HUAWEI-ENTITY-EXTENT-MIB

File: HUAWEI-ENTITY-EXTENT-MIB.mib (164477 bytes)

Imported modules

ENTITY-MIB HUAWEI-MIB IF-MIB
P-BRIDGE-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF
SNMPv2-SMI SNMPv2-TC

Imported symbols

entPhysicalIndex entPhysicalVendorType entPhysicalName
PhysicalClass PhysicalIndex hwDatacomm
InterfaceIndex EnabledStatus SnmpAdminString
OBJECT-GROUP MODULE-COMPLIANCE NOTIFICATION-GROUP
Integer32 Unsigned32 Counter64
OBJECT-TYPE MODULE-IDENTITY NOTIFICATION-TYPE
DateAndTime DisplayString RowStatus
TEXTUAL-CONVENTION AutonomousType

Defined Types

HwAdminState  
Represents the various possible administrative states. A value of locked means the resource is administratively prohibited from use. A value of shuttingDown means that usage is administratively limited to current instances of use. A value of unlocked means the resource is not administratively prohibited from use. A value of up means that the port is not administratively shut down and a value of down is the oppsite. A value of loopback here means the port is working in the loopback local mode. When a port is both shut down and looped back, we user the vale of down.
TEXTUAL-CONVENTION    
  INTEGER notSupported(1), locked(2), shuttingDown(3), unlocked(4), up(11), down(12), loopback(13)  

HwOperState  
Represents the possible values of operational states. A value of disabled means the resource is totally inoperable. A value of enabled means the resource is partially or fully operable. The values up(11),down(12) and connect(13) is used only for NE5000E BTB or it's extended system. A value of protocolUp means the port is available in the protocol lay or has already prepared for transmitting or receiving data. A value of linkUp means the port is only available in the physical lay. A value of linkDown means the port is not available physically.
TEXTUAL-CONVENTION    
  INTEGER notSupported(1), disabled(2), enabled(3), offline(4), up(11), down(12), connect(13), protocolUp(15), linkUp(16), linkDown(17)  

HwStandbyStatus  
Represents the possible values of standby status. A value of hotStandby means the resource is not providing service, but is will be immediately able to take over the role of the resource to be backed-up, without the need for initialization activity, and will contain the same information as the resource to be backed up. A value of coldStandy means that the resource is to back-up another resource, but will not be immediately able to take over the role of a resource to be backed up, and will require some initialization activity. A value of providingService means the resource is providing service.
TEXTUAL-CONVENTION    
  INTEGER notSupported(1), hotStandby(2), coldStandby(3), providingService(4)  

HwAlarmStatus  
Represents the possible values of alarm status. When no bits of this attribute are set, then none of the status conditions described below are present. When the value of under repair is set, the resource is currently being repaired. When the value of critical is set, one or more critical alarms are active against the resource. When the value of major is set, one or more major alarms are active against the resource. When the value of minor is set, one or more minor alarms are active against the resource. When the value of warning is set, one or more warning alarms are active against the resource. When the value of indeterminate is set, one or more alarms of indeterminate severity are active against the resource. When the value of alarm outstanding is set, one or more alarms is active against the resource. The fault may or may not be disabling.
TEXTUAL-CONVENTION    
  BITS notSupported(0), underRepair(1), critical(2), major(3), minor(4), alarmOutstanding(5), warning(6), indeterminate(7)  

HWLevelState  
The normal state of input line .
TEXTUAL-CONVENTION    
  INTEGER lowLevel(1), highLevel(2)  

HwEntityStateEntry  
SEQUENCE    
  hwEntityAdminStatus HwAdminState
  hwEntityOperStatus HwOperState
  hwEntityStandbyStatus HwStandbyStatus
  hwEntityAlarmLight HwAlarmStatus
  hwEntityCpuUsage Integer32
  hwEntityCpuUsageThreshold Integer32
  hwEntityMemUsage Integer32
  hwEntityMemUsageThreshold Integer32
  hwEntityMemSize Integer32
  hwEntityUpTime Integer32
  hwEntityTemperature Integer32
  hwEntityTemperatureThreshold Integer32
  hwEntityVoltage Integer32
  hwEntityVoltageLowThreshold Integer32
  hwEntityVoltageHighThreshold Integer32
  hwEntityTemperatureLowThreshold Integer32
  hwEntityOpticalPower Integer32
  hwEntityCurrent Integer32
  hwEntityMemSizeMega Integer32
  hwEntityPortType INTEGER
  hwEntityDuplex INTEGER
  hwEntityOpticalPowerRx Integer32
  hwEntityCpuUsageLowThreshold Integer32
  hwEntityBoardPower Integer32
  hwEntityCpuFrequency Integer32
  hwEntitySupportFlexCard INTEGER
  hwEntityBoardClass INTEGER
  hwNseOpmStatus Integer32
  hwEntityCpuMaxUsage Integer32
  hwEntityCPUType SnmpAdminString
  hwEntityMemoryType SnmpAdminString
  hwEntityFlashSize Integer32
  hwEntityIfUpTimes Integer32
  hwEntityIfDownTimes Integer32
  hwEntityCPUAvgUsage Integer32
  hwEntityMemoryAvgUsage Integer32
  hwEntityMemUsed Unsigned32
  hwEntityTotalFanNum Integer32
  hwEntityNomalFanNum Integer32
  hwEntityTotalPwrNum Integer32
  hwEntityNomalPwrNum Integer32
  hwEntityFaultLight INTEGER
  hwEntityBoardName OCTET STRING
  hwEntityBoardDescription OCTET STRING
  hwEntity5MinCpuUsage Integer32
  hwEntityStartMode INTEGER
  hwEntitySplitAttribute OCTET STRING
  hwEntityFaultLightKeepTime Integer32

HwRUModuleInfoEntry  
SEQUENCE    
  hwEntityBomId SnmpAdminString
  hwEntityBomEnDesc SnmpAdminString
  hwEntityBomLocalDesc SnmpAdminString
  hwEntityManufacturedDate DateAndTime
  hwEntityManufactureCode Integer32
  hwEntityCLEICode SnmpAdminString
  hwEntityUpdateLog SnmpAdminString
  hwEntityArchivesInfoVersion SnmpAdminString
  hwEntityOpenBomId SnmpAdminString
  hwEntityIssueNum SnmpAdminString
  hwEntityBoardType SnmpAdminString

HwOpticalModuleInfoEntry  
SEQUENCE    
  hwEntityOpticalMode INTEGER
  hwEntityOpticalWaveLength Integer32
  hwEntityOpticalTransDistance Integer32
  hwEntityOpticalVendorSn SnmpAdminString
  hwEntityOpticalTemperature Integer32
  hwEntityOpticalVoltage Integer32
  hwEntityOpticalBiasCurrent Integer32
  hwEntityOpticalRxPower Integer32
  hwEntityOpticalTxPower Integer32
  hwEntityOpticalType INTEGER
  hwEntityOpticalTransBW Integer32
  hwEntityOpticalFiberType INTEGER
  hwEntityOpticalRxLowThreshold Integer32
  hwEntityOpticalRxHighThreshold Integer32
  hwEntityOpticalTxLowThreshold Integer32
  hwEntityOpticalTxHighThreshold Integer32
  hwEntityOpticalPlug INTEGER
  hwEntityOpticalDirectionType INTEGER
  hwEntityOpticalUserEeprom DisplayString
  hwEntityOpticalRxLowWarnThreshold Integer32
  hwEntityOpticalRxHighWarnThreshold Integer32
  hwEntityOpticalTxLowWarnThreshold Integer32
  hwEntityOpticalTxHighWarnThreshold Integer32
  hwEntityOpticalVenderName DisplayString
  hwEntityOpticalVenderPn DisplayString
  hwEntityOpticalAuthenticationStatus INTEGER
  hwEntityOpticalTunableType INTEGER
  hwEntityOpticalWaveLengthDecimal Integer32
  hwEntityOpticalTunableModuleChannel Integer32
  hwEntityOpticalWaveBand INTEGER
  hwEntityOpticalLaneBiasCurrent SnmpAdminString
  hwEntityOpticalLaneRxPower SnmpAdminString
  hwEntityOpticalLaneTxPower SnmpAdminString
  hwEntityOpticalVendorOUI DisplayString
  hwEntityOpticalVendorRev DisplayString
  hwEntityOpticalGponSN DisplayString

HwMonitorInputEntry  
SEQUENCE    
  hwMonitorInputIndex Integer32
  hwMonitorInputName DisplayString
  hwMonitorInputState HWLevelState
  hwMonitorInputStateEnable EnabledStatus
  hwMonitorInputRowStatus RowStatus

HwMonitorOutputEntry  
SEQUENCE    
  hwMonitorOutputIndex Integer32
  hwMonitorOutputRuleIndex Integer32
  hwMonitorOutputMask DisplayString
  hwMonitorOutputKey DisplayString
  hwMonitorOutputRowStatus RowStatus

HwEntPowerUsedInfoEntry  
SEQUENCE    
  hwEntPowerUsedInfoBoardName OCTET STRING
  hwEntPowerUsedInfoBoardType OCTET STRING
  hwEntPowerUsedInfoBoardSlot Integer32
  hwEntPowerUsedInfoPower Integer32

HwVirtualCableTestEntry  
SEQUENCE    
  hwVirtualCableTestIfIndex InterfaceIndex
  hwVirtualCableTestPairStatus INTEGER
  hwVirtualCableTestPairLength Integer32
  hwVirtualCableTestOperation INTEGER
  hwVirtualCableTestLastTime Integer32
  hwVirtualCableTestPairAStatus INTEGER
  hwVirtualCableTestPairBStatus INTEGER
  hwVirtualCableTestPairCStatus INTEGER
  hwVirtualCableTestPairDStatus INTEGER
  hwVirtualCableTestPairALength Integer32
  hwVirtualCableTestPairBLength Integer32
  hwVirtualCableTestPairCLength Integer32
  hwVirtualCableTestPairDLength Integer32

HwTemperatureThresholdEntry  
SEQUENCE    
  hwEntityTempSlotId Integer32
  hwEntityTempI2CId Integer32
  hwEntityTempAddr Integer32
  hwEntityTempChannel Integer32
  hwEntityTempStatus INTEGER
  hwEntityTempValue Integer32
  hwEntityTempMinorAlmThreshold Integer32
  hwEntityTempMajorAlmThreshold Integer32
  hwEntityTempFatalAlmThreshold Integer32

HwVoltageInfoEntry  
SEQUENCE    
  hwEntityVolSlot Integer32
  hwEntityVolI2CId Integer32
  hwEntityVolAddr Integer32
  hwEntityVolChannel Integer32
  hwEntityVolStatus INTEGER
  hwEntityVolRequired Integer32
  hwEntityVolCurValue Integer32
  hwEntityVolRatio Integer32
  hwEntityVolLowAlmMajor Integer32
  hwEntityVolLowAlmFatal Integer32
  hwEntityVolHighAlmMajor Integer32
  hwEntityVolHighAlmFatal Integer32

HwFanStatusEntry  
SEQUENCE    
  hwEntityFanSlot Integer32
  hwEntityFanSn Integer32
  hwEntityFanReg INTEGER
  hwEntityFanSpdAdjMode INTEGER
  hwEntityFanSpeed Integer32
  hwEntityFanPresent INTEGER
  hwEntityFanState INTEGER
  hwEntityFanDesc OCTET STRING

HwPortBip8StatisticsEntry  
SEQUENCE    
  hwPhysicalPortBip8StatisticsEB Counter64
  hwPhysicalPortBip8StatisticsES Counter64
  hwPhysicalPortBip8StatisticsSES Counter64
  hwPhysicalPortBip8StatisticsUAS Counter64
  hwPhysicalPortBip8StatisticsBBE Counter64
  hwPhysicalPortSpeed Unsigned32

HwStorageEntEntry  
SEQUENCE    
  hwStorageEntIndex Integer32
  hwStorageEntType Integer32
  hwStorageEntSpace Integer32
  hwStorageEntSpaceFree Integer32
  hwStorageEntName SnmpAdminString
  hwStorageEntDescr SnmpAdminString

HwSystemPowerEntry  
SEQUENCE    
  hwSystemPowerDeviceID Integer32
  hwSystemPowerTotalPower Integer32
  hwSystemPowerUsedPower Integer32
  hwSystemPowerRemainPower Integer32
  hwSystemPowerReservedPower Integer32

HwBatteryInfoEntry  
SEQUENCE    
  hwBatteryState INTEGER
  hwBatteryTemperatureLow Integer32
  hwBatteryTemperatureHigh Integer32
  hwBatteryRemainPercent Integer32
  hwBatteryRemainTime Integer32
  hwBatteryElecTimes Integer32
  hwBatteryLifeThreshold Integer32

HwAdmPortEntry  
SEQUENCE    
  hwAdmPortDescription OCTET STRING

HwPwrStatusEntry  
SEQUENCE    
  hwEntityPwrSlot Integer32
  hwEntityPwrSn Integer32
  hwEntityPwrReg INTEGER
  hwEntityPwrMode INTEGER
  hwEntityPwrPresent INTEGER
  hwEntityPwrState INTEGER
  hwEntityPwrCurrent Integer32
  hwEntityPwrVoltage Integer32
  hwEntityPwrDesc OCTET STRING

HwPnpOperateEntry  
SEQUENCE    
  hwFileGeneIndex Integer32
  hwFileGeneOperState INTEGER
  hwFileGeneResourceType INTEGER
  hwFileGeneResourceID SnmpAdminString
  hwFileGeneDestinationFile SnmpAdminString
  hwFileGeneRowStatus RowStatus

HwPreDisposeConfigEntry  
SEQUENCE    
  hwDisposeSlot Integer32
  hwDisposeCardId Integer32
  hwDisposeSbom OCTET STRING
  hwDisposeRowStatus RowStatus
  hwDisposeOperState INTEGER

HwPreDisposeEntInfoEntry  
SEQUENCE    
  hwDisposeEntPhysicalIndex PhysicalIndex
  hwDisposeEntPhysicalDescr SnmpAdminString
  hwDisposeEntPhysicalVendorType AutonomousType
  hwDisposeEntPhysicalContainedIn Integer32
  hwDisposeEntPhysicalClass PhysicalClass
  hwDisposeEntPhysicalParentRelPos Integer32
  hwDisposeEntPhysicalName SnmpAdminString

Defined Values

hwEntityExtentMIB 1.3.6.1.4.1.2011.5.25.31
The private mib file includes the general extent information of the device.
MODULE-IDENTITY    

hwEntityExtObjects 1.3.6.1.4.1.2011.5.25.31.1
OBJECT IDENTIFIER    

hwEntityState 1.3.6.1.4.1.2011.5.25.31.1.1
OBJECT IDENTIFIER    

hwEntityStateTable 1.3.6.1.4.1.2011.5.25.31.1.1.1
This table contains one row per physical entity, There is always at least one row for an 'overall' physical entity. The information in each row may be not include all the object in this table, because of the entity need not some of the information here.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwEntityStateEntry

hwEntityStateEntry 1.3.6.1.4.1.2011.5.25.31.1.1.1.1
Information about a particular physical entity. Each entry provides objects (entPhysicalDescr, entPhysicalVendorType, and entPhysicalClass) to help an NMS identify and characterize the entry, and objects (entPhysicalContainedIn and entPhysicalParentRelPos) to help an NMS relate the particular entry to other entries in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwEntityStateEntry  

hwEntityAdminStatus 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.1
The administrative state for this object, and it is possible to set the state when needed.
Status: current Access: read-write
OBJECT-TYPE    
  HwAdminState  

hwEntityOperStatus 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.2
The operational state for this object.
Status: current Access: read-only
OBJECT-TYPE    
  HwOperState  

hwEntityStandbyStatus 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.3
Some entity in a device can support standby mode, This object is used for monitoring standby status.
Status: current Access: read-only
OBJECT-TYPE    
  HwStandbyStatus  

hwEntityAlarmLight 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.4
The alarm status for this entity. It does not include the severity of alarms raised on child components. On the condition, there are a alarm light on the entity, the object should have the same status with it.
Status: current Access: read-only
OBJECT-TYPE    
  HwAlarmStatus  

hwEntityCpuUsage 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.5
The CPU usage for this entity. Generally, the CPU usage will calculate the overall CPU usage on the entity, and it is not sensible with the number of CPU on the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hwEntityCpuUsageThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.6
The threshold for the CPU usage. When the CPU usage exceed the threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

hwEntityMemUsage 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.7
The memory usage for the entity. This object point out how many percent of memory has been used.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hwEntityMemUsageThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.8
The threshold for the Memory usage, When the memory usage exceed the threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

hwEntityMemSize 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.9
The size of memory for the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityUpTime 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.10
The up time for the entity. The mean of up time is when the entity is up, and the value of the object will add one per seconds while the entity running.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityTemperature 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.11
The temperature for the entity. The value 0X7FFFFFF indicates invalid temperature.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityTemperatureThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.12
The threshold for the temperature. When the temperature exceeds the threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityVoltage 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.13
The voltage for the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityVoltageLowThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.14
The low-threshold for the voltage. Generally, we have two threshold for the voltage, one is low-threshold, and the other is high-threshold. the normal status of voltage should be greater than the low-threshold, and lower than the high-threshold. When the voltage low than the low-threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityVoltageHighThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.15
The high-threshold for the voltage. Generally, we have two threshold for the voltage, one is low-threshold, and the other is high-threshold. the normal status of voltage should be greater than the low-threshold, and lower than the high-threshold. When the voltage greater than the high-threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityTemperatureLowThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.16
The low-threshold of temperature. If the device temperature is lower than the threshold, an alarm is raised.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityOpticalPower 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.17
The optical power of the optical module. Unit: uW
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityCurrent 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.18
The current for the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityMemSizeMega 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.19
The size of SDRAM(Synchronous Dynamic Random Access Memory) memory for the entity. Unit: M bytes
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPortType 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.20
Indicates the type of the Ethernet interface: an optical interface or an electrical interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), copper(2), fiber100(3), fiber1000(4), fiber10000(5), opticalnotExist(6), optical(7)  

hwEntityDuplex 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.21
Indicates the duplex mode of the Ethernet interface. An electrical Ethernet interface can work in half-duplex mode or full-duplex mode. An optical Ethernet can work only in full-duplex mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), full(2), half(3)  

hwEntityOpticalPowerRx 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.22
The optical power(Rx) of the optical module. Unit: uW
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityCpuUsageLowThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.23
The threshold for the CPU usage. When the CPU usage exceed the threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

hwEntityBoardPower 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.24
The board power for the entity. Unit: W
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityCpuFrequency 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.25
The frequency of the entity. Unit: Hz
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntitySupportFlexCard 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.26
It describes whether the whole board supports flexible cards. When the board doesn't support flexible cards, the cards may be dummy ones whose ports will not be seen by the customer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), flexible(2), unflexible(3), dummy(4)  

hwEntityBoardClass 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.27
It describes the board type of the whole board.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), mpu(2), lpu(3), sfu(4), icu(5), ecu(6), fan(7), power(8), lcd(9), pmu(10), cmu(11)  

hwNseOpmStatus 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.28
OPM status. 0: pass, 1: bypass, 2: invalid
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2  

hwEntityCpuMaxUsage 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.29
The Max CPU usage for this entity. Generally, the Max CPU usage will calculate the overall CPU usage on the entity, and it is not sensible with the number of CPU on the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityCPUType 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.30
CPU type.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityMemoryType 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.31
Memory type.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityFlashSize 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.32
Flash size, in KB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityIfUpTimes 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.33
Times that the interface goes Up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityIfDownTimes 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.34
Times that the interface goes Down.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityCPUAvgUsage 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.35
Average CPU usage within a specified statistical interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityMemoryAvgUsage 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.36
Average memory usage within a specified statistical interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hwEntityMemUsed 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.37
The memory information for the entity. This object indicates how many bytes in the memory have been used.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwEntityTotalFanNum 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.38
The total numbers of the fans in the chassis .
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityNomalFanNum 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.39
The Nomal numbers of the fans in the chassis .
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityTotalPwrNum 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.40
The total numbers of the powers in the chassis .
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityNomalPwrNum 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.41
The nomal numbers of the powers in the chassis .
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityFaultLight 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.42
The repair status for this entity. On the underrepair condition, there is a blue light on the entity.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), normal(2), underRepair(3)  

hwEntityBoardName 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.43
The board name for this entity.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwEntityBoardDescription 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.44
The board description for this entity.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwEntity5MinCpuUsage 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.45
Average CPU usage of the last five minutes for this entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityStartMode 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.46
The start mode of board.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), cold(2), warm(3), unknown(4)  

hwEntitySplitAttribute 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.47
The attribute for the split port.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwEntityFaultLightKeepTime 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.48
Fault light twinkle keep time,the default is 45 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwRUModuleInfoTable 1.3.6.1.4.1.2011.5.25.31.1.1.2
This table contains one row per replaceable unit physical entity. The row with the field 'entPhysicalIsFRU' sets to 'true' in table 'entPhysicalTable' will be mapped to one row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwRUModuleInfoEntry

hwRUModuleInfoEntry 1.3.6.1.4.1.2011.5.25.31.1.1.2.1
Information about a replaceable unit physical entity. Each entry provides objects of a replaceable unit to help an NMS identify and characterize the entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwRUModuleInfoEntry  

hwEntityBomId 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.1
The identity of the Bill of Material about this replaceable unit which coded by vendor. This node is mapping to 'ITEM' in the information file.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityBomEnDesc 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.2
The English description of the Bill of Material about this replaceable unit.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityBomLocalDesc 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.3
The local description of the Bill of Material about this replaceable unit.
Status: obsolete Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityManufacturedDate 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.4
The date when this physical entity is Manufactured.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

hwEntityManufactureCode 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.5
The code of the place where this physical entity is Manufactured.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityCLEICode 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.6
The string code of CLEI which was granted by America.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityUpdateLog 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.7
The maintenance log of this replaceable unit.
Status: obsolete Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityArchivesInfoVersion 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.8
The Version of Archives Information.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityOpenBomId 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.9
The BomId for distribution. It is different from hwEntityBomId.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityIssueNum 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.10
The issue number for hardware change.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityBoardType 1.3.6.1.4.1.2011.5.25.31.1.1.2.1.11
The type code for entity.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwOpticalModuleInfoTable 1.3.6.1.4.1.2011.5.25.31.1.1.3
Table of optical module properties.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwOpticalModuleInfoEntry

hwOpticalModuleInfoEntry 1.3.6.1.4.1.2011.5.25.31.1.1.3.1
An entry in the table of optical module properties for each optical module.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwOpticalModuleInfoEntry  

hwEntityOpticalMode 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.1
The mode of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), singleMode(2), multiMode5(3), multiMode6(4), noValue(5)  

hwEntityOpticalWaveLength 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.2
The wave length of the optical module. Unit: nm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalTransDistance 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.3
The max transmission distance of the optical module. Unit: m.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalVendorSn 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.4
The vendor serial number (vendor SN) of the optical module. Length: 16 bytes.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntityOpticalTemperature 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.5
The current temperature of the optical module. Unit: C
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalVoltage 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.6
The current voltage of the optical module. Unit: mV.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalBiasCurrent 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.7
The bias current of the optical module. Unit: mA.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalRxPower 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.8
The receive power of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalTxPower 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.9
The transmit power of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalType 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.10
The type of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), sc(1), gbic(2), sfp(3), esfp(4), rj45(5), xfp(6), xenpak(7), transponder(8), cfp(9), smb(10), sfpplus(11), cxp(12), qsfp(13), qsfpplus(14), cfp2(15), dwdmsfp(16)  

hwEntityOpticalTransBW 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.11
The Transceiver max BW of the optical module.Unit:M
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalFiberType 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.12
The Fiber type of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), sc(1), style1CopperConnector(2), style2CopperConnector(3), bncTnc(4), coaxialHeaders(5), fiberJack(6), lc(7), mtRj(8), mu(9), sg(10), opticalPigtail(11), hssdcII(20), mpo(12), copperPigtail(21)  

hwEntityOpticalRxLowThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.13
The receive power low threshold of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalRxHighThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.14
The receive power high threshold of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalTxLowThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.15
The transmit power low threshold of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalTxHighThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.16
The transmit power high threshold of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalPlug 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.17
The optical module is plug-supported or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(0), true(1), false(2)  

hwEntityOpticalDirectionType 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.18
The direction type of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), twoFiberBidirection(2), oneFiberBidirection(3), twoFiberTwoPortBidirection(4)  

hwEntityOpticalUserEeprom 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.19
The user writable EEPROM of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..120)  

hwEntityOpticalRxLowWarnThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.20
The receive power low warning threshold of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalRxHighWarnThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.21
The receive power high warning threshold of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalTxLowWarnThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.22
The transmit power low warning threshold of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalTxHighWarnThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.23
The transmit power high warning threshold of the optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalVenderName 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.24
The Vender Name of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..120)  

hwEntityOpticalVenderPn 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.25
The Vender PN of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..120)  

hwEntityOpticalAuthenticationStatus 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.26
The authentication status of optical module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), authenticated(1), unauthenticated(2)  

hwEntityOpticalTunableType 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.27
The tunable type of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), notTunable(2), tunable(3), supportTunableType(4)  

hwEntityOpticalWaveLengthDecimal 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.28
The Decimal wavelength of the optical module. Unit: nm. The value is expanded 1000 times,so the real value should be reduced 1000 times.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalTunableModuleChannel 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.29
The current channel of tunable optical module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityOpticalWaveBand 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.30
The wave band of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), clBand(1), cBand(2), lBand(3), c32Band(4), ramancBand(5), ramanlBand(6), cwdmBand(7), smcBand(8), c96bBand(9), c192bBand(10)  

hwEntityOpticalLaneBiasCurrent 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.31
The bias current of the QSFP or CFP optical module. Unit: mA.(e.g., 37.88,39.15,39.84,37.82)
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

hwEntityOpticalLaneRxPower 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.32
The receive power of the QSFP or CFP optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times (e.g., 114,32,-90,-228)
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

hwEntityOpticalLaneTxPower 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.33
The transmit power of the QSFP or CFP optical module. Unit: dBm. the value is expanded 100 times,so the real value should be reduced 100 times (e.g., 94,-39,33,-58)
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

hwEntityOpticalVendorOUI 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.34
Vendor ID of the optical module assigned by IEEE.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

hwEntityOpticalVendorRev 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.35
The Vender Version of the optical module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

hwEntityOpticalGponSN 1.3.6.1.4.1.2011.5.25.31.1.1.3.1.36
The SN of the optical module provided by the vendor.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

hwMonitorInputTable 1.3.6.1.4.1.2011.5.25.31.1.1.4
This table contains one row per replaceable unit physical entity. This table is used to set the status of monitor port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMonitorInputEntry

hwMonitorInputEntry 1.3.6.1.4.1.2011.5.25.31.1.1.4.1
This is a replaceable unit physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMonitorInputEntry  

hwMonitorInputIndex 1.3.6.1.4.1.2011.5.25.31.1.1.4.1.1
Monitor port index. This is a number of input line,ranging from 1 to 4.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

hwMonitorInputName 1.3.6.1.4.1.2011.5.25.31.1.1.4.1.2
Monitor line name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

hwMonitorInputState 1.3.6.1.4.1.2011.5.25.31.1.1.4.1.3
Monitor line status. The value is high or low.
Status: current Access: read-create
OBJECT-TYPE    
  HWLevelState  

hwMonitorInputStateEnable 1.3.6.1.4.1.2011.5.25.31.1.1.4.1.4
Enable monitor line.
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwMonitorInputRowStatus 1.3.6.1.4.1.2011.5.25.31.1.1.4.1.5
Status of monitor input row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMonitorOutputTable 1.3.6.1.4.1.2011.5.25.31.1.1.5
This table contains one row per replaceable unit physical entity. This table is used to create a output view.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMonitorOutputEntry

hwMonitorOutputEntry 1.3.6.1.4.1.2011.5.25.31.1.1.5.1
This is a replaceable unit physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMonitorOutputEntry  

hwMonitorOutputIndex 1.3.6.1.4.1.2011.5.25.31.1.1.5.1.1
Monitor output view index. Through this index ,you can turn into the output view.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..3  

hwMonitorOutputRuleIndex 1.3.6.1.4.1.2011.5.25.31.1.1.5.1.2
Monitor output rule index. This is used to set the rules about all of the input line.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

hwMonitorOutputMask 1.3.6.1.4.1.2011.5.25.31.1.1.5.1.3
Monitor output mask . This is used to matching the level of monitor input line.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

hwMonitorOutputKey 1.3.6.1.4.1.2011.5.25.31.1.1.5.1.4
Normal level value of this output line.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

hwMonitorOutputRowStatus 1.3.6.1.4.1.2011.5.25.31.1.1.5.1.5
Status of monitor input row
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwEntPowerUsedInfoTable 1.3.6.1.4.1.2011.5.25.31.1.1.6
A table of information that displays the power use of entity .
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwEntPowerUsedInfoEntry

hwEntPowerUsedInfoEntry 1.3.6.1.4.1.2011.5.25.31.1.1.6.1
Entry of the table of information that displays the power use of entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwEntPowerUsedInfoEntry  

hwEntPowerUsedInfoBoardName 1.3.6.1.4.1.2011.5.25.31.1.1.6.1.1
Board name.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwEntPowerUsedInfoBoardType 1.3.6.1.4.1.2011.5.25.31.1.1.6.1.2
Board type.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwEntPowerUsedInfoBoardSlot 1.3.6.1.4.1.2011.5.25.31.1.1.6.1.3
Board's slot number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntPowerUsedInfoPower 1.3.6.1.4.1.2011.5.25.31.1.1.6.1.4
Used power of board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwVirtualCableTestTable 1.3.6.1.4.1.2011.5.25.31.1.1.7
This table contains one row per replaceable unit physical entity. This table is used to display VCT result.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVirtualCableTestEntry

hwVirtualCableTestEntry 1.3.6.1.4.1.2011.5.25.31.1.1.7.1
This is a replaceable unit physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVirtualCableTestEntry  

hwVirtualCableTestIfIndex 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.1
IfIndex of port that you want to test cable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwVirtualCableTestPairStatus 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.2
Pair status. This indicate the status of cable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), abnormalOpen(2), abnormalShort(3), abnormalOpenShort(4), abnormalCrossTalk(5), unknown(6), notSupport(7)  

hwVirtualCableTestPairLength 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.3
Pair Length. This indicate the length of cable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwVirtualCableTestOperation 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.4
VirtualCableTestOperation. This Operation of VirtualCableTest.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER startTest(1), resetTestValue(2), readyStartTest(3)  

hwVirtualCableTestLastTime 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.5
The last test time for the entity. The mean of last time is when the entity is tested, and the value of the object will add one per seconds until now.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwVirtualCableTestPairAStatus 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.6
Pair A status. This indicate the status of cable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), abnormalOpen(2), abnormalShort(3), abnormalOpenShort(4), abnormalCrossTalk(5), unknown(6), notSupport(7)  

hwVirtualCableTestPairBStatus 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.7
Pair B status. This indicate the status of cable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), abnormalOpen(2), abnormalShort(3), abnormalOpenShort(4), abnormalCrossTalk(5), unknown(6), notSupport(7)  

hwVirtualCableTestPairCStatus 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.8
Pair C status. This indicate the status of cable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), abnormalOpen(2), abnormalShort(3), abnormalOpenShort(4), abnormalCrossTalk(5), unknown(6), notSupport(7)  

hwVirtualCableTestPairDStatus 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.9
Pair D status. This indicate the status of cable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), abnormalOpen(2), abnormalShort(3), abnormalOpenShort(4), abnormalCrossTalk(5), unknown(6), notSupport(7)  

hwVirtualCableTestPairALength 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.10
Pair A Length. This indicate the length of cable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwVirtualCableTestPairBLength 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.11
Pair B Length. This indicate the length of cable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwVirtualCableTestPairCLength 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.12
Pair C Length. This indicate the length of cable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwVirtualCableTestPairDLength 1.3.6.1.4.1.2011.5.25.31.1.1.7.1.13
Pair D Length. This indicate the length of cable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwTemperatureThresholdTable 1.3.6.1.4.1.2011.5.25.31.1.1.8
This table lists the alarm thresholds of temperature sensors. You can read information about all the temperature sensors of the device. You can set the alarm threshold of a specified temperature sensor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwTemperatureThresholdEntry

hwTemperatureThresholdEntry 1.3.6.1.4.1.2011.5.25.31.1.1.8.1
Defines an entry in the hwTemperatureThresholdTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwTemperatureThresholdEntry  

hwEntityTempSlotId 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.1
This object indicates the slot ID of a temperature sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityTempI2CId 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.2
This object indicates the I2CID of a temperature sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityTempAddr 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.3
This object indicates the address of a temperature sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityTempChannel 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.4
This object indicates the channel of a temperature sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityTempStatus 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.5
This object indicates the current status of a temperature sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), minor(2), major(3), fatal(4)  

hwEntityTempValue 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.6
This object indicates the current value in Celsius of a temperature sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityTempMinorAlmThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.7
This object indicates the threshold for a minor alarm. The value can be set and ranges from 80% to 120% of the default value. The value is in Celsius.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityTempMajorAlmThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.8
This object indicates the threshold for a major alarm. The value can be set and ranges from 80% to 120% of the default value. The value is in Celsius.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityTempFatalAlmThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.8.1.9
This object indicates the threshold for a fatal alarm. The value can be set and ranges from 80% to 120% of the default value. The value is in Celsius.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwVoltageInfoTable 1.3.6.1.4.1.2011.5.25.31.1.1.9
This table lists information about voltage sensors. You can read information about all the voltage sensors of the device. You can set the alarm threshold of a specified voltage sensor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVoltageInfoEntry

hwVoltageInfoEntry 1.3.6.1.4.1.2011.5.25.31.1.1.9.1
Defines an entry in the hwVoltageInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVoltageInfoEntry  

hwEntityVolSlot 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.1
This object indicates the slot ID of a voltage sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityVolI2CId 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.2
This object indicates the I2CID of a voltage sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityVolAddr 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.3
This object indicates the address of a voltage sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityVolChannel 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.4
This object indicates the channel of a voltage sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityVolStatus 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.5
This object indicates the current status of a voltage sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), major(2), fatal(3)  

hwEntityVolRequired 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.6
This object indicates the nominal value in millivolt of a voltage sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityVolCurValue 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.7
This object indicates the current value in millivolt of a voltage sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityVolRatio 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.8
This object indicates the voltage ratio of a voltage sensor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityVolLowAlmMajor 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.9
This object indicates the threshold for a major alarm of low voltage. The value can be set and ranges from 80% to 120% of the default value. The value is in millivolt.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityVolLowAlmFatal 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.10
This object indicates the threshold for a fatal alarm of low voltage. The value can be set and ranges from 80% to 120% of the default value. The value is in millivolt.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityVolHighAlmMajor 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.11
This object indicates the threshold for a major alarm of high voltage. The value can be set and ranges from 80% to 120% of the default value. The value is in millivolt.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwEntityVolHighAlmFatal 1.3.6.1.4.1.2011.5.25.31.1.1.9.1.12
This object indicates the threshold for a fatal alarm of high voltage. The value can be set and ranges from 80% to 120% of the default value. The value is in millivolt.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwFanStatusTable 1.3.6.1.4.1.2011.5.25.31.1.1.10
This table lists the status of fans. You can read the status of the fans on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwFanStatusEntry

hwFanStatusEntry 1.3.6.1.4.1.2011.5.25.31.1.1.10.1
Defines an entry in the hwFanStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwFanStatusEntry  

hwEntityFanSlot 1.3.6.1.4.1.2011.5.25.31.1.1.10.1.1
This object indicates the slot ID of a fan.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityFanSn 1.3.6.1.4.1.2011.5.25.31.1.1.10.1.2
This object indicates the serial number of the fan in a certain slot.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityFanReg 1.3.6.1.4.1.2011.5.25.31.1.1.10.1.3
This object indicates whether the fan is registered.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

hwEntityFanSpdAdjMode 1.3.6.1.4.1.2011.5.25.31.1.1.10.1.4
This object indicates the speed adjustment mode of the fan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER auto(1), manual(2), unknown(3)  

hwEntityFanSpeed 1.3.6.1.4.1.2011.5.25.31.1.1.10.1.5
This object indicates the rotation speed (in percentage of the full speed) of the fan.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityFanPresent 1.3.6.1.4.1.2011.5.25.31.1.1.10.1.6
This object indicates the present information of the fan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER present(1), absent(2)  

hwEntityFanState 1.3.6.1.4.1.2011.5.25.31.1.1.10.1.7
This object indicates the state of the fan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), abnormal(2)  

hwEntityFanDesc 1.3.6.1.4.1.2011.5.25.31.1.1.10.1.8
This object indicates the description of the fan.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwEntityGlobalPara 1.3.6.1.4.1.2011.5.25.31.1.1.11
OBJECT IDENTIFIER    

hwEntityServiceType 1.3.6.1.4.1.2011.5.25.31.1.1.11.1
It describes the service-type of spu board .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sslvpn(1), firewall(2), loadBalance(3), ipsec(4), netstream(5), wlan(6)  

hwDeviceServiceType 1.3.6.1.4.1.2011.5.25.31.1.1.11.2
It describes the service-type of the device. bit0 is WLAN, bit1 is SSLVPN, bit2 is ipsec,other bits temporarily without easy back extension. Each bit 0 is disable, 1 is enable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityManufacturerOUI 1.3.6.1.4.1.2011.5.25.31.1.1.11.3
It describes the Manufacturer of the device.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwPortBip8StatisticsTable 1.3.6.1.4.1.2011.5.25.31.1.1.12
Indicates the BIP8 statistics. This table lists the various BIP8 statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortBip8StatisticsEntry

hwPortBip8StatisticsEntry 1.3.6.1.4.1.2011.5.25.31.1.1.12.1
Indicates the BIP8 statistics. This table lists the various BIP8 statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwPortBip8StatisticsEntry  

hwPhysicalPortBip8StatisticsEB 1.3.6.1.4.1.2011.5.25.31.1.1.12.1.1
BIP8 Statistics: EB(Errored Block).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPhysicalPortBip8StatisticsES 1.3.6.1.4.1.2011.5.25.31.1.1.12.1.2
BIP8 Statistics: ES(Errored Second).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPhysicalPortBip8StatisticsSES 1.3.6.1.4.1.2011.5.25.31.1.1.12.1.3
BIP8 Statistics: SES(Severely Errored Second).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPhysicalPortBip8StatisticsUAS 1.3.6.1.4.1.2011.5.25.31.1.1.12.1.4
BIP8 Statistics: UAS(Unavailable Errored Second).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPhysicalPortBip8StatisticsBBE 1.3.6.1.4.1.2011.5.25.31.1.1.12.1.5
BIP8 Statistics: BBE(Background Block Error).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPhysicalPortSpeed 1.3.6.1.4.1.2011.5.25.31.1.1.12.1.6
An estimate of the interface's current bandwidth in 1000000 bits per second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwStorageEntTable 1.3.6.1.4.1.2011.5.25.31.1.1.13
Indicates the Storage statistics
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwStorageEntEntry

hwStorageEntEntry 1.3.6.1.4.1.2011.5.25.31.1.1.13.1
Indicates the Storage statistics. This table lists the Entity Storage statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwStorageEntEntry  

hwStorageEntIndex 1.3.6.1.4.1.2011.5.25.31.1.1.13.1.1
The Index of Storage statistics.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwStorageEntType 1.3.6.1.4.1.2011.5.25.31.1.1.13.1.2
The Type of Storage.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwStorageEntSpace 1.3.6.1.4.1.2011.5.25.31.1.1.13.1.3
The Size of Storage.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwStorageEntSpaceFree 1.3.6.1.4.1.2011.5.25.31.1.1.13.1.4
The Free Size of Storage.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwStorageEntName 1.3.6.1.4.1.2011.5.25.31.1.1.13.1.5
The Name of Storage.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwStorageEntDescr 1.3.6.1.4.1.2011.5.25.31.1.1.13.1.6
The Description of Storage.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwSystemPowerTable 1.3.6.1.4.1.2011.5.25.31.1.1.14
System power infomation table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwSystemPowerEntry

hwSystemPowerEntry 1.3.6.1.4.1.2011.5.25.31.1.1.14.1
System power infomation entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwSystemPowerEntry  

hwSystemPowerDeviceID 1.3.6.1.4.1.2011.5.25.31.1.1.14.1.1
System power infomation device ID.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwSystemPowerTotalPower 1.3.6.1.4.1.2011.5.25.31.1.1.14.1.2
System power infomation total power.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwSystemPowerUsedPower 1.3.6.1.4.1.2011.5.25.31.1.1.14.1.3
System power infomation used power.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwSystemPowerRemainPower 1.3.6.1.4.1.2011.5.25.31.1.1.14.1.4
System power infomation remain power.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwSystemPowerReservedPower 1.3.6.1.4.1.2011.5.25.31.1.1.14.1.5
System power infomation reserved power.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwBatteryInfoTable 1.3.6.1.4.1.2011.5.25.31.1.1.15
Description.Battery information table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwBatteryInfoEntry

hwBatteryInfoEntry 1.3.6.1.4.1.2011.5.25.31.1.1.15.1
Description.Battery information entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HwBatteryInfoEntry  

hwBatteryState 1.3.6.1.4.1.2011.5.25.31.1.1.15.1.1
Description.The state of lithium battery.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER charge(1), discharge(2), full(3), abnormal(4)  

hwBatteryTemperatureLow 1.3.6.1.4.1.2011.5.25.31.1.1.15.1.2
Description.The lowest temperature of lithium battery.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwBatteryTemperatureHigh 1.3.6.1.4.1.2011.5.25.31.1.1.15.1.3
Description.The highest temperature of lithium battery.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwBatteryRemainPercent 1.3.6.1.4.1.2011.5.25.31.1.1.15.1.4
Description. The remained electricity quantity percent of lithium battery,unit in minute.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwBatteryRemainTime 1.3.6.1.4.1.2011.5.25.31.1.1.15.1.5
Description. The remained time of lithium battery.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwBatteryElecTimes 1.3.6.1.4.1.2011.5.25.31.1.1.15.1.6
Description.The charge and discharge times of lithium battery.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwBatteryLifeThreshold 1.3.6.1.4.1.2011.5.25.31.1.1.15.1.7
Description.The warning threshold of lithium battery's lifetime.(unit in minute,the default value is 20)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwGPSLocationInfo 1.3.6.1.4.1.2011.5.25.31.1.1.16
OBJECT IDENTIFIER    

hwGPSLongitude 1.3.6.1.4.1.2011.5.25.31.1.1.16.1
Description.The longitude of the device location.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwGPSLatitude 1.3.6.1.4.1.2011.5.25.31.1.1.16.2
Description.The latidude of the device location.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwGPSVelocity 1.3.6.1.4.1.2011.5.25.31.1.1.16.3
Description.The velocity of the device.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwAdmPortTable 1.3.6.1.4.1.2011.5.25.31.1.1.17
The table of ADM(Add/Drop Multiplexer) port properties.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwAdmPortEntry

hwAdmPortEntry 1.3.6.1.4.1.2011.5.25.31.1.1.17.1
The entry of ADM(Add/Drop Multiplexer) port properties table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwAdmPortEntry  

hwAdmPortDescription 1.3.6.1.4.1.2011.5.25.31.1.1.17.1.1
The description of ADM(Add/Drop Multiplexer) port.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwPwrStatusTable 1.3.6.1.4.1.2011.5.25.31.1.1.18
This table lists the status of powers. You can read the status of the powers on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwPwrStatusEntry

hwPwrStatusEntry 1.3.6.1.4.1.2011.5.25.31.1.1.18.1
Defines an entry in the hwPwrStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwPwrStatusEntry  

hwEntityPwrSlot 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.1
This object indicates the slot ID of a power.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPwrSn 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.2
This object indicates the serial number of the power in a certain slot.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPwrReg 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.3
This object indicates whether the power is registered.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

hwEntityPwrMode 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.4
This object indicates the mode of the power.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), dc(2), ac(3)  

hwEntityPwrPresent 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.5
This object indicates the present information of the power.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER present(1), absent(2)  

hwEntityPwrState 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.6
This object indicates the state of the power.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER supply(1), notSupply(2), sleep(3), unknown(4)  

hwEntityPwrCurrent 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.7
This object indicates the current of the power. Unit: mA
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPwrVoltage 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.8
This object indicates the voltage of the power. Unit: mV
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPwrDesc 1.3.6.1.4.1.2011.5.25.31.1.1.18.1.9
This object indicates the description of the power.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwEntityPhysicalSpecTable 1.3.6.1.4.1.2011.5.25.31.1.2
OBJECT IDENTIFIER    

hwEntityPhysicalSpecRack 1.3.6.1.4.1.2011.5.25.31.1.2.1
The rack coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecFrame 1.3.6.1.4.1.2011.5.25.31.1.2.2
The frame coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecSlot 1.3.6.1.4.1.2011.5.25.31.1.2.3
The slot coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecBoard 1.3.6.1.4.1.2011.5.25.31.1.2.4
The board coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecSubSlot 1.3.6.1.4.1.2011.5.25.31.1.2.5
The sub slot coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecSubBoard 1.3.6.1.4.1.2011.5.25.31.1.2.6
The sub board coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecPort 1.3.6.1.4.1.2011.5.25.31.1.2.7
The port coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecEmu 1.3.6.1.4.1.2011.5.25.31.1.2.8
The EMU(Environment monitoring unit) coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecPowerframe 1.3.6.1.4.1.2011.5.25.31.1.2.9
The power frame coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecPowermodule 1.3.6.1.4.1.2011.5.25.31.1.2.10
The power module coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityPhysicalSpecBattery 1.3.6.1.4.1.2011.5.25.31.1.2.11
The battery coefficient used for calculating the index of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityExtTraps 1.3.6.1.4.1.2011.5.25.31.2
OBJECT IDENTIFIER    

hwEntityExtTrapsPrefix 1.3.6.1.4.1.2011.5.25.31.2.0
OBJECT IDENTIFIER    

hwEntityExtTemperatureThresholdNotification 1.3.6.1.4.1.2011.5.25.31.2.0.1
The hwEntityEnvTemperatureThresholdNotification indicates the temperature have been exceed the threshold. In the condition, user should check the hardware and the environment of the entity, sometimes it happened because of the failture of air-condition. Anyway, the threshold should lower than the value that most service work fine.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtVoltageLowThresholdNotification 1.3.6.1.4.1.2011.5.25.31.2.0.2
The hwEntityExtVoltageLowThresholdNotification indicates the voltage is lower than the threshold. This may decrease the usability of the entity. If the voltage is lower too much than the hardware needed, the entity will stop working. Anyway, the threshold should higher than the value that most service work fine.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtVoltageHighThresholdNotification 1.3.6.1.4.1.2011.5.25.31.2.0.3
The hwEntityExtVoltageHighThresholdNotification indicates the voltage is higher than the threshold. This may decrease the usability of the entity. If the voltage is higher too much than the hardware needed, the entity may be destroyed by the high voltage. Anyway, the threshold should lower than the value that most service work fine.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtCpuUsageThresholdNotfication 1.3.6.1.4.1.2011.5.25.31.2.0.4
The hwEntityExtCpuUsageThresholdNotfication indicates the entity is overload, and the service running in the entity will not get the performance it should because of CPU's performance. Anyway, the threshold should lower than the value that most service work fine.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtMemUsageThresholdNotification 1.3.6.1.4.1.2011.5.25.31.2.0.5
The hwEntityExtMemUsageThresholdNotification indicates the entity is overload, and the service running in the entity will not get the performance it should because of lower memory. Anyway, the threshold should lower than the value that most service work fine.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtOperEnabled 1.3.6.1.4.1.2011.5.25.31.2.0.6
The entity is operational. The entity this notification refers can be identified by extracting the entPhysicalIndex from one of the variable bindings.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtOperDisabled 1.3.6.1.4.1.2011.5.25.31.2.0.7
The entity is operational. The entity this notification refers can be identified by extracting the entPhysicalIndex from one of the variable bindings.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtMonitorBoardAbnormalNotification 1.3.6.1.4.1.2011.5.25.31.2.0.8
The monitor board turns normal to abnormal.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtMonitorBoardNormalNotification 1.3.6.1.4.1.2011.5.25.31.2.0.9
The monitor board turns abnormal to normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtMonitorPortAbnormalNotification 1.3.6.1.4.1.2011.5.25.31.2.0.10
The monitor port turns normal to abnormal.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtMonitorPortNormalNotification 1.3.6.1.4.1.2011.5.25.31.2.0.11
The monitor port turns abnormal to normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtCpuUsageLowThresholdNotfication 1.3.6.1.4.1.2011.5.25.31.2.0.12
The hwEntityExtCpuUsageThresholdNotfication indicates the entity is overload, and the service running in the entity will not get the performance it should because of CPU's performance. Anyway, the threshold should lower than the value that most service work fine.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtTrapObject 1.3.6.1.4.1.2011.5.25.31.2.1
OBJECT IDENTIFIER    

hwEntityExtTrapBaseSoftwareVersion 1.3.6.1.4.1.2011.5.25.31.2.1.1
System bassic software version.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING  

hwEntityExtTrapBoardSoftwareVersion 1.3.6.1.4.1.2011.5.25.31.2.1.2
Board software version compare to basic software version.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING  

hwPhysicalName 1.3.6.1.4.1.2011.5.25.31.2.1.3
The textual name of the physical entity. The value of this object should be the name of the component as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `console' or a simple component number (e.g., port or module number), such as `1', depending on the physical component naming syntax of the device. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string. Note that the value of entPhysicalName for two physical entities will be the same in the event that the console interface does not distinguish between them, e.g., slot-1 and the card in slot-1.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwEntityExtTrap 1.3.6.1.4.1.2011.5.25.31.2.2
OBJECT IDENTIFIER    

hwBoardSoftwareVersionIncompatible 1.3.6.1.4.1.2011.5.25.31.2.2.1
Board software version incompatible with basic software version.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwBoardSplitPorts 1.3.6.1.4.1.2011.5.25.31.2.2.2
When the split ports exist on the board, send a SNMP trap to network manager.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwDevicePowerInfoObjects 1.3.6.1.4.1.2011.5.25.31.3
OBJECT IDENTIFIER    

hwDevicePowerInfoTotalPower 1.3.6.1.4.1.2011.5.25.31.3.1
Device total power.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwDevicePowerInfoUsedPower 1.3.6.1.4.1.2011.5.25.31.3.2
Device used power.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwEntityExtConformance 1.3.6.1.4.1.2011.5.25.31.4
OBJECT IDENTIFIER    

hwEntityExtCompliances 1.3.6.1.4.1.2011.5.25.31.4.1
OBJECT IDENTIFIER    

hwEntityExtCompliance 1.3.6.1.4.1.2011.5.25.31.4.1.1
The compliance statement for systems supporting the HUAWEI Entity extent MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

hwEntityExtGroups 1.3.6.1.4.1.2011.5.25.31.4.2
OBJECT IDENTIFIER    

hwEntityExtGroup 1.3.6.1.4.1.2011.5.25.31.4.2.1
Standard HUAWEI Entity Extent group.
Status: current Access: read-only
OBJECT-GROUP    

hwEntityExtNotificationGroup 1.3.6.1.4.1.2011.5.25.31.4.2.2
Standard HUAWEI Entity Extent Notification group.
Status: current Access: read-only
NOTIFICATION-GROUP    

hwRUModuleInfoGroup 1.3.6.1.4.1.2011.5.25.31.4.2.3
Standard HUAWEI Entity Extent group.
Status: current Access: read-only
OBJECT-GROUP    

hwEntityExtOldObjectsGroup 1.3.6.1.4.1.2011.5.25.31.4.2.4
Group for old objects that may be obsoleted.
Status: obsolete Access: read-only
OBJECT-GROUP    

hwOpticalModuleInfoGroup 1.3.6.1.4.1.2011.5.25.31.4.2.5
Collection of objects that display the fiber module working information.
Status: current Access: read-only
OBJECT-GROUP    

hwMonitorInputGroup 1.3.6.1.4.1.2011.5.25.31.4.2.6
Standard HUAWEI Entity Extent group.
Status: current Access: read-only
OBJECT-GROUP    

hwMonitorOutputGroup 1.3.6.1.4.1.2011.5.25.31.4.2.7
Standard HUAWEI Entity Extent group.
Status: current Access: read-only
OBJECT-GROUP    

hwEntPowerUsedInfoGroup 1.3.6.1.4.1.2011.5.25.31.4.2.8
Collection of objects that display the power informations of entity.
Status: current Access: read-only
OBJECT-GROUP    

hwDevicePowerInfoGroup 1.3.6.1.4.1.2011.5.25.31.4.2.9
Collection of objects that display the power informations of device.
Status: current Access: read-only
OBJECT-GROUP    

hwVirtualCableTestGroup 1.3.6.1.4.1.2011.5.25.31.4.2.10
Collection of objects that display the status of cable.
Status: current Access: read-only
OBJECT-GROUP    

hwTemperatureThresholdGroup 1.3.6.1.4.1.2011.5.25.31.4.2.11
Temperature threshold group.
Status: current Access: read-only
OBJECT-GROUP    

hwVoltageInfoGroup 1.3.6.1.4.1.2011.5.25.31.4.2.12
Voltage info group.
Status: current Access: read-only
OBJECT-GROUP    

hwFanStatusGroup 1.3.6.1.4.1.2011.5.25.31.4.2.13
fan state group.
Status: current Access: read-only
OBJECT-GROUP    

hwPnpGroup 1.3.6.1.4.1.2011.5.25.31.4.2.14
Pnp group.
Status: current Access: read-only
OBJECT-GROUP    

hwSystemGlobalGroup 1.3.6.1.4.1.2011.5.25.31.4.2.15
System global group.
Status: current Access: read-only
OBJECT-GROUP    

hwHeartbeatGroup 1.3.6.1.4.1.2011.5.25.31.4.2.16
Heart beat group.
Status: current Access: read-only
OBJECT-GROUP    

hwPortBip8StatisticsObjectGroup 1.3.6.1.4.1.2011.5.25.31.4.2.17
The BIP8 statistics group.
Status: current Access: read-only
OBJECT-GROUP    

hwPredisposeGroup 1.3.6.1.4.1.2011.5.25.31.4.2.18
Pnp group.
Status: current Access: read-only
OBJECT-GROUP    

hwSystemPowerGroup 1.3.6.1.4.1.2011.5.25.31.4.2.19
Description.
Status: current Access: read-only
OBJECT-GROUP    

hwX86BoardGroup 1.3.6.1.4.1.2011.5.25.31.4.2.20
X86 group.
Status: current Access: read-only
NOTIFICATION-GROUP    

hwPwrStatusGroup 1.3.6.1.4.1.2011.5.25.31.4.2.21
pwr state group.
Status: current Access: read-only
OBJECT-GROUP    

hwPnpObjects 1.3.6.1.4.1.2011.5.25.31.5
OBJECT IDENTIFIER    

hwPnpInfo 1.3.6.1.4.1.2011.5.25.31.5.1
OBJECT IDENTIFIER    

hwHardwareCapaSequenceNo 1.3.6.1.4.1.2011.5.25.31.5.1.1
This object indicates the sequence number of the 'hardware capability file'.The value consists of the file version number and CRC code.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwAlarmPnPSequenceNo 1.3.6.1.4.1.2011.5.25.31.5.1.2
This object indicates the sequence number of the 'alarm capability file'.The value consists of the file version number and CRC code.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwPnpTraps 1.3.6.1.4.1.2011.5.25.31.5.2
OBJECT IDENTIFIER    

hwHardwareCapaChangeNotification 1.3.6.1.4.1.2011.5.25.31.5.2.1
This object indicates the change of the 'hardware capability file'. An alarm is generated if the sequence number of the 'hardware capability file' in the current startup file is different from that in the last startup file.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwAlarmPnPChangeNotification 1.3.6.1.4.1.2011.5.25.31.5.2.2
This object indicates the change of the 'alarm capability file'. An alarm is generated if the sequence number of the 'alarm capability file' in the current startup file is different from that in the last startup file.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPnpOperateTable 1.3.6.1.4.1.2011.5.25.31.5.3
This table describes the hardware functions. Using this table, you can obtain the specified 'hardware description file' or 'hardware capability file'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwPnpOperateEntry

hwPnpOperateEntry 1.3.6.1.4.1.2011.5.25.31.5.3.1
Status: current Access: not-accessible
OBJECT-TYPE    
  HwPnpOperateEntry  

hwFileGeneIndex 1.3.6.1.4.1.2011.5.25.31.5.3.1.1
The value of this object identifies the operation index, which can be specified by the user. The value ranges from 1 to 2147483647.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

hwFileGeneOperState 1.3.6.1.4.1.2011.5.25.31.5.3.1.2
The value of this object identifies the operation status. opInProgress(1): The operation is ongoing. opSuccess(2): The operation succeeds. opGetFileError(3): Obtaining the file fails. opInvalidDestName(4): The specified storage path is invalid. opNoFlashSpace(5): The space in the flash memory is insufficient. opWriteFileError(6): Writing the file fails. opDestoryError(7): Deleting the file fails.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER opInProgress(1), opSuccess(2), opGetFileError(3), opInvalidDestName(4), opNoFlashSpace(5), opWriteFileError(6), opDestoryError(7)  

hwFileGeneResourceType 1.3.6.1.4.1.2011.5.25.31.5.3.1.3
This object indicates the type of the file to be obtained. pnpcard(1): board description file pnpcard(2): subcard description file pnphardcapability(3): hardware capability file pnpPreDisposeCapability(4): predispose capability file pnpframe(5):frame description file pnpdevtype(6):device description file pnpalarm(7):alarm description file
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pnpcard(1), pnpsubcard(2), pnphardcapability(3), pnpPreDisposeCapability(4), pnpframe(5), pnpdevtype(6), pnpalarm(7)  

hwFileGeneResourceID 1.3.6.1.4.1.2011.5.25.31.5.3.1.4
This object indicates the ID of the 'hardware capability file' to be obtained.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

hwFileGeneDestinationFile 1.3.6.1.4.1.2011.5.25.31.5.3.1.5
This object indicates the target path storing the file, which does not need to be specified.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

hwFileGeneRowStatus 1.3.6.1.4.1.2011.5.25.31.5.3.1.6
This object indicates the row status. active(1) notInService(2) notReady(3) createAndGo(4) createAndWait(5) destroy(6)
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwSystemGlobalObjects 1.3.6.1.4.1.2011.5.25.31.6
OBJECT IDENTIFIER    

hwEntitySystemNetID 1.3.6.1.4.1.2011.5.25.31.6.1
Network element ID.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwEntitySoftwareName 1.3.6.1.4.1.2011.5.25.31.6.2
System software name.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntitySoftwareVersion 1.3.6.1.4.1.2011.5.25.31.6.3
Software version number.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntitySoftwareVendor 1.3.6.1.4.1.2011.5.25.31.6.4
Software vendor.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntitySystemModel 1.3.6.1.4.1.2011.5.25.31.6.5
Device model.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntitySystemTime 1.3.6.1.4.1.2011.5.25.31.6.6
System time displayed on the device.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

hwEntitySystemMacAddress 1.3.6.1.4.1.2011.5.25.31.6.7
MAC address of the device.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwEntitySystemReset 1.3.6.1.4.1.2011.5.25.31.6.8
System reset.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), restart(2)  

hwEntitySystemHealthInterval 1.3.6.1.4.1.2011.5.25.31.6.9
Statistical interval for average CPU and memory usage, in seconds (By default, the value is 300) .
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..900  

hwEntitySystemNEId 1.3.6.1.4.1.2011.5.25.31.6.10
Systme NEId.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..16777215  

hwEntitySystemServiceType 1.3.6.1.4.1.2011.5.25.31.6.11
System service type.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwHeartbeatObjects 1.3.6.1.4.1.2011.5.25.31.7
OBJECT IDENTIFIER    

hwHeartbeatConfig 1.3.6.1.4.1.2011.5.25.31.7.1
OBJECT IDENTIFIER    

hwEntityHeartbeatOnOff 1.3.6.1.4.1.2011.5.25.31.7.1.1
Whether Heartbeat sending periodically enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

hwEntityHeartbeatPeriod 1.3.6.1.4.1.2011.5.25.31.7.1.2
Heartbeat sending period detected in the trap reporting channel, with the minimum value of 60 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..86400  

hwHeartbeatTrapPrefix 1.3.6.1.4.1.2011.5.25.31.7.2
OBJECT IDENTIFIER    

hwEntityHeartbeatTrap 1.3.6.1.4.1.2011.5.25.31.7.2.1
Heartbeat trap.
Status: current Access: read-write
NOTIFICATION-TYPE    

hwPreDisposeObjects 1.3.6.1.4.1.2011.5.25.31.8
OBJECT IDENTIFIER    

hwPreDisposeInfo 1.3.6.1.4.1.2011.5.25.31.8.1
OBJECT IDENTIFIER    

hwPreDisposeSequenceNo 1.3.6.1.4.1.2011.5.25.31.8.1.1
This object indicates the sequence number of the 'predispose capability file'.The value consists of the file version number and CRC code.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwPreDisposedTraps 1.3.6.1.4.1.2011.5.25.31.8.2
OBJECT IDENTIFIER    

hwInsertDiffFromPreDisposed 1.3.6.1.4.1.2011.5.25.31.8.2.1
This object indicates the type of the inserted entity is different from that of pre-disposed entity on the slot.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPreDisposedChangeNotification 1.3.6.1.4.1.2011.5.25.31.8.2.2
This object indicates the change of the 'predispose capability file'. An alarm is generated if the sequence number of the 'predispose capability file' in the current startup file is different from that in the last startup file.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPreDisposeConfigTable 1.3.6.1.4.1.2011.5.25.31.8.3
Table of predisposing boards or flexible subcards.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwPreDisposeConfigEntry

hwPreDisposeConfigEntry 1.3.6.1.4.1.2011.5.25.31.8.3.1
Entry of the table to predispose boards or flexible subcards.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwPreDisposeConfigEntry  

hwDisposeSlot 1.3.6.1.4.1.2011.5.25.31.8.3.1.1
This object indicates the slot ID of predisposed board.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwDisposeCardId 1.3.6.1.4.1.2011.5.25.31.8.3.1.2
This object indicates the card ID of predisposed subcard.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwDisposeSbom 1.3.6.1.4.1.2011.5.25.31.8.3.1.3
This object indicates the sbom information of predisposed board or subcard.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwDisposeRowStatus 1.3.6.1.4.1.2011.5.25.31.8.3.1.4
This object indicates the row status when config predispose. active(1) notInService(2) notReady(3) createAndGo(4) createAndWait(5) destroy(6)
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwDisposeOperState 1.3.6.1.4.1.2011.5.25.31.8.3.1.5
The value of this object identifies the operation status. opSuccess(1): The operation succeeds. opInProgress(2): The operation is ongoing. opDevNotSupportPredispose(3): The device does not support predispose. opCardNotSupportPredispose(4): The type of card or subcard is not supported to be predisposed on this device. opAlreadyPredispose(5): The slot or subslot has already been predisposed. opCardConflict(6): The slot or subslot to be predisposed conflict with others. opDevOperationError(7): Other error occurs on the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER opSuccess(1), opInProgress(2), opDevNotSupportPredispose(3), opCardNotSupportPredispose(4), opAlreadyPredispose(5), opCardConflict(6), opDevOperationError(7)  

hwPreDisposeEntInfoTable 1.3.6.1.4.1.2011.5.25.31.8.4
This table is used to get the information of predisposed entitys.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwPreDisposeEntInfoEntry

hwPreDisposeEntInfoEntry 1.3.6.1.4.1.2011.5.25.31.8.4.1
Entry of the table to get the information of predisposed entitys.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwPreDisposeEntInfoEntry  

hwDisposeEntPhysicalIndex 1.3.6.1.4.1.2011.5.25.31.8.4.1.1
The index for this entry.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  PhysicalIndex  

hwDisposeEntPhysicalDescr 1.3.6.1.4.1.2011.5.25.31.8.4.1.2
A textual description of predisposed physical entity.This object should contain a string which identifies the manufacturer's name for the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwDisposeEntPhysicalVendorType 1.3.6.1.4.1.2011.5.25.31.8.4.1.3
An indication of the vendor-specific hardware type of the predisposed physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

hwDisposeEntPhysicalContainedIn 1.3.6.1.4.1.2011.5.25.31.8.4.1.4
The value of 'entPhysicalContainedIn' for the predisposed physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hwDisposeEntPhysicalClass 1.3.6.1.4.1.2011.5.25.31.8.4.1.5
An indication of the general hardware type of the predisposed physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalClass  

hwDisposeEntPhysicalParentRelPos 1.3.6.1.4.1.2011.5.25.31.8.4.1.6
An indication of the relative position of this 'child' component among all its 'sibling' components.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..2147483647  

hwDisposeEntPhysicalName 1.3.6.1.4.1.2011.5.25.31.8.4.1.7
The textual name of the predisposed physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hwOSPUnifyManageObjects 1.3.6.1.4.1.2011.5.25.31.9
OBJECT IDENTIFIER    

hwEntityExtOSPTrapsPrefix 1.3.6.1.4.1.2011.5.25.31.9.1
OBJECT IDENTIFIER    

hwEntityExtUnconnected 1.3.6.1.4.1.2011.5.25.31.9.1.1
Board become unconnected for some reason.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtUnconnectedResume 1.3.6.1.4.1.2011.5.25.31.9.1.2
Board resume from unconnected
Status: current Access: read-only
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor