Juniper-REDUNDANCY-MIB

File: Juniper-REDUNDANCY-MIB.mib (22840 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-MIB
SNMPv2-CONF Juniper-MIBs

Imported symbols

NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
Integer32 TimeTicks DisplayString
RowStatus TruthValue TEXTUAL-CONVENTION
DateAndTime sysUpTime NOTIFICATION-GROUP
MODULE-COMPLIANCE OBJECT-GROUP juniMibs

Defined Types

JuniRedundancyState  
The current state of redundancy subsystem: notKnown - Redundancy state is unknown. fileSystemSyncing - Redundancy operation is based on file system synchronization. SRP switchover stops forwarding. disabled - Redundancy operation is based on high availability model but high availability is not yet operational. SRP switchover stops forwarding. initializing - Redundancy operation is based on high availability model and standby SRP is being bulk synchronized from active SRP. SRP switchover stops forwarding. pending - Redundancy operation is based on high availability model and bulk synchronization of standby SRP completed. SRP switchover stops forwarding. active - Redundancy operation is based on high availability model and high availability is fully operational. SRP switchover does not stop forwarding.
TEXTUAL-CONVENTION    
  INTEGER notKnown(1), fileSystemSyncing(2), disabled(3), initializing(4), pending(5), active(6)  

JuniRedundancyMode  
The mode of the redundancy subsystem: fileSystemSynchronization - SRP synchronization is based on file synchronization. highAvailability - SRP synchronization is based on high availability model that allows non-stop forwarding.
TEXTUAL-CONVENTION    
  INTEGER fileSystemSynchronization(1), highAvailability(2)  

JuniRedundancyResetReason  
Reason codes for the reset of active SRP or a line card that might result in switch of control to standby SRP or spare line card. none - No reset or switchover has occurred and indicates 'power-on' situation. notKnown - Reason is unknown. userInitiated - A safe, manual reset was initiated by the user.
TEXTUAL-CONVENTION    
  INTEGER none(1), notKnown(2), userInitiated(3)  

JuniRedundancySystemActivationType  
Various kinds of system activation: reload - System has reloaded, i.e., no switchover has occurred. coldSwitch - System switched over from active to standby SRP and the switchover involved reloading of line cards interrupting forwarding. warmSwitch - System switched over from active to standby SRP; line cards were not reloaded during switchover and forwarding was uninterrupted.
TEXTUAL-CONVENTION    
  INTEGER reload(1), coldSwitch(2), warmSwitch(3)  

JuniRedundancyResetType  
Identifies the nature of the reset and slot types involved since the system is powered on. notKnown - Reset type is unknown. srpReload - The reset involved reloading SRP slot(s). srpSwitchover - The reset involved switchover of SRP slot(s). linecardReload - The reset involved reloading the line card slot(s). linecardSwitchover - The reset involved line card redundancy.
TEXTUAL-CONVENTION    
  INTEGER notKnown(1), srpReload(2), srpSwitchover(3), linecardReload(4), linecardSwitchover(5)  

JuniRedundancyHistoryCommand  
Identifies the command to be performed on the system activation history table. keep - Retain history in persistent storage. clear - Erase the current entries of juniRedundancySystemActivationHistoryTable.
TEXTUAL-CONVENTION    
  INTEGER keep(1), clear(2)  

JuniRedundancySystemActivationHistoryEntry  
SEQUENCE    
  juniRedundancySystemActivationHistoryIndex Integer32
  juniRedundancyHistoryResetType JuniRedundancyResetType
  juniRedundancyHistoryActivationType JuniRedundancySystemActivationType
  juniRedundancyHistoryPrevActiveSlot Integer32
  juniRedundancyHistoryPrevActiveRelease DisplayString
  juniRedundancyHistoryCurrActiveSlot Integer32
  juniRedundancyHistoryCurrActiveRelease DisplayString
  juniRedundancyHistoryResetReason JuniRedundancyResetReason
  juniRedundancyHistoryActivationTime DateAndTime

Defined Values

juniRedundancyMIB 1.3.6.1.4.1.4874.2.2.74
The redundancy configuration MIB for Juniper Networks enterprise.
MODULE-IDENTITY    

juniRedundancyNotifications 1.3.6.1.4.1.4874.2.2.74.0
OBJECT IDENTIFIER    

juniRedundancyObjects 1.3.6.1.4.1.4874.2.2.74.1
OBJECT IDENTIFIER    

juniRedundancyMIBConformance 1.3.6.1.4.1.4874.2.2.74.2
OBJECT IDENTIFIER    

juniRedundancyStatus 1.3.6.1.4.1.4874.2.2.74.1.1
OBJECT IDENTIFIER    

juniRedundancyCfg 1.3.6.1.4.1.4874.2.2.74.1.2
OBJECT IDENTIFIER    

juniRedundancyHistory 1.3.6.1.4.1.4874.2.2.74.1.3
OBJECT IDENTIFIER    

juniRedundancyActiveSlot 1.3.6.1.4.1.4874.2.2.74.1.1.1
A unique identifier for active SRP slot.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

juniRedundancyActiveSlotState 1.3.6.1.4.1.4874.2.2.74.1.1.2
The current state of redundancy on active SRP.
Status: current Access: read-only
OBJECT-TYPE    
  JuniRedundancyState  

juniRedundancyStandbySlot 1.3.6.1.4.1.4874.2.2.74.1.1.3
A unique identifier for standby SRP slot.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

juniRedundancyStandbySlotState 1.3.6.1.4.1.4874.2.2.74.1.1.4
The current state of redundancy on standby SRP.
Status: current Access: read-only
OBJECT-TYPE    
  JuniRedundancyState  

juniRedundancyLastResetReason 1.3.6.1.4.1.4874.2.2.74.1.1.5
The reason for the last SRP reset.
Status: current Access: read-only
OBJECT-TYPE    
  JuniRedundancyResetReason  

juniRedundancyLastSystemActivationTime 1.3.6.1.4.1.4874.2.2.74.1.1.6
The value of sysUptime when the system is operational either following a reload or a switchover. The value 0 is a special value to indicate 'from reset'.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

juniRedundancyLastSystemActivationType 1.3.6.1.4.1.4874.2.2.74.1.1.7
The type of last SRP activation when the system became operational.
Status: current Access: read-only
OBJECT-TYPE    
  JuniRedundancySystemActivationType  

juniRedundancyHaActiveTime 1.3.6.1.4.1.4874.2.2.74.1.1.8
The value of sysUptime when active SRP enters 'active' state as indicated in juniRedundancyActiveSlotState object. The value is 0 in file system synchronization redundancy mode.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

juniRedundancyNotifsEnabled 1.3.6.1.4.1.4874.2.2.74.1.2.1
Allows enabling and disabling of redundancy subsystem notifications.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniRedundancyCfgRedundancyMode 1.3.6.1.4.1.4874.2.2.74.1.2.2
Indicates the redundancy mode configured on the system.
Status: current Access: read-write
OBJECT-TYPE    
  JuniRedundancyMode  

juniRedundancySystemActivationHistoryTableMaxLength 1.3.6.1.4.1.4874.2.2.74.1.3.1
Maximum number of entries allowed in juniRedundancySystemActivationHistoryTable. A value of 0 will result in no history being displayed in juniRedundancySystemActivationHistoryTable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..50  

juniRedundancySystemActivationHistoryCommand 1.3.6.1.4.1.4874.2.2.74.1.3.2
A control variable to perform certain operations on juniRedundancySystemActivationHistoryTable.
Status: current Access: read-write
OBJECT-TYPE    
  JuniRedundancyHistoryCommand  

juniRedundancySystemActivationHistoryTable 1.3.6.1.4.1.4874.2.2.74.1.3.3
A table that tracks the history of all reloads and switchovers that have occurred since system is powered on. The maximum number of entries permissible in this table is defined by juniRedundancySystemActivationHistoryTableMaxLength. When the number of entries in the table reaches the maximum limit, the next entry would replace the oldest existing entry in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniRedundancySystemActivationHistoryEntry

juniRedundancySystemActivationHistoryEntry 1.3.6.1.4.1.4874.2.2.74.1.3.3.1
The entries in this table contain the reload and switchover information. Each entry in the table is indexed by juniRedundancySystemActivationHistoryIndex. The index wraps around to 1 after reaching the maximum value.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniRedundancySystemActivationHistoryEntry  

juniRedundancySystemActivationHistoryIndex 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.1
An integer value for the purpose of indexing system activation history table. After reaching maximum value as indicated by juniRedundancySystemActivationHistoryTableMaxLength, it wraps around to 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

juniRedundancyHistoryResetType 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.2
Indicates the nature of the reset - reload or switchover - and the slot types involved. Depending on the value of this object, certain elements of JuniRedundancySystemActivationHistoryEntry will not be applicable.
Status: current Access: read-only
OBJECT-TYPE    
  JuniRedundancyResetType  

juniRedundancyHistoryActivationType 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.3
Indicates the activation type of the particular historical system activation entry with respect to the slot types involved.
Status: current Access: read-only
OBJECT-TYPE    
  JuniRedundancySystemActivationType  

juniRedundancyHistoryPrevActiveSlot 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.4
Indicates the slot number of active SRP or line card that went down.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

juniRedundancyHistoryPrevActiveRelease 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.5
Indicates the system-wide boot release file name of the slot indicated by juniRedundancyHistoryPrevActiveSlot.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniRedundancyHistoryCurrActiveSlot 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.6
Indicates the slot number of standby SRP or spare line card that took over.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

juniRedundancyHistoryCurrActiveRelease 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.7
Indicates the system-wide boot release file name of the slot indicated by juniRedundancyHistoryCurrActiveSlot.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniRedundancyHistoryResetReason 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.8
Indicates the reason for reload or switchover of the slots involved.
Status: current Access: read-only
OBJECT-TYPE    
  JuniRedundancyResetReason  

juniRedundancyHistoryActivationTime 1.3.6.1.4.1.4874.2.2.74.1.3.3.1.9
Indicates the date and time when the reload or switchover of the slots occurred.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

juniRedundancyHistoryReloads 1.3.6.1.4.1.4874.2.2.74.1.3.4
Indicates the number of reloads since the system is powered on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

juniRedundancyHistoryColdSwitchovers 1.3.6.1.4.1.4874.2.2.74.1.3.5
Indicates the number of cold switchovers since the system is powered on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

juniRedundancyHistoryWarmSwitchovers 1.3.6.1.4.1.4874.2.2.74.1.3.6
Indicates the number of warm switchovers since the system is powered on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

juniRedundancyColdSwitchoverNotification 1.3.6.1.4.1.4874.2.2.74.0.1
This notification is generated in a dual SRP system when control transfers from one to SRP to the other in file system synchronization mode or when high availability is not operational. This notification is sent by the newly active SRP immediately following the switchover in which configuration is preserved but volatile state is lost.
Status: current Access: read-only
NOTIFICATION-TYPE    

juniRedundancyWarmSwitchoverNotification 1.3.6.1.4.1.4874.2.2.74.0.2
This notification is generated in a dual SRP system when control transfers from one SRP to the other and high availability is operational. This notification is sent by the newly active SRP immediately following the switchover in which configuration and volatile state are preserved.
Status: current Access: read-only
NOTIFICATION-TYPE    

juniRedundancyStateEnabledNotification 1.3.6.1.4.1.4874.2.2.74.0.3
A state change notification sent by active SRP whenever system enters 'active' state.
Status: current Access: read-only
NOTIFICATION-TYPE    

juniRedundancyStateDisabledNotification 1.3.6.1.4.1.4874.2.2.74.0.4
A state change notification sent by active SRP whenever system enters 'disabled' state.
Status: current Access: read-only
NOTIFICATION-TYPE    

juniRedundancyStatePendingNotification 1.3.6.1.4.1.4874.2.2.74.0.5
A state change notification sent by active SRP whenever system enters 'pending' state.
Status: current Access: read-only
NOTIFICATION-TYPE    

juniRedundancyModeNotification 1.3.6.1.4.1.4874.2.2.74.0.6
A mode change notification sent by active SRP whenever redundancy mode of the system is changed from 'fileSystemSynchronization' to 'highAvailability' and vice versa.
Status: current Access: read-only
NOTIFICATION-TYPE    

juniRedundancyMIBCompliances 1.3.6.1.4.1.4874.2.2.74.2.1
OBJECT IDENTIFIER    

juniRedundancyMIBGroups 1.3.6.1.4.1.4874.2.2.74.2.2
OBJECT IDENTIFIER    

juniRedundancyMIBCompliance 1.3.6.1.4.1.4874.2.2.74.2.1.1
The compliance statement for system redundancy support.
Status: current Access: read-only
MODULE-COMPLIANCE    

juniRedundancyStatusGroup 1.3.6.1.4.1.4874.2.2.74.2.2.1
The collection of redundancy status objects.
Status: current Access: read-only
OBJECT-GROUP    

juniRedundancyCfgGroup 1.3.6.1.4.1.4874.2.2.74.2.2.2
The collection of redundancy configuration objects.
Status: current Access: read-only
OBJECT-GROUP    

juniRedundancyHistoryGroup 1.3.6.1.4.1.4874.2.2.74.2.2.3
The collection of redundancy history objects.
Status: current Access: read-only
OBJECT-GROUP    

juniRedundancyNotificationGroup 1.3.6.1.4.1.4874.2.2.74.2.2.4
The collection of notifications for redundancy events.
Status: current Access: read-only
NOTIFICATION-GROUP