HUAWEI-DISMAN-PING-MIB

File: HUAWEI-DISMAN-PING-MIB.mib (38875 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC DISMAN-PING-MIB
HUAWEI-MIB

Imported symbols

Counter32 Gauge32 Integer32
MODULE-IDENTITY OBJECT-TYPE mib-2
TEXTUAL-CONVENTION DateAndTime DisplayString
TimeStamp Unsigned32 RowStatus
pingCtlEntry pingCtlOwnerIndex pingCtlTestName
hwDatacomm

Defined Types

InetAddress  
Denotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. The InetAddressType object which defines the context must be registered immediately before the object which uses the InetAddress textual convention. In other words, the object identifiers for the InetAddressType object and the InetAddress object MUST have the same length and the last sub-identifier of the InetAddressType object MUST be 1 less than the last sub-identifier of the InetAddress object. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the OBJECT-TYPE declaration MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..255)  

HWPingCtlEntry  
SEQUENCE    
  hwpingCtlTargetPort Integer32
  hwpingCtlSourcePort Integer32
  hwpingCtlTTL Integer32
  hwpingCtlJitterAdminInterval Integer32
  hwpingCtlJitterAdminNumPackets Integer32
  hwpingCtlHttpOperationType INTEGER
  hwpingCtlHttpOperationString DisplayString
  hwpingCtlFtpOperationType INTEGER
  hwpingCtlFtpUsername DisplayString
  hwpingCtlFtpPassword DisplayString
  hwpingCtlFtpOperationString DisplayString
  hwpingCtlVPNInstance DisplayString

HWPingResultsEntry  
SEQUENCE    
  hwpingResultsRttNumDisconnects Gauge32
  hwpingResultsRttTimeouts Gauge32
  hwpingResultsRttBusies Gauge32
  hwpingResultsRttNoConnections Gauge32
  hwpingResultsRttDrops Gauge32
  hwpingResultsRttSequenceErrors Gauge32
  hwpingResultsRttStatsErrors Gauge32
  hwpingResultsMaxDelaySD Gauge32
  hwpingResultsMaxDelayDS Gauge32
  hwpingResultsLostPacketRatio Gauge32

HWPingJitterStatsEntry  
SEQUENCE    
  hwPingJitterStatsNumOfRTT Counter32
  hwPingJitterStatsMinOfPositivesSD Gauge32
  hwPingJitterStatsMaxOfPositivesSD Gauge32
  hwPingJitterStatsNumOfPositivesSD Gauge32
  hwPingJitterStatsSumOfPositivesSD Gauge32
  hwPingJitterStatsSum2PositivesSD Gauge32
  hwPingJitterStatsMinOfNegativesSD Gauge32
  hwPingJitterStatsMaxOfNegativesSD Gauge32
  hwPingJitterStatsNumOfNegativesSD Gauge32
  hwPingJitterStatsSumOfNegativesSD Gauge32
  hwPingJitterStatsSum2NegativesSD Gauge32
  hwPingJitterStatsMinOfPositivesDS Gauge32
  hwPingJitterStatsMaxOfPositivesDS Gauge32
  hwPingJitterStatsNumOfPositivesDS Gauge32
  hwPingJitterStatsSumOfPositivesDS Gauge32
  hwPingJitterStatsSum2PositivesDS Gauge32
  hwPingJitterStatsMinOfNegativesDS Gauge32
  hwPingJitterStatsMaxOfNegativesDS Gauge32
  hwPingJitterStatsNumOfNegativesDS Gauge32
  hwPingJitterStatsSumOfNegativesDS Gauge32
  hwPingJitterStatsSum2NegativesDS Gauge32
  hwPingJitterStatsPacketLossSD Gauge32
  hwPingJitterStatsPacketLossDS Gauge32
  hwPingJitterStatsAvePositivesSD Gauge32
  hwPingJitterStatsAveNegativesSD Gauge32
  hwPingJitterStatsAvePositivesDS Gauge32
  hwPingJitterStatsAveNegativesDS Gauge32
  hwPingJitterStatsPktLossUnknown Gauge32

HWPingTcpServerEntry  
SEQUENCE    
  hwPingTcpServerIpAddress InetAddress
  hwPingTcpServerPort Integer32
  hwpingTcpServerVPNInstance DisplayString
  hwpingTcpServerRowStatus RowStatus

HWPingUdpServerEntry  
SEQUENCE    
  hwPingUdpServerIpAddress InetAddress
  hwPingUdpServerPort Integer32
  hwpingUdpServerVPNInstance DisplayString
  hwpingUdpServerRowStatus RowStatus

Defined Values

hwDismanPing 1.3.6.1.4.1.2011.5.25.28
This private mib file includes the test information of the device. It is supplementary for DISMAN-PING-MIB(rfc2925). By setting more parameters you can finish more types test such as tcp, udp, dlsw, dhcp, ftp, http and jitter . This mib contains 5 tables: hwPingCtlTable, hwpingResultsTable, hwPingJitterStatsTable, hwPingTcpServerTable, hwPingUdpServerTable, and 3 nodes: hwPingMIBVersion, hwPingAgentEnable, hwPingServerEnable.
MODULE-IDENTITY    

hwPingObjects 1.3.6.1.4.1.2011.5.25.28.1
OBJECT IDENTIFIER    

hwPingImplementationTypeDomains 1.3.6.1.4.1.2011.5.25.28.2
OBJECT IDENTIFIER    

hwpingUdpEcho 1.3.6.1.4.1.2011.5.25.28.2.1
Indicates that an implementation is using the UDP based echo server. Notes: The hwpingCtlTargetPort and hwpingCtlSourcePort need to be set.
Status: current Access: read-write
OBJECT-IDENTITY    

hwpingTcpconnect 1.3.6.1.4.1.2011.5.25.28.2.2
Indicates that an implementation is attempting to connect to a TCP port in order to calculate a round trip time. Notes: The hwpingCtlTargetPort and hwpingCtlSourcePort need to be set.
Status: current Access: read-write
OBJECT-IDENTITY    

hwpingjitter 1.3.6.1.4.1.2011.5.25.28.2.3
Indicates that an implementation is using udp for packet transfers. 'jitter' will cause the PING application to perform delay variance analysis.
Status: current Access: read-write
OBJECT-IDENTITY    

hwpingHttp 1.3.6.1.4.1.2011.5.25.28.2.4
Indicates that an implementation is using udp for name resolution, tcp connect and tcp data transfer mechanisms for HTTP data download from a particular HTTP Server. it cause the PING application to perform a download of the object specified in the URL
Status: current Access: read-write
OBJECT-IDENTITY    

hwpingdlsw 1.3.6.1.4.1.2011.5.25.28.2.5
Indicates that an implementation is using tcp for sending keepalives. 'dlsw' will cause the PING application to perform a keepalive operation to measure the response time of a DLSw peer.
Status: current Access: read-write
OBJECT-IDENTITY    

hwpingdhcp 1.3.6.1.4.1.2011.5.25.28.2.6
Indicates that an implementation is using udp for sending dhcp requests. 'dhcp' will cause the PING application to perform an IP Address lease request/teardown operation.
Status: current Access: read-write
OBJECT-IDENTITY    

hwpingftp 1.3.6.1.4.1.2011.5.25.28.2.7
Indicates that an implementation is using tcp for connect & data transfer.
Status: current Access: read-write
OBJECT-IDENTITY    

hwPingMIBVersion 1.3.6.1.4.1.2011.5.25.28.1.1
Huawei PING MIB version string. The format will be: 'Version.Release.Patch: Textual-Description' For example: '1.0.0: Initial Ping MIB'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hwPingCtlTable 1.3.6.1.4.1.2011.5.25.28.1.2
Defines the ping Control Extend Table for providing, via SNMP, the capability of performing ping operations at a remote host.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPingCtlEntry

hwPingCtlEntry 1.3.6.1.4.1.2011.5.25.28.1.2.1
Defines an entry in the hwpingCtlTable. The operation of this table is same as that of pingResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPingCtlEntry  

hwpingCtlTargetPort 1.3.6.1.4.1.2011.5.25.28.1.2.1.1
This object represents the target's port number. This object is applicable to udpEcho, tcpConnect and jitter probes.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

hwpingCtlSourcePort 1.3.6.1.4.1.2011.5.25.28.1.2.1.2
This object represents the source's port number. If this object is not specified, the application will get a port allocated by the system. This object is applicable to all probes except dns, dlsw.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

hwpingCtlTTL 1.3.6.1.4.1.2011.5.25.28.1.2.1.3
Specifies the value to store in the TTL Field in the IP packet used to encapsulate the ping probe.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwpingCtlJitterAdminInterval 1.3.6.1.4.1.2011.5.25.28.1.2.1.4
This value represents the inter-packet delay between packets and is in milliseconds. This value is currently used for Jitter probe. This object is applicable to jitter probe only.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwpingCtlJitterAdminNumPackets 1.3.6.1.4.1.2011.5.25.28.1.2.1.5
This value represents the number of packets that need to be transmitted. This value is currently used for Jitter probe. This object is applicable to jitter probe only.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwpingCtlHttpOperationType 1.3.6.1.4.1.2011.5.25.28.1.2.1.6
Http operation type:get or post.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER get(1), post(2)  

hwpingCtlHttpOperationString 1.3.6.1.4.1.2011.5.25.28.1.2.1.7
Http operation string.for example,if you choose get operation type,the string will be url , home page and http version.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..240)  

hwpingCtlFtpOperationType 1.3.6.1.4.1.2011.5.25.28.1.2.1.8
Ftp operation type:get or put
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER get(1), put(2)  

hwpingCtlFtpUsername 1.3.6.1.4.1.2011.5.25.28.1.2.1.9
Ftp username
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

hwpingCtlFtpPassword 1.3.6.1.4.1.2011.5.25.28.1.2.1.10
Ftp password.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

hwpingCtlFtpOperationString 1.3.6.1.4.1.2011.5.25.28.1.2.1.11
Ftp operation string.If the ftp operation type is get,the string will be file name that you will get from ftp server.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..240)  

hwpingCtlVPNInstance 1.3.6.1.4.1.2011.5.25.28.1.2.1.12
This field is used to specify the VPN name in which the PING operation will be userd. The agent will use the field to identify the VPN routing Table for this operation.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

hwpingResultsTable 1.3.6.1.4.1.2011.5.25.28.1.3
Defines the Ping Results Extend Table for providing the capability of performing ping operations at a remote host. The results of these operations are stored in the hwpingResultsTable . The operation of this table is same as that of pingResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPingResultsEntry

hwpingResultsEntry 1.3.6.1.4.1.2011.5.25.28.1.3.1
The operation of this table is same as that of pingResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPingResultsEntry  

hwpingResultsRttNumDisconnects 1.3.6.1.4.1.2011.5.25.28.1.3.1.1
When the pingCtlType is 'icmpecho' , this object represents the number of times that the target or hop along the path to a target became disconnected. For all other values of pingCtlType, this object will remain zero. For connectionless protocols this has no meaning, and will consequently remain 0. Since this error does not indicate any information about the failure of an PING operation, no response time information for this instance will be recorded in the appropriate objects.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsRttTimeouts 1.3.6.1.4.1.2011.5.25.28.1.3.1.2
The number of occasions when a PING operation was not completed before a timeout occurred, i.e. pingCtlTimeOut was exceeded. Since the PING operation was never completed, the completion time of these operations are not accumulated.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsRttBusies 1.3.6.1.4.1.2011.5.25.28.1.3.1.3
The number of occasions when a PING operation could not be initiated because a previous PING operation has not been completed. When the pingCtlType is 'pathEcho' this can occur for both connection oriented protocols and connectionless protocols. When the initiation of a new operation cannot be started, this object will be incremented and the operation will be omitted. (The next operation will start at the next Frequency).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsRttNoConnections 1.3.6.1.4.1.2011.5.25.28.1.3.1.4
When the pingCtlType is 'icmpecho' this is the number of occasions when a PING operation could not be initiated because the connection to the target has not been established. For all other pingCtlTypes this object will remain zero.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsRttDrops 1.3.6.1.4.1.2011.5.25.28.1.3.1.5
The number of occasions when a PING operation could not be initiated because some necessary internal resource (for example memory) was not available,or the operation completion could not be recognized.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsRttSequenceErrors 1.3.6.1.4.1.2011.5.25.28.1.3.1.6
When the pingCtlType is 'icmpecho' this is the number of PING operation completions received with an unexpected sequence identifier. For all other values of pingCtlType this object will remain zero. When this has occurred some of the possible reasons may be: - a duplicate packet was received - a response was received after it had timed-out - a corrupted packet was received and was not detected
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsRttStatsErrors 1.3.6.1.4.1.2011.5.25.28.1.3.1.7
The number of some other errors
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsMaxDelaySD 1.3.6.1.4.1.2011.5.25.28.1.3.1.8
The maximal delay from source device to destination device. Currently this value is only used for JITTER test, and this value must be 0 in other type test. In JITTER test, if destination system time is not valid, the SD delay may be set 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsMaxDelayDS 1.3.6.1.4.1.2011.5.25.28.1.3.1.9
The maximal delay from destination device to source device. Currently this value is only used for JITTER test, and this value is 0 in other type test. In JITTER test, if destination system time is not valid, the DS delay may be set 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwpingResultsLostPacketRatio 1.3.6.1.4.1.2011.5.25.28.1.3.1.10
The value of this object reflects the drop rate of HWPing test. For example, this value is 30 that means source device only had received 70% packets of total sent packets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsTable 1.3.6.1.4.1.2011.5.25.28.1.4
A table which contains the status of latest Jitter operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPingJitterStatsEntry

hwPingJitterStatsEntry 1.3.6.1.4.1.2011.5.25.28.1.4.1
A table which contains the status of latest Jitter operation. This entry is created only if the pingCtlType is hwpingjitter.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPingJitterStatsEntry  

hwPingJitterStatsNumOfRTT 1.3.6.1.4.1.2011.5.25.28.1.4.1.1
The number of Jitter's that are successfully measured.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwPingJitterStatsMinOfPositivesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.2
The minimum of all positive jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsMaxOfPositivesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.3
The maximum of all positive jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsNumOfPositivesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.4
The sum of number of all positive jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsSumOfPositivesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.5
The sum of RTT's of all positive jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsSum2PositivesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.6
The sum of square of RTT's of all positive jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsMinOfNegativesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.7
The minimum of absolute values of all negative jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsMaxOfNegativesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.8
The maximum of absolute values of all negative jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsNumOfNegativesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.9
The sum of number of all negative jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsSumOfNegativesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.10
The sum of all negative jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsSum2NegativesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.11
The sum of square of RTT's of all negative jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsMinOfPositivesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.12
The minimum of all positive jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsMaxOfPositivesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.13
The maximum of all positive jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsNumOfPositivesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.14
The sum of number of all positive jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsSumOfPositivesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.15
The sum of RTT's of all positive jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsSum2PositivesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.16
The sum of squares of RTT's of all positive jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsMinOfNegativesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.17
The minimum of all negative jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsMaxOfNegativesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.18
The maximum of all negative jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsNumOfNegativesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.19
The sum of number of all negative jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsSumOfNegativesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.20
The sum of RTT's of all negative jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsSum2NegativesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.21
The sum of squares of RTT's of all negative jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsPacketLossSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.22
The number of packets lost when sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsPacketLossDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.23
The number of packets lost when sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsAvePositivesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.24
The average of RTT's of all positive jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsAveNegativesSD 1.3.6.1.4.1.2011.5.25.28.1.4.1.25
The average of all negative jitter values from packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsAvePositivesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.26
The average of RTT's of all positive jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsAveNegativesDS 1.3.6.1.4.1.2011.5.25.28.1.4.1.27
The average of RTT's of all negative jitter values from packets sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingJitterStatsPktLossUnknown 1.3.6.1.4.1.2011.5.25.28.1.4.1.28
The number of packets which lost but not knowing result .
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPingAgentEnable 1.3.6.1.4.1.2011.5.25.28.1.5
Enable Huawei PING agent function
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwPingTcpServerTable 1.3.6.1.4.1.2011.5.25.28.1.6
A table which contains the status of hwping tcp server configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPingTcpServerEntry

hwPingTcpServerEntry 1.3.6.1.4.1.2011.5.25.28.1.6.1
A table which contains the status of hwping tcp server configuration information. This entry is includeed not only the tcp server ip address but also the tcp server udp port. If used for VPN it is also included the VPN name.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPingTcpServerEntry  

hwPingTcpServerIpAddress 1.3.6.1.4.1.2011.5.25.28.1.6.1.1
This object represents the tcp server's ip address. This object and hwpingTcpServerPort is hwPingTcpServerTable index.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

hwPingTcpServerPort 1.3.6.1.4.1.2011.5.25.28.1.6.1.2
This object represents the tcp server's port number. This object and hwPingTcpServerIpAddress is hwPingTcpServerTable index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

hwpingTcpServerVPNInstance 1.3.6.1.4.1.2011.5.25.28.1.6.1.3
This field is used to specify the VPN name in which the PING operation will be userd. The TCP server will use the field to identify the VPN routing Table for this operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

hwpingTcpServerRowStatus 1.3.6.1.4.1.2011.5.25.28.1.6.1.4
This object allows entries to be created and deleted in the hwPingTcpServerTable. A value MUST be specified for hwPingTcpServerIpAddress and hwPingTcpServerPort prior to a transition to active(1) state being accepted.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwPingUdpServerTable 1.3.6.1.4.1.2011.5.25.28.1.7
A table which contains the status of hwping udp server configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPingUdpServerEntry

hwPingUdpServerEntry 1.3.6.1.4.1.2011.5.25.28.1.7.1
A table which contains the status of hwping udp server configuration information. This entry is includeed not only the udp server ip address but also the udp server udp port.If used for VPN it is also included the VPN name.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPingUdpServerEntry  

hwPingUdpServerIpAddress 1.3.6.1.4.1.2011.5.25.28.1.7.1.1
This object represents the udp server's ip address. This object and hwpingUdpServerPort is hwPingUdpServerEntry index.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

hwPingUdpServerPort 1.3.6.1.4.1.2011.5.25.28.1.7.1.2
This object represents the udp server's port number. This object and hwPingUdpServerIpAddress is hwPingUdpServerEntry index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

hwpingUdpServerVPNInstance 1.3.6.1.4.1.2011.5.25.28.1.7.1.3
This field is used to specify the VPN name in which the PING operation will be userd. The UDP server will use the field to identify the VPN routing Table for this operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

hwpingUdpServerRowStatus 1.3.6.1.4.1.2011.5.25.28.1.7.1.4
This object allows entries to be created and deleted in the hwPingUdpServerTable. A value MUST be specified for hwPingUdpServerIpAddress and hwPingUdpServerPort prior to a transition to active(1) state being accepted.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwPingServerEnable 1.3.6.1.4.1.2011.5.25.28.1.8
Enable Huawei PING server function
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)