JNX-PPPOE-MIB

File: JNX-PPPOE-MIB.mib (52170 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB JUNIPER-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
Counter32 Unsigned32 Counter64
TEXTUAL-CONVENTION DisplayString RowStatus
TruthValue MacAddress MODULE-COMPLIANCE
OBJECT-GROUP InterfaceIndex InterfaceIndexOrZero
jnxPppoeMibRoot

Defined Types

JnxPPPoEServiceNameAction  
The set of Service-name action types. drop no PADO packet will be sent. terminate a PADO packet will be sent.
TEXTUAL-CONVENTION    
  INTEGER drop(0), terminate(1)  

JnxPPPoEIfEntry  
SEQUENCE    
  jnxPPPoEIfIfIndex InterfaceIndex
  jnxPPPoEIfMaxNumSessions INTEGER
  jnxPPPoEIfRowStatus RowStatus
  jnxPPPoEIfLowerIfIndex InterfaceIndexOrZero
  jnxPPPoEIfAcName DisplayString
  jnxPPPoEIfDupProtect INTEGER
  jnxPPPoEIfPADIFlag INTEGER
  jnxPPPoEIfAutoconfig INTEGER
  jnxPPPoEIfServiceNameTable DisplayString
  jnxPPPoEIfPadrRemoteCircuitIdCapture INTEGER
  jnxPPPoEIfMtu Integer32
  jnxPPPoEIfLockoutMin Integer32
  jnxPPPoEIfLockoutMax Integer32
  jnxPPPoEIfDynamicProfile DisplayString

JnxPPPoEIfStatsEntry  
SEQUENCE    
  jnxPPPoEIfStatsRxPADI Counter32
  jnxPPPoEIfStatsTxPADO Counter32
  jnxPPPoEIfStatsRxPADR Counter32
  jnxPPPoEIfStatsTxPADS Counter32
  jnxPPPoEIfStatsRxPADT Counter32
  jnxPPPoEIfStatsTxPADT Counter32
  jnxPPPoEIfStatsRxInvVersion Counter32
  jnxPPPoEIfStatsRxInvCode Counter32
  jnxPPPoEIfStatsRxInvTags Counter32
  jnxPPPoEIfStatsRxInvSession Counter32
  jnxPPPoEIfStatsRxInvTypes Counter32
  jnxPPPoEIfStatsRxInvPackets Counter32
  jnxPPPoEIfStatsRxInsufficientResources Counter32
  jnxPPPoEIfStatsTxPADM Counter32
  jnxPPPoEIfStatsTxPADN Counter32
  jnxPPPoEIfStatsRxInvTagLength Counter32
  jnxPPPoEIfStatsRxInvLength Counter32
  jnxPPPoEIfStatsRxInvPadISession Counter32
  jnxPPPoEIfStatsRxInvPadRSession Counter32

JnxPPPoEIfLockoutEntry  
SEQUENCE    
  jnxPPPoEIfLockoutClientAddress MacAddress
  jnxPPPoEIfLockoutTime Integer32
  jnxPPPoEIfLockoutElapsedTime Integer32
  jnxPPPoEIfLockoutNextTime Integer32

JnxPPPoESubIfEntry  
SEQUENCE    
  jnxPPPoESubIfIndex InterfaceIndex
  jnxPPPoESubIfRowStatus RowStatus
  jnxPPPoESubIfLowerIfIndex InterfaceIndexOrZero
  jnxPPPoESubIfId Unsigned32
  jnxPPPoESubIfSessionId Integer32
  jnxPPPoESubIfMotm DisplayString
  jnxPPPoESubIfUrl DisplayString
  jnxPPPoESubIfSubscriberIdHiWord Unsigned32
  jnxPPPoESubIfSubscriberIdLoWord Unsigned32

JnxPppoeSubIfPerQueueStatsEntry  
SEQUENCE    
  jnxPppoeSubIfQueueIndex INTEGER 0..7
  jnxPppoeSubIfQueueStatsPacketSent Counter64
  jnxPppoeSubIfQueueStatsBytesSent Counter64
  jnxPppoeSubIfQueueStatsPacketDropped Counter64
  jnxPppoeSubIfQueueStatsBytesDropped Counter64
  jnxPppoeSubIfQueueStatsActualBitRate Counter32
  jnxPppoeSubIfQueueStatsActualDroppedBitRate Counter32

JnxPPPoEServiceNameTableEntry  
SEQUENCE    
  jnxPPPoEServiceNameTableName DisplayString
  jnxPPPoEServiceNameTableRowStatus RowStatus

JnxPPPoEServiceNameEntry  
SEQUENCE    
  jnxPPPoEServiceName DisplayString
  jnxPPPoEServiceNameAction JnxPPPoEServiceNameAction
  jnxPPPoEServiceNameDynamicProfile DisplayString
  jnxPPPoEServiceNameRoutingInstance DisplayString
  jnxPPPoEServiceNameMaxSessions Unsigned32
  jnxPPPoEServiceNameRowStatus RowStatus

JnxPPPoEServiceNameAciAriEntry  
SEQUENCE    
  jnxPPPoEServiceNameAgentCircuitId DisplayString
  jnxPPPoEServiceNameAgentRemoteId DisplayString
  jnxPPPoEServiceNameAciAriAction JnxPPPoEServiceNameAction
  jnxPPPoEServiceNameAciAriDynamicProfile DisplayString
  jnxPPPoEServiceNameAciAriRoutingInstance DisplayString
  jnxPPPoEServiceNameAciAriStaticInterface DisplayString
  jnxPPPoEServiceNameAciAriRowStatus RowStatus

Defined Values

jnxPPPoEMIB 1.3.6.1.4.1.2636.3.67.1
The Point-to-Point Protocol over Ethernet (PPPoE) MIB for the Junos product family. This MIB contains managed objects for each of two interface layers: PPPoE interfaces, and PPPoE subinterfaces. For each of these layers, management objects are provided to query for an available interface index, and to create/delete interfaces of that type.
MODULE-IDENTITY    

jnxPPPoEObjects 1.3.6.1.4.1.2636.3.67.1.1
OBJECT IDENTIFIER    

jnxPPPoEIfLayer 1.3.6.1.4.1.2636.3.67.1.1.1
OBJECT IDENTIFIER    

jnxPPPoESubIfLayer 1.3.6.1.4.1.2636.3.67.1.1.2
OBJECT IDENTIFIER    

jnxPPPoESummary 1.3.6.1.4.1.2636.3.67.1.1.3
OBJECT IDENTIFIER    

jnxPPPoEServices 1.3.6.1.4.1.2636.3.67.1.1.4
OBJECT IDENTIFIER    

jnxPPPoENextIfIndex 1.3.6.1.4.1.2636.3.67.1.1.1.1
Coordinate ifIndex value allocation for entries in jnxPPPoEIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
OBJECT-TYPE    
  InterfaceIndexOrZero  

jnxPPPoEIfTable 1.3.6.1.4.1.2636.3.67.1.1.1.2
The parameters for the PPPoEservice on this interface.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPPPoEIfEntry

jnxPPPoEIfEntry 1.3.6.1.4.1.2636.3.67.1.1.1.2.1
The Parameters for a particular PPPoEinterface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/jnxIfTable, and jnxPPPoEIfStatsTable.
OBJECT-TYPE    
  JnxPPPoEIfEntry  

jnxPPPoEIfIfIndex 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.1
The ifIndex value of the corresponding ifEntry.
OBJECT-TYPE    
  InterfaceIndex  

jnxPPPoEIfMaxNumSessions 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.2
The number of sessions allowed on the PPPoEinterface, zero indicates unlimited.
OBJECT-TYPE    
  INTEGER 0..65335  

jnxPPPoEIfRowStatus 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.3
Controls creation/deletion of entries in this table with READ-CREATE maximum access, according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPPPoEIfRowStatus jnxPPPoEIfLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for jnxPPPoEIfIndex must have been determined previously, by reading jnxPPPoENextIfIndex. The interface identified by jnxPPPoEIfLowerIfIndex must exist, and must be an interface type that permits layering of PPPoEabove it. A corresponding entry in ifTable/ifXTable/jnxIfTable is created or destroyed as a result of creating or destroying an entry in this table. The following values can be read from this object: active(1)
OBJECT-TYPE    
  RowStatus  

jnxPPPoEIfLowerIfIndex 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.4
The ifIndex of an interface over which this PPPoEinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
OBJECT-TYPE    
  InterfaceIndexOrZero  

jnxPPPoEIfAcName 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.5
The name to use for the AC-NAME tag that is sent in any PADO that is sent on this interface.
OBJECT-TYPE    
  DisplayString Size(0..64)  

jnxPPPoEIfDupProtect 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.6
Flag to allow duplicate MAC addresses.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

jnxPPPoEIfPADIFlag 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.7
This flag controls whether we always respond to a PADI with a PADO regardless of the ability to create the session and allows the session establish phase to resolve it.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

jnxPPPoEIfAutoconfig 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.8
This flags determines whether the upper PPPoEinterface is created dynamically or statically. When enable(1) the interface is created dynamically.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

jnxPPPoEIfServiceNameTable 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.9
Associate a PPPoEService Name Table with this interface for PADI processing.
OBJECT-TYPE    
  DisplayString Size(0..32)  

jnxPPPoEIfPadrRemoteCircuitIdCapture 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.10
This flags determines whether the remote circuit id string will be captured and subsequently used as the NAS-PORT-ID radius attribute when it arrives as a tag in the PADR packet.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

jnxPPPoEIfMtu 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.11
The initial Maximum Transmit Unit (MTU) that the PPPoEmajor interface entity will advertise to the remote entity. If the value of this variable is 1 then the local PPPoEentity will use an MTU value determined by its underlying media interface. If the value of this variable is 2 then the local PPPoEentity will use a value determined by the PPPoEMax-Mtu-Tag transmitted from the client in the PADR packet. If no Max-Mtu-Tag is received, the value defaults to a maximum of 1494. The operational MTU is limited by the MTU of the underlying media interface minus the PPPoEframe overhead.
OBJECT-TYPE    
  Integer32 1 | 2 | 66..65535  

jnxPPPoEIfLockoutMin 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.12
The lower bound, in seconds, of the time range used to specify the duration of the lockout of the client from recognition for the specified interface. This only takes effect if jnxPPPoEIfAutoconfig is set for this interface. The ability to lockout the client in the event of an error in creating a PPP interface is enabled by default. The initial lockout duration is this object's value and increases exponentially for each failure that occurs for the client creating a PPP interface for the PPPoEinterface within the greater of 15 minutes and jnxPPPoEIfLockoutMax. The lockout duration for the client will not exceed jnxPPPoEIfLockoutMax. If the time between creation errors for the PPP interface for this interface is greater than the greater of 15 minutes and jnxPPPoEIfLockoutMax, then the lockout duration reverts to this object's value. To disable the ability to lockout the client from recognition in the event of an error in creating a PPP interface for the specified interface, the value of this object and jnxPPPoEIfLockoutMin must be set to 0. It is not recommended that this lockout feature be disabled except for debugging purposes or when this interface supports more than one session.
OBJECT-TYPE    
  Integer32 0..86400  

jnxPPPoEIfLockoutMax 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.13
The upper bound, in seconds, of the time range used to specify the duration of the lockout of the client from recognition for the specified interface. This only takes effect if jnxPPPoEIfAutoconfig is set for this interface. The ability to lockout the client from recognition in the event of an error in creating a PPP interface is enabled by default. The initial lockout duration is jnxPPPoEIfLockoutMin and increases exponentially for each failure that occurs for the client interface within the greater of 15 minutes and this object's value. The lockout duration for the client will not exceed jnxPPPoEIfLockoutMax. If the time between creation errors for the PPP interface for this interface is greater than the greater of 15 minutes and jnxPPPoEIfLockoutMax, then the lockout duration reverts to jnxPPPoEIfLockoutMin. To disable the ability to lockout the client from recognition in the event of an error in creating a PPP interface for the specified interface, the value of this object and jnxPPPoEIfLockoutMin must be set to 0. It is not recommended that this lockout feature be disabled except for debugging purposes or when this interface supports more than one session.
OBJECT-TYPE    
  Integer32 0..86400  

jnxPPPoEIfDynamicProfile 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.14
Attach dynamic-profile to this interface
OBJECT-TYPE    
  DisplayString  

jnxPPPoEIfStatsTable 1.3.6.1.4.1.2636.3.67.1.1.1.3
The statistics for the PPP over Ethernet Interface for the PPPoE service on this interface.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPPPoEIfStatsEntry

jnxPPPoEIfStatsEntry 1.3.6.1.4.1.2636.3.67.1.1.1.3.1
The statistics for a particular PPPoEInterface.
OBJECT-TYPE    
  JnxPPPoEIfStatsEntry  

jnxPPPoEIfStatsRxPADI 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.1
Number of PADI packets received.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsTxPADO 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.2
Number of PADO packets transmitted.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxPADR 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.3
Number of PADR packets received.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsTxPADS 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.4
Number of PADS packets transmitted.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxPADT 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.5
Number of PADT packets received.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsTxPADT 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.6
Number of PADT packets transmitted.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvVersion 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.7
Number of packets received with invalid version.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvCode 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.8
Number of packets received with invalid code.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvTags 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.9
Number of packets received with invalid tags.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvSession 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.10
Number of packets received with invalid session identifiers. This object became obsolete when separate counters were added for PADI and PADR packets.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvTypes 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.11
Number of packets received with invalid types.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvPackets 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.12
Number of invalid packets received.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInsufficientResources 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.13
Number of session requests that could not be honored due to invalid resources.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsTxPADM 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.14
Number of PADM packets transmitted.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsTxPADN 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.15
Number of PADN packets transmitted.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvTagLength 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.16
Number of packets received with invalid tag length.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvLength 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.17
Number of packets received with invalid length.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvPadISession 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.18
Number of PADI packets received with invalid session identifiers.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfStatsRxInvPadRSession 1.3.6.1.4.1.2636.3.67.1.1.1.3.1.19
Number of PADR packets received with invalid session identifiers.
OBJECT-TYPE    
  Counter32  

jnxPPPoEIfLockoutTable 1.3.6.1.4.1.2636.3.67.1.1.1.4
The lockout configuration and state of a PPPoEclient on this interface.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPPPoEIfLockoutEntry

jnxPPPoEIfLockoutEntry 1.3.6.1.4.1.2636.3.67.1.1.1.4.1
Each entry contains the configuration and state of a particular PPPoEinterface client lockout.
OBJECT-TYPE    
  JnxPPPoEIfLockoutEntry  

jnxPPPoEIfLockoutClientAddress 1.3.6.1.4.1.2636.3.67.1.1.1.4.1.1
The source MAC address if the client.
OBJECT-TYPE    
  MacAddress  

jnxPPPoEIfLockoutTime 1.3.6.1.4.1.2636.3.67.1.1.1.4.1.2
The time duration, in seconds, currently used to lockout the specified encapsulation type from recognition for the specified interface. The reported value is within the range specified by jnxPPPoEIfLockoutMin and jnxPPPoEIfLockoutMax. A value of 0 indicates that no lockout is occurring for the encapsulation type for the specified interface.
OBJECT-TYPE    
  Integer32 0..86400  

jnxPPPoEIfLockoutElapsedTime 1.3.6.1.4.1.2636.3.67.1.1.1.4.1.3
The elapsed time, in seconds, that the specified encapsulation type has been locked-out from recognition for the specified interface. Its value will not exceed that of jnxPPPoEIfLockoutTime. A value of 0 indicates that no lockout is occurring for the encapsulation type for the specified interface.
OBJECT-TYPE    
  Integer32 0..86400  

jnxPPPoEIfLockoutNextTime 1.3.6.1.4.1.2636.3.67.1.1.1.4.1.4
The time duration, in seconds, that will be used to lockout the specified encapsulation type from recognition for the specified interface for the next event that results in a lockout condition. The reported value is within the range specified by jnxPPPoEIfLockoutMin and jnxPPPoEIfLockoutMax. When jnxPPPoEIfEnable is set to enable, a value of 0 indicates that lockout is prevented from occurring for the encapsulation type for the specified interface (i.e., jnxPPPoEIfLockoutMin and jnxPPPoEIfLockoutMax are both set to 0).
OBJECT-TYPE    
  Integer32 0..86400  

jnxPPPoESubIfNextIfIndex 1.3.6.1.4.1.2636.3.67.1.1.2.1
Coordinate ifIndex value allocation for entries in jnxPPPoESubIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
OBJECT-TYPE    
  InterfaceIndexOrZero  

jnxPPPoESubIfTable 1.3.6.1.4.1.2636.3.67.1.1.2.2
This table contains entries for PPPoESubinterfaces present in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPPPoESubIfEntry

jnxPPPoESubIfEntry 1.3.6.1.4.1.2636.3.67.1.1.2.2.1
Each entry describes the characteristics of a PPPoESubinterface. With READ-CREATE maximum access ,creating/deleting entries in this table causes corresponding entries for be created /deleted in ifTable/ifXTable/jnxIfTable.
OBJECT-TYPE    
  JnxPPPoESubIfEntry  

jnxPPPoESubIfIndex 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.1
The ifIndex of the PPPoESubinterface. When creating entries in this table, suitable values for this object are determined by reading jnxPPPoESubNextIfIndex.
OBJECT-TYPE    
  InterfaceIndex  

jnxPPPoESubIfRowStatus 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.2
Controls creation/deletion of entries in this table with READ-CREATE maximum access ,according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPPPoESubIfRowStatus jnxPPPoESubIfLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for jnxPPPoESubIfIndex must have been determined previously, by reading jnxPPPoESubIfNextIfIndex. The interface identified by jnxPPPoESubIfLowerIfIndex must exist, and must be a PPPoEinterface. A positive value configured for jnxPPPoESubIfId must not already be assigned to another subinterface layered onto the same underlying PPPoEinterface. A corresponding entry in ifTable/ifXTable/jnxIfTable is created or destroyed as a result of creating or destroying an entry in this table. The following values can be read from this object: active(1)
OBJECT-TYPE    
  RowStatus  

jnxPPPoESubIfLowerIfIndex 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.3
The ifIndex of a PPPoEinterface over which this PPPoESubinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
OBJECT-TYPE    
  InterfaceIndexOrZero  

jnxPPPoESubIfId 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.4
An integer identifier for the PPPoEsubinterface, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among subinterfaces configured on the same underlying PPPoEinterface. If this object is not configured, or is configured with a value of -1, a nonzero value will be allocated internally and can be retrieved from this object after table entry creation has succeeded. A value of zero for this object is reserved for future use.
OBJECT-TYPE    
  Unsigned32  

jnxPPPoESubIfSessionId 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.5
The current sessionId associated with this sub-interface.
OBJECT-TYPE    
  Integer32 0..65535  

jnxPPPoESubIfMotm 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.6
A message to send via a PADM on the sub-interface when the sub-interface transitions to the ifOperStatusUp state. The client may choose to display this message to the user.
OBJECT-TYPE    
  DisplayString Size(0..127)  

jnxPPPoESubIfUrl 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.7
A URL to be sent via a PADM on the sub-interface when the sub-interface transitions to the ifOperStatusUp state. The client may use this URL as the initial web-page for the user.
OBJECT-TYPE    
  DisplayString Size(0..127)  

jnxPPPoESubIfSubscriberIdHiWord 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.8
The subscriber handle associated with this PPPoEsubinterface which can be used to index into the JUNIPER-SUBSCRIBER-MIB table entries. This object is equal to the most significant 32 bit of the 64 bit subscriber id.
OBJECT-TYPE    
  Unsigned32  

jnxPPPoESubIfSubscriberIdLoWord 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.9
The subscriber handle associated with this PPPoEsubinterface which can be used to index into the JUNIPER-SUBSCRIBER-MIB table entries. This object is equal to the least significant 32 bit of the 64 bit subscriber id.
OBJECT-TYPE    
  Unsigned32  

jnxPppoeSubIfQueueStatsTable 1.3.6.1.4.1.2636.3.67.1.1.2.3
Table containing the Queue parameters for the PPPoEsessions.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPppoeSubIfPerQueueStatsEntry

jnxPppoeSubIfPerQueueStatsEntry 1.3.6.1.4.1.2636.3.67.1.1.2.3.1
The statistics for a particular trrafic class queue for PPPoEsub Interface(i.e. session). ). Forwarding class to queue number mapping is not always one-to-one. Forwarding classes and queues are the same only when default forwarding-class-to-queue mapping is in effect
OBJECT-TYPE    
  JnxPppoeSubIfPerQueueStatsEntry  

jnxPppoeSubIfQueueIndex 1.3.6.1.4.1.2636.3.67.1.1.2.3.1.1
This attribute returns the queue index ranging from 0 to 7 of the queue configure on the PPPoEsubinterface to support the traffic class for PPPoEsession configured on that subinterface. Forwarding class to queue number mapping is not always one-to-one. Forwarding classes and queues are the same only when default forwarding-class-to-queue mapping is in effect.
OBJECT-TYPE    
  INTEGER 0..7  

jnxPppoeSubIfQueueStatsPacketSent 1.3.6.1.4.1.2636.3.67.1.1.2.3.1.2
This attribute returns the counts of number of packet sent per PPPoEsession and per queue.
OBJECT-TYPE    
  Counter64  

jnxPppoeSubIfQueueStatsBytesSent 1.3.6.1.4.1.2636.3.67.1.1.2.3.1.3
This attribute returns the counts of number of bytes sent per PPPoEsession and per queue.
OBJECT-TYPE    
  Counter64  

jnxPppoeSubIfQueueStatsPacketDropped 1.3.6.1.4.1.2636.3.67.1.1.2.3.1.4
This attribute returns the number of packet dropped per PPPoEsession and per queue.
OBJECT-TYPE    
  Counter64  

jnxPppoeSubIfQueueStatsBytesDropped 1.3.6.1.4.1.2636.3.67.1.1.2.3.1.5
This attribute returns the number of bytes dropped per PPPoEsession and per queue.
OBJECT-TYPE    
  Counter64  

jnxPppoeSubIfQueueStatsActualBitRate 1.3.6.1.4.1.2636.3.67.1.1.2.3.1.6
This attribute returns the actual bit rate for per PPPoEsession and per queue.
OBJECT-TYPE    
  Counter32  

jnxPppoeSubIfQueueStatsActualDroppedBitRate 1.3.6.1.4.1.2636.3.67.1.1.2.3.1.7
This attribute returns the actual dropped bit rate for per PPPoEsession and per queue.
OBJECT-TYPE    
  Counter32  

jnxPPPoEServiceNameTableTable 1.3.6.1.4.1.2636.3.67.1.1.4.1
This table contains entries for the PPPoEService-name tables.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPPPoEServiceNameTableEntry

jnxPPPoEServiceNameTableEntry 1.3.6.1.4.1.2636.3.67.1.1.4.1.1
The parameters for the PPPoEservice-name table.
OBJECT-TYPE    
  JnxPPPoEServiceNameTableEntry  

jnxPPPoEServiceNameTableName 1.3.6.1.4.1.2636.3.67.1.1.4.1.1.1
Service-name table name.
OBJECT-TYPE    
  DisplayString Size(1..32)  

jnxPPPoEServiceNameTableRowStatus 1.3.6.1.4.1.2636.3.67.1.1.4.1.1.2
Controls creation/deletion of entries in this table with READ-CREATE maximum access,according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPPPoEServiceNameTableRowStatus jnxPPPoEServiceNameTableName The Empty Service and Any service will be automatically configured for each Service Name Table created. On creating or deleting an entry in this table will create/destroy an entry for Service and service in jnxServiceNameTable. A corresponding entry in jnxServiceNameTable gets created or destroyed as a result of creating or destroying an entry in this table. The following values can be read from this object: active(1)
OBJECT-TYPE    
  RowStatus  

jnxPPPoEServiceNameTable 1.3.6.1.4.1.2636.3.67.1.1.4.2
This table contains entries for the PPPoEService-names.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPPPoEServiceNameEntry

jnxPPPoEServiceNameEntry 1.3.6.1.4.1.2636.3.67.1.1.4.2.1
The parameters for the PPPoEservice-name table entry.
OBJECT-TYPE    
  JnxPPPoEServiceNameEntry  

jnxPPPoEServiceName 1.3.6.1.4.1.2636.3.67.1.1.4.2.1.1
Service-name tag value.
OBJECT-TYPE    
  DisplayString Size(1..64)  

jnxPPPoEServiceNameAction 1.3.6.1.4.1.2636.3.67.1.1.4.2.1.2
Identifies the behavior when the the Service-name tag is received in a PADI frame.
OBJECT-TYPE    
  JnxPPPoEServiceNameAction  

jnxPPPoEServiceNameDynamicProfile 1.3.6.1.4.1.2636.3.67.1.1.4.2.1.3
Dynamic Profile associated with a Service-name.
OBJECT-TYPE    
  DisplayString  

jnxPPPoEServiceNameRoutingInstance 1.3.6.1.4.1.2636.3.67.1.1.4.2.1.4
Routing Instance associated with a Service-name.
OBJECT-TYPE    
  DisplayString  

jnxPPPoEServiceNameMaxSessions 1.3.6.1.4.1.2636.3.67.1.1.4.2.1.5
The Max Sessions value used to cap the number of active PPPoEssessions that may be established with the specified Service entry.
OBJECT-TYPE    
  Unsigned32  

jnxPPPoEServiceNameRowStatus 1.3.6.1.4.1.2636.3.67.1.1.4.2.1.6
Controls creation/deletion of entries in this table with READ-CREATE maximum access ,according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPPPoEServiceNameRowStatus The Service name is configured via the INDEX specified. A corresponding entry in jnxPPPoEServiceNameAciAriTable is destroyed as a result of destroying an entry in this table. The following values can be read from this object: active(1)
OBJECT-TYPE    
  RowStatus  

jnxPPPoEServiceNameAciAriTable 1.3.6.1.4.1.2636.3.67.1.1.4.3
This table contains entries for the PPPoEServicename AciAri entries.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPPPoEServiceNameAciAriEntry

jnxPPPoEServiceNameAciAriEntry 1.3.6.1.4.1.2636.3.67.1.1.4.3.1
The parameters for the PPPoEservice-name AciAri table entry.
OBJECT-TYPE    
  JnxPPPoEServiceNameAciAriEntry  

jnxPPPoEServiceNameAgentCircuitId 1.3.6.1.4.1.2636.3.67.1.1.4.3.1.1
ACI tag values that the PPPoEclient would send in the PADI/PADR control packet.
OBJECT-TYPE    
  DisplayString Size(0..64)  

jnxPPPoEServiceNameAgentRemoteId 1.3.6.1.4.1.2636.3.67.1.1.4.3.1.2
ACI tag values that the PPPoEclient would send in the PADI/PADR control packet.
OBJECT-TYPE    
  DisplayString Size(0..64)  

jnxPPPoEServiceNameAciAriAction 1.3.6.1.4.1.2636.3.67.1.1.4.3.1.3
Identifies the behavior when the the Service-name with ACI/ARI pairs is received in a PADI frame.
OBJECT-TYPE    
  JnxPPPoEServiceNameAction  

jnxPPPoEServiceNameAciAriDynamicProfile 1.3.6.1.4.1.2636.3.67.1.1.4.3.1.4
Dynamic Profile associated with a Service-name and ACI/ARI pairs
OBJECT-TYPE    
  DisplayString  

jnxPPPoEServiceNameAciAriRoutingInstance 1.3.6.1.4.1.2636.3.67.1.1.4.3.1.5
Routing-Instance associated with a Service-name and ACI/ARI pairs
OBJECT-TYPE    
  DisplayString Size(0..31)  

jnxPPPoEServiceNameAciAriStaticInterface 1.3.6.1.4.1.2636.3.67.1.1.4.3.1.6
Static Interface associated with each ACI/ARI Entry.
OBJECT-TYPE    
  DisplayString  

jnxPPPoEServiceNameAciAriRowStatus 1.3.6.1.4.1.2636.3.67.1.1.4.3.1.7
Controls creation/deletion of entries in this table with READ-CREATE maximum access, according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPPPoEServiceNameAciAriRowStatus The ACIARI Entry is configured via the INDEX specified. The following values can be read from this object: active(1)
OBJECT-TYPE    
  RowStatus  

jnxPPPoEMajorInterfaceCount 1.3.6.1.4.1.2636.3.67.1.1.3.1
The total number of PPPoEmajor interfaces configured and created in the system.
OBJECT-TYPE    
  Integer32  

jnxPPPoESummaryMajorIfAdminUp 1.3.6.1.4.1.2636.3.67.1.1.3.2
The total number of PPPoEmajor interfaces in the system that are administratively configured to up(1).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummaryMajorIfAdminDown 1.3.6.1.4.1.2636.3.67.1.1.3.3
The total number of PPPoEmajor interfaces in the system that are administrateively configued to down(2).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummaryMajorIfOperUp 1.3.6.1.4.1.2636.3.67.1.1.3.4
The total number of PPPoEmajor interfaces in the system with an operational state of up(1).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummaryMajorIfOperDown 1.3.6.1.4.1.2636.3.67.1.1.3.5
The total number of PPPoEmajor interfaces in the system with an operational state of down(2).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummaryMajorIfLowerLayerDown 1.3.6.1.4.1.2636.3.67.1.1.3.6
The total number of PPPoEmajor interfaces in the system with an operational state of lowerLayerDown(7).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummaryMajorIfNotPresent 1.3.6.1.4.1.2636.3.67.1.1.3.7
The total number of PPPoEmajor interfaces in the system with an operational state of notPresent(6).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummarySubInterfaceCount 1.3.6.1.4.1.2636.3.67.1.1.3.8
The total number of PPPoEsubinterfaces configured in the system.
OBJECT-TYPE    
  Integer32  

jnxPPPoESummarySubIfAdminUp 1.3.6.1.4.1.2636.3.67.1.1.3.9
The total number of PPPoEsubinterfaces in the system that are administratively configured to up(1).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummarySubIfAdminDown 1.3.6.1.4.1.2636.3.67.1.1.3.10
The total number of PPPoEsubinterfaces in the system that are administrateively configued to down(2).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummarySubIfOperUp 1.3.6.1.4.1.2636.3.67.1.1.3.11
The total number of PPPoEsubinterfaces in the system with an operational state of up(1).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummarySubIfOperDown 1.3.6.1.4.1.2636.3.67.1.1.3.12
The total number of PPPoEsubinterfaces in the system with an operational state of down(2).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummarySubIfLowerLayerDown 1.3.6.1.4.1.2636.3.67.1.1.3.13
The total number of PPPoEsubinterfaces in the system with an operational state of lowerLayerDown(7).
OBJECT-TYPE    
  Integer32  

jnxPPPoESummarySubIfNotPresent 1.3.6.1.4.1.2636.3.67.1.1.3.14
The total number of PPPoEsubinterfaces in the system with an operational state of notPresent(6).
OBJECT-TYPE    
  Integer32  

jnxPPPoEConformance 1.3.6.1.4.1.2636.3.67.1.4
OBJECT IDENTIFIER    

jnxPPPoECompliances 1.3.6.1.4.1.2636.3.67.1.4.1
OBJECT IDENTIFIER    

jnxPPPoEGroups 1.3.6.1.4.1.2636.3.67.1.4.2
OBJECT IDENTIFIER