IPV4-OSPF-MIB

File: IPV4-OSPF-MIB.mib (13272 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC APENT-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
IpAddress RowStatus apIpv4Ospf

Defined Types

ApIpv4OspfAdvRouteEntry  
SEQUENCE    
  apIpv4OspfAdvRoutePrefix IpAddress
  apIpv4OspfAdvRoutePrefixLen INTEGER
  apIpv4OspfAdvRouteType INTEGER
  apIpv4OspfAdvRouteMetric INTEGER
  apIpv4OspfAdvRouteTag Integer32
  apIpv4OspfAdvRouteStatus RowStatus

ApIpv4OspfIfAdvRouteEntry  
SEQUENCE    
  apIpv4OspfIfAdvRouteAddress IpAddress
  apIpv4OspfIfAdvRoutePrefix IpAddress
  apIpv4OspfIfAdvRoutePrefixLen INTEGER
  apIpv4OspfIfAdvRouteType INTEGER
  apIpv4OspfIfAdvRouteMetric INTEGER
  apIpv4OspfIfAdvRouteTag Integer32
  apIpv4OspfIfAdvRouteStatus RowStatus

Defined Values

apIpv4OspfMib 1.3.6.1.4.1.2467.1.9.3.2.1
This MIB module describes the ArrowPoint enterprise MIB support for the Routing Information Protocol
MODULE-IDENTITY    

apIpv4OspfRedistributeLocal 1.3.6.1.4.1.2467.1.9.3.2.2
If enabled, local (direct) routes will be advertised by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

apIpv4OspfLocalType 1.3.6.1.4.1.2467.1.9.3.2.3
If local routes are advertised by OSPF, this is the ASE type to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER aseType1(1), aseType2(2)  

apIpv4OspfLocalMetric 1.3.6.1.4.1.2467.1.9.3.2.4
If local routes are advertised by OSPF, this is the metric to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16777215  

apIpv4OspfLocalTag 1.3.6.1.4.1.2467.1.9.3.2.5
If local routes are advertised by OSPF, this is the tag value to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apIpv4OspfRedistributeStatic 1.3.6.1.4.1.2467.1.9.3.2.6
If enabled, static routes will be advertised by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

apIpv4OspfStaticType 1.3.6.1.4.1.2467.1.9.3.2.7
If static routes are advertised by OSPF, this is the ASE type to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER aseType1(1), aseType2(2)  

apIpv4OspfStaticMetric 1.3.6.1.4.1.2467.1.9.3.2.8
If static routes are advertised by OSPF, this is the metric to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16777215  

apIpv4OspfStaticTag 1.3.6.1.4.1.2467.1.9.3.2.9
If static routes are advertised by OSPF, this is the tag value to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apIpv4OspfRedistributeRip 1.3.6.1.4.1.2467.1.9.3.2.10
If enabled, RIP routes will be advertised by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

apIpv4OspfRipType 1.3.6.1.4.1.2467.1.9.3.2.11
If RIP routes are advertised by OSPF, this is the ASE type to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER aseType1(1), aseType2(2)  

apIpv4OspfRipMetric 1.3.6.1.4.1.2467.1.9.3.2.12
If RIP routes are advertised by OSPF, this is the metric to use when advertising the routes. If zero is specified, the RIP metric will be used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16777215  

apIpv4OspfRipTag 1.3.6.1.4.1.2467.1.9.3.2.13
If RIP routes are advertised by OSPF, this is the tag value to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apIpv4OspfOriginateDefault 1.3.6.1.4.1.2467.1.9.3.2.14
If enabled, an ASE will be generated for the default route.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

apIpv4OspfDefaultType 1.3.6.1.4.1.2467.1.9.3.2.15
If a default ASE is originated by OSPF, this is the ASE type to use when advertising the route.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER aseType1(1), aseType2(2)  

apIpv4OspfDefaultMetric 1.3.6.1.4.1.2467.1.9.3.2.16
If a default ASE is originated by OSPF, this is the metric to use when advertising the route.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16777215  

apIpv4OspfDefaultTag 1.3.6.1.4.1.2467.1.9.3.2.17
If a default ASE is originated by OSPF, this is the tag value to use when advertising the route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apIpv4OspfRedistributeFirewall 1.3.6.1.4.1.2467.1.9.3.2.18
If enabled, firewall routes will be advertised by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

apIpv4OspfFirewallType 1.3.6.1.4.1.2467.1.9.3.2.19
If firewall routes are advertised by OSPF, this is the ASE type to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER aseType1(1), aseType2(2)  

apIpv4OspfFirewallMetric 1.3.6.1.4.1.2467.1.9.3.2.20
If firewall routes are advertised by OSPF, this is the metric to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16777215  

apIpv4OspfFirewallTag 1.3.6.1.4.1.2467.1.9.3.2.21
If firewall routes are advertised by OSPF, this is the tag value to use when advertising the routes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apIpv4OspfAdvRouteTable 1.3.6.1.4.1.2467.1.9.3.2.22
A list of routes that are advertised via all OSPF interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApIpv4OspfAdvRouteEntry

apIpv4OspfAdvRouteEntry 1.3.6.1.4.1.2467.1.9.3.2.22.1
A single route to advertise via all OSPF interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApIpv4OspfAdvRouteEntry  

apIpv4OspfAdvRoutePrefix 1.3.6.1.4.1.2467.1.9.3.2.22.1.1
The route prefix to be advertised.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apIpv4OspfAdvRoutePrefixLen 1.3.6.1.4.1.2467.1.9.3.2.22.1.2
The network prefix length associated with this route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..32  

apIpv4OspfAdvRouteType 1.3.6.1.4.1.2467.1.9.3.2.22.1.3
this is the ASE type to use when advertising this route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER aseType1(1), aseType2(2)  

apIpv4OspfAdvRouteMetric 1.3.6.1.4.1.2467.1.9.3.2.22.1.4
The metric to use when advertising this route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..16777215  

apIpv4OspfAdvRouteTag 1.3.6.1.4.1.2467.1.9.3.2.22.1.5
this is the tag value to use when advertising this route.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

apIpv4OspfAdvRouteStatus 1.3.6.1.4.1.2467.1.9.3.2.22.1.6
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

apIpv4OspfIfAdvRouteTable 1.3.6.1.4.1.2467.1.9.3.2.23
A list of routes that are advertised via a specific OSPF interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApIpv4OspfIfAdvRouteEntry

apIpv4OspfIfAdvRouteEntry 1.3.6.1.4.1.2467.1.9.3.2.23.1
A single route to advertise via a specific OSPF interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApIpv4OspfIfAdvRouteEntry  

apIpv4OspfIfAdvRouteAddress 1.3.6.1.4.1.2467.1.9.3.2.23.1.1
The address of the OSPF interface. If this is a valid unicast IP address, the interface is numbered. Otherwise, it indicates the ifIndex of an unnumbered interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apIpv4OspfIfAdvRoutePrefix 1.3.6.1.4.1.2467.1.9.3.2.23.1.2
The route prefix to be advertised.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apIpv4OspfIfAdvRoutePrefixLen 1.3.6.1.4.1.2467.1.9.3.2.23.1.3
The network prefix length associated with this route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..32  

apIpv4OspfIfAdvRouteType 1.3.6.1.4.1.2467.1.9.3.2.23.1.4
this is the ASE type to use when advertising this route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER aseType1(1), aseType2(2)  

apIpv4OspfIfAdvRouteMetric 1.3.6.1.4.1.2467.1.9.3.2.23.1.5
The metric to use when advertising this route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..16777215  

apIpv4OspfIfAdvRouteTag 1.3.6.1.4.1.2467.1.9.3.2.23.1.6
this is the tag value to use when advertising this route.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

apIpv4OspfIfAdvRouteStatus 1.3.6.1.4.1.2467.1.9.3.2.23.1.7
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

apIpv4OspfEqualCostRoutes 1.3.6.1.4.1.2467.1.9.3.2.24
The maximum number of equal-cost routes OSPF can use.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..15