| JnxSoamTcDelayMeasurementBinType |
|
| This enumeration data type is used to distinguish between
measurement bins for Frame Delay, Frame Delay Range, and
Inter-frame Delay variation.
The valid enumerated values associated with this type are:
twoWayFrameDelay(1) indicates a measurement bin for two-way
Frame Delay.
forwardFrameDelay(2) indicates a measurement bin for one-way
Frame Delay in the forward direction.
backwardFrameDelay(3) indicates a measurement bin for one-way
Frame Delay in the backward direction.
twoWayIfdv(4) indicates a measurement bin for two-way
Inter-frame Delay Variation.
forwardIfdv(5) indicates a measurement bin for one-way
Inter-frame Delay Variation in the forward
direction.
backwardIfdv(6) indicates a measurement bin for one-way
Inter-frame Delay Variation in the backward
direction.
twoWayFrameDelayRange(7) indicates a measurement bin for two-way
Frame Delay Range.
forwardFrameDelayRange(8) indicates a measurement bin for one-way
Frame Delay Range in the forward direction.
backwardFrameDelayRange(9) indicates a measurement bin for one-way
Frame Delay Range in the backward direction.
|
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
twoWayFrameDelay(1), forwardFrameDelay(2), backwardFrameDelay(3), twoWayIfdv(4), forwardIfdv(5), backwardIfdv(6), twoWayFrameDelayRange(7), forwardFrameDelayRange(8), backwardFrameDelayRange(9) |
|
| JnxSoamPmMepEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamPmMepOperNextIndex |
Dot1afCfmIndexIntegerNextFree |
|
| |
jnxSoamPmMepLmSingleEndedResponder |
TruthValue |
|
| |
jnxSoamPmMepSlmSingleEndedResponder |
TruthValue |
|
| |
jnxSoamPmMepDmSingleEndedResponder |
TruthValue |
|
| JnxSoamLmCfgEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamLmCfgIndex |
Unsigned32 |
|
| |
jnxSoamLmCfgType |
INTEGER |
|
| |
jnxSoamLmCfgVersion |
Unsigned32 |
|
| |
jnxSoamLmCfgEnabled |
TruthValue |
|
| |
jnxSoamLmCfgMeasurementEnable |
BITS |
|
| |
jnxSoamLmCfgMessagePeriod |
Integer32 |
|
| |
jnxSoamLmCfgPriority |
IEEE8021PriorityValue |
|
| |
jnxSoamLmCfgFrameSize |
Unsigned32 |
|
| |
jnxSoamLmCfgDataPattern |
JnxSoamTcDataPatternType |
|
| |
jnxSoamLmCfgTestTlvIncluded |
TruthValue |
|
| |
jnxSoamLmCfgTestTlvPattern |
JnxSoamTcTestPatternType |
|
| |
jnxSoamLmCfgNumIntervalsStored |
Unsigned32 |
|
| |
jnxSoamLmCfgDestMepId |
Dot1agCfmMepIdOrZero |
|
| |
jnxSoamLmCfgDestIsMepId |
TruthValue |
|
| |
jnxSoamLmCfgStartTimeType |
JnxSoamTcOperationTimeType |
|
| |
jnxSoamLmCfgFixedStartDateAndTime |
DateAndTime |
|
| |
jnxSoamLmCfgRelativeStartTime |
TimeInterval |
|
| |
jnxSoamLmCfgRepetitionTime |
Unsigned32 |
|
| |
jnxSoamLmCfgAlignMeasurementIntervals |
TruthValue |
|
| |
jnxSoamLmCfgAlignMeasurementOffset |
Unsigned32 |
|
| |
jnxSoamLmCfgSessionType |
OCTET STRING |
|
| |
jnxSoamLmCfgSessionStatus |
OCTET STRING |
|
| |
jnxSoamLmCfgHistoryClear |
TruthValue |
|
| |
jnxSoamLmCfgRowStatus |
RowStatus |
|
| |
jnxSoamLmCfgMeasurementInterval |
Unsigned32 |
|
| |
jnxSoamLmCfgDestMacAddress |
MacAddress |
|
| |
jnxSoamLmCfgStopTimeType |
JnxSoamTcOperationTimeType |
|
| |
jnxSoamLmCfgFixedStopDateAndTime |
DateAndTime |
|
| |
jnxSoamLmCfgRelativeStopTime |
TimeInterval |
|
| |
jnxSoamLmCfgAvailabilityMeasurementInterval |
Unsigned32 |
|
| |
jnxSoamLmCfgAvailabilityNumConsecutiveMeasPdus |
Unsigned32 |
|
| |
jnxSoamLmCfgAvailabilityFlrThreshold |
Unsigned32 |
|
| |
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals |
Unsigned32 |
|
| |
jnxSoamLmCfgAvailabilityNumConsecutiveHighFlr |
Unsigned32 |
|
| JnxSoamLmMeasuredStatsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamLmMeasuredStatsForwardFlr |
Unsigned32 |
|
| |
jnxSoamLmMeasuredStatsBackwardFlr |
Unsigned32 |
|
| |
jnxSoamLmMeasuredStatsAvailForwardStatus |
JnxSoamTcAvailabilityType |
|
| |
jnxSoamLmMeasuredStatsAvailBackwardStatus |
JnxSoamTcAvailabilityType |
|
| |
jnxSoamLmMeasuredStatsAvailForwardLastTransitionTime |
DateAndTime |
|
| |
jnxSoamLmMeasuredStatsAvailBackwardLastTransitionTime |
DateAndTime |
|
| JnxSoamLmCurrentStatsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamLmCurrentStatsIndex |
Unsigned32 |
|
| |
jnxSoamLmCurrentStatsStartTime |
DateAndTime |
|
| |
jnxSoamLmCurrentStatsElapsedTime |
TimeInterval |
|
| |
jnxSoamLmCurrentStatsSuspect |
TruthValue |
|
| |
jnxSoamLmCurrentStatsForwardTransmittedFrames |
Gauge32 |
|
| |
jnxSoamLmCurrentStatsForwardReceivedFrames |
Gauge32 |
|
| |
jnxSoamLmCurrentStatsForwardMinFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentStatsForwardMaxFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentStatsForwardAvgFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentStatsBackwardTransmittedFrames |
Gauge32 |
|
| |
jnxSoamLmCurrentStatsBackwardReceivedFrames |
Gauge32 |
|
| |
jnxSoamLmCurrentStatsBackwardMinFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentStatsBackwardMaxFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentStatsBackwardAvgFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentStatsSoamPdusSent |
Gauge32 |
|
| |
jnxSoamLmCurrentStatsSoamPdusReceived |
Gauge32 |
|
| JnxSoamLmHistoryStatsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamLmHistoryStatsIndex |
Unsigned32 |
|
| |
jnxSoamLmHistoryStatsEndTime |
DateAndTime |
|
| |
jnxSoamLmHistoryStatsElapsedTime |
TimeInterval |
|
| |
jnxSoamLmHistoryStatsSuspect |
TruthValue |
|
| |
jnxSoamLmHistoryStatsForwardTransmittedFrames |
Gauge32 |
|
| |
jnxSoamLmHistoryStatsForwardReceivedFrames |
Gauge32 |
|
| |
jnxSoamLmHistoryStatsForwardMinFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryStatsForwardMaxFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryStatsForwardAvgFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryStatsBackwardTransmittedFrames |
Gauge32 |
|
| |
jnxSoamLmHistoryStatsBackwardReceivedFrames |
Gauge32 |
|
| |
jnxSoamLmHistoryStatsBackwardMinFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryStatsBackwardMaxFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryStatsBackwardAvgFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryStatsSoamPdusSent |
Gauge32 |
|
| |
jnxSoamLmHistoryStatsSoamPdusReceived |
Gauge32 |
|
| JnxSoamDmCfgEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamDmCfgIndex |
Unsigned32 |
|
| |
jnxSoamDmCfgType |
INTEGER |
|
| |
jnxSoamDmCfgVersion |
Unsigned32 |
|
| |
jnxSoamDmCfgEnabled |
TruthValue |
|
| |
jnxSoamDmCfgMeasurementEnable |
BITS |
|
| |
jnxSoamDmCfgMessagePeriod |
Integer32 |
|
| |
jnxSoamDmCfgPriority |
IEEE8021PriorityValue |
|
| |
jnxSoamDmCfgFrameSize |
Unsigned32 |
|
| |
jnxSoamDmCfgDataPattern |
JnxSoamTcDataPatternType |
|
| |
jnxSoamDmCfgTestTlvIncluded |
TruthValue |
|
| |
jnxSoamDmCfgTestTlvPattern |
JnxSoamTcTestPatternType |
|
| |
jnxSoamDmCfgNumIntervalsStored |
Unsigned32 |
|
| |
jnxSoamDmCfgDestMepId |
Dot1agCfmMepIdOrZero |
|
| |
jnxSoamDmCfgDestIsMepId |
TruthValue |
|
| |
jnxSoamDmCfgStartTimeType |
JnxSoamTcOperationTimeType |
|
| |
jnxSoamDmCfgRepetitionTime |
Unsigned32 |
|
| |
jnxSoamDmCfgAlignMeasurementIntervals |
TruthValue |
|
| |
jnxSoamDmCfgInterFrameDelayVariationSelectionOffset |
Unsigned32 |
|
| |
jnxSoamDmCfgSessionType |
OCTET STRING |
|
| |
jnxSoamDmCfgSessionStatus |
OCTET STRING |
|
| |
jnxSoamDmCfgHistoryClear |
TruthValue |
|
| |
jnxSoamDmCfgRowStatus |
RowStatus |
|
| |
jnxSoamDmCfgMeasurementInterval |
Unsigned32 |
|
| |
jnxSoamDmCfgDestMacAddress |
MacAddress |
|
| |
jnxSoamDmCfgSourceMacAddress |
MacAddress |
|
| |
jnxSoamDmCfgFixedStartDateAndTime |
DateAndTime |
|
| |
jnxSoamDmCfgRelativeStartTime |
TimeInterval |
|
| |
jnxSoamDmCfgStopTimeType |
JnxSoamTcOperationTimeType |
|
| |
jnxSoamDmCfgFixedStopDateAndTime |
DateAndTime |
|
| |
jnxSoamDmCfgRelativeStopTime |
TimeInterval |
|
| |
jnxSoamDmCfgAlignMeasurementOffset |
Unsigned32 |
|
| |
jnxSoamDmCfgNumMeasBinsPerFrameDelayInterval |
Unsigned32 |
|
| |
jnxSoamDmCfgNumMeasBinsPerInterFrameDelayVariationInterval |
Unsigned32 |
|
| |
jnxSoamDmCfgNumMeasBinsPerFrameDelayRangeInterval |
Unsigned32 |
|
| JnxSoamDmMeasuredStatsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamDmMeasuredStatsFrameDelayTwoWay |
Unsigned32 |
|
| |
jnxSoamDmMeasuredStatsFrameDelayForward |
Unsigned32 |
|
| |
jnxSoamDmMeasuredStatsFrameDelayBackward |
Unsigned32 |
|
| |
jnxSoamDmMeasuredStatsIfdvTwoWay |
Unsigned32 |
|
| |
jnxSoamDmMeasuredStatsIfdvForward |
Unsigned32 |
|
| |
jnxSoamDmMeasuredStatsIfdvBackward |
Unsigned32 |
|
| JnxSoamDmCurrentStatsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamDmCurrentStatsIndex |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsStartTime |
DateAndTime |
|
| |
jnxSoamDmCurrentStatsElapsedTime |
TimeInterval |
|
| |
jnxSoamDmCurrentStatsSuspect |
TruthValue |
|
| |
jnxSoamDmCurrentStatsFrameDelayTwoWayMin |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayTwoWayMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayTwoWayAvg |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayForwardMin |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayForwardMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayForwardAvg |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayBackwardMin |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayBackwardMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayBackwardAvg |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvForwardMin |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvForwardMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvForwardAvg |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvBackwardMin |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvBackwardMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvBackwardAvg |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvTwoWayMin |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvTwoWayMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsIfdvTwoWayAvg |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsSoamPdusSent |
Gauge32 |
|
| |
jnxSoamDmCurrentStatsSoamPdusReceived |
Gauge32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayRangeForwardMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax |
Unsigned32 |
|
| |
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg |
Unsigned32 |
|
| JnxSoamDmHistoryStatsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamDmHistoryStatsIndex |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsEndTime |
DateAndTime |
|
| |
jnxSoamDmHistoryStatsElapsedTime |
TimeInterval |
|
| |
jnxSoamDmHistoryStatsSuspect |
TruthValue |
|
| |
jnxSoamDmHistoryStatsFrameDelayTwoWayMin |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayTwoWayMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayTwoWayAvg |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayForwardMin |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayForwardMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayForwardAvg |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayBackwardMin |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayBackwardMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayBackwardAvg |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvForwardMin |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvForwardMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvForwardAvg |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvBackwardMin |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvBackwardMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvBackwardAvg |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvTwoWayMin |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvTwoWayMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsIfdvTwoWayAvg |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsSoamPdusSent |
Gauge32 |
|
| |
jnxSoamDmHistoryStatsSoamPdusReceived |
Gauge32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayRangeForwardMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayRangeForwardAvg |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayRangeBackwardMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvg |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMax |
Unsigned32 |
|
| |
jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvg |
Unsigned32 |
|
| JnxSoamLmThresholdCfgEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamLmThresholdCfgIndex |
Unsigned32 |
|
| |
jnxSoamLmThresholdCfgEnable |
BITS |
|
| |
jnxSoamLmThresholdCfgAvgFlrForwardThreshold |
Unsigned32 |
|
| |
jnxSoamLmThresholdCfgAvgFlrBackwardThreshold |
Unsigned32 |
|
| |
jnxSoamLmThresholdCfgRowStatus |
RowStatus |
|
| JnxSoamLmCurrentAvailStatsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamLmCurrentAvailStatsIndex |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsStartTime |
DateAndTime |
|
| |
jnxSoamLmCurrentAvailStatsElapsedTime |
TimeInterval |
|
| |
jnxSoamLmCurrentAvailStatsSuspect |
TruthValue |
|
| |
jnxSoamLmCurrentAvailStatsForwardHighLoss |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsBackwardHighLoss |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsForwardConsecutiveHighLoss |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsForwardAvailable |
Gauge32 |
|
| |
jnxSoamLmCurrentAvailStatsBackwardAvailable |
Gauge32 |
|
| |
jnxSoamLmCurrentAvailStatsForwardUnavailable |
Gauge32 |
|
| |
jnxSoamLmCurrentAvailStatsBackwardUnavailable |
Gauge32 |
|
| |
jnxSoamLmCurrentAvailStatsForwardMinFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsForwardMaxFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsForwardAvgFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsBackwardMinFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsBackwardMaxFlr |
Unsigned32 |
|
| |
jnxSoamLmCurrentAvailStatsBackwardAvgFlr |
Unsigned32 |
|
| JnxSoamLmHistoryAvailStatsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamLmHistoryAvailStatsIndex |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsEndTime |
DateAndTime |
|
| |
jnxSoamLmHistoryAvailStatsElapsedTime |
TimeInterval |
|
| |
jnxSoamLmHistoryAvailStatsSuspect |
TruthValue |
|
| |
jnxSoamLmHistoryAvailStatsForwardHighLoss |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsBackwardHighLoss |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLoss |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsForwardAvailable |
Gauge32 |
|
| |
jnxSoamLmHistoryAvailStatsBackwardAvailable |
Gauge32 |
|
| |
jnxSoamLmHistoryAvailStatsForwardUnavailable |
Gauge32 |
|
| |
jnxSoamLmHistoryAvailStatsBackwardUnavailable |
Gauge32 |
|
| |
jnxSoamLmHistoryAvailStatsForwardMinFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsForwardMaxFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsForwardAvgFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsBackwardMinFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsBackwardMaxFlr |
Unsigned32 |
|
| |
jnxSoamLmHistoryAvailStatsBackwardAvgFlr |
Unsigned32 |
|
| JnxSoamDmThresholdCfgEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamDmThresholdCfgIndex |
Unsigned32 |
|
| |
jnxSoamDmThresholdCfgEnable |
BITS |
|
| |
jnxSoamDmThresholdCfgAvgFrameDelayTwoWayThreshold |
Unsigned32 |
|
| |
jnxSoamDmThresholdCfgAvgIfdvTwoWayThreshold |
Unsigned32 |
|
| |
jnxSoamDmThresholdCfgRowStatus |
RowStatus |
|
| JnxSoamDmCfgMeasBinEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamDmCfgMeasBinType |
JnxSoamTcDelayMeasurementBinType |
|
| |
jnxSoamDmCfgMeasBinNumber |
Unsigned32 |
|
| |
jnxSoamDmCfgMeasBinLowerBound |
Unsigned32 |
|
| JnxSoamDmCurrentStatsBinsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamDmCurrentStatsBinsCounter |
Gauge32 |
|
| JnxSoamDmHistoryStatsBinsEntry |
|
| SEQUENCE |
|
|
|
| |
jnxSoamDmHistoryStatsBinsCounter |
Gauge32 |
|
| jnxSoamPmMepEntry |
1.3.6.1.4.1.2636.3.78.1.1.1.1 |
| The conceptual row of jnxSoamPmMepTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamPmMepEntry |
|
|
| jnxSoamLmCfgEntry |
1.3.6.1.4.1.2636.3.78.1.2.1.1 |
| The conceptual row of jnxSoamLmCfgTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamLmCfgEntry |
|
|
| jnxSoamLmCfgMeasurementEnable |
1.3.6.1.4.1.2636.3.78.1.2.1.1.5 |
| A vector of bits that indicates the type of SOAM LM counters found
in the jnxSoamLmMeasuredStatsTable, jnxSoamLmCurrentStatsTable,
jnxSoamLmHistoryStatsTable that are enabled.
that are enabled.
A bit set to '1' enables the specific SOAM LM counter. A bit set to
'0' disables the SOAM LM counter.
If a particular SOAM LM counter is not supported the BIT value is
set to '0'.
Not all SOAM LM counters are supported for all SOAM LM types.
This object can only be written at row creation time and cannot be
modified once it has been created.
bForwardTransmitedFrames (0)
Enables/disables the jnxSoamLmCurrentStatsForwardTransmittedFrames
and jnxSoamLmHistoryStatsForwardTransmittedFrames counters.
bForwardReceivedFrames(1)
Enables/disables the jnxSoamLmCurrentStatsForwardReceivedFrames
and jnxSoamLmHistoryStatsForwardReceivedFrames counters.
bForwardMinFlr(2)
Enables/disables the jnxSoamLmCurrentStatsForwardMinFlr
and jnxSoamLmHistoryStatsForwardMinFlr counters.
bForwardMaxFlr(3)
Enables/disables the jnxSoamLmCurrentStatsForwardMaxFlr
and jnxSoamLmHistoryStatsForwardMaxFlr counters.
bForwardAvgFlr(4)
Enables/disables the jnxSoamLmCurrentStatsForwardAvgFlr
and jnxSoamLmHistoryStatsForwardAvgFlr counters.
bBackwardTransmitedFrames(5)
Enables/disables the jnxSoamLmCurrentStatsBackwardTransmittedFrames
and jnxSoamLmHistoryStatsBackwardTransmittedFrames counters.
bBackwardReceivedFrames(6)
Enables/disables the jnxSoamLmCurrentStatsBackwardReceivedFrames
and jnxSoamLmHistoryStatsBackwardReceivedFrames counters.
bBackwardMinFlr(7)
Enables/disables the jnxSoamLmCurrentStatsBackwardMinFlr
and jnxSoamLmHistoryStatsBackwardMinFlr counters.
bBackwardMaxFlr(8)
Enables/disables the jnxSoamLmCurrentStatsBackwardMaxFlr
and jnxSoamLmHistoryStatsBackwardMaxFlr counters.
bBackwardAvgFlr(9)
Enables/disables the jnxSoamLmCurrentStatsBackwardAvgFlr
and jnxSoamLmHistoryStatsBackwardAvgFlr counters.
bSoamPdusSent (10)
Enables/disables the jnxSoamLmCurrentStatsSoamPdusSent
and jnxSoamLmHistoryStatsSoamPdusSent counters.
bSoamPdusReceivedbReceivedMeasurements (11)
Enables/disables the jnxSoamLmCurrentStatsSoamPdusReceived
and jnxSoamLmHistoryStatsSoamPdusReceived counters.
bAvailForwardHighLoss(12)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardHighLoss
and jnxSoamLmHistoryAvailStatsForwardHighLoss counters.
bAvailForwardConsecutiveHighLoss(13)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardConsecutiveHighLoss
and jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLoss counters.
bAvailForwardAvailable(14)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardAvailable
and jnxSoamLmHistoryAvailStatsForwardAvailable counters.
bAvailForwardUnavailable(15)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardUnavailable
and jnxSoamLmHistoryAvailStatsForwardUnavailable counters.
bAvailForwardMinFlr(16)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardMinFlr
and jnxSoamLmHistoryAvailStatsForwardMinFlr counters.
bAvailForwardMaxFlr(17)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardMaxFlr
and jnxSoamLmHistoryAvailStatsForwardMaxFlr counters.
bAvailForwardAvgFlr(18)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardAvgFlr
and jnxSoamLmHistoryAvailStatsForwardAvgFlr counters.
bAvailBackwardHighLoss(19)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardHighLoss
and jnxSoamLmHistoryAvailStatsBackwardHighLoss counters.
bAvailBackwardConsecutiveHighLoss(20)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss
and jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss counters.
bAvailBackwardAvailable(21)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardAvailable
and jnxSoamLmHistoryAvailStatsBackwardAvailable counters.
bAvailBackwardUnavailable(22)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardUnavailable
and jnxSoamLmHistoryAvailStatsBackwardUnavailable counters.
bAvailBackwardMinFlr(23)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardMinFlr
and jnxSoamLmHistoryAvailStatsBackwardMinFlr counters.
bAvailBackwardMaxFlr(24)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardMaxFlr
and jnxSoamLmHistoryAvailStatsBackwardMaxFlr counters.
bAvailBackwardAvgFlr(25)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardAvgFlr
and jnxSoamLmHistoryAvailStatsBackwardAvgFlr counters.
Enables/disables the jnxSoamLmCurrentStatsSoamPdusReceived
and jnxSoamLmHistoryStatsSoamPdusReceived counters.
bMeasuredStatsForwardMeasuredFlr(26)
Enables/disables the jnxSoamLmMeasuredStatsForwardFlr counter.
bMeasuredStatsBackwardMeasuredFlr(27)
Enables/disables the jnxSoamLmMeasuredStatsBackwardFlr counter.
bMeasuredStatsAvailForwardStatus(28)
Enables/disables the jnxSoamLmMeasuredStatsAvailForwardStatus counter.
bMeasuredStatsAvailBackwardStatus(29)
Enables/disables the jnxSoamLmMeasuredStatsAvailBackwardStatus counter.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BITS |
bForwardTransmitedFrames(0), bForwardReceivedFrames(1), bForwardMinFlr(2), bForwardMaxFlr(3), bForwardAvgFlr(4), bBackwardTransmitedFrames(5), bBackwardReceivedFrames(6), bBackwardMinFlr(7), bBackwardMaxFlr(8), bBackwardAvgFlr(9), bSoamPdusSent(10), bSoamPdusReceived(11), bAvailForwardHighLoss(12), bAvailForwardConsecutiveHighLoss(13), bAvailForwardAvailable(14), bAvailForwardUnavailable(15), bAvailForwardMinFlr(16), bAvailForwardMaxFlr(17), bAvailForwardAvgFlr(18), bAvailBackwardHighLoss(19), bAvailBackwardConsecutiveHighLoss(20), bAvailBackwardAvailable(21), bAvailBackwardUnavailable(22), bAvailBackwardMinFlr(23), bAvailBackwardMaxFlr(24), bAvailBackwardAvgFlr(25), bMeasuredStatsForwardMeasuredFlr(26), bMeasuredStatsBackwardMeasuredFlr(27), bMeasuredStatsAvailForwardStatus(28), bMeasuredStatsAvailBackwardStatus(29) |
|
| jnxSoamLmCfgHistoryClear |
1.3.6.1.4.1.2636.3.78.1.2.1.1.23 |
| This object when written clears the Loss Measurement history
Table (jnxSoamLmHistoryStatsTable) - all rows are deleted.
When read the value always returns 'false'.
Writing this value does not change the current stat table,
nor any of the items in the configuration table.
Writing this value during row creation has no effect.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| jnxSoamLmMeasuredStatsEntry |
1.3.6.1.4.1.2636.3.78.1.2.2.1 |
| The conceptual row of jnxSoamLmMeasuredStatsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamLmMeasuredStatsEntry |
|
|
| jnxSoamLmCurrentStatsEntry |
1.3.6.1.4.1.2636.3.78.1.2.3.1 |
| The conceptual row of jnxSoamLmCurrentStatsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamLmCurrentStatsEntry |
|
|
| jnxSoamLmHistoryStatsTable |
1.3.6.1.4.1.2636.3.78.1.2.4 |
| This table contains the results for history Measurement
Intervals in a SOAM Loss Measurement session.
Rows of this table object are created automatically
by the SNMP Agent when the Loss Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the history statistics for a Loss
Measurement session Measurement Interval for the defined MEP. This
table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific LM session on the selected MEP. The fifth index index the
specific Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval may be deleted (row deletion). If the measurement
interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
Except for jnxSoamLmHistoryStatsIndex, jnxSoamLmHistoryStatsEndTime,
jnxSoamLmHistoryStatsElapsedTime and jnxSoamLmHistoryStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamLmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
JnxSoamLmHistoryStatsEntry |
|
| jnxSoamLmHistoryStatsEntry |
1.3.6.1.4.1.2636.3.78.1.2.4.1 |
| The conceptual row of jnxSoamLmHistoryStatsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamLmHistoryStatsEntry |
|
|
| jnxSoamLmHistoryStatsIndex |
1.3.6.1.4.1.2636.3.78.1.2.4.1.1 |
| The index for the Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1. Measurement Intervals
for FLR (stored in this table) are based on
iterator count and are indexed independently
of Measurement Intervals for availability
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamLmHistoryStatsEndTime |
1.3.6.1.4.1.2636.3.78.1.2.4.1.2 |
| The time that the Measurement Interval ended.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| jnxSoamLmHistoryStatsElapsedTime |
1.3.6.1.4.1.2636.3.78.1.2.4.1.3 |
| The length of time that the Measurement Interval ran for,
in 0.01 seconds.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TimeInterval |
|
|
| jnxSoamLmHistoryStatsSuspect |
1.3.6.1.4.1.2636.3.78.1.2.4.1.4 |
| Whether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| jnxSoamLmHistoryStatsForwardTransmittedFrames |
1.3.6.1.4.1.2636.3.78.1.2.4.1.5 |
| This object contains the number of frames transmitted in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of OAM
ETH-SLM frames only.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryStatsForwardReceivedFrames |
1.3.6.1.4.1.2636.3.78.1.2.4.1.6 |
| This object contains the number of frames received in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of OAM
ETH-SLM frames only.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryStatsForwardMinFlr |
1.3.6.1.4.1.2636.3.78.1.2.4.1.7 |
| This object contains the minimum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryStatsForwardMaxFlr |
1.3.6.1.4.1.2636.3.78.1.2.4.1.8 |
| This object contains the maximum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryStatsForwardAvgFlr |
1.3.6.1.4.1.2636.3.78.1.2.4.1.9 |
| This object contains the average one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryStatsBackwardTransmittedFrames |
1.3.6.1.4.1.2636.3.78.1.2.4.1.10 |
| This object contains the number of frames transmitted in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryStatsBackwardReceivedFrames |
1.3.6.1.4.1.2636.3.78.1.2.4.1.11 |
| This object contains the number of frames received in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryStatsBackwardMinFlr |
1.3.6.1.4.1.2636.3.78.1.2.4.1.12 |
| This object contains the minimum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryStatsBackwardMaxFlr |
1.3.6.1.4.1.2636.3.78.1.2.4.1.13 |
| This object contains the maximum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryStatsBackwardAvgFlr |
1.3.6.1.4.1.2636.3.78.1.2.4.1.14 |
| This object contains the average one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryStatsSoamPdusSent |
1.3.6.1.4.1.2636.3.78.1.2.4.1.15 |
| This object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm,
or lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames
transmitted.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryStatsSoamPdusReceived |
1.3.6.1.4.1.2636.3.78.1.2.4.1.16 |
| This object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm,
or lmCcm. This object indicates the number of LMR, CCM, or SLR
SOAM frames received.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamDmCfgEntry |
1.3.6.1.4.1.2636.3.78.1.3.1.1 |
| The conceptual row of jnxSoamDmCfgTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamDmCfgEntry |
|
|
| jnxSoamDmCfgMeasurementEnable |
1.3.6.1.4.1.2636.3.78.1.3.1.1.5 |
| A vector of bits that indicates the type of SOAM DM counters that
are enabled.
A bit set to '1' enables the specific SOAM DM counter.
A bit set to '0' disables the SOAM DM counter.
If a particular SOAM DM counter is not supported the BIT value is
set to '0'.
Not all SOAM DM counters are supported for all SOAM DM types.
This object can only be written at row creation time and cannot be
modified once it has been created.
bSoamPdusSent(0)
Enables/disables the jnxSoamDmCurrentStatsSoamPdusSent
and jnxSoamDmHistoryStatsSoamPdusSent counters.
bSoamPdusReceived(1)
Enables/disables the jnxSoamDmCurrentStatsSoamPdusReceived
and jnxSoamDmHistoryStatsSoamPdusReceived counters.
bFrameDelayTwoWayBins(2)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayFrameDelay'.
bFrameDelayTwoWayMin(3)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayMin
and jnxSoamDmHistoryStatsFrameDelayTwoWayMin counters.
bFrameDelayTwoWayMax(4)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayMax
and jnxSoamDmHistoryStatsFrameDelayTwoWayMax counters.
bFrameDelayTwoWayAvg(5)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayAvg
and jnxSoamDmHistoryStatsFrameDelayTwoWayAvg counters.
bFrameDelayForwardBins(6)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardFrameDelay'.
bFrameDelayForwardMin(7)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardMin
and jnxSoamDmHistoryStatsFrameDelayForwardMin counters.
bFrameDelayForwardMax(8)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardMax
and jnxSoamDmHistoryStatsFrameDelayForwardMax counters.
bFrameDelayForwardAvg(9)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardAvg
and jnxSoamDmHistoryStatsFrameDelayForwardAvg counters.
bFrameDelayBackwardBins(10)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardFrameDelay'.
bFrameDelayBackwardMin(11)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardMin
and jnxSoamDmHistoryStatsFrameDelayBackwardMin counters.
bFrameDelayBackwardMax(12)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardMax
and jnxSoamDmHistoryStatsFrameDelayBackwardMax counters.
bFrameDelayBackwardAvg(13)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardAvg
and jnxSoamDmHistoryStatsFrameDelayBackwardAvg counters.
bIfdvForwardBins(14)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardIfdv'.
bIfdvForwardMin(15)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardMin
and jnxSoamDmHistoryStatsIfdvForwardMin counters.
bIfdvForwardMax(16)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardMax
and jnxSoamDmHistoryStatsIfdvForwardMax counters.
bIfdvForwardAvg(17)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardAvg
and jnxSoamDmHistoryStatsIfdvForwardAvg counters.
bIfdvBackwardBins(18)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardIfdv'.
bIfdvBackwardMin(19)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardMin
and jnxSoamDmHistoryStatsIfdvBackwardMin counters.
bIfdvBackwardMax(20)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardMax
and jnxSoamDmHistoryStatsIfdvBackwardMax counters.
bIfdvBackwardAvg(21)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardAvg
and jnxSoamDmHistoryStatsIfdvBackwardAvg counters.
bIfdvTwoWayBins(22)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayIfdv'.
bIfdvTwoWayMin(23)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayMin
and jnxSoamDmHistoryStatsIfdvTwoWayMin counters.
bIfdvTwoWayMax(24)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayMax
and jnxSoamDmHistoryStatsIfdvTwoWayMax counters.
bIfdvTwoWayAvg(25)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayAvg
and jnxSoamDmHistoryStatsIfdvTwoWayAvg counters.
bFrameDelayRangeForwardBins(26)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardFrameDelayRange'.
bFrameDelayRangeForwardMax(27)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeForwardMax
and jnxSoamDmHistoryStatsFrameDelayRangeForwardMax counters.
bFrameDelayRangeForwardAvg(28)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg
and jnxSoamDmHistoryStatsFrameDelayRangeForwardAvg counters.
bFrameDelayRangeBackwardBins(29)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardFrameDelayRange'.
bFrameDelayRangeBackwardMax(30)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax
and jnxSoamDmHistoryStatsFrameDelayRangeBackwardMax counters.
bFrameDelayRangeBackwardAvg(31)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg
and jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvg counters.
bFrameDelayRangeTwoWayBins(32)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayFrameDelayRange'.
bFrameDelayRangeTwoWayMax(33)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax
and jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMax counters.
bFrameDelayRangeTwoWayAvg(34)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg
and jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvg counters.
bMeasuredStatsFrameDelayTwoWay(35)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayTwoWay
counter.
bMeasuredStatsFrameDelayForward(36)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayForward
counter.
bMeasuredStatsFrameDelayBackward(37)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayBackward
counter.
bMeasuredStatsIfdvTwoWay(38)
Enables/disables the jnxSoamDmMeasuredStatsIfdvTwoWay
counter.
bMeasuredStatsIfdvForward(39)
Enables/disables the jnxSoamDmMeasuredStatsIfdvForward
counter.
bMeasuredStatsIfdvBackward(40)
Enables/disables the jnxSoamDmMeasuredStatsIfdvBackward
counter.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BITS |
bSoamPdusSent(0), bSoamPdusReceived(1), bFrameDelayTwoWayBins(2), bFrameDelayTwoWayMin(3), bFrameDelayTwoWayMax(4), bFrameDelayTwoWayAvg(5), bFrameDelayForwardBins(6), bFrameDelayForwardMin(7), bFrameDelayForwardMax(8), bFrameDelayForwardAvg(9), bFrameDelayBackwardBins(10), bFrameDelayBackwardMin(11), bFrameDelayBackwardMax(12), bFrameDelayBackwardAvg(13), bIfdvForwardBins(14), bIfdvForwardMin(15), bIfdvForwardMax(16), bIfdvForwardAvg(17), bIfdvBackwardBins(18), bIfdvBackwardMin(19), bIfdvBackwardMax(20), bIfdvBackwardAvg(21), bIfdvTwoWayBins(22), bIfdvTwoWayMin(23), bIfdvTwoWayMax(24), bIfdvTwoWayAvg(25), bFrameDelayRangeForwardBins(26), bFrameDelayRangeForwardMax(27), bFrameDelayRangeForwardAvg(28), bFrameDelayRangeBackwardBins(29), bFrameDelayRangeBackwardMax(30), bFrameDelayRangeBackwardAvg(31), bFrameDelayRangeTwoWayBins(32), bFrameDelayRangeTwoWayMax(33), bFrameDelayRangeTwoWayAvg(34), bMeasuredStatsFrameDelayTwoWay(35), bMeasuredStatsFrameDelayForward(36), bMeasuredStatsFrameDelayBackward(37), bMeasuredStatsIfdvTwoWay(38), bMeasuredStatsIfdvForward(39), bMeasuredStatsIfdvBackward(40) |
|
| jnxSoamDmCfgHistoryClear |
1.3.6.1.4.1.2636.3.78.1.3.1.1.21 |
| This object when written clears the Delay Measurement history
tables (jnxSoamDmHistoryStatsTable)
- all rows are deleted. When read the value always returns 'false'.
Writing this value does not change the current stat table,
nor any of the items in the configuration table.
Writing this object at row creation has no effect.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| jnxSoamDmMeasuredStatsEntry |
1.3.6.1.4.1.2636.3.78.1.3.2.1 |
| The conceptual row of jnxSoamDmMeasuredStatsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamDmMeasuredStatsEntry |
|
|
| jnxSoamDmCurrentStatsEntry |
1.3.6.1.4.1.2636.3.78.1.3.3.1 |
| The conceptual row of jnxSoamDmCurrentStatsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamDmCurrentStatsEntry |
|
|
| jnxSoamDmHistoryStatsTable |
1.3.6.1.4.1.2636.3.78.1.3.4 |
| This table contains the results for history Measurement
Intervals in a SOAM Delay Measurement session.
Rows of this table are created automatically
by the SNMP Agent when the Delay Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the Measurement Interval history
statistics for a Delay Measurement session for the defined MEP. This
table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific DM session on the selected MEP. The fifth index is the
Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval can be deleted (row deletion). If the measurement
interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
The objects in this table apply regardless of the value of
jnxSoamDmCfgType unless otherwise specified in the object description.
Backward and two-way statistic objects are undefined if jnxSoamDmCfgType
is dm1DmRx.
Except for jnxSoamDmHistoryStatsIndex, jnxSoamDmHistoryStatsEndTime,
jnxSoamDmHistoryStatsElapsedTime and jnxSoamDmHistoryStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
JnxSoamDmHistoryStatsEntry |
|
| jnxSoamDmHistoryStatsEntry |
1.3.6.1.4.1.2636.3.78.1.3.4.1 |
| The conceptual row of jnxSoamDmHistoryStatsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamDmHistoryStatsEntry |
|
|
| jnxSoamDmHistoryStatsIndex |
1.3.6.1.4.1.2636.3.78.1.3.4.1.1 |
| The index for the Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsEndTime |
1.3.6.1.4.1.2636.3.78.1.3.4.1.2 |
| The time that the Measurement Interval ended.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| jnxSoamDmHistoryStatsElapsedTime |
1.3.6.1.4.1.2636.3.78.1.3.4.1.3 |
| The length of time that the Measurement Interval ran for,
in 0.01 seconds.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TimeInterval |
|
|
| jnxSoamDmHistoryStatsSuspect |
1.3.6.1.4.1.2636.3.78.1.3.4.1.4 |
| Whether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| jnxSoamDmHistoryStatsFrameDelayTwoWayMin |
1.3.6.1.4.1.2636.3.78.1.3.4.1.5 |
| This object contains the minimum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayTwoWayMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.6 |
| This object contains the maximum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayTwoWayAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.7 |
| This object contains the average two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayForwardMin |
1.3.6.1.4.1.2636.3.78.1.3.4.1.8 |
| This object contains the minimum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayForwardMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.9 |
| This object contains the maximum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayForwardAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.10 |
| This object contains the average one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayBackwardMin |
1.3.6.1.4.1.2636.3.78.1.3.4.1.11 |
| This object contains the minimum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayBackwardMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.12 |
| This object contains the maximum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayBackwardAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.13 |
| This object contains the average one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvForwardMin |
1.3.6.1.4.1.2636.3.78.1.3.4.1.14 |
| This object contains the minimum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvForwardMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.15 |
| This object contains the maximum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvForwardAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.16 |
| This object contains the average one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvBackwardMin |
1.3.6.1.4.1.2636.3.78.1.3.4.1.17 |
| This object contains the minimum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvBackwardMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.18 |
| This object contains the maximum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvBackwardAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.19 |
| This object contains the average one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvTwoWayMin |
1.3.6.1.4.1.2636.3.78.1.3.4.1.20 |
| This object contains the minimum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvTwoWayMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.21 |
| This object contains the maximum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsIfdvTwoWayAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.22 |
| This object contains the average two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsSoamPdusSent |
1.3.6.1.4.1.2636.3.78.1.3.4.1.23 |
| This object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamDmCfgType is dmDmm or dm1DmTx and
is undefined if jnxSoamDmCfgType is dm1DmRx. It indicates the
number of DMM or 1DM SOAM frames transmitted.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamDmHistoryStatsSoamPdusReceived |
1.3.6.1.4.1.2636.3.78.1.3.4.1.24 |
| This object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object indicates the number of DMR and 1DM SOAM frames
received. This object applies when jnxSoamDmCfgType is dmDmm or
dm1DmRx and is undefined if jnxSoamDmCfgType is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayRangeForwardMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.25 |
| This object contains the maximum one-way Frame Delay Range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayRangeForwardAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.26 |
| This object contains the average one-way Frame Delay Range
in the forward direction calculated by this MEP for this
Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayRangeBackwardMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.27 |
| This object contains the maximum one-way Frame Delay Range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.28 |
| This object contains the average one-way Frame Delay Range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMax |
1.3.6.1.4.1.2636.3.78.1.3.4.1.29 |
| This object contains the maximum two-way Frame Delay Range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvg |
1.3.6.1.4.1.2636.3.78.1.3.4.1.30 |
| This object contains the average two-way Frame Delay Range
Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamLmThresholdCfgEntry |
1.3.6.1.4.1.2636.3.78.1.2.5.1 |
| The conceptual row of jnxSoamLmThresholdCfgTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamLmThresholdCfgEntry |
|
|
| jnxSoamLmCurrentAvailStatsEntry |
1.3.6.1.4.1.2636.3.78.1.2.6.1 |
| The conceptual row of jnxSoamLmCurrentAvailStatsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamLmCurrentAvailStatsEntry |
|
|
| jnxSoamLmHistoryAvailStatsTable |
1.3.6.1.4.1.2636.3.78.1.2.7 |
| This table contains the results for availability history Measurement
Intervals in a SOAM Loss Measurement session.
Rows of this table object are created automatically
by the SNMP Agent when the Loss Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the history statistics for a Loss
Measurement session availability Measurement Interval for the defined
MEP. This table uses five indices. The first three indices are the indices
of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific LM session on the selected MEP. The fifth index index the
specific Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval can be deleted (row deletion). If the availability
Measurement Interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
Except for jnxSoamLmHistoryAvailStatsIndex,
jnxSoamLmHistoryAvailStatsEndTime, jnxSoamLmHistoryAvailStatsElapsedTime and
jnxSoamLmHistoryAvailStatsSuspect, each object in this table applies only
if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
JnxSoamLmHistoryAvailStatsEntry |
|
| jnxSoamLmHistoryAvailStatsEntry |
1.3.6.1.4.1.2636.3.78.1.2.7.1 |
| The conceptual row of jnxSoamLmHistoryAvailStatsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamLmHistoryAvailStatsEntry |
|
|
| jnxSoamLmHistoryAvailStatsIndex |
1.3.6.1.4.1.2636.3.78.1.2.7.1.1 |
| The index for the availability Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1. Measurement Intervals
for availability (stored in this table) are based on
jnxSoamLmCfgAvailabilityMeasurementInterval and are indexed independently
of Measurement Intervals for FLR (stored in jnxSoamLmHistoryStatsTable).
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamLmHistoryAvailStatsEndTime |
1.3.6.1.4.1.2636.3.78.1.2.7.1.2 |
| The time that the Measurement Interval ended.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| jnxSoamLmHistoryAvailStatsElapsedTime |
1.3.6.1.4.1.2636.3.78.1.2.7.1.3 |
| The length of time that the Measurement Interval ran for,
in 0.01 seconds.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TimeInterval |
|
|
| jnxSoamLmHistoryAvailStatsSuspect |
1.3.6.1.4.1.2636.3.78.1.2.7.1.4 |
| Whether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| jnxSoamLmHistoryAvailStatsForwardHighLoss |
1.3.6.1.4.1.2636.3.78.1.2.7.1.5 |
| This object is the number of high loss intervals (HLI) over
time in the forward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamLmHistoryAvailStatsBackwardHighLoss |
1.3.6.1.4.1.2636.3.78.1.2.7.1.6 |
| This object is the number of high loss intervals (HLI) over
time in the backward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLoss |
1.3.6.1.4.1.2636.3.78.1.2.7.1.7 |
| This object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss |
1.3.6.1.4.1.2636.3.78.1.2.7.1.8 |
| This object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamLmHistoryAvailStatsForwardAvailable |
1.3.6.1.4.1.2636.3.78.1.2.7.1.9 |
| This object contains the number of availability indicators
evaluated as available in the forward direction by this MEP during
this Measurement Interval.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryAvailStatsBackwardAvailable |
1.3.6.1.4.1.2636.3.78.1.2.7.1.10 |
| This object contains the number of availability indicators
evaluated as available in the backward direction by this MEP during
this Measurement Interval.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryAvailStatsForwardUnavailable |
1.3.6.1.4.1.2636.3.78.1.2.7.1.11 |
| This object contains the number of availability indicators
evaluated as unavailable in the forward direction by this MEP during
this Measurement Interval.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryAvailStatsBackwardUnavailable |
1.3.6.1.4.1.2636.3.78.1.2.7.1.12 |
| This object contains the number of availability indicators
evaluated as unavailable in the backward direction by this MEP
during this Measurement Interval.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamLmHistoryAvailStatsForwardMinFlr |
1.3.6.1.4.1.2636.3.78.1.2.7.1.13 |
| This object contains the minimum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryAvailStatsForwardMaxFlr |
1.3.6.1.4.1.2636.3.78.1.2.7.1.14 |
| This object contains the maximum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryAvailStatsForwardAvgFlr |
1.3.6.1.4.1.2636.3.78.1.2.7.1.15 |
| This object contains the average one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryAvailStatsBackwardMinFlr |
1.3.6.1.4.1.2636.3.78.1.2.7.1.16 |
| This object contains the minimum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryAvailStatsBackwardMaxFlr |
1.3.6.1.4.1.2636.3.78.1.2.7.1.17 |
| This object contains the maximum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamLmHistoryAvailStatsBackwardAvgFlr |
1.3.6.1.4.1.2636.3.78.1.2.7.1.18 |
| This object contains the average one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 3458 0.001 percent.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..100000 |
|
| jnxSoamDmThresholdCfgEntry |
1.3.6.1.4.1.2636.3.78.1.3.5.1 |
| The conceptual row of jnxSoamDmThresholdCfgTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamDmThresholdCfgEntry |
|
|
| jnxSoamDmThresholdCfgEnable |
1.3.6.1.4.1.2636.3.78.1.3.5.1.2 |
| A vector of bits that indicates the type of SOAM DM threshold
notifications that are enabled.
A bit set to '1' enables the specific SOAM DM threshold notification
and when the specific counter is enabled and the threshold is crossed a
notification is generated.
A bit set to '0' disables the specific SOAM DM threshold notification.
If a particular SOAM DM threshold is not supported the BIT value is
set to '0'.
bJnxSoamDmMeasuredFrameDelayTwoWayThreshold(0)
Enables/disables measured frame two-way delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayTwoWay value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayTwoWayThreshold(1)
Enables/disables maximum frame two-way delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayTwoWayMax value is
greater than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayTwoWayThreshold(2)
Enables/disables average frame two-way delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvTwoWayThreshold(3)
Enables/disables measured frame IFDV two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvTwoWay value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvTwoWayThreshold(4)
Enables/disables maximum frame IFDV two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvTwoWayMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvTwoWayThreshold(5)
Enables/disables average frame IFDV two-way threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeTwoWayThreshold(6)
Enables/disables maximum Frame Delay Range two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeTwoWayThreshold(7)
Enables/disables average Frame Delay Range two-way threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredFrameDelayForwardThreshold(8)
Enables/disables measured forward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayForward value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayForwardThreshold(9)
Enables/disables maximum forward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayForwardMax value is
greater than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayForwardThreshold(10)
Enables/disables average forward frame delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvForwardThreshold(11)
Enables/disables measured frame IFDV forward threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvForward value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvForwardThreshold(12)
Enables/disables maximum frame IFDV forward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvForwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvForwardThreshold(13)
Enables/disables average frame IFDV forward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeForwardThreshold(14)
Enables/disables maximum Frame Delay Range forward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeForwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeForwardThreshold(15)
Enables/disables average Frame Delay Range forward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredFrameDelayBackwardThreshold(16)
Enables/disables measured backward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayBackward value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayBackwardThreshold(17)
Enables/disables maximum backward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayBackwardMax value is
greater than or equal to threshold value in a
Measurement Interval.
bJnxSoamDmAvgFrameDelayBackwardThreshold(18)
Enables/disables average backward frame delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayBackwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvBackwardThreshold(19)
Enables/disables measured frame IFDV backward threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvBackward value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvBackwardThreshold(20)
Enables/disables maximum frame IFDV backward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvBackwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvBackwardThreshold(21)
Enables/disables average frame IFDV backward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvBackwardAvg value is greater
than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeBackwardThreshold(22)
Enables/disables maximum Frame Delay Range backward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeBackwardThreshold(23)
Enables/disables average Frame Delay Range backward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg value is greater
than or equal to the threshold value.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BITS |
bJnxSoamDmMeasuredFrameDelayTwoWayThreshold(0), bJnxSoamDmMaxFrameDelayTwoWayThreshold(1), bJnxSoamDmAvgFrameDelayTwoWayThreshold(2), bJnxSoamDmMeasuredIfdvTwoWayThreshold(3), bJnxSoamDmMaxIfdvTwoWayThreshold(4), bJnxSoamDmAvgIfdvTwoWayThreshold(5), bJnxSoamDmMaxFrameDelayRangeTwoWayThreshold(6), bJnxSoamDmAvgFrameDelayRangeTwoWayThreshold(7), bJnxSoamDmMeasuredFrameDelayForwardThreshold(8), bJnxSoamDmMaxFrameDelayForwardThreshold(9), bJnxSoamDmAvgFrameDelayForwardThreshold(10), bJnxSoamDmMeasuredIfdvForwardThreshold(11), bJnxSoamDmMaxIfdvForwardThreshold(12), bJnxSoamDmAvgIfdvForwardThreshold(13), bJnxSoamDmMaxFrameDelayRangeForwardThreshold(14), bJnxSoamDmAvgFrameDelayRangeForwardThreshold(15), bJnxSoamDmMeasuredFrameDelayBackwardThreshold(16), bJnxSoamDmMaxFrameDelayBackwardThreshold(17), bJnxSoamDmAvgFrameDelayBackwardThreshold(18), bJnxSoamDmMeasuredIfdvBackwardThreshold(19), bJnxSoamDmMaxIfdvBackwardThreshold(20), bJnxSoamDmAvgIfdvBackwardThreshold(21), bJnxSoamDmMaxFrameDelayRangeBackwardThreshold(22), bJnxSoamDmAvgFrameDelayRangeBackwardThreshold(23) |
|
| jnxSoamDmCfgMeasBinTable |
1.3.6.1.4.1.2636.3.78.1.3.6 |
| This table includes configuration objects for the Delay Measurement
bins to collect stats.
Each row in the table is automatically created when the Delay
Measurement session is defined for the selected MEP. The number of rows
created is based upon three items: the DM type, the number of bins
defined for each type, and whether bins are enabled for each type.
The first four indices are the same as used to create the DM session:
Maintenance Domain, MaNet, MEP identification, and jnxSoamDmCfgIndex. The
fifth index is the type of bin, and the sixth index is the bin number.
For a dmDmm session all nine types of bins can be created. For a dm1DmmTx
session no bins are created. For a dm1DmmRx session only types
forwardFrameDelay, forwardIfdv, and forwardFrameDelayRange can be created.
The number of bins created for a bin type is based upon: the
jnxSoamDmCfgNumMeasBinsPerFrameDelayInterval object, the
jnxSoamDmCfgNumMeasBinsPerInterFrameDelayVariationInterval object, the
jnxSoamDmCfgNumMeasBinsPerFrameDelayRangeInterval object, and
the jnxSoamDmCfgMeasurementEnable object.
For instance, if a dmDmm session with Bins per Frame Delay Interval
set to 5, Bins per Frame Delay Variation Interval set to 3, and Frame
Delay Range set to 2 (default), all of the appropriate bits set in
jnxSoamDmMeasurementCfgEnable, the following number of rows would be
created:
For bin types TwoWayFrameDelay(1), forwardFrameDelay(2), and
backwardFrameDelay(3) = 5 bins * 3 types = 15 rows
For bin types TwoWayIfdv(4), forwardIfdv(5), backwardIfdv(6) =
3 bins * 3 types = 9 rows.
For bins types twoWayFrameDelayRange(7), forwardFrameDelayRange(8),
backwardFrameDelayRange(9) =
2 bins * 3 types = 6 rows.
This gives a total of 30 rows created for the DMM session example.
Each value in the bin defaults to 5000us greater than the previous bin,
with the first bin default value set to 0.
For the delay example above (5 bins), the following default values
would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < 10,000us)
bin 3: 10000 (range is 10,000us <= measurement < 15,000us)
bin 4: 15000 (range is 15,000us <= measurement < 20,000us)
bin 5: 20000 (range is 20,000us <= measurement < infinity)
For the delay variation example above (3 bins), the following default
values would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < 10,000us)
bin 3: 10000 (range is 10,000us <= measurement < infinity)
For the frame delay range example above (2 bins), the following default
values would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < infinity)
The writable objects in this table need to be persistent upon reboot
or restart of a device.
Rows are only created if the corresponding measurement type has been enabled
via the jnxSoamDmCfgMeasurementEnable object.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
JnxSoamDmCfgMeasBinEntry |
|
| jnxSoamDmCfgMeasBinEntry |
1.3.6.1.4.1.2636.3.78.1.3.6.1 |
| The conceptual row of jnxSoamDmCfgMeasBinTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamDmCfgMeasBinEntry |
|
|
| jnxSoamDmCfgMeasBinLowerBound |
1.3.6.1.4.1.2636.3.78.1.3.6.1.3 |
| This object specifies the lower boundary for a
measurement bin. The upper boundary is defined by the next bin
value or infinite for the last bin defined.
The measurement boundary for each measurement bin is to
be larger than the measurement boundary of the preceding
measurement bin. By default, the next bin is set to 5000us larger
than the lower bin boundary.
The values in a bin boundary object represents the time range
used to segregate delay data into the appropriate statistical
data bin. For five bins with default values, each bin has the
following time range:
bin 1 = 0, range is 0us <= measurement < 5,000us
bin 2 = 5000, range is 5,000us <= measurement < 10,000us
bin 3 = 10000, range is 10,000us <= measurement < 15,000us
bin 4 = 15000, range is 15,000us <= measurement < 20,000us
< infinity
The first bin boundary (jnxSoamDmCfgBinNumber set to 1) always contains
the value of 0. Attempting to write a non-zero value to this bin will
result in an error.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| jnxSoamDmCurrentStatsBinsEntry |
1.3.6.1.4.1.2636.3.78.1.3.7.1 |
| The conceptual row of jnxSoamDmCurrentStatsBinsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamDmCurrentStatsBinsEntry |
|
|
| jnxSoamDmHistoryStatsBinsTable |
1.3.6.1.4.1.2636.3.78.1.3.8 |
| This table contains the result bins for the history Measurement
Intervals in a SOAM Delay Measurement session.
Rows of this table are created automatically
by the SNMP Agent when the Delay Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the Measurement Interval history
statistics for a specific bin in a Delay Measurement session for the
defined MEP. This table uses seven indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP. The
fifth index is the Measurement Interval. The sixth index is the
specific bin type. The seventh index is the specific bin number.
Rows in this table pertaining to a given Measurement Interval are
row in the
jnxSoamDmHistoryStatsTable is deleted.
The objects in this table are ignored if jnxSoamDmCfgType is 1DmTx.
This table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table need to be persistent upon reboot
or restart of a device.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
JnxSoamDmHistoryStatsBinsEntry |
|
| jnxSoamDmHistoryStatsBinsEntry |
1.3.6.1.4.1.2636.3.78.1.3.8.1 |
| The conceptual row of jnxSoamDmHistoryStatsBinsTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
JnxSoamDmHistoryStatsBinsEntry |
|
|
| jnxSoamDmHistoryStatsBinsCounter |
1.3.6.1.4.1.2636.3.78.1.3.8.1.1 |
| This object contains the count of the number of completed
measurements initiated in this Measurement Interval whose value
falls within the range specified for this bin (that is, greater
than or equal to the measurement boundary for the bin, and
(unless the bin is the last bin) less than the measurement
boundary for the following bin.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| jnxSoamPmThresholdCrossingAlarm |
1.3.6.1.4.1.2636.3.78.0.3 |
| An jnxSoamPmThresholdCrossingAlarm notification is sent if the
following conditions are met for a particular type.
For an aboveAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdAboveAlarm is enabled;
and
d) the measured value of the parameter exceeds the value configured in
the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdAboveAlarm; and
e) no previous jnxSoamPmThresholdCrossingAlarm notifications with type
aboveAlarm have been sent relating to the same threshold in the
jnxSoamLmThresholdCfgTable or jnxSoamDmThresholdCfgTable and the
same parameter, during this Measurement Interval.
For a setAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdSetClearAlarm is enabled;
and
d) the measured value of the parameter exceeds the value configured in
the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdSetClearAlarm for the Measurement Interval; and
e) the previous measured value did not
exceed the value configured in the jnxSoamLmThresholdCfgTable for
a LM crossing entry or jnxSoamDmThresholdCfgTable for a DM crossing
entry for a type of bPmThresholdSetClearAlarm.
For a clearAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdSetClearAlarm is enabled;
and
d) the measured value of the parameter did not exceed the value configured
in the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdSetClearAlarm for the Measurement Interval; and
e) the previous measured value did
exceed the value configured in the jnxSoamLmThresholdCfgTable for
a LM crossing entry or jnxSoamDmThresholdCfgTable for a DM crossing
entry for a type of bPmThresholdSetClearAlarm.
In the case of thresholds applied to a maximum or average measurement
counter, the previous measured value is the value of the counter at the
end of the preceding Measurement Interval. In the case of thresholds
applied to the last measured value, it is the previous measured value.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the LM or DM session reporting the threshold
crossing by the indices in the jnxSoamPmNotificationCfgThresholdId object,
including dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier,
and the jnxSoamLmCfgIndex or jnxSoamDmCfgIndex.
An agent is not to generate more than one jnxSoamLmThresholdCrossingAlarm
'notification-event' of a given type per LM or DM session as specified
by jnxSoamPmNotificationCfgAlarmInterval. A 'notification-event' is the
transmission of a single notification to a list of notification
destinations.
If additional threshold crossing events occur within the
jnxSoamPmNotificationCfgAlarmInterval period, then notification
generation for these changes are suppressed by the agent until
the current alarm interval expires. At the end of an alarm interval
period, one notification-event is generated if any threshold
crossing events occurred since the start of the alarm interval period.
In such a case, another alarm interval period is started right away.
|
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
