifying
a unique event:
- Bit 0 Rising threshold alarm, sonetPathCurrentESs.
- Bit 1 Rising threshold alarm, sonetPathCurrentSESs.
- Bit 2 Reserved.
- Bit 3 Rising threshold alarm, sonetPathCurrentCVs.
- Bit 4 Rising threshold alarm, sonetPathCurrentUASs.
- Bit 5 LOP failure indication.
- Bit 6 LOP failure cleared.
- Bit 7 AIS failure indication.
- Bit 8 AIS failure cleared.
- Bit 9 RFI indication.
- Bit 10 RFI cleared.
- Bit 11 UNEQ failure indication.
- Bit 12 UNEQ failure cleared.
- Bit 13 PLM failure indication.
- Bit 14 PLM failure cleared. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..32767 |
|
| juniSonetVTNextIfIndex |
1.3.6.1.4.1.4874.2.2.7.3.1 |
| Coordinate ifIndex value allocation for entries in juniSonetVTTable.
A GET of this object returns the next available ifIndex value to be used
to create an entry in the associated interface table; or zero, if no
valid ifIndex value is available. This object also returns a value of
zero when it is the lexicographic successor of a varbind presented in an
SNMP GETNEXT or GETBULK request, for which circumstance it is assumed
that ifIndex allocation is unintended.
Successive GETs will typically return different values, thus avoiding
collisions among cooperating management clients seeking to create table
entries simultaneously. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
JuniNextIfIndex |
|
|
| juniSonetVTTable |
1.3.6.1.4.1.4874.2.2.7.3.2 |
| This table contains entries for SONET Virtual Tributary interfaces
present in the system. This table augments the standard
SONET-MIB.sonetVTCurrentTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
JuniSonetVTEntry |
|
| juniSonetVTEntry |
1.3.6.1.4.1.4874.2.2.7.3.2.1 |
| Each entry describes the characteristics of an SONET Virtual Tributary
interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JuniSonetVTEntry |
|
|
| juniSonetVTIfIndex |
1.3.6.1.4.1.4874.2.2.7.3.2.1.1 |
| The ifIndex of the SONET Virtual Tributary interface. When creating
entries in this table, suitable values for this object are determined by
reading juniSonetVTNextIfIndex. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| juniSonetVTType |
1.3.6.1.4.1.4874.2.2.7.3.2.1.3 |
| The SONET virtual tributary type. This object was deprecated because
the same information is provided in the SONET-MIB.sonetVTCurrentWidth
object. |
| Status: deprecated |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
JuniSonetVTType |
|
|
| juniSonetVTPathPayload |
1.3.6.1.4.1.4874.2.2.7.3.2.1.4 |
| The SONET Path payload number associated with this virtual tributary.
For SDH mode, this is a value with a range from 1-3. For SONET mode,
the value of this object is always 1. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| juniSonetVTTributaryGroup |
1.3.6.1.4.1.4874.2.2.7.3.2.1.5 |
| The SONET Path group number for this virtual tributary. In SONET and
SDH mode, the value of this object is 1-7. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| juniSonetVTTributarySubChannel |
1.3.6.1.4.1.4874.2.2.7.3.2.1.6 |
| Specifies the virtual tributary number within the tributary group
defined by juniSonetVTTributaryGroup object. The value of this object
ranges from 1-4 if the tributary type is tribVT15/TU11(0); and the
values 1-3 if the tributary type is tribVT20/TU12(1). |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| juniSonetVTLowerIfIndex |
1.3.6.1.4.1.4874.2.2.7.3.2.1.7 |
| The ifIndex of the interface over which this SONET Virtual Tributary
interface is to be layered - typically a SONET PATH interface.
A value of zero indicates no layering. An implementation may choose to
require that a nonzero value be configured at entry creation. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndexOrZero |
|
|
| juniSonetVTRowStatus |
1.3.6.1.4.1.4874.2.2.7.3.2.1.8 |
| Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
juniSonetVTRowStatus
juniSonetVTPathLogicalChannel
juniSonetVTType
juniSonetVTPathPayload
juniSonetVTTributaryGroup
juniSonetVTTributarySubChannel
juniSonetVTLowerIfIndex
In addition, when creating an entry the following conditions must hold:
A value for juniSonetVTIfIndex must have been determined previously,
by reading juniSonetVTNextIfIndex.
The interface identified by juniSonetVTLowerIfIndex must exist.
A corresponding entry in ifTable/ifXTable/juniIfTable is created/
destroyed as a result of creating/destroying an entry in this table. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| juniSonetPathEventIfIndex |
1.3.6.1.4.1.4874.2.2.7.5.1 |
| The ifIndex of the SONET Path interface. This is the same value as
juniSonetPathIfIndex for the interface that is reporting an event. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| juniSonetPathEvents |
1.3.6.1.4.1.4874.2.2.7.6.0.1 |
| This trap reports SONET path events for the failures and normal
conditions of the SONET path entity. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| juniSonetCompliance |
1.3.6.1.4.1.4874.2.2.7.4.1.1 |
| Obsolete compliance statement for entities which implement the Juniper
SONET MIB. This statement became obsolete when the SONET Path and SONET
VT groups of objects were added. |
| Status: obsolete |
Access: accessible-for-notify |
| MODULE-COMPLIANCE |
|
|
|
| juniSonetCompliance2 |
1.3.6.1.4.1.4874.2.2.7.4.1.2 |
| Obsolete compliance statement for entities which implement the Juniper
SONET MIB. This statement became obsolete when the juniSonetMediumType,
juniSonetMediumCircuitIdentifier and juniSonetVTType objects were
deprecated. |
| Status: obsolete |
Access: accessible-for-notify |
| MODULE-COMPLIANCE |
|
|
|
| juniSonetCompliance3 |
1.3.6.1.4.1.4874.2.2.7.4.1.3 |
| Obsolete compliance statement for entities which implement the Juniper
SONET MIB. This statement became obsolete when support was added for
alarm triggers and path c2 byte override. |
| Status: obsolete |
Access: accessible-for-notify |
| MODULE-COMPLIANCE |
|
|
|
| juniSonetCompliance4 |
1.3.6.1.4.1.4874.2.2.7.4.1.4 |
| Obsolete compliance statement for entities which implement the Juniper
SONET MIB. This statement became obsolete when the SONET Path event
status and notification support was added. |
| Status: obsolete |
Access: accessible-for-notify |
| MODULE-COMPLIANCE |
|
|
|
| juniSonetCompliance5 |
1.3.6.1.4.1.4874.2.2.7.4.1.5 |
| The compliance statement for entities which implement the Juniper SONET
MIB. |
| Status: current |
Access: accessible-for-notify |
| MODULE-COMPLIANCE |
|
|
|
| juniSonetGroup |
1.3.6.1.4.1.4874.2.2.7.4.2.1 |
| Obsolete collection of objects providing management of SONET/SDH
interfaces in a Juniper product. This group became obsolete when the
juniSonetMediumType and juniSonetMediumCircuitIdentifier objects were
deprecated. |
| Status: obsolete |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetPathGroup |
1.3.6.1.4.1.4874.2.2.7.4.2.2 |
| Obsolete collection of objects providing management of SONET/SDH Path
interfaces in a Juniper product. This group became obsolete when new
SONET path objects were added. |
| Status: obsolete |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetVirtualTributaryGroup |
1.3.6.1.4.1.4874.2.2.7.4.2.3 |
| Obsolete collection of objects providing management of SONET virtual
tributaries in a Juniper product. This group became obsolete when
juniSonetVTType was deprecated. |
| Status: obsolete |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetGroup2 |
1.3.6.1.4.1.4874.2.2.7.4.2.4 |
| Obsolete collection of objects providing management of SONET/SDH
interfaces in a Juniper product. This group became obsolete when
juniSonetMediumTriggerAlarms was added. |
| Status: obsolete |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetVirtualTributaryGroup2 |
1.3.6.1.4.1.4874.2.2.7.4.2.5 |
| A collection of objects providing management of SONET virtual
tributaries in a Juniper product. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetDeprecatedMediumGroup |
1.3.6.1.4.1.4874.2.2.7.4.2.6 |
| A collection of deprecated objects providing management of SONET/SDH
interfaces in a Juniper product. This group is deprecated because the
same information is provided by SONET-MIB objects (RFC 2558). Support
for the objects in this group will be phased out over time. |
| Status: deprecated |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetDeprecatedVTGroup |
1.3.6.1.4.1.4874.2.2.7.4.2.7 |
| A deprecated object providing management of SONET/SDH VT interfaces in
a Juniper product. This group is deprecated because the same
information is provided by SONET-MIB objects (RFC 2558). Support for
the VT type object will be phased out over time. |
| Status: deprecated |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetGroup3 |
1.3.6.1.4.1.4874.2.2.7.4.2.8 |
| A collection of objects providing management of SONET/SDH interfaces in
a Juniper product. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetPathGroup2 |
1.3.6.1.4.1.4874.2.2.7.4.2.9 |
| Obsolete collection of management objects providing management of
SONET/SDH Path interfaces in a Juniper product. This group became
obsolete when path event notification support was added. |
| Status: obsolete |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetPathGroup3 |
1.3.6.1.4.1.4874.2.2.7.4.2.10 |
| A collection of objects providing management of SONET/SDH Path
interfaces in a Juniper product. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| juniSonetPathNotificationGroup |
1.3.6.1.4.1.4874.2.2.7.4.2.11 |
| A management notification for signaling SONET Path interface status
changes in a Juniper product. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-GROUP |
|
|
|