HUAWEI-MPLS-EXTEND-MIB

File: HUAWEI-MPLS-EXTEND-MIB.mib (157771 bytes)

Imported modules

HUAWEI-MIB	IF-MIB	MPLS-LSR-STD-MIB
MPLS-TC-STD-MIB	SNMP-FRAMEWORK-MIB	SNMPv2-CONF
SNMPv2-SMI	MPLS-TE-STD-MIB	INET-ADDRESS-MIB

Imported symbols

hwDatacomm	ifIndex	ifName
MplsIndexType	MplsTunnelIndex	MplsTunnelInstanceIndex
MplsExtendedTunnelId	MplsLsrIdentifier	SnmpAdminString
OBJECT-GROUP	NOTIFICATION-GROUP	MODULE-COMPLIANCE
Integer32	Unsigned32	Counter32
Counter64	OBJECT-TYPE	MODULE-IDENTITY
NOTIFICATION-TYPE	mplsTunnelAdminStatus	mplsTunnelOperStatus
InetAddressType	InetAddress

Defined Types

HwMplsTunnelEntry
SEQUENCE
	hwMplsTunnelIndex	MplsTunnelIndex
	hwMplsTunnelInstance	MplsTunnelInstanceIndex
	hwMplsTunnelIngressLSRId	MplsExtendedTunnelId
	hwMplsTunnelEgressLSRId	MplsExtendedTunnelId
	hwMplsTunnelClassType	INTEGER
	hwMplsTunnelBandwidth	Integer32
	hwMplsTunnelAdminStatus	INTEGER
	hwMplsTunnelOperStatus	INTEGER
	hwMplsTunnelSessionAttr	BITS
	hwMplsTunnelFrrSetupPrio	Unsigned32
	hwMplsTunnelFrrHoldingPrio	Unsigned32
	hwMplsTunnelFrrBandwidth	Unsigned32
	hwMplsTunnelFrrSwitchover	Counter32
	hwMplsTunnelFrrBypassTableIndex	Unsigned32
	hwMplsTunnelFrrARHopTableIndex	Unsigned32
	hwMplsTunnelName	SnmpAdminString
	hwMplsTunnelIfIndex	Unsigned32
	hwMplsTunnelPreBandwidth	Unsigned32
	hwMplsTunnelNextBandwidth	Unsigned32
	hwMplsTunnelCt0Bandwidth	Unsigned32
	hwMplsTunnelCt1Bandwidth	Unsigned32
	hwMplsTunnelCt2Bandwidth	Unsigned32
	hwMplsTunnelCt3Bandwidth	Unsigned32
	hwMplsTunnelCt4Bandwidth	Unsigned32
	hwMplsTunnelCt5Bandwidth	Unsigned32
	hwMplsTunnelCt6Bandwidth	Unsigned32
	hwMplsTunnelCt7Bandwidth	Unsigned32
	hwMplsTunnelLspType	INTEGER
	hwMplsTunnelInterfaceName	SnmpAdminString
	hwMplsTunnelSignalProto	INTEGER
	hwMplsTunnelType	INTEGER

HwTunnelFrrBypassEntry
SEQUENCE
	hwTunnelFrrBypassListIndex	Unsigned32
	hwTunnelFrrBypassIndex	Unsigned32
	hwTunnelFrrBypassProtIfIndex	Unsigned32

HwTunnelFrrARHopEntry
SEQUENCE
	hwTunnelFrrARHopListIndex	Unsigned32
	hwTunnelFrrARHopIndex	Unsigned32
	hwTunnelFrrARHopProtDesired	BITS
	hwTunnelFrrARHopProtActual	BITS

HwTunnelFrrRouteDBEntry
SEQUENCE
	hwTunnelFrrRouteDBTunnelIndex	Unsigned32
	hwTunnelFrrRouteDBTunnelInstance	Unsigned32
	hwTunnelFrrRouteDBTunnelIngressLSRId	Unsigned32
	hwTunnelFrrRouteDBTunnelEngressLSRId	Unsigned32
	hwTunnelFrrRouteDBBypassIfIndex	Unsigned32
	hwTunnelFrrRouteDBInnerLabel	Unsigned32

HwStaticLspEntry
SEQUENCE
	hwStaticLspIndex	MplsIndexType
	hwStaticLspInSegmentIndex	MplsIndexType
	hwStaticLspOutSegmentIndex	MplsIndexType
	hwStaticLspOwner	INTEGER
	hwStaticLspName	SnmpAdminString
	hwStaticLspStatus	INTEGER
	hwStaticLspClassType	INTEGER
	hwStaticLspBandwidth	Unsigned32

HwMplsTeClassEntry
SEQUENCE
	hwMplsTeClassId	Unsigned32
	hwMplsTeClassClassType	INTEGER
	hwMplsTeClassPriority	Unsigned32
	hwMplsTeClassDescription	OCTET STRING

HwMplsIfBcEntry
SEQUENCE
	hwMplsIfMaxResvBandwidth	Unsigned32
	hwMplsIfBc0Bandwidth	Unsigned32
	hwMplsIfBc1Bandwidth	Unsigned32
	hwMplsIfBc2Bandwidth	Unsigned32
	hwMplsIfBc3Bandwidth	Unsigned32
	hwMplsIfBc4Bandwidth	Unsigned32
	hwMplsIfBc5Bandwidth	Unsigned32
	hwMplsIfBc6Bandwidth	Unsigned32
	hwMplsIfBc7Bandwidth	Unsigned32

HwStaticLspTnlEntry
SEQUENCE
	hwStaticLspTnlName	SnmpAdminString
	hwStaticLspTnlToken	Unsigned32

HwMplsTeVpnQosEntry
SEQUENCE
	hwMplsTnlID	Unsigned32
	hwMplsTeVpnMaxBandwidth	Unsigned32
	hwMplsTeVpnAllocatedBandwidth	Unsigned32

HwMplsLspStatisticsEntry
SEQUENCE
	hwMplsLspStatisticsLspType	INTEGER
	hwMplsLspStatisticsIngressLspCount	Unsigned32
	hwMplsLspStatisticsTransitLspCount	Unsigned32
	hwMplsLspStatisticsEgressLspCount	Unsigned32
	hwMplsLspStatisticsTotalLspCount	Unsigned32

HwMplsTrafficStatisticsStaticLspEntry
SEQUENCE
	hwMplsTrafficStatisticsStaticLspName	SnmpAdminString
	hwMplsTrafficStatisticsStaticLspForwardInBytes	Counter64
	hwMplsTrafficStatisticsStaticLspForwardInPackets	Counter64
	hwMplsTrafficStatisticsStaticLspForwardOutBytes	Counter64
	hwMplsTrafficStatisticsStaticLspForwardOutPackets	Counter64
	hwMplsTrafficStatisticsStaticLspBackwardInBytes	Counter64
	hwMplsTrafficStatisticsStaticLspBackwardInPackets	Counter64
	hwMplsTrafficStatisticsStaticLspBackwardOutBytes	Counter64
	hwMplsTrafficStatisticsStaticLspBackwardOutPackets	Counter64

HwMplsRingEntry
SEQUENCE
	hwMplsRingID	Unsigned32
	hwMplsRingNodeID	Unsigned32
	hwMplsRingName	OCTET STRING
	hwMplsRingDirection	OCTET STRING
	hwMplsRingSwitchReason	OCTET STRING

Defined Values

hwMplsExtendMib		1.3.6.1.4.1.2011.5.25.121
This MIB is used for defining the HUAWEI private extended Multiprotocol Label Switching (MPLS) MIB object. All MIB objects are used to describe private managed objects and trap definitions for MPLS.
MODULE-IDENTITY

hwMplsExtendMibTunnel		1.3.6.1.4.1.2011.5.25.121.1
OBJECT IDENTIFIER

hwMplsTunnelTable		1.3.6.1.4.1.2011.5.25.121.1.1
A tunnel needs to be uniquely identified across an MPLS network. Indexes hwMplsTunnelIndex and hwMplsTunnelInstance uniquely identify a tunnel on the LSR originating the tunnel. hwMplsTunnelIngressLSRId uniquely identifies a tunnel across an MPLS network. The last index hwMplsTunnelEgressLSRId is useful in identifying all instances of a tunnel that are terminated on the same egress LSR. The indexes of this table are hwMplsTunnelIndex, hwMplsTunnelInstance, hwMplsTunnelIngressLSRId and hwMplsTunnelEgressLSRId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsTunnelEntry

hwMplsTunnelEntry		1.3.6.1.4.1.2011.5.25.121.1.1.1
A tunnel needs to be uniquely identified across an MPLS network. Indexes hwMplsTunnelIndex and hwMplsTunnelInstance uniquely identify a tunnel on the LSR originating the tunnel. hwMplsTunnelIngressLSRId uniquely identifies a tunnel across an MPLS network. The last index hwMplsTunnelEgressLSRId is useful in identifying all instances of a tunnel that are terminated on the same egress LSR. The indexes of this entry are hwMplsTunnelIndex, hwMplsTunnelInstance, hwMplsTunnelIngressLSRId and hwMplsTunnelEgressLSRId.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsTunnelEntry

hwMplsTunnelIndex		1.3.6.1.4.1.2011.5.25.121.1.1.1.1
Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. When the MPLS signalling protocol is rsvp(2), this value equals to the value signaled in the Tunnel ID of the SESSION object. When the MPLS signalling protocol is crldp(3), this value equals to the value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsTunnelIndex

hwMplsTunnelInstance		1.3.6.1.4.1.2011.5.25.121.1.1.1.2
Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is used to identify multiple instances of tunnels for backup and parallel tunnels. When the MPLS signaling protocol is rsvp(2), this value equals to the LSP ID of the Sender Template object. When the signaling protocol is crldp(3) there is no equivalent signaling object. Reference to MPLS-TE-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsTunnelInstanceIndex

hwMplsTunnelIngressLSRId		1.3.6.1.4.1.2011.5.25.121.1.1.1.3
Indicates the ingress LSR ID of this tunnel. When the MPLS signalling protocol is rsvp(2), this value equals to the Tunnel Sender Address in the Sender Template object and may equal to the Extended Tunnel ID in the SESSION object. When the MPLS signalling protocol is crldp(3), this value equals to the Ingress LSR Router ID in the LSPID TLV object. Reference to MPLS-TE-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsExtendedTunnelId

hwMplsTunnelEgressLSRId		1.3.6.1.4.1.2011.5.25.121.1.1.1.4
Indicates the egress LSR ID of this tunnel. Reference to MPLS-TE-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsExtendedTunnelId

hwMplsTunnelClassType		1.3.6.1.4.1.2011.5.25.121.1.1.1.5
Indicates the bandwidth type used by this tunnel. Options: 1. bc0(1) -indicates the bandwidth type is bc0. 2. bc1(2) -indicates the bandwidth type is bc1. 3. invalidValue(3) -indicates the invalid value.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bc0(1), bc1(2), invalidValue(3)

hwMplsTunnelBandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.6
Indicates the bandwidth used by this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hwMplsTunnelAdminStatus		1.3.6.1.4.1.2011.5.25.121.1.1.1.7
Indicates the management status of this tunnel.Reference to MPLS-TE-STD-MIB. Options: 1. up(1) -indicates the management status of this tunnel is up. 2. down(2) -indicates the management status of this tunnel is down. 3. testing(3) -indicates the tunnel is used in some test mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

hwMplsTunnelOperStatus		1.3.6.1.4.1.2011.5.25.121.1.1.1.8
Indicates the actual operational status of this tunnel, which is but not limited to the status of this tunnel of a certain period.Reference to MPLS-TE-STD-MIB. Options: 1. up(1) -indicates that the operational status of this tunnel is up. 2. down(2) -indicates that the operational status of this tunnel is down. 3. testing(3) -indicates that the tunnel is used in some test mode. 4. unknown(4) -indicates the invalid value. 5. dormant(5) -indicates that the status cannot be determined. 6. notPresent(6) -indicates that some component is missing 7. lowerLayerDown(7) -indicates the Down state due to the state of lower layer interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), unknown(4), dormant(5), notPresent(6), lowerLayerDown(7)

hwMplsTunnelSessionAttr		1.3.6.1.4.1.2011.5.25.121.1.1.1.9
Indicates protection types desired by the primary tunnel, such as node protection, link protection or bandwidth protection. Options: 1. localProtectionDesired(0) -indicates link protection. 2. nodeProtectionDesired(1) -indicates node protection. 3. bandwidthProtectionDesired(2) -indicates bandwidth protection.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	localProtectionDesired(0), nodeProtectionDesired(1), bandwidthProtectionDesired(2)

hwMplsTunnelFrrSetupPrio		1.3.6.1.4.1.2011.5.25.121.1.1.1.10
Indicates the setup PRI of auto-bypass tunnel. Range: 0-7 Default: 7
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelFrrHoldingPrio		1.3.6.1.4.1.2011.5.25.121.1.1.1.11
Indicates the holding PRI of auto-bypass tunnel. Range: 0-7 Default: 7
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelFrrBandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.12
Indicates the protecting bandwidth of auto-bypass tunnel. Its value is defined by the configuration on the primary tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelFrrSwitchover		1.3.6.1.4.1.2011.5.25.121.1.1.1.13
Indicates FRR switching times
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwMplsTunnelFrrBypassTableIndex		1.3.6.1.4.1.2011.5.25.121.1.1.1.14
Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel. The bypass table shows interfaces protected by specified bypass tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelFrrARHopTableIndex		1.3.6.1.4.1.2011.5.25.121.1.1.1.15
Indicates the table index of the protection type adopted by each hop of the primary tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelName		1.3.6.1.4.1.2011.5.25.121.1.1.1.16
Indicates the tunnel name. The name can refer to the tunnel on the console port of the LSR. If mplsTunnelIsIf is set to True, the IfName of the interface corresponding to this tunnel should have a value equal to hwMplsTunnelName. Reference to the description of IfName in RFC 2863.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hwMplsTunnelIfIndex		1.3.6.1.4.1.2011.5.25.121.1.1.1.17
Indicates the interface index of the tunnel. It uniquely identifies the tunnel name.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelPreBandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.18
Indicates the original bandwidth of the tunnel when the tunnel is in the Modify state. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelNextBandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.19
Indicates the bandwidth of the tunnel that is to be changed when the tunnel is in the Modify state. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelCt0Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.20
The bandwidth of Class-Type 0 (CT0) in this tunnel, in kbit/s. If all CT bandwidths are 0s, it means that this tunnel's Class-Type is CT0, and bandwidth is 0 kbit/s. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelCt1Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.21
The bandwidth of Class-Type 1 (CT1) in this tunnel, in kbit/s. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelCt2Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.22
The bandwidth of Class-Type 2 (CT2) in this tunnel, in kbit/s. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelCt3Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.23
The bandwidth of Class-Type 3 (CT3) in this tunnel, in kbit/s. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelCt4Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.24
The bandwidth of Class-Type 4 (CT4) in this tunnel, in kbit/s. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelCt5Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.25
The bandwidth of Class-Type 5 (CT5) in this tunnel, in kbit/s. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelCt6Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.26
The bandwidth of Class-Type 6 (CT6) in this tunnel, in kbit/s. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelCt7Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.1.1.27
The bandwidth of Class-Type 7 (CT7) in this tunnel, in kbit/s. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTunnelLspType		1.3.6.1.4.1.2011.5.25.121.1.1.1.28
This object is meaningful only at the ingress of the tunnel. It indicates LSP types. Options: 0. invalid(0) -indicates that the LSP type is invalid, the possible cause is that the LSP is not created at an ingress. 1. primary(1) -indicates the primary LSP 2. primaryModifing(2) -indicates the LSP that will replace the primary LSP 3. hotStandby(3) -indicates the hot-standby LSP 4. hotStandbyModifing(4) -indicates the LSP that will replace the hot-standby LSP 5. ordinary(5) -indicates the ordinary LSP 6. ordinaryModifing(6) -indicates the LSP that will replace the ordinary LSP 7. bestEffort(7) -indicates the Best-Effort LSP 8. bestEffortModifing(8) -indicates the LSP that will replace the Best-Effort LSP Modifying LSPs are created when users modify the make-before-break attribute of the corresponding LSP types. After being created, modifying LSPs replace the corresponding LSPs to transmit traffic.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	invalid(0), primary(1), primaryModifing(2), hotStandby(3), hotStandbyModifing(4), ordinary(5), ordinaryModifing(6), bestEffort(7), bestEffortModifing(8)

hwMplsTunnelInterfaceName		1.3.6.1.4.1.2011.5.25.121.1.1.1.29
Indicates the tunnel interface name. The object is only valid at the ingress.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hwMplsTunnelSignalProto		1.3.6.1.4.1.2011.5.25.121.1.1.1.30
Indicates the signal protocol of this tunnel
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rsvpTE(1), static(2), staticCR(3)

hwMplsTunnelType		1.3.6.1.4.1.2011.5.25.121.1.1.1.31
This object is meaningful only at the ingress of the tunnel. It indicates tunnel types. Options: 1. invalid(1) -indicates that the tunnel type is invalid, the possible cause is that it is not ingress node of this tunnel 2. primaryTunnel(2) -indicates that this is a primary tunnel 3. bypassTunnel(3) -indicates that this is a bypass tunnel
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	invalid(1), primaryTunnel(2), bypassTunnel(3)

hwTunnelFrrBypassTable		1.3.6.1.4.1.2011.5.25.121.1.2
Indicates the bypass tunnel. The indexes of this table are hwTunnelFrrBypassListIndex and hwTunnelFrrBypassIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwTunnelFrrBypassEntry

hwTunnelFrrBypassEntry		1.3.6.1.4.1.2011.5.25.121.1.2.1
Indicates the bypass tunnel.The indexes of this entry are hwTunnelFrrBypassListIndex and hwTunnelFrrBypassIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwTunnelFrrBypassEntry

hwTunnelFrrBypassListIndex		1.3.6.1.4.1.2011.5.25.121.1.2.1.1
Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwTunnelFrrBypassIndex		1.3.6.1.4.1.2011.5.25.121.1.2.1.2
Indicates the index of the bypass tunnel interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwTunnelFrrBypassProtIfIndex		1.3.6.1.4.1.2011.5.25.121.1.2.1.3
Indicates the index of the interface protected by the bypass tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwTunnelFrrARHopTable		1.3.6.1.4.1.2011.5.25.121.1.3
Indicates the FrrARHopTable, which will show every hop's frr protect information of the tunnel. The indexes of this table are hwTunnelFrrARHopListIndex and hwTunnelFrrARHopIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwTunnelFrrARHopEntry

hwTunnelFrrARHopEntry		1.3.6.1.4.1.2011.5.25.121.1.3.1
Indicates the FrrARHopTable, which will show every hop's frr protect information of the tunnel. The indexes of this entry are hwTunnelFrrARHopListIndex and hwTunnelFrrARHopIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwTunnelFrrARHopEntry

hwTunnelFrrARHopListIndex		1.3.6.1.4.1.2011.5.25.121.1.3.1.1
Indicates the table index of each hop along the primary tunnel.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwTunnelFrrARHopIndex		1.3.6.1.4.1.2011.5.25.121.1.3.1.2
Indicates the index of each hop along the primary tunnel.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwTunnelFrrARHopProtDesired		1.3.6.1.4.1.2011.5.25.121.1.3.1.3
Indicates the FRR protection types desired by the primary tunnel interface, including: 0: link protection, 1: node protection, 2: bandwidth protection
Status: current	Access: read-only
OBJECT-TYPE
	BITS	localProtection(0), nodeProtection(1), bandwidthProtection(2)

hwTunnelFrrARHopProtActual		1.3.6.1.4.1.2011.5.25.121.1.3.1.4
Indicates the actual FRR protection types of the primary tunnel interface, including: 0: link protection, 1: node protection, 2: bandwidth protection, 3: primary tunnel protection in use
Status: current	Access: read-only
OBJECT-TYPE
	BITS	localProtection(0), nodeProtection(1), bandwidthProtection(2), protectionInuse(3)

hwTunnelFrrRouteDBTable		1.3.6.1.4.1.2011.5.25.121.1.4
Indicates the primary tunnel is protected by which bypass tunnel. The indexes of this table are hwTunnelFrrRouteDBTunnelIndex, hwTunnelFrrRouteDBTunnelInstance, hwTunnelFrrRouteDBTunnelIngressLSRId and hwTunnelFrrRouteDBTunnelEngressLSRId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwTunnelFrrRouteDBEntry

hwTunnelFrrRouteDBEntry		1.3.6.1.4.1.2011.5.25.121.1.4.1
Indicates the primary tunnel is protected by which bypass tunnel. The indexes of this entry are hwTunnelFrrRouteDBTunnelIndex, hwTunnelFrrRouteDBTunnelInstance, hwTunnelFrrRouteDBTunnelIngressLSRId and hwTunnelFrrRouteDBTunnelEngressLSRId.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwTunnelFrrRouteDBEntry

hwTunnelFrrRouteDBTunnelIndex		1.3.6.1.4.1.2011.5.25.121.1.4.1.1
Identifies the index of the primary. Manager obtains new index values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signaling protocol is rsvp(2), this value equals to the value signaled in the Tunnel ID of the SESSION object. When the MPLS signaling protocol is crldp(3), this value equals to the value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwTunnelFrrRouteDBTunnelInstance		1.3.6.1.4.1.2011.5.25.121.1.4.1.2
Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is the object identifies multiple instances of tunnels for the purposes of backup and parallel tunnels. When the MPLS signaling protocol is rsvp(2), this value equals to the LSP ID of the Sender Template object. When the signaling protocol is crldp(3), there is no equivalent signaling object. Reference to MPLS-TE-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwTunnelFrrRouteDBTunnelIngressLSRId		1.3.6.1.4.1.2011.5.25.121.1.4.1.3
Identifies the ingress LSR ID of the primary tunnel. When the MPLS signalling protocol is rsvp(2),LSR ID equals to the Tunnel Sender Address in the Sender Template object or the Extended Tunnel Id in the SESSION object. When the MPLS signalling protocol is crldp(3), LSR ID equals to the Ingress LSR Router ID in the LSPID TLV object.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwTunnelFrrRouteDBTunnelEngressLSRId		1.3.6.1.4.1.2011.5.25.121.1.4.1.4
Identifies the egress LSR ID of the primary tunnel. Reference to MPLS-TE-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwTunnelFrrRouteDBBypassIfIndex		1.3.6.1.4.1.2011.5.25.121.1.4.1.5
Indicates the interface index of the bypass tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwTunnelFrrRouteDBInnerLabel		1.3.6.1.4.1.2011.5.25.121.1.4.1.6
Indicates the inner label of the primary tunnel and bypass tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwStaticLspTable		1.3.6.1.4.1.2011.5.25.121.1.5
A static LSP is created by a network administrator by using static MPLS. Note that only point-to-point static LSP segments are supported. Each static MPLS LSP can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR. The indexes of this table are hwStaticLspIndex, hwStaticLspInSegmentIndex, and hwStaticLspOutSegmentIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwStaticLspEntry

hwStaticLspEntry		1.3.6.1.4.1.2011.5.25.121.1.5.1
A static LSP is created by a network administrator by using static MPLS. Note that only point-to-point static LSP segments are supported. Each static MPLS LSP can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR. The indexes of this entry are hwStaticLspIndex, hwStaticLspInSegmentIndex, and hwStaticLspOutSegmentIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwStaticLspEntry

hwStaticLspIndex		1.3.6.1.4.1.2011.5.25.121.1.5.1.1
Indicates the index of the static LSP. If the string is 0x00, it means that the index is invalid.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsIndexType

hwStaticLspInSegmentIndex		1.3.6.1.4.1.2011.5.25.121.1.5.1.2
Indicates the incoming label index of the static LSP/CR-LSP. If the string is 0x00, it means that the index is invalid. In this case, no corresponding mplsInSegmentEntry exists. Reference to MPLS-LSR-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsIndexType

hwStaticLspOutSegmentIndex		1.3.6.1.4.1.2011.5.25.121.1.5.1.3
Indicates the outgoing index of the static LSP/CR-LSP. If the entry is used to identify the incoming node or intermediate node of the LSP, this object cannot be set to the string 0x00. Because corresponding mplsOutSegmentEntry exists. If the entry is used to identify the outgoing node of the LSP, this object must be set to the string 0x00. Because no corresponding mplsOutSegmentEntry exists. Reference to MPLS-LSR-STD-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsIndexType

hwStaticLspOwner		1.3.6.1.4.1.2011.5.25.121.1.5.1.4
Denotes the entity that creates and manages the static LSP. See MPLS-LSR-STD-MIB. Options: 1. static(1) -indicates the static LSP. 2. crstatic(2) -indicates the static CR-LSP. 3. other(3) -indicates the LSP of another type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), crstatic(2), other(3)

hwStaticLspName		1.3.6.1.4.1.2011.5.25.121.1.5.1.5
Indicates the name of the static LSP or CR-LSP. The name is appointed when the static LSP or CR-LSP is created.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hwStaticLspStatus		1.3.6.1.4.1.2011.5.25.121.1.5.1.6
Indicates the actual operation status of the static LSP/CR-LSP. Options: 1. up(1) -indicates that the static LSP/CR-LSP is in Up state. 2. down(2) -indicates that the static LSP/CR-LSP is in down state. 3. testing(3) -indicates that the static LSP/CR-LSP is used in test mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

hwStaticLspClassType		1.3.6.1.4.1.2011.5.25.121.1.5.1.7
The Class-Type of this static lsp. Options: 1. ct0(1) -indicates that the class type is ct0. 2. ct1(2) -indicates that the class type is ct1. 3. ct2(3) -indicates that the class type is ct2. 4. ct3(4) -indicates that the class type is ct3. 5. ct4(5) -indicates that the class type is ct4. 6. ct5(6) -indicates that the class type is ct5. 7. ct6(7) -indicates that the class type is ct6. 8. ct7(8) -indicates that the class type is ct7. 9. none(9) -indicates that the class type is unconfiged.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ct0(1), ct1(2), ct2(3), ct3(4), ct4(5), ct5(6), ct6(7), ct7(8), none(9)

hwStaticLspBandwidth		1.3.6.1.4.1.2011.5.25.121.1.5.1.8
The bandwidth of this static lsp. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTeClassTable		1.3.6.1.4.1.2011.5.25.121.1.6
TE-class mapping is a set of a maximum of eight TE-class items. TE-class is a pair, such as TE-Class[1] = . A (setup/holding) priority associated with an LSP valid only if it appears as a pair with the Class-Type. Class-Types and priorities can be randomly paired up. You can define a maximum of eight pairs. The LSR is considered to support a particular Class-Type only if it appears in the definition of the eight possible TE-Classes. It is suggested that all the LSRs in the domain use the same TE-Class mapping. The index of this table is hwMplsTeClassId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsTeClassEntry

hwMplsTeClassEntry		1.3.6.1.4.1.2011.5.25.121.1.6.1
TE-class mapping is a set of a maximum of eight TE-class items. TE-class is a pair, such as TE-Class[1] = . A (setup/holding) priority associated with an LSP valid only if it appears as a pair with the Class-Type. Class-Types and priorities can be randomly paired up. You can define a maximum of eight pairs. The LSR is considered to support a particular Class-Type only if it appears in the definition of the eight possible TE-Classes. It is suggested that all the LSRs in the domain use the same TE-Class mapping. The index of this entry is hwMplsTeClassId.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsTeClassEntry

hwMplsTeClassId		1.3.6.1.4.1.2011.5.25.121.1.6.1.1
This value represents the index of the TE-Class configured on this LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwMplsTeClassClassType		1.3.6.1.4.1.2011.5.25.121.1.6.1.2
This value represents a Class-Type supported on the LSR. Options: 1. ct0(1) -indicates that the class type of static CR-LSP is ct0. 2. ct1(2) -indicates that the class type of static CR-LSP is ct1. 3. ct2(3) -indicates that the class type of static CR-LSP is ct2. 4. ct3(4) -indicates that the class type of static CR-LSP is ct3. 5. ct4(5) -indicates that the class type of static CR-LSP is ct4. 6. ct5(6) -indicates that the class type of static CR-LSP is ct5. 7. ct6(7) -indicates that the class type of static CR-LSP is ct6. 8. ct7(8) -indicates that the class type of static CR-LSP is ct7.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ct0(1), ct1(2), ct2(3), ct3(4), ct4(5), ct5(6), ct6(7), ct7(8)

hwMplsTeClassPriority		1.3.6.1.4.1.2011.5.25.121.1.6.1.3
This value represents the preemption priority (setup or holding) supported for a particular class-type, on the LSR. Range: 0-7 Default: 7
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTeClassDescription		1.3.6.1.4.1.2011.5.25.121.1.6.1.4
Textual description of the TE-Class defined by this row.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hwMplsIfBcTable		1.3.6.1.4.1.2011.5.25.121.1.7
This table describes bandwidth constraints associated with MPLS TE enabled interfaces. The index of this table is ifIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsIfBcEntry

hwMplsIfBcEntry		1.3.6.1.4.1.2011.5.25.121.1.7.1
This table describes bandwidth constraints associated with MPLS TE enabled interfaces. The index of this entry is ifIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsIfBcEntry

hwMplsIfMaxResvBandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.1
The maximum reservable bandwidth on this interface. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsIfBc0Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.2
The bandwidth of Class-Type 0 (CT0) in this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsIfBc1Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.3
The bandwidth of Class-Type 1 (CT1) in this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsIfBc2Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.4
The bandwidth of Class-Type 2 (CT2) in this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsIfBc3Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.5
The bandwidth of Class-Type 3 (CT3) in this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsIfBc4Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.6
The bandwidth of Class-Type 4 (CT4) in this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsIfBc5Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.7
The bandwidth of Class-Type 5 (CT5) in this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsIfBc6Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.8
The bandwidth of Class-Type 6 (CT6) in this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsIfBc7Bandwidth		1.3.6.1.4.1.2011.5.25.121.1.7.1.9
The bandwidth of Class-Type 7 (CT7) in this tunnel. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwStaticLspTnlTable		1.3.6.1.4.1.2011.5.25.121.1.8
hwStaticLspTnlTable is used to display static LSP token of a static LSP of a specified name. The index of this table is hwStaticLspTnlName.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwStaticLspTnlEntry

hwStaticLspTnlEntry		1.3.6.1.4.1.2011.5.25.121.1.8.1
hwStaticLspTnlTable is used to display static LSP token of a static LSP of a specified name. The index of this entry is hwStaticLspTnlName.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwStaticLspTnlEntry

hwStaticLspTnlName		1.3.6.1.4.1.2011.5.25.121.1.8.1.1
Indicates the name of the Static Lsp.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString

hwStaticLspTnlToken		1.3.6.1.4.1.2011.5.25.121.1.8.1.2
Indicates the token of the Static Lsp.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTeVpnQosTable		1.3.6.1.4.1.2011.5.25.121.1.9
This table is used to display VPN QoS information of a specified TE Tunnel according to TunnelID. The index of this table is hwMplsTnlID.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsTeVpnQosEntry

hwMplsTeVpnQosEntry		1.3.6.1.4.1.2011.5.25.121.1.9.1
This table is used to display VPN QoS information of a specified TE Tunnel according to TunnelID. The index of this entry is hwMplsTnlID.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsTeVpnQosEntry

hwMplsTnlID		1.3.6.1.4.1.2011.5.25.121.1.9.1.1
The value of this object identifies the TE tunnel ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwMplsTeVpnMaxBandwidth		1.3.6.1.4.1.2011.5.25.121.1.9.1.2
The value of this object identifies the bandwidth the TE tunnel can provide for VPN QoS. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTeVpnAllocatedBandwidth		1.3.6.1.4.1.2011.5.25.121.1.9.1.3
The value of this object identifies the bandwidth used by VPN QoS, in Kbps. Unit: kbit/s
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwStaticLspInIfIndex		1.3.6.1.4.1.2011.5.25.121.1.11
Indicates the inbound interface index of a static LSP/CR-LSP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OCTET STRING

hwStaticLspInIfName		1.3.6.1.4.1.2011.5.25.121.1.12
Indicates the name of an inbound interface of a static LSP/CR-LSP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OCTET STRING

hwStaticLspDownReason		1.3.6.1.4.1.2011.5.25.121.1.13
Indicates the reason for static LSP/CR-LSP Down: 0. Other 1. Static LSP/CR-LSP up 2. MPLS disabled on an interface 3. MPLS TE disabled on an interface 4. Route change 5. Tunnel binding associated with the static LSP/CR-LSP deleted 6. Static LSP/CR-LSP configuration delete 7. Inbound interface Down 8. Outbound interface Down 9. Tunnel associated with the static LSP/CR-LSP has been shut down 10. Static LSP/CR-LSP configuration update 11. The bound ring is invalid.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsExtendTrap		1.3.6.1.4.1.2011.5.25.121.2
OBJECT IDENTIFIER

hwLspTrap		1.3.6.1.4.1.2011.5.25.121.2.1
OBJECT IDENTIFIER

hwMplsStaticLspUp		1.3.6.1.4.1.2011.5.25.121.2.1.1
This notification indicates that the status of referred static LSP changes to Up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsStaticLspDown		1.3.6.1.4.1.2011.5.25.121.2.1.2
This notification indicates that the status of referred static LSP changes to Down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsStaticCRLspUp		1.3.6.1.4.1.2011.5.25.121.2.1.3
This notification indicates that the status of referred static CR-LSP changes to Up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsStaticCRLspDown		1.3.6.1.4.1.2011.5.25.121.2.1.4
This notification indicates that the status of referred static CR-LSP changes to Down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTeFrrProtAval		1.3.6.1.4.1.2011.5.25.121.2.1.5
This notification indicates that the primary tunnel is bound to bypass tunnel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTeFrrProtNotAval		1.3.6.1.4.1.2011.5.25.121.2.1.6
This notification indicates that the primary tunnel is unbound to bypass tunnel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTeFrrSwitch		1.3.6.1.4.1.2011.5.25.121.2.1.7
This notification indicates that the primary tunnel is switches to the bypass tunnel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTeFrrResume		1.3.6.1.4.1.2011.5.25.121.2.1.8
This notification indicates that the primary tunnel is switched back from the bypass tunnel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelHSBSwitch		1.3.6.1.4.1.2011.5.25.121.2.1.9
This notification indicates that the data is switched from the primary CR-LSP to the HSB CR-LSP.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelHSBResume		1.3.6.1.4.1.2011.5.25.121.2.1.10
This notification indicates that the data is switched from the HSB CR-LSP to the primary CR-LSP.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelOBSwitch		1.3.6.1.4.1.2011.5.25.121.2.1.11
This notification indicates that the primary CR-LSP is down and the Ordinary backup CR-LSP is up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelOBResume		1.3.6.1.4.1.2011.5.25.121.2.1.12
This notification indicates that the data is switched from the Ordinary backup CR-LSP to the primary CR-LSP.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelUp		1.3.6.1.4.1.2011.5.25.121.2.1.13
The hwMplsTunnelUp trap indicates that the staus of the tunnel changes into Up.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelDown		1.3.6.1.4.1.2011.5.25.121.2.1.14
The hwMplsTunnelDown trap indicates that the staus of the tunnel changes into Down.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelChangeBw		1.3.6.1.4.1.2011.5.25.121.2.1.15
This notification indicates that the bandwidth of the tunnel is changed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelTpOamLossSD		1.3.6.1.4.1.2011.5.25.121.2.1.16
This object indicates that the loss ratio of the packets carried by the tunnel exceeded the first threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamSDRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.17
This object indicates that the loss ratio of the packets carried by the tunnel dropped below the first threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamLoss		1.3.6.1.4.1.2011.5.25.121.2.1.18
This object indicates that TP OAM detected tunnel connectivity faults.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamLossRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.19
This object indicates that TP OAM did not detect tunnel connectivity faults.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamAis		1.3.6.1.4.1.2011.5.25.121.2.1.20
This object indicates that TP OAM detected an alarm indication signal.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamAisRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.21
This object indicates that TP OAM no longer detected alarm indication signals.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamRdi		1.3.6.1.4.1.2011.5.25.121.2.1.22
This object indicates that TP OAM detected remote defects.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamRdiRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.23
This object indicates that the remote defects detected by TP OAM were removed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamMeg		1.3.6.1.4.1.2011.5.25.121.2.1.24
This object indicates that the names configured on the two ends of the tunnel are inconsistent.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamMegRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.25
This object indicates that the names configured on the two ends of the tunnel now are consistent.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamMep		1.3.6.1.4.1.2011.5.25.121.2.1.26
This object indicates that the MEP-IDs configured on the two ends of the tunnel are inconsistent.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamMepRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.27
This object indicates that the MEP-IDs configured on the two ends of the tunnel now are consistent.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamSF		1.3.6.1.4.1.2011.5.25.121.2.1.28
This object indicates that the loss ratio of the packets carried by the tunnel exceeded the second threshold in the local link.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamSFRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.29
This object indicates that the loss ratio of the packets carried by the tunnel dropped below the second threshold in the local link.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamPeriod		1.3.6.1.4.1.2011.5.25.121.2.1.30
This object indicates that the TP OAM detection periods on the two ends of the tunnel are inconsistent.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamPeriodRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.31
This object indicates that the TP OAM detection periods on the two ends of the tunnel now are consistent.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamLck		1.3.6.1.4.1.2011.5.25.121.2.1.32
This object indicates that TP OAM detected the service level of the tunnel has been locked.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamLckRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.33
This object indicates that TP OAM detected the service level of the tunnel has not been locked.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamExcess		1.3.6.1.4.1.2011.5.25.121.2.1.34
This object indicates that MPLS OAM detected the tunnel received excess alarm.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamExcessRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.35
This object indicates that MPLS OAM detected the tunnel received excess alarm end.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamMisMatch		1.3.6.1.4.1.2011.5.25.121.2.1.36
This object indicates that MPLS OAM detected the tunnel received MisMatch alarm.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamMisMatchRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.37
This object indicates that MPLS OAM detected the tunnel received MisMatch alarm end.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamMisMerge		1.3.6.1.4.1.2011.5.25.121.2.1.38
This object indicates that MPLS OAM detected the tunnel received MisMerge alarm.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamMisMergeRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.39
This object indicates that MPLS OAM detected the tunnel received MisMerge alarm end.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamUnknown		1.3.6.1.4.1.2011.5.25.121.2.1.40
This object indicates that MPLS OAM detected the tunnel received Unknown alarm.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamUnknownRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.41
This object indicates that MPLS OAM detected the tunnel received Unknown alarm end.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamBDI		1.3.6.1.4.1.2011.5.25.121.2.1.42
This object indicates that MPLS OAM detected the tunnel received BDI alarm.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamBDIRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.43
This object indicates that MPLS OAM detected the tunnel received BDI alarm end.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamFail		1.3.6.1.4.1.2011.5.25.121.2.1.44
This object indicates that MPLS OAM detected the tunnel received OAMFAIL alarm.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamFailRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.45
This object indicates that MPLS OAM detected the tunnel received OAMFAIL alarm end.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelPrimaryUp		1.3.6.1.4.1.2011.5.25.121.2.1.46
This notification indicates that the status of the RSVP-TE Primary LSP changes to Up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelPrimaryDown		1.3.6.1.4.1.2011.5.25.121.2.1.47
This notification indicates that the status of the RSVP-TE Primary LSP changes to Down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelHotstandbyUp		1.3.6.1.4.1.2011.5.25.121.2.1.48
This notification indicates that the status of the RSVP-TE Hot-standby LSP changes to Up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelHotstandbyDown		1.3.6.1.4.1.2011.5.25.121.2.1.49
This notification indicates that the status of the RSVP-TE Hot-standby LSP changes to Down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelOrdinaryUp		1.3.6.1.4.1.2011.5.25.121.2.1.50
This notification indicates that the status of the RSVP-TE Ordinary LSP changes to Up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelOrdinaryDown		1.3.6.1.4.1.2011.5.25.121.2.1.51
This notification indicates that the status of the RSVP-TE Ordinary LSP changes to Down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelBesteffortUp		1.3.6.1.4.1.2011.5.25.121.2.1.52
This notification indicates that the status of the RSVP-TE Best-effort LSP changes to Up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelBesteffortDown		1.3.6.1.4.1.2011.5.25.121.2.1.53
This notification indicates that the status of the RSVP-TE Best-effort LSP changes to Down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTeAutoTunnelDownClear		1.3.6.1.4.1.2011.5.25.121.2.1.54
This notification indicates that the TE Auto tunnel Down alarm was cleared.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTeAutoTunnelPrimaryDownClear		1.3.6.1.4.1.2011.5.25.121.2.1.55
This notification indicates that the Down alarm about the primary LSP in the TE Auto tunnel was cleared.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelBBSwitch		1.3.6.1.4.1.2011.5.25.121.2.1.56
This notification indicates that the primary CR-LSP is Down and the Best-effort backup CR-LSP is Up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelBBResume		1.3.6.1.4.1.2011.5.25.121.2.1.57
This notification indicates that data is switched from the Best-effort backup CR-LSP to the primary CR-LSP.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsExtTunnelDown		1.3.6.1.4.1.2011.5.25.121.2.1.58
This notification indicates that the status of te tunnel changes to Down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsExtTunnelDownClear		1.3.6.1.4.1.2011.5.25.121.2.1.59
This notification indicates that the down alarm of te tunnel was cleared.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamLocalLock		1.3.6.1.4.1.2011.5.25.121.2.1.60
This object indicates that TP OAM detected the tunnel has been locked.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsOamLocalLockRecovery		1.3.6.1.4.1.2011.5.25.121.2.1.61
This object indicates that TP OAM detected the tunnel has not been locked.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelDelete		1.3.6.1.4.1.2011.5.25.121.2.1.62
This notification indicates that the mpls te tunnel was deleted.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsLspThresholdExceed		1.3.6.1.4.1.2011.5.25.121.2.1.63
This object indicates that lsp count has exceeded the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsLspThresholdExceedClear		1.3.6.1.4.1.2011.5.25.121.2.1.64
This object indicates that lsp count has resumed from exceeding the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsLspTotalCountExceed		1.3.6.1.4.1.2011.5.25.121.2.1.65
This object indicates that lsp count has reached the total count.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsLspTotalCountExceedClear		1.3.6.1.4.1.2011.5.25.121.2.1.66
This object indicates that lsp count has resumed from reaching the total count.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsDynamicLabelThresholdExceed		1.3.6.1.4.1.2011.5.25.121.2.1.67
This object indicates that label usage has exceeded the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsDynamicLabelThresholdExceedClear		1.3.6.1.4.1.2011.5.25.121.2.1.68
This object indicates that label usage has resumed from exceeding the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsDynamicLabelTotalCountExceed		1.3.6.1.4.1.2011.5.25.121.2.1.69
This object indicates that label count has reached the total count.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsDynamicLabelTotalCountExceedClear		1.3.6.1.4.1.2011.5.25.121.2.1.70
This object indicates that label usage count has resumed from reaching the total count.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsResourceThresholdExceed		1.3.6.1.4.1.2011.5.25.121.2.1.71
This object indicates that the number of MPLS resources has exceeded the upper threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsResourceThresholdExceedClear		1.3.6.1.4.1.2011.5.25.121.2.1.72
This object indicates that the number of MPLS resources has fallen below the lower threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsResourceTotalCountExceed		1.3.6.1.4.1.2011.5.25.121.2.1.73
This object indicates that the number of MPLS resources has reached the maximum number.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsResourceTotalCountExceedClear		1.3.6.1.4.1.2011.5.25.121.2.1.74
This object indicates that the number of MPLS resources fallen below the recovery number.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsLspLoopBack		1.3.6.1.4.1.2011.5.25.121.2.1.75
This object indicates that the lsp was looped back.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsLspLoopBackClear		1.3.6.1.4.1.2011.5.25.121.2.1.76
This object indicates that loopback of the LSP is restored.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelCommitLost		1.3.6.1.4.1.2011.5.25.121.2.1.77
This object indicates that, after the device saves MPLS TE tunnel configurations, the device commits only some MPLS tunnel configurations.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTunnelCommitLostClear		1.3.6.1.4.1.2011.5.25.121.2.1.78
This object indicates that, after the device saves MPLS TE tunnel configurations, the device commits all MPLS tunnel configurations.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsTrapObjects		1.3.6.1.4.1.2011.5.25.121.2.2
OBJECT IDENTIFIER

hwMplsTunnelIfName		1.3.6.1.4.1.2011.5.25.121.2.2.1
The Tunnel Interface name.
Status: obsolete	Access: accessible-for-notify
OBJECT-TYPE
	SnmpAdminString

hwMplsTunnelFrrConfigOper		1.3.6.1.4.1.2011.5.25.121.2.2.2
The value of this object identifies the operation that an FRR configuration is committed on the tunnel. Options: 1.unconfig(0) -indicates the configuration of the undo mpls te fast-reroute command is committed. 2.config(1) -indicates the configuration of the mpls te fast-reroute command is committed. 3.unknow(2) -indicates an unknown operation.
Status: obsolete	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	unconfig(0), config(1), unknow(2)

hwMplsTunnelDownReason		1.3.6.1.4.1.2011.5.25.121.2.2.3
Indicates the alarm reason as below: 1. Other; 2. Static LSP down; 3. Static CR-LSP down; 4. The out interface of the RSVP LSP ingress is down; 5. The resource of RSVP LSP is preempted; 6. RSVP message timeout; 7. RSVP neighbor lost; 8. The bypass-tunnel is down or is unbinded with main tunnel, as bypass-tunnel is in used; 9. CSPF compute fail; 10.User shutdown the tunnel; 11.TPOAM indicates the connectivity fault of the link; 12.TPOAM indicates receive alarm indication signal defect of the link; 13.TPOAM indicates the remote defect of the link; 14.TPOAM indicates receive unexpected MEG-ID defect of the link; 15.TPOAM indicates receive unexpected MEP-ID defect of the link; 16.TPOAM indicates packet lost exceed signal fault threshold in the local link; 17.TPOAM indicates packet unexpected period defect of the link; 18.MPLS OAM connectivity fault; 19.MPLS OAM TTSI excess; 20.MPLS OAM TTSI mismatch; 21.MPLS OAM TTSI merge error; 22.MPLS OAM unknown error; 23.MPLS OAM BDI; 24.MPLS OAM FDI; 25.MPLS OAM signal fail; 26.MPLS OAM signal degrade; 27.MPLS OAM fail; 28.Service resume; 29.Service delete; 100. Clear.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	other(1), staticLspDown(2), staticCrlspDown(3), outIfDown(4), resourcePreempted(5), rsvpMessageTimeout(6), rsvpNeighborLost(7), bypassTunnelDownOrUnbinded(8), cspfComputeFail(9), userShutdown(10), tpoamLossOfContinuity(11), tpoamAlarmIndicationSignal(12), tpoamRemoteDefectIndication(13), tpoamUnexpectedMEG(14), tpoamUnexpectedMEP(15), tpoamLossSF(16), tpoamPeriod(17), mplsOamLocv(18), mplsOamExcess(19), mplsOamMisMatch(20), mplsOamMisMerge(21), mplsOamUnknown(22), mplsOamBdi(23), mplsOamFdi(24), mplsOamSF(25), mplsOamSD(26), mplsOamDOamFail(27), serviceResume(28), serviceDelete(29), clear(100)

hwMplsLspProtocol		1.3.6.1.4.1.2011.5.25.121.2.2.4
The value of this object identifies the protocol of the lsp which exceeds the threshold or total count. Options: 1.ldp(1) -indicates the lsp is ldp lsp. 2.bgp(2) -indicates the lsp is bgp lsp. 3.bgpv6(3) -indicates the lsp is bgpv6 lsp. 4.ldpfrr(4) -indicates the lsp is ldp frr lsp. 5.rsvp(5) -indicates the lsp is rsvp te lsp. 6.totalLsp(6) -indicates the lsp is total lsp. 7.totalCrLsp(7) -indicates the lsp is total cr-lsp. 8.ldpIngress(8) -indicates the lsp is ldp ingress lsp. 9.ldpTransit(9) -indicates the lsp is ldp transit lsp. 10.ldpEgress(10) -indicates the lsp is ldp egress lsp. 11.bgpIngress(11) -indicates the lsp is bgp ingress lsp. 12.bgpEgress(12) -indicates the lsp is bgp egress lsp. 13.bgpv6Ingress(13) -indicates the lsp is bgpv6 ingress lsp. 14.bgpv6Egress(14) -indicates the lsp is bgpv6 egress lsp. 15.rsvpIngress(15) -indicates the lsp is rsvp te ingress lsp. 16.rsvpTransit(16) -indicates the lsp is rsvp te transit lsp. 17.rsvpEgress(17) -indicates the lsp is rsvp te egress lsp. 18.totalLspIngress(18) -indicates the lsp is total ingress lsp. 19.totalLspTransit(19) -indicates the lsp is total transit lsp. 20.totalLspEgress(20) -indicates the lsp is total egress lsp. 21.totalCrLspIngress(21) -indicates the lsp is total ingress cr-lsp. 22.totalCrLspTransit(22) -indicates the lsp is total transit cr-lsp. 23.totalCrLspEgress(23) -indicates the lsp is total egress cr-lsp. 24.totalPublicNetLspIngressTransit(24) -indicates the lsp is total ingress and transit public netwrok lsp. 25.totalPublicNetLspTransitEgress(25) -indicates the lsp is total transit and egress public network cr-lsp. 26.privateNetBgp(26) -indicates the lsp is private network bgp lsp. 27.unknown(100) -indicates the lsp type is unknown.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	ldp(1), bgp(2), bgpv6(3), ldpfrr(4), rsvp(5), totalLsp(6), totalCrLsp(7), ldpIngress(8), ldpTransit(9), ldpEgress(10), bgpIngress(11), bgpEgress(12), bgpv6Ingress(13), bgpv6Egress(14), rsvpIngress(15), rsvpTransit(16), rsvpEgress(17), totalLspIngress(18), totalLspTransit(19), totalLspEgress(20), totalCrLspIngress(21), totalCrLspTransit(22), totalCrLspEgress(23), totalPublicNetLspIngressTransit(24), totalPublicNetLspTransitEgress(25), privateNetBgp(26), unknown(100)

hwMplsLspThreshold		1.3.6.1.4.1.2011.5.25.121.2.2.5
The value of this object identifies the threshold of the lsp.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsLspTotalCount		1.3.6.1.4.1.2011.5.25.121.2.2.6
The value of this object identifies the total permit count of lsp.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsLspCurrentCount		1.3.6.1.4.1.2011.5.25.121.2.2.7
The value of this object identifies the current count of the lsp.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsTunnelDownLSRID		1.3.6.1.4.1.2011.5.25.121.2.2.8
The value of this object identifies the LSR ID of the error node on a tunnel.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MplsLsrIdentifier

hwMplsTunnelDownIfIpAddr		1.3.6.1.4.1.2011.5.25.121.2.2.9
The value of this object identifies the IP address of the error interface on a tunnel.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	InetAddress

hwMplsTunnelDownIfIpAddrType		1.3.6.1.4.1.2011.5.25.121.2.2.10
The value of this object identifies the IP address type of the error interface on a tunnel.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	InetAddressType

hwMplsResourceType		1.3.6.1.4.1.2011.5.25.121.2.2.11
The value of this object identifies that the number of MPLS resources has exceeded the threshold or the maximum number. Options: 1.autoBypassTunnelIf(1) -Indicates that the resource is auto bypass tunnel interface. 2.p2mpAutoTunnelIf(2) -Indicates that the resource is P2MP auto tunnel interface. 3.teBfd(3) -Indicates that the resource is dynamic BFD for TE LSP. 4.ldpBfd(4) -Indicates that the resource is dynamic BFD for LDP LSP. 5.mldpTotalTree(5) -Indicates that the resource is the total number of MLDP trees. 6.mldpTotalBranch(6) -Indicates that the resource is the total number of MLDP branches. 7.ldpTotalRemoteAdjacency(7) -Indicates that the resource is LDP total remote adjacency. 8.outSegment(8) -Indicates that the resource is LDP outSegment. 9.autoPrimaryTunnelIf(9) -Indicates that the resource is auto primary tunnel interface. 10.ldpTotalLocalAdjacency(10) -Indicates that the resource is LDP total local adjacency. 11.unknown(100) -Indicates that the resource type is unknown.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	autoBypassTunnelIf(1), p2mpAutoTunnelIf(2), teBfd(3), ldpBfd(4), mldpTotalTree(5), mldpTotalBranch(6), ldpTotalRemoteAdjacency(7), outSegment(8), autoPrimaryTunnelIf(9), ldpTotalLocalAdjacency(10), unknown(100)

hwMplsResourceCurrentCount		1.3.6.1.4.1.2011.5.25.121.2.2.12
The value of this object identifies the number of the resources.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsResourceThreshold		1.3.6.1.4.1.2011.5.25.121.2.2.13
The value of this object identifies the threshold for the number of the resources.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsResourceTotalCount		1.3.6.1.4.1.2011.5.25.121.2.2.14
The value of this object identifies the maximum number of allowed resources.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsSessionTunnelId		1.3.6.1.4.1.2011.5.25.121.2.2.15
The value of this object identifies the Tunnel ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsLocalLspId		1.3.6.1.4.1.2011.5.25.121.2.2.16
The value of this object identifies the LSP ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsIngressLsrId		1.3.6.1.4.1.2011.5.25.121.2.2.17
The value of this object identifies the ingress LSR ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsEgressLsrId		1.3.6.1.4.1.2011.5.25.121.2.2.18
The value of this object identifies the egress LSR ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwMplsLspName		1.3.6.1.4.1.2011.5.25.121.2.2.19
This object indicates the name of an bidirectional static CR-LSP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	SnmpAdminString

hwMplsTunnelFrrConfigChange		1.3.6.1.4.1.2011.5.25.121.2.3
When the trap indicating that TE-Frr configuration of Tunnel is changed is sent, the cause for the change of TE-FRR configuration of Tunnel is displayed.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

hwMplsGlobalObject		1.3.6.1.4.1.2011.5.25.121.3
OBJECT IDENTIFIER

hwMplsGlobalWorkMode		1.3.6.1.4.1.2011.5.25.121.3.1
The work mode of DS-TE system, default mode is nonstandard. Options: 1. standard(1) -indicates work mode of DS-TE system is standard 2. nonstandard(2) -indicates work mode of DS-TE system is nonstandard
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	standard(1), nonstandard(2)

hwMplsGlobalBcModel		1.3.6.1.4.1.2011.5.25.121.3.2
Bandwidth Constraint Model currently used by this LSR. Options: 1. rdm(1) -indicates that the bandwidth constraint model is RDM. 2. mam(2) -indicates that the bandwidth constraint model is MAM. 3. extendMam(3) -indicates that the bandwidth constraint model is ExtendMam.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rdm(1), mam(2), extendMam(3)

hwMplsDynamicLabelTotalCount		1.3.6.1.4.1.2011.5.25.121.3.3
The value of this object identifies the total permit count of dynamic label.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsDynamicLabelCurrentCount		1.3.6.1.4.1.2011.5.25.121.3.4
The value of this object identifies the current count of the dynamic label.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsDynamicLabelThresholdUpperLimit		1.3.6.1.4.1.2011.5.25.121.3.5
The upper limit threshold value (%) of dynamic label, default value is 80.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsDynamicLabelThresholdLowerLimit		1.3.6.1.4.1.2011.5.25.121.3.6
The lower limit threshold value (%) of dynamic label, default value is 70.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsLspStatistics		1.3.6.1.4.1.2011.5.25.121.4
OBJECT IDENTIFIER

hwMplsLspStatisticsTable		1.3.6.1.4.1.2011.5.25.121.4.1
hwMplsLspStatisticsTable is used to display the number of ingress LSPs, transit LSPs, or egress LSPs of specified types. The index of this table is hwMplsLspStatisticsLspType.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsLspStatisticsEntry

hwMplsLspStatisticsEntry		1.3.6.1.4.1.2011.5.25.121.4.1.1
hwMplsLspStatisticsTable is used to display the number of ingress LSPs, transit LSPs, or egress LSPs of specified types. The index of this entry is hwMplsLspStatisticsLspType.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsLspStatisticsEntry

hwMplsLspStatisticsLspType		1.3.6.1.4.1.2011.5.25.121.4.1.1.1
This object indicates the LSP type. Options: 1. staticLsp(1) -indicates the static LSP. 2. staticCrLsp(2) -indicates the static CR-LSP. 3. ldpLsp(3) -indicates the LDP LSP. 4. rsvpCrLsp(4) -indicates the RSVP LSP. 5. bgpLsp(5) -indicates the BGP LSP. 6. asbrLsp(6) -indicates the ASBR LSP. 7. bgpIpv6Lsp(7) -indicates the BGP IPv6 LSP. 8. l3vpnIpv6Lsp(8)-indicates the L3VPN IPv6 LSP.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	staticLsp(1), staticCrLsp(2), ldpLsp(3), rsvpCrLsp(4), bgpLsp(5), asbrLsp(6), bgpIpv6Lsp(7), l3vpnIpv6Lsp(8)

hwMplsLspStatisticsIngressLspCount		1.3.6.1.4.1.2011.5.25.121.4.1.1.2
This object indicates the number of ingress LSPs of a specified type.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsLspStatisticsTransitLspCount		1.3.6.1.4.1.2011.5.25.121.4.1.1.3
This object indicates the number of transit LSPs of a specified type.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsLspStatisticsEgressLspCount		1.3.6.1.4.1.2011.5.25.121.4.1.1.4
This object indicates the number of egress LSPs of a specified type.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsLspStatisticsTotalLspCount		1.3.6.1.4.1.2011.5.25.121.4.1.1.5
This object indicates the total number of the ingress LSPs, transit LSPs and egress LSP of specified types.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsTrafficStatisticsStaticLspTable		1.3.6.1.4.1.2011.5.25.121.4.2
Indicates the traffic statistics of a LSP. The indexes of this table is hwMplsTrafficStatisticsStaticLspName.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsTrafficStatisticsStaticLspEntry

hwMplsTrafficStatisticsStaticLspEntry		1.3.6.1.4.1.2011.5.25.121.4.2.1
Indicates the traffic statistics of a LSP. The indexes of this entry is hwMplsTrafficStatisticsStaticLspName.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsTrafficStatisticsStaticLspEntry

hwMplsTrafficStatisticsStaticLspName		1.3.6.1.4.1.2011.5.25.121.4.2.1.1
Indicates the name of the static LSP or CR-LSP. The name is appointed when the static LSP or CR-LSP is created.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString

hwMplsTrafficStatisticsStaticLspForwardInBytes		1.3.6.1.4.1.2011.5.25.121.4.2.1.2
An estimate of the forward of bistatic LSP's current incoming traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: bytes
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hwMplsTrafficStatisticsStaticLspForwardInPackets		1.3.6.1.4.1.2011.5.25.121.4.2.1.3
An estimate of the forward of bistatic LSP's current incoming traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: packets
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hwMplsTrafficStatisticsStaticLspForwardOutBytes		1.3.6.1.4.1.2011.5.25.121.4.2.1.4
An estimate of the forward of bistatic LSP's current outgoing traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: bytes
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hwMplsTrafficStatisticsStaticLspForwardOutPackets		1.3.6.1.4.1.2011.5.25.121.4.2.1.5
An estimate of the forward of bistatic LSP's current outgoing traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: packets
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hwMplsTrafficStatisticsStaticLspBackwardInBytes		1.3.6.1.4.1.2011.5.25.121.4.2.1.6
An estimate of the backward of bistatic LSP's current incoming traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: bytes
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hwMplsTrafficStatisticsStaticLspBackwardInPackets		1.3.6.1.4.1.2011.5.25.121.4.2.1.7
An estimate of the backward of bistatic LSP's current incoming traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: packets
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hwMplsTrafficStatisticsStaticLspBackwardOutBytes		1.3.6.1.4.1.2011.5.25.121.4.2.1.8
An estimate of the backward of bistatic LSP's current outgoing traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: bytes
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hwMplsTrafficStatisticsStaticLspBackwardOutPackets		1.3.6.1.4.1.2011.5.25.121.4.2.1.9
An estimate of the backward of bistatic LSP's current outgoing traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: packets
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hwMplsExtendConformance		1.3.6.1.4.1.2011.5.25.121.6
OBJECT IDENTIFIER

hwMplsExtendGroups		1.3.6.1.4.1.2011.5.25.121.6.1
OBJECT IDENTIFIER

hwMplsTunnelGroup		1.3.6.1.4.1.2011.5.25.121.6.1.1
Indicate the atrributes of the tunnel.
Status: current	Access: read-only
OBJECT-GROUP

hwStaticLspGroup		1.3.6.1.4.1.2011.5.25.121.6.1.2
Indicate the atrributes of the static lsp.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsDsTeGroup		1.3.6.1.4.1.2011.5.25.121.6.1.3
Indicate the atrributes about DS-TE.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsLspStatisticsGroup		1.3.6.1.4.1.2011.5.25.121.6.1.4
Indicate LSP statistics.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsObsoleteGroup		1.3.6.1.4.1.2011.5.25.121.6.1.5
Indicate the OBSOLETE objects of MPLS.
Status: obsolete	Access: read-only
OBJECT-GROUP

hwMplsTrapGroup		1.3.6.1.4.1.2011.5.25.121.6.1.6
For mpls trap object.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsRingGroup		1.3.6.1.4.1.2011.5.25.121.6.1.7
For mpls ring trap object.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsGlobalGroup		1.3.6.1.4.1.2011.5.25.121.6.1.8
For mpls global object.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsLspGroup		1.3.6.1.4.1.2011.5.25.121.6.1.9
For mpls lsp object.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsLspTrafficStatisticGroup		1.3.6.1.4.1.2011.5.25.121.6.1.10
Indicate the traffic statistic of the LSP.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsResourceGroup		1.3.6.1.4.1.2011.5.25.121.6.1.11
For mpls resource object.
Status: current	Access: read-only
OBJECT-GROUP

hwMplsExtendCompliances		1.3.6.1.4.1.2011.5.25.121.6.2
OBJECT IDENTIFIER

hwExtendTrapGroup		1.3.6.1.4.1.2011.5.25.121.6.2.1
Indicate the traps.
Status: current	Access: read-only
NOTIFICATION-GROUP

hwObsoleteTrapGroup		1.3.6.1.4.1.2011.5.25.121.6.2.2
Indicate the Obsolete traps.
Status: obsolete	Access: read-only
NOTIFICATION-GROUP

hwMplsModuleCompliance		1.3.6.1.4.1.2011.5.25.121.6.2.3
hwMplsModuleCompliance
Status: current	Access: read-only
MODULE-COMPLIANCE

hwMplsRingMib		1.3.6.1.4.1.2011.5.25.121.7
OBJECT IDENTIFIER

hwMplsRingTable		1.3.6.1.4.1.2011.5.25.121.7.1
Indicates the table information of the MPLS ring.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwMplsRingEntry

hwMplsRingEntry		1.3.6.1.4.1.2011.5.25.121.7.1.1
Indicates the table information of the MPLS ring.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwMplsRingEntry

hwMplsRingID		1.3.6.1.4.1.2011.5.25.121.7.1.1.1
Indicates the ID of the MPLS ring.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hwMplsRingNodeID		1.3.6.1.4.1.2011.5.25.121.7.1.1.2
Indicates the ID of the current Node on the MPLS ring.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwMplsRingName		1.3.6.1.4.1.2011.5.25.121.7.1.1.3
Indicates the name of MPLS ring.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hwMplsRingDirection		1.3.6.1.4.1.2011.5.25.121.7.1.1.4
Indicates the direction of the MPLS ring.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hwMplsRingSwitchReason		1.3.6.1.4.1.2011.5.25.121.7.1.1.5
Indicates the switch reason of the MPLS ring.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hwMplsRingTrap		1.3.6.1.4.1.2011.5.25.121.7.2
OBJECT IDENTIFIER

hwMplsRingSwitch		1.3.6.1.4.1.2011.5.25.121.7.2.1
The notification indicates that the MPLS ring switched.
Status: obsolete	Access: read-only
NOTIFICATION-TYPE

hwMplsRingResume		1.3.6.1.4.1.2011.5.25.121.7.2.2
The notification indicates that the MPLS ring resumed.
Status: obsolete	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamLoss		1.3.6.1.4.1.2011.5.25.121.7.2.3
The notification indicates that no expected CV/FFD packet is received for three consecutive cycles in the west of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamLossClear		1.3.6.1.4.1.2011.5.25.121.7.2.4
The notification indicates that the hwMplsRingWestOamLoss alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamLoss		1.3.6.1.4.1.2011.5.25.121.7.2.5
The notification indicates that no expected CV/FFD packet is received for three consecutive cycles in the east of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamLossClear		1.3.6.1.4.1.2011.5.25.121.7.2.6
The notification indicates that the hwMplsRingEastOamLoss alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamRDI		1.3.6.1.4.1.2011.5.25.121.7.2.7
The notification indicates that RDI packets are received in the west of the MPLS ring, indicating that a fault occurs on the forward ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamRDIClear		1.3.6.1.4.1.2011.5.25.121.7.2.8
The notification indicates that the hwMplsRingWestOamRDI alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamRDI		1.3.6.1.4.1.2011.5.25.121.7.2.9
The notification indicates that RDI packets are received in the east of the MPLS ring, indicating that a fault occurs on the forward ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamRDIClear		1.3.6.1.4.1.2011.5.25.121.7.2.10
The notification indicates that the hwMplsRingEastOamRDI alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamUnexpectedMEG		1.3.6.1.4.1.2011.5.25.121.7.2.11
The notification indicates that a CCM frame carrying a correct MEG level but incorrect MEG ID is received in the west of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamUnexpectedMEGClear		1.3.6.1.4.1.2011.5.25.121.7.2.12
The notification indicates that the hwMplsRingWestOamUnexpectedMEG alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamUnexpectedMEG		1.3.6.1.4.1.2011.5.25.121.7.2.13
The notification indicates that a CCM frame carrying a correct MEG level but incorrect MEG ID is received in the east of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamUnexpectedMEGClear		1.3.6.1.4.1.2011.5.25.121.7.2.14
The notification indicates that the hwMplsRingEastOamUnexpectedMEG alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamUnexpectedPeriod		1.3.6.1.4.1.2011.5.25.121.7.2.15
The notification indicates that a CCM frame carrying a correct MEG level, MEG ID, and MEP ID but incorrect period value is received in the west MEP of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamUnexpectedPeriodClear		1.3.6.1.4.1.2011.5.25.121.7.2.16
The notification indicates that the hwMplsRingWestOamUnexpectedPeriod alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamUnexpectedPeriod		1.3.6.1.4.1.2011.5.25.121.7.2.17
The notification indicates that a CCM frame carrying a correct MEG level, MEG ID, and MEP ID but incorrect period value is received in the east MEP of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamUnexpectedPeriodClear		1.3.6.1.4.1.2011.5.25.121.7.2.18
The notification indicates that the hwMplsRingEastOamUnexpectedPeriod alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamExcess		1.3.6.1.4.1.2011.5.25.121.7.2.19
The notification indicates that five or more CV/FFD packets are correctly received within three consecutive cycles in the west of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamExcessClear		1.3.6.1.4.1.2011.5.25.121.7.2.20
The notification indicates that the hwMplsRingWestOamExcess alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamExcess		1.3.6.1.4.1.2011.5.25.121.7.2.21
The notification indicates that five or more CV/FFD packets are correctly received within three consecutive cycles in the east of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamExcessClear		1.3.6.1.4.1.2011.5.25.121.7.2.22
The notification indicates that the hwMplsRingEastOamExcess alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamSD		1.3.6.1.4.1.2011.5.25.121.7.2.23
The notification indicates that the number of packets for connectivity check received in the west of the MPLS ring is smaller than the SD threshold.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamSDClear		1.3.6.1.4.1.2011.5.25.121.7.2.24
The notification indicates that the hwMplsRingWestOamSD alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamSD		1.3.6.1.4.1.2011.5.25.121.7.2.25
The notification indicates that the number of packets for connectivity check received in the east of the MPLS ring is smaller than the SD threshold.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamSDClear		1.3.6.1.4.1.2011.5.25.121.7.2.26
The notification indicates that the hwMplsRingEastOamSD alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamSF		1.3.6.1.4.1.2011.5.25.121.7.2.27
The notification indicates that the number of packets for connectivity check received in the west of the MPLS ring is smaller than the SF threshold.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamSFClear		1.3.6.1.4.1.2011.5.25.121.7.2.28
The notification indicates that the hwMplsRingWestOamSF alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamSF		1.3.6.1.4.1.2011.5.25.121.7.2.29
The notification indicates that the number of packets for connectivity check received in the east of the MPLS ring is smaller than the SF threshold.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamSFClear		1.3.6.1.4.1.2011.5.25.121.7.2.30
The notification indicates that the hwMplsRingEastOamSF alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestAPSSwitch		1.3.6.1.4.1.2011.5.25.121.7.2.31
The notification indicates that APS switching occurs in the west of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestAPSResume		1.3.6.1.4.1.2011.5.25.121.7.2.32
The notification indicates that APS switches back in the west of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastAPSSwitch		1.3.6.1.4.1.2011.5.25.121.7.2.33
The notification indicates that APS switching occurs in the east of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastAPSResume		1.3.6.1.4.1.2011.5.25.121.7.2.34
The notification indicates that APS switches back in the east of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestAPSSwitchFail		1.3.6.1.4.1.2011.5.25.121.7.2.35
The notification indicates that the remote APS switching fails in the west of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestAPSSwitchFailClear		1.3.6.1.4.1.2011.5.25.121.7.2.36
The notification indicates that the hwMplsRingWestAPSSwitchFail alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastAPSSwitchFail		1.3.6.1.4.1.2011.5.25.121.7.2.37
The notification indicates that the remote APS switching fails in the east of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastAPSSwitchFailClear		1.3.6.1.4.1.2011.5.25.121.7.2.38
The notification indicates that the hwMplsRingEastAPSSwitchFail alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestAPSLost		1.3.6.1.4.1.2011.5.25.121.7.2.39
The notification indicates that APS packets are missing in the west of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestAPSLostClear		1.3.6.1.4.1.2011.5.25.121.7.2.40
The notification indicates that the hwMplsRingWestAPSLost alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastAPSLost		1.3.6.1.4.1.2011.5.25.121.7.2.41
The notification indicates that APS packets are missing in the east of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastAPSLostClear		1.3.6.1.4.1.2011.5.25.121.7.2.42
The notification indicates that the hwMplsRingEastAPSLost alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestAPSMismatch		1.3.6.1.4.1.2011.5.25.121.7.2.43
The notification indicates that the source ID carried by APS packets received in the west is different from the peer source ID configured for the west state machine on the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestAPSMismatchClear		1.3.6.1.4.1.2011.5.25.121.7.2.44
The notification indicates that the hwMplsRingWestAPSMismatch alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastAPSMismatch		1.3.6.1.4.1.2011.5.25.121.7.2.45
The notification indicates that the source ID carried by APS packets received in the east is different from the peer source ID configured for the east state machine on the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastAPSMismatchClear		1.3.6.1.4.1.2011.5.25.121.7.2.46
The notification indicates that the hwMplsRingEastAPSMismatch alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamUnexpectedMEP		1.3.6.1.4.1.2011.5.25.121.7.2.47
The notification indicates that a CCM frame carrying a correct MEG level and correct MEG ID but not the expected MEP ID is received in the west of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingWestOamUnexpectedMEPClear		1.3.6.1.4.1.2011.5.25.121.7.2.48
The notification indicates that the hwMplsRingWestOamUnexpectedMEP alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamUnexpectedMEP		1.3.6.1.4.1.2011.5.25.121.7.2.49
The notification indicates that a CCM frame carrying a correct MEG level and correct MEG ID but not the expected MEP ID is received in the east of the MPLS ring.
Status: current	Access: read-only
NOTIFICATION-TYPE

hwMplsRingEastOamUnexpectedMEPClear		1.3.6.1.4.1.2011.5.25.121.7.2.50
The notification indicates that the hwMplsRingEastOamUnexpectedMEP alarm was cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE