HUAWEI-MPLSOAM-PS-MIB

File: HUAWEI-MPLSOAM-PS-MIB.mib (20513 bytes)

Imported modules

HUAWEI-MPLSOAM-MIB	IF-MIB	SNMPv2-CONF
SNMPv2-SMI	SNMPv2-TC

Imported symbols

hwMplsOam	InterfaceIndex	OBJECT-GROUP
MODULE-COMPLIANCE	NOTIFICATION-GROUP	IpAddress
Integer32	Unsigned32	OBJECT-TYPE
NOTIFICATION-TYPE	RowStatus	TruthValue

Defined Types

HwMplsPsEntry
SEQUENCE
	hwMplsPsIndex	Unsigned32
	hwMplsPsType	Integer32
	hwMplsPsWorkTunnName	OCTET STRING
	hwMplsPsWorkTunnId	Integer32
	hwMplsPsProtectTunnName	OCTET STRING
	hwMplsPsProtectTunnId	Integer32
	hwMplsPsRevertiveMode	Integer32
	hwMplsPsWTR	Integer32
	hwMplsPsHoldOff	Integer32
	hwMplsPsSwitchCondition	Integer32
	hwMplsPsWorkTunnelState	Integer32
	hwMplsPsProtTunnelState	Integer32
	hwMplsPsSwitchResult	Integer32
	hwMplsPsCfgType	Integer32
	hwMplsPsCfgProtectTunnId	Integer32
	hwMplsPsCfgRevertiveMode	Integer32
	hwMplsPsCfgWTR	Integer32
	hwMplsPsCfgHoldOff	Integer32
	hwMplsPsRowStatus	RowStatus

HwMplsVCPsEntry
SEQUENCE
	hwMplsVCPsIfIndex	InterfaceIndex
	hwMplsVCPsTNLBinding	TruthValue
	hwMplsTeReverseLspName	OCTET STRING
	hwMplsVcPsRowStatus	RowStatus
	hwMplsTeReverseLspLsrId	IpAddress
	hwMplsTeReverseLspTunnId	Integer32

Defined Values

hwMplsOamPs		1.1.2011.5.12.7.1
OBJECT IDENTIFIER

hwMplsPsObjects		1.1.2011.5.12.7.1.3
OBJECT IDENTIFIER

hwMplsPsTable		1.1.2011.5.12.7.1.3.1
This table specifies per-protection-group MPLS PS capability and associated information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsPsEntry

hwMplsPsEntry		1.1.2011.5.12.7.1.3.1.1
An entry in this table is created by an LSR for every protection group capable of supporting mpls ps.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsPsEntry

hwMplsPsIndex		1.1.2011.5.12.7.1.3.1.1.1
This is a unique index for an entry in the mplspsEntry.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsPsType		1.1.2011.5.12.7.1.3.1.1.2
The type of protection switch,can be 1:1,1+1,shared mesh, packet 1+1,the default choice is 1:1. In the 1+1 architecture type, a protection LSP is dedicated to each working LSP with the working LSP bridged onto the protection LSP at the source of the protection domain. The traffic on working and protection LSPs is transmitted simultaneously to the sink of the protection domain, where a selection between the working and protection LSP is made, based on some predetermined criteria, such as defect indication. In the 1:1 architecture type, a protection LSP is dedicated to each working LSP. The working traffic is transmitted either by working or protection LSP. In the shared mesh architecture type, possible sharing of protection capacity between disjoint link, node in the network is achieved while guaranteeing recovery from a single failure. In the packet 1+1 architecture type, the traffic is transmitted simultaneously onto two possibly disjoint routed LSPs to the sink of the protection domain. Each pair of duplicate transmitted packets is assigned the same identifier (sequence number) but distinct from the other pairs of duplicate packets. At the sink of the protection domain packet level selection mechanism is employed to select one of the two possibly received copies of each packet. 1: 1:1 protection switching,; 2: 1+1 protection switching; 3: shared mesh protection swiching; 4: packet 1+1 protection switching.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4

hwMplsPsWorkTunnName		1.1.2011.5.12.7.1.3.1.1.3
The name of work-tunnel.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

hwMplsPsWorkTunnId		1.1.2011.5.12.7.1.3.1.1.4
Work-tunnel id(session-tunnel-id).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

hwMplsPsProtectTunnName		1.1.2011.5.12.7.1.3.1.1.5
The name of protect-tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hwMplsPsProtectTunnId		1.1.2011.5.12.7.1.3.1.1.6
Protect-tunnel id(session-tunnel-id).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

hwMplsPsRevertiveMode		1.1.2011.5.12.7.1.3.1.1.7
Revertive mode is a protection switching mode where revertive action (switch back to the working LSP) is taken after the working LSP is repaired.And switching does not occur in a non-revertive mode. 1: revertive; 2: non-revertive;
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

hwMplsPsWTR		1.1.2011.5.12.7.1.3.1.1.8
Wait to Restore timer is only applicable for the revertive mode and applies to a working LSP,It prevents reversion back to select the working LSP until the Wait to Restore timer has expired.The default value is 12 minutes.step is 30s.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..60

hwMplsPsHoldOff		1.1.2011.5.12.7.1.3.1.1.9
The time between declaration of signal degrade or signal fail, and the initialization of the protection switching algorithm. step is 100ms.maximum is 10s.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..100

hwMplsPsSwitchCondition		1.1.2011.5.12.7.1.3.1.1.10
The current switch condition of the protection group. 1: clear,This command clears all of the externally initiated switch commands listed below; 2: lockout of protection,Fix the selector position on the working LSP,Prevents the selector from switching to the protection LSP when it is selecting the working LSP. Switches the selector from the protection to the working LSP when it is selecting the protection LSP; 3: forced protection,Switches the selector from the working LSP to the protection LSP (unless a higher priority switch request (i.e., LoP) is in effect); 4: signal fail,for 1:1,Signal Fail (SF) is declared when the source of the protection domain enters the Defect State by receiving a BDI packet (from the return LSP or out of band). 5: manual switch for working-lsp,Switches the selector from the working LSP to the protection LSP (unless an equal or higher priority switch request (i.e., LoP, FS, SF or MS) is in effect); 6: manual switch for protection-lsp,Switches the selector from the protection LSP to the working LSP (unless an equal or higher priority switch request (i.e., LoP, FS, SF or MS) is in effect). 7: WTR-timer; 8: HoldOff-timer; 9: Others; The pripority of the commands are: clear > lockout of protection > force switch > manual switch for working lsp = manual switch for protection lsp
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..9

hwMplsPsWorkTunnelState		1.1.2011.5.12.7.1.3.1.1.11
The state of working tunnel state in one protection group, whether it is in detection, 1: it is outof defect 2: it enters defect
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

hwMplsPsProtTunnelState		1.1.2011.5.12.7.1.3.1.1.12
The state of protection tunnel state in one protection group, whether it is in detection, 1: it is outof defect 2: it enters defect
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

hwMplsPsSwitchResult		1.1.2011.5.12.7.1.3.1.1.13
Which tunnel is used to transfer the data stream. 1: working-tunnel 2: protection-tunnel
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

hwMplsPsCfgType		1.1.2011.5.12.7.1.3.1.1.14
The type of protection switch which is configured. 1: 1:1 2: 1+1 3: shared mesh 4: packet 1:1
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

hwMplsPsCfgProtectTunnId		1.1.2011.5.12.7.1.3.1.1.15
Protect-tunnel id(session-tunnel-id).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

hwMplsPsCfgRevertiveMode		1.1.2011.5.12.7.1.3.1.1.16
Revertive mode is a protection switching mode where revertive action (switch back to the working LSP) is taken after the working LSP is repaired.And switching does not occur in a non-revertive mode. 1: revertive; 2: non-revertive;
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..2

hwMplsPsCfgWTR		1.1.2011.5.12.7.1.3.1.1.17
Wait to Restore timer is only applicable for the revertive mode and applies to a working LSP,It prevents reversion back to select the working LSP until the Wait to Restore timer has expired.The default value is 12 minutes.step is 30s.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..60

hwMplsPsCfgHoldOff		1.1.2011.5.12.7.1.3.1.1.18
The time between declaration of signal degrade or signal fail, and the initialization of the protection switching algorithm. step is 100ms.maximum is 10s.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..100

hwMplsPsRowStatus		1.1.2011.5.12.7.1.3.1.1.19
This variable is used to create, modify, and delete a row in this table. 1: active 2: not in service 3: not ready 4: create and go 5: create and wait 6: destroy
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

hwTunnPsTrapOpen		1.1.2011.5.12.7.1.3.2
1:enable; 2:disable;
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..2

hwMplsVCPsTable		1.1.2011.5.12.7.1.3.3
Description.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsVCPsEntry

hwMplsVCPsEntry		1.1.2011.5.12.7.1.3.3.1
this table for these commands 1.mpls te protection tunnel XXX 2. mpls te reverse-lsp { lsp-name XXXX \| lsr-id X.X.X.X tunnel-id x } 3. mpls te reserved-for-binding
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsVCPsEntry

hwMplsVCPsIfIndex		1.1.2011.5.12.7.1.3.3.1.1
Description.the index of working tunnel interface of Protection group
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

hwMplsVCPsTNLBinding		1.1.2011.5.12.7.1.3.3.1.2
Description.it is used by command ' mpls te reserved-for-binding '
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

hwMplsTeReverseLspName		1.1.2011.5.12.7.1.3.3.1.3
Description.it is used for command ' mpls te reverse-lsp lspname'
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

hwMplsVcPsRowStatus		1.1.2011.5.12.7.1.3.3.1.4
Description. 1: active; 2: notInservice; 3: notReady; 4: CreateAndGo; 5: CreateAndWait; 6: destroy;
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hwMplsTeReverseLspLsrId		1.1.2011.5.12.7.1.3.3.1.5
Description.it is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX'
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

hwMplsTeReverseLspTunnId		1.1.2011.5.12.7.1.3.3.1.6
Description.it is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX'
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

hwMplsPsNotifications		1.1.2011.5.12.7.1.4
OBJECT IDENTIFIER

hwMplsPsSwitchPtoW		1.1.2011.5.12.7.1.4.1
This notification is generated when switching from protection-lsp to working-lsp occured.
Status: current	Access: read-create
NOTIFICATION-TYPE

hwMplsPsSwitchWtoP		1.1.2011.5.12.7.1.4.2
This notification is generated when switching from woking-lsp to protection-lsp occured.
Status: current	Access: read-create
NOTIFICATION-TYPE

hwMplsOamPsConformance		1.1.2011.5.12.7.1.100
OBJECT IDENTIFIER

hwMplsOamPsCompliances		1.1.2011.5.12.7.1.100.1
OBJECT IDENTIFIER

hwMplsOamPsGroupCompliance		1.1.2011.5.12.7.1.100.1.1
The compliance statement for mpls oam ps.
Status: current	Access: read-create
MODULE-COMPLIANCE

hwMplsOamPsGroups		1.1.2011.5.12.7.1.100.2
OBJECT IDENTIFIER

hwMplsPsGroup		1.1.2011.5.12.7.1.100.2.1
The compliance statement for mpls oam ps management.
Status: current	Access: read-create
OBJECT-GROUP

hwMplsVcPsGroup		1.1.2011.5.12.7.1.100.2.2
The compliance statement for mpls oam ps reverse lsp.
Status: current	Access: read-create
OBJECT-GROUP

hwMplsPsNotificationGroup		1.1.2011.5.12.7.1.100.2.3
Description.
Status: current	Access: read-create
NOTIFICATION-GROUP