HUAWEI-VO-DIAL-CONTROL-MIB

File: HUAWEI-VO-DIAL-CONTROL-MIB.mib (36036 bytes)

Imported modules

SNMPv2-SMI HUAWEI-3COM-OID-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY IpAddress
voice

Defined Types

EntryStatus  
INTEGER valid(1), createRequest(2), underCreation(3), invalid(4)    

HWVoPeerCommonConfigEntry  
SEQUENCE    
  hwVoPeerConfigIndex INTEGER
  hwVoPeerConfigType INTEGER
  hwVoPeerConfigDesPattern OCTET STRING
  hwVoPeerConfigCodec1st INTEGER
  hwVoPeerConfigCodec2st INTEGER
  hwVoPeerConfigCodec3st INTEGER
  hwVoPeerConfigCodec4st INTEGER
  hwVoPeerConfigIpPreced INTEGER
  hwVoPeerConfigShutDown INTEGER
  hwVoPeerConfigVADSwitch INTEGER
  hwVoPeerConfigDtmfRelay INTEGER
  hwVoPeerConfigFaxLevel INTEGER
  hwVoPeerConfigFaxRate INTEGER
  hwVoPeerConfigFaxLocalTrainParam INTEGER
  hwVoPeerConfigFaxProtocol INTEGER
  hwVoPeerConfigFaxT38HighRedunPackNumber INTEGER
  hwVoPeerConfigFaxT38LowRedunPackNumber INTEGER
  hwVoPeerConfigFaxSendNSFSwitch INTEGER
  hwVoPeerConfigFaxSupportMode INTEGER
  hwVoPeerConfigFaxTrainMode INTEGER
  hwVoPeerConfigFaxRelay INTEGER
  hwVoPeerConfigRowStatus EntryStatus
  hwVoPeerConfigFaxPassthroughMode INTEGER
  hwVoPeerConfigPriority INTEGER
  hwVoPeerConfigAuthorizationLevel INTEGER
  hwVoPeerConfigDescription OCTET STRING
  hwVoPeerConfigCallingNumberType INTEGER
  hwVoPeerConfigCalledNumberType INTEGER
  hwVoPeerConfigCallingNumberingPlan INTEGER
  hwVoPeerConfigCalledNumberingPlan INTEGER
  hwVoPeerConfigSelectStop INTEGER
  hwVoPeerConfigCallingNumSubstRule INTEGER
  hwVoPeerConfigCalledNumSubstRule INTEGER
  hwVoPeerConfigMaxCall INTEGER

HWVoPOTSPeerConfigEntry  
SEQUENCE    
  hwVoPOTSPeerConfigIndex INTEGER
  hwVoPOTSPeerConfigCancelTruncateEnable INTEGER
  hwVoPOTSPeerConfigPrefix OCTET STRING
  hwVoPOTSPeerConfigPort OCTET STRING
  hwVoPOTSPeerConfigSendNumber INTEGER

HWVoVoIPPeerConfigEntry  
SEQUENCE    
  hwVoVoIPPeerConfigIndex INTEGER
  hwVoVoIPPeerConfigSessionTargetType INTEGER
  hwVoVoIPPeerConfigSessionTarget IpAddress
  hwVoVoIPPeerConfigFastSwitch INTEGER
  hwVoVoIPPeerConfigTunnelSwitch INTEGER
  hwVoVoIPPeerConfigTeachPrefix OCTET STRING
  hwVoVoIPPeerConfigSendRing INTEGER

HWVoPeerConfigCallerPermitNumEntry  
SEQUENCE    
  hwVoPeerConfigCallerPermitNum OCTET STRING
  hwVoPeerConfigCallerPermitNumRowStatus EntryStatus

Defined Values

hwVoiceDialControlMIB 2.5
MODULE-IDENTITY    

hwVoPeerObjects 2.5.1
OBJECT IDENTIFIER    

hwVoPeerCommonConfigTable 2.5.1.1
The table contains the voice peer common information .
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWVoPeerCommonConfigEntry

hwVoPeerCommonConfigEntry 2.5.1.1.1
The common informatioin of voice peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWVoPeerCommonConfigEntry  

hwVoPeerConfigIndex 2.5.1.1.1.1
Index of voice peer common table. It identify the number of the voice peer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

hwVoPeerConfigType 2.5.1.1.1.2
Specify the type of voice peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pots(1), voip(2), vofr(3)  

hwVoPeerConfigDesPattern 2.5.1.1.1.3
The number associated with this voice peer.Character include '0' to '9','*','#','+','.','T' can be configured in this number.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

hwVoPeerConfigCodec1st 2.5.1.1.1.4
This object expresses the first desirable codec of speech for the peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g711a(1), g711u(2), g723r53(3), g723r63(4), g729(5), g729a(6), default(7)  

hwVoPeerConfigCodec2st 2.5.1.1.1.5
This object expresses the second desirable codec of speech for the peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g711a(1), g711u(2), g723r53(3), g723r63(4), g729(5), g729a(6), default(7)  

hwVoPeerConfigCodec3st 2.5.1.1.1.6
This object expresses the third desirable codec of speech for the peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g711a(1), g711u(2), g723r53(3), g723r63(4), g729(5), g729a(6), default(7)  

hwVoPeerConfigCodec4st 2.5.1.1.1.7
This object expresses the forth desirable codec with of speech for the peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g711a(1), g711u(2), g723r53(3), g723r63(4), g729(5), g729a(6), default(7)  

hwVoPeerConfigIpPreced 2.5.1.1.1.8
This object expresses the ip precedence of voice packets. The default value is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

hwVoPeerConfigShutDown 2.5.1.1.1.9
This object expresses the current status of the peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPeerConfigVADSwitch 2.5.1.1.1.10
Enable or disable the VAD (Voice Activity Detection).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPeerConfigDtmfRelay 2.5.1.1.1.11
set the DTMF relay type in this dial-peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER h245Alphanumeric(1), voice(2), sip(12)  

hwVoPeerConfigFaxLevel 2.5.1.1.1.12
This object expresses the fax level in this dial-peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 3..60  

hwVoPeerConfigFaxRate 2.5.1.1.1.13
This object expresses the fax transmit rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER r14400(1), r2400(2), r4800(3), r9600(4), disable(5), voice(6)  

hwVoPeerConfigFaxLocalTrainParam 2.5.1.1.1.14
This object expresses the fax local train threshold in this dial-peer. The default value is 10.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

hwVoPeerConfigFaxProtocol 2.5.1.1.1.15
This object expresses the fax protocol which this dial-peer support. The default value is t38.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nonstandard-compatible(1), t38(2), pcm(3), sip-t38(4), h323-t38(5)  

hwVoPeerConfigFaxT38HighRedunPackNumber 2.5.1.1.1.16
This object expresses the high speed redundancy packet numbers when t38 fax protocol is used for this dial-peer .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2  

hwVoPeerConfigFaxT38LowRedunPackNumber 2.5.1.1.1.17
This object expresses the low speed redundancy packet numbers when t38 fax protocol is used for this dial-peer .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..5  

hwVoPeerConfigFaxSendNSFSwitch 2.5.1.1.1.18
This object expresses whether or not send nsf to fax in this dial-peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPeerConfigFaxSupportMode 2.5.1.1.1.19
This object expresses the fax support mode in this dial-peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rtp(1), vt(2), sip-udp(4)  

hwVoPeerConfigFaxTrainMode 2.5.1.1.1.20
This object expresses the fax train mode in this dial-peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local(1), ppp(2)  

hwVoPeerConfigFaxRelay 2.5.1.1.1.21
This object expresses ecm mode is used in fax transmit or not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ecm(1), noecm(2)  

hwVoPeerConfigRowStatus 2.5.1.1.1.22
This object specifies the status of this conceptual row, which is used to create a new row or modify or delete an existing row in this table.
Status: current Access: read-write
OBJECT-TYPE    
  EntryStatus  

hwVoPeerConfigFaxPassthroughMode 2.5.1.1.1.23
set pcm fax protocol passthrough mode It is valid only when fax protocol is pcm .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g711alaw(1), g711ulaw(3), unknown(0)  

hwVoPeerConfigPriority 2.5.1.1.1.24
This object specifies the priority of this voice entity. It is between 0 and 10. The highest priority is 0, the lowest priority is 10, and 0 is the default value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..10  

hwVoPeerConfigAuthorizationLevel 2.5.1.1.1.25
This object specifies the caller level for local authorization. The level is between 0 and 9. The highest level is 9, the lowest level is 0, and 0 is the default value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..9  

hwVoPeerConfigDescription 2.5.1.1.1.26
This object specifies the textual description of this voice entity.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

hwVoPeerConfigCallingNumberType 2.5.1.1.1.27
This object specifies the numbering type of calling number about this voice entity. abbreviated - the numbering type is abbreviated. international - the numbering type is international. national - the numbering type is national. network - the numbering type is network. reserved - the numbering type is reserved. subscriber - the numbering type is subscriber. unknown - the numbering type is unkown.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER abbreviated(1), international(2), national(3), network(4), reserved(5), subscriber(6), unknown(7)  

hwVoPeerConfigCalledNumberType 2.5.1.1.1.28
This object specifies the numbering type of called number about this voice entity. abbreviated - the numbering type is abbreviated. international - the numbering type is international. national - the numbering type is national. network - the numbering type is network. reserved - the numbering type is reserved. subscriber - the numbering type is subscriber. unknown - the numbering type is unkown.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER abbreviated(1), international(2), national(3), network(4), reserved(5), subscriber(6), unknown(7)  

hwVoPeerConfigCallingNumberingPlan 2.5.1.1.1.29
This object specifies the numbering plan of calling number about this voice entity. data - data numbering plan. isdn - ISDN/telephone numbering plan. national - national standard numbering plan. private - Private numbering plan. reserved - Reserved for extension. telex - telex numbering plan. unknown - unknown.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER data(1), isdn(2), national(3), private(4), reserved(5), telex(6), unknown(7)  

hwVoPeerConfigCalledNumberingPlan 2.5.1.1.1.30
This object specifies the numbering plan of called number about this voice entity. data - data numbering plan. isdn - ISDN/telephone numbering plan. national - national standard numbering plan. private - Private numbering plan. reserved - Reserved for extension. telex - telex numbering plan. unknown - unknown.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER data(1), isdn(2), national(3), private(4), reserved(5), telex(6), unknown(7)  

hwVoPeerConfigSelectStop 2.5.1.1.1.31
This object specifies no further entity searching allowed if a call started on the this voice entity.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hwVoPeerConfigCallingNumSubstRule 2.5.1.1.1.32
This object specifies number-substitute rule that apply calling number of this voice entity. It is valid if its value is between 1 and 2147483647. This voice entity doesn't apply any number-substitute rule if its value is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

hwVoPeerConfigCalledNumSubstRule 2.5.1.1.1.33
This object specifies number-substitute rule that apply called number of this voice entity. It is valid if its value is between 1 and 2147483647. This voice entity doesn't apply any number-substitute rule if its value is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

hwVoPeerConfigMaxCall 2.5.1.1.1.34
The object specifies that this voice entity is bound with a tag that indicates a maximum call value. The value of 0 specifies that cancel the act of binding.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

hwVoPOTSPeerConfigTable 2.5.1.2
The table contains the pots peer information .
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWVoPOTSPeerConfigEntry

hwVoPOTSPeerConfigEntry 2.5.1.2.1
Pots peer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWVoPOTSPeerConfigEntry  

hwVoPOTSPeerConfigIndex 2.5.1.2.1.1
Index of voice pots peer table. It identify the number of the voice pots peer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

hwVoPOTSPeerConfigCancelTruncateEnable 2.5.1.2.1.2
Cancel truncate the called number in this dial-peer.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPOTSPeerConfigPrefix 2.5.1.2.1.3
This object expresses the pattern to be added before the dialed number. Valid character include '0' to '9' and ','.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

hwVoPOTSPeerConfigPort 2.5.1.2.1.4
set the voice port and group associated with this peer.The port number is seperated with group number by ':'.As analog voice port,the group number can be represented by 255.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..6)  

hwVoPOTSPeerConfigSendNumber 2.5.1.2.1.5
This object specifies the number digits to send to the destination. It can take the value: 0-31 number of right-justified digits of the match-template to be sent. -1 Truncate the called number(default). -2 send all match-template digits.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -2..31  

hwVoVoIPPeerConfigTable 2.5.1.3
The table contains the voip peer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWVoVoIPPeerConfigEntry

hwVoVoIPPeerConfigEntry 2.5.1.3.1
Voip peer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWVoVoIPPeerConfigEntry  

hwVoVoIPPeerConfigIndex 2.5.1.3.1.1
Index of voice voip peer table. It identify the number of the voip voice peer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

hwVoVoIPPeerConfigSessionTargetType 2.5.1.3.1.2
This object expresses the type of the session target for this peer .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ipv4(1), ras(2), unknown(3)  

hwVoVoIPPeerConfigSessionTarget 2.5.1.3.1.3
This object expresses the ip address IPV4 peer.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwVoVoIPPeerConfigFastSwitch 2.5.1.3.1.4
This object expresses whether or not the fast connect function enable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoVoIPPeerConfigTunnelSwitch 2.5.1.3.1.5
This object expresses whether or not the tunnel function enable. It cannot be used when no fast connect .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoVoIPPeerConfigTeachPrefix 2.5.1.3.1.6
This object expresses the technology prefix. Valid charater include '0' to '9', '#'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

hwVoVoIPPeerConfigSendRing 2.5.1.3.1.7
enable/disable the send ring. It is valid only when fast connect is enabled .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPeerDefaultConfigObjects 2.5.1.4
OBJECT IDENTIFIER    

hwVoPeerDefaultConfigCancelTrun 2.5.1.4.1
The default value of dial peer's Cancel trun
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPeerDefaultConfig1STCodecLevel 2.5.1.4.2
The default value of voice entity 1st codec level priority g711alaw G.711 A Law 64000 bps g711ulaw G.711 U Law 64000 bps g723r53 G.723.1 5300 bps g723r63 G.723.1 6300 bps g729r8 G.729 8000 bps g729a G.729 A
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g729r8(0), g711alaw(1), g723r63(2), g723r53(3), g711ulaw(4), g729a(5)  

hwVoPeerDefaultConfig2NDCodecLevel 2.5.1.4.3
The default value of voice entity 2nd codec level priority g711alaw G.711 A Law 64000 bps g711ulaw G.711 U Law 64000 bps g723r53 G.723.1 5300 bps g723r63 G.723.1 6300 bps g729r8 G.729 8000 bps g729a G.729 A
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g729r8(0), g711alaw(1), g723r63(2), g723r53(3), g711ulaw(4), g729a(5)  

hwVoPeerDefaultConfig3RDCodecLevel 2.5.1.4.4
The default value of voice entity 3rd codec level priority g711alaw G.711 A Law 64000 bps g711ulaw G.711 U Law 64000 bps g723r53 G.723.1 5300 bps g723r63 G.723.1 6300 bps g729r8 G.729 8000 bps g729a G.729 A
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g729r8(0), g711alaw(1), g723r63(2), g723r53(3), g711ulaw(4), g729a(5)  

hwVoPeerDefaultConfig4THCodecLevel 2.5.1.4.5
The default value of voice entity 4th codec level priority g711alaw G.711 A Law 64000 bps g711ulaw G.711 U Law 64000 bps g723r53 G.723.1 5300 bps g723r63 G.723.1 6300 bps g729r8 G.729 8000 bps g729a G.729 A
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g729r8(0), g711alaw(1), g723r63(2), g723r53(3), g711ulaw(4), g729a(5)  

hwVoPeerDefaultConfigVADOn 2.5.1.4.6
The default value of dial peer's VAD Switch
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPeerDefaultConfigFaxTransmitLevel 2.5.1.4.7
The default value of dial peer's FaxTransmitLevel.The unit is db
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 3..60  

hwVoPeerDefaultConfigFaxLocalTrain 2.5.1.4.8
The default value of dial peer's Fax local train threshold .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

hwVoPeerDefaultConfigFaxProtocol 2.5.1.4.9
The default value of dial peer's Fax Protocol .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nonstandard-compatible(1), t38(2), h323-t38(3), sip-t38(4), pcm-alaw(5), pcm-ulaw(6)  

hwVoPeerDefaultConfigFaxHSRedundancy 2.5.1.4.10
The default value of dial peer's T38 Fax Protocol High Redundancy.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2  

hwVoPeerDefaultConfigFaxLSRedundancy 2.5.1.4.11
The default value of dial peer's T38 Fax Protocol Low Redundancy.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2  

hwVoPeerDefaultConfigFaxBaudrate 2.5.1.4.12
The default value of dial peer's Fax Baudrate .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), b2400(2), b4800(3), b9600(5), b14400(7), voice(8)  

hwVoPeerDefaultConfigFaxNSF 2.5.1.4.13
The default value of fax non-standard faculty .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPeerDefaultConfigFaxSupportMode 2.5.1.4.14
The default value of fax SupportMode .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rtp(1), vt(2)  

hwVoPeerDefaultConfigFaxTrainMode 2.5.1.4.15
The default value of fax TrainMode .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ppp(1), local(2)  

hwVoPeerDefaultConfigFaxECM 2.5.1.4.16
The default value of fax ECM Mode .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVoPeerConfigCallerPermitNumTable 2.5.1.5
The table contains caller number permitted information in the specific voice entity for incoming call.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWVoPeerConfigCallerPermitNumEntry

hwVoPeerConfigCallerPermitNumEntry 2.5.1.5.1
A single caller number permitted in the specific voice entity for incoming call. The entry is created when its associated voPeerCommonCfgEntry is created. This entry is deleted when its associated voPeerCommonCfgEntry is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWVoPeerConfigCallerPermitNumEntry  

hwVoPeerConfigCallerPermitNum 2.5.1.5.1.1
This object specifies caller number permitted that must be of the form ^(([0-9ABCD#*.!+%[]()\-]+($)!)|($))$. Specially set this object $ meaning allow caller null.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..31)  

hwVoPeerConfigCallerPermitNumRowStatus 2.5.1.5.1.2
This object is used to create a new row or modify or delete an existing row in this table.
Status: current Access: read-write
OBJECT-TYPE    
  EntryStatus