HPN-ICF-NQA-MIB

Imported modules

SNMPv2-SMI	SNMPv2-TC	INET-ADDRESS-MIB
HPN-ICF-OID-MIB	DISMAN-PING-MIB	SNMP-FRAMEWORK-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Unsigned32
OBJECT-IDENTITY	NOTIFICATION-TYPE	Integer32
Counter32	Gauge32	DateAndTime
DisplayString	RowStatus	InetAddressType
InetAddress	hpnicfRhw	pingCtlEntry
pingCtlOwnerIndex	pingCtlTestName	pingCtlType
pingCtlTargetAddress	pingCtlTargetAddressType	pingCtlDescr
SnmpAdminString

Defined Types

HpnicfNqaCtlEntry
SEQUENCE
	hpnicfNqaCtlTargetPort	Integer32
	hpnicfNqaCtlSourcePort	Integer32
	hpnicfNqaCtlTTL	Integer32
	hpnicfNqaCtlJitterAdminInterval	Integer32
	hpnicfNqaCtlJitterAdminNumPackets	Integer32
	hpnicfNqaCtlHttpOperationType	INTEGER
	hpnicfNqaCtlHttpOperationString	DisplayString
	hpnicfNqaCtlFtpOperationType	INTEGER
	hpnicfNqaCtlFtpUsername	DisplayString
	hpnicfNqaCtlFtpPassword	DisplayString
	hpnicfNqaCtlFtpOperationString	DisplayString
	hpnicfNqaCtlVPNInstance	DisplayString
	hpnicfNqaCtlHistoryKeptTime	Integer32
	hpnicfNqaCtlHistoryEnable	INTEGER
	hpnicfNqaCtlICPIFAdvFactor	Integer32
	hpnicfNqaCtlCodecType	INTEGER

HpnicfNqaResultsEntry
SEQUENCE
	hpnicfNqaResultsRttNumDisconnects	Unsigned32
	hpnicfNqaResultsRttTimeouts	Unsigned32
	hpnicfNqaResultsRttBusies	Unsigned32
	hpnicfNqaResultsRttNoConnections	Unsigned32
	hpnicfNqaResultsRttDrops	Unsigned32
	hpnicfNqaResultsRttSequenceErrors	Unsigned32
	hpnicfNqaResultsRttStatsErrors	Unsigned32
	hpnicfNqaResultsMaxDelaySD	Unsigned32
	hpnicfNqaResultsMaxDelayDS	Unsigned32
	hpnicfNqaResultsLostPacketRatio	Unsigned32
	hpnicfNqaResultsPacketLateArrival	Unsigned32
	hpnicfNqaResultsRttSum	Unsigned32
	hpnicfNqaResultsNumOfDelaySD	Unsigned32
	hpnicfNqaResultsMinDelaySD	Unsigned32
	hpnicfNqaResultsSumDelaySD	Unsigned32
	hpnicfNqaResultsSum2DelaySD	Unsigned32
	hpnicfNqaResultsNumOfDelayDS	Unsigned32
	hpnicfNqaResultsMinDelayDS	Unsigned32
	hpnicfNqaResultsSumDelayDS	Unsigned32
	hpnicfNqaResultsSum2DelayDS	Unsigned32

HpnicfNqaJitterStatsEntry
SEQUENCE
	hpnicfNqaJitterStatsNumOfRTT	Counter32
	hpnicfNqaJitterStatsMinOfPositivesSD	Gauge32
	hpnicfNqaJitterStatsMaxOfPositivesSD	Gauge32
	hpnicfNqaJitterStatsNumOfPositivesSD	Gauge32
	hpnicfNqaJitterStatsSumOfPositivesSD	Gauge32
	hpnicfNqaJitterStatsSum2PositivesSD	Gauge32
	hpnicfNqaJitterStatsMinOfNegativesSD	Gauge32
	hpnicfNqaJitterStatsMaxOfNegativesSD	Gauge32
	hpnicfNqaJitterStatsNumOfNegativesSD	Gauge32
	hpnicfNqaJitterStatsSumOfNegativesSD	Gauge32
	hpnicfNqaJitterStatsSum2NegativesSD	Gauge32
	hpnicfNqaJitterStatsMinOfPositivesDS	Gauge32
	hpnicfNqaJitterStatsMaxOfPositivesDS	Gauge32
	hpnicfNqaJitterStatsNumOfPositivesDS	Gauge32
	hpnicfNqaJitterStatsSumOfPositivesDS	Gauge32
	hpnicfNqaJitterStatsSum2PositivesDS	Gauge32
	hpnicfNqaJitterStatsMinOfNegativesDS	Gauge32
	hpnicfNqaJitterStatsMaxOfNegativesDS	Gauge32
	hpnicfNqaJitterStatsNumOfNegativesDS	Gauge32
	hpnicfNqaJitterStatsSumOfNegativesDS	Gauge32
	hpnicfNqaJitterStatsSum2NegativesDS	Gauge32
	hpnicfNqaJitterStatsPacketLossSD	Gauge32
	hpnicfNqaJitterStatsPacketLossDS	Gauge32
	hpnicfNqaJitterStatsAvePositivesSD	Gauge32
	hpnicfNqaJitterStatsAveNegativesSD	Gauge32
	hpnicfNqaJitterStatsAvePositivesDS	Gauge32
	hpnicfNqaJitterStatsAveNegativesDS	Gauge32
	hpnicfNqaJitterStatsPktLossUnknown	Gauge32
	hpnicfNqaJitterStatsOperOfICPIF	Gauge32
	hpnicfNqaJitterStatsOperOfMOS	Gauge32

HpnicfNqaTcpServerEntry
SEQUENCE
	hpnicfNqaTcpServerIpAddress	InetAddress
	hpnicfNqaTcpServerPort	Integer32
	hpnicfNqaTcpServerRowStatus	RowStatus

HpnicfNqaUdpServerEntry
SEQUENCE
	hpnicfNqaUdpServerIpAddress	InetAddress
	hpnicfNqaUdpServerPort	Integer32
	hpnicfNqaUdpServerRowStatus	RowStatus

HpnicfNqaStatisticsCtlEntry
SEQUENCE
	hpnicfNqaCtlStatisticsInterval	Unsigned32
	hpnicfNqaCtlStatisticsGroupNumber	Unsigned32
	hpnicfNqaCtlStatisticsKeptTime	Unsigned32
	hpnicfNqaCtlBeginTime	DateAndTime
	hpnicfNqaCtlLifeTime	Unsigned32

HpnicfNqaStatisticsResultsEntry
SEQUENCE
	hpnicfNqaStatResIndex	Unsigned32
	hpnicfNqaStatResIpTargetAddressType	InetAddressType
	hpnicfNqaStatResIpTargetAddress	InetAddress
	hpnicfNqaStatResMinRtt	Gauge32
	hpnicfNqaStatResMaxRtt	Gauge32
	hpnicfNqaStatResAverageRtt	Gauge32
	hpnicfNqaStatResProbeResponses	Counter32
	hpnicfNqaStatResSentProbes	Counter32
	hpnicfNqaStatResRttSumOfSquares	Counter32
	hpnicfNqaStatResStartTime	DateAndTime
	hpnicfNqaStatResInterval	Gauge32
	hpnicfNqaStatResRttNumDisconnects	Counter32
	hpnicfNqaStatResRttTimeouts	Counter32
	hpnicfNqaStatResRttBusies	Counter32
	hpnicfNqaStatResRttNoConnections	Counter32
	hpnicfNqaStatResRttDrops	Counter32
	hpnicfNqaStatResRttSequenceErrors	Counter32
	hpnicfNqaStatResRttErrors	Counter32
	hpnicfNqaStatResLostPacketRatio	Gauge32
	hpnicfNqaStatResPacketLateArrival	Counter32
	hpnicfNqaStatResRttSum	Counter32
	hpnicfNqaStatResNumOfDelaySD	Counter32
	hpnicfNqaStatResMinDelaySD	Gauge32
	hpnicfNqaStatResMaxDelaySD	Gauge32
	hpnicfNqaStatResSumDelaySD	Counter32
	hpnicfNqaStatResSum2DelaySD	Counter32
	hpnicfNqaStatResNumOfDelayDS	Counter32
	hpnicfNqaStatResMinDelayDS	Gauge32
	hpnicfNqaStatResMaxDelayDS	Gauge32
	hpnicfNqaStatResSumDelayDS	Counter32
	hpnicfNqaStatResSum2DelayDS	Counter32

HpnicfNqaGroupStatsJitterEntry
SEQUENCE
	hpnicfNqaStatJitterIndex	Unsigned32
	hpnicfNqaStatJitterMinOfPosSD	Gauge32
	hpnicfNqaStatJitterMaxOfPosSD	Gauge32
	hpnicfNqaStatJitterNumOfPosSD	Counter32
	hpnicfNqaStatJitterSumOfPosSD	Counter32
	hpnicfNqaStatJitterSumOfSquarePosSD	Counter32
	hpnicfNqaStatJitterMinOfNegSD	Gauge32
	hpnicfNqaStatJitterMaxOfNegSD	Gauge32
	hpnicfNqaStatJitterNumOfNegSD	Counter32
	hpnicfNqaStatJitterSumOfNegSD	Counter32
	hpnicfNqaStatJitterSumOfSquareNegSD	Counter32
	hpnicfNqaStatJitterMinOfPosDS	Gauge32
	hpnicfNqaStatJitterMaxOfPosDS	Gauge32
	hpnicfNqaStatJitterNumOfPosDS	Counter32
	hpnicfNqaStatJitterSumOfPosDS	Counter32
	hpnicfNqaStatJitterSumOfSquarePosDS	Counter32
	hpnicfNqaStatJitterMinOfNegDS	Gauge32
	hpnicfNqaStatJitterMaxOfNegDS	Gauge32
	hpnicfNqaStatJitterNumOfNegDS	Counter32
	hpnicfNqaStatJitterSumOfNegDS	Counter32
	hpnicfNqaStatJitterSumOfSquareNegDS	Counter32
	hpnicfNqaStatJitterPacketLossSD	Counter32
	hpnicfNqaStatJitterPacketLossDS	Counter32
	hpnicfNqaStatJitterAvePosSD	Gauge32
	hpnicfNqaStatJitterAveNegSD	Gauge32
	hpnicfNqaStatJitterAvePosDS	Gauge32
	hpnicfNqaStatJitterAveNegDS	Gauge32
	hpnicfNqaStatJitterPktLossUnknown	Counter32
	hpnicfNqaStatJitterMaxOfICPIF	Gauge32
	hpnicfNqaStatJitterMinOfICPIF	Gauge32
	hpnicfNqaStatJitterMaxOfMOS	Gauge32
	hpnicfNqaStatJitterMinOfMOS	Gauge32

HpnicfNqaReactionEntry
SEQUENCE
	hpnicfNqaReactOwnerIndex	SnmpAdminString
	hpnicfNqaReactTestName	SnmpAdminString
	hpnicfNqaReactItemIndex	Unsigned32
	hpnicfNqaReactCheckedElement	INTEGER
	hpnicfNqaReactThresholdUpperLimit	Unsigned32
	hpnicfNqaReactThresholdLowerLimit	Unsigned32
	hpnicfNqaReactThresholdType	INTEGER
	hpnicfNqaReactThresholdConsecNum	Unsigned32
	hpnicfNqaReactThresholdAccumNum	Unsigned32
	hpnicfNqaReactActionType	INTEGER
	hpnicfNqaReactCurrentStatus	INTEGER
	hpnicfNqaReactRowStatus	RowStatus
	hpnicfNqaReactCheckedNum	Unsigned32
	hpnicfNqaReactThresholdNum	Unsigned32

HpnicfNqaStatisticsReactionEntry
SEQUENCE
	hpnicfNqaStatReactOwnerIndex	SnmpAdminString
	hpnicfNqaStatReactTestName	SnmpAdminString
	hpnicfNqaStatReactIndex	Unsigned32
	hpnicfNqaStatReactItemIndex	Unsigned32
	hpnicfNqaStatReactCheckedNum	Counter32
	hpnicfNqaStatReactThresholdNum	Counter32

Defined Values

hpnicfNqa		1.3.6.1.4.1.11.2.14.11.15.8.3
The private MIB file includes the test information of the device. It is supplementary for rfc2925.txt.
MODULE-IDENTITY

hpnicfNqaObjects		1.3.6.1.4.1.11.2.14.11.15.8.3.1
OBJECT IDENTIFIER

hpnicfNqaImplementationTypeDomains		1.3.6.1.4.1.11.2.14.11.15.8.3.2
OBJECT IDENTIFIER

hpnicfNqaUdpEcho		1.3.6.1.4.1.11.2.14.11.15.8.3.2.1
Indicates that an implementation is using the UDP based echo server. Notes: The hpnicfNqaCtlTargetPort and hpnicfNqaCtlSourcePort need to be set, while in the pingUdpEcho Node, hpnicfNqaCtlTargetPort must be set to the default value.
Status: current	Access: read-only
OBJECT-IDENTITY

hpnicfNqaTcpconnect		1.3.6.1.4.1.11.2.14.11.15.8.3.2.2
Indicates that an implementation is attempting to connect to a TCP port in order to calculate a round trip time. Notes: The hpnicfNqaCtlTargetPort and hpnicfNqaCtlSourcePort need to be set, while in the pingTcpConnectionAttempt Node, hpnicfNqaCtlTargetPort must be set to the default value.
Status: current	Access: read-only
OBJECT-IDENTITY

hpnicfNqajitter		1.3.6.1.4.1.11.2.14.11.15.8.3.2.3
Indicates that an implementation is using udp for packet transfers. 'jitter' will cause the NQA(Network Quality Analysis) application to perform delay variance analysis.
Status: current	Access: read-only
OBJECT-IDENTITY

hpnicfNqaHttp		1.3.6.1.4.1.11.2.14.11.15.8.3.2.4
Indicates that an implementation is using udp for name resolution, tcp connect and tcp data transfer mechanisms for HTTP data download from a particular HTTP Server. It causes the NQA application to perform a download of the object specified in the URL.
Status: current	Access: read-only
OBJECT-IDENTITY

hpnicfNqadlsw		1.3.6.1.4.1.11.2.14.11.15.8.3.2.5
Indicates that an implementation is using tcp for sending keepalives. 'dlsw' will cause the NQA application to perform a keepalive operation to measure the response time of a DLSw peer.
Status: current	Access: read-only
OBJECT-IDENTITY

hpnicfNqadhcp		1.3.6.1.4.1.11.2.14.11.15.8.3.2.6
Indicates that an implementation is using udp for sending dhcp requests. 'dhcp' will cause the NQA application to perform an IP Address lease request/teardown operation.
Status: current	Access: read-only
OBJECT-IDENTITY

hpnicfNqaftp		1.3.6.1.4.1.11.2.14.11.15.8.3.2.7
Indicates that an implementation is using tcp packet for ftp connect and data transfer.
Status: current	Access: read-only
OBJECT-IDENTITY

hpnicfNqaMIBVersion		1.3.6.1.4.1.11.2.14.11.15.8.3.1.1
Version string of this MIB. The format will be: 'Version.Release.Patch: Description' An instance likes: '1.0.0: Initial NQA MIB'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hpnicfNqaCtlTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2
Defines the NQA Control Extend Table for providing, via SNMP, the capability of performing network analysis operations at a remote host.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaCtlEntry

hpnicfNqaCtlEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1
Defines an entry in the hpnicfNqaCtlTable. The operation of this table is same as that of pingResultsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaCtlEntry

hpnicfNqaCtlTargetPort		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.1
The destination port that may be used by udpEcho, tcpConnect and jitter probes.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65536

hpnicfNqaCtlSourcePort		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.2
The source port that may be used by all tests except for dns and dlsw. If no source port is specified, system will create a random port as source port.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65536

hpnicfNqaCtlTTL		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.3
Specifies the value to store in the TTL Field in the IP packet used to encapsulate the NQA probe.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfNqaCtlJitterAdminInterval		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.4
Time value in milliseconds that is an interval between two continuous probes in jitter test. This object is only used by jitter test.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..60000

hpnicfNqaCtlJitterAdminNumPackets		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.5
Packet number that specifys how many packets will be sent in one jitter test. This object is only used by jitter test.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfNqaCtlHttpOperationType		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.6
Http operation type: get, post or raw.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	get(1), post(2), raw(3)

hpnicfNqaCtlHttpOperationString		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.7
Http operation string. For example, if the http operation type is get, the string will be url, home page and http version.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..1023)

hpnicfNqaCtlFtpOperationType		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.8
Ftp operation type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	get(1), put(2)

hpnicfNqaCtlFtpUsername		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.9
Ftp username.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

hpnicfNqaCtlFtpPassword		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.10
Ftp password.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

hpnicfNqaCtlFtpOperationString		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.11
Ftp operation string. If the ftp operation type is get, the string must be the file name which will be gotten from ftp server.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..255)

hpnicfNqaCtlVPNInstance		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.12
VPN name by which system finds route in the specified VPN to send NQA probe packets.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..255)

hpnicfNqaCtlHistoryKeptTime		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.13
To indicate how long the history records will be saved in the pingProbeHistoryTable table after the test stopped.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..1440

hpnicfNqaCtlHistoryEnable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.14
To indicate whether the history should be recorded in the PingProbeHistoryTable or not. enabled(1) --history will be recorded disabled(2) --history will not be recorded.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

hpnicfNqaCtlICPIFAdvFactor		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.15
The advantage factor depends on the type of access and how the service is to be used. This object will be used while calculating the ICPIF (Calculated Planning Impairment Factor) values. This is applicable only for the jitter probe. Suggestion values: \|-----------------------------------\|-------\| \| Service \|factor \| \|-----------------------------------\|-------\| \|conventional wire-line \| 0 \| \|-----------------------------------\|-------\| \|mobility within Building \| 5 \| \|-----------------------------------\|-------\| \|mobility within geographical area \| 10 \| \|-----------------------------------\|-------\| \|access to hard-to-reach location \| 20 \| \|-----------------------------------\|-------\|
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfNqaCtlCodecType		1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.16
To indicate the codec type to be used with jitter probe. This is applicable only for the jitter probe.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notDefined(1), g711Alaw(2), g711Ulaw(3), g729A(4), icmpTimestamp(5)

hpnicfNqaResultsTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3
Defines the NQA Results Extend Table for providing the capability of performing NQA operations at a remote host. The results of these operations are stored in the hpnicfNqaResultsTable. The operation of this table is same as that of pingResultsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaResultsEntry

hpnicfNqaResultsEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1
The operation of this table is same as that of pingResultsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaResultsEntry

hpnicfNqaResultsRttNumDisconnects		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.1
The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsRttTimeouts		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.2
The number of times that a NQA probe failed because the probe timed out.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsRttBusies		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.3
The number of times that a NQA probe failed because all NQA tasks have been running. If a new probe fails to start, the value of this object is incremented. The next test will not start until the next Frequency.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsRttNoConnections		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.4
The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsRttDrops		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.5
The number of times that a NQA operation failed to initiated for unavailibility of necessary internal resources.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsRttSequenceErrors		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.6
The number of packets arrived out of sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsRttStatsErrors		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.7
The number of some other errors.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsMaxDelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.8
The maximal delay from source device to destination device. Currently this value is only used for jitter test, and this value must be 0 in other type test. In jitter test, if destination system time is not valid, the SD delay may be set 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsMaxDelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.9
The maximal delay from destination device to source device. Currently this value is only used for jitter test, and this value is 0 in other type test. In jitter test, if destination system time is not valid, the DS delay may be set 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsLostPacketRatio		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.10
The value of this object reflects the drop rate of NQA test. For example, this value is 30 that means source device only had received 70% packets of total sent packets.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsPacketLateArrival		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.11
The value of this object indicates the number of the packets that arrived after the timeout.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsRttSum		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.12
The sum of round trip time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsNumOfDelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.13
The number of delay from source to destination that are successfully measured.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsMinDelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.14
The minimum of all one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsSumDelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.15
The sum of one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsSum2DelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.16
The sum of squares of one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsNumOfDelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.17
The number of delay from destination to source that are successfully measured.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsMinDelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.18
The minimum of all one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsSumDelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.19
The sum of one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaResultsSum2DelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.20
The sum of squares of one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaJitterStatsTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4
Statistics table for latest jitter activity.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaJitterStatsEntry

hpnicfNqaJitterStatsEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1
An entry contains the statistics for the latest jitter activity. This entry is created only if the pingCtlType is hpnicfNqajitter.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaJitterStatsEntry

hpnicfNqaJitterStatsNumOfRTT		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.1
The number of received destination device responses with which jitter test can reach round-trip time.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaJitterStatsMinOfPositivesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.2
The value of time that records the minimal positive jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsMaxOfPositivesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.3
The value of time that records the maximal positive jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsNumOfPositivesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.4
The number that records positive jitter times from source to destination in the jitter test. The total number of the value of all positive jitters in packets sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsSumOfPositivesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.5
The value of time that records the sum of positive jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsSum2PositivesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.6
The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsMinOfNegativesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.7
The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsMaxOfNegativesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.8
The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsNumOfNegativesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.9
The number that records negative jitter times from source to destination in the jitter test. The total number of all negative jitter values in packets sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsSumOfNegativesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.10
The value of time that records the sum of negative jitter values from source to destination in the jitter test. The total number of the value of all negative jitters in packets sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsSum2NegativesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.11
The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsMinOfPositivesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.12
The value of time that records the minimal positive jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsMaxOfPositivesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.13
The value of time that records the maximal positive jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsNumOfPositivesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.14
The number that records positive jitter times from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsSumOfPositivesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.15
The value of time that records the sum of positive jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsSum2PositivesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.16
The value of time that records the sum of square of positive jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsMinOfNegativesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.17
The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsMaxOfNegativesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.18
The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsNumOfNegativesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.19
The number that records negative jitter times from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsSumOfNegativesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.20
The value of time that records the sum of negative jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsSum2NegativesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.21
The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsPacketLossSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.22
The lost packets number sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsPacketLossDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.23
The lost packets number sent from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsAvePositivesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.24
The value of time that records the average positive jitter value from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsAveNegativesSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.25
The value of time that records the average negative jitter value from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsAvePositivesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.26
The value of time that records the average positive jitter value from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsAveNegativesDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.27
The value of time that records the average negative jitter value from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsPktLossUnknown		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.28
The number of packets which is lost with unknown reason.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsOperOfICPIF		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.29
The ICPIF (Calculated Planning Impairment Factor) value for the latest jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaJitterStatsOperOfMOS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.30
The MOS (Mean Opinion Score) value for the latest jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaAgentEnable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.5
Enable NQA agent function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hpnicfNqaTcpServerTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.6
A table which contains the status of NQA tcp server configuration information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaTcpServerEntry

hpnicfNqaTcpServerEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.6.1
A table which contains the status of NQA tcp server configuration information. This entry includes not only the tcp server ip address but also the tcp server port.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaTcpServerEntry

hpnicfNqaTcpServerIpAddress		1.3.6.1.4.1.11.2.14.11.15.8.3.1.6.1.1
Tcp server's ip address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

hpnicfNqaTcpServerPort		1.3.6.1.4.1.11.2.14.11.15.8.3.1.6.1.2
Tcp server's port number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65536

hpnicfNqaTcpServerRowStatus		1.3.6.1.4.1.11.2.14.11.15.8.3.1.6.1.3
hpnicfNqaTcpServerIpAddress and hpnicfNqaTcpServerPort must be set during a creation operation.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hpnicfNqaUdpServerTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.7
Status of NQA udp server configuration information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaUdpServerEntry

hpnicfNqaUdpServerEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.7.1
This entry includes not only the udp server ip address but also the udp server udp port.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaUdpServerEntry

hpnicfNqaUdpServerIpAddress		1.3.6.1.4.1.11.2.14.11.15.8.3.1.7.1.1
Udp server's ip address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

hpnicfNqaUdpServerPort		1.3.6.1.4.1.11.2.14.11.15.8.3.1.7.1.2
Udp server's port number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65536

hpnicfNqaUdpServerRowStatus		1.3.6.1.4.1.11.2.14.11.15.8.3.1.7.1.3
hpnicfNqaUdpServerIpAddress and hpnicfNqaUdpServerPort must be set during a creation operation.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hpnicfNqaServerEnable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.8
Enable NQA server function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hpnicfNqaStatsMaxGroupNumber		1.3.6.1.4.1.11.2.14.11.15.8.3.1.9
The maximum number saved per group. The maximum value of hpnicfNqaCtlStatisticsGroupNumber can not exceed the value of this object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfNqaStatisticsCtlTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.10
Defines the NQA statistics control table for providing, via SNMP, the capability of performing NQA operations at a remote host. The results of these operations are stored in the hpnicfNqaStatisticsResultsTable and the hpnicfNqaGroupStatsJitterTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaStatisticsCtlEntry

hpnicfNqaStatisticsCtlEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1
Defines an entry in the hpnicfNqaStatisticsCtlTable. The hpnicfNqaStatisticsCtlTable has the same index as the pingCtlTable in order for a hpnicfNqaStatisticsCtlTable to correspond to the pingCtlEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaStatisticsCtlEntry

hpnicfNqaCtlStatisticsInterval		1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.1
Statistic information will be calculated after the time that is the value of hpnicfNqaCtlStatisticsInterval.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hpnicfNqaCtlStatisticsGroupNumber		1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.2
The value of this object indicates the number of group saved. The length of this object is from 1 to hpnicfNqaStatsMaxGroupNumber.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hpnicfNqaCtlStatisticsKeptTime		1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.3
To indicate how long the statistic information will be saved after the test stops.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..1440

hpnicfNqaCtlBeginTime		1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.4
Time at which the type-specified test will start.
Status: current	Access: read-create
OBJECT-TYPE
	DateAndTime

hpnicfNqaCtlLifeTime		1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.5
To indicate how long the type-specified test will last.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hpnicfNqaStatisticsResultsTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11
Defines the NQA statistics results table for providing the capability of performing NQA operations at a remote host. The statistics results of these operations in a statistic cycle are stored in the hpnicfNqaStatisticsResultsTable. The statistic cycle is the value of hpnicfNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that the probe statistics result (HpnicfNqaStatisticsResultsEntry) belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaStatisticsResultsEntry

hpnicfNqaStatisticsResultsEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1
Defines an entry in the hpnicfNqaStatisticsResultsTable. The hpnicfNqaStatisticsResultsTable has the same index as the pingCtlTable in order for a hpnicfNqaStatisticsResultsEntry to correspond to the pingCtlEntry that caused it to be created.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaStatisticsResultsEntry

hpnicfNqaStatResIndex		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.1
An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hpnicfNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..ffffffff

hpnicfNqaStatResIpTargetAddressType		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.2
This object indicates the type of address stored in the corresponding hpnicfNqaStatResIpTargetAddress object.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

hpnicfNqaStatResIpTargetAddress		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.3
This object represent the host address to be used at a remote host for performing a network analysis operation.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

hpnicfNqaStatResMinRtt		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.4
The minimum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResMaxRtt		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.5
The maximum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResAverageRtt		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.6
The average NQA probe round-trip-time (RTT).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResProbeResponses		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.7
The number of responses received. The value of this object MUST be reported as 0 when no probe responses have been received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResSentProbes		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.8
The value of this object reflects the number of probes sent. The value of this object MUST be reported as 0 when no probes have been sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResRttSumOfSquares		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.9
This object contains the sum of the squares for all NQA responses received. The value of this object MUST be reported as 0 when no NQA responses have been received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResStartTime		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.10
This object contains the start time of the statistic.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hpnicfNqaStatResInterval		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.11
This object contains the interval between two times of statistic.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResRttNumDisconnects		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.12
The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResRttTimeouts		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.13
The number of times that a probe failed because the probe timed out.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResRttBusies		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.14
The number of times that a NQA probe failed because errors related to sockets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResRttNoConnections		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.15
The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResRttDrops		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.16
The number of times that a NQA operation failed to initiate for unavailibility of necessary internal resources.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResRttSequenceErrors		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.17
The number of packets arrived out of sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResRttErrors		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.18
The number of other errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResLostPacketRatio		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.19
The value of this object reflects the drop rate of NQA test packet. For example, if the value is 30, that means source device only had received 70 percent packets of total sent packets.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResPacketLateArrival		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.20
The value of this object reflects the number of the packets that arrived after the timeout.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResRttSum		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.21
This object contains the sum of the squares for all NQA responses received during the test lifetime. The value of this object MUST be reported as 0 when no NQA responses have been received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResNumOfDelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.22
The number of one way times from source to destination that are successfully measured.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResMinDelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.23
The minimum one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResMaxDelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.24
The maximum one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResSumDelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.25
The sum of one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResSum2DelaySD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.26
The sum of squares of one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResNumOfDelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.27
The number of one way times from destination to source that are successfully measured.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResMinDelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.28
The minimum one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResMaxDelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.29
The maximum one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatResSumDelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.30
The sum of one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatResSum2DelayDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.31
The sum of squares of one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaGroupStatsJitterTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12
Test Group Statistic table for jitter activity in a statistic cycle. The statistic cycle is the value of hpnicfNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that a probe statistics result (HpnicfNqaStatisticsResultsEntry) belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaGroupStatsJitterEntry

hpnicfNqaGroupStatsJitterEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1
An entry contains the group statistic information for jitter activity. This entry is created only if the pingCtlType is hpnicfNqajitter.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaGroupStatsJitterEntry

hpnicfNqaStatJitterIndex		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.1
An entry in this table is created when the statistic result of a NQA probe in a statistic cycle is determined. An implementation MUST start assigning hpnicfNqaStatJitterIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..ffffffff

hpnicfNqaStatJitterMinOfPosSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.2
The value of time that records the minimal positive jitter value from source to destination in jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterMaxOfPosSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.3
The value of time that records the maximal positive jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterNumOfPosSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.4
The total number of positive jitters from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterSumOfPosSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.5
The value of time that records the sum of positive jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterSumOfSquarePosSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.6
The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterMinOfNegSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.7
The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterMaxOfNegSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.8
The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterNumOfNegSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.9
The total number of negative jitters from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterSumOfNegSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.10
The value of time that records the sum of negative jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterSumOfSquareNegSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.11
The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterMinOfPosDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.12
The value of time that records the minimal positive jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterMaxOfPosDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.13
The value of time that records the maximal positive jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterNumOfPosDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.14
The total number of positive jitters from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterSumOfPosDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.15
The value of time that records the sum of positive jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterSumOfSquarePosDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.16
The value of time that records the sum of square of positive jitter values destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterMinOfNegDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.17
The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterMaxOfNegDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.18
The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterNumOfNegDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.19
The total number of negative jitters from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterSumOfNegDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.20
The value of time that records the sum of negative jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterSumOfSquareNegDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.21
The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterPacketLossSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.22
The lost packets number sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterPacketLossDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.23
The lost packets number sent from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterAvePosSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.24
The value of time that records the average positive jitter value from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterAveNegSD		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.25
The value of time that records the average negative jitter value from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterAvePosDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.26
The value of time that records the average positive jitter value from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterAveNegDS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.27
The value of time that records the average negative jitter value from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterPktLossUnknown		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.28
The number of packets which is lost with unknown reason.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatJitterMaxOfICPIF		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.29
The maximum of all ICPIF values in a statistic cycle for jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterMinOfICPIF		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.30
The minimum of all ICPIF values in a statistic cycle for jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterMaxOfMOS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.31
The maximum of all MOS values in a statistic cycle for jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaStatJitterMinOfMOS		1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.32
The minimum of all MOS values in a statistic cycle for jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hpnicfNqaReactionTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13
A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaReactionEntry

hpnicfNqaReactionEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1
Defines an entry in the hpnicfNqaReactionTable. The first two index elements identify the pingCtlEntry that a hpnicfNqaReactItemIndex belongs to. The third index element selects a single reaction.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaReactionEntry

hpnicfNqaReactOwnerIndex		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.1
The first index of hpnicfNqaReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable. hpnicfNqaReactOwnerIndex and hpnicfNqaReactTestName identify an existed test.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

hpnicfNqaReactTestName		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.2
The second index of hpnicfNqaReactionTable, it is the same as pingCtlTestName in pingCtlTable. hpnicfNqaReactOwnerIndex and hpnicfNqaReactTestName identify an existed test.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

hpnicfNqaReactItemIndex		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.3
The third index of hpnicfNqaReactionTable, it definitely identifies one of the reaction configurations for a test.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32	1..10

hpnicfNqaReactCheckedElement		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.4
A list of reaction condition type. 'probetime' and 'probefailure' are valid when pingCtlType of the test is not hpnicfNqajitter. 'jitterOwdSD': one way time from source to destination in jitter test. 'jitterOwdDS': one way time from destination to source in jitter test. 'jitterrtt', 'jitterpacketloss', 'jittersd', 'jitterds', 'jitterOwdSD' and 'jitterOwdDS' are valid when pingCtlType of the test is hpnicfNqajitter. 'icpif' and 'mos' are valid when pingCtlType of the test is hpnicfNqajitter and hpnicfNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	probetime(1), probefailure(2), jitterrtt(3), jitterpacketloss(4), jittersd(5), jitterds(6), icpif(7), mos(8), jitterOwdSD(9), jitterOwdDS(10)

hpnicfNqaReactThresholdUpperLimit		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.5
This object defines an administrative upper-threshold value for hpnicfNqaReactCheckedElement. The value of this object is zero if hpnicfNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hpnicfNqaReactThresholdLowerLimit		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.6
This object defines an administrative lower-threshold value for hpnicfNqaReactCheckedElement. The value of hpnicfNqaReactThresholdLowerLimit should be equal or less than the value of hpnicfNqaReactThresholdUpperLimit. The value of this object is zero if hpnicfNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hpnicfNqaReactThresholdType		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.7
This object defines the reaction threshold types. invalid(0): Invalid value. average(1): If reaction threshold type is average and the average value of watched operation exceeds threshold limit, an action specified in hpnicfNqaReactActionType is generated when hpnicfNqaReactCurrentStatus changes. consecutive(2): If reaction threshold type is consecutive and the times of watched operation consecutively exceeds the limit specified by hpnicfNqaReactThresholdConsecNum, an action specified in hpnicfNqaReactActionType is generated when hpnicfNqaReactCurrentStatus changes. accumulative(3): If reaction threshold type is accumulative and the times of watched operation accumulatively exceeds the limit specified by hpnicfNqaReactThresholdAccumNum, an action specified in hpnicfNqaReactActionType is generated when hpnicfNqaReactCurrentStatus changes. If reaction threshold type is not configured, the value of this object is 'invalid'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	invalid(0), average(1), consecutive(2), accumulative(3)

hpnicfNqaReactThresholdConsecNum		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.8
This object defines a consecutive threshold limit. The value is zero when hpnicfNqaReactThresholdType is not 'consecutive'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hpnicfNqaReactThresholdAccumNum		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.9
This object defines an accumulative threshold limit. The value is zero when the hpnicfNqaReactThresholdType is not 'accumulative'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hpnicfNqaReactActionType		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.10
Specifies the type of reaction to generate if the specified violation type occurs for the monitored element: none - No reaction is generated trapOnly - A trap is generated triggerOnly - All trigger actions defined for this entry are generated trapAndTrigger - Both a trap and all trigger actions are generated
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), trapOnly(1), triggerOnly(2), trapAndTrigger(3)

hpnicfNqaReactCurrentStatus		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.11
Specifies the current status of this reaction entry: invalid - The status of the reaction entry is unknown. overThreshold - The status of the reaction entry is overThreshold when the monitored result exceeds the threshold value for the hpnicfNqaReactThresholdType. belowThreshold - The status of the reaction entry is belowThreshold when the monitored result is under the threshold value for the hpnicfNqaReactThresholdType.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	invalid(1), overThreshold(2), belowThreshold(3)

hpnicfNqaReactRowStatus		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.12
This object allows entries to be created and deleted in the hpnicfNqaReactionTable. Creation of an entry in this table results in a new set of reaction configurations which take effect immediately. Deletion of an entry in this table results in corresponding reaction configurations are being deleted and stop taking effect.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hpnicfNqaReactCheckedNum		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.13
The number of checked element samples that are monitored.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaReactThresholdNum		1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.14
The number of checked element samples that are over threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfNqaStatisticsReactionTable		1.3.6.1.4.1.11.2.14.11.15.8.3.1.14
A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfNqaStatisticsReactionEntry

hpnicfNqaStatisticsReactionEntry		1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1
Defines an entry in the hpnicfNqaStatisticsReactionTable. The first two index elements identify the pingCtlEntry that a hpnicfNqaReactItemIndex belongs to. The third index element identifies an entry in the hpnicfNqaStatisticsResultsTable. The forth index element selects a single reaction.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfNqaStatisticsReactionEntry

hpnicfNqaStatReactOwnerIndex		1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.1
The first index of hpnicfNqaStatisticsReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

hpnicfNqaStatReactTestName		1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.2
The second index of hpnicfNqaStatisticsReactionTable, it is the same as pingCtlTestName in pingCtlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

hpnicfNqaStatReactIndex		1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.3
The third index of hpnicfNqaStatisticsReactionTable. An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hpnicfNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hpnicfNqaStatReactItemIndex		1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.4
The forth index of hpnicfNqaStatisticsReactionTable, it definitely identifies one of the reaction configurations for a test
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hpnicfNqaStatReactCheckedNum		1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.5
The number of checked element samples that are monitored.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaStatReactThresholdNum		1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.6
The number of checked element samples that are over threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hpnicfNqaNotifications		1.3.6.1.4.1.11.2.14.11.15.8.3.3
OBJECT IDENTIFIER

hpnicfNqaProbeTimeOverThreshold		1.3.6.1.4.1.11.2.14.11.15.8.3.3.1
It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. Probe time(equals to RTT for some type of tests) is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit. 2. The probe time is accumulatively not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdAccumNum. 3. The probe time is consecutively in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdConsecNum. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hpnicfNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfNqaJitterRTTOverThreshold		1.3.6.1.4.1.11.2.14.11.15.8.3.3.2
It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average NQA round-trip-time (RTT) of jitter packets is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit. 2. The RTT of jitter packets is accumulatively not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdAccumNum in one test. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hpnicfNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfNqaProbeFailure		1.3.6.1.4.1.11.2.14.11.15.8.3.3.3
It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the probe test accumulatively failed for a number of times specified in hpnicfNqaReactThresholdAccumNum in one test while the value of hpnicfNqaReactThresholdType is 'accumulative'. 2. When the probe test consecutively failed for a number of times specified in hpnicfNqaReactThresholdConsecNum in one test while the value of hpnicfNqaReactThresholdType is 'consecutive'. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hpnicfNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfNqaJitterPacketLoss		1.3.6.1.4.1.11.2.14.11.15.8.3.3.4
It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the jitter packets accumulatively lost for a number of times specified in hpnicfNqaReactThresholdAccumNum in one test while the value of hpnicfNqaReactThresholdType is 'accumulative'. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hpnicfNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfNqaJitterSDOverThreshold		1.3.6.1.4.1.11.2.14.11.15.8.3.3.5
The SD means the jitter values from source to destination. It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of SD in one jitter test is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit and the hpnicfNqaReactThresholdType is specified as 'average' type. 2. The average of SD in one jitter test is accumulatively not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdAccumNum and the hpnicfNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hpnicfNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfNqaJitterDSOverThreshold		1.3.6.1.4.1.11.2.14.11.15.8.3.3.6
The DS means the jitter values from destination to source. It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of DS in one jitter test is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit and the hpnicfNqaReactThresholdType is specified as 'average' type. 2. The average of DS in one jitter test is accumulatively not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdAccumNum and the hpnicfNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hpnicfNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfNqaICPIFOverThreshold		1.3.6.1.4.1.11.2.14.11.15.8.3.3.7
It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the ICPIF value in one jitter test is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hpnicfNqajitter and hpnicfNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfNqaMOSOverThreshold		1.3.6.1.4.1.11.2.14.11.15.8.3.3.8
It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the MOS value in one jitter test is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hpnicfNqajitter and hpnicfNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current	Access: read-only
NOTIFICATION-TYPE