Juniper-SNMP-MIB

File: Juniper-SNMP-MIB.mib (64881 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB Juniper-TC Juniper-MIBs

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
Counter32 IpAddress Unsigned32
TEXTUAL-CONVENTION RowStatus TruthValue
MODULE-COMPLIANCE OBJECT-GROUP SnmpAdminString
JuniEnable juniMibs

Defined Types

JuniSnmpCommunityName  
An SNMP community name. Represents textual information taken from the NVT ASCII character set. The character repertoire of the string is restricted to printable, non-whitespace characters (codes 33 through 126).
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..31)  

JuniSnmpAccessListName  
An IP Access List name. Represents textual information taken from the NVT ASCII character set. The character repertoire of the string is restricted to printable, non-whitespace characters (codes 33 through 126).
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..31)  

JuniSnmpTrapMask  
This octet string is interpreted as a bit mask, in which each bit corresponds to a category of SNMP trap. Bit definitions are as follows, where bit 63 is the most significant bit of the first octet, and bit 0 is the least significant bit of the eighth octet: Bit Category ----- ----------------------------------------------- 0 SNMP standard coldStart/warmStart/authenticationFailure traps 1 Standard linkUp/linkDown traps 2 Platform inventory traps 3 Environment (power, temperature, fan and memory) traps 4 Accounting (bulk statistics) traps 5 File transfer status trap 6 BGP traps 7 Log configuration traps 8 CLI security alert trap 9 Ping traps 10 OSPF traps 11 TraceRoute traps 12 Standard DVMRP traps 13 Proprietary DVMRP trap 14 Local address pool traps 15 ATM ping traps 16 VRRP traps 17 SONET layer traps 18 NTP traps 19 Radius clients trap 20 DisMan Event traps 21 DHCP traps 22 PIM traps 23 High Availability Redundancy traps 24 Route Table traps 25 IP Traps 26 Mirror Traps 27 Vpn Traps 28 Bfd Traps 29 Dos Protection Platform Traps 30 Mrouter Traps 31 Ldp Traps 32 Mobile IPv4 Traps 33 ISSU Traps 34-63 Undefined.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

JuniTrapSeverity  
The set of trap severity values: trapEmergency(0) - system is unusable trapAlert(1) - action must be taken immediately trapCritical(2) - critical conditions trapError(3) - error conditions trapWarning(4) - warning conditions trapNotice(5) - normal but significant condition trapInformational(6) - informational messages trapDebug(7) - debug-level messages
TEXTUAL-CONVENTION    
  INTEGER trapEmergency(0), trapAlert(1), trapCritical(2), trapError(3), trapWarning(4), trapNotice(5), trapInformational(6), trapDebug(7)  

JuniSnmpIntfCompRestrictedMask  
This octet string is interpreted as a bit mask, in which each bit corresponds to an interface restriction. The DESCRIPTION clause of a MIB object having this SYNTAX should specify the semantics of bit values '1' and '0'. Bit definitions are as follows, where bit 31 is the most significant bit of the first octet, and bit 0 is the least significant bit of the fourth octet: Bit interface restriction ----- ----------------------------------------------- 0 ifAdminStatus Down 1-31 Undefined.
TEXTUAL-CONVENTION    
  OCTET STRING Size(4)  

JuniSnmpManagementApplicationIndex  
Identifies a management application: eventMgr - disman event MIB application
TEXTUAL-CONVENTION    
  INTEGER eventMgr(1)  

JuniSnmpIntfCompEntry  
SEQUENCE    
  juniSnmpIntfCompTableType INTEGER
  juniSnmpIntfCompEntryCompressed TruthValue
  juniSnmpIntfCompMask OCTET STRING
  juniSnmpIntfCompMaskDisplay OCTET STRING

JuniSnmpManagementApplicationEntry  
SEQUENCE    
  juniSnmpManagementApplicationRouterIndex Unsigned32
  juniSnmpManagementApplicationIndex JuniSnmpManagementApplicationIndex
  juniSnmpManagementApplicationRowStatus RowStatus

JuniSnmpCommunityEntry  
SEQUENCE    
  juniSnmpCommunityName JuniSnmpCommunityName
  juniSnmpCommunityRowStatus RowStatus
  juniSnmpCommunityPrivilege INTEGER
  juniSnmpCommunityAccessList Integer32
  juniSnmpCommunityAccessListName JuniSnmpAccessListName
  juniSnmpCommunityView SnmpAdminString

JuniSnmpTrapHostEntry  
SEQUENCE    
  juniSnmpTrapHostIpAddress IpAddress
  juniSnmpTrapHostRowStatus RowStatus
  juniSnmpTrapHostUdpPort Integer32
  juniSnmpTrapHostCommunity JuniSnmpCommunityName
  juniSnmpTrapHostProtocolVersion INTEGER
  juniSnmpTrapHostFilter JuniSnmpTrapMask
  juniSnmpTrapHostSends Counter32
  juniSnmpTrapHostDiscards Counter32
  juniSnmpTrapHostSeverityFilter JuniTrapSeverity
  juniSnmpTrapHostPingTimeOut Integer32
  juniSnmpTrapHostIncludeLogVarbinds TruthValue
  juniSnmpTrapHostQueueSize Integer32
  juniSnmpTrapHostQueueDrainRate Integer32
  juniSnmpTrapHostQueueFull INTEGER
  juniSnmpTrapHostBadEncodingDiscards Counter32
  juniSnmpTrapHostQueueFullDiscards Counter32
  juniSnmpTrapHostNoResponseDiscards Counter32

JuniSnmpTrapSeverityFilterEntry  
SEQUENCE    
  juniSnmpTrapCategory Integer32
  juniSnmpTrapSeverityFilter JuniTrapSeverity

Defined Values

juniSnmpMIB 1.3.6.1.4.1.4874.2.2.16
MIB objects for configuring SNMP-based management access into Juniper E-series products.
MODULE-IDENTITY    

juniSnmpObjects 1.3.6.1.4.1.4874.2.2.16.1
OBJECT IDENTIFIER    

juniSnmpConformance 1.3.6.1.4.1.4874.2.2.16.2
OBJECT IDENTIFIER    

juniSnmpGeneral 1.3.6.1.4.1.4874.2.2.16.1.1
OBJECT IDENTIFIER    

juniSnmpInterfaceCompress 1.3.6.1.4.1.4874.2.2.16.1.1.3
OBJECT IDENTIFIER    

juniSnmpCommunity 1.3.6.1.4.1.4874.2.2.16.1.2
OBJECT IDENTIFIER    

juniSnmpTrap 1.3.6.1.4.1.4874.2.2.16.1.3
OBJECT IDENTIFIER    

juniSnmpAuthFailId 1.3.6.1.4.1.4874.2.2.16.1.4
OBJECT IDENTIFIER    

juniSnmpMaxPduSize 1.3.6.1.4.1.4874.2.2.16.1.1.1
The maximum sized SNMP PDU, in bytes, that this agent is capable of handling. The default is 1500 bytes. The possibility of IP fragmentation should be considered when setting this object to large values.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 484..8192  

juniSnmpInterfaceMode 1.3.6.1.4.1.4874.2.2.16.1.1.2
The interface table mode for the SNMP agent(s) associated with this system. verbose(1) - the standard ifTable, ifXTable and ifStackTable contain entries for every standard and proprietary interface type supported by this system. compress(2) - the standard ifTable, ifXTable and ifStackTable contain a subset of interface types. Certain interface types like HDLC and IP and others are excluded from the standard tables but are manageable from proprietary MIBs. enhanced(3) - the standard ifTable, ifXTable and ifStackTable contain a subset of interface types. Enhanced mode cannot by configured at this time via SNMP. Attempts to set this value will fail. This object became obsolete when individual objects were added for each mode.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER verbose(1), compress(2), enhanced(3)  

juniSnmpProxyStatus 1.3.6.1.4.1.4874.2.2.16.1.1.4
Enable/disable SNMP proxy between virtual routers.
Status: current Access: read-write
OBJECT-TYPE    
  JuniEnable  

juniSnmpAccessPermission 1.3.6.1.4.1.4874.2.2.16.1.1.5
The access permission to the MIB objects of this SNMP agent. noAccess - No access permission granted. readAccess - Read access permission granted. readWriteAccess - Read and write access permission granted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAccess(1), readAccess(2), readWriteAccess(3)  

juniSnmpIntfCompCompressed 1.3.6.1.4.1.4874.2.2.16.1.1.3.1
true(1) - the standard ifTable, ifXTable and ifStackTable contain a subset of interface types. Certain interface types like HDLC and IP and others are excluded from the standard tables but are manageable from proprietary MIBs. false(2) - the standard ifTable, ifXTable and ifStackTable contain entries for every standard and proprietary interface type supported by this system. This configuration is applicable to all interface related tables until interface compression based on interface table-types is applied. If interface table-type based compression is applied, get operation on this object will correspond only to ifTable/ifXTable/juniIfTable and set operation on this object will fail.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniSnmpIntfCompEnhanced 1.3.6.1.4.1.4874.2.2.16.1.1.3.2
This object governs which interface types are visible to SNMP management clients that use the standard ifTable, ifXTable and ifStackTable. The object is a variable length octet string that is interpreted as a bit mask. Each bit respresents a specific Juniper interface type that can be included or excluded in the standard interface tables. For each bit position in each octet of the string, a '1' or '0' indicates the corresponding interface type is either removed (compressed) from the standard interface MIB tables, or included respectively. Individual bit definitions follow the JuniIfType convention defined in the Juniper-UNI-IF-MIB. For example, ip(0) and ppp(1) correspond to bit definitions 0 and 1 respectively. In each octet, bit 0 is least significant, bit 7 most significant. This configuration is applicable to all interface related tables until interface compression based on interface table-types is applied. If interface table-type based compression is applied, get operation on this object will correspond only to ifTable/ifXTable/juniIfTable and set operation on this object will fail.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(5..16)  

juniSnmpIntfCompEnhancedDisplay 1.3.6.1.4.1.4874.2.2.16.1.1.3.3
This object displays the excluded interface types in human readable form. Three dots (...) at the end of display string indicates that the output has been truncated. The syntax rules are the same as for SNMP-FRAMEWORK-MIB.SnmpAdminString, except for the size constraint. This configuration is applicable to all interface related tables until interface compression based on interface table-types is applied. If interface table-type based compression is applied, this object will be applicable only to ifTable/ifXTable/juniIfTable.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1000)  

juniSnmpIntfCompRestricted 1.3.6.1.4.1.4874.2.2.16.1.1.3.4
This object governs which interface instances appear to SNMP management clients that use the standard ifTable, ifXTable and ifStackTable. The control is based on a set of interface restrictions defined by JuniSnmpInterfaceModeRestrictedMask. For each bit position in each octet of the string, a '1' or '0' controls whether an interface instance that matches the restriction is removed or included in the standard interface MIB tables. For example, setting the value of this object to 1 will remove all interface instances with an ifAdminStatus of down(2). In each octet, bit 0 is least significant, bit 7 most significant.
Status: current Access: read-write
OBJECT-TYPE    
  JuniSnmpIntfCompRestrictedMask  

juniSnmpIntfCompRestrictedDisplay 1.3.6.1.4.1.4874.2.2.16.1.1.3.5
This object displays the restrictions in human readable form. Three dots (...) at the end of display string indicates that the output has been truncated.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..100)  

juniSnmpIntfCompTable 1.3.6.1.4.1.4874.2.2.16.1.1.3.6
This table contains enhanced compression bitmask based on table-type.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniSnmpIntfCompEntry

juniSnmpIntfCompEntry 1.3.6.1.4.1.4874.2.2.16.1.1.3.6.1
Each entry corresponds to a table type for which interface compression mask is applied.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniSnmpIntfCompEntry  

juniSnmpIntfCompTableType 1.3.6.1.4.1.4874.2.2.16.1.1.3.6.1.1
SNMP interface tables for which interface compression bitmask will be applicable. Supported values are: others : All the other interface related tables except ifTables and ifStackTables. Currently only ipNetToMediaTable is supported. ifTables : It consists of ifTable, ifXTable and juniIfTable. ifStackTables : It consists of ifStackTable, ifInvStackTable and juniIfInvStackTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER others(0), ifTables(1), ifStackTables(2)  

juniSnmpIntfCompEntryCompressed 1.3.6.1.4.1.4874.2.2.16.1.1.3.6.1.2
true(1) - the standard ifTable, ifXTable and ifStackTable contain a subset of interface types. Certain interface types like HDLC and IP and others are excluded from the standard tables but are manageable from proprietary MIBs. false(2) - the standard ifTable, ifXTable and ifStackTable contain entries for every standard and proprietary interface type supported by this system.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniSnmpIntfCompMask 1.3.6.1.4.1.4874.2.2.16.1.1.3.6.1.3
This object governs which interface types are visible to SNMP management clients. The object is a variable length octet string that is interpreted as a bit mask. Each bit respresents a specific Juniper interface type that can be included or excluded in the standard interface tables. For each bit position in each octet of the string, a '1' or '0' indicates the corresponding interface type is either filtered (compressed) from the interface MIB tables, or included respectively. Individual bit definitions follow the JuniIfType convention defined in the Juniper-UNI-IF-MIB. For example, ip(0) and ppp(1) correspond to bit definitions 0 and 1 respectively. In each octet, bit 0 is least significant, bit 7 most significant.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(5..16)  

juniSnmpIntfCompMaskDisplay 1.3.6.1.4.1.4874.2.2.16.1.1.3.6.1.4
This object displays the excluded interface types in human readable form. Three dots (...) at the end of display string indicates that the output has been truncated. The syntax rules are the same as for SNMP-FRAMEWORK-MIB.SnmpAdminString, except for the size constraint.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1000)  

juniSnmpManagementApplicationTable 1.3.6.1.4.1.4874.2.2.16.1.1.6
This table contains entries for each management application supported by the router entry created in the juniRouterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniSnmpManagementApplicationEntry

juniSnmpManagementApplicationEntry 1.3.6.1.4.1.4874.2.2.16.1.1.6.1
Each entry provides administrative control on a management application for the router designated by the first indice to this table. The second indice identifies the router management application. Entries in this table are created as a side-effect of row creation in the juniRouterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniSnmpManagementApplicationEntry  

juniSnmpManagementApplicationRouterIndex 1.3.6.1.4.1.4874.2.2.16.1.1.6.1.1
The routerIndex of this router. This object is the same as the juniRouterIndex object defined in the juniRouterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniSnmpManagementApplicationIndex 1.3.6.1.4.1.4874.2.2.16.1.1.6.1.2
Identities the management application.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniSnmpManagementApplicationIndex  

juniSnmpManagementApplicationRowStatus 1.3.6.1.4.1.4874.2.2.16.1.1.6.1.3
Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniSnmpCommunityTable 1.3.6.1.4.1.4874.2.2.16.1.2.1
Table of SNMP management clients. Authentic SNMP clients are identified by a combination community name and IP address. Upon receipt of an SNMP request, this table is scanned for a matching community name. If an entry containing a matching community name is found, the entry's IP access list, if nonzero, is used to validate the source IP address received in the request; else, if the IP access list number in the matching entry is zero, the source IP address is accepted. Finally, the type of SNMP request is validated with respect to the access privilege of the matching entry (e.g. a SET Request is rejected for an entry having read-only privilege). Use of this table constitutes 'trivial authentication', i.e., no mechanism is employed to confirm the received SNMP request was indeed originated by the host identified by the IP source address.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniSnmpCommunityEntry

juniSnmpCommunityEntry 1.3.6.1.4.1.4874.2.2.16.1.2.1.1
A table entry describing an authentic SNMP Community.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniSnmpCommunityEntry  

juniSnmpCommunityName 1.3.6.1.4.1.4874.2.2.16.1.2.1.1.1
An SNMP community name.
Status: current Access: read-only
OBJECT-TYPE    
  JuniSnmpCommunityName  

juniSnmpCommunityRowStatus 1.3.6.1.4.1.4874.2.2.16.1.2.1.1.2
Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniSnmpCommunityPrivilege 1.3.6.1.4.1.4874.2.2.16.1.2.1.1.3
The access privilege for an SNMP Community authenticated by this entry (used in conjunction with MIB view as specified via juniSnmpCommunityView). readOnly Read-only access to MIB with associated view. readWrite Read-write access to MIB with associated view. admin Read-write access to entire MIB (for backward compatibility, automatically defaults to 'everything' view and 'readWrite' privilege).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER readOnly(1), readWrite(2), admin(3)  

juniSnmpCommunityAccessList 1.3.6.1.4.1.4874.2.2.16.1.2.1.1.4
If nonzero, the number of an IP access list that describes the IP hosts permitted SNMP management access to this device via the corresponding community name contained in this entry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..10000  

juniSnmpCommunityAccessListName 1.3.6.1.4.1.4874.2.2.16.1.2.1.1.5
If not null, the name of an IP access list that describes the IP hosts permitted SNMP management access to this device via the corresponding community name contained in this entry.
Status: current Access: read-create
OBJECT-TYPE    
  JuniSnmpAccessListName  

juniSnmpCommunityView 1.3.6.1.4.1.4874.2.2.16.1.2.1.1.6
The view associated with an SNMP Community authenticated by this entry. Following is the list of built-in system views. everything Access to the entire MIB except packet mirror MIB. user Access to non-administrative portions of MIB. nothing No access. mirrorAdmin Access to packet mirror MIB. 'Administrative' portions of the MIB are those portions that pertain to management access into the managed device. Administrator can also create a new SNMP MIB view dynamically and assign it to community entry. Access to packet mirror MIB is only thorugh 'mirrorAdmin' view. A community with 'mirrorAdmin' view can be configure only through CLI administrator with mirror configuration privileges.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

juniSnmpTrapGlobalFilter 1.3.6.1.4.1.4874.2.2.16.1.3.1
This object provides global control over trap generation by this agent. For each bit position, a '1' or '0' indicates the corresponding trap category is enabled or disabled, respectively. For security reasons, 'Mirror' category will not be allowed to be configured through SNMP.
Status: current Access: read-write
OBJECT-TYPE    
  JuniSnmpTrapMask  

juniSnmpTrapSource 1.3.6.1.4.1.4874.2.2.16.1.3.2
The ifIndex of the interface whose IP address is used as the source IP address for outbound SNMP traps. If zero, no interface is specified, the mechanism for selecting a source IP address is implementation-dependent, and may vary with each trap sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..2147483647  

juniSnmpTrapHostTable 1.3.6.1.4.1.4874.2.2.16.1.3.3
Table of SNMP Trap recipient.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniSnmpTrapHostEntry

juniSnmpTrapHostEntry 1.3.6.1.4.1.4874.2.2.16.1.3.3.1
A table entry describing an SNMP Trap recipient.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniSnmpTrapHostEntry  

juniSnmpTrapHostIpAddress 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.1
IP address of an authorized SNMP Trap recipient. This must be a host IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniSnmpTrapHostRowStatus 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.2
Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniSnmpTrapHostUdpPort 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.3
The destination UDP port to which traps will be sent.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniSnmpTrapHostCommunity 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.4
An SNMP community name to be used in traps sent to this destination.
Status: current Access: read-create
OBJECT-TYPE    
  JuniSnmpCommunityName  

juniSnmpTrapHostProtocolVersion 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.5
The format of the SNMP trap PDU to be sent to this trap destination. v1 Trap-PDU defined in RFC1157, encapsulated in the message structure also defined in RFC1157. v2c SNMPv2-Trap-PDU defined in RFC1905, encapsulated in the message structure defined in RFC1901. v3 SNMPv2-Trap-PDU defined in RFC1905, encapsulated in the message structure defined in RFC2571.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER v1(0), v2c(1), v3(2)  

juniSnmpTrapHostFilter 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.6
Bit mask designating the specific trap types enabled for transmission to this trap destination. For each bit position, a '1' or '0' indicates the corresponding trap type is enabled or disabled, respectively. For security reasons, 'Mirror' category will not be allowed to be configured through SNMP. Note, trap generation is further constrained by the value juniSnmpTrapGlobalFilter.
Status: current Access: read-create
OBJECT-TYPE    
  JuniSnmpTrapMask  

juniSnmpTrapHostSends 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.7
The number of traps submitted for transmission to this destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapHostDiscards 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.8
The number of trap requests that were discarded. A trap may be discarded because the trap type is either not a configured type in juniSnmpTrapHostFilter, or because the traps's priority is below the minimum trap severity filter defined by juniSnmpTrapHostSeverityFilter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapHostSeverityFilter 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.9
The minimum severity value an snmp trap must have in order to be forwarded to this host.
Status: current Access: read-create
OBJECT-TYPE    
  JuniTrapSeverity  

juniSnmpTrapHostPingTimeOut 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.10
The maximum ping time window that this host gets pinged repeatedly.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..90  

juniSnmpTrapHostIncludeLogVarbinds 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.11
The configuration setting for snmp trap message content. Enabling this management object configures the associated SNMP agent to include notification log name and the corresponding log index as part of the trap messages sent to this host.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniSnmpTrapHostQueueSize 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.12
The maximum number of traps to be kept in the queue.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 32..2147483647  

juniSnmpTrapHostQueueDrainRate 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.13
The maximum number of traps per second to be sent to the host. Zero value indicates that there is no control over queue drain rate.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

juniSnmpTrapHostQueueFull 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.14
Specify the method for handling Queue-Full condition. dropLastIn -- When queue is full the most recent trap will be dropped. dropFirstIn -- When queue is full the oldest trap in the queue will be dropped.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER dropLastIn(0), dropFirstIn(1)  

juniSnmpTrapHostBadEncodingDiscards 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.15
The number of trap requests that were discarded due to bad encoding.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapHostQueueFullDiscards 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.16
The number of trap requests that were discarded due to the queue being full.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapHostNoResponseDiscards 1.3.6.1.4.1.4874.2.2.16.1.3.3.1.17
The number of trap requests that were discarded due to host not being available (not responding to the pings).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapProxy 1.3.6.1.4.1.4874.2.2.16.1.3.4
The configuration setting for snmp trap proxying. Enabling this management object configures the associated SNMP agent to proxy internally generated traps. Note that some implementations may support a single snmp trap proxy per system.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniSnmpTrapTrapSeverity 1.3.6.1.4.1.4874.2.2.16.1.3.5
The severity level of the trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  JuniTrapSeverity  

juniSnmpTrapGlobalDiscards 1.3.6.1.4.1.4874.2.2.16.1.3.6
The number of trap requests that were discarded. A trap may be discarded because the trap type is either not globally configured in juniSnmpTrapGlobalFilter, or because the traps's priority is below the minimum trap severity filter defined by juniSnmpTrapGlobalSeverityFilter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapGlobalSeverityFilter 1.3.6.1.4.1.4874.2.2.16.1.3.7
Traps flow through two levels of filtering: global and then host. The value of this object defines the global minimum severity level a trap must have in order to be forwarded to the host level trap processing. A trap will be discarded and counted in juniSnmpTrapGlobalDiscards if its severity level is less then the value of this object.
Status: current Access: read-write
OBJECT-TYPE    
  JuniTrapSeverity  

juniSnmpTrapTotalTrapsReceived 1.3.6.1.4.1.4874.2.2.16.1.3.8
Total number of trap requests that this agent has received. Includes local submitted traps and proxied traps from other agents if this agent is the proxy agent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapLocalTrapsSubmitted 1.3.6.1.4.1.4874.2.2.16.1.3.9
The number of local traps submitted to this agent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapProxyTrapsSubmitted 1.3.6.1.4.1.4874.2.2.16.1.3.10
The number of proxied traps submitted to this agent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapTotalTrapsDiscarded 1.3.6.1.4.1.4874.2.2.16.1.3.11
The number of proxy traps submitted to this agent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapNoMemoryDiscards 1.3.6.1.4.1.4874.2.2.16.1.3.12
The number of trap requests that were discarded due to lack of system memory.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapNoQueueResourceDiscards 1.3.6.1.4.1.4874.2.2.16.1.3.13
The number of trap requests that were discarded due to no queue resources. A trap may be discarded because the agent request queue is full juniSnmpTrapRequestQueueCongestionDiscards or the proxy agent reuest queue is full juniSnmpTrapProxyRequestQueueCongestion.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapAgentSnmpNotAbleDiscards 1.3.6.1.4.1.4874.2.2.16.1.3.14
The number of trap requests that were discarded due to SNMP agent being disabled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapTotalTrapsOut 1.3.6.1.4.1.4874.2.2.16.1.3.15
Total number of trap requests sent to every host that is configured to receive traps from this agent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapTotalProxyOut 1.3.6.1.4.1.4874.2.2.16.1.3.16
Total number of trap requests sent to proxy virtual router.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniSnmpTrapSeverityFilterTable 1.3.6.1.4.1.4874.2.2.16.1.3.17
A table of SNMP trap Severity filter.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniSnmpTrapSeverityFilterEntry

juniSnmpTrapSeverityFilterEntry 1.3.6.1.4.1.4874.2.2.16.1.3.17.1
A table entry specifying the trap severity filter for a particular trap category.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniSnmpTrapSeverityFilterEntry  

juniSnmpTrapCategory 1.3.6.1.4.1.4874.2.2.16.1.3.17.1.1
The value of this object is an integer which is same as the bit position specified for a particular trap category in JuniSnmpTrapMask. For example, value of juniSnmpTrapCategory object will be 6 for BGP traps.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

juniSnmpTrapSeverityFilter 1.3.6.1.4.1.4874.2.2.16.1.3.17.1.2
Traps flow through two levels of filtering: severity of a particular trap category and trap destination. If the severity of a particular category is not defined, global trap severity is used for computation. The value of this object defines trap-category based minimum severity level, a trap must have in order to be forwarded for the destination level trap filtering. A trap will be discarded and counted in juniSnmpTrapGlobalDiscards if its severity level is less than the value of this object. For security reasons, 'Mirror' category will not be allowed to be configured through SNMP. Only those trap categories which are configured using per category based trap severity filter are displayed as part of this table. If the value of juniSnmpTrapGlobalSeverityFilter is modified, it will overwrite all the values specified in this table.
Status: current Access: read-write
OBJECT-TYPE    
  JuniTrapSeverity  

juniSnmpAuthFailIdIpAddress 1.3.6.1.4.1.4874.2.2.16.1.4.1
The source IP address contained in a received SNMP request that failed authentication.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

juniSnmpAuthFailIdUdpPort 1.3.6.1.4.1.4874.2.2.16.1.4.2
The source UDP port contained in a received SNMP request that failed authentication.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

juniSnmpAuthFailIdCommunity 1.3.6.1.4.1.4874.2.2.16.1.4.3
The SNMP community contained in a received SNMP request that failed authentication.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING  

juniSnmpAuthFailIdReason 1.3.6.1.4.1.4874.2.2.16.1.4.4
The reason a received SNMP request failed authentication: other Unspecified reason. badCommunityName The community is not recognized. badCommunityUse The community does not have privilege for the SNMP request type (e.g. SET request with a community having read-only privilege). hostDenied The host IP address was denied by the community's associated access list.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER other(0), badCommunityName(1), badCommmunityUse(2), hostDenied(3)  

juniSnmpCompliances 1.3.6.1.4.1.4874.2.2.16.2.1
OBJECT IDENTIFIER    

juniSnmpGroups 1.3.6.1.4.1.4874.2.2.16.2.2
OBJECT IDENTIFIER    

juniSnmpCompliance 1.3.6.1.4.1.4874.2.2.16.2.1.1
Obsolete compliance statement for entities which implement the Juniper SNMP MIB. This statement became obsolete when View support and Named Access List support were added.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpCompliance2 1.3.6.1.4.1.4874.2.2.16.2.1.2
Obsolete compliance statement for entities which implement the Juniper SNMP MIB. This statement became obsolete when juniSnmpInterfaceMode was added.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpCompliance3 1.3.6.1.4.1.4874.2.2.16.2.1.3
Obsolete compliance statement for entities which implement the Juniper SNMP MIB. This statement became obsolete when support for interface compress, trap severities and trap severity filtering was added and juniSnmpInterfaceMode was obsoleted.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpCompliance4 1.3.6.1.4.1.4874.2.2.16.2.1.4
Obsolete compliance statement for entities which implement the Juniper SNMP MIB. This statement became obsolete when trap proxy enable/disable support was added.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpCompliance5 1.3.6.1.4.1.4874.2.2.16.2.1.5
Obsolete compliance statement for entities which implement the Juniper SNMP MIB. This statement became obsolete when support was added for ping time window and notification log data inclusion in trap varbinds.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpCompliance6 1.3.6.1.4.1.4874.2.2.16.2.1.6
The compliance statement for entities which implement the Juniper SNMP MIB. This statement became obsolete when support was added for access permission and management application table.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpCompliance7 1.3.6.1.4.1.4874.2.2.16.2.1.7
The compliance statement for entities which implement the Juniper SNMP MIB. This statement became obsolete when support was added for trap severity filter table.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpCompliance8 1.3.6.1.4.1.4874.2.2.16.2.1.8
The compliance statement for entities which implement the Juniper SNMP MIB. This statement became obsolete when support was added for table type based interface compression.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpCompliance9 1.3.6.1.4.1.4874.2.2.16.2.1.9
The compliance statement for entities which implement the Juniper SNMP MIB.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

juniSnmpGroup 1.3.6.1.4.1.4874.2.2.16.2.2.1
Obsolete collection of management objects pertaining to SNMP Agent capability in a Juniper product. This group became obsolete when View support and Named Access List support were added.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpAuthFailGroup 1.3.6.1.4.1.4874.2.2.16.2.2.2
A collection of management objects pertaining to an SNMP authentication failure in a Juniper product.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpGroup2 1.3.6.1.4.1.4874.2.2.16.2.2.3
Obsolete collection of management objects pertaining to SNMP Agent capability in a Juniper product. This group became obsolete when juniSnmpInterfaceMode was added.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpGroup3 1.3.6.1.4.1.4874.2.2.16.2.2.4
Obsolete collection of management objects pertaining to SNMP Agent capability in a Juniper product. This group became obsolete when support for interface compress, trap severities and trap severity filtering was added and juniSnmpInterfaceMode was obsoleted.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpGeneralGroup 1.3.6.1.4.1.4874.2.2.16.2.2.5
Obsolete collection of management objects pertaining to general SNMP Agent capabilities in a Juniper product. This group became obsolete when proxy enable/disable support was added.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpAccessGroup 1.3.6.1.4.1.4874.2.2.16.2.2.6
A collection of management objects pertaining to SNMP Agent access capabilities in a Juniper product.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpTrapGroup 1.3.6.1.4.1.4874.2.2.16.2.2.7
Obsolete collection of management objects pertaining to SNMP Agent trap capabilities in a Juniper product. This group became obsolete when support was added for ping time window and notification log data inclusion in trap varbinds.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpGeneralGroup2 1.3.6.1.4.1.4874.2.2.16.2.2.8
A collection of management objects pertaining to general SNMP Agent capabilities in a Juniper product. This group became obsolete when access permission was added.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpTrapGroup2 1.3.6.1.4.1.4874.2.2.16.2.2.9
Obsolete collection of management objects pertaining to SNMP Agent trap capabilities in a Juniper product. This group became obsolete when support was added for trap severity filter table.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpGeneralGroup3 1.3.6.1.4.1.4874.2.2.16.2.2.10
A collection of management objects pertaining to general SNMP Agent capabilities in a Juniper product. This group became obsolete when support for interface compression based on interface table type was added.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpTrapGroup3 1.3.6.1.4.1.4874.2.2.16.2.2.11
A collection of management objects pertaining to SNMP Agent trap capabilities in a Juniper product.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

juniSnmpGeneralGroup4 1.3.6.1.4.1.4874.2.2.16.2.2.12
A collection of management objects pertaining to general SNMP Agent capabilities in a Juniper product.
Status: current Access: accessible-for-notify
OBJECT-GROUP