This specifies port speed in bits per second
speed300 : 300 bits per second
speed600 : 600 bits per second
speed1200 : 1200 bits per second
speed1800 : 1800 bits per second
speed2400 : 2400 bits per second
speed4800 : 4800 bits per second
speed7200 : 7200 bits per second
speed9600 : 9600 bits per second
speed19200 : 19200 bits per second .
This specifies the amount of time in 1/20th of a
second that the PAD waits for a response from a
controller. A value of 5 gives a response timeout
of 250ms.
This specifies the maximum amount of time in 1/20
of a second that the PAD waits between two characters
when receiving data from the attatched devices before
detecting a line problem. A value of 2 gives an
intercharacter timeout of 100ms.
This specifies the retry limit for polls/selects
sent, NAKs sent/received and ENQs sent/received.
In case of polls and selects, the controller is
placed in slow poll mode on reaching this limit.
This specifies the number of retries that will be
made immediately in case of response timeout on
Poll, response timeout on Select or NAK response
to select. The next controller in the list will be
polled/selected only after these many retries are
made for the non-responding controller.
All consecutive retries will be counted as one retry
attempt.
This specifies the mnemonic used by the PAD to
place calls to the Host for this controller.
Host initiated calls will be accepted only if
this field is blank.
This specifies the X.25 address inserted in the
calling address field of the call packet sent by
the PAD to the Host. This address identifies the
controller to the Host.
This controls whether billing(accounting) records
will be created for calls on this station
billingDisabled : billing is disabled
billingEnabled : billing is enabled .
This specifies port speed in bits per second
speed300 : 300 bits per second
speed600 : 600 bits per second
speed1200 : 1200 bits per second
speed1800 : 1800 bits per second
speed2400 : 2400 bits per second
speed4800 : 4800 bits per second
speed7200 : 7200 bits per second
speed9600 : 9600 bits per second
speed19200 : 19200 bits per second .
This indicates the line status :
up : if one or more controllers are responding
to polls
down : if no controllers are responding or garbage
is being received.
This indicates the current state of the station
up : when responding to polls
down : when tries have expired and controller
is in slow poll
suspended : when polling has been stopped by host
blocked : when polling has been stopped because
the X.25 channel is blocked
disabled : when station is disabled.
This gives information regarding the calls placed by this
station on its host.
calling : when it is waiting call accept from the host
connected : when the connection to the host has been
accepted
idle : when connection attempts are not in progress
(no data to send to the Host), or autocall
attempts have been exhausted or when it is
waiting for autocall timeout (to send call
request again).
This indicates the called address in the last
inbound call request packet sent by this station.
A value of 'Last Call Information not available'
will be returned if the last incoming call packet
is not present.
This indicates the calling address in the last
inbound request packet sent by this station.
A value of 'Last Call Information not available'
will be returned if the last incoming call packet
is not present.
This indicates the facilities in the last
inbound request packet sent by this station.
A value of 'Last Call Information not available'
will be returned if the last incoming call packet
is not present.
This indicates the data in the Call User Data field
in the last inbound call request packet sent by this
station. A value of 'Last Call Information not available'
will be returned if the incoming call packet is not
present.
This indicates the called address in the last
outbound call request packet sent by this station.
A value of 'Last Call Information not available'
will be returned if the last outgoing call packet
is not present.
This indicates the calling address in the last
outbound call request packet sent by this station.
A value of 'Last Call Information not available'
will be returned if the last outgoing call packet
is not present.
This indicates the facilities in the last
outbound call request packet sent by this station.
A value of 'Last Call Information not available'
will be returned if the last outgoing call packet
is not present.
This indicates the data in the Call User Data field
in the last outbound call request packet sent by
this station. A value of 'Last Call Information not
available' will be returned if the last call outgoing
packet is not present.
The 'Receive Window Closed' is incremented every
time the 3201 station removes data out of its queue
towards the terminal and the number of messages queued
is greater than 15.
This indicates the number of times the controller did not
respond to a ACK before response timeout and the number
of times the inter-character timer expired when receiving
response to a NAK.
