HUAWEI-PORT-MIB

File: HUAWEI-PORT-MIB.mib (304482 bytes)

Imported modules

P-BRIDGE-MIB IF-MIB HUAWEI-IMA-MIB
SNMPv2-SMI SNMPv2-TC HUAWEI-MIB
SNMPv2-CONF

Imported symbols

EnabledStatus InterfaceIndex ImaFrameLength
ImaGroupState MODULE-IDENTITY OBJECT-TYPE
NOTIFICATION-TYPE Integer32 Unsigned32
Counter64 IpAddress TruthValue
RowStatus TEXTUAL-CONVENTION hwDatacomm
NOTIFICATION-GROUP OBJECT-GROUP MODULE-COMPLIANCE
DateAndTime

Defined Types

HwEthernetEntry  
SEQUENCE    
  hwEthernetIfIndex InterfaceIndex
  hwEthernetLoopback INTEGER
  hwEthernetPortType INTEGER
  hwEthernetSpeedSet INTEGER
  hwEthernetDuplex INTEGER
  hwEthernetNegotiation EnabledStatus
  hwEthernetPortTypeOperate INTEGER
  hwEthernetClock INTEGER
  hwEthernetFlagJ0Mode INTEGER
  hwEthernetFlagJ0Value Integer32
  hwEthernetFlagJ0Trace STRING
  hwEthernetFlagJ1Mode INTEGER
  hwEthernetFlagJ1Value Integer32
  hwEthernetFlagJ1Trace STRING
  hwEthernetFlagC2Value Integer32
  hwEthernetUpHoldTime Integer32
  hwEthernetDownHoldTime Integer32
  hwEthernetSubinterfaceStatisticEnable EnabledStatus
  hwEthernetFlowControl INTEGER
  hwEthernetOffline INTEGER
  hwEthernetSetTransferMode INTEGER
  hwEthernetJumboframeMaxLength Integer32
  hwEthernetComboType INTEGER
  hwEthernetPortMode INTEGER
  hwEthernetNegotiationMode INTEGER

HwPosEntry  
SEQUENCE    
  hwPosIfIndex InterfaceIndex
  hwPosLinkProtocol INTEGER
  hwPosFrameFormat INTEGER
  hwPosLoopback INTEGER
  hwPosScramble EnabledStatus
  hwPosClock INTEGER
  hwPosCrcVerifyCode INTEGER
  hwPosFlagJ0Mode INTEGER
  hwPosFlagJ0Value Integer32
  hwPosFlagJ0Trace STRING
  hwPosFlagJ1Mode INTEGER
  hwPosFlagJ1Value Integer32
  hwPosFlagJ1Trace STRING
  hwPosFlagC2Value Integer32

HwCposEntry  
SEQUENCE    
  hwCposIfIndex InterfaceIndex
  hwCposClock INTEGER
  hwCposIfType INTEGER
  hwCposFrameFormat INTEGER
  hwCposMultiplex INTEGER
  hwCposLoopback INTEGER
  hwCposFlagJ0Mode INTEGER
  hwCposFlagJ0Value Integer32
  hwCposFlagJ0Trace STRING
  hwCposFlagJ1Mode INTEGER
  hwCposFlagJ1Value Integer32
  hwCposFlagJ1Trace STRING
  hwCposFlagC2Value Integer32
  hwCposB1SdAlarmThreshold Integer32
  hwCposB1ExcAlarmThreshold Integer32
  hwCposB2SdAlarmThreshold Integer32
  hwCposB2ExcAlarmThreshold Integer32
  hwCposB3SdAlarmThreshold Integer32
  hwCposB3ExcAlarmThreshold Integer32
  hwCposLpBipSdAlarmThreshold Integer32
  hwCposLpBipExcAlarmThreshold Integer32
  hwCposHighPathNumber Integer32
  hwCposLowPathNumber Integer32
  hwCposMappingMode INTEGER
  hwCposRxJ0Mode INTEGER
  hwCposRxJ1Mode INTEGER
  hwCposRxJ0Value Integer32
  hwCposRxJ1Value Integer32
  hwCposRxJ0Trace STRING
  hwCposRxJ1Trace STRING
  hwCposVc4Flag Integer32

HwCposLpEntry  
SEQUENCE    
  hwCposLpIfIndex InterfaceIndex
  hwCposLpId Integer32
  hwCposFlagJ2Mode INTEGER
  hwCposFlagJ2Value Integer32
  hwCposFlagJ2Trace STRING
  hwCposRxJ2Mode INTEGER
  hwCposRxJ2Value Integer32
  hwCposRxJ2Trace STRING

HwDs0ChannelBundleEntry  
SEQUENCE    
  hwDs0ChannelBundleParentIfIndex InterfaceIndex
  hwDs0ChannelBundleDs1ChannelId Integer32
  hwDs0ChannelBundleId Integer32
  hwDs0ChannelBundleIfIndex InterfaceIndex
  hwDs0ChannelBundleTimeSlots STRING
  hwDs0ChannelBundleSpeed INTEGER
  hwDs0ChannelBundleTimeSlot0 TruthValue
  hwDs0ChannelBundleIsMasterPW INTEGER
  hwDs0ChannelBundleMasterPWStatus INTEGER
  hwDs0ChannelBundlePortName STRING
  hwDs0ChannelBundleRowStatus RowStatus

HwDs1Entry  
SEQUENCE    
  hwDs1ParentIfIndex InterfaceIndex
  hwDs1ChannelId Integer32
  hwDs1IfIndex InterfaceIndex
  hwDs1ChannelType INTEGER
  hwDs1IfType INTEGER
  hwDs1Channelized TruthValue
  hwDs1CodeType INTEGER
  hwDs1Clock INTEGER
  hwDs1FrameFormat INTEGER
  hwDs1Cable INTEGER
  hwDs1Loopback INTEGER
  hwDs1ClockRecoveryDomain Integer32
  hwDs1PWClockDomain Integer32
  hwDs1WorkMode Integer32
  hwDs1EsAlarmTriggerThreshold Integer32
  hwDs1EsAlarmResumeThreshold Integer32
  hwDs1RowStatus RowStatus
  hwDs1Lbo INTEGER
  hwDs1CableLength INTEGER

HwDs3Entry  
SEQUENCE    
  hwDs3ParentIfIndex InterfaceIndex
  hwDs3ChannelId Integer32
  hwDs3IfIndex InterfaceIndex
  hwDs3ChannelType INTEGER
  hwDs3IfType INTEGER
  hwDs3Channelized TruthValue
  hwDs3Clock INTEGER
  hwDs3FrameFormat INTEGER
  hwDs3Scramble TruthValue
  hwDs3Cable INTEGER
  hwDs3NationalBit INTEGER
  hwDs3Loopback INTEGER
  hwDs3CreateSerial TruthValue
  hwDs3RowStatus RowStatus

HwBundleSerialEntry  
SEQUENCE    
  hwBundleSerialIfIndex InterfaceIndex
  hwBundleSerialLinkProtocol INTEGER
  hwBundleSerialTimerHold Integer32
  hwBundleSerialLoopback TruthValue
  hwBundleSerialCrcVerifyCode INTEGER

HwPhysicalPortEntry  
SEQUENCE    
  hwPhysicalPortIfIndex InterfaceIndex
  hwPhysicalPortDelayTime Unsigned32
  hwPhysicalPortDelayRemainTime Unsigned32
  hwPhysicalPortName STRING
  hwPhysicalPortInChassis Integer32
  hwPhysicalPortInSlot Integer32
  hwPhysicalPortInCard Integer32
  hwPhysicalPortInPort Integer32
  hwPhysicalAutoShutLaserEnable INTEGER
  hwPhysicalAutoShutLaserOpenInterval Integer32
  hwPhysicalAutoShutLaserCloseInterval Integer32
  hwPhysicalAutoShutLaserLongOpenInterval Integer32
  hwPhysicalLoopbackType INTEGER
  hwPhysicalShutLaser INTEGER
  hwPhysicalLaserStatus INTEGER
  hwPhysicalPortHoldUp INTEGER
  hwPhysicalPortAlarmInverseEnable INTEGER
  hwPhysicalPortInVsId Integer32
  hwPhysicalPortAlarmName STRING

HwSDHRsMsPerfCurrentEntry  
SEQUENCE    
  hwSDHRsMsPerfCurrentIfIndex InterfaceIndex
  hwSDHRsMsPerfCurrentDataIndex Integer32
  hwSDHRsPerfCurrentBBE Integer32
  hwSDHRsPerfCurrentES Integer32
  hwSDHRsPerfCurrentSES Integer32
  hwSDHRsPerfCurrentUAS Integer32
  hwSDHMsPerfCurrentBBE Integer32
  hwSDHMsPerfCurrentES Integer32
  hwSDHMsPerfCurrentSES Integer32
  hwSDHMsPerfCurrentUAS Integer32
  hwSDHMsPerfCurrentFEBBE Integer32
  hwSDHMsPerfCurrentFEES Integer32
  hwSDHMsPerfCurrentFESES Integer32
  hwSDHMsPerfCurrentFEUAS Integer32

HwSDHHpPerfCurrentEntry  
SEQUENCE    
  hwSDHHpPerfCurrentIfIndex InterfaceIndex
  hwSDHHpPerfCurrentHpIndex Integer32
  hwSDHHpPerfCurrentDataIndex Integer32
  hwSDHHpPerfCurrentBBE Integer32
  hwSDHHpPerfCurrentES Integer32
  hwSDHHpPerfCurrentSES Integer32
  hwSDHHpPerfCurrentUAS Integer32
  hwSDHHpPerfCurrentFEBBE Integer32
  hwSDHHpPerfCurrentFEES Integer32
  hwSDHHpPerfCurrentFESES Integer32
  hwSDHHpPerfCurrentFEUAS Integer32

HwSDHLpPerfCurrentEntry  
SEQUENCE    
  hwSDHLpPerfCurrentIfIndex InterfaceIndex
  hwSDHLpPerfCurrentHpIndex Integer32
  hwSDHLpPerfCurrentLpIndex Integer32
  hwSDHLpPerfCurrentDataIndex Integer32
  hwSDHLpPerfCurrentBBE Integer32
  hwSDHLpPerfCurrentES Integer32
  hwSDHLpPerfCurrentSES Integer32
  hwSDHLpPerfCurrentUAS Integer32
  hwSDHLpPerfCurrentFEBBE Integer32
  hwSDHLpPerfCurrentFEES Integer32
  hwSDHLpPerfCurrentFESES Integer32
  hwSDHLpPerfCurrentFEUAS Integer32

HwPDHPerfCurrentEntry  
SEQUENCE    
  hwPDHPerfCurrentIfIndex InterfaceIndex
  hwPDHPerfCurrentDataIndex Integer32
  hwPDHPerfCurrentBBE Integer32
  hwPDHPerfCurrentES Integer32
  hwPDHPerfCurrentSES Integer32
  hwPDHPerfCurrentUAS Integer32
  hwPDHPerfCurrentLCV Integer32

HwEthPortStatEntry  
SEQUENCE    
  hwEthPortStatIfIndex InterfaceIndex
  hwEthPortStatBadBytes Counter64
  hwEthPortStatOutPut64Bytes Counter64
  hwEthPortStatOutPut65to127Bytes Counter64
  hwEthPortStatOutPut128to255Bytes Counter64
  hwEthPortStatOutPut256to511Bytes Counter64
  hwEthPortStatOutPut512to1023Bytes Counter64
  hwEthPortStatOutPut1024to1518Bytes Counter64
  hwEthPortStatOutPut1519toMaxBytes Counter64

HwDslGroupEntry  
SEQUENCE    
  hwDslGroupIfIndex InterfaceIndex
  hwDslGroupWorkMode INTEGER
  hwDslGroupBisState INTEGER
  hwDslGroupEncapeMode INTEGER
  hwDslGroupEnable INTEGER
  hwDslGroupRowStatus RowStatus

HwDslGroupBoundVeEntry  
SEQUENCE    
  hwDslGroupIfIndexOfBound InterfaceIndex
  hwVirtualEthernetIfIndex InterfaceIndex
  hwDslGroupVpi Integer32
  hwDslGroupVci Integer32
  hwDslGroupPvcId Integer32
  hwBoundVeRowStatus RowStatus

HwDslGroupBindVeEntry  
SEQUENCE    
  hwDslGroupInterfaceIndex InterfaceIndex
  hwVirtualEthernetInterfaceIndex InterfaceIndex
  hwBindVeRowStatus RowStatus

HwDslGroupImaEntry  
SEQUENCE    
  hwDslGroupImaIfIndex InterfaceIndex
  hwDslGroupImaVersion INTEGER
  hwDslGroupImaFrameLen ImaFrameLength
  hwDslGroupImaReset INTEGER
  hwDslGroupImaTxMinLinkNum Integer32
  hwDslGroupImaRxMinLinkNum Integer32
  hwDslGroupImaNeState ImaGroupState
  hwDslGroupImaFeState ImaGroupState
  hwDslGroupImaTxCellRate Integer32
  hwDslGroupImaRxCellRate Integer32
  hwDslGroupImaTxActLinkNum Integer32
  hwDslGroupImaRxActLinkNum Integer32
  hwDslGroupImaIfName STRING

HwDslLinkEntry  
SEQUENCE    
  hwBoundDslGroupIfIndex InterfaceIndex
  hwDslLinkIfIndex InterfaceIndex
  hwDslLinkIfName STRING
  hwBoundDslGroupIfName STRING
  hwDslLinkBoundRowStatus RowStatus

HwPWAlarmEntry  
SEQUENCE    
  hwPWAlarmIfIndex InterfaceIndex
  hwPWCesVcID Integer32
  hwPWCesVcType Integer32
  hwPeerIpAddr IpAddress
  hwAlarmStatus Integer32
  hwPWAlarmRMLEnableStatus EnabledStatus
  hwLosAlarmTriggerThreshold Integer32
  hwLosAlarmResumeThreshold Integer32
  hwPWPortName STRING
  hwLosPktExcTriggerThreshold Integer32
  hwLosPktExcResumeThreshold Integer32
  hwMisorderPktExcTriggerThreshold Integer32
  hwMisorderPktExcResumeThreshold Integer32
  hwStrayPktExcTriggerThreshold Integer32
  hwStrayPktExcResumeThreshold Integer32
  hwMalPktExcTriggerThreshold Integer32
  hwMalPktExcResumeThreshold Integer32
  hwJtrUdrExcTriggerThreshold Integer32
  hwJtrUdrExcResumeThreshold Integer32
  hwJtrOvrExcTriggerThreshold Integer32
  hwJtrOvrExcResumeThreshold Integer32

HwAtmPWAlarmEntry  
SEQUENCE    
  hwAtmPWAlarmIfIndex InterfaceIndex
  hwAtmVcID Integer32
  hwAtmVcType Integer32
  hwAtmPeerIpAddr IpAddress
  hwAtmPWPortName STRING
  hwAtmLosPktExcTriggerThreshold Integer32
  hwAtmLosPktExcResumeThreshold Integer32
  hwAtmMisorderPktExcTriggerThreshold Integer32
  hwAtmMisorderPktExcResumeThreshold Integer32
  hwAtmUnknownCellExcTriggerThreshold Integer32
  hwAtmUnknownCellExcResumeThreshold Integer32

HwSNMPTrapEnEntry  
SEQUENCE    
  hwSNMPTrapEnIfIndex InterfaceIndex
  hwCesPWLopsEn Integer32
  hwCesPWRemoteLosPktEn Integer32
  hwCesPWOppositeRAIEn Integer32
  hwCesPWOppositeAcfaultEn Integer32
  hwCesPWLosPktEn Integer32
  hwCesPWMisorderPktEn Integer32
  hwCesPWStrayPktEn Integer32
  hwCesPWMalPktEn Integer32
  hwCesPWJtrUnrEn Integer32
  hwCesPWJtrOvrEn Integer32
  hwCesPWAllEn Integer32
  hwPhysicalPortLosAlarmEn Integer32
  hwPhysicalPortLofAlarmEn Integer32
  hwRsOofAlarmEn Integer32
  hwRsB1ExcAlarmEn Integer32
  hwRsB1SdAlarmEn Integer32
  hwRsJ0TimAlarmEn Integer32
  hwMsRdiAlarmEn Integer32
  hwMsB2ExcAlarmEn Integer32
  hwMsAuLopAlarmEn Integer32
  hwMsAisAlarmEn Integer32
  hwMsB2SdAlarmEn Integer32
  hwHpJ1TimAlarmEn Integer32
  hwHpUneqAlarmEn Integer32
  hwHpRdiAlarmEn Integer32
  hwHpB3ExcAlarmEn Integer32
  hwHpPlmAlarmEn Integer32
  hwHpB3SdAlarmEn Integer32
  hwHpAuAisAlarmEn Integer32
  hwLpTuLopAlarmEn Integer32
  hwHpTuLomAlarmEn Integer32
  hwLpTimAlarmEn Integer32
  hwLpUneqAlarmEn Integer32
  hwLpRdiAlarmEn Integer32
  hwLpBipExcAlarmEn Integer32
  hwLpBipSdAlarmEn Integer32
  hwLpPlmAlarmEn Integer32
  hwLpTuAisAlarmEn Integer32
  hwDs1EsExcAlarmEn Integer32
  hwDs1RmfaAlarmEn Integer32
  hwDs1LmfaAlarmEn Integer32
  hwDs1AisAlarmEn Integer32
  hwDs1RdiAlarmEn Integer32
  hwRsLocAlarmEn Integer32
  hwLpRfiAlarmEn Integer32
  hwLpV5VcaisAlarmEn Integer32
  hwVc12oofAlarmEn Integer32
  hwVc12AlmE1RaiAlarmEn Integer32
  hwVc12LfaAlarmEn Integer32
  hwVc12UpE1AisAlarmEn Integer32
  hwVc12DownE1AisAlarmEn Integer32
  hwDs1DownE1AisAlarmEn Integer32
  hwMsLpsUniBiMAlarmEn Integer32
  hwMsK1K2MAlarmEn Integer32
  hwMsK2MAlarmEn Integer32
  hwVc12LmfaAlarmEn Integer32
  hwSDHAllEn Integer32
  hwLaserShutAlarmEn Integer32
  hwLaserAutoShutAlarmEn Integer32
  hwLaserAllEn Integer32
  hwLoopbackAlarmEn Integer32
  hwChannelLoopbackAlarmEn Integer32
  hwLoopbackAllEn Integer32
  hwAtmOcdAlarmEn Integer32
  hwAtmLcdAlarmEn Integer32
  hwAtmUhcsAlarmEn Integer32
  hwAtmChcsAlarmEn Integer32
  hwAtmPWLosPktEn Integer32
  hwAtmPWMisorderPktEn Integer32
  hwAtmPWUnknownCellEn Integer32
  hwAtmAllEn Integer32

HwPortAlarmThresholdEntry  
SEQUENCE    
  hwPhysicalPortThrIfIndex InterfaceIndex
  hwPhysicalPortThrName STRING
  hwPhysicalPortCrcErrorStatistics Counter64
  hwPhysicalPortCrcErrorHighThreshold Unsigned32
  hwPhysicalPortCrcErrorLowThreshold Unsigned32
  hwPhysicalPortCrcErrorInterval Unsigned32
  hwPhysicalPortSymbolErrorStatistics Counter64
  hwPhysicalPortSymbolErrorHighThreshold Unsigned32
  hwPhysicalPortSymbolErrorLowThreshold Unsigned32
  hwPhysicalPortSymbolErrorInterval Unsigned32
  hwPhysicalPortInputErrorStatistics Counter64
  hwPhysicalPortInputErrorHighThreshold Unsigned32
  hwPhysicalPortInputErrorLowThreshold Unsigned32
  hwPhysicalPortInputErrorInterval Unsigned32
  hwPhysicalPortOutputErrorStatistics Counter64
  hwPhysicalPortOutputErrorHighThreshold Unsigned32
  hwPhysicalPortOutputErrorLowThreshold Unsigned32
  hwPhysicalPortOutputErrorInterval Unsigned32
  hwPhysicalPortSdhErrorStatistics Counter64
  hwPhysicalPortSdhErrorHighThreshold Unsigned32
  hwPhysicalPortSdhErrorLowThreshold Unsigned32
  hwPhysicalPortSdhErrorInterval Unsigned32
  hwPhysicalPortBIP8SDErrorThreshold Unsigned32
  hwPhysicalPortCrcPerAlarmThresholdCoefficient Unsigned32
  hwPhysicalPortCrcPerAlarmThresholdPower Unsigned32
  hwPhysicalPortCrcPerResumeThresholdCoefficient Unsigned32
  hwPhysicalPortCrcPerResumeThresholdPower Unsigned32
  hwPhysicalPortCrcPerTriggerLsp Unsigned32
  hwPhysicalPortCrcPerCurrentValueString STRING
  hwPhysicalPortCrcPerAlarmThresholdString STRING
  hwPhysicalPortCrcPerResumeThresholdString STRING
  hwPhysicalPortCrcPerTriggerSection Unsigned32
  hwPhysicalPortAlarmTypeThresholdCoefficient INTEGER
  hwPhysicalPortCrcSdAlarmThresholdCoefficient Unsigned32
  hwPhysicalPortCrcSdAlarmThresholdPower Unsigned32
  hwPhysicalPortCrcSdResumeThresholdCoefficient Unsigned32
  hwPhysicalPortCrcSdResumeThresholdPower Unsigned32
  hwPhysicalPortCrcExcAlarmThresholdCoefficient Unsigned32
  hwPhysicalPortCrcExcAlarmThresholdPower Unsigned32
  hwPhysicalPortCrcExcResumeThresholdCoefficient Unsigned32
  hwPhysicalPortCrcExcResumeThresholdPower Unsigned32
  hwPhysicalPortCrcSdAlarmThresholdString STRING
  hwPhysicalPortCrcSdResumeThresholdString STRING
  hwPhysicalPortCrcExcAlarmThresholdString STRING
  hwPhysicalPortCrcExcResumeThresholdString STRING
  hwPhysicalPortCrcPerAlarmCoefficientStatistics Unsigned32
  hwPhysicalPortCrcPerAlarmPowerStatistics Unsigned32
  hwPhysicalPortCrcSdAlarmTriggerLsp INTEGER
  hwPhysicalPortCrcExcAlarmTriggerLsp INTEGER
  hwPhysicalPortCrcPerWarningThresholdCoefficient Unsigned32
  hwPhysicalPortCrcPerWarningThresholdPower Unsigned32
  hwPhysicalPortCrcPerWarningResumeThresholdCoefficient Unsigned32
  hwPhysicalPortCrcPerWarningResumeThresholdPower Unsigned32
  hwPhysicalPortCrcPerWarningThresholdString STRING
  hwPhysicalPortCrcPerWarningResumeThresholdString STRING
  hwPhysicalPortPreFecCoefficientStatistics Unsigned32
  hwPhysicalPortPreFecPowerStatistics Unsigned32

HwPortAlarmDownEnableEntry  
SEQUENCE    
  hwPhysicalPortDownIfIndex InterfaceIndex
  hwPhysicalPortDownName STRING
  hwPhysicalPortCrcEnabledDown INTEGER
  hwPhysicalPortSymbolEnabledDown INTEGER
  hwPhysicalPortInputEnabledDown INTEGER
  hwPhysicalPortOutputEnabledDown INTEGER
  hwPhysicalPortSdhEnabledDown INTEGER
  hwPhysicalPortBip8SdEnabledDown INTEGER

HwPortProtectGroupCfgEntry  
SEQUENCE    
  hwPortProtectGroupId Integer32
  hwPortProtectMasterIfIndex Integer32
  hwPortProtectMasterStatus INTEGER
  hwPortProtectSlaveIfIndex Integer32
  hwPortProtectSlaveStatus INTEGER
  hwPortProtectRowStatus RowStatus

HwPortLineEntry  
SEQUENCE    
  hwPortLineIfIndex InterfaceIndex
  hwPortLineUpStreampbo Integer32
  hwPortLineDownStreampbo Integer32
  hwPortLineUpStreamLoopAtten Integer32
  hwPortLineDownStreamLoopAtten Integer32
  hwPortLineUpStreamSnrMargin Integer32
  hwPortLineDownStreamSnrMargin Integer32
  hwPortLineSpeed Integer32

HwPortIfStatEntry  
SEQUENCE    
  hwPortIfStatIfIndex InterfaceIndex
  hwPortIfStatIfInCrcPkts Integer32

HwPortDescriptionEntry  
SEQUENCE    
  hwPortDescriptionIfIndex Integer32
  hwPortDescriptionIfPortDescription INTEGER

HwPRBSTestPortStatusEntry  
SEQUENCE    
  hwPRBSTestPortStatusIfName STRING
  hwPRBSTestPortStatusSide INTEGER
  hwPRBSTestPortStatusSuportFlag INTEGER
  hwPRBSTestPortStatusPatternBitmap Unsigned32
  hwPRBSTestPortStatusErrInsertLevel Unsigned32
  hwPRBSTestPortStatusSlotNum Unsigned32
  hwPRBSTestPortStatusCardNum Unsigned32
  hwPRBSTestPortStatusPhyPortIfName STRING
  hwPRBSTestPortStatusResultCount Unsigned32
  hwPRBSTestPortStatusOngoingTestIndex Unsigned32

HwPRBSTestResultEntry  
SEQUENCE    
  hwPRBSTestResultIfName STRING
  hwPRBSTestResultTestIndex Unsigned32
  hwPRBSTestResultPhyPortIfName STRING
  hwPRBSTestResultSide INTEGER
  hwPRBSTestResultPattern Unsigned32
  hwPRBSTestResultIntervalTime Unsigned32
  hwPRBSTestResultIntervalCount Unsigned32
  hwPRBSTestResultTestingIntervalIndex Unsigned32
  hwPRBSTestResultStartTime DateAndTime
  hwPRBSTestResultStopTime DateAndTime
  hwPRBSTestResultProgress Unsigned32
  hwPRBSTestResultRemainTime Unsigned32
  hwPRBSTestResultErrInserted INTEGER
  hwPRBSTestResultTotalBit Counter64
  hwPRBSTestResultErrorBit Counter64
  hwPRBSTestResultBerCoe Unsigned32
  hwPRBSTestResultBerPow Unsigned32
  hwPRBSTestResultLos Unsigned32
  hwPRBSTestResultEs Unsigned32
  hwPRBSTestResultEfs Unsigned32
  hwPRBSTestResultSes Unsigned32
  hwPRBSTestResultUas Unsigned32
  hwPRBSTestResultSegmentTime Unsigned32
  hwPRBSTestResultSegmentTotalCount Unsigned32
  hwPRBSTestResultTestingSegmentIndex Unsigned32

HwPRBSTestIntervalEntry  
SEQUENCE    
  hwPRBSTestIntervalIfName STRING
  hwPRBSTestIntervalTestIndex Unsigned32
  hwPRBSTestIntervalIndex Unsigned32
  hwPRBSTestIntervalStartTime DateAndTime
  hwPRBSTestIntervalStopTime DateAndTime
  hwPRBSTestIntervalProgress Unsigned32
  hwPRBSTestIntervalRemainTime Unsigned32
  hwPRBSTestIntervalErrInserted INTEGER
  hwPRBSTestIntervalTotalBit Counter64
  hwPRBSTestIntervalErrorBit Counter64
  hwPRBSTestIntervalBerCoe Unsigned32
  hwPRBSTestIntervalBerPow Unsigned32
  hwPRBSTestIntervalLos Unsigned32
  hwPRBSTestIntervalEs Unsigned32
  hwPRBSTestIntervalEfs Unsigned32
  hwPRBSTestIntervalSes Unsigned32
  hwPRBSTestIntervalUas Unsigned32

HwPRBSTestSegmentEntry  
SEQUENCE    
  hwPRBSTestSegmentIfName STRING
  hwPRBSTestSegmentTestIndex Unsigned32
  hwPRBSTestSegmentIndex Unsigned32
  hwPRBSTestSegmentStartTime DateAndTime
  hwPRBSTestSegmentEndTime DateAndTime
  hwPRBSTestSegmentTotalBit Counter64
  hwPRBSTestSegmentErrorBit Counter64
  hwPRBSTestSegmentBerCoe Unsigned32
  hwPRBSTestSegmentBerPow Unsigned32
  hwPRBSTestSegmentLos Unsigned32
  hwPRBSTestSegmentEs Unsigned32
  hwPRBSTestSegmentEfs Unsigned32
  hwPRBSTestSegmentSes Unsigned32
  hwPRBSTestSegmentUas Unsigned32

HwOtnEntry  
SEQUENCE    
  hwOtnIfIndex InterfaceIndex
  hwOtnFecMode INTEGER

HwLogicalPortEntry  
SEQUENCE    
  hwLogicalPortIfIndex InterfaceIndex
  hwLogicalPortStatisticEnable INTEGER

Defined Values

hwPortMIB 1.3.6.1.4.1.2011.5.25.157
The private mib file includes the general extent information of the device.hwDatacomm(157).hwPortMIB
MODULE-IDENTITY    

hwPortMIBObjects 1.3.6.1.4.1.2011.5.25.157.1
OBJECT IDENTIFIER    

hwEthernet 1.3.6.1.4.1.2011.5.25.157.1.1
OBJECT IDENTIFIER    

hwEthernetTable 1.3.6.1.4.1.2011.5.25.157.1.1.1
Indicates the physical attributes of the Ethernet interface. This table lists the physical attributes of various Ethernet interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    HwEthernetEntry

hwEthernetEntry 1.3.6.1.4.1.2011.5.25.157.1.1.1.1
Indicates the physical attributes of the Ethernet interface. This table lists the physical attributes of various Ethernet interfaces.
OBJECT-TYPE    
  HwEthernetEntry  

hwEthernetIfIndex 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.1
Interface index(es) of port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwEthernetLoopback 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.11
The local loopback of an Ethernet interface is used to test the interface itself. If an interface works in a normal situation, disable the local loopback. By default, stopLoopback is used.
OBJECT-TYPE    
  INTEGER otherLoop(1), stopLoopback(2), local(3), remote(4)  

hwEthernetPortType 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.12
Indicates the type of the Ethernet interface: an optical interface or an electrical interface.
OBJECT-TYPE    
  INTEGER other(1), copper(2), fiber(3)  

hwEthernetSpeedSet 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.13
Indicates the speed of the Ethernet interface. This parameter takes effect only on some Ethernet electrical interfaces rather than optical interfaces. The parameter can be 10 M, 100 M, 1000 M, 10000 M,40000 M,20000 M,2500 M,5000 M.
OBJECT-TYPE    
  INTEGER other(1), speed10(2), speed100(3), speed1000(4), speed10000(5), speed40000(6), speed20000(7), speed2500(8), speed5000(9)  

hwEthernetDuplex 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.14
Indicates the duplex mode of the Ethernet interface. An electrical Ethernet interface can work in half-duplex mode or full-duplex mode. An optical Ethernet can work only in full-duplex mode.
OBJECT-TYPE    
  INTEGER full(1), half(2)  

hwEthernetNegotiation 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.15
Indicates the auto-negotiation mode of the Ethernet electrical interface. By default, auto-negotiation is enabled. The three objects, hwEthernetSpeedSet, hwEthernetDuplex, and hwEthernetNegotiation are associated with each other. If the auto-negotiation of hwEthernetNegotiation is enabled, the values of hwEthernetSpeedSet and hwEthernetDuplex are auto-negotiated. If hwEthernetSpeedSet is set to a certain value, hwEthernetDuplex is modified to the default value full, and hwEthernetNegotiation is automatically changed to disable. If the auto-negotiation of hwEthernetNegotiation is enabled, hwEthernetDuplex cannot be set.
OBJECT-TYPE    
  EnabledStatus  

hwEthernetPortTypeOperate 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.16
Indicates the link type of the Ethernet interface. The type can be optical link or electrical link. This parameter takes effect only on specific Ethernet interfaces.
OBJECT-TYPE    
  INTEGER other(1), copper(2), fiber100(3), fiber1000(4)  

hwEthernetClock 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.20
Indicates the mode of the clock. The mode can be master or slave. By default, the mode of a clock is slave. This parameter takes effect only on the WAN board.
OBJECT-TYPE    
  INTEGER master(1), slave(2)  

hwEthernetFlagJ0Mode 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.21
Before the 10 GE WAN board processes packets, the overhead byte must be configured on the interface. The overhead byte for the SDH frame, j0: Set section trace byte The default value is j016ByteMode(2):hwEthernetFlagJ0Trace:NetEngine
OBJECT-TYPE    
  INTEGER j01ByteMode(1), j016ByteMode(2), j064ByteOrNullMode(3), peer(4)  

hwEthernetFlagJ0Value 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.22
j01ByteMode Value. When hwEthernetFlagJ0Mode is set to j01ByteMode, this parameter takes effect.
OBJECT-TYPE    
  Integer32 0..255  

hwEthernetFlagJ0Trace 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.23
Set section trace byte. When hwEthernetFlagJ0Mode is set to j016ByteMode or j064ByteOrNullMode, this variable takes effect. When hwEthernetFlagJ0Mode is set to j016ByteMode, this variable is up to 15 characters trace byte. When hwEthernetFlagJ0Mode is set to j064ByteOrNullMode, this variable is up to 64 characters trace byte.
OBJECT-TYPE    
  STRING Size(0..64)  

hwEthernetFlagJ1Mode 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.24
Indicates the overhead byte of the SDH frame. j1:sets path trace byte. The default value is j116ByteMode(2) hwEthernetFlagJ1Trace NetEngine.
OBJECT-TYPE    
  INTEGER j11ByteMode(1), j116ByteMode(2), j164ByteOrNullMode(3), peer(4)  

hwEthernetFlagJ1Value 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.25
j11ByteMode Value. When hwEthernetFlagJ1Mode is set to j11ByteMode, this parameter takes effect.
OBJECT-TYPE    
  Integer32 0..255  

hwEthernetFlagJ1Trace 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.26
Set path trace byte. When hwEthernetFlagJ1Mode is set to j116ByteMode or j164ByteOrNullMode, this variable takes effect. When hwEthernetFlagJ1Mode is set to j116ByteMode, this variable is up to 15 characters trace byte. When hwEthernetFlagJ1Mode is set to j164ByteOrNullMode, this variable is up to 64 characters trace byte.
OBJECT-TYPE    
  STRING Size(0..64)  

hwEthernetFlagC2Value 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.27
Indicates the overhead byte of the SDH frame. c2: indicates the signal label byte. It is a hexdecimal value ranging from 00 to FF. The default value is 0x02.
OBJECT-TYPE    
  Integer32 0..255  

hwEthernetUpHoldTime 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.31
Indicates the response time to the event that the port turns Up. The units of hwEthernetUpHoldTime is millisecond.
OBJECT-TYPE    
  Integer32 0..86400000  

hwEthernetDownHoldTime 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.32
Indicates the response time to the event that the port turns Down. The units of hwEthernetDownHoldTime is millisecond.
OBJECT-TYPE    
  Integer32 0..86400000  

hwEthernetSubinterfaceStatisticEnable 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.33
Enable the statistical function of the sub-interface.
OBJECT-TYPE    
  EnabledStatus  

hwEthernetFlowControl 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.34
Set flow control of this port.
OBJECT-TYPE    
  INTEGER receive(1), send(2), both(3), none(4)  

hwEthernetOffline 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.35
Set Line protocol state to down of this port.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hwEthernetSetTransferMode 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.36
Set transfer mode of this port.
OBJECT-TYPE    
  INTEGER lan(1), wan(2), none(3), otn(4)  

hwEthernetJumboframeMaxLength 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.37
Set the jumboframe max length of this port.
OBJECT-TYPE    
  Integer32 1536..13296  

hwEthernetComboType 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.38
combo mode of this port.
OBJECT-TYPE    
  INTEGER auto(1), copper(2), fiber(3), other(4)  

hwEthernetPortMode 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.39
Indicates combo mode of this port.
OBJECT-TYPE    
  INTEGER copper(1), fiber(2), other(3)  

hwEthernetNegotiationMode 1.3.6.1.4.1.2011.5.25.157.1.1.1.1.40
Set negotiation-mode for phy of electronic GE port.The mode is uesed for synchronizing clock.
OBJECT-TYPE    
  INTEGER notsupport(1), auto(2), master(3), slave(4)  

hwPos 1.3.6.1.4.1.2011.5.25.157.1.2
OBJECT IDENTIFIER    

hwPosTable 1.3.6.1.4.1.2011.5.25.157.1.2.1
Indicates the physical attributes of the POS interface. This table lists the physical attributes of the POS interface.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPosEntry

hwPosEntry 1.3.6.1.4.1.2011.5.25.157.1.2.1.1
Indicates the physical attributes of the POS interface. This table lists the physical attributes of the POS interface.
OBJECT-TYPE    
  HwPosEntry  

hwPosIfIndex 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.1
Interface index(es) of port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwPosLinkProtocol 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.11
Indicates the link layer protocol of the POS interface. By default, on a POS interface, PPP serves as the link layer protocol.
OBJECT-TYPE    
  INTEGER ietf(1), nonstandard(2), hdlc(3), ppp(4)  

hwPosFrameFormat 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.12
Indicates the frame type of the POS interface. By default, the frame type of the POS interface is SDH. This variable identifies whether a SONET or a SDH signal is used across this interface.
OBJECT-TYPE    
  INTEGER sonet(1), sdh(2)  

hwPosLoopback 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.13
The local loopback of a POS interface is used to test the interface itself. If an interface works in a normal situation, disable the local loopback. By default, stopLoopback is used.
OBJECT-TYPE    
  INTEGER otherLoop(1), stopLoopback(2), local(3), remote(4)  

hwPosScramble 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.14
Indicates the scramble function of payload. By default, the scramble function of payload is enabled.
OBJECT-TYPE    
  EnabledStatus  

hwPosClock 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.15
Indicates whether the clock is in master mode or slave mode. By default, the clock is in slave mode.
OBJECT-TYPE    
  INTEGER master(1), slave(2)  

hwPosCrcVerifyCode 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.16
Indicates the length of the CRC verity code. The default value is 32.
OBJECT-TYPE    
  INTEGER crc16(1), crc32(2)  

hwPosFlagJ0Mode 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.21
Indicates the overhead byte of the SDH frame. j0: sets section trace byte. The default value is j016ByteMode(2);hwPosFlagJ0Trace:NetEngine.
OBJECT-TYPE    
  INTEGER j01ByteMode(1), j016ByteMode(2), j064ByteOrNullMode(3), peer(4)  

hwPosFlagJ0Value 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.22
Indicates the value of j01ByteMode. When hwPosFlagJ0Mode is set to j01ByteMode, hwPosFlagJ0Value takes effect.
OBJECT-TYPE    
  Integer32 0..127  

hwPosFlagJ0Trace 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.23
Set section trace byte. When hwPosFlagJ0Mode is set to j016ByteMode or j064ByteOrNullMode, this variable takes effect. When hwPosFlagJ0Mode is set to j016ByteMode, the value of this variable is up to 15 characters trace byte. When hwPosFlagJ0Mode is set to j064ByteOrNullMode, the value of this variable is up to 64 characters trace byte.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPosFlagJ1Mode 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.24
Indicates the overhead byte of the SDH frame. j1: sets path trace byte. The default value is j116ByteMode(2);hwPosFlagJ1Trace:NetEngine.
OBJECT-TYPE    
  INTEGER j11ByteMode(1), j116ByteMode(2), j164ByteOrNullMode(3), peer(4)  

hwPosFlagJ1Value 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.25
Indicates the value of j11ByteMode. When hwPosFlagJ1Mode is set to j11ByteMode, hwPosFlagJ1Value takes effect.
OBJECT-TYPE    
  Integer32 0..127  

hwPosFlagJ1Trace 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.26
Set path trace byte. When hwPosFlagJ1Mode is set to j116ByteMode or j164ByteOrNullMode, this variable takes effect. When hwPosFlagJ1Mode is set to j116ByteMode, this variable is up to 15 characters trace byte. When hwPosFlagJ1Mode is set to j164ByteOrNullMode, this variable is up to 64 characters trace byte.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPosFlagC2Value 1.3.6.1.4.1.2011.5.25.157.1.2.1.1.27
Indicates the overhead byte of the SDH frame. c2: indicates the signal label byte. It is a hexdecimal value ranging from 00 to FF. The default value is 0x02.
OBJECT-TYPE    
  Integer32 0..255  

hwCpos 1.3.6.1.4.1.2011.5.25.157.1.3
OBJECT IDENTIFIER    

hwCposTable 1.3.6.1.4.1.2011.5.25.157.1.3.1
Indicates the physical attributes of the CPOS interface. This table lists the physical attributes of the CPOS interface.
OBJECT-TYPE    
  SEQUENCE OF  
    HwCposEntry

hwCposEntry 1.3.6.1.4.1.2011.5.25.157.1.3.1.1
Indicates the physical attributes of the CPOS interface. This table lists the physical attributes of the CPOS interface.
OBJECT-TYPE    
  HwCposEntry  

hwCposIfIndex 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.1
Interface index(es) of port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwCposClock 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.11
Indicates whether the clock is in master mode or slave mode. By default, the clock is in slave mode.
OBJECT-TYPE    
  INTEGER master(1), slave(2)  

hwCposIfType 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.12
Indicates the interface type.
OBJECT-TYPE    
  INTEGER stm1(1), stm16(2)  

hwCposFrameFormat 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.13
Indicates the frame type of the CPOS interface. By default, the frame type of the CPOS interface is SDH.
OBJECT-TYPE    
  INTEGER sonet(1), sdh(2)  

hwCposMultiplex 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.14
Indicates the multiplex mode of the AUG. By default, the multiplex mode of the AUG is au-4.
OBJECT-TYPE    
  INTEGER au3(1), au4(2)  

hwCposLoopback 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.15
Indicates the loopback function of the CPOS interface. By default, the loopback function is disabled.
OBJECT-TYPE    
  INTEGER otherloop(1), stopLoopback(2), local(3), remote(4)  

hwCposFlagJ0Mode 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.21
Indicates the overhead byte of the SDH frame. j0: sets section trace byte. The default value is j016ByteMode(2);hwCposFlagJ0Trace NetEngine.
OBJECT-TYPE    
  INTEGER j01ByteMode(1), j016ByteMode(2), j064ByteOrNullMode(3), peer(4)  

hwCposFlagJ0Value 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.22
j01ByteMode Value . When hwCposFlagJ0Mode is set to j01ByteMode, hwCposFlagJ0Value takes effect.
OBJECT-TYPE    
  Integer32 0..127  

hwCposFlagJ0Trace 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.23
Set section trace byte. When hwCposFlagJ0Mode is set to j016ByteMode or j064ByteOrNullMode, this variable takes effect. When hwCposFlagJ0Mode is set to j016ByteMode, this variable is up to 15 characters trace byte. When hwCposFlagJ0Mode is set to j064ByteOrNullMode, this variable is up to 64 characters trace byte.
OBJECT-TYPE    
  STRING Size(0..64)  

hwCposFlagJ1Mode 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.24
Indicates the overhead byte of the SDH frame. j1: sets path trace byte. The default value is j116ByteMode(2);hwCposFlagJ1Trace NetEngine.
OBJECT-TYPE    
  INTEGER j11ByteMode(1), j116ByteMode(2), j164ByteOrNullMode(3), peer(4)  

hwCposFlagJ1Value 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.25
Indicates the value of j11ByteMode. When hwCposFlagJ1Mode is set to j11ByteMode, hwCposFlagJ1Value takes effect.
OBJECT-TYPE    
  Integer32 0..127  

hwCposFlagJ1Trace 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.26
Set path trace byte. When hwCposFlagJ1Mode is set to j116ByteMode or j164ByteOrNullMode, this variable takes effect. When hwCposFlagJ1Mode is set to j116ByteMode, this variable is a string up to 15 characters trace byte. When hwCposFlagJ1Mode is set to j164ByteOrNullMode, this variable is a string up to 64 characters trace byte.
OBJECT-TYPE    
  STRING Size(0..64)  

hwCposFlagC2Value 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.27
Indicates the overhead byte of the SDH frame. c2: indicates the signal label byte. It is a hexdecimal value ranging from 00 to FF. The default value is 22(0x16).
OBJECT-TYPE    
  Integer32 0..255  

hwCposB1SdAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.28
The threshold of B1 threshold crossing alarm.
OBJECT-TYPE    
  Integer32 1..9  

hwCposB1ExcAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.29
The threshold of B1 threshold crossing alarm.
OBJECT-TYPE    
  Integer32 1..9  

hwCposB2SdAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.30
The threshold of B2 threshold crossing alarm.
OBJECT-TYPE    
  Integer32 1..9  

hwCposB2ExcAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.31
The threshold of B2 threshold crossing alarm.
OBJECT-TYPE    
  Integer32 1..9  

hwCposB3SdAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.32
The threshold of B3 threshold crossing alarm.
OBJECT-TYPE    
  Integer32 1..9  

hwCposB3ExcAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.33
The threshold of B3 threshold crossing alarm.
OBJECT-TYPE    
  Integer32 1..9  

hwCposLpBipSdAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.34
The threshold of BIP2 threshold crossing alarm.
OBJECT-TYPE    
  Integer32 1..9  

hwCposLpBipExcAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.35
The threshold of BIP2 threshold crossing alarm.
OBJECT-TYPE    
  Integer32 1..9  

hwCposHighPathNumber 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.36
Indicates the overhead byte of the SDH frame. c2: indicates the signal label byte. It is a hexdecimal value ranging from 00 to FF. The default value is 22(0x16).
OBJECT-TYPE    
  Integer32 0..255  

hwCposLowPathNumber 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.37
Indicates the overhead byte of the SDH frame. c2: indicates the signal label byte. It is a hexdecimal value ranging from 00 to FF. The default value is 22(0x16).
OBJECT-TYPE    
  Integer32 0..255  

hwCposMappingMode 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.38
Indicates the mapping mode of cpos port, default if h-mode(1).
OBJECT-TYPE    
  INTEGER hMode(1), lMode(2), aMode(3)  

hwCposRxJ0Mode 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.39
Indicates the received J0 mode.
OBJECT-TYPE    
  INTEGER j01ByteMode(1), j016ByteMode(2), j064ByteOrNullMode(3), peer(4)  

hwCposRxJ1Mode 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.40
Indicates the received J1 mode.
OBJECT-TYPE    
  INTEGER j11ByteMode(1), j116ByteMode(2), j164ByteOrNullMode(3), peer(4)  

hwCposRxJ0Value 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.41
Indicates the received J0 value of 1-byte mode.
OBJECT-TYPE    
  Integer32 0..127  

hwCposRxJ1Value 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.42
Indicates the received J1 value of 1-byte mode.
OBJECT-TYPE    
  Integer32 0..127  

hwCposRxJ0Trace 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.43
Indicates the received J0 characters of 16-byte or 64-byte mode.
OBJECT-TYPE    
  STRING Size(0..64)  

hwCposRxJ1Trace 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.44
Indicates the received J1 characters of 16-byte or 64-byte mode.
OBJECT-TYPE    
  STRING Size(0..64)  

hwCposVc4Flag 1.3.6.1.4.1.2011.5.25.157.1.3.1.1.45
The value of this object identifies whether a VC4 channel can be created on the CPOS interface. 0 indicates that no VC4 channel can be created on the CPOS interface. 1 indicates that a VC4 channel can be created but has not been created on the CPOS interface. 2 indicates that a VC4 channel can be created and has been created on the CPOS interface.
OBJECT-TYPE    
  Integer32 0..2  

hwPortPhysicalHpIndex 1.3.6.1.4.1.2011.5.25.157.1.3.2
Indicates the higher order path number.
OBJECT-TYPE    
  Integer32  

hwPortPhysicalLpIndex 1.3.6.1.4.1.2011.5.25.157.1.3.3
Indicates the low order path number.
OBJECT-TYPE    
  Integer32  

hwCposLpTable 1.3.6.1.4.1.2011.5.25.157.1.3.4
Description.
OBJECT-TYPE    
  SEQUENCE OF  
    HwCposLpEntry

hwCposLpEntry 1.3.6.1.4.1.2011.5.25.157.1.3.4.1
Description.
OBJECT-TYPE    
  HwCposLpEntry  

hwCposLpIfIndex 1.3.6.1.4.1.2011.5.25.157.1.3.4.1.1
Description.
OBJECT-TYPE    
  InterfaceIndex  

hwCposLpId 1.3.6.1.4.1.2011.5.25.157.1.3.4.1.2
Description.
OBJECT-TYPE    
  Integer32  

hwCposFlagJ2Mode 1.3.6.1.4.1.2011.5.25.157.1.3.4.1.3
Description.
OBJECT-TYPE    
  INTEGER j21ByteMode(1), j216ByteMode(2)  

hwCposFlagJ2Value 1.3.6.1.4.1.2011.5.25.157.1.3.4.1.4
Description.
OBJECT-TYPE    
  Integer32 0..127  

hwCposFlagJ2Trace 1.3.6.1.4.1.2011.5.25.157.1.3.4.1.5
Description.
OBJECT-TYPE    
  STRING Size(0..16)  

hwCposRxJ2Mode 1.3.6.1.4.1.2011.5.25.157.1.3.4.1.6
Indicates the received J2 mode.
OBJECT-TYPE    
  INTEGER j21ByteMode(1), j216ByteMode(2)  

hwCposRxJ2Value 1.3.6.1.4.1.2011.5.25.157.1.3.4.1.7
Indicates the received J2 value of 1-byte mode.
OBJECT-TYPE    
  Integer32 0..127  

hwCposRxJ2Trace 1.3.6.1.4.1.2011.5.25.157.1.3.4.1.8
Indicates the received J2 characters of 16-byte or 64-byte mode.
OBJECT-TYPE    
  STRING Size(0..16)  

hwDs0ChannelBundle 1.3.6.1.4.1.2011.5.25.157.1.4
OBJECT IDENTIFIER    

hwDs0ChannelBundleTable 1.3.6.1.4.1.2011.5.25.157.1.4.1
This table is used to bundle timeslots of CE1/CT1 interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    HwDs0ChannelBundleEntry

hwDs0ChannelBundleEntry 1.3.6.1.4.1.2011.5.25.157.1.4.1.1
This table is used to bundle timeslots of CE1/CT1 interfaces.
OBJECT-TYPE    
  HwDs0ChannelBundleEntry  

hwDs0ChannelBundleParentIfIndex 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.1
Indicates the index of the parent interface.
OBJECT-TYPE    
  InterfaceIndex  

hwDs0ChannelBundleDs1ChannelId 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.2
Indicates the channel ID.
OBJECT-TYPE    
  Integer32  

hwDs0ChannelBundleId 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.3
Indicates the index number of the channel set.
OBJECT-TYPE    
  Integer32 0..30  

hwDs0ChannelBundleIfIndex 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.11
Indicates the index of the serial interface formed by the timeslot binding.
OBJECT-TYPE    
  InterfaceIndex  

hwDs0ChannelBundleTimeSlots 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.12
Indicates the number of the range of the timeslot to be bound. The value is an integer ranging from 0 to 31. Multiple timeslots are separated by ','. The range of timeslot is expressed by using '-'. For E1 card mode: If the timeslots are '0-31', it means unframed format, If the timeslots are '0-30', it means framed format, For T1 card mode: If the timeslots are '0-23', it means unframed format, If the timeslots are '0-22', it means framed format, and hwDs0ChannelBundleDs1ChannelId and hwDs0ChannelBundleId should be zero.
OBJECT-TYPE    
  STRING Size(0..61)  

hwDs0ChannelBundleSpeed 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.13
Configures the mode to configure the timeslots. If the parameter 56 k is selected, the timeslots are bound in the mode of N x 56 kbit/s. If the parameter 64 k is selected, the timeslots are bound in the mode of N x 64 kbit/s. If the parameter 150336 k is selected, the interface is used for remarking the CEP interface. The default value is 64kbit/s.
OBJECT-TYPE    
  INTEGER s56(1), s64(2), s150336(3)  

hwDs0ChannelBundleTimeSlot0 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.14
Indicates the timeslot0 to be bound or a single channel. The ture value indicates it will be create TDM channel.
OBJECT-TYPE    
  TruthValue  

hwDs0ChannelBundleIsMasterPW 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.15
Indicates if the pw configed on this port is master pw.
OBJECT-TYPE    
  INTEGER notacrpw(0), masterpw(1), notmasterpw(2)  

hwDs0ChannelBundleMasterPWStatus 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.16
Indicates the status of master pw.
OBJECT-TYPE    
  INTEGER unlock(0), lock(1)  

hwDs0ChannelBundlePortName 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.17
Port name.
OBJECT-TYPE    
  STRING  

hwDs0ChannelBundleRowStatus 1.3.6.1.4.1.2011.5.25.157.1.4.1.1.51
This variable is used to create or delete an object.
OBJECT-TYPE    
  RowStatus  

hwDs1 1.3.6.1.4.1.2011.5.25.157.1.5
OBJECT IDENTIFIER    

hwDs1Table 1.3.6.1.4.1.2011.5.25.157.1.5.1
This table lists all E1/CE1 interfaces or T1/CT1 interfaces. After the mode of E3/CE3 interfaces or T3/CT3 interfaces is set to channelized, this table can be used to create E1/CE1, or T1/CT1, or E3/CE3, or T3/CT3 interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    HwDs1Entry

hwDs1Entry 1.3.6.1.4.1.2011.5.25.157.1.5.1.1
This table lists all E1/CE1 interfaces or T1/CT1 interfaces. After the mode of E3/CE3 interfaces or T3/CT3 interfaces is set to channelized, this table can be used to create E1/CE1, or T1/CT1, or E3/CE3, or T3/CT3 interfaces.
OBJECT-TYPE    
  HwDs1Entry  

hwDs1ParentIfIndex 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.1
Indicates the index of the parent interface.
OBJECT-TYPE    
  InterfaceIndex  

hwDs1ChannelId 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.2
Indicates the channel ID.
OBJECT-TYPE    
  Integer32 0..63  

hwDs1IfIndex 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.3
Indicates the interface index.
OBJECT-TYPE    
  InterfaceIndex  

hwDs1ChannelType 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.11
Indicates the interface type. The type can be E1/CE1 or T1/CT1.
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

hwDs1IfType 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.12
Indicates the interface tyep. e3: is multiplexed by CE3 interfaces. t3: is multiplexed by CT3 interfaces. cpos: is multiplexed by CPOS interfaces. atm: is multiplexed by ATM interfaces. none: indicates the physical interface. default:none
OBJECT-TYPE    
  INTEGER e3(1), t3(2), cpos(3), atm(4), none(255)  

hwDs1Channelized 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.13
Indicates the working mode of the interface. true: indicates the channelized mode. false: indicates the clear channel mode. The default is true.
OBJECT-TYPE    
  TruthValue  

hwDs1CodeType 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.14
Indicates the code type of the interface. ami: is short for Alternate Mark Inversion. hdb3: is short for High Density Bipolar of Order 3. b8zs: is short for Bipolar with 8-Zero Substitution. none: is not supported
OBJECT-TYPE    
  INTEGER ami(1), hdb3(2), b8zs(3), none(255)  

hwDs1Clock 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.15
Indicates the clock mode of the interface. master: indicates that the clock works in master mode and uses the internal clock signal. slave: indicates that the clock works in slave mode and uses the line clock signal.
OBJECT-TYPE    
  INTEGER master(1), slave(2)  

hwDs1FrameFormat 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.16
Indicates the frame format of the interface. crc4: indicates that the frame format is CRC4. no-crc4: indicates that the frame format is no-CRC4. sf: indicates that the frame format is Super Frame. esf: indicates that the frame format is Extended Super Frame. By default, the frame format of an E1 interface is no-crc4. By default, the frame format of a T1 interface is esf.
OBJECT-TYPE    
  INTEGER esf(1), sf(2), noCrc4(3), crc(4)  

hwDs1Cable 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.17
The cable command takes effect only if the E1 interface card uses 75-ohm coaxial cable. The default is short. If no cable is connected, this parameter is displayed as null.
OBJECT-TYPE    
  INTEGER long(1), short(2), none(255)  

hwDs1Loopback 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.18
Enable the loopback function of the interface. local: enables the local loopback on the interface. remote: enables the remote loopback on the interface. payload: enables the remote payload loopback on the interface. cell: enables the local cell loopback. The local cell loopback is used to test the local physical chip.
OBJECT-TYPE    
  INTEGER local(1), remote(2), payload(3), cell(4), none(255)  

hwDs1ClockRecoveryDomain 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.19
Indicates the clock recovery domain of the interface.
OBJECT-TYPE    
  Integer32 0..8  

hwDs1PWClockDomain 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.20
Indicates the clock recovery domain of the interface.
OBJECT-TYPE    
  Integer32 0..8  

hwDs1WorkMode 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.21
Indicates the clock recovery domain of the interface.
OBJECT-TYPE    
  Integer32 0..8  

hwDs1EsAlarmTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.22
The trigger threshold of code violation count threshold crossing alarm of E1 line side .
OBJECT-TYPE    
  Integer32 1..900  

hwDs1EsAlarmResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.23
The resume threshold of code violation count threshold crossing alarm of E1 line side .
OBJECT-TYPE    
  Integer32 1..900  

hwDs1RowStatus 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.51
This variable is used to create or delete an object.
OBJECT-TYPE    
  RowStatus  

hwDs1Lbo 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.52
The lbo of T1 port. Unit: db. the value is expanded 10 times,so the real value should be reduced 10 times
OBJECT-TYPE    
  INTEGER db75(1), db155(2), db225(3), none(4), notsupport(5)  

hwDs1CableLength 1.3.6.1.4.1.2011.5.25.157.1.5.1.1.53
The cableLength of T1 port. Unit: feet.
OBJECT-TYPE    
  INTEGER length133(1), length266(2), length399(3), length533(4), length655(5), notsupport(6), none(255)  

hwDs3 1.3.6.1.4.1.2011.5.25.157.1.6
OBJECT IDENTIFIER    

hwDs3Table 1.3.6.1.4.1.2011.5.25.157.1.6.1
This table lists all E3/CE3 interfaces or all T3/CT3 interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    HwDs3Entry

hwDs3Entry 1.3.6.1.4.1.2011.5.25.157.1.6.1.1
This table lists all E3/CE3 interfaces or all T3/CT3 interfaces.
OBJECT-TYPE    
  HwDs3Entry  

hwDs3ParentIfIndex 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.1
Indicates the index of the parent interface.
OBJECT-TYPE    
  InterfaceIndex  

hwDs3ChannelId 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.2
Indicates the index of the parent interface.
OBJECT-TYPE    
  Integer32 0..3  

hwDs3IfIndex 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.3
Indicates the interface index.
OBJECT-TYPE    
  InterfaceIndex  

hwDs3ChannelType 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.11
Indicates the interface type. The type can be E3/CE3 or T3/CT3.
OBJECT-TYPE    
  INTEGER t3(1), e3(2)  

hwDs3IfType 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.12
Indicates the parent interface type of the interface. cpos: is multiplexed by CPOS interfaces. none: indicates the interface is a physical interface. The default is none.
OBJECT-TYPE    
  INTEGER cpos(1), none(255)  

hwDs3Channelized 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.13
Indicates the working mode of the interface. true: indicates the channelized mode. false: indicates the clear channel mode. The default is true.
OBJECT-TYPE    
  TruthValue  

hwDs3Clock 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.14
Indicates the clock mode of the interface. master: indicates that the clock works in master mode and uses the internal clock signal. slave: indicates that the clock works in slave mode and uses the line clock signal.
OBJECT-TYPE    
  INTEGER master(1), slave(2)  

hwDs3FrameFormat 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.15
Indicates the frame format of the interface.
OBJECT-TYPE    
  INTEGER g832Adm(1), g751Adm(2), g751Plcp(3), cbitAdm(4), cbitPlcp(5), m23Adm(6), m23Plcp(7)  

hwDs3Scramble 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.16
Indicates the scramble function of the interface. true: enables the scramble function. false: disables the scramble function. The default is false.
OBJECT-TYPE    
  TruthValue  

hwDs3Cable 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.17
The cable command takes effect only if the E3 interface card uses 75-ohm coaxial cable. The default is short. If no cable is connected, this parameter is displayed as null.
OBJECT-TYPE    
  INTEGER long(1), short(2)  

hwDs3NationalBit 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.18
Indicates the national bit of the E3/CE3 interface. n0: indicates the national bit is 0 and the interface supports only the communication within a country. n1: indicates the national bit is 1 and the interface supports the international communication.
OBJECT-TYPE    
  INTEGER n0(1), n1(2)  

hwDs3Loopback 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.19
Enable the loopback function of the interface. local: enables the local loopback on the interface. remote: enables the remote loopback on the interface. payload: enables the remote payload loopback on the interface. cell: enables the local cell loopback. The local cell loopback is used to test the local physical chip.
OBJECT-TYPE    
  INTEGER local(1), remote(2), payload(3), cell(4), none(255)  

hwDs3CreateSerial 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.20
Create serial interface from Ds3 interface. True create serial interface. False destroy serial interface.
OBJECT-TYPE    
  TruthValue  

hwDs3RowStatus 1.3.6.1.4.1.2011.5.25.157.1.6.1.1.51
This variable is used to create or delete an object.
OBJECT-TYPE    
  RowStatus  

hwBundleSerial 1.3.6.1.4.1.2011.5.25.157.1.7
OBJECT IDENTIFIER    

hwBundleSerialTable 1.3.6.1.4.1.2011.5.25.157.1.7.1
Indicates the attribute of the serial interface formed by timeslots. This table lists the physical attributes of the serial interface.
OBJECT-TYPE    
  SEQUENCE OF  
    HwBundleSerialEntry

hwBundleSerialEntry 1.3.6.1.4.1.2011.5.25.157.1.7.1.1
Indicates the attribute of the serial interface formed by timeslots. This table lists the physical attributes of the serial interface.
OBJECT-TYPE    
  HwBundleSerialEntry  

hwBundleSerialIfIndex 1.3.6.1.4.1.2011.5.25.157.1.7.1.1.1
Interface index(es) of serial(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwBundleSerialLinkProtocol 1.3.6.1.4.1.2011.5.25.157.1.7.1.1.11
The link-protocol of interface. The serial(s) always use PPP as its link-protocol for default.
OBJECT-TYPE    
  INTEGER ietf(1), nonstandard(2), hdlc(3), ppp(4), lapb(5), atm(6), tdm(7), none(255)  

hwBundleSerialTimerHold 1.3.6.1.4.1.2011.5.25.157.1.7.1.1.12
Indicates the interval for sending Keepalive packets from the serial interface to the peer. The default is 10 seconds.
OBJECT-TYPE    
  Integer32 0..32767  

hwBundleSerialLoopback 1.3.6.1.4.1.2011.5.25.157.1.7.1.1.13
true: enables the loopback on the serial interface. false: disables the loopback on the serial interface. By default, the loopback on the serial interface is disabled.
OBJECT-TYPE    
  TruthValue  

hwBundleSerialCrcVerifyCode 1.3.6.1.4.1.2011.5.25.157.1.7.1.1.14
Indicates the length of the CRC verify code. The default is 32.
OBJECT-TYPE    
  INTEGER crc16(1), crc32(2)  

hwPhysicalPort 1.3.6.1.4.1.2011.5.25.157.1.8
OBJECT IDENTIFIER    

hwPhysicalPortTable 1.3.6.1.4.1.2011.5.25.157.1.8.1
Indicates the attribute of the physical port.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPhysicalPortEntry

hwPhysicalPortEntry 1.3.6.1.4.1.2011.5.25.157.1.8.1.1
Indicates the attribute of the physical port.
OBJECT-TYPE    
  HwPhysicalPortEntry  

hwPhysicalPortIfIndex 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.1
Interface index(es) of physical port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwPhysicalPortDelayTime 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.2
Indicates the port tx enabling delay time. The units of hwPhysicalPortDelayTime is millisecond. The default value is 0 ms.
OBJECT-TYPE    
  Unsigned32 0..86400000  

hwPhysicalPortDelayRemainTime 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.3
Indicates the remnant time of enabling port-tx. The units of hwPhysicalPortDelayTime is millisecond.
OBJECT-TYPE    
  Unsigned32 0..86400000  

hwPhysicalPortName 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.4
Indicates the physical port name.
OBJECT-TYPE    
  STRING  

hwPhysicalPortInChassis 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.5
Indicates the physical port in chassis.
OBJECT-TYPE    
  Integer32  

hwPhysicalPortInSlot 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.6
Indicates the SlotID.
OBJECT-TYPE    
  Integer32  

hwPhysicalPortInCard 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.7
Indicates the CardID.
OBJECT-TYPE    
  Integer32  

hwPhysicalPortInPort 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.8
Indicates the PortID.
OBJECT-TYPE    
  Integer32  

hwPhysicalAutoShutLaserEnable 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.9
Indicates enable or disable the laser auto shut . Default is disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notsupport(255)  

hwPhysicalAutoShutLaserOpenInterval 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.10
Indicates the open interval of laser auto shut . The default value is 200 (unit: 10 ms). The value 2147483647 means that the interface doesn't support laser auto shut.
OBJECT-TYPE    
  Integer32 100..300 | 2147483647  

hwPhysicalAutoShutLaserCloseInterval 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.11
Indicates the close interval of laser auto shut . The default value is 6000 (unit: 10 ms). The value 2147483647 means that the interface doesn't support laser auto shut.
OBJECT-TYPE    
  Integer32 200..30000 | 2147483647  

hwPhysicalAutoShutLaserLongOpenInterval 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.12
Indicates the long open interval of laser auto shut . The default value is 9000 (unit: 10 ms). The value 2147483647 means that the interface doesn't support laser auto shut.
OBJECT-TYPE    
  Integer32 200..30000 | 2147483647  

hwPhysicalLoopbackType 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.13
The current state of loopbackType in port.
OBJECT-TYPE    
  INTEGER stopLoopback(0), local(1), remote(2)  

hwPhysicalShutLaser 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.14
Turn on or turn off the laser.
OBJECT-TYPE    
  INTEGER off(1), on(2), notsupport(255)  

hwPhysicalLaserStatus 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.15
The current status of the laser.
OBJECT-TYPE    
  INTEGER off(1), on(2), offline(3), notsupport(255)  

hwPhysicalPortHoldUp 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.16
Indicates enable or disable the interface to remain Up , the default value is disable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hwPhysicalPortAlarmInverseEnable 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.17
Config port alarm inverse enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwPhysicalPortInVsId 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.18
VsId.
OBJECT-TYPE    
  Integer32  

hwPhysicalPortAlarmName 1.3.6.1.4.1.2011.5.25.157.1.8.1.1.19
Indicates the physical port alarm name.
OBJECT-TYPE    
  STRING  

hwSDHRsMsPerfCurrentTable 1.3.6.1.4.1.2011.5.25.157.1.8.2
Indicates the performance stat of the Regenerator Section.
OBJECT-TYPE    
  SEQUENCE OF  
    HwSDHRsMsPerfCurrentEntry

hwSDHRsMsPerfCurrentEntry 1.3.6.1.4.1.2011.5.25.157.1.8.2.1
Indicates the performance stat of the Regenerator Section.
OBJECT-TYPE    
  HwSDHRsMsPerfCurrentEntry  

hwSDHRsMsPerfCurrentIfIndex 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.1
Interface index(es) of port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwSDHRsMsPerfCurrentDataIndex 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.2
Data index(es) of port(s) present on the device .
OBJECT-TYPE    
  Integer32 0..1  

hwSDHRsPerfCurrentBBE 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.3
Regenerator Section Background Block Error.
OBJECT-TYPE    
  Integer32  

hwSDHRsPerfCurrentES 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.4
Regenerator Section Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHRsPerfCurrentSES 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.5
Regenerator Section Severely Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHRsPerfCurrentUAS 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.6
Regenerator section unavailable second.
OBJECT-TYPE    
  Integer32  

hwSDHMsPerfCurrentBBE 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.7
Multiplex Section Background Block Error.
OBJECT-TYPE    
  Integer32  

hwSDHMsPerfCurrentES 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.8
Multiplex Section Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHMsPerfCurrentSES 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.9
Multiplex Section Severely Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHMsPerfCurrentUAS 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.10
Multiplex Section Unavaliable Seconds.
OBJECT-TYPE    
  Integer32  

hwSDHMsPerfCurrentFEBBE 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.11
Multiplex Section Far end Background Block Error.
OBJECT-TYPE    
  Integer32  

hwSDHMsPerfCurrentFEES 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.12
Multiplex Section Far end Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHMsPerfCurrentFESES 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.13
Multiplex Section Far end Severely Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHMsPerfCurrentFEUAS 1.3.6.1.4.1.2011.5.25.157.1.8.2.1.14
Multiplex Section Far end Unavaliable Seconds.
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentTable 1.3.6.1.4.1.2011.5.25.157.1.8.3
Indicates the performance stat of the Higher order Path.
OBJECT-TYPE    
  SEQUENCE OF  
    HwSDHHpPerfCurrentEntry

hwSDHHpPerfCurrentEntry 1.3.6.1.4.1.2011.5.25.157.1.8.3.1
Indicates the performance stat of the Higher order Path.
OBJECT-TYPE    
  HwSDHHpPerfCurrentEntry  

hwSDHHpPerfCurrentIfIndex 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.1
Interface index(es) of port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwSDHHpPerfCurrentHpIndex 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.2
Higher order Path index(es) of port(s) present on the device .
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentDataIndex 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.3
Data index(es) of port(s) present on the device .
OBJECT-TYPE    
  Integer32 0..1  

hwSDHHpPerfCurrentBBE 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.4
Multiplex Section Far end Unavaliable Seconds.
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentES 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.5
Higher order Path Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentSES 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.6
Higher order Path Severely Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentUAS 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.7
Higher order Path Unavaliable Seconds.
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentFEBBE 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.8
Higher order Path Far end Background Block Error.
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentFEES 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.9
Higher order Path Far end Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentFESES 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.10
Higher order Path Far end Severely Errored Second.
OBJECT-TYPE    
  Integer32  

hwSDHHpPerfCurrentFEUAS 1.3.6.1.4.1.2011.5.25.157.1.8.3.1.11
Higher order Path Far end Unavaliable Seconds.
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentTable 1.3.6.1.4.1.2011.5.25.157.1.8.4
Indicates the performance stat of the Low order Path.
OBJECT-TYPE    
  SEQUENCE OF  
    HwSDHLpPerfCurrentEntry

hwSDHLpPerfCurrentEntry 1.3.6.1.4.1.2011.5.25.157.1.8.4.1
Indicates the performance stat of the Low order Path.
OBJECT-TYPE    
  HwSDHLpPerfCurrentEntry  

hwSDHLpPerfCurrentIfIndex 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.1
Interface index(es) of port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwSDHLpPerfCurrentHpIndex 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.2
Higher order Path index(es) of port(s) present on the device .
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentLpIndex 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.3
Low order Path index(es) of port(s) present on the device .
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentDataIndex 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.4
Data index(es) of port(s) present on the device .
OBJECT-TYPE    
  Integer32 0..1  

hwSDHLpPerfCurrentBBE 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.5
Low order Path Background Block Error.
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentES 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.6
Low order Path errored seconds.
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentSES 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.7
Low order Path severely errored seconds.
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentUAS 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.8
Low order Path Unavailable second.
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentFEBBE 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.9
Low order Path Far-end Background Block Error.
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentFEES 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.10
Low order Path Far-end errored seconds.
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentFESES 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.11
Low order Path Far-end severely errored seconds.
OBJECT-TYPE    
  Integer32  

hwSDHLpPerfCurrentFEUAS 1.3.6.1.4.1.2011.5.25.157.1.8.4.1.12
Low order Path Far-end Unavailable second.
OBJECT-TYPE    
  Integer32  

hwPDHPerfCurrentTable 1.3.6.1.4.1.2011.5.25.157.1.8.5
Indicates the performance stat of the E1 line side.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPDHPerfCurrentEntry

hwPDHPerfCurrentEntry 1.3.6.1.4.1.2011.5.25.157.1.8.5.1
Indicates the performance stat of the E1 line side.
OBJECT-TYPE    
  HwPDHPerfCurrentEntry  

hwPDHPerfCurrentIfIndex 1.3.6.1.4.1.2011.5.25.157.1.8.5.1.1
Interface index(es) of port(s) present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwPDHPerfCurrentDataIndex 1.3.6.1.4.1.2011.5.25.157.1.8.5.1.2
Data index(es) of port(s) present on the device.
OBJECT-TYPE    
  Integer32 0..1  

hwPDHPerfCurrentBBE 1.3.6.1.4.1.2011.5.25.157.1.8.5.1.3
Low order Path Background Block Error.
OBJECT-TYPE    
  Integer32  

hwPDHPerfCurrentES 1.3.6.1.4.1.2011.5.25.157.1.8.5.1.4
E1 line side code violation errored second.
OBJECT-TYPE    
  Integer32  

hwPDHPerfCurrentSES 1.3.6.1.4.1.2011.5.25.157.1.8.5.1.5
E1 line side code violation severely errored second.
OBJECT-TYPE    
  Integer32  

hwPDHPerfCurrentUAS 1.3.6.1.4.1.2011.5.25.157.1.8.5.1.6
E1 line side code violation loss-of-signal second.
OBJECT-TYPE    
  Integer32  

hwPDHPerfCurrentLCV 1.3.6.1.4.1.2011.5.25.157.1.8.5.1.7
E1 line side code violation count.
OBJECT-TYPE    
  Integer32  

hwEthPortStatTable 1.3.6.1.4.1.2011.5.25.157.1.8.6
Indicates the stat of the ethernet interface.
OBJECT-TYPE    
  SEQUENCE OF  
    HwEthPortStatEntry

hwEthPortStatEntry 1.3.6.1.4.1.2011.5.25.157.1.8.6.1
Indicates the stat of the ethernet interface.
OBJECT-TYPE    
  HwEthPortStatEntry  

hwEthPortStatIfIndex 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.1
Interface index(es) of port(s) present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwEthPortStatBadBytes 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.2
Indicates the stat of badbytes.
OBJECT-TYPE    
  Counter64  

hwEthPortStatOutPut64Bytes 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.3
The total number of packets (including bad packets) output that were 64 octets in length (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter64  

hwEthPortStatOutPut65to127Bytes 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.4
The total number of packets (including bad packets) output that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter64  

hwEthPortStatOutPut128to255Bytes 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.5
The total number of packets (including bad packets) output that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter64  

hwEthPortStatOutPut256to511Bytes 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.6
The total number of packets (including bad packets) output that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets)..
OBJECT-TYPE    
  Counter64  

hwEthPortStatOutPut512to1023Bytes 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.7
The total number of packets (including bad packets) output that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter64  

hwEthPortStatOutPut1024to1518Bytes 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.8
The total number of packets (including bad packets) output that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter64  

hwEthPortStatOutPut1519toMaxBytes 1.3.6.1.4.1.2011.5.25.157.1.8.6.1.9
The total number of packets (including bad packets) output that were between 1519 and max length octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter64  

hwPhysicalPortGlobleCfg 1.3.6.1.4.1.2011.5.25.157.1.8.7
OBJECT IDENTIFIER    

hwLoopBackAutoClearEnable 1.3.6.1.4.1.2011.5.25.157.1.8.7.1
set loopback autoclear status enable(1) disable(2).
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwLoopBackAutoClearPeriod 1.3.6.1.4.1.2011.5.25.157.1.8.7.2
set loopback autoclear period, unit minute,value range<1-2880> default<5 minute>.
OBJECT-TYPE    
  Integer32 1..2880  

hwPortAlarmInverseEnable 1.3.6.1.4.1.2011.5.25.157.1.8.7.3
Config globle alarm inverse enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwDslGroup 1.3.6.1.4.1.2011.5.25.157.1.9
OBJECT IDENTIFIER    

hwDslGroupTable 1.3.6.1.4.1.2011.5.25.157.1.9.1
Indicates the attributes of the dsl group.
OBJECT-TYPE    
  SEQUENCE OF  
    HwDslGroupEntry

hwDslGroupEntry 1.3.6.1.4.1.2011.5.25.157.1.9.1.1
An entry in the dsl group table.
OBJECT-TYPE    
  HwDslGroupEntry  

hwDslGroupIfIndex 1.3.6.1.4.1.2011.5.25.157.1.9.1.1.1
Interface index(es) of dsl group present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwDslGroupWorkMode 1.3.6.1.4.1.2011.5.25.157.1.9.1.1.2
The dsl group of SHD4 card can work in efm or atm mode. Default is efm.
OBJECT-TYPE    
  INTEGER atm(1), efm(2)  

hwDslGroupBisState 1.3.6.1.4.1.2011.5.25.157.1.9.1.1.3
Bis can be enabled or disabled in ATM mode of SHD4 card.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), notSupport(3)  

hwDslGroupEncapeMode 1.3.6.1.4.1.2011.5.25.157.1.9.1.1.4
The dsl group of AVD8 card can work in ETHoA-LLC mode or ETHoA-VCMUX mode. Default is ETHoA-LLC.
OBJECT-TYPE    
  INTEGER eoaLlc(1), eoaVcmux(2), notSupport(3)  

hwDslGroupEnable 1.3.6.1.4.1.2011.5.25.157.1.9.1.1.5
Trigger the operation of binding dsl link(s) to the dsl group.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), notSupport(3)  

hwDslGroupRowStatus 1.3.6.1.4.1.2011.5.25.157.1.9.1.1.60
An object that allows entries in this table to be created, modified and deleted using the RowStatus convention. A SET operation to any other attribute in this row, when this object is set to 'active' (1), MUST be rejected with an SNMP error (e.g., inconsistentValue). In order to perform a SET operation to any other attribute in this table the manager MUST set this object to notInService (2). After setting the object back to 'active' the implementation MAY tear down all the sessions that belong to this partition and recreate them, depending on what session attributes have been modified.
OBJECT-TYPE    
  RowStatus  

hwDslGroupBoundVeTable 1.3.6.1.4.1.2011.5.25.157.1.9.2
Indicates the attributes of the dsl group bound virtual-ethernet.
OBJECT-TYPE    
  SEQUENCE OF  
    HwDslGroupBoundVeEntry

hwDslGroupBoundVeEntry 1.3.6.1.4.1.2011.5.25.157.1.9.2.1
An entry in the dsl group bound vitrual-ethernet table.
OBJECT-TYPE    
  HwDslGroupBoundVeEntry  

hwDslGroupIfIndexOfBound 1.3.6.1.4.1.2011.5.25.157.1.9.2.1.1
Interface index(es) of dsl group present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwVirtualEthernetIfIndex 1.3.6.1.4.1.2011.5.25.157.1.9.2.1.2
The first virtual ethernet interface which the dsl group is bound to.
OBJECT-TYPE    
  InterfaceIndex  

hwDslGroupVpi 1.3.6.1.4.1.2011.5.25.157.1.9.2.1.3
VPI value of the 1st PVC pair.
OBJECT-TYPE    
  Integer32 0..4095  

hwDslGroupVci 1.3.6.1.4.1.2011.5.25.157.1.9.2.1.4
VCI value of the 1st PVC pair.
OBJECT-TYPE    
  Integer32 0..65535  

hwDslGroupPvcId 1.3.6.1.4.1.2011.5.25.157.1.9.2.1.5
Identifier for VPI/VCI Pair.
OBJECT-TYPE    
  Integer32 1..2  

hwBoundVeRowStatus 1.3.6.1.4.1.2011.5.25.157.1.9.2.1.50
An object that allows entries in this table to be created, modified and deleted using the RowStatus convention. A SET operation to any other attribute in this row, when this object is set to 'active' (1), MUST be rejected with an SNMP error (e.g., inconsistentValue). In order to perform a SET operation to any other attribute in this table the manager MUST set this object to notInService (2). After setting the object back to 'active' the implementation MAY tear down all the sessions that belong to this partition and recreate them, depending on what session attributes have been modified.
OBJECT-TYPE    
  RowStatus  

hwDslGroupBindVeTable 1.3.6.1.4.1.2011.5.25.157.1.9.3
Indicates the relation of the dsl group binding virtual-ethernet.
OBJECT-TYPE    
  SEQUENCE OF  
    HwDslGroupBindVeEntry

hwDslGroupBindVeEntry 1.3.6.1.4.1.2011.5.25.157.1.9.3.1
An entry in the dsl group binding vitrual-ethernet table.
OBJECT-TYPE    
  HwDslGroupBindVeEntry  

hwDslGroupInterfaceIndex 1.3.6.1.4.1.2011.5.25.157.1.9.3.1.1
Interface index(es) of the dsl group present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwVirtualEthernetInterfaceIndex 1.3.6.1.4.1.2011.5.25.157.1.9.3.1.2
The virtual ethernet interface index which the dsl group is bound to.
OBJECT-TYPE    
  InterfaceIndex  

hwBindVeRowStatus 1.3.6.1.4.1.2011.5.25.157.1.9.3.1.50
An object that allows entries in this table to be created, modified and deleted using the RowStatus convention. A SET operation to any other attribute in this row, when this object is set to 'active' (1), MUST be rejected with an SNMP error (e.g., inconsistentValue). In order to perform a SET operation to any other attribute in this table the manager MUST set this object to notInService (2). After setting the object back to 'active' the implementation MAY tear down all the sessions that belong to this partition and recreate them, depending on what session attributes have been modified.
OBJECT-TYPE    
  RowStatus  

hwDslGroupIma 1.3.6.1.4.1.2011.5.25.157.1.10
OBJECT IDENTIFIER    

hwDslGroupImaTable 1.3.6.1.4.1.2011.5.25.157.1.10.1
Indicates the attributes of the dsl ima group.
OBJECT-TYPE    
  SEQUENCE OF  
    HwDslGroupImaEntry

hwDslGroupImaEntry 1.3.6.1.4.1.2011.5.25.157.1.10.1.1
An entry of the dsl ima group table.
OBJECT-TYPE    
  HwDslGroupImaEntry  

hwDslGroupImaIfIndex 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.1
Interface index(es) of dsl group present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwDslGroupImaVersion 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.2
Version of the ima group of SHD4I card. v0: ima protocol version 1.0; v1: ima protocol version 1.1.
OBJECT-TYPE    
  INTEGER v0(1), v1(2)  

hwDslGroupImaFrameLen 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.3
Frame length of the ima group of SHD4I card. If ima protocol version is 1.0, the frame length is only 128.
OBJECT-TYPE    
  ImaFrameLength  

hwDslGroupImaReset 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.4
ima group reset for SHD4I card.
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hwDslGroupImaTxMinLinkNum 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.5
Minimum active links number by TX direction.
OBJECT-TYPE    
  Integer32 1..4  

hwDslGroupImaRxMinLinkNum 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.6
Minimum active links number by RX direction.
OBJECT-TYPE    
  Integer32 1..4  

hwDslGroupImaNeState 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.7
The current state of the near-end ima group.
OBJECT-TYPE    
  ImaGroupState  

hwDslGroupImaFeState 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.8
The current state of the far-end ima group.
OBJECT-TYPE    
  ImaGroupState  

hwDslGroupImaTxCellRate 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.9
The current cell rate of ima group by TX direction.
OBJECT-TYPE    
  Integer32  

hwDslGroupImaRxCellRate 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.10
The current cell rate of ima group by RX direction.
OBJECT-TYPE    
  Integer32  

hwDslGroupImaTxActLinkNum 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.11
Number of active links by TX direction.
OBJECT-TYPE    
  Integer32 0..4  

hwDslGroupImaRxActLinkNum 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.12
Number of active links by RX direction.
OBJECT-TYPE    
  Integer32 0..4  

hwDslGroupImaIfName 1.3.6.1.4.1.2011.5.25.157.1.10.1.1.13
The interface name of ima group.
OBJECT-TYPE    
  STRING  


hwDslLinkTable 1.3.6.1.4.1.2011.5.25.157.1.11.1
Indicates the dsl link bound relation.
OBJECT-TYPE    
  SEQUENCE OF  
    HwDslLinkEntry

hwDslLinkEntry 1.3.6.1.4.1.2011.5.25.157.1.11.1.1
An entry of the dsl link bound relation.
OBJECT-TYPE    
  HwDslLinkEntry  

hwBoundDslGroupIfIndex 1.3.6.1.4.1.2011.5.25.157.1.11.1.1.1
Interface index of dsl group which the dsl link bound to.
OBJECT-TYPE    
  InterfaceIndex  

hwDslLinkIfIndex 1.3.6.1.4.1.2011.5.25.157.1.11.1.1.2
Interface index of the dsl link device.
OBJECT-TYPE    
  InterfaceIndex  

hwDslLinkIfName 1.3.6.1.4.1.2011.5.25.157.1.11.1.1.4
The interface name of the dsl link.
OBJECT-TYPE    
  STRING  

hwBoundDslGroupIfName 1.3.6.1.4.1.2011.5.25.157.1.11.1.1.5
Interface index of dsl group which the dsl link bound to.
OBJECT-TYPE    
  STRING  

hwDslLinkBoundRowStatus 1.3.6.1.4.1.2011.5.25.157.1.11.1.1.50
An object that allows entries in this table to be created, modified and deleted using the RowStatus convention. A SET operation to any other attribute in this row, when this object is set to 'active' (1), MUST be rejected with an SNMP error (e.g., inconsistentValue). In order to perform a SET operation to any other attribute in this table the manager MUST set this object to notInService (2). After setting the object back to 'active' the implementation MAY tear down all the sessions that belong to this partition and recreate them, depending on what session attributes have been modified.
OBJECT-TYPE    
  RowStatus  

hwPWAlarm 1.3.6.1.4.1.2011.5.25.157.1.12
OBJECT IDENTIFIER    

hwPWAlarmTable 1.3.6.1.4.1.2011.5.25.157.1.12.1
Indicates the attributes of the PW alarm.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPWAlarmEntry

hwPWAlarmEntry 1.3.6.1.4.1.2011.5.25.157.1.12.1.1
An entry of the PW alarm relation.
OBJECT-TYPE    
  HwPWAlarmEntry  

hwPWAlarmIfIndex 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.1
Interface index of PW alarm group.
OBJECT-TYPE    
  InterfaceIndex  

hwPWCesVcID 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.2
Vc ID of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwPWCesVcType 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.3
Vc Type of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwPeerIpAddr 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.4
Peer IP Address of PW alarm group.
OBJECT-TYPE    
  IpAddress  

hwAlarmStatus 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.5
Alarm status of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwPWAlarmRMLEnableStatus 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.6
PW control word RML of PW alarm group.
OBJECT-TYPE    
  EnabledStatus  

hwLosAlarmTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.7
Trigger Threshold of continuous loss packets of PW alarm group.
OBJECT-TYPE    
  Integer32 2..65535  

hwLosAlarmResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.8
Resume Threshold of continuous loss packets of PW alarm group.
OBJECT-TYPE    
  Integer32 32..65535  

hwPWPortName 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.9
PW port name of PW alarm group.
OBJECT-TYPE    
  STRING  

hwLosPktExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.10
Trigger threshold of lost packets of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwLosPktExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.11
Resume threshold of lost packets of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwMisorderPktExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.12
Trigger threshold of packets lost due to the out-of-order condition of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwMisorderPktExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.13
Resume threshold of packets lost due to the out-of-order condition of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwStrayPktExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.14
Trigger threshold of misconnected packets of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwStrayPktExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.15
Resume threshold of misconnected packets of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwMalPktExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.16
Trigger threshold of malformed packets of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwMalPktExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.17
Resume threshold of malformed packets of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwJtrUdrExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.18
Trigger threshold of jitter buffer underflows of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwJtrUdrExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.19
Resume threshold of jitter buffer underflows of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwJtrOvrExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.20
Trigger threshold of jitter buffer overflows of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwJtrOvrExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.1.1.21
Resume threshold of jitter buffer overflows of PW alarm group.
OBJECT-TYPE    
  Integer32  

hwAtmPWAlarmTable 1.3.6.1.4.1.2011.5.25.157.1.12.2
Indicates the attributes of the ATM PW alarm.
OBJECT-TYPE    
  SEQUENCE OF  
    HwAtmPWAlarmEntry

hwAtmPWAlarmEntry 1.3.6.1.4.1.2011.5.25.157.1.12.2.1
An entry of the ATM PW alarm relation.
OBJECT-TYPE    
  HwAtmPWAlarmEntry  

hwAtmPWAlarmIfIndex 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.1
Interface index of ATM PW alarm group.
OBJECT-TYPE    
  InterfaceIndex  

hwAtmVcID 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.2
Vc ID of ATM PW alarm group.
OBJECT-TYPE    
  Integer32  

hwAtmVcType 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.3
Vc Type of ATM PW alarm group.
OBJECT-TYPE    
  Integer32  

hwAtmPeerIpAddr 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.4
Peer IP Address of ATM PW alarm group.
OBJECT-TYPE    
  IpAddress  

hwAtmPWPortName 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.5
ATM PW port name of PW alarm group.
OBJECT-TYPE    
  STRING  

hwAtmLosPktExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.6
Trigger threshold of lost packets of ATM PW alarm group.
OBJECT-TYPE    
  Integer32 1..1000  

hwAtmLosPktExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.7
Resume threshold of lost packets of ATM PW alarm group.
OBJECT-TYPE    
  Integer32 1..1000  

hwAtmMisorderPktExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.8
Trigger threshold of packets lost due to the out-of-order condition of ATM PW alarm group.
OBJECT-TYPE    
  Integer32 1..1000  

hwAtmMisorderPktExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.9
Resume threshold of packets lost due to the out-of-order condition of ATM PW alarm group.
OBJECT-TYPE    
  Integer32 1..1000  

hwAtmUnknownCellExcTriggerThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.10
Trigger threshold of unknown cell of ATM PW alarm group.
OBJECT-TYPE    
  Integer32 1..1000  

hwAtmUnknownCellExcResumeThreshold 1.3.6.1.4.1.2011.5.25.157.1.12.2.1.11
Resume threshold of unknown cell of ATM PW alarm group.
OBJECT-TYPE    
  Integer32 1..1000  

hwSNMPTrapEn 1.3.6.1.4.1.2011.5.25.157.1.13
OBJECT IDENTIFIER    

hwSNMPTrapEnTable 1.3.6.1.4.1.2011.5.25.157.1.13.1
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  SEQUENCE OF  
    HwSNMPTrapEnEntry

hwSNMPTrapEnEntry 1.3.6.1.4.1.2011.5.25.157.1.13.1.1
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  HwSNMPTrapEnEntry  

hwSNMPTrapEnIfIndex 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.1
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  InterfaceIndex  

hwCesPWLopsEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.2
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWRemoteLosPktEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.3
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWOppositeRAIEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.4
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWOppositeAcfaultEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.5
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWLosPktEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.6
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWMisorderPktEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.7
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWStrayPktEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.8
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWMalPktEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.9
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWJtrUnrEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.10
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWJtrOvrEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.11
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwCesPWAllEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.12
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwPhysicalPortLosAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.13
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwPhysicalPortLofAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.14
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwRsOofAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.15
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwRsB1ExcAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.16
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwRsB1SdAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.17
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwRsJ0TimAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.18
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwMsRdiAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.19
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwMsB2ExcAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.20
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwMsAuLopAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.21
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwMsAisAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.22
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwMsB2SdAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.23
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwHpJ1TimAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.24
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwHpUneqAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.25
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwHpRdiAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.26
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwHpB3ExcAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.27
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwHpPlmAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.28
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwHpB3SdAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.29
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwHpAuAisAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.30
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpTuLopAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.31
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwHpTuLomAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.32
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpTimAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.33
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpUneqAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.34
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpRdiAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.35
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpBipExcAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.36
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpBipSdAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.37
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpPlmAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.38
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpTuAisAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.39
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwDs1EsExcAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.40
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwDs1RmfaAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.41
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwDs1LmfaAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.42
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwDs1AisAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.43
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwDs1RdiAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.44
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwRsLocAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.45
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpRfiAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.46
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLpV5VcaisAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.47
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwVc12oofAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.48
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwVc12AlmE1RaiAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.49
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwVc12LfaAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.50
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwVc12UpE1AisAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.51
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwVc12DownE1AisAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.52
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwDs1DownE1AisAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.53
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwMsLpsUniBiMAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.54
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwMsK1K2MAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.55
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwMsK2MAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.56
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwVc12LmfaAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.57
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwSDHAllEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.58
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLaserShutAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.59
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLaserAutoShutAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.60
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLaserAllEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.61
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLoopbackAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.62
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwChannelLoopbackAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.63
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwLoopbackAllEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.64
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwAtmOcdAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.65
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwAtmLcdAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.66
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwAtmUhcsAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.67
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwAtmChcsAlarmEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.68
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwAtmPWLosPktEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.69
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwAtmPWMisorderPktEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.70
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwAtmPWUnknownCellEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.71
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwAtmAllEn 1.3.6.1.4.1.2011.5.25.157.1.13.1.1.72
Reserved nodes do not support this function temporarily.
OBJECT-TYPE    
  Integer32  

hwPortAlarmThreshold 1.3.6.1.4.1.2011.5.25.157.1.14
OBJECT IDENTIFIER    

hwPortAlarmThresholdTable 1.3.6.1.4.1.2011.5.25.157.1.14.1
Indicates the port alarm threshold. This table lists the port alarm threshold of various interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortAlarmThresholdEntry

hwPortAlarmThresholdEntry 1.3.6.1.4.1.2011.5.25.157.1.14.1.1
Indicates the port alarm threshold. This table lists the threshold of various port alarm.
OBJECT-TYPE    
  HwPortAlarmThresholdEntry  

hwPhysicalPortThrIfIndex 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.1
Interface index(es) of physical port(s) present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwPhysicalPortThrName 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.2
Interface name of physical port(s) present on the device.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPhysicalPortCrcErrorStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.3
Crc error statistics value.
OBJECT-TYPE    
  Counter64  

hwPhysicalPortCrcErrorHighThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.4
Crc error alarm high threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortCrcErrorLowThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.5
Crc error alarm low threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortCrcErrorInterval 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.6
Crc error alarm interval time(unit is second),default value is 10s.
OBJECT-TYPE    
  Unsigned32 1..65535  

hwPhysicalPortSymbolErrorStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.7
Symbol error statistics value.
OBJECT-TYPE    
  Counter64  

hwPhysicalPortSymbolErrorHighThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.8
Symbol error alarm high threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortSymbolErrorLowThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.9
Symbol error alarm low threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortSymbolErrorInterval 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.10
Symbol error alarm interval time(unit is second),default value is 10s.
OBJECT-TYPE    
  Unsigned32 1..65535  

hwPhysicalPortInputErrorStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.11
Input error statistics value.
OBJECT-TYPE    
  Counter64  

hwPhysicalPortInputErrorHighThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.12
Input error alarm high threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortInputErrorLowThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.13
Input error alarm low threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortInputErrorInterval 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.14
Input error alarm interval time(unit is second),default value is 10s.
OBJECT-TYPE    
  Unsigned32 1..65535  

hwPhysicalPortOutputErrorStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.15
Output error statistics value.
OBJECT-TYPE    
  Counter64  

hwPhysicalPortOutputErrorHighThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.16
Output error alarm high threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortOutputErrorLowThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.17
Output error alarm low threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortOutputErrorInterval 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.18
Output error alarm interval time(unit is second),default value is 10s.
OBJECT-TYPE    
  Unsigned32 1..65535  

hwPhysicalPortSdhErrorStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.19
Sdh error statistics value.
OBJECT-TYPE    
  Counter64  

hwPhysicalPortSdhErrorHighThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.20
Sdh error alarm high threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortSdhErrorLowThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.21
Sdh error alarm low threshold,default value is 3.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPhysicalPortSdhErrorInterval 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.22
Sdh error alarm interval time(unit is second),default value is 10s.
OBJECT-TYPE    
  Unsigned32 1..65535  

hwPhysicalPortBIP8SDErrorThreshold 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.23
BIP8-SD error alarm threshold,default value is 6.
OBJECT-TYPE    
  Unsigned32 6..9  

hwPhysicalPortCrcPerAlarmThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.24
The coefficient value of CRC-PER(Packet Error Ratio) alarm threshold. The range is 1 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerAlarmThresholdPower 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.25
The power value of CRC-PER(Packet Error Ratio) alarm threshold. The range is 1 to 7.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerResumeThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.26
The coefficient value of CRC-PER(Packet Error Ratio) resume threshold. The range is 1 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerResumeThresholdPower 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.27
The power value of CRC-PER(Packet Error Ratio) resume threshold. The range is 1 to 7.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerTriggerLsp 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.28
Enable or disable the CRC-PER(Packet Error Ratio) result in switchover. The range is 0 to 2. The value 0 means switchover is disabled; 1 means only the lsp switchover is enabled; 2 means only the section switchover is enabled.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerCurrentValueString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.29
The current value of CRC-PER(Packet Error Ratio).
OBJECT-TYPE    
  STRING  

hwPhysicalPortCrcPerAlarmThresholdString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.30
The alarm threshold of CRC-PER(Packet Error Ratio).
OBJECT-TYPE    
  STRING  

hwPhysicalPortCrcPerResumeThresholdString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.31
The resume threshold of CRC-PER(Packet Error Ratio).
OBJECT-TYPE    
  STRING  

hwPhysicalPortCrcPerTriggerSection 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.32
The trigger section of CRC-PER(Packet Error Ratio).
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortAlarmTypeThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.33
The value 0 means high-low packet error is enabled; 1 means CRC-PER(Packet Error Ratio) is enabled; 2 means CRC-BER(Bit Error Ratio) is enabled.
OBJECT-TYPE    
  INTEGER packeterror(0), packeterrorratio(1), biterrorratio(2)  

hwPhysicalPortCrcSdAlarmThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.34
The coefficient value of MAC_FCS_SD alarm threshold. The range is 1 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcSdAlarmThresholdPower 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.35
The power value of MAC_FCS_SD alarm threshold. The range is 5 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcSdResumeThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.36
The coefficient value of MAC_FCS_SD resume threshold. The range is 1 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcSdResumeThresholdPower 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.37
The power value of MAC_FCS_SD resume threshold. The range is 5 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcExcAlarmThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.38
The coefficient value of MAC_FCS_EXC alarm threshold. The range is 1 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcExcAlarmThresholdPower 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.39
The power value of MAC_FCS_EXC alarm threshold. The range is 2 to 5.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcExcResumeThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.40
The coefficient value of MAC_FCS_EXC resume threshold. The range is 1 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcExcResumeThresholdPower 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.41
The power value of MAC_FCS_EXC resume threshold. The range is 2 to 5.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcSdAlarmThresholdString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.42
The alarm threshold of MAC_FCS_SD.
OBJECT-TYPE    
  STRING  

hwPhysicalPortCrcSdResumeThresholdString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.43
The resume threshold of MAC_FCS_SD.
OBJECT-TYPE    
  STRING  

hwPhysicalPortCrcExcAlarmThresholdString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.44
The alarm threshold of MAC_FCS_EXC.
OBJECT-TYPE    
  STRING  

hwPhysicalPortCrcExcResumeThresholdString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.45
The resume threshold of MAC_FCS_EXC.
OBJECT-TYPE    
  STRING  

hwPhysicalPortCrcPerAlarmCoefficientStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.46
The coefficient value of CRC-PER(Packet Error Ratio) alarm statistics.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerAlarmPowerStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.47
The power value of CRC-PER(Packet Error Ratio) alarm statistics.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcSdAlarmTriggerLsp 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.48
Enable or disable the SD alarm result in switchover. The value -1 means do not support switchover;1 means the lsp switchover is enabled; 2 means switchover is disabled.
OBJECT-TYPE    
  INTEGER notsupport(-1), enable(1), disable(2)  

hwPhysicalPortCrcExcAlarmTriggerLsp 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.49
Enable or disable the EXC alarm result in switchover. The value -1 means do not support switchover;1 means the lsp switchover is enabled; 2 means switchover is disabled.
OBJECT-TYPE    
  INTEGER notsupport(-1), enable(1), disable(2)  

hwPhysicalPortCrcPerWarningThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.50
The coefficient value of CRC-PER(Packet Error Ratio) warning threshold. The range is 1 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerWarningThresholdPower 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.51
The power value of CRC-PER(Packet Error Ratio) warning threshold. The range is 1 to 7.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerWarningResumeThresholdCoefficient 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.52
The coefficient value of CRC-PER(Packet Error Ratio) warning resume threshold. The range is 1 to 9.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerWarningResumeThresholdPower 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.53
The power value of CRC-PER(Packet Error Ratio) warning resume threshold. The range is 1 to 7.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortCrcPerWarningThresholdString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.54
The warning threshold of CRC-PER(Packet Error Ratio).
OBJECT-TYPE    
  STRING  

hwPhysicalPortCrcPerWarningResumeThresholdString 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.55
The warning resume threshold of CRC-PER(Packet Error Ratio).
OBJECT-TYPE    
  STRING  

hwPhysicalPortPreFecCoefficientStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.56
The coefficient value of PRE-FEC bit-error-ratio statistics.
OBJECT-TYPE    
  Unsigned32  

hwPhysicalPortPreFecPowerStatistics 1.3.6.1.4.1.2011.5.25.157.1.14.1.1.57
The power value of PRE-FEC bit-error-ratio statistics.
OBJECT-TYPE    
  Unsigned32  

hwPortAlarmDownEnable 1.3.6.1.4.1.2011.5.25.157.1.15
OBJECT IDENTIFIER    

hwPortAlarmDownEnableTable 1.3.6.1.4.1.2011.5.25.157.1.15.1
Enalbe or disable the port alarm result in physics down. This table lists the enable status of various port alarm.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortAlarmDownEnableEntry

hwPortAlarmDownEnableEntry 1.3.6.1.4.1.2011.5.25.157.1.15.1.1
Enalbe or disable the port alarm result in physics down. This table lists the enable status of various port alarm.
OBJECT-TYPE    
  HwPortAlarmDownEnableEntry  

hwPhysicalPortDownIfIndex 1.3.6.1.4.1.2011.5.25.157.1.15.1.1.1
Interface index(es) of physical port(s) present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwPhysicalPortDownName 1.3.6.1.4.1.2011.5.25.157.1.15.1.1.2
Interface name of physical port(s) present on the device.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPhysicalPortCrcEnabledDown 1.3.6.1.4.1.2011.5.25.157.1.15.1.1.3
Enalbe or disable the crc error alarm result in physics down, and the default value is disable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hwPhysicalPortSymbolEnabledDown 1.3.6.1.4.1.2011.5.25.157.1.15.1.1.4
Enalbe or disable the symbol error alarm result in physics down, and the default value is disable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hwPhysicalPortInputEnabledDown 1.3.6.1.4.1.2011.5.25.157.1.15.1.1.5
Enalbe or disable the input error alarm result in physics down, and the default value is disable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hwPhysicalPortOutputEnabledDown 1.3.6.1.4.1.2011.5.25.157.1.15.1.1.6
Enalbe or disable the output error alarm result in physics down, and the default value is disable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hwPhysicalPortSdhEnabledDown 1.3.6.1.4.1.2011.5.25.157.1.15.1.1.7
Enalbe or disable the sdh error alarm result in physics down, and the default value is disable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hwPhysicalPortBip8SdEnabledDown 1.3.6.1.4.1.2011.5.25.157.1.15.1.1.8
Enalbe or disable the BIP8-SD error alarm result in physics down, and the default value is disable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hwPortProtectGroupCfg 1.3.6.1.4.1.2011.5.25.157.1.16
OBJECT IDENTIFIER    

hwPortProtectGroupCfgTable 1.3.6.1.4.1.2011.5.25.157.1.16.1
The table includes the information of the port protect group configuration information, and include the port group, working status of port etc.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortProtectGroupCfgEntry

hwPortProtectGroupCfgEntry 1.3.6.1.4.1.2011.5.25.157.1.16.1.1
The table includes the information of the port protect group configuration information. The index of the table is hwPortProtectGroupId.
OBJECT-TYPE    
  HwPortProtectGroupCfgEntry  

hwPortProtectGroupId 1.3.6.1.4.1.2011.5.25.157.1.16.1.1.1
Port protect group index.
OBJECT-TYPE    
  Integer32 0..127  

hwPortProtectMasterIfIndex 1.3.6.1.4.1.2011.5.25.157.1.16.1.1.2
The master interface index of port protect group.
OBJECT-TYPE    
  Integer32  

hwPortProtectMasterStatus 1.3.6.1.4.1.2011.5.25.157.1.16.1.1.3
Working status of master port , include work, protect, down. work: the port in group is active. protect: master port is protect port. down: master port is inactive.
OBJECT-TYPE    
  INTEGER work(1), protect(2), down(3)  

hwPortProtectSlaveIfIndex 1.3.6.1.4.1.2011.5.25.157.1.16.1.1.4
The slave interface index of port protect group.
OBJECT-TYPE    
  Integer32  

hwPortProtectSlaveStatus 1.3.6.1.4.1.2011.5.25.157.1.16.1.1.5
Working status of slave port , include work, protect, down. work: the port in group is active. protect: slave port is protect port. down: slave port is inactive.
OBJECT-TYPE    
  INTEGER work(1), protect(2), down(3)  

hwPortProtectRowStatus 1.3.6.1.4.1.2011.5.25.157.1.16.1.1.6
Status of port protect group row.
OBJECT-TYPE    
  RowStatus  

hwPortLine 1.3.6.1.4.1.2011.5.25.157.1.17
OBJECT IDENTIFIER    

hwPortLineTable 1.3.6.1.4.1.2011.5.25.157.1.17.1
Indicates the link attributes of the interface. This table lists the link attributes of the interface.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortLineEntry

hwPortLineEntry 1.3.6.1.4.1.2011.5.25.157.1.17.1.1
Indicates the link attributes of the interface. This table lists the link attributes of the interface.
OBJECT-TYPE    
  HwPortLineEntry  

hwPortLineIfIndex 1.3.6.1.4.1.2011.5.25.157.1.17.1.1.1
Interface index(es) of port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwPortLineUpStreampbo 1.3.6.1.4.1.2011.5.25.157.1.17.1.1.2
Indicates the upstream power back-off of the interface.
OBJECT-TYPE    
  Integer32  

hwPortLineDownStreampbo 1.3.6.1.4.1.2011.5.25.157.1.17.1.1.3
Indicates the downstream power back-off of the interface.
OBJECT-TYPE    
  Integer32  

hwPortLineUpStreamLoopAtten 1.3.6.1.4.1.2011.5.25.157.1.17.1.1.4
Indicates the upstream loopback attenuation of the interface.
OBJECT-TYPE    
  Integer32  

hwPortLineDownStreamLoopAtten 1.3.6.1.4.1.2011.5.25.157.1.17.1.1.5
Indicates the downstream loopback attenuation of the interface.
OBJECT-TYPE    
  Integer32  

hwPortLineUpStreamSnrMargin 1.3.6.1.4.1.2011.5.25.157.1.17.1.1.6
Indicates the upstream SNR margin of the interface.
OBJECT-TYPE    
  Integer32  

hwPortLineDownStreamSnrMargin 1.3.6.1.4.1.2011.5.25.157.1.17.1.1.7
Indicates the downstream SNR margin of the interface.
OBJECT-TYPE    
  Integer32  

hwPortLineSpeed 1.3.6.1.4.1.2011.5.25.157.1.17.1.1.8
Indicates the negotiated rate of the interface.
OBJECT-TYPE    
  Integer32  

hwPortIfStatistics 1.3.6.1.4.1.2011.5.25.157.1.18
OBJECT IDENTIFIER    

hwPortIfStatTable 1.3.6.1.4.1.2011.5.25.157.1.18.1
This table lists the number of packets of the interface.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortIfStatEntry

hwPortIfStatEntry 1.3.6.1.4.1.2011.5.25.157.1.18.1.1
This table lists the number of packets of the interface.
OBJECT-TYPE    
  HwPortIfStatEntry  

hwPortIfStatIfIndex 1.3.6.1.4.1.2011.5.25.157.1.18.1.1.1
Interface index(es) of port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwPortIfStatIfInCrcPkts 1.3.6.1.4.1.2011.5.25.157.1.18.1.1.2
Indicates the number of packets which the CRC operates.
OBJECT-TYPE    
  Integer32  

hwPortDescription 1.3.6.1.4.1.2011.5.25.157.1.19
OBJECT IDENTIFIER    

hwPortDescriptionTable 1.3.6.1.4.1.2011.5.25.157.1.19.1
This table lists the description of interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortDescriptionEntry

hwPortDescriptionEntry 1.3.6.1.4.1.2011.5.25.157.1.19.1.1
This table lists the description of interfaces.
OBJECT-TYPE    
  HwPortDescriptionEntry  

hwPortDescriptionIfIndex 1.3.6.1.4.1.2011.5.25.157.1.19.1.1.1
Interface index(es) of port(s) present on the device.
OBJECT-TYPE    
  Integer32  

hwPortDescriptionIfPortDescription 1.3.6.1.4.1.2011.5.25.157.1.19.1.1.2
Indicates the description of ports.
OBJECT-TYPE    
  INTEGER router(1), switch(2), phone(3), desktop(4), null(5)  

hwPRBSTestInfo 1.3.6.1.4.1.2011.5.25.157.1.20
OBJECT IDENTIFIER    

hwPRBSTestPortStatusTable 1.3.6.1.4.1.2011.5.25.157.1.20.1
This table lists the capability and result of PRBS test.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPRBSTestPortStatusEntry

hwPRBSTestPortStatusEntry 1.3.6.1.4.1.2011.5.25.157.1.20.1.1
This table lists the capability and result of PRBS test.
OBJECT-TYPE    
  HwPRBSTestPortStatusEntry  

hwPRBSTestPortStatusIfName 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.1
Interface name of port(s) present on the device.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPRBSTestPortStatusSide 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.2
Indicate PRBS test side.
OBJECT-TYPE    
  INTEGER nni(0), uni(1)  

hwPRBSTestPortStatusSuportFlag 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.3
Whether PRBS test supported.
OBJECT-TYPE    
  INTEGER notsupportinter(0), unframedandsupport(1), unframedandnotsupport(2), fractionalandsupport(3), fractionalandnotsupport(4)  

hwPRBSTestPortStatusPatternBitmap 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.4
Indicate supported PRBS pattern by bitmap. bit 0 - 3 : PRBS15, PRBS20, PRBS23, QRSS, bit 4 - 7 : 0S, 1S, ALT-0-1, 1IN8, bit 8 - 11 : 3IN24, PRBS6, PRBS9, PRBS11, bit 12 : QRW
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestPortStatusErrInsertLevel 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.5
Indicate the supported err-insert level. It's described by bitmap. From low to high, the different bit position indicates whether or not support 1, 1e-1, 1e-2, 1e-3, etc. e.g. 0x1FC (0b111111100): Range from 1e-2 to 1e-8 supported. 0xA (0b1010) : Only 1e-1 and 1e-3 supported.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestPortStatusSlotNum 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.6
Slot ID of the testing phyicial port.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestPortStatusCardNum 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.7
Card ID of the testing phyicial port.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestPortStatusPhyPortIfName 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.8
Interface Name of the testing phyicial port.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPRBSTestPortStatusResultCount 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.9
Total count of PRBS test history result.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestPortStatusOngoingTestIndex 1.3.6.1.4.1.2011.5.25.157.1.20.1.1.10
Indicate the ongoing PRBS testing index of current interface.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultTable 1.3.6.1.4.1.2011.5.25.157.1.20.2
This table lists PRBS test result info.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPRBSTestResultEntry

hwPRBSTestResultEntry 1.3.6.1.4.1.2011.5.25.157.1.20.2.1
This table lists PRBS test result info.
OBJECT-TYPE    
  HwPRBSTestResultEntry  

hwPRBSTestResultIfName 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.1
Interface name of port(s) present on the device.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPRBSTestResultTestIndex 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.2
Indicate the PRBS test hisotry test index. 0 is invalid.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultPhyPortIfName 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.3
Interface Name of the testing phyicial port.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPRBSTestResultSide 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.4
Indicate PRBS test side.
OBJECT-TYPE    
  INTEGER nni(0), uni(1)  

hwPRBSTestResultPattern 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.5
Indicate PRBS pattern. Refer to hwPRBSTestPortStatusPatternBitmap, but single bit here.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultIntervalTime 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.6
Period time of each interval, in second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultIntervalCount 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.7
PRBS test interval repeat count.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultTestingIntervalIndex 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.8
Indicate the ongoing testing interval index.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultStartTime 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.9
Start time of the test.
OBJECT-TYPE    
  DateAndTime  

hwPRBSTestResultStopTime 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.10
Stop time of the test.
OBJECT-TYPE    
  DateAndTime  

hwPRBSTestResultProgress 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.11
Prgress of the test. 100 means 100%.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultRemainTime 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.12
Remaining time of the test, in second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultErrInserted 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.13
Whether error-bit inserted of the test
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

hwPRBSTestResultTotalBit 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.14
Total-bit of the test.
OBJECT-TYPE    
  Counter64  

hwPRBSTestResultErrorBit 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.15
Error-bit of the test.
OBJECT-TYPE    
  Counter64  

hwPRBSTestResultBerCoe 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.16
The coefficient value of bit-error-ratio.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultBerPow 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.17
The power value of bit-error-ratio.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultLos 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.18
Loss of sync second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultEs 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.19
Error second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultEfs 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.20
Error free second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultSes 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.21
Severely error second, comparing with 1E-3.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultUas 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.22
Unavaliable seconds. Continuous severely error seconds, start counting with the 11th SES.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultSegmentTime 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.23
Period time of each segment, in second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultSegmentTotalCount 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.24
Segment count of the whole PRBS test.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestResultTestingSegmentIndex 1.3.6.1.4.1.2011.5.25.157.1.20.2.1.25
Indicate the ongoing testing segment index.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalTable 1.3.6.1.4.1.2011.5.25.157.1.20.3
This table lists PRBS test interval info.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPRBSTestIntervalEntry

hwPRBSTestIntervalEntry 1.3.6.1.4.1.2011.5.25.157.1.20.3.1
This table lists PRBS test interval info.
OBJECT-TYPE    
  HwPRBSTestIntervalEntry  

hwPRBSTestIntervalIfName 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.1
Interface name of port(s) present on the device.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPRBSTestIntervalTestIndex 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.2
Indicate the PRBS test hisotry test index. 0 is invalid.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalIndex 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.3
Indicate the interval index of a test. 0 is invalid.
OBJECT-TYPE    
  Unsigned32 0..60  

hwPRBSTestIntervalStartTime 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.4
Start time of the interval.
OBJECT-TYPE    
  DateAndTime  

hwPRBSTestIntervalStopTime 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.5
Stop time of the interval
OBJECT-TYPE    
  DateAndTime  

hwPRBSTestIntervalProgress 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.6
Prgress of the interval. 100 means 100%.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalRemainTime 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.7
Remaining time of the interval, in second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalErrInserted 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.8
Whether error-bit inserted of the interval
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

hwPRBSTestIntervalTotalBit 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.9
Total-bit of the interval.
OBJECT-TYPE    
  Counter64  

hwPRBSTestIntervalErrorBit 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.10
Error-bit of the interval.
OBJECT-TYPE    
  Counter64  

hwPRBSTestIntervalBerCoe 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.11
The coefficient value of bit-error-ratio.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalBerPow 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.12
The power value of bit-error-ratio.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalLos 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.13
Loss of sync second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalEs 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.14
Error second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalEfs 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.15
Error free second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalSes 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.16
Severely error second, comparing with 1E-3.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestIntervalUas 1.3.6.1.4.1.2011.5.25.157.1.20.3.1.17
Unavaliable seconds. Continuous severely error seconds, start counting with the 11th SES.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestSegmentTable 1.3.6.1.4.1.2011.5.25.157.1.20.4
This table lists PRBS test segment info.
OBJECT-TYPE    
  SEQUENCE OF  
    HwPRBSTestSegmentEntry

hwPRBSTestSegmentEntry 1.3.6.1.4.1.2011.5.25.157.1.20.4.1
This table lists PRBS test segment info.
OBJECT-TYPE    
  HwPRBSTestSegmentEntry  

hwPRBSTestSegmentIfName 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.1
Interface name of port(s) present on the device.
OBJECT-TYPE    
  STRING Size(0..64)  

hwPRBSTestSegmentTestIndex 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.2
Indicate the PRBS test index. 0 is invalid.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestSegmentIndex 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.3
Indicate the segment index of a test. 0 is invalid.
OBJECT-TYPE    
  Unsigned32 0..864000  

hwPRBSTestSegmentStartTime 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.4
Start time of the interval.
OBJECT-TYPE    
  DateAndTime  

hwPRBSTestSegmentEndTime 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.5
Stop time of the interval
OBJECT-TYPE    
  DateAndTime  

hwPRBSTestSegmentTotalBit 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.6
Total-bit of the segment.
OBJECT-TYPE    
  Counter64  

hwPRBSTestSegmentErrorBit 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.7
Error-bit of the segment.
OBJECT-TYPE    
  Counter64  

hwPRBSTestSegmentBerCoe 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.8
The coefficient value of bit-error-ratio.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestSegmentBerPow 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.9
The power value of bit-error-ratio.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestSegmentLos 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.10
Loss of sync second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestSegmentEs 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.11
Error second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestSegmentEfs 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.12
Error free second.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestSegmentSes 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.13
Severely error second, comparing with 1E-3.
OBJECT-TYPE    
  Unsigned32  

hwPRBSTestSegmentUas 1.3.6.1.4.1.2011.5.25.157.1.20.4.1.14
Unavaliable seconds. Continuous severely error seconds, start counting with the 11th SES.
OBJECT-TYPE    
  Unsigned32  

hwOtn 1.3.6.1.4.1.2011.5.25.157.1.21
OBJECT IDENTIFIER    

hwOtnTable 1.3.6.1.4.1.2011.5.25.157.1.21.1
Indicates the otn attributes of the WDM interface.
OBJECT-TYPE    
  SEQUENCE OF  
    HwOtnEntry

hwOtnEntry 1.3.6.1.4.1.2011.5.25.157.1.21.1.1
This table lists the otn attributes of the WDM interface.
OBJECT-TYPE    
  HwOtnEntry  

hwOtnIfIndex 1.3.6.1.4.1.2011.5.25.157.1.21.1.1.1
Interface index(es) of port(s) present on the device.
OBJECT-TYPE    
  InterfaceIndex  

hwOtnFecMode 1.3.6.1.4.1.2011.5.25.157.1.21.1.1.2
Indicates the Fec mode of the WDM interface. By default, the Fec mode is standard.
OBJECT-TYPE    
  INTEGER standard(1), enhanced(2), enhancedI4(3), enhancedI7(4), huaweiMode(5), disable(255)  

hwLogicalPort 1.3.6.1.4.1.2011.5.25.157.1.22
OBJECT IDENTIFIER    

hwLogicalPortTable 1.3.6.1.4.1.2011.5.25.157.1.22.1
This table lists the working status of the logical ports.
OBJECT-TYPE    
  SEQUENCE OF  
    HwLogicalPortEntry

hwLogicalPortEntry 1.3.6.1.4.1.2011.5.25.157.1.22.1.1
This table lists the working status of the logical ports.
OBJECT-TYPE    
  HwLogicalPortEntry  

hwLogicalPortIfIndex 1.3.6.1.4.1.2011.5.25.157.1.22.1.1.1
Interface index(es) of the logical port(s) present on the device .
OBJECT-TYPE    
  InterfaceIndex  

hwLogicalPortStatisticEnable 1.3.6.1.4.1.2011.5.25.157.1.22.1.1.2
Indicates the statistic enable status of the logical port(s) .
OBJECT-TYPE    
  INTEGER neither(1), inbound(2), outbound(3), both(4)  

hwPortNotifications 1.3.6.1.4.1.2011.5.25.157.2
OBJECT IDENTIFIER    

hwPortACRMasterPWChange 1.3.6.1.4.1.2011.5.25.157.2.1
CES-ACR master PW change notification,indicates master pw change or master pw status change,this may happen when a pw is deleted or the pw status change.
NOTIFICATION-TYPE    

hwDslImaGroupTraps 1.3.6.1.4.1.2011.5.25.157.2.2
OBJECT IDENTIFIER    

hwDslImaGroupLEDown 1.3.6.1.4.1.2011.5.25.157.2.2.1
The ima group local edge down notification.
NOTIFICATION-TYPE    

hwDslImaGroupLEUp 1.3.6.1.4.1.2011.5.25.157.2.2.2
The ima group local edge up notification.
NOTIFICATION-TYPE    

hwDslImaGroupREDown 1.3.6.1.4.1.2011.5.25.157.2.2.3
The ima group remote edge down notification.
NOTIFICATION-TYPE    

hwDslImaGroupREUp 1.3.6.1.4.1.2011.5.25.157.2.2.4
The ima group remote edge up notification.
NOTIFICATION-TYPE    

hwDslImaLinkTraps 1.3.6.1.4.1.2011.5.25.157.2.3
OBJECT IDENTIFIER    

hwDslImaLinkLif 1.3.6.1.4.1.2011.5.25.157.2.3.1
The ima link lif notification.
NOTIFICATION-TYPE    

hwDslImaLinkLifResume 1.3.6.1.4.1.2011.5.25.157.2.3.2
The ima link lif resume notification.
NOTIFICATION-TYPE    

hwDslImaLinkLods 1.3.6.1.4.1.2011.5.25.157.2.3.3
The ima link lods notification.
NOTIFICATION-TYPE    

hwDslImaLinkLodsResume 1.3.6.1.4.1.2011.5.25.157.2.3.4
The ima link lods resume notification.
NOTIFICATION-TYPE    

hwDslImaLinkRfi 1.3.6.1.4.1.2011.5.25.157.2.3.5
The ima link rfi notification.
NOTIFICATION-TYPE    

hwDslImaLinkRfiResume 1.3.6.1.4.1.2011.5.25.157.2.3.6
The ima link rfi resume notification.
NOTIFICATION-TYPE    

hwDslImaLinkReTxUnusable 1.3.6.1.4.1.2011.5.25.157.2.3.7
The ima link remote tx unusable notification.
NOTIFICATION-TYPE    

hwDslImaLinkReTxUsable 1.3.6.1.4.1.2011.5.25.157.2.3.8
The ima link remote tx usable notification.
NOTIFICATION-TYPE    

hwDslImaLinkReRxUnusable 1.3.6.1.4.1.2011.5.25.157.2.3.9
The ima link remote rx unusable notification.
NOTIFICATION-TYPE    

hwDslImaLinkReRxUsable 1.3.6.1.4.1.2011.5.25.157.2.3.10
The ima link remote tx usable notification.
NOTIFICATION-TYPE    

hwDslLinkTraps 1.3.6.1.4.1.2011.5.25.157.2.4
OBJECT IDENTIFIER    

hwDslLinkFrameLost 1.3.6.1.4.1.2011.5.25.157.2.4.1
The dsl link frame lost notification.
NOTIFICATION-TYPE    

hwDslLinkFrameResume 1.3.6.1.4.1.2011.5.25.157.2.4.2
The dsl link frame resume notification.
NOTIFICATION-TYPE    

hwDslLinkSignalLost 1.3.6.1.4.1.2011.5.25.157.2.4.3
The dsl link signal lost notification.
NOTIFICATION-TYPE    

hwDslLinkSignalResume 1.3.6.1.4.1.2011.5.25.157.2.4.4
The dsl link signal resume notification.
NOTIFICATION-TYPE    

hwCesPwRemoteLosPktAlarm 1.3.6.1.4.1.2011.5.25.157.2.5
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwCesPwRemoteLosPktAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.6
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwCesPwOppositeRai 1.3.6.1.4.1.2011.5.25.157.2.7
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwCesPwOppositeRaiResume 1.3.6.1.4.1.2011.5.25.157.2.8
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwLosAlarm 1.3.6.1.4.1.2011.5.25.157.2.9
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwLosAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.10
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwLofAlarm 1.3.6.1.4.1.2011.5.25.157.2.11
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwLofAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.12
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwOofAlarm 1.3.6.1.4.1.2011.5.25.157.2.13
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwOofAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.14
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwB1TcaAlarm 1.3.6.1.4.1.2011.5.25.157.2.15
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwB1TcaAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.16
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwB2TcaAlarm 1.3.6.1.4.1.2011.5.25.157.2.17
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwB2TcaAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.18
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwJ0TimAlarm 1.3.6.1.4.1.2011.5.25.157.2.19
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwJ0TimAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.20
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwLrdiAlarm 1.3.6.1.4.1.2011.5.25.157.2.21
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwLrdiAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.22
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwSfbereAlarm 1.3.6.1.4.1.2011.5.25.157.2.23
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwSfbereAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.24
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwAuLopAlarm 1.3.6.1.4.1.2011.5.25.157.2.25
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwAuLopAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.26
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwLaisAlarm 1.3.6.1.4.1.2011.5.25.157.2.27
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwLaisAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.28
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwSdbereAlarm 1.3.6.1.4.1.2011.5.25.157.2.29
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwSdbereAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.30
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwPtimAlarm 1.3.6.1.4.1.2011.5.25.157.2.31
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwPtimAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.32
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwPuneqAlarm 1.3.6.1.4.1.2011.5.25.157.2.33
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwPuneqAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.34
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwPrdiAlarm 1.3.6.1.4.1.2011.5.25.157.2.35
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwPrdiAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.36
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwB3TcaAlarm 1.3.6.1.4.1.2011.5.25.157.2.37
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwB3TcaAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.38
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwPplmAlarm 1.3.6.1.4.1.2011.5.25.157.2.39
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwPplmAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.40
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwPaisAlarm 1.3.6.1.4.1.2011.5.25.157.2.41
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwPaisAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.42
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwAuAisAlarm 1.3.6.1.4.1.2011.5.25.157.2.43
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwAuAisAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.44
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwVlopAlarm 1.3.6.1.4.1.2011.5.25.157.2.45
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwVlopAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.46
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwLomAlarm 1.3.6.1.4.1.2011.5.25.157.2.47
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwLomAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.48
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwLpTimVc12Alarm 1.3.6.1.4.1.2011.5.25.157.2.49
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwLpTimVc12AlarmResume 1.3.6.1.4.1.2011.5.25.157.2.50
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwLpUneqVc12Alarm 1.3.6.1.4.1.2011.5.25.157.2.51
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwLpUneqVc12AlarmResume 1.3.6.1.4.1.2011.5.25.157.2.52
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwVrdiAlarm 1.3.6.1.4.1.2011.5.25.157.2.53
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwVrdiAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.54
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwBip2TcaAlarm 1.3.6.1.4.1.2011.5.25.157.2.57
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwBip2TcaAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.58
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwLpSlmVc12Alarm 1.3.6.1.4.1.2011.5.25.157.2.59
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwLpSlmVc12AlarmResume 1.3.6.1.4.1.2011.5.25.157.2.60
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwTuAisVc12Alarm 1.3.6.1.4.1.2011.5.25.157.2.61
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwTuAisVc12AlarmResume 1.3.6.1.4.1.2011.5.25.157.2.62
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwE1EsTcaAlarm 1.3.6.1.4.1.2011.5.25.157.2.63
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwE1EsTcaAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.64
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwE1LmfaAlarm 1.3.6.1.4.1.2011.5.25.157.2.67
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwE1LmfaAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.68
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwE1UpE1AisAlarm 1.3.6.1.4.1.2011.5.25.157.2.69
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwE1UpE1AisAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.70
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwE1AlmE1RaiAlarm 1.3.6.1.4.1.2011.5.25.157.2.71
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwE1AlmE1RaiAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.72
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwCesPwOppositeAcFault 1.3.6.1.4.1.2011.5.25.157.2.73
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwCesPwOppositeAcFaultResume 1.3.6.1.4.1.2011.5.25.157.2.74
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwCesLosPktExcAlarm 1.3.6.1.4.1.2011.5.25.157.2.75
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwCesLosPktExcAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.76
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwCesMisorderPktExcAlarm 1.3.6.1.4.1.2011.5.25.157.2.77
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwCesMisorderPktExcAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.78
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwCesStrayPktExcAlarm 1.3.6.1.4.1.2011.5.25.157.2.79
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwCesStrayPktExcAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.80
Indicates the alarm is cleared.
NOTIFICATION-TYPE    

hwCesMalPktExcAlarm 1.3.6.1.4.1.2011.5.25.157.2.81
Indicates the alarm is detected.
NOTIFICATION-TYPE    

hwCesMalPktExcAlarmResume 1.3.6.1.4.1.2011.5.25.157.2.82
Indicates the alarm is cleared.
NOTIFICATION-TYPE