IEEE8021-TEIPS-V2-MIB

File: IEEE8021-TEIPS-V2-MIB.mib (29300 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IEEE8021-TC-MIB
IEEE8021-BRIDGE-MIB SNMPv2-CONF

Imported symbols

MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE
Unsigned32 RowStatus StorageType
TruthValue ieee802dot1mibs IEEE8021BridgePortNumber
IEEE8021TeipsIpgConfigActiveRequests IEEE8021TeipsIpgid IEEE8021TeipsIpgConfigAdmin
IEEE8021PbbTeTSidId ieee8021BridgeBaseComponentId MODULE-COMPLIANCE
NOTIFICATION-GROUP OBJECT-GROUP

Defined Types

Ieee8021TeipsV2IpgEntry  
SEQUENCE    
  ieee8021TeipsV2Ipgid IEEE8021TeipsIpgid
  ieee8021TeipsV2IpgWorkingMA Unsigned32
  ieee8021TeipsV2IpgProtectionMA Unsigned32
  ieee8021TeipsV2IpgWorkingPortNumber IEEE8021BridgePortNumber
  ieee8021TeipsV2IpgProtectionPortNumber IEEE8021BridgePortNumber
  ieee8021TeipsV2IpgStorageType StorageType
  ieee8021TeipsV2IpgRowStatus RowStatus

Ieee8021TeipsV2TesiEntry  
SEQUENCE    
  ieee8021TeipsV2TesiIndex Unsigned32
  ieee8021TeipsV2TesiId IEEE8021PbbTeTSidId
  ieee8021TeipsV2TesiStorageType StorageType
  ieee8021TeipsV2TesiRowStatus RowStatus

Ieee8021TeipsV2CandidatePsEntry  
SEQUENCE    
  ieee8021TeipsV2CandidatePsIndex Unsigned32
  ieee8021TeipsV2CandidatePsMA Unsigned32
  ieee8021TeipsV2CandidatePsPort IEEE8021BridgePortNumber
  ieee8021TeipsV2CandidatePsOper TruthValue
  ieee8021TeipsV2CandidatePsStorageType StorageType
  ieee8021TeipsV2CandidatePsRowStatus RowStatus

Ieee8021TeipsV2IpgConfigEntry  
SEQUENCE    
  ieee8021TeipsV2IpgConfigState INTEGER
  ieee8021TeipsV2IpgConfigCommandStatus IEEE8021TeipsIpgConfigAdmin
  ieee8021TeipsV2IpgConfigCommandLast IEEE8021TeipsIpgConfigAdmin
  ieee8021TeipsV2IpgConfigCommandAdmin IEEE8021TeipsIpgConfigAdmin
  ieee8021TeipsV2IpgConfigActiveRequests IEEE8021TeipsIpgConfigActiveRequests
  ieee8021TeipsV2IpgConfigWTR Unsigned32
  ieee8021TeipsV2IpgConfigHoldOff Unsigned32
  ieee8021TeipsV2IpgM1ConfigState INTEGER
  ieee8021TeipsV2IpgConfigMWTR Unsigned32
  ieee8021TeipsV2IpgConfigNotifyEnable TruthValue
  ieee8021TeipsV2IpgConfigStorageType StorageType

Defined Values

ieee8021TeipsV2Mib 1.3.111.2.802.1.1.27
Copyright (C) IEEE. All Rights Reserved This MIB module is part of IEEE 802.1Q; See the IEEE 802.1Q standard for full legal notices. Unless otherwise indicated, the references in this MIB module are to IEEE Std 802.1Q-2014
MODULE-IDENTITY    

ieee8021TeipsV2Notifications 1.3.111.2.802.1.1.27.0
OBJECT IDENTIFIER    

ieee8021TeipsV2Objects 1.3.111.2.802.1.1.27.1
OBJECT IDENTIFIER    

ieee8021TeipsV2Conformance 1.3.111.2.802.1.1.27.2
OBJECT IDENTIFIER    

ieee8021TeipsV2IpgTable 1.3.111.2.802.1.1.27.1.1
The IPG table. Each entry in this table corresponds to an Infrastructure Protection Group (IPG) associated with a PBB supporting Infrastructure Protection Switching (IPS).
OBJECT-TYPE    
  SEQUENCE OF  
    Ieee8021TeipsV2IpgEntry

ieee8021TeipsV2IpgEntry 1.3.111.2.802.1.1.27.1.1.1
The IPG table entry.
OBJECT-TYPE    
  Ieee8021TeipsV2IpgEntry  

ieee8021TeipsV2Ipgid 1.3.111.2.802.1.1.27.1.1.1.1
Uniquely identifies an IPG within the PBB.
OBJECT-TYPE    
  IEEE8021TeipsIpgid  

ieee8021TeipsV2IpgWorkingMA 1.3.111.2.802.1.1.27.1.1.1.2
Identifies the Segment MA that corresponds to the IPG's working entity. The MA index in this column must hold a value that is the value of dot1agCfmStackMaIndex column for some entry in the dot1agCfmStackTable before the RowStatus for this row can be set to Active. Furthermore, this column may not be modified when the RowStatus for this row is Active.
OBJECT-TYPE    
  Unsigned32  

ieee8021TeipsV2IpgProtectionMA 1.3.111.2.802.1.1.27.1.1.1.3
Identifies the Segment MA that corresponds to the IPG's protection entity. The MA index in this column must hold a value that is the value of dot1agCfmStackMaIndex column for some entry in the dot1agCfmStackTable before the RowStatus for this row can be set to Active. Furthermore, this column may not be modified when the RowStatus for this row is Active.
OBJECT-TYPE    
  Unsigned32  

ieee8021TeipsV2IpgWorkingPortNumber 1.3.111.2.802.1.1.27.1.1.1.4
Identifies the local Port associated with the IPG Working Segment.
OBJECT-TYPE    
  IEEE8021BridgePortNumber  

ieee8021TeipsV2IpgProtectionPortNumber 1.3.111.2.802.1.1.27.1.1.1.5
Identifies the local Port associated with the IPG Protection Segment.
OBJECT-TYPE    
  IEEE8021BridgePortNumber  

ieee8021TeipsV2IpgStorageType 1.3.111.2.802.1.1.27.1.1.1.6
This object indicates the persistence of this entry. All read-create columns must be writable if this column is set to permanent.
OBJECT-TYPE    
  StorageType  

ieee8021TeipsV2IpgRowStatus 1.3.111.2.802.1.1.27.1.1.1.7
The status of this row. The writable columns in a row cannot be changed if the row is active. The TeipsIpgWorkingMA and TeipsIpgProtectionMA columns must be specified before the row can be activated.
OBJECT-TYPE    
  RowStatus  

ieee8021TeipsV2TesiTable 1.3.111.2.802.1.1.27.1.2
The IPG TE-SID table contains identifies the TE service instances associated with an IPG.
OBJECT-TYPE    
  SEQUENCE OF  
    Ieee8021TeipsV2TesiEntry

ieee8021TeipsV2TesiEntry 1.3.111.2.802.1.1.27.1.2.1
The TE-IPS TESI entry. Each entry identifies a TESI associated with an IPG.
OBJECT-TYPE    
  Ieee8021TeipsV2TesiEntry  

ieee8021TeipsV2TesiIndex 1.3.111.2.802.1.1.27.1.2.1.1
This is an identifier, of local signifigance to a particular PBB-TE TE-SID associated with an IPG.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ieee8021TeipsV2TesiId 1.3.111.2.802.1.1.27.1.2.1.2
This column holds the TESI identifier corresponding to a TE service instance associated with an IPG.
OBJECT-TYPE    
  IEEE8021PbbTeTSidId  

ieee8021TeipsV2TesiStorageType 1.3.111.2.802.1.1.27.1.2.1.3
This object indicates the persistence of this entry. All read-create columns must be writable for permanent rows.
OBJECT-TYPE    
  StorageType  

ieee8021TeipsV2TesiRowStatus 1.3.111.2.802.1.1.27.1.2.1.4
This column holds the status for this row. When the status is active, no columns of this table may be modified. All columns must have a valid value before the row can be activated.
OBJECT-TYPE    
  RowStatus  

ieee8021TeipsV2CandidatePsTable 1.3.111.2.802.1.1.27.1.3
The Candidate PS table lists, in priority order, from highest priority to lowest priority, the Maintenance Associations corresponding to candidate Protection Segments associated with an IPG.
OBJECT-TYPE    
  SEQUENCE OF  
    Ieee8021TeipsV2CandidatePsEntry

ieee8021TeipsV2CandidatePsEntry 1.3.111.2.802.1.1.27.1.3.1
A Candidate PS entry. Each entry identifies a candidate Protection Segment associated with an IPG.
OBJECT-TYPE    
  Ieee8021TeipsV2CandidatePsEntry  

ieee8021TeipsV2CandidatePsIndex 1.3.111.2.802.1.1.27.1.3.1.1
This is an identifier, of local signifigance to a particular candidate Protection Segment associated with an IPG.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ieee8021TeipsV2CandidatePsMA 1.3.111.2.802.1.1.27.1.3.1.2
This column holds the candidate Protection Segment MA corresponding to a candidate Protection Segment associated with an IPG.
OBJECT-TYPE    
  Unsigned32  

ieee8021TeipsV2CandidatePsPort 1.3.111.2.802.1.1.27.1.3.1.3
This column holds the Port Number corresponding to the candidate Protection Segment associated with an IPG.
OBJECT-TYPE    
  IEEE8021BridgePortNumber  

ieee8021TeipsV2CandidatePsOper 1.3.111.2.802.1.1.27.1.3.1.4
This column indicates whether or not the candidate Protection Segment is operational.
OBJECT-TYPE    
  TruthValue  

ieee8021TeipsV2CandidatePsStorageType 1.3.111.2.802.1.1.27.1.3.1.5
This object indicates the persistence of this entry. All read-create columns must be writable for permanent rows.
OBJECT-TYPE    
  StorageType  

ieee8021TeipsV2CandidatePsRowStatus 1.3.111.2.802.1.1.27.1.3.1.6
This column holds the status for this row. When the status is active, no columns of this table may be modified. All columns must have a valid value before the row can be activated.
OBJECT-TYPE    
  RowStatus  

ieee8021TeipsV2IpgConfigTable 1.3.111.2.802.1.1.27.1.4
The PBB-TE IPS IPG config table contains configuration and status information for each IPG configured in the system. Entries in this table are created implicitly by the creation of entries in the ieee8021TeipsV2IpgTable.
OBJECT-TYPE    
  SEQUENCE OF  
    Ieee8021TeipsV2IpgConfigEntry

ieee8021TeipsV2IpgConfigEntry 1.3.111.2.802.1.1.27.1.4.1
The IPG confguration table entry. Rows are created in this table implicitly when a row is added to the ieee8021TeipsV2IpgTable.
OBJECT-TYPE    
  Ieee8021TeipsV2IpgConfigEntry  

ieee8021TeipsV2IpgConfigState 1.3.111.2.802.1.1.27.1.4.1.1
This column indicates the current state of the protection switching state machine for an IPG. The value can be one of the following: workingSegment(1) The protection switching state machine is in the WORKING_PATH state. protectionSegment(2) The protection switching state machine is in the PROTECTION_PATH state. waitToRestore(3) The protection switching state machine is in the WTR state. protAdmin(4) The protection switching state machine is in the PROT_ADMIN state.
OBJECT-TYPE    
  INTEGER workingSegment(1), protectionSegment(2), waitToRestore(3), protAdmin(4)  

ieee8021TeipsV2IpgConfigCommandStatus 1.3.111.2.802.1.1.27.1.4.1.2
This column indicates the status of administrative commands within the protection group. It reflects the current operational administrative command being acted upon by the IPG.
OBJECT-TYPE    
  IEEE8021TeipsIpgConfigAdmin  

ieee8021TeipsV2IpgConfigCommandLast 1.3.111.2.802.1.1.27.1.4.1.3
This column indicates the last attempted administrative command applied to the IPG. It is changed whenever a write is made to the CommandAdmin column of this table and is essentially record of the last attempted administrative operation.
OBJECT-TYPE    
  IEEE8021TeipsIpgConfigAdmin  

ieee8021TeipsV2IpgConfigCommandAdmin 1.3.111.2.802.1.1.27.1.4.1.4
This column is used by the operator to request that the IPG state machine perform some administrative operation. The operator requests a command by writing the command value to this column. The state machine indicates the command that it is performing by setting the value of the CommandStatus column of this table. This column always reads back as clear(1).
OBJECT-TYPE    
  IEEE8021TeipsIpgConfigAdmin  

ieee8021TeipsV2IpgConfigActiveRequests 1.3.111.2.802.1.1.27.1.4.1.5
This column shows the status of active requests associated with the IPG.
OBJECT-TYPE    
  IEEE8021TeipsIpgConfigActiveRequests  

ieee8021TeipsV2IpgConfigWTR 1.3.111.2.802.1.1.27.1.4.1.6
This column is used to configure the wait-to-restore timer for the IPG operation. The timer may be configured in steps of 1 minute between 5 and 12 minutes, the default being 5. Additionally, the value 0 is used to indicate that the IPG is to operate non-revertively. The value 0 is not permitted if the IPG is configured for M:1 IPS operation.
OBJECT-TYPE    
  Unsigned32 0 | 5..12  

ieee8021TeipsV2IpgConfigHoldOff 1.3.111.2.802.1.1.27.1.4.1.7
This column is used to configure the hold off timer. The purpose is to allow IPS to fix the problem before a higher-layer mechanism, such as PBB-TE TESI protection, is invoked or to allow an inner IPG to fix the problem before IPS is invoked by the outer IPG when IPGs are nested. The hold off timer has a period of from 0 to 10 seconds, the default being 0, with a 100ms granularity.
OBJECT-TYPE    
  Unsigned32 0..100  

ieee8021TeipsV2IpgM1ConfigState 1.3.111.2.802.1.1.27.1.4.1.8
This column indicates the current state of the M:1 protection switching state machine for an IPG if M:1 IPS is supported. The value can be one of the following: psAssigned(1) The protection switching state machine is in the PS_ASSIGNED state. segmentOk(2) The protection switching state machine is in the SEGMENT_OK state. segmentFailed(3) The protection switching state machine is in the SEGMENT_FAILED state. assignNewPs(4) The protection switching state machine is in the ASSIGN_NEW_PS state. revertToBetterPs(5) The protection switching state machine is in the REVERT_T0_BETTER_PS state.
OBJECT-TYPE    
  INTEGER psAssigned(1), segmentOk(2), segmentFailed(3), assignNewPs(4), revertToBetterPs(5)  

ieee8021TeipsV2IpgConfigMWTR 1.3.111.2.802.1.1.27.1.4.1.9
This column is used to configure the M:1 wait-to-restore timer for the IPG operation if M:1 protection is supported. The timer may be configured in steps of 1 minute between 5 and 12 minutes, the default being 5. Additionally, the value 0 is used to indicate that the IPG is to operate non-revertively.
OBJECT-TYPE    
  Unsigned32 0 | 5..12  

ieee8021TeipsV2IpgConfigNotifyEnable 1.3.111.2.802.1.1.27.1.4.1.10
This column is used to enable or disable transmission of ieee8021TeipsV2IpgAdminFailure notifications. These notifications are generated whenever an administrative command cannot be performed by the IPG.
OBJECT-TYPE    
  TruthValue  

ieee8021TeipsV2IpgConfigStorageType 1.3.111.2.802.1.1.27.1.4.1.11
This object indicates the persistence of this entry. For permanent objects the ieee8021TeipsV2IpgConfigCommandAdmin column must be writable.
OBJECT-TYPE    
  StorageType  

ieee8021TeipsV2IpgAdminFailure 1.3.111.2.802.1.1.27.0.1
An IPG generates this notification whenever an adminisistrative command cannot be executed by the IPS state machine. For example, when a requested manual switch cannot be performed because of a signal failure condition. The management entity receiving the notification can identify the system from the network source address of the notification and can identify the IPG by the indices of the OID of the ieee8021TeipsV2IpgConfigState variable in the notification: ieee8021BridgeBaseComponentId - Identifies the component on the Bridge where the protection group is configured. ieee8021TeipsV2Ipgid - The ID of the protection group.
NOTIFICATION-TYPE    

ieee8021TeipsV2Compliances 1.3.111.2.802.1.1.27.2.1
OBJECT IDENTIFIER    

ieee8021TeipsV2Groups 1.3.111.2.802.1.1.27.2.2
OBJECT IDENTIFIER    

ieee8021TeipsV2IpgGroup 1.3.111.2.802.1.1.27.2.2.1
Objects for the IPG group.
OBJECT-GROUP    

ieee8021TeipsV2CandidatePsGroup 1.3.111.2.802.1.1.27.2.2.2
Objects for the Candidate PS group.
OBJECT-GROUP    

ieee8021TeipsV2IpgTesiGroup 1.3.111.2.802.1.1.27.2.2.3
Objects for the IPG Tuple group.
OBJECT-GROUP    

ieee8021TeipsV2IpgConfigManGroup 1.3.111.2.802.1.1.27.2.2.4
Mandatory objects for the TeipsConfiguration group.
OBJECT-GROUP    

ieee8021TeipsV2IpgConfigOptGroup 1.3.111.2.802.1.1.27.2.2.5
Optional 0bjects for the TeipsConfiguration group.
OBJECT-GROUP    

ieee8021TeipsV2NotificationsGroup 1.3.111.2.802.1.1.27.2.2.6
Objects for the notifications group.
NOTIFICATION-GROUP    

ieee8021TeipsV2Compliance 1.3.111.2.802.1.1.27.2.1.1
The compliance statement for support of the TEIPS MIB module.
MODULE-COMPLIANCE