HUAWEI-DC-TRAP-MIB

File: HUAWEI-DC-TRAP-MIB.mib (38912 bytes)

Imported modules

ENTITY-MIB HUAWEI-MIB RFC1213-MIB
SNMPv2-TC SNMPv2-CONF SNMPv2-SMI

Imported symbols

entPhysicalName hwDatacomm ifIndex
ifDescr DisplayString OBJECT-GROUP
MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-TYPE
MODULE-IDENTITY NOTIFICATION-TYPE Integer32

Defined Values

hwDCTrapMIB 1.3.6.1.4.1.2011.5.25.37
The HUAWEI-DC-TRAP-MIB provides information about DataComm TRAPS.
MODULE-IDENTITY    

hwDCTrapControl 1.3.6.1.4.1.2011.5.25.37.1
OBJECT IDENTIFIER    

hwDCCtrlTrap 1.3.6.1.4.1.2011.5.25.37.1.1
A string serving as a bit map for the trap events defined by the hwDatacomm traps. This object is used to enable and disable specific hwDatacomm traps where a 1 in the bit field represents enabled. The right-most bit (least significant) represents trap 0.
OBJECT-TYPE    
  OCTET STRING Size(32)  

hwTunnelGroupID 1.3.6.1.4.1.2011.5.25.37.1.2
Tunnel id
OBJECT-TYPE    
  Integer32 0..2047  

hwDCTrapReason 1.3.6.1.4.1.2011.5.25.37.1.3
For the BTB system to report Trap Reason.
OBJECT-TYPE    
  DisplayString  

hwDCTraps 1.3.6.1.4.1.2011.5.25.37.2
OBJECT IDENTIFIER    

hwMPUSynClkFaulty 1.3.6.1.4.1.2011.5.25.37.2.1
MPU sync clock signal faulty!
NOTIFICATION-TYPE    

hwMPUSynClkFaultyResume 1.3.6.1.4.1.2011.5.25.37.2.2
MPU sync clock signal faulty resume!
NOTIFICATION-TYPE    

hwSlaveMPUNoResp 1.3.6.1.4.1.2011.5.25.37.2.3
Slave MPU has no response!
NOTIFICATION-TYPE    

hwSlaveMPUNoRespResume 1.3.6.1.4.1.2011.5.25.37.2.4
Slave MPU has no response resume!
NOTIFICATION-TYPE    

hwBrdChannelFaulty 1.3.6.1.4.1.2011.5.25.37.2.5
Board channel faulty!
NOTIFICATION-TYPE    

hwBrdChannelFaultyResume 1.3.6.1.4.1.2011.5.25.37.2.6
Board channel faulty resume!
NOTIFICATION-TYPE    

hwBrdNofullin 1.3.6.1.4.1.2011.5.25.37.2.7
Board not full in!
NOTIFICATION-TYPE    

hwBrdNofullinResume 1.3.6.1.4.1.2011.5.25.37.2.8
Board not full in resume!
NOTIFICATION-TYPE    

hwBrdTypeNoMatchReset 1.3.6.1.4.1.2011.5.25.37.2.9
Board is reset because of the chip type is not matching!
NOTIFICATION-TYPE    

hwBrdAutoSwtFail 1.3.6.1.4.1.2011.5.25.37.2.10
Board automatically switch syn-clock but it locked failed!
NOTIFICATION-TYPE    

hwBrdAutoSwt 1.3.6.1.4.1.2011.5.25.37.2.11
Board automatically switch syn-clock!
NOTIFICATION-TYPE    

hwBrdClkLockERR 1.3.6.1.4.1.2011.5.25.37.2.12
Board fabric clock is unlocked!
NOTIFICATION-TYPE    

hwBrdClkLockERRResume 1.3.6.1.4.1.2011.5.25.37.2.13
Board fabric clock unlock to current clock resume!
NOTIFICATION-TYPE    

hwBrdRemoved 1.3.6.1.4.1.2011.5.25.37.2.14
Board pulled out!
NOTIFICATION-TYPE    

hwBrdInserted 1.3.6.1.4.1.2011.5.25.37.2.15
Board plugged in!
NOTIFICATION-TYPE    

hwBrdUp 1.3.6.1.4.1.2011.5.25.37.2.16
Board register!
NOTIFICATION-TYPE    

hwClkSrcMiss 1.3.6.1.4.1.2011.5.25.37.2.17
CLK source Loss Of Signal!
NOTIFICATION-TYPE    

hwClkAllSrcLost 1.3.6.1.4.1.2011.5.25.37.2.18
CLK all source lost!
NOTIFICATION-TYPE    

hwClkAllSrcLostResume 1.3.6.1.4.1.2011.5.25.37.2.19
CLK all source lost resume!
NOTIFICATION-TYPE    

hwClkFail 1.3.6.1.4.1.2011.5.25.37.2.20
CLK hardware failed!
NOTIFICATION-TYPE    

hwClkFailResume 1.3.6.1.4.1.2011.5.25.37.2.21
CLK hardware failed resume!
NOTIFICATION-TYPE    

hwClkNoHeartbeat 1.3.6.1.4.1.2011.5.25.37.2.22
CLK No Heartbeat!
NOTIFICATION-TYPE    

hwClkNoHeartbeatResume 1.3.6.1.4.1.2011.5.25.37.2.23
CLK No Heartbeat resume!
NOTIFICATION-TYPE    

hwLPULostSynAlarm 1.3.6.1.4.1.2011.5.25.37.2.24
LPU SERDES interface is lost synchronization!
NOTIFICATION-TYPE    

hwLPUOpenChannelError 1.3.6.1.4.1.2011.5.25.37.2.25
LPU SERDES interface open error!
NOTIFICATION-TYPE    

hwLPUSlfTstErr 1.3.6.1.4.1.2011.5.25.37.2.26
LPU self test error!
NOTIFICATION-TYPE    

hwLPU3ClkSwitch 1.3.6.1.4.1.2011.5.25.37.2.27
LPU 3 class clock is switch!
NOTIFICATION-TYPE    

hwSFULostHrtReset 1.3.6.1.4.1.2011.5.25.37.2.28
SFU is reset because of heart beat loss!
NOTIFICATION-TYPE    

hwSFULinkLostReset 1.3.6.1.4.1.2011.5.25.37.2.29
SFU is reset because of SERDES interface input channel link lost numbers over threshold!
NOTIFICATION-TYPE    

hwSFUChannelLinkLost 1.3.6.1.4.1.2011.5.25.37.2.30
SFU check SERDES interface input channel link lost!
NOTIFICATION-TYPE    

hwSFUInChannelOpenFail 1.3.6.1.4.1.2011.5.25.37.2.31
SFU SERDES interface input channel is opened failed!
NOTIFICATION-TYPE    

hwVoltSensorFail 1.3.6.1.4.1.2011.5.25.37.2.32
Board voltage monitor failure!
NOTIFICATION-TYPE    

hwVoltSensorFailResume 1.3.6.1.4.1.2011.5.25.37.2.33
Board voltage monitor failure resume!
NOTIFICATION-TYPE    

hwVoltBtmC 1.3.6.1.4.1.2011.5.25.37.2.34
Board voltage below fatal threshold!
NOTIFICATION-TYPE    

hwVoltBtmCResume 1.3.6.1.4.1.2011.5.25.37.2.35
Board voltage below fatal threshold resume!
NOTIFICATION-TYPE    

hwVoltSprC 1.3.6.1.4.1.2011.5.25.37.2.36
Board voltage over fatal threshold!
NOTIFICATION-TYPE    

hwVoltSprCResume 1.3.6.1.4.1.2011.5.25.37.2.37
Board voltage over fatal threshold resume!
NOTIFICATION-TYPE    

hwVoltBtmM 1.3.6.1.4.1.2011.5.25.37.2.38
Board voltage below major threshold!
NOTIFICATION-TYPE    

hwVoltBtmMResume 1.3.6.1.4.1.2011.5.25.37.2.39
Board voltage below major threshold resume!
NOTIFICATION-TYPE    

hwVoltSprM 1.3.6.1.4.1.2011.5.25.37.2.40
Board voltage over major threshold!
NOTIFICATION-TYPE    

hwVoltSprMResume 1.3.6.1.4.1.2011.5.25.37.2.41
Board voltage over major threshold resume!
NOTIFICATION-TYPE    

hwTempSensorFail 1.3.6.1.4.1.2011.5.25.37.2.42
Board temprature monitor failure!
NOTIFICATION-TYPE    

hwTempSensorFailResume 1.3.6.1.4.1.2011.5.25.37.2.43
Board temperature monitor failure resume!
NOTIFICATION-TYPE    

hwTempMnr 1.3.6.1.4.1.2011.5.25.37.2.44
Board temperature over minor threshold!
NOTIFICATION-TYPE    

hwTempMnrResume 1.3.6.1.4.1.2011.5.25.37.2.45
Board temperature over minor threshold resume!
NOTIFICATION-TYPE    

hwTempMjr 1.3.6.1.4.1.2011.5.25.37.2.46
Board temperature over major threshold!
NOTIFICATION-TYPE    

hwTempMjrResume 1.3.6.1.4.1.2011.5.25.37.2.47
Board temperature over major threshold resume!
NOTIFICATION-TYPE    

hwTempCtl 1.3.6.1.4.1.2011.5.25.37.2.48
Board temperature over fatal threshold!
NOTIFICATION-TYPE    

hwTempCtlResume 1.3.6.1.4.1.2011.5.25.37.2.49
Board temperature over fatal threshold resume!
NOTIFICATION-TYPE    

hwFanHFail 1.3.6.1.4.1.2011.5.25.37.2.50
Fan hardware failure!
NOTIFICATION-TYPE    

hwFanFail 1.3.6.1.4.1.2011.5.25.37.2.51
Fan failure!
NOTIFICATION-TYPE    

hwFanFailResume 1.3.6.1.4.1.2011.5.25.37.2.52
Fan failure resume!
NOTIFICATION-TYPE    

hwFanAbsent 1.3.6.1.4.1.2011.5.25.37.2.53
Fan absent!
NOTIFICATION-TYPE    

hwFanAbsentResume 1.3.6.1.4.1.2011.5.25.37.2.54
Fan absent resume!
NOTIFICATION-TYPE    

hwFanCabUN 1.3.6.1.4.1.2011.5.25.37.2.55
Fan cable unplugged!
NOTIFICATION-TYPE    

hwFanCabUNResume 1.3.6.1.4.1.2011.5.25.37.2.56
Fan cable unplugged resume!
NOTIFICATION-TYPE    

hwPwrFail 1.3.6.1.4.1.2011.5.25.37.2.57
Power failure!
NOTIFICATION-TYPE    

hwPwrFailResume 1.3.6.1.4.1.2011.5.25.37.2.58
Power failure resume!
NOTIFICATION-TYPE    

hwPwrAbsent 1.3.6.1.4.1.2011.5.25.37.2.59
Power absent!
NOTIFICATION-TYPE    

hwPwrAbsentResume 1.3.6.1.4.1.2011.5.25.37.2.60
Power absent resume!
NOTIFICATION-TYPE    

hwPwrCabUN 1.3.6.1.4.1.2011.5.25.37.2.61
Power monitor cable unplugged!
NOTIFICATION-TYPE    

hwPwrCabUNResume 1.3.6.1.4.1.2011.5.25.37.2.62
Power monitor cable unplugged resume!
NOTIFICATION-TYPE    

hwLCDHFail 1.3.6.1.4.1.2011.5.25.37.2.63
LCD hardware failure!
NOTIFICATION-TYPE    

hwLCDFail 1.3.6.1.4.1.2011.5.25.37.2.64
LCD failure!
NOTIFICATION-TYPE    

hwLCDAbsent 1.3.6.1.4.1.2011.5.25.37.2.65
LCD absent!
NOTIFICATION-TYPE    

hwLCDAbsentResume 1.3.6.1.4.1.2011.5.25.37.2.66
LCD absent resume!
NOTIFICATION-TYPE    

hwLCDCabUN 1.3.6.1.4.1.2011.5.25.37.2.67
LCD cable unplugged!
NOTIFICATION-TYPE    

hwLCDCabUNResume 1.3.6.1.4.1.2011.5.25.37.2.68
LCD cable unplugged resume!
NOTIFICATION-TYPE    

hwROMFail 1.3.6.1.4.1.2011.5.25.37.2.69
EEPROM failure!
NOTIFICATION-TYPE    

hwMonitorBUSFail 1.3.6.1.4.1.2011.5.25.37.2.70
MonitorBUS failure!
NOTIFICATION-TYPE    

hwMonitorBUSFailResume 1.3.6.1.4.1.2011.5.25.37.2.71
MonitorBUS failure resume!
NOTIFICATION-TYPE    

hwBoardOfflineChange 1.3.6.1.4.1.2011.5.25.37.2.72
Board power status change!
NOTIFICATION-TYPE    

hwWriteFlashError 1.3.6.1.4.1.2011.5.25.37.2.100
write flash error!
NOTIFICATION-TYPE    

hwBoardReset 1.3.6.1.4.1.2011.5.25.37.2.101
board reset!
NOTIFICATION-TYPE    

hwBoardResetSuccess 1.3.6.1.4.1.2011.5.25.37.2.102
board reset success!
NOTIFICATION-TYPE    

hwSlaveMPUReset 1.3.6.1.4.1.2011.5.25.37.2.103
slave MPU reset !
NOTIFICATION-TYPE    

hwMasterSlaveSwap 1.3.6.1.4.1.2011.5.25.37.2.104
master slave swap!
NOTIFICATION-TYPE    

hwRTCFail 1.3.6.1.4.1.2011.5.25.37.2.105
RTC failure!
NOTIFICATION-TYPE    

hwExchangeChipFail 1.3.6.1.4.1.2011.5.25.37.2.106
5695 exchange chip fail!
NOTIFICATION-TYPE    

hwTempResume 1.3.6.1.4.1.2011.5.25.37.2.107
Board temprature over threshold resume!
NOTIFICATION-TYPE    

hwOpticalModuleInsert 1.3.6.1.4.1.2011.5.25.37.2.108
optical module plug in !
NOTIFICATION-TYPE    

hwOpticalModuleRemove 1.3.6.1.4.1.2011.5.25.37.2.109
optical module plug out !
NOTIFICATION-TYPE    

hwFPGAAbnormal 1.3.6.1.4.1.2011.5.25.37.2.110
FPGA abnormal !
NOTIFICATION-TYPE    

hwMinMTunnelDownAlarm 1.3.6.1.4.1.2011.5.25.37.2.111
For Mac in Mac tunnel. Mac tunnel have two status: up or down, when physical interface is down or some cc package can't arrive to the other side of mac in mac tunnel, the status of tunnel will be down 1 Notice/Trap name: Tunnel down 2 Notice/Trap generation cause: when All mac tunnel have been down in the mac tunnel group 3 Repair suggestions: make one of the mac tunnel up in the mac tunnel group
NOTIFICATION-TYPE    

hwMinMTunnelUpAlarm 1.3.6.1.4.1.2011.5.25.37.2.112
For Mac in Mac tunnel. Mac tunnel have two status: up or down, if cc package can arrive to the other side of mac in mac tunnel, the status of tunnel will be up 1 Notice/Trap name: Tunnel up 2 Notice/Trap generation cause: one of the tunnel is up in the mac tunnel group 3 Repair suggestion:
NOTIFICATION-TYPE    

hwInterfacePhysicalDown 1.3.6.1.4.1.2011.5.25.37.2.113
This trap is to indicate port link down on physical layer.
NOTIFICATION-TYPE    

hwInterfacePhysicalUp 1.3.6.1.4.1.2011.5.25.37.2.114
This trap is to indicate port link up on physical layer.
NOTIFICATION-TYPE    

hwBTBStartupFileNameDifferent 1.3.6.1.4.1.2011.5.25.37.2.119
In the BTB system ,the start-up file name of master and slave chassis is different . Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBChassisRunningModeConflict 1.3.6.1.4.1.2011.5.25.37.2.120
The Master and Slave chassises running modes conflict.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBCtrlChannelFail 1.3.6.1.4.1.2011.5.25.37.2.121
The FE control channel failture, as physical link from up to down or channel blocked. Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBCtrlChannelFailResume 1.3.6.1.4.1.2011.5.25.37.2.122
The FE control channel failture resume.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBDataChannelFail 1.3.6.1.4.1.2011.5.25.37.2.123
The data channel failture, all optical links down between chassises.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBDataChannelFailResume 1.3.6.1.4.1.2011.5.25.37.2.124
The data channel failture resume.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBClkChannelFail 1.3.6.1.4.1.2011.5.25.37.2.125
The clock channel failture, clock link down between chassises.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBClkChannelFailResume 1.3.6.1.4.1.2011.5.25.37.2.126
The clock Channel failture resume.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBSFUOpticInterfaceError 1.3.6.1.4.1.2011.5.25.37.2.127
The optical fiber connection error, the connection of SFU fiber between chassises is not correct. Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBSFUOpticInterfaceErrorResume 1.3.6.1.4.1.2011.5.25.37.2.128
The optical fiber connection error resume.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBVSRInterfaceInvalid 1.3.6.1.4.1.2011.5.25.37.2.129
The SFU VSR(very short reach) interface invalid.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBVSRInterfaceInvalidResume 1.3.6.1.4.1.2011.5.25.37.2.130
The SFU VSR(very short reach) interface invalid resume.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBSlaveChassisNoHeart 1.3.6.1.4.1.2011.5.25.37.2.131
The slave chassis no heart.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBNoSlaveChassis 1.3.6.1.4.1.2011.5.25.37.2.132
No slave chassis connected to the master chassis in the BTB system.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBSlaveChassisRegisted 1.3.6.1.4.1.2011.5.25.37.2.133
The slave chassis registe successful.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBSlaveChassisRegisteFail 1.3.6.1.4.1.2011.5.25.37.2.134
The slave chassis registe failed.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwBTBChassisTypeConflict 1.3.6.1.4.1.2011.5.25.37.2.135
The chassis information conflict in the PAF and Nvram.Used for BTB or its extend system.
NOTIFICATION-TYPE    

hwSuperChangeSuccesful 1.3.6.1.4.1.2011.5.25.37.2.136
Super change successful.
NOTIFICATION-TYPE    

hwSuperChangeFailure 1.3.6.1.4.1.2011.5.25.37.2.137
Super change Failure.
NOTIFICATION-TYPE    

hwOpticaPowerAbnormal 1.3.6.1.4.1.2011.5.25.37.2.138
Optical Transceiver power abnormal.
NOTIFICATION-TYPE    

hwEpldAbnormal 1.3.6.1.4.1.2011.5.25.37.2.139
Epld logic abnormal.
NOTIFICATION-TYPE    

hwPhyChipAbnormal 1.3.6.1.4.1.2011.5.25.37.2.140
PHY chip is abnormal.
NOTIFICATION-TYPE    

hwSerdesAbnormal 1.3.6.1.4.1.2011.5.25.37.2.141
Serdes interface of PHY chip abnormal.
NOTIFICATION-TYPE    

hwBoardAbnormal 1.3.6.1.4.1.2011.5.25.37.2.142
Board is abnormal.
NOTIFICATION-TYPE    

hwFeChannelAbnormal 1.3.6.1.4.1.2011.5.25.37.2.143
FE data channel is abnormal
NOTIFICATION-TYPE    

hwParityCheckAbnormal 1.3.6.1.4.1.2011.5.25.37.2.144
Data parity check is abnormal
NOTIFICATION-TYPE    

hwPhyClockAbnormal 1.3.6.1.4.1.2011.5.25.37.2.145
The clock of PHY chip is abnormal.
NOTIFICATION-TYPE    

hwPortAutoNegotiateFail 1.3.6.1.4.1.2011.5.25.37.2.146
The ethernet port negotiate failed
NOTIFICATION-TYPE    

hwPortSemiduplex 1.3.6.1.4.1.2011.5.25.37.2.147
The ethernet port work at semi duplex state.
NOTIFICATION-TYPE    

hwScuStartModeSetFail 1.3.6.1.4.1.2011.5.25.37.2.148
The start mode of SCU set failed
NOTIFICATION-TYPE    

hwMemoryExhaust 1.3.6.1.4.1.2011.5.25.37.2.149
MPU memory exhaust.
NOTIFICATION-TYPE    

hwMemoryExhaustClear 1.3.6.1.4.1.2011.5.25.37.2.150
MPU memory usage resume to normal.
NOTIFICATION-TYPE    

hwMethAbnormal 1.3.6.1.4.1.2011.5.25.37.2.151
The Meth interface is abnormal.
NOTIFICATION-TYPE    

hwLpuNotTight 1.3.6.1.4.1.2011.5.25.37.2.152
The LPU board is not tightly installed. Install the board again.
NOTIFICATION-TYPE    

hwLicenseFail 1.3.6.1.4.1.2011.5.25.37.2.153
License fail.
NOTIFICATION-TYPE    

hwHaBatchBegin 1.3.6.1.4.1.2011.5.25.37.2.154
No command line can be entered because batch backup is processing.
NOTIFICATION-TYPE    

hwHaBatchEnd 1.3.6.1.4.1.2011.5.25.37.2.155
Command lines can be entered because batch backup ends.
NOTIFICATION-TYPE    

hwHaSmoothBegin 1.3.6.1.4.1.2011.5.25.37.2.156
No command line can be entered because data smooth is processing.
NOTIFICATION-TYPE    

hwHaSmoothEnd 1.3.6.1.4.1.2011.5.25.37.2.157
Command lines can be entered because data smooth ends.
NOTIFICATION-TYPE    

hwFanUp 1.3.6.1.4.1.2011.5.25.37.2.158
Fan register!
NOTIFICATION-TYPE    

hwDCTrapConformance 1.3.6.1.4.1.2011.5.25.37.3
OBJECT IDENTIFIER    

hwDCTrapGroups 1.3.6.1.4.1.2011.5.25.37.3.1
OBJECT IDENTIFIER    

hwDCTrapControlGroup 1.3.6.1.4.1.2011.5.25.37.3.1.1
These objects are required to control traps from hwDatacomm Traps systems.
OBJECT-GROUP    

hwDCNotificationGroup 1.3.6.1.4.1.2011.5.25.37.3.1.2
The notification group defined for Datacomm products.
NOTIFICATION-GROUP    

hwDCTrapCompliances 1.3.6.1.4.1.2011.5.25.37.3.2
OBJECT IDENTIFIER    

hwDCTrapCompliance 1.3.6.1.4.1.2011.5.25.37.3.2.1
The compliance statement.
MODULE-COMPLIANCE