HPN-ICF-TUNNEL-MIB

File: HPN-ICF-TUNNEL-MIB.mib (38397 bytes)

Imported modules

HPN-ICF-OID-MIB SNMPv2-SMI SNMPv2-TC
INET-ADDRESS-MIB IPV6-FLOW-LABEL-MIB IF-MIB

Imported symbols

hpnicfCommon MODULE-IDENTITY OBJECT-TYPE
Integer32 Unsigned32 RowStatus
TruthValue TEXTUAL-CONVENTION InetAddressType
InetAddress IPv6FlowLabelOrAny ifIndex
InterfaceIndexOrZero InterfaceIndex

Defined Types

HpnicfTunnelType  
Tunnel type definition.
TEXTUAL-CONVENTION    
  INTEGER other(1), direct(2), gre(3), minimal(4), l2tp(5), pptp(6), l2f(7), udp(8), atmp(9), msdp(10), sixToFour(11), sixOverFour(12), isatap(13), teredo(14), tunnelModeReserve(35), tunnelModeIPv4Gre(36), tunnelModeIPv6Gre(37), tunnelModeIPv4IPv4(38), tunnelModeIPv4IPv6Config(39), tunnelModeIPv4IPv6Auto(40), tunnelModeIPv4IPv66to4(41), tunnelModeIPv4IPv6Isatap(42), tunnelModeIPv6IPv4(43), tunnelModeIPv6IPv6(44), tunnelModeIPv4UdpDVPN(45), tunnelModeIPv4GreDVPN(46), tunnelModeIPv6UdpDVPN(47), tunnelModeIPv6GreDVPN(48), tunnelModeCrLsp(49), tunnelModeMax(50), tunnelModeIPv4UdpVxlan(51), tunnelModeIPv6UdpVxlan(52), tunnelModeIPv4NVGRE(53), tunnelModeIPv6NVGRE(54)  

HpnicfTunnelIfEntry  
SEQUENCE    
  hpnicfTunnelIfEncapsMethod HpnicfTunnelType
  hpnicfTunnelIfHopLimit Integer32
  hpnicfTunnelIfSecurity INTEGER
  hpnicfTunnelIfTOS Integer32
  hpnicfTunnelIfFlowLabel IPv6FlowLabelOrAny
  hpnicfTunnelIfAddressType InetAddressType
  hpnicfTunnelIfLocalInetAddress InetAddress
  hpnicfTunnelIfRemoteInetAddress InetAddress
  hpnicfTunnelIfEncapsLimit Integer32

HpnicfTunnelInetConfigEntry  
SEQUENCE    
  hpnicfTunnelInetConfigSlot Integer32
  hpnicfTunnelInetConfigSubSlot Integer32
  hpnicfTunnelInetConfigTunnNum Integer32
  hpnicfTunnelInetConfigIfIndex InterfaceIndexOrZero
  hpnicfTunnelInetConfigStatus RowStatus

HpnicfTunnelEviEntry  
SEQUENCE    
  hpnicfTunnelEviTunnNum Integer32
  hpnicfTunnelEviIfIndex InterfaceIndex
  hpnicfTunnelEviStatus RowStatus
  hpnicfTunnelEviAddressType InetAddressType
  hpnicfTunnelEviLocalAddr InetAddress
  hpnicfTunnelEviNetworkID Integer32
  hpnicfTunnelEviKeepaliveInterval Integer32
  hpnicfTunnelEviKeepaliveTimes Integer32

HpnicfTunnelEviLinkEntry  
SEQUENCE    
  hpnicfTunnelEviLinkNum Integer32
  hpnicfTunnelEviLinkIfIndex InterfaceIndex
  hpnicfTunnelEviLinkAddressType InetAddressType
  hpnicfTunnelEviLinkRemoteAddr InetAddress

HpnicfTunnelGreEntry  
SEQUENCE    
  hpnicfTunnelGreTunnNum Integer32
  hpnicfTunnelGreTunnIfIndex InterfaceIndex
  hpnicfTunnelGreAddressType InetAddressType
  hpnicfTunnelGreLocalAddr InetAddress
  hpnicfTunnelGreRemoteAddr InetAddress
  hpnicfTunnelGreKeepaliveEnabled TruthValue
  hpnicfTunnelGreKeepaliveInterval Integer32
  hpnicfTunnelGreKeepaliveTimes Integer32
  hpnicfTunnelGreSlbgGroupNum Unsigned32
  hpnicfTunnelGreTunnStatus RowStatus

HpnicfTunnelVxlanIfEntry  
SEQUENCE    
  hpnicfTunnelVxlanIfTunnNum Integer32
  hpnicfTunnelVxlanTunnIfIndex InterfaceIndex
  hpnicfTunnelVxlanIfAddressType InetAddressType
  hpnicfTunnelVxlanIfLocalAddr InetAddress
  hpnicfTunnelVxlanIfRemoteAddr InetAddress
  hpnicfTunnelVxlanIfStatus RowStatus

HpnicfTunnelTotalNumEntry  
SEQUENCE    
  hpnicfTunnelEncapsMethod HpnicfTunnelType
  hpnicfTunnelTotalNum Unsigned32

HpnicfTunnelNvgreIfEntry  
SEQUENCE    
  hpnicfTunnelNvgreIfTunnNum Integer32
  hpnicfTunnelNvgreTunnIfIndex InterfaceIndex
  hpnicfTunnelNvgreIfAddressType InetAddressType
  hpnicfTunnelNvgreIfLocalAddr InetAddress
  hpnicfTunnelNvgreIfRemoteAddr InetAddress
  hpnicfTunnelNvgreIfStatus RowStatus

Defined Values

hpnicfTunnel 1.3.6.1.4.1.11.2.14.11.15.2.53
This MIB contains objects to Manage configuration and Monitor tunnel.
MODULE-IDENTITY    

hpnicfTunnelMIBObjects 1.3.6.1.4.1.11.2.14.11.15.2.53.1
OBJECT IDENTIFIER    

hpnicfTunnelTables 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1
OBJECT IDENTIFIER    

hpnicfTunnelIfTable 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1
The (conceptual) table containing information on configured tunnels.
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfTunnelIfEntry

hpnicfTunnelIfEntry 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1
An entry (conceptual row) containing the information on a particular configured tunnel.
OBJECT-TYPE    
  HpnicfTunnelIfEntry  

hpnicfTunnelIfEncapsMethod 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.3
The encapsulation method used by the tunnel.
OBJECT-TYPE    
  HpnicfTunnelType  

hpnicfTunnelIfHopLimit 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.4
The IPv4 TTL or IPv6 Hop Limit to use in the outer IP header. A value of 0 indicates that the value is copied from the payload's header.
OBJECT-TYPE    
  Integer32 0 | 1..255  

hpnicfTunnelIfSecurity 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.5
The method used by the tunnel to secure the outer IP header. The value ipsec indicates that IPsec is used between the tunnel endpoints for authentication or encryption or both. More specific security-related information may be available in a MIB module for the security protocol in use.
OBJECT-TYPE    
  INTEGER none(1), ipsec(2), other(3)  

hpnicfTunnelIfTOS 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.6
The method used to set the high 6 bits (the differentiated services codepoint) of the IPv4 TOS or IPv6 Traffic Class in the outer IP header. A value of -1 indicates that the bits are copied from the payload's header. A value of -2 indicates that a traffic conditioner is invoked and more information may be available in a traffic conditioner MIB module. A value between 0 and 63 inclusive indicates that the bit field is set to the indicated value.
OBJECT-TYPE    
  Integer32 -2..63  

hpnicfTunnelIfFlowLabel 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.7
The method used to set the IPv6 Flow Label value. This object need not be present in rows where hpnicfTunnelIfAddressType indicates the tunnel is not over IPv6. A value of -1 indicates that a traffic conditioner is invoked and more information may be available in a traffic conditioner MIB. Any other value indicates that the Flow Label field is set to the indicated value.
OBJECT-TYPE    
  IPv6FlowLabelOrAny  

hpnicfTunnelIfAddressType 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.8
The type of address in the corresponding hpnicfTunnelIfLocalInetAddress and hpnicfTunnelIfRemoteInetAddress objects.
OBJECT-TYPE    
  InetAddressType  

hpnicfTunnelIfLocalInetAddress 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.9
The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header). If the address is unknown, the value is 0.0.0.0 for IPv4 or :: for IPv6. The type of this object is given by hpnicfTunnelIfAddressType.
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelIfRemoteInetAddress 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.10
The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header). If the address is unknown or the tunnel is not a point-to-point link (e.g., if it is a 6to4 tunnel), the value is 0.0.0.0 for tunnels over IPv4 or :: for tunnels over IPv6. The type of this object is given by hpnicfTunnelIfAddressType.
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelIfEncapsLimit 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.1.1.11
The maximum number of additional encapsulations permitted for packets undergoing encapsulation at this node. A value of -1 indicates that no limit is present (except as a result of the packet size).
OBJECT-TYPE    
  Integer32 -1 | 0..255  

hpnicfTunnelInetConfigTable 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.3
The (conceptual) table containing information on configured tunnels. This table can be used to map a set of tunnel endpoints to the associated ifIndex value. It can also be used for row creation. Note that every row in the hpnicfTunnelIfTable with a fixed destination address should have a corresponding row in the hpnicfTunnelInetConfigTable, regardless of whether it was created via SNMP.
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfTunnelInetConfigEntry

hpnicfTunnelInetConfigEntry 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.3.1
An entry (conceptual row) containing the information on a particular configured tunnel.
OBJECT-TYPE    
  HpnicfTunnelInetConfigEntry  

hpnicfTunnelInetConfigSlot 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.3.1.1
Slot number. hpnicfTunnelInetConfigSlot, hpnicfTunnelInetConfigSubSlot and hpnicfTunnelInetConfigTunnNum describe a tunnel interface. For Example, interface tunnel 0/0/25 would be configured as: hpnicfTunnelInetConfigSlot 0 hpnicfTunnelInetConfigSubSlot 0 hpnicfTunnelInetConfigTunnNum 25
OBJECT-TYPE    
  Integer32 0..255  

hpnicfTunnelInetConfigSubSlot 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.3.1.2
Sub slot number. As described in hpnicfTunnelInetConfigSlot's description.
OBJECT-TYPE    
  Integer32 0..255  

hpnicfTunnelInetConfigTunnNum 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.3.1.3
Tunnel number. As described in hpnicfTunnelInetConfigSlot's description.
OBJECT-TYPE    
  Integer32 0..65535  

hpnicfTunnelInetConfigIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.3.1.6
If the value of hpnicfTunnelInetConfigStatus for this row is active, then this object contains the value of ifIndex corresponding to the tunnel interface. A value of 0 is not legal in the active state, and means that the interface index has not yet been assigned.
OBJECT-TYPE    
  InterfaceIndexOrZero  

hpnicfTunnelInetConfigStatus 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.3.1.7
The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hpnicfTunnelIfTable may be modified while this row is active. To create a row in this table, the management station should set hpnicfTunnelInetConfigSlot, hpnicfTunnelInetConfigSubSlot, hpnicfTunnelInetConfigTunnNum, and set hpnicfTunnelInetConfigStatus to createAndGo. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable and the hpnicfTunnelIfTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable and in the hpnicfTunnelIfTable.
OBJECT-TYPE    
  RowStatus  

hpnicfTunnelEviTable 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4
The (conceptual) table containing information on configured EVI-Tunnel.
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfTunnelEviEntry

hpnicfTunnelEviEntry 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1
An entry (conceptual row) containing the information on a particular configured EVI-Tunnel.
OBJECT-TYPE    
  HpnicfTunnelEviEntry  

hpnicfTunnelEviTunnNum 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1.1
Tunnel number. An identifier used to distinguish between multiple tunnels.
OBJECT-TYPE    
  Integer32 1..2147483647  

hpnicfTunnelEviIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1.2
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  InterfaceIndex  

hpnicfTunnelEviStatus 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1.3
The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hpnicfTunnelEviTable may be modified while this row is active. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable.
OBJECT-TYPE    
  RowStatus  

hpnicfTunnelEviAddressType 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1.4
The type of address in the corresponding hpnicfTunnelEviLocalAddr objects. Can not be modified after creation.
OBJECT-TYPE    
  InetAddressType  

hpnicfTunnelEviLocalAddr 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1.5
The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header). The type of this object is given by hpnicfTunnelEviAddressType.
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelEviNetworkID 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1.6
The method used to assign a network ID to an EVI-Tunnel interface. Assign the same network ID to the EVI-Tunnel interfaces of all edge devices in an EVI network. A value of 0 indicates that no network ID is assigned to any EVI-Tunnel interface.
OBJECT-TYPE    
  Integer32 0..16777215  

hpnicfTunnelEviKeepaliveInterval 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1.7
The method used to assign the keepalive interval.
OBJECT-TYPE    
  Integer32 1..32767  

hpnicfTunnelEviKeepaliveTimes 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.4.1.8
The method used to assign the keepalive maximum number of consecutive keepalive failures that are allowed.
OBJECT-TYPE    
  Integer32 1..255  

hpnicfTunnelEviLinkTable 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.5
The (conceptual) table containing information on configured EVI-Link.
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfTunnelEviLinkEntry

hpnicfTunnelEviLinkEntry 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.5.1
An entry (conceptual row) containing the information on a particular configured EVI-Link.
OBJECT-TYPE    
  HpnicfTunnelEviLinkEntry  

hpnicfTunnelEviLinkNum 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.5.1.1
EVI-Link number.
OBJECT-TYPE    
  Integer32 1..2147483647  

hpnicfTunnelEviLinkIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.5.1.2
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  InterfaceIndex  

hpnicfTunnelEviLinkAddressType 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.5.1.3
The type of address in the corresponding hpnicfTunnelEviLinkRemoteAddr objects. Can not be modified after creation.
OBJECT-TYPE    
  InetAddressType  

hpnicfTunnelEviLinkRemoteAddr 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.5.1.4
The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header).
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelGreTable 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6
The (conceptual) table containing information on configured Gre-Tunnel.
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfTunnelGreEntry

hpnicfTunnelGreEntry 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1
An entry (conceptual row) containing the information on a particular configured Gre-Tunnel.
OBJECT-TYPE    
  HpnicfTunnelGreEntry  

hpnicfTunnelGreTunnNum 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.1
Tunnel number. An identifier used to distinguish between multiple tunnels.
OBJECT-TYPE    
  Integer32 1..2147483647  

hpnicfTunnelGreTunnIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.2
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  InterfaceIndex  

hpnicfTunnelGreAddressType 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.3
The type of address in the corresponding hpnicfTunnelGreLocalAddr and hpnicfTunnelGreRemoteAddr objects.
OBJECT-TYPE    
  InetAddressType  

hpnicfTunnelGreLocalAddr 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.4
The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header).
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelGreRemoteAddr 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.5
The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header).
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelGreKeepaliveEnabled 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.6
This MIB object specifies whether or not keepalive is used. A value of true indicates that keepalive SHOULD be used. When keepalive is not be used, the value of hpnicfTunnelGreKeepaliveInterval and hpnicfTunnelGreKeepaliveTimes MUST be zero.
OBJECT-TYPE    
  TruthValue  

hpnicfTunnelGreKeepaliveInterval 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.7
The method used to assign the keepalive interval. The value is zero when keepalive is not used. The valid value is from 1 to 32767, when keepalive is used.
OBJECT-TYPE    
  Integer32 0..32767  

hpnicfTunnelGreKeepaliveTimes 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.8
The method used to assign the keepalive maximum number of consecutive keepalive failures that are allowed. The value is zero when keepalive is not used. The valid value is from 1 to 255, when keepalive is used.
OBJECT-TYPE    
  Integer32 0..255  

hpnicfTunnelGreSlbgGroupNum 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.9
The method used to assign the service-loopback-group.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hpnicfTunnelGreTunnStatus 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.6.1.10
The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hpnicfTunnelGreTable may be modified while this row is active. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable.
OBJECT-TYPE    
  RowStatus  

hpnicfTunnelVxlanIfTable 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.7
The (conceptual) table containing information on configured Vxlan-Tunnel.
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfTunnelVxlanIfEntry

hpnicfTunnelVxlanIfEntry 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.7.1
An entry (conceptual row) containing the information on a particular configured Vxlan-Tunnel.
OBJECT-TYPE    
  HpnicfTunnelVxlanIfEntry  

hpnicfTunnelVxlanIfTunnNum 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.7.1.1
Tunnel number. An identifier used to distinguish between multiple tunnels.
OBJECT-TYPE    
  Integer32 1..2147483647  

hpnicfTunnelVxlanTunnIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.7.1.2
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  InterfaceIndex  

hpnicfTunnelVxlanIfAddressType 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.7.1.3
The type of address in the corresponding hpnicfTunnelVxlanIfLocalAddr and hpnicfTunnelVxlanIfRemoteAddr objects.
OBJECT-TYPE    
  InetAddressType  

hpnicfTunnelVxlanIfLocalAddr 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.7.1.4
The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header).
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelVxlanIfRemoteAddr 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.7.1.5
The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header).
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelVxlanIfStatus 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.7.1.6
The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hpnicfTunnelVxlanIfTable may be modified while this row is active. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable.
OBJECT-TYPE    
  RowStatus  

hpnicfTunnelVxlanConfigGroup 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.8
OBJECT IDENTIFIER    

hpnicfTunnelVxlanUdpPort 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.8.1
The UDP port number for Vxlan Tunnels.
OBJECT-TYPE    
  Integer32 1..65535  

hpnicfTunnelVxlanDropWrongCksmPkt 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.8.2
Whether or not dropping invalid UDP chesksum Vxlan packet.
OBJECT-TYPE    
  TruthValue  

hpnicfTunnelVxlanDropVlanTagPkt 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.8.3
Whether or not dropping Vxlan packet with inner VLAN tag.
OBJECT-TYPE    
  TruthValue  

hpnicfTunnelAvailableIDGroup 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.9
OBJECT IDENTIFIER    

hpnicfTunnelAvailableID 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.9.1
The available tunnel ID. A value of -1 indicates that there is no available tunnel ID.
OBJECT-TYPE    
  Integer32 -1 | 1..2147483647  

hpnicfTunnelTotalNumTable 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.10
Total number of a particular method tunnel.
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfTunnelTotalNumEntry

hpnicfTunnelTotalNumEntry 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.10.1
Total number of a particular method tunnel.
OBJECT-TYPE    
  HpnicfTunnelTotalNumEntry  

hpnicfTunnelEncapsMethod 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.10.1.1
The encapsulation method used by the tunnel.
OBJECT-TYPE    
  HpnicfTunnelType  

hpnicfTunnelTotalNum 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.10.1.2
Total number of a particular method tunnel.
OBJECT-TYPE    
  Unsigned32  

hpnicfTunnelNvgreIfTable 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.11
The (conceptual) table containing information on configured Nvgre-Tunnel.
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfTunnelNvgreIfEntry

hpnicfTunnelNvgreIfEntry 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.11.1
An entry (conceptual row) containing the information on a particular configured Nvgre-Tunnel.
OBJECT-TYPE    
  HpnicfTunnelNvgreIfEntry  

hpnicfTunnelNvgreIfTunnNum 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.11.1.1
Tunnel number. An identifier used to distinguish between multiple tunnels.
OBJECT-TYPE    
  Integer32 1..2147483647  

hpnicfTunnelNvgreTunnIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.11.1.2
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  InterfaceIndex  

hpnicfTunnelNvgreIfAddressType 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.11.1.3
The type of address in the corresponding hpnicfTunnelNvgreIfLocalAddr and hpnicfTunnelNvgreIfRemoteAddr objects.
OBJECT-TYPE    
  InetAddressType  

hpnicfTunnelNvgreIfLocalAddr 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.11.1.4
The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header).
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelNvgreIfRemoteAddr 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.11.1.5
The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header).
OBJECT-TYPE    
  InetAddress  

hpnicfTunnelNvgreIfStatus 1.3.6.1.4.1.11.2.14.11.15.2.53.1.1.11.1.6
The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hpnicfTunnelNvgreIfTable may be modified while this row is active. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable.
OBJECT-TYPE    
  RowStatus