HUAWEI-LswINF-MIB

File: HUAWEI-LswINF-MIB.mib (54922 bytes)

Imported modules

SNMPv2-TC SNMPv2-SMI RFC1213-MIB
HUAWEI-3COM-OID-MIB

Imported symbols

RowStatus DisplayString TruthValue
TEXTUAL-CONVENTION Counter64 MODULE-IDENTITY
OBJECT-TYPE Integer32 IpAddress
TimeTicks OBJECT-IDENTITY Unsigned32
ifEntry ifIndex lswCommon

Defined Types

PortList  
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION    
  OCTET STRING  

VlanIndex  
A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB.
TEXTUAL-CONVENTION    
  Unsigned32 0..4294967295  

InterfaceIndex  
A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
TEXTUAL-CONVENTION    
  Integer32  

DropDirection  
Representing the direction of dropping packets, if applicable.
TEXTUAL-CONVENTION    
  INTEGER disable(1), enableInbound(2), enableOutbound(3), enableBoth(4)  

SpeedModeFlag  
Type of Negotiable Speed mode.
TEXTUAL-CONVENTION    
  BITS s10M(0), s100M(1), s1000M(2), s10000M(3), s24000M(4), s40000M(5), s100000M(6)  

HwIfXXEntry  
SEQUENCE    
  hwifUnBoundPort TruthValue
  hwifISPhyPort TruthValue
  hwifAggregatePort TruthValue
  hwifMirrorPort TruthValue
  hwifVLANType INTEGER
  hwifMcastControl INTEGER
  hwifFlowControl TruthValue
  hwifSrcMacControl TruthValue
  hwifClearStat INTEGER
  hwifXXBasePortIndex INTEGER
  hwifXXDevPortIndex INTEGER
  hwifPpsMcastControl Integer32
  hwifPpsBcastDisValControl INTEGER
  hwifUniSuppressionStep Integer32
  hwifPpsUniSuppressionMax Integer32
  hwifMulSuppressionStep Integer32
  hwifPpsMulSuppressionMax Integer32
  hwifUniSuppression Integer32
  hwifPpsUniSuppression Integer32
  hwifMulSuppression Integer32
  hwifPpsMulSuppression Integer32
  hwifComboActivePort INTEGER
  hwifBMbpsMulSuppressionMax Integer32
  hwifBMbpsMulSuppression Integer32
  hwifBKbpsMulSuppressionMax Integer32
  hwifBKbpsMulSuppressionStep Integer32
  hwifBKbpsMulSuppression Integer32
  hwifUnknownPacketDropMul DropDirection
  hwifUnknownPacketDropUni DropDirection
  hwifBMbpsUniSuppressionMax Integer32
  hwifBMbpsUniSuppression Integer32
  hwifBKbpsUniSuppressionMax Integer32
  hwifBKbpsUniSuppressionStep Integer32
  hwifBKbpsUniSuppression Integer32
  hwifOutPayloadOctets Counter64
  hwifInPayloadOctets Counter64
  hwifInErrorPktsRate Integer32
  hwifInPkts Counter64
  hwifInNormalPkts Counter64
  hwifOutPkts Counter64

HwIfAggregateEntry  
SEQUENCE    
  hwifAggregatePortIndex InterfaceIndex
  hwifAggregatePortName OCTET STRING
  hwifAggregatePortListPorts PortList
  hwifAggregateModel INTEGER
  hwifAggregateOperStatus RowStatus

HwifHybridPortEntry  
SEQUENCE    
  hwifHybridPortIndex INTEGER
  hwifHybridTaggedVlanListLow OCTET STRING
  hwifHybridTaggedVlanListHigh OCTET STRING
  hwifHybridUnTaggedVlanListLow OCTET STRING
  hwifHybridUnTaggedVlanListHigh OCTET STRING

HwifComboPortEntry  
SEQUENCE    
  hwifComboPortIndex InterfaceIndex
  hwifComboPortCurActive INTEGER

HwIfVLANTrunkStatusEntry  
SEQUENCE    
  hwifVLANTrunkIndex InterfaceIndex
  hwifVLANTrunkGvrpRegistration INTEGER
  hwifVLANTrunkPassListLow OCTET STRING
  hwifVLANTrunkPassListHigh OCTET STRING
  hwifVLANTrunkAllowListLow OCTET STRING
  hwifVLANTrunkAllowListHigh OCTET STRING

HwEthernetEntry  
SEQUENCE    
  hwifEthernetDuplex INTEGER
  hwifEthernetMTU INTEGER
  hwifEthernetSpeed INTEGER
  hwifEthernetMdi INTEGER
  hwMaxMacLearn INTEGER
  hwifMacAddressLearn INTEGER
  hwifEthernetTest INTEGER
  hwifMacAddrLearnMode INTEGER
  hwifEthernetFlowInterval INTEGER
  hwifEthernetIsolate OCTET STRING
  hwifVlanVPNStatus INTEGER
  hwifVlanVPNUplinkStatus INTEGER
  hwifVlanVPNTPID Integer32
  hwifIsolateGroupID Integer32
  hwifisUplinkPort INTEGER
  hwifEthernetAutoSpeedMask SpeedModeFlag
  hwifEthernetAutoSpeed SpeedModeFlag

HwPortIsolateGroupEntry  
SEQUENCE    
  hwPortIsolateGroupIndex Integer32
  hwPortIsolateUplinkIfIndex InterfaceIndex
  hwPortIsolateGroupRowStatus RowStatus
  hwPortIsolateGroupDescription DisplayString

Defined Values

hwLswL2InfMib 1.3.6.1.4.1.2011.2.23.1.5
Tok_String
MODULE-IDENTITY    

hwLswExtInterface 1.3.6.1.4.1.2011.2.23.1.1
OBJECT IDENTIFIER    

hwifXXTable 1.3.6.1.4.1.2011.2.23.1.1.1
Extended Huawei private interface information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfXXEntry

hwifXXEntry 1.3.6.1.4.1.2011.2.23.1.1.1.1
Entries of extended Huawei private interface information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfXXEntry  

hwifUnBoundPort 1.3.6.1.4.1.2011.2.23.1.1.1.1.1
Whether it is the unbound port. (true indicates that the port is the main port of the aggregation or the port does not participate in the aggregation.)
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwifISPhyPort 1.3.6.1.4.1.2011.2.23.1.1.1.1.2
Whether it is a physical interface.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwifAggregatePort 1.3.6.1.4.1.2011.2.23.1.1.1.1.3
Whether it is the aggregated port. (if the port participates in the aggregation, this value is true.)
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwifMirrorPort 1.3.6.1.4.1.2011.2.23.1.1.1.1.4
Whether it is a mirror port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hwifVLANType 1.3.6.1.4.1.2011.2.23.1.1.1.1.5
port vlan types. hybrid (3) port can carry multiple VLANs. If fabric function is supported, fabric(4) means the port is a fabric port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER vLANTrunk(1), access(2), hybrid(3), fabric(4)  

hwifMcastControl 1.3.6.1.4.1.2011.2.23.1.1.1.1.6
Broadcast storm suppression with the step length of 1, ranging from 1 to 100 percent. In some products the step is 5, ranging from 5 to 100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

hwifFlowControl 1.3.6.1.4.1.2011.2.23.1.1.1.1.7
Flow control status.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hwifSrcMacControl 1.3.6.1.4.1.2011.2.23.1.1.1.1.8
Whether to filter by source MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwifClearStat 1.3.6.1.4.1.2011.2.23.1.1.1.1.9
Clear all port statistics. Read operation not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(1)  

hwifXXBasePortIndex 1.3.6.1.4.1.2011.2.23.1.1.1.1.10
Index number of the port and the first port index of the device is 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

hwifXXDevPortIndex 1.3.6.1.4.1.2011.2.23.1.1.1.1.11
Device index of the port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

hwifPpsMcastControl 1.3.6.1.4.1.2011.2.23.1.1.1.1.12
The broadcast suppression with pps(packet per second) type. The max value is determined by the port type and product.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifPpsBcastDisValControl 1.3.6.1.4.1.2011.2.23.1.1.1.1.13
Control the port's pps(packet per second) broadcast suppression. When the port is enabled, its pps broadcast suppression value is the global disperse value, and when disabled, it doesn't suppress broadcast.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwifUniSuppressionStep 1.3.6.1.4.1.2011.2.23.1.1.1.1.14
The step of unicast suppression in ratio mode.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifPpsUniSuppressionMax 1.3.6.1.4.1.2011.2.23.1.1.1.1.15
The max pps(packet per second) value of unicast suppression in pps mode.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifMulSuppressionStep 1.3.6.1.4.1.2011.2.23.1.1.1.1.16
The step of multicast suppression in ratio mode.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifPpsMulSuppressionMax 1.3.6.1.4.1.2011.2.23.1.1.1.1.17
The max pps(packet per second) value of multicast suppression in pps mode.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifUniSuppression 1.3.6.1.4.1.2011.2.23.1.1.1.1.18
The unicast suppression with the ranging from 1 to 100 percent in ratio mode. The step is determined by hwifUniSuppressionStep.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifPpsUniSuppression 1.3.6.1.4.1.2011.2.23.1.1.1.1.19
The unicast suppression in pps(packet per second) mode. The max value is determined by hwifPpsUniSuppressionMax.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifMulSuppression 1.3.6.1.4.1.2011.2.23.1.1.1.1.20
The multicast suppression with ranging from 1 to 100 percent in ratio mode. The step is determined by hwifMulSuppressionStep.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifPpsMulSuppression 1.3.6.1.4.1.2011.2.23.1.1.1.1.21
The multicast suppression in pps(packet per second) mode. The max pps value is determined by hwifPpsMulSuppressionMax.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifComboActivePort 1.3.6.1.4.1.2011.2.23.1.1.1.1.22
Active port on combo interface.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER fiber(1), copper(2), na(3)  

hwifBMbpsMulSuppressionMax 1.3.6.1.4.1.2011.2.23.1.1.1.1.23
The maximum value of the multicast suppression with bandwidth-based(Mbps) that a port can be configured.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifBMbpsMulSuppression 1.3.6.1.4.1.2011.2.23.1.1.1.1.24
With bandwidth-based multicast suppression, the bandwidth is measured in Mbps. The upper limit of the multicast suppession with bandwidth-based(Mbps) is the value of hwifBMbpsMulSuppressionMax in the entry. The default value of hwifBMbpsMulSuppression is the value of hwifBMbpsMulSuppressionMax.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifBKbpsMulSuppressionMax 1.3.6.1.4.1.2011.2.23.1.1.1.1.25
The maximum value of the multicast suppression with bandwidth-based(Kbps) that a port can be configured.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifBKbpsMulSuppressionStep 1.3.6.1.4.1.2011.2.23.1.1.1.1.26
The step of multicast suppression with bandwidth-based(Kbps).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifBKbpsMulSuppression 1.3.6.1.4.1.2011.2.23.1.1.1.1.27
With bandwidth-based multicast suppression, the bandwidth is measured in Kbps. The upper limit of the multicast suppession with bandwidth-based(Kbps) is the value of hwifBKbpsMulSuppressionMax in the entry. The value of hwifBKbpsMulSuppression must be multiple of the value of hwifBKbpsMulSuppressionStep. The default value of hwifBKbpsMulSuppression is the value of hwifBKbpsMulSuppressionMax.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifUnknownPacketDropMul 1.3.6.1.4.1.2011.2.23.1.1.1.1.28
Control the port's unknown-multicast packets drop. When inbound direction is enabled on this port, the port will drop unknown-multicast packets in inbound direction. When outbound direction is enabled on this port, the port will drop unknown-multicast packets in outbound direction. When both directions are enabled on this port, the port will drop unknown-multicast packets in both inbound and outbound directions.
Status: current Access: read-write
OBJECT-TYPE    
  DropDirection  

hwifUnknownPacketDropUni 1.3.6.1.4.1.2011.2.23.1.1.1.1.29
Control the port's unknown-unicast packets drop. When inbound direction is enabled on this port, the port will drop unknown-unicast packets in inbound direction. When outbound direction is enabled on this port, the port will drop unknown-unicast packets in outbound direction. When both directions are enabled on this port, the port will drop unknown-unicast packets in both inbound and outbound directions.
Status: current Access: read-write
OBJECT-TYPE    
  DropDirection  

hwifBMbpsUniSuppressionMax 1.3.6.1.4.1.2011.2.23.1.1.1.1.30
The maximum value of the unicast suppression with bandwidth-based (Mbps) that a port can be configured.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifBMbpsUniSuppression 1.3.6.1.4.1.2011.2.23.1.1.1.1.31
With bandwidth-based Unicast suppression, the bandwidth is measured in Mbps. The upper limit of the unicast suppession with bandwidth-based(Mbps) is the value of hwifBMbpsUniSuppressionMax in the entry. The default value of hwifBMbpsUniSuppression is the value of hwifBMbpsUniSuppressionMax.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifBKbpsUniSuppressionMax 1.3.6.1.4.1.2011.2.23.1.1.1.1.32
The maximum value of the unicast suppression with bandwidth-based (Kbps) that a port can be configured.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifBKbpsUniSuppressionStep 1.3.6.1.4.1.2011.2.23.1.1.1.1.33
The step of unicast suppression with bandwidth-based(Kbps).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifBKbpsUniSuppression 1.3.6.1.4.1.2011.2.23.1.1.1.1.34
With bandwidth-based unicast suppression, the bandwidth is measured in Kbps. The upper limit of the unicast suppession with bandwidth-based(Kbps) is the value of hwifBKbpsUniSuppressionMax in the entry. The value of hwifBKbpsUniSuppression must be multiple of the value of hwifBKbpsUniSuppressionStep. The default value of hwifBKbpsUniSuppression is the value of hwifBKbpsUniSuppressionMax.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifOutPayloadOctets 1.3.6.1.4.1.2011.2.23.1.1.1.1.35
The actual output octets of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwifInPayloadOctets 1.3.6.1.4.1.2011.2.23.1.1.1.1.36
The actual input octets of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwifInErrorPktsRate 1.3.6.1.4.1.2011.2.23.1.1.1.1.37
The rate of inbound error packets on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwifInPkts 1.3.6.1.4.1.2011.2.23.1.1.1.1.38
The number of packets received on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwifInNormalPkts 1.3.6.1.4.1.2011.2.23.1.1.1.1.39
The number of normal packets received on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwifOutPkts 1.3.6.1.4.1.2011.2.23.1.1.1.1.40
The number of packets sent on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwifAggregateTable 1.3.6.1.4.1.2011.2.23.1.1.2
Port aggregation information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfAggregateEntry

hwifAggregateEntry 1.3.6.1.4.1.2011.2.23.1.1.2.1
Port aggregation information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfAggregateEntry  

hwifAggregatePortIndex 1.3.6.1.4.1.2011.2.23.1.1.2.1.1
Index number of the main aggregated port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

hwifAggregatePortName 1.3.6.1.4.1.2011.2.23.1.1.2.1.2
Aggregation group name.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

hwifAggregatePortListPorts 1.3.6.1.4.1.2011.2.23.1.1.2.1.3
Portlist of a aggregating.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

hwifAggregateModel 1.3.6.1.4.1.2011.2.23.1.1.2.1.4
Load sharing mode for the port aggregation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ingress(1), both(2), round-robin(3)  

hwifAggregateOperStatus 1.3.6.1.4.1.2011.2.23.1.1.2.1.5
Current operation status of the row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwifHybridPortTable 1.3.6.1.4.1.2011.2.23.1.1.3
Hybrid-port configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwifHybridPortEntry

hwifHybridPortEntry 1.3.6.1.4.1.2011.2.23.1.1.3.1
Hybrid-port configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwifHybridPortEntry  

hwifHybridPortIndex 1.3.6.1.4.1.2011.2.23.1.1.3.1.1
Index number of Hybrid-port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

hwifHybridTaggedVlanListLow 1.3.6.1.4.1.2011.2.23.1.1.3.1.2
Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each tagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is tagged in the set of VLANs; the VLAN is not tagged if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

hwifHybridTaggedVlanListHigh 1.3.6.1.4.1.2011.2.23.1.1.3.1.3
Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each tagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is tagged in the set of VLANs; the VLAN is not tagged if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

hwifHybridUnTaggedVlanListLow 1.3.6.1.4.1.2011.2.23.1.1.3.1.4
Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

hwifHybridUnTaggedVlanListHigh 1.3.6.1.4.1.2011.2.23.1.1.3.1.5
Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

hwifComboPortTable 1.3.6.1.4.1.2011.2.23.1.1.4
Combo-port table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwifComboPortEntry

hwifComboPortEntry 1.3.6.1.4.1.2011.2.23.1.1.4.1
The entry of hwifComboPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwifComboPortEntry  

hwifComboPortIndex 1.3.6.1.4.1.2011.2.23.1.1.4.1.1
The combo-port interface index. Its value is the same as the value of ifIndex in ifTable, but only includes indexes of the combo-port interfaces.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

hwifComboPortCurActive 1.3.6.1.4.1.2011.2.23.1.1.4.1.2
Current active interface of combo interfaces. The value 'fiber' means the interface with fiber connector of the pair of combo-port interfaces is active. The value 'copper' means the interface with copper connector of the pair is active. The value 'na' means not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fiber(1), copper(2), na(3)  

hwLswL2InfMibObject 1.3.6.1.4.1.2011.2.23.1.5.1
OBJECT IDENTIFIER    

hwSlotPortMax 1.3.6.1.4.1.2011.2.23.1.5.1.1
Max ports of the slots.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

hwSwitchPortMax 1.3.6.1.4.1.2011.2.23.1.5.1.2
Max ports that this switch includes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

hwifVLANTrunkStatusTable 1.3.6.1.4.1.2011.2.23.1.5.1.3
Gvrp attributes on the VlanTrunk port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfVLANTrunkStatusEntry

hwifVLANTrunkStatusEntry 1.3.6.1.4.1.2011.2.23.1.5.1.3.1
Gvrp attributes on the VlanTrunk port.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfVLANTrunkStatusEntry  

hwifVLANTrunkIndex 1.3.6.1.4.1.2011.2.23.1.5.1.3.1.1
Index number of the VLANTrunk interface.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

hwifVLANTrunkGvrpRegistration 1.3.6.1.4.1.2011.2.23.1.5.1.3.1.2
GVRP registration information normal: This is the default configuration. Allow create, register and unregister vlans dynamiclly at this port. fixed: Aallow create and register vlan manually at this port. Prevent from unregistering vlans or registering known vlans of this port at another trunk port. forbidden: Unregister all vlans but vlan 1, forbid to create or register any other vlans at this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), fixed(2), forbidden(3)  

hwifVLANTrunkPassListLow 1.3.6.1.4.1.2011.2.23.1.5.1.3.1.4
Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each actually passed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is actually passed in the set of VLANs; the VLAN is not actually passed if its bit has a value of '0'.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwifVLANTrunkPassListHigh 1.3.6.1.4.1.2011.2.23.1.5.1.3.1.5
Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each actually passed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is actually passed in the set of VLANs; the VLAN is not actually passed if its bit has a value of '0'.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwifVLANTrunkAllowListLow 1.3.6.1.4.1.2011.2.23.1.5.1.3.1.6
Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is allowed in the set of VLANs; the VLAN is not allowed if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwifVLANTrunkAllowListHigh 1.3.6.1.4.1.2011.2.23.1.5.1.3.1.7
Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is allowed in the set of VLANs; the VLAN is not allowed if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwethernetTable 1.3.6.1.4.1.2011.2.23.1.5.1.4
Ethernet port attribute table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwEthernetEntry

hwethernetEntry 1.3.6.1.4.1.2011.2.23.1.5.1.4.1
Entries of Ethernet port attribute table
Status: current Access: not-accessible
OBJECT-TYPE    
  HwEthernetEntry  

hwifEthernetDuplex 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.3
Ethernet interface mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER full(1), half(2), auto(3)  

hwifEthernetMTU 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.4
MTU on the Ethernet interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwifEthernetSpeed 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.5
Ethernet interface speed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(0), s10M(10), s100M(100), s1000M(1000), s10000M(10000), s24000M(24000), s40000M(40000), s100000M(100000)  

hwifEthernetMdi 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.7
Type of the line connected to the port. MDI-II (straight-through cable): 1 MDI-X (crossover cable): 2 MDI-AUTO (auto-sensing): 3
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mdi-ii(1), mdi-x(2), mdi-auto(3)  

hwMaxMacLearn 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.8
The maximum number of MAC addresses that the port can learn. The value -1 means that the number of Mac addresses that the port can learn is unlimited.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -1..2147483647  

hwifMacAddressLearn 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.9
This object indicates if the interface is allowed to learn mac address. eanbled(1) means the interface can learn mac address, otherwise disabled(2) can be set.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hwifEthernetTest 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.10
Test this interface. The actual testing will be different according to products. Read operation not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER test(1)  

hwifMacAddrLearnMode 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.11
Status indicates mac address learn mode of the interface. IVL(1) means independent VLAN learning. SVL means shared VLAN learning.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER iVL(1), sVL(2)  

hwifEthernetFlowInterval 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.12
Set flow interval of the ethernet. The NMS should set value to integer which is a multiple of 5.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..300  

hwifEthernetIsolate 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.13
Isolate group means that all ports in the same isolate group can not send and receive packets each other. Each octet within this value specifies a set of eight isolate groups, with the first octet specifying isolate groups 1 through 8, the second octet specifying isolate groups 9 through 16, etc. Within each octet, the leftmost bit is the first bit. the first bit represents the lowest numbered isolate group, and the last bit represents the highest numbered isolate group. one port can belong to more than one isolate group. Thus, each isolate group is represented by a single bit within the value of this object. If that bit has a value of '1', then that isolate group includes this port; the port is not included if its bit has a value of '0'. for example, the first octet is '10000100' means that the port is included in the isolate group 1 and isolate group 6.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwifVlanVPNStatus 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.14
Vlan VPN enable status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hwifVlanVPNUplinkStatus 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.15
Vlan VPN uplink status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hwifVlanVPNTPID 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.16
Port based Vlan VPN TPID(Tag Protocol Indentifier), default value is 0x8100. Please refer to hwVlanVPNTPIDMode to get more information.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwifIsolateGroupID 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.17
Isolate group identifier. Value zero means this interface does not belong to any isolate group.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwifisUplinkPort 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.18
Ethernet uplink status, default value is 2.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

hwifEthernetAutoSpeedMask 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.19
This object specifies which kinds of speed mode can be negotiated. Each bit corresponds to a kind of speed mode. If the value of a bit is '1', it means the corresponding speed mode is negotiable on the port. Otherwise the negotiation for that kind of speed mode is not supported on this port. If there are several negotiable speed modes, all bits for them are '1'. For example, if the speed mode 's10M' and 's1000M' can be negotiable, the value of this object is 0xA0.
Status: current Access: read-only
OBJECT-TYPE    
  SpeedModeFlag  

hwifEthernetAutoSpeed 1.3.6.1.4.1.2011.2.23.1.5.1.4.1.20
This object indicates which kinds of speed mode are negotiable on this port. Only when a bit of hwifEthernetAutoSpeedMask is '1', the corresponding bit of this object can be set to '1', indicating the corresponding speed mode is negotiable. For example, if the value of hwifEthernetAutoSpeedMask is 0xA0, which indicates speed mode 's10M' and 's1000M' are negotiable, the possible value of this object should be one of the four values (0x00, 0x20, 0x80 and 0xA0). If the value of hwifEthernetSpeed is not 'auto', the value of this object is insignificant and should be ignored. The value length of this object should be as long as that of hwifEthernetAutoSpeedMask.
Status: current Access: read-write
OBJECT-TYPE    
  SpeedModeFlag  

hwIsolateGroupMax 1.3.6.1.4.1.2011.2.23.1.5.1.5
Max isolate group that this device support, the value is zero means that the device does not support isolate group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwGlobalBroadcastMaxPps 1.3.6.1.4.1.2011.2.23.1.5.1.6
The global max packets per second. When it is set, the value of BroadcastMaxPps in all ports will be changed to that setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..14881000  

hwGlobalBroadcastMaxRatio 1.3.6.1.4.1.2011.2.23.1.5.1.7
The global max-ratio of broadcast from 0 to 100 percent. When it is set, the value of BroadcastMaxRatio in all ports will be changed to that setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

hwBpduTunnelStatus 1.3.6.1.4.1.2011.2.23.1.5.1.8
Bpdu tunnel enable status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hwVlanVPNTPIDMode 1.3.6.1.4.1.2011.2.23.1.5.1.9
Vlan VPN TPID mode. The value 'port-based' means VLAN VPN TPID value would be set based on port via hwifVlanVPNTPID. In this situation, hwVlanVPNTPID is meaningless and always return 0x8100. The value 'global' means VLAN VPN TPID value should be set globally via hwVlanVPNTPID. In this situation, hwifVlanVPNTPID in hwethernetTable has the same value with hwVlanVPNTPID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER port-based(1), global(2)  

hwVlanVPNTPID 1.3.6.1.4.1.2011.2.23.1.5.1.10
Global Vlan VPN TPID(Tag Protocol Indentifier), default value is 0x8100.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwPortIsolateGroupTable 1.3.6.1.4.1.2011.2.23.1.5.1.11
Isolate Group attribute table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortIsolateGroupEntry

hwPortIsolateGroupEntry 1.3.6.1.4.1.2011.2.23.1.5.1.11.1
The entry of hwPortIsolateGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwPortIsolateGroupEntry  

hwPortIsolateGroupIndex 1.3.6.1.4.1.2011.2.23.1.5.1.11.1.1
Port isolate group identifier. The index of the hwPortIsolateGroupTable. The value ranges from 1 to the limit of isolate group quantity.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hwPortIsolateUplinkIfIndex 1.3.6.1.4.1.2011.2.23.1.5.1.11.1.2
Index number of the uplink interface.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

hwPortIsolateGroupRowStatus 1.3.6.1.4.1.2011.2.23.1.5.1.11.1.3
Current operation status of the row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwPortIsolateGroupDescription 1.3.6.1.4.1.2011.2.23.1.5.1.11.1.4
Port isolate group description, default value is zero-length string.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..80)  

hwMaxMacLearnRange 1.3.6.1.4.1.2011.2.23.1.5.1.12
The maximum number of MAC address that the port supports.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32