HUAWEI-LI-MIB

File: HUAWEI-LI-MIB.mib (31429 bytes)

Imported modules

HUAWEI-MIB INET-ADDRESS-MIB SNMPv2-CONF
SNMPv2-SMI SNMPv2-TC

Imported symbols

hwDatacomm InetAddress InetPortNumber
InetAddressType InetAddressPrefixLength OBJECT-GROUP
MODULE-COMPLIANCE NOTIFICATION-GROUP Integer32
Unsigned32 OBJECT-TYPE MODULE-IDENTITY
NOTIFICATION-TYPE DateAndTime MacAddress
RowStatus TEXTUAL-CONVENTION

Defined Types

HWLiDscp  
An integer that is in the range of the DiffServ codepoint values.
TEXTUAL-CONVENTION    
  Integer32 0..63  

HwLiGatewayEntry  
SEQUENCE    
  hwLiGatewayIndex Integer32
  hwLiGatewayAddressType InetAddressType
  hwLiGatewayX2Protocol INTEGER
  hwLiGatewayX2Address InetAddress
  hwLiGatewayX2Port InetPortNumber
  hwLiGatewayX3Protocol INTEGER
  hwLiGatewayX3Address InetAddress
  hwLiGatewayX3Port InetPortNumber
  hwLiGatewayX3HeartBeatTimer Integer32
  hwLiGatewayX3NoResponseNum Integer32
  hwLiGatewayX3OperateStatus INTEGER
  hwLiGatewayX3Dscp HWLiDscp
  hwLiGatewayRowStatus RowStatus
  hwLiGatewayX3AddressType InetAddressType
  hwLiGatewayX2AddressType InetAddressType

HwLiStreamEntry  
SEQUENCE    
  hwLiStreamIndex Integer32
  hwLiStreamLiId Unsigned32
  hwLiStreamActivationType INTEGER
  hwLiStreamSessionId Integer32
  hwLiStreamTargetIdType INTEGER
  hwLiStreamSrcMacAddress MacAddress
  hwLiStreamDstMacAddress MacAddress
  hwLiStreamSrcIpAddress InetAddress
  hwLiStreamSrcIpLength InetAddressPrefixLength
  hwLiStreamDstIpAddress InetAddress
  hwLiStreamDstIpLength InetAddressPrefixLength
  hwLiStreamProtocol Integer32
  hwLiStreamSrcPort InetPortNumber
  hwLiStreamDstPort InetPortNumber
  hwLiStreamIfIndex Integer32
  hwLiStreamUserName OCTET STRING
  hwLiStreamRowStatus RowStatus
  hwLiStreamSrcIpAddressType InetAddressType
  hwLiStreamDstIpAddressType InetAddressType
  hwLiStreamSrcVpnName OCTET STRING
  hwLiStreamDstVpnName OCTET STRING
  hwLiStreamL2tpIfIndex Integer32
  hwLiStreamL2tpVlanId Integer32
  hwLiStreamAcctSessionId OCTET STRING

Defined Values

hwLiMib 1.3.6.1.4.1.2011.5.25.131
This module manages huawei's Lawful interception feature.
MODULE-IDENTITY    

hwLiMibNotifs 1.3.6.1.4.1.2011.5.25.131.1
OBJECT IDENTIFIER    

hwLiMibActive 1.3.6.1.4.1.2011.5.25.131.1.1
This notification is sent when an intercepting router or switch is first capable of intercepting a packet corresponding to a configured data stream.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLiX3HeartBeatAlarm 1.3.6.1.4.1.2011.5.25.131.1.2
This notification is sent when an LIG is lost connection to the device which intercepting packet corresponding to a configured data stream.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLiX3HeartBeatRecover 1.3.6.1.4.1.2011.5.25.131.1.3
This notification is sent when an LIG is recover connection to the device which intercepting packet corresponding to a configured data stream.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLiMibObjects 1.3.6.1.4.1.2011.5.25.131.2
OBJECT IDENTIFIER    

hwLiAgentObjects 1.3.6.1.4.1.2011.5.25.131.2.1
OBJECT IDENTIFIER    

hwLiAgentTime 1.3.6.1.4.1.2011.5.25.131.2.1.1
The time of the LI agent.Read-only.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

hwLiAgentEnable 1.3.6.1.4.1.2011.5.25.131.2.1.2
The status of the LI agent.Read-only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hwLiAgentX2IpAddress 1.3.6.1.4.1.2011.5.25.131.2.1.3
The IP address of the X2 interface in LI agent.Just can be read by server and can be set in command line.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

hwLiAgentX2Port 1.3.6.1.4.1.2011.5.25.131.2.1.4
The Port of the X2 interface in LI agent.Just can be read by server and can be set in command line.
Status: current Access: read-only
OBJECT-TYPE    
  InetPortNumber  

hwLiAgentX3IpAddress 1.3.6.1.4.1.2011.5.25.131.2.1.5
The IP address of the X3 interface in LI agent.Just can be read by server and can be set in command line.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

hwLiAgentX3Port 1.3.6.1.4.1.2011.5.25.131.2.1.6
The Port of the X3 interface in LI agent.Just can be read by server and can be set in command line.
Status: current Access: read-only
OBJECT-TYPE    
  InetPortNumber  

hwLiGatewayGroup 1.3.6.1.4.1.2011.5.25.131.2.3
OBJECT IDENTIFIER    

hwLiGatewayNewIndex 1.3.6.1.4.1.2011.5.25.131.2.3.1
This object contains a value which may be used as an index value for a new HwLiGatewayEntry. This is to reduce the probability of errors during creation of new hwLiGatewayTable entries.0 means no free resource.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 1..10  

hwLiGatewayTable 1.3.6.1.4.1.2011.5.25.131.2.3.2
This table lists the LI Gateway Devices with which the intercepting device communicates. This table is written by the LI Gateway Device, and is always volatile. This is because intercepts may disappear during a restart of the intercepting equipment. Entries are added to this table via hwLiGatewayStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLiGatewayEntry

hwLiGatewayEntry 1.3.6.1.4.1.2011.5.25.131.2.3.2.1
The entry describes a single session maintained with an application on a LI Gateway Device.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLiGatewayEntry  

hwLiGatewayIndex 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.1
The index of the LIG itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..10  

hwLiGatewayAddressType 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.2
The type of address in LIG
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwLiGatewayX2Protocol 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.3
The protocol used in transferring intercepted data to the Gateway Device.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER udp(1), tcp(2)  

hwLiGatewayX2Address 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.4
The IP Address of the Gateway Device's network interface to which to direct IRI.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

hwLiGatewayX2Port 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.5
The port number on the Gateway Device's network interface to which to direct IRI.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

hwLiGatewayX3Protocol 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.6
The protocol used in transferring intercepted data to the Gateway Device.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER udp(1), tcp(2)  

hwLiGatewayX3Address 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.7
The IP Address of the Gateway Device's network interface to which to direct CC.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

hwLiGatewayX3Port 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.8
The port number on the Gateway Device's network interface to which to direct intercepted traffic.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

hwLiGatewayX3HeartBeatTimer 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.9
The timer for sending HeartBeat to LIG,In seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hwLiGatewayX3NoResponseNum 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.10
The times of heartbeats that allowed to missed from LIG
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 2..16  

hwLiGatewayX3OperateStatus 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.11
The operate status of X3 interface
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), noHeartBeat(2), linkdown(3)  

hwLiGatewayX3Dscp 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.12
The Differentiated Services Code Point the intercepting device applies to the IP packets encapsulating the intercepted traffic.
Status: current Access: read-create
OBJECT-TYPE    
  HWLiDscp  

hwLiGatewayRowStatus 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.14
The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLiGatewayX3AddressType 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.15
The type of address in LIG
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwLiGatewayX2AddressType 1.3.6.1.4.1.2011.5.25.131.2.3.2.1.16
The type of address in LIG
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwLiGatewayCapabilities 1.3.6.1.4.1.2011.5.25.131.2.3.3
This object displays the device capabilities with respect to certain fields in Gateway Device table. This may be dependent on hardware capabilities, software capabilities. The following values may be supported: ipv4SrcInterface: SNMP ifIndex Value may be used to select the interface (denoted by hwLiGatewaySrcInterface) on the intercepting device from which to transmit intercepted data to an IPv4 address Gateway Device. ipv6SrcInterface: SNMP ifIndex Value may be used to select the interface (denoted by hwLiGatewaySrcInterface) on the intercepting device from which to transmit intercepted data to an IPv6 address Gateway Device. udp: UDP may be used as transport protocol (denoted by hwLiGatewayTransport) in transferring intercepted data to the Gateway Device. tcp: TCP may be used as transport protocol (denoted by hwLiGatewayTransport) in transferring intercepted data to the Gateway Device.
Status: current Access: read-only
OBJECT-TYPE    
  BITS ipv4SrcInterface(0), ipv6SrcInterface(1), udp(2), tcp(3)  

hwLiStreamGroup 1.3.6.1.4.1.2011.5.25.131.2.4
OBJECT IDENTIFIER    

hwLiStreamTable 1.3.6.1.4.1.2011.5.25.131.2.4.2
The Intercept Stream Table lists the IPv4 and IPv6 streams to be intercepted. The same data stream must be used by one LIG. The first index indicates which LIG the intercepted traffic will be diverted to. The second index permits multiple classifiers to be used together, such as having an IP address as source or destination.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLiStreamEntry

hwLiStreamEntry 1.3.6.1.4.1.2011.5.25.131.2.4.2.1
A stream entry indicates a single data stream to be intercepted to a Mediation Device. Many selected data streams may go to the same application interface, and many application interfaces are supported.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLiStreamEntry  

hwLiStreamIndex 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.1
The index of the stream itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..8192  

hwLiStreamLiId 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.2
The ID indicate a independency stream in a LIG .
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwLiStreamActivationType 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.3
Intercepted IRI or CC or BOTH.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER iri(1), cc(2), both(3)  

hwLiStreamSessionId 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.4
The index of the stream itself.0 means no session ID will be specified
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

hwLiStreamTargetIdType 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.5
Target ID type specifies the type of packets. 1 means one direction traffic is intercept, 2 means bidirectional traffic is intercept. for bidirectional interception, if the source IP or destination IP in a packet is equal with the configured hwLiStreamSrcIpAddress If other condition is satisfied then the packet is intercepted. for one-directional interception, if the sourceIP and DestinationIP in a packet is equal with the configured hwLiStreamSrcIpAddress and hwLiStreamDstIPAddress If other condition is satisfied then the packet is intercepted
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER oneDirection(1), biDirection(2)  

hwLiStreamSrcMacAddress 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.7
Source Mac address of the packets which will be intercepted.0000-0000-0000 means no MAC address will be specified
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

hwLiStreamDstMacAddress 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.8
Destination Mac address of the packets which will be intercepted.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

hwLiStreamSrcIpAddress 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.9
The Source Address used in packet selection. This address will be of the type specified in hwLiStreamIpAddrType.0.0.0.0 means no IP address will be specified
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

hwLiStreamSrcIpLength 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.10
The length of the Source Prefix. A value of 32 causes all addresses to match. This prefix length will be consistent with the type specified in hwLiStreamIpAddrType.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressPrefixLength  

hwLiStreamDstIpAddress 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.11
The Destination address or prefix used in packet selection. This address will be of the type specified in hwLiStreamIpAddrType.0.0.0.0 means no IP address will be specified
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

hwLiStreamDstIpLength 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.12
The length of the Destination Prefix. A value of 32 causes all addresses to match. This prefix length will be consistent with the type specified in hwLiStreamIpAddrType.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressPrefixLength  

hwLiStreamProtocol 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.13
Protocol type of the packets which will be intercepted.0 means no Protocol type will be specified
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hwLiStreamSrcPort 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.14
The fourth layer source port.0 means no Port will be specified
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

hwLiStreamDstPort 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.15
The fourth layer Destination port.0 means no Port will be specified
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

hwLiStreamIfIndex 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.16
The interface switch carrying the intercepted taffic.0 means no interface will be specified
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

hwLiStreamUserName 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.17
The username whose traffic will be intercepted.zero-length means no user will be specified
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLiStreamRowStatus 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.18
The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLiStreamSrcIpAddressType 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.19
The source IP address of the interception stream
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwLiStreamDstIpAddressType 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.20
The destination IP address of the interception stream
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwLiStreamSrcVpnName 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.21
The source VPN instance name whose traffic will be intercepted.zero-length means no VPN will be specified
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLiStreamDstVpnName 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.22
The destination VPN instance name whose traffic will be intercepted. zero-length means no VPN will be specified
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLiStreamL2tpIfIndex 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.23
The L2TP ifindex of intercepting stream.0 means no l2tpIfindex will be specified
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

hwLiStreamL2tpVlanId 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.24
The L2TP VLAN ID of intercepting stream.0 means no Vlan will be specified
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

hwLiStreamAcctSessionId 1.3.6.1.4.1.2011.5.25.131.2.4.2.1.25
The accounting session ID of intercepting stream.zero-length means no accouting session ID will be specified
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLiMibConform 1.3.6.1.4.1.2011.5.25.131.3
OBJECT IDENTIFIER    

hwLiMibCompliances 1.3.6.1.4.1.2011.5.25.131.3.2
OBJECT IDENTIFIER    

hwLiMibCompliance 1.3.6.1.4.1.2011.5.25.131.3.2.1
Description.
Status: current Access: read-create
MODULE-COMPLIANCE    

hwLiMibGroups 1.3.6.1.4.1.2011.5.25.131.3.3
OBJECT IDENTIFIER    

hwLiAgentComplianceGroup 1.3.6.1.4.1.2011.5.25.131.3.3.1
Description.
Status: current Access: read-create
OBJECT-GROUP    

hwLiGatewayComplianceGroup 1.3.6.1.4.1.2011.5.25.131.3.3.2
Description.
Status: current Access: read-create
OBJECT-GROUP    

hwLiStreamComplianceGroup 1.3.6.1.4.1.2011.5.25.131.3.3.3
Description.
Status: current Access: read-create
OBJECT-GROUP    

hwLiNotificationGroup 1.3.6.1.4.1.2011.5.25.131.3.3.4
Description.
Status: current Access: read-create
NOTIFICATION-GROUP    

hwLiGatewayCpbComplianceGroup 1.3.6.1.4.1.2011.5.25.131.3.3.5
Description.
Status: current Access: read-create
OBJECT-GROUP