HPN-ICF-EPON-UNI-MIB

File: HPN-ICF-EPON-UNI-MIB.mib (66981 bytes)

Imported modules

HPN-ICF-OID-MIB	IF-MIB	SNMPv2-SMI
SNMPv2-TC

Imported symbols

hpnicfEpon	ifIndex	ifDescr
Integer32	Unsigned32	IpAddress
OBJECT-TYPE	MODULE-IDENTITY	NOTIFICATION-TYPE
MacAddress	TruthValue	RowStatus

Defined Types

HpnicfEponUniSysManEntry
SEQUENCE
	hpnicfEponUniIndex	Integer32
	hpnicfEponUniDescr	OCTET STRING
	hpnicfEponUniAdminStatus	INTEGER
	hpnicfEponUniMdi	INTEGER
	hpnicfEponUniPriority	Integer32
	hpnicfEponUniVlanType	INTEGER
	hpnicfEponUniAccessVlan	Integer32
	hpnicfEponUniTrunkPvid	INTEGER
	hpnicfEponUniVLANTrunkAllowListLow	OCTET STRING
	hpnicfEponUniVLANTrunkAllowListHigh	OCTET STRING
	hpnicfEponUniInboundLineRate	Integer32
	hpnicfEponUniOutboundLineRate	Integer32
	hpnicfEponUniFlowControl	TruthValue
	hpnicfEponUniSpeed	INTEGER
	hpnicfEponUniDuplex	INTEGER
	hpnicfEponUniVlanVPNStatus	TruthValue
	hpnicfEponUniCountReset	INTEGER
	hpnicfEponUniPortIsolate	INTEGER
	hpnicfEponUniVlanConfiguration	OCTET STRING
	hpnicfEponUniAutoNegotiation	INTEGER
	hpnicfEponUniRestartAutoNeg	INTEGER
	hpnicfEponUniLinkStatus	INTEGER
	hpnicfEponUniInterfaceType	INTEGER
	hpnicfEponUniVitualCableTest	INTEGER
	hpnicfEponUniVCTCableStatus	INTEGER
	hpnicfEponUniVCTCableLength	Integer32
	hpnicfEponUniVCTImpedanceMismatch	INTEGER
	hpnicfEponUniVCTPairSkew	Integer32
	hpnicfEponUniVCTPairSwap	INTEGER
	hpnicfEponUniVCTPolaritySwap	INTEGER
	hpnicfEponUniVCTInsertionLoss	Integer32
	hpnicfEponUniVCTReturnLoss	Integer32
	hpnicfEponUniVCTNearendCrosstalk	Integer32
	hpnicfEponUniVlan	Integer32

HpnicfEponUniCountEntry
SEQUENCE
	hpnicfEponUniInStatsPkts	Unsigned32
	hpnicfEponUniInStatsUnicastPkts	Unsigned32
	hpnicfEponUniInStatsBroadcastPkts	Unsigned32
	hpnicfEponUniInStatsMulticastPkts	Unsigned32
	hpnicfEponUniInPausePkts	Unsigned32
	hpnicfEponUniInTotalErrors	Unsigned32
	hpnicfEponUniInStatsCRCAlignErrors	Unsigned32
	hpnicfEponUniInStatsUndersizePkts	Unsigned32
	hpnicfEponUniInStatsOversizePkts	Unsigned32
	hpnicfEponUniInErrorbyOther	Unsigned32
	hpnicfEponUniOutStatsPkts	Unsigned32
	hpnicfEponUniOutStatsUnicastPkts	Unsigned32
	hpnicfEponUniOutStatsBroadcastPkts	Unsigned32
	hpnicfEponUniOutStatsMulticastPkts	Unsigned32
	hpnicfEponUniOutStatsPausePkts	Unsigned32
	hpnicfEponUniOutTotalErrors	Unsigned32
	hpnicfEponUniOutStatsCollisions	Unsigned32
	hpnicfEponUniOutDelayExceededDiscards	Unsigned32
	hpnicfEponUniOutErrorbyOther	Unsigned32
	hpnicfEponUniOutDroppedFrames	Unsigned32

HpnicfEponUniIgmpInfoEntry
SEQUENCE
	hpnicfEponUniMacIndex	Integer32
	hpnicfEponUniIgmpMacAddress	MacAddress
	hpnicfEponUniIgmpVlanId	Integer32

HpnicfEponUniPortPolicyEntry
SEQUENCE
	hpnicfEponUniPortPolicyStatus	INTEGER
	hpnicfEponUniPortPolicyCir	Integer32
	hpnicfEponUniPortPolicyBucketDepth	Integer32
	hpnicfEponUniPortPolicyExtraBurst	Integer32
	hpnicfEponUniPortPolicyInboundCir	Integer32
	hpnicfEponUniPortPolicyInboundBucketDepth	Integer32
	hpnicfEponUniPortPolicyInboundExtraBurst	Integer32
	hpnicfEponUniPortPolicyOutboundCir	Integer32
	hpnicfEponUniPortPolicyOutboundPir	Integer32

HpnicfEponUniMulticastEntry
SEQUENCE
	hpnicfEponUniMulticastGroupNumber	Integer32
	hpnicfEponUniMulticastVlanList	OCTET STRING
	hpnicfEponUniMulticastStripStatus	INTEGER
	hpnicfEponUniMulticastFastleave	TruthValue

HpnicfEponUniTechAbilityEntry
SEQUENCE
	hpnicfEponUniLocalTechAbility	OCTET STRING
	hpnicfEponUniAdvertisedTechAbility	OCTET STRING

HpnicfEponUniMulticastControlEntry
SEQUENCE
	hpnicfEponUniMulticastVlanIndex	Integer32
	hpnicfEponUniMulticastAddressList	OCTET STRING
	hpnicfEponUniMulticastAccessRule	INTEGER
	hpnicfEponUniMulticastChannelLimit	Integer32
	hpnicfEponUniMulticastPreTimeSlice	Integer32
	hpnicfEponUniMulticastPreTimes	Integer32
	hpnicfEponUniMulticastPreInterval	Integer32
	hpnicfEponUniMulticastRowStatus	RowStatus
	hpnicfEponUniMulticastIndex	INTEGER
	hpnicfEponUniMulticastSourceIpList	OCTET STRING
	hpnicfEponUniMulticastResetInterval	Integer32

HpnicfEponUniQosIndexNextEntry
SEQUENCE
	hpnicfEponUniQosConfIndexNext	Integer32

HpnicfEponUniQosConfEntry
SEQUENCE
	hpnicfEponUniQosConfIndex	Integer32
	hpnicfEponUniQosConfRuleIndexNext	Integer32
	hpnicfEponUniQosConfMappedQueue	Integer32
	hpnicfEponUniQosConfMarkedPriority	Integer32
	hpnicfEponUniQosConfRowStatus	RowStatus

HpnicfEponUniQosRuleEntry
SEQUENCE
	hpnicfEponUniQosRuleIndex	Integer32
	hpnicfEponUniQosRuleSelector	INTEGER
	hpnicfEponUniQosRuleValue	Integer32
	hpnicfEponUniQosRuleMacAddress	MacAddress
	hpnicfEponUniQosRuleOperator	INTEGER
	hpnicfEponUniQosRuleRowStatus	RowStatus

HpnicfEponUniMirrorGroupEntry
SEQUENCE
	hpnicfEponUniMirrorGroupID	Integer32
	hpnicfEponUniMirrorInboundPortList	OCTET STRING
	hpnicfEponUniMirrorOutboundPortList	OCTET STRING
	hpnicfEponUniMonitorPort	Integer32
	hpnicfEponUniMirrorRowStatus	RowStatus

HpnicfEponUniMirrorGroupIdNextEntry
SEQUENCE
	hpnicfEponUniMirrorGroupIDNext	Integer32

HpnicfEponUniMulticastCtrlInfoEntry
SEQUENCE
	hpnicfEponUniMultActVlan	Integer32
	hpnicfEponUniMultActAddress	IpAddress
	hpnicfEponUniMultActAccessRule	INTEGER
	hpnicfEponUniMultActPreTimes	Integer32
	hpnicfEponUniMultActPreRemain	Integer32

HpnicfEponUniMulticastIndexNextEntry
SEQUENCE
	hpnicfEponUniMulticastConfIndexNext	Integer32

Defined Values

hpnicfEponUni		1.3.6.1.4.1.11.2.14.11.15.2.42.5
The objects in this MIB module are used to manage and display current configuration of UNI (user network interface) which is based on the ONU(Optical Network Unit).
MODULE-IDENTITY

hpnicfEponUniSysMan		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1
OBJECT IDENTIFIER

hpnicfEponUniSysManTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1
This table defines several UNI system parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniSysManEntry

hpnicfEponUniSysManEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1
The entry of hpnicfEponUniSysManTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniSysManEntry

hpnicfEponUniIndex		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.1
The index value which uniquely identifies the FE(fast Ethernet) interface of the ONU.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hpnicfEponUniDescr		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.2
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware and software.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hpnicfEponUniAdminStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.3
The desired state of the user network interface. When a managed system initializes, all user network interfaces start with down(2) state. The testing(3)state indicates that no operational packets can be passed. As a result of either explicit management action or per configuration information retained by the managed system, hpnicfEponUniAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

hpnicfEponUniMdi		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.4
Type of the line connected to UNI interface: mdi-ii(straight-through cable), mdi-x (crossover cable), mdi-auto (auto-sensing).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mdi-ii(1), mdi-x(2), mdi-auto(3)

hpnicfEponUniPriority		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.5
The priority of user network interface. If the value is larger, the priority will be higher.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

hpnicfEponUniVlanType		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.6
UNI vlan types.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	vlantrunk(1), access(2), hybrid(3), untagged(4), transparent(5), doubletagged(6), tag(7), translation(8)

hpnicfEponUniAccessVlan		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.7
The vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

hpnicfEponUniTrunkPvid		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.8
PVID(port vlan ID), the vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4094

hpnicfEponUniVLANTrunkAllowListLow		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.9
Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans. the vlan is not allowed if its bit has a value of '0'.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

hpnicfEponUniVLANTrunkAllowListHigh		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.10
Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 2049 through 2056, the second octet specifying vlans 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered vlan, and the least significant bit represents the lowest numbered vlan. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans; the vlan is not allowed if its bit has a value of '0'.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

hpnicfEponUniInboundLineRate		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.11
The value of the inbound line-rate. measured with kbps. The upper limit of the line-rate is the value of hpnicfEponUniLineRateMax in the entry. It must be multiple of the value of hpnicfEponUniLineRateStep. The default value of hpnicfEponUniLineRate is the value of hpnicfEponUniLineRateMax.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniOutboundLineRate		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.12
The value of the outbound line-rate. measured with kbps. The upper limit of the line-rate is the value of hpnicfEponUniLineRateMax in the entry. It must be multiple of the value of hpnicfEponUniLineRateStep. The default value of hpnicfEponUniLineRate is the value of hpnicfEponUniLineRateMax.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniFlowControl		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.13
Flow control status. true(1) - Flow control status enable. false(2) - Flow control status disable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hpnicfEponUniSpeed		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.14
User network interface speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(0), s10M(10), s100M(100), s1000M(1000), s10000M(10000), s24000M(24000)

hpnicfEponUniDuplex		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.15
User network interface mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), half(2), auto(3)

hpnicfEponUniVlanVPNStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.16
vlan VPN status. true(1) - vlan VPN status enable. false(2) - vlan VPN disable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hpnicfEponUniCountReset		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.17
Reset the counter which is about packets of the interface, then the counter will change to zero. There is no sense in reading this object.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

hpnicfEponUniPortIsolate		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.18
enable - enable UNI port isolate setting. disable - disable UNI port isolate setting.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hpnicfEponUniVlanConfiguration		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.23
The vlan configuration of the related vlan mode. Transparent vlan mode: hpnicfEponUniVlanConfiguration is a zero length string. Tag vlan mode: the first four octets were the tag assigned to untagged frames received on UNI, including TPID, VID,CFI and priority. Translation vlan mode: the first four octets were the old tag (including TPID, VID, CFI and priority), which is replaced by the new tag(including TPID, VID, CFI and priority), the second four octets.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hpnicfEponUniAutoNegotiation		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.25
enable - enable auto negotiation. disable - disable auto negotiation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hpnicfEponUniRestartAutoNeg		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.26
Force to restart the auto negotiation process.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	autoNegotiation(1)

hpnicfEponUniLinkStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.29
The link status of UNI.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

hpnicfEponUniInterfaceType		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.30
UNI interface type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	gigabitethernetport(1), fastethernetport(2), voipport(3), e1port(4)

hpnicfEponUniVitualCableTest		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.31
True(1): Virtual cable test enable. False(2): Virtual cable test disable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	true(1), false(2)

hpnicfEponUniVCTCableStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.32
Get the cable status. Normal(1),cable is normal. Abnormal(2),cable is abnormal. AbnormalOpen(3),cable is abnormal because of open circuit. AbnormalShort(4),cable is abnormal because of short circuit. Failure(5),cable is abnormal because of testing failure.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), abnormal(2), abnormalOpen(3), abnormalShort(4), failure(5)

hpnicfEponUniVCTCableLength		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.33
Get the cable length. When hpnicfEponUniVCTCableStatus is normal, the node stands for the length from the UNI port to the port opposite. When hpnicfEponUniVCTCableStatus is abnormal, it stands for the lengh from the UNI port to the failure place. Unit:meter(m).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniVCTImpedanceMismatch		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.34
Get the cable impedance. Not-support(1),the UNI port does not support this function. True(2),impedance match. False(3),impedance mismatch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-support(1), true(2), false(3)

hpnicfEponUniVCTPairSkew		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.35
Get the symmetry of cable. If the function is not supported, the default value 0 will be returned. Unit:nanosecond(ns).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniVCTPairSwap		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.36
NotSupport(1),the UNI port does not support this function. True(2),pair swap. False(3),not pair swap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupport(1), true(2), false(3)

hpnicfEponUniVCTPolaritySwap		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.37
NotSupport(1),the UNI port does not support this function. True(2),polarity swap. False(3),not polarity swap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupport(1), true(2), false(3)

hpnicfEponUniVCTInsertionLoss		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.38
If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniVCTReturnLoss		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.39
If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniVCTNearendCrosstalk		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.40
If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniVlan		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.41
If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hpnicfEponUniCountTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2
A list of interface counter about frames entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniCountEntry

hpnicfEponUniCountEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1
An entry containing management information applicable to a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniCountEntry

hpnicfEponUniInStatsPkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.1
The total number of frames (including bad frames, broadcast frames, and multicast frames) received.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInStatsUnicastPkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.2
The total number of good frames received that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInStatsBroadcastPkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.3
The total number of good frames received that are directed to the broadcast address. Note that this does not include multicast frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInStatsMulticastPkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.4
The total number of good frames received that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInPausePkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.5
A count of MAC Control frames received on this interface by the pause(flow control) operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInTotalErrors		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.6
Total count of the error frames received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInStatsCRCAlignErrors		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.7
The total number of frames received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInStatsUndersizePkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.8
The total number of frames received that are less than 64 octets long (excluding framing bits, but including FCS octets) and are otherwise well formed.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInStatsOversizePkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.9
The total number of frames received that are longer than 1518 octets (excluding framing bits, but including FCS octets) and are otherwise well formed.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniInErrorbyOther		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.10
The total number of error frames received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutStatsPkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.11
The total number of frames (including bad frames, broadcast frames, and multicast frames) sent.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutStatsUnicastPkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.12
The total number of good frames sent that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutStatsBroadcastPkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.13
The total number of good frames sent that are directed to the broadcast address. Note that this does not include multicast frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutStatsMulticastPkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.14
The total number of good frames sent that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutStatsPausePkts		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.15
The total number of MAC control frames sent on this interface by the pause operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutTotalErrors		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.16
The total number of error frames sent on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutStatsCollisions		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.17
The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment could. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutDelayExceededDiscards		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.18
The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutErrorbyOther		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.19
The total number of other error frames sent on this interface. Other error frames means the error frames out of collision frames and excessive delayed frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniOutDroppedFrames		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.20
The total number of frames dropped because of buffer failure.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hpnicfEponUniIgmpInfoTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3
This table stores igmp information of UNI interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniIgmpInfoEntry

hpnicfEponUniIgmpInfoEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3.1
The entry of hpnicfEponUniIgmpInfoTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniIgmpInfoEntry

hpnicfEponUniMacIndex		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3.1.1
The index uniquely identifies the igmp information in current UNI interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hpnicfEponUniIgmpMacAddress		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3.1.2
A 6-octet read-only value carrying the individual MAC address indicates which igmp group the UNI interface belonging to.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

hpnicfEponUniIgmpVlanId		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3.1.3
An integer range from 1 to 4094 indicates the vlan which the igmp Mac address has joined in.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

hpnicfEponUniParaMan		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.4
OBJECT IDENTIFIER

hpnicfEponUniLineRateMax		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.4.1
The maximum value of the line-rate(kbps) that user network interface can be set.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniLineRateStep		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.4.2
The step of line-rate(kbps).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniNumberOnOnu		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.4.3
The user network interface number on ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniScalarGroup		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.5
OBJECT IDENTIFIER

hpnicfEponUniPortPolicyTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6
UNI port policy configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniPortPolicyEntry

hpnicfEponUniPortPolicyEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1
The entry of hpnicfEponUniPortPolicyTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniPortPolicyEntry

hpnicfEponUniPortPolicyStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.1
enable - enable UNI upstream port policing. disable - disable UNI upstream port policing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hpnicfEponUniPortPolicyCir		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.2
The committed information rate, ranging from 1 to 102400, measured in kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniPortPolicyBucketDepth		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.3
The depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniPortPolicyExtraBurst		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.4
The extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniPortPolicyInboundCir		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.5
The inbound committed information rate, measured in kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniPortPolicyInboundBucketDepth		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.6
The inbound depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniPortPolicyInboundExtraBurst		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.7
The inbound extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniPortPolicyOutboundCir		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.8
The outbound committed information rate, stepped by 64, measured in kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniPortPolicyOutboundPir		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.9
The outbound peak information rate, stepped by 64, measured in kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7
UNI multicast configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniMulticastEntry

hpnicfEponUniMulticastEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1
The entry of hpnicfEponUniPortPolicyTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniMulticastEntry

hpnicfEponUniMulticastGroupNumber		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1.1
The allowed multicast group number that can be handled at the same time by UNI.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastVlanList		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1.2
The multicast vlan list. The first two octets of the string represent the first VLAN ID; the second two octets of the string represent the second VLAN ID, and so on. It is a zero length string by default.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hpnicfEponUniMulticastStripStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1.3
true - strip the vlan tag of multicast packet. false - does not strip the vlan tag of multicast packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hpnicfEponUniMulticastFastleave		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1.4
true(1) - fast leave of IGMP enable on ONU. false(2) - fast leave of IGMP disable on ONU.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hpnicfEponUniTechAbilityTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.8
UNI multicast configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniTechAbilityEntry

hpnicfEponUniTechAbilityEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.8.1
The entry of hpnicfEponUniTechAbilityTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniTechAbilityEntry

hpnicfEponUniLocalTechAbility		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.8.1.1
The local port capabilities of the UNI. Each two octets stand for a capability of UNI: the first two octets represent one capability and the second two octets represent another capability, and so on. The capabilities list: 1 - undefined, 2 - initializing, true ability not yet known, 14 - 10BASE-T, 142 - full duplex 10BASE-T, 23 - 100BASE-T4, 25 - 100BASE-TX, 252 - full duplex 100BASE-TX, 312 - PAUSE operation for full duplex links, 313 - asymmetric PAUSE operation for full duplex links, 314 - symmetric PAUSE operation for full duplex links, 32 - 100BASE-T2, 322 - full duplex 100BASE-T2, 36 - 1000BASE-X, 362 - full duplex 1000BASE-X, 40 - 1000BASE-T UTP PHY, 402 - full duplex 1000BASE-T UTP PHY, 37 - remote fault bit 1(RF1), 372 - remote fault bit 2(RF2), 8029 - 802.9ISLAN-16T.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hpnicfEponUniAdvertisedTechAbility		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.8.1.2
The advertised port capabilities of the UNI. The capabilities list references the description of hpnicfEponUniLocalTechAbility.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hpnicfEponUniMulticastControlTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9
UNI multicast control parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniMulticastControlEntry

hpnicfEponUniMulticastControlEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1
The entry of the table hpnicfEponUniMulticastControlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniMulticastControlEntry

hpnicfEponUniMulticastVlanIndex		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.1
The multicast vlan ID.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastAddressList		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.2
The multicast address, each four octets represents a multicast address, the address section ranging from the first four octets to the second four octets, and the like.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hpnicfEponUniMulticastAccessRule		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.3
deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	deny(1), permit(2), preview(3)

hpnicfEponUniMulticastChannelLimit		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.4
The limitation of multicast preview channel number.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastPreTimeSlice		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.5
The time slice of multicast preview.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastPreTimes		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.6
The number of multicast preview times.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastPreInterval		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.7
The interval between two consecutive previews, measured in minute.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastRowStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.8
The status of this table entry. The active, createAndGo and the destory statuses are supported.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hpnicfEponUniMulticastIndex		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.9
The index of the entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

hpnicfEponUniMulticastSourceIpList		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.10
This list contains many source ip addresses. Each ip address is contained in four octets.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hpnicfEponUniMulticastResetInterval		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.11
The interval is measured in minute. From the last preview limitation is reached, a customer can preview again after this interval is expired.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniQosIndexNextTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.10
The next index table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniQosIndexNextEntry

hpnicfEponUniQosIndexNextEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.10.1
The entry of the table hpnicfEponUniQosIndexNextTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniQosIndexNextEntry

hpnicfEponUniQosConfIndexNext		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.10.1.1
This object contains an appropriate value to be used for hpnicfEponUniQosConfIndex when creating rows in the hpnicfEponUniQosConfTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniQosConfTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11
UNI Qos configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniQosConfEntry

hpnicfEponUniQosConfEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1
The entry of the table hpnicfEponUniQosConfTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniQosConfEntry

hpnicfEponUniQosConfIndex		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.1
The rule index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hpnicfEponUniQosConfRuleIndexNext		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.2
This object contains an appropriate value to be used for hpnicfEponUniQosRuleIndex when creating rows in the hpnicfEponUniQosRuleTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniQosConfMappedQueue		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.3
The queue that the ethernet frames will be mapped.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniQosConfMarkedPriority		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.4
Priority of the ethernet frames to be marked, which compliant with the 802.1D user priority standard.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniQosConfRowStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.5
The status of this table entry. The active, createAndGo and the destory statuses are supported.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hpnicfEponUniQosRuleTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12
Qos sub rule of the UNI.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniQosRuleEntry

hpnicfEponUniQosRuleEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1
The entry of the table hpnicfEponUniQosRuleTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniQosRuleEntry

hpnicfEponUniQosRuleIndex		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.1
The sub rule index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

hpnicfEponUniQosRuleSelector		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.2
The ethernet frame selector. dstmac - based on destination MAC address. srcmac - based on source MAC address. ethernetpriority - based on ethernet priority. vlanid - based on VLAN ID. ethernettype - based on ethernet type. dstip - based on destination IP address. srcip - based on source IP address. ipprototype - based on IP type(ipv4 or ipv6). ipv4tosdscp - based on IP TOS/DSCP. ipv6 - based IP precedence. srcport - based on layer 4 source port. dstport - based on layer 4 destination port.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	dstmac(1), srcmac(2), ethernetpriority(3), vlanid(4), ethernettype(5), dstip(6), srcip(7), ipprototype(8), ipv4tosdscp(9), ipv6precedence(10), srcport(11), dstport(12)

hpnicfEponUniQosRuleValue		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.3
The rule value based on the hpnicfEponUniQosRuleSelector.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniQosRuleMacAddress		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.4
MAC Address.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

hpnicfEponUniQosRuleOperator		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.5
nervermatch - value never match. equal - field equal to the value. notequal - field not equal to the value. lessthanequal - field less than or equal to the value. greaterthanequal - field greater than or equal to the value. fieldexist - value is ignored if field exists. fieldnotexist - value is ignored if field does not exist. alwaysmatch - value always match.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	nevermatch(1), equal(2), notequal(3), lessthanequal(4), greaterthanequal(5), fieldexist(6), fieldnotexist(7), alwaysmatch(8)

hpnicfEponUniQosRuleRowStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.6
The status of this table entry. Only active, createAndGo and the destory are supported.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hpnicfEponUniMirrorGroupTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13
Qos sub rule of the UNI.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniMirrorGroupEntry

hpnicfEponUniMirrorGroupEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1
The entry of the hpnicfEponUniMirrorGroupTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniMirrorGroupEntry

hpnicfEponUniMirrorGroupID		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.1
Epon UNI mirror group ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hpnicfEponUniMirrorInboundPortList		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.2
UNI inbound port list. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered UNI, and the least significant bit represents the lowest numbered UNI. Thus, each UNI port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is allowed in the set of ports. the port is not allowed if its bit has a value of '0'.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

hpnicfEponUniMirrorOutboundPortList		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.3
UNI outnbound port list, more infomation reference hpnicfEponUniMirrorInboundPortList
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

hpnicfEponUniMonitorPort		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.4
UNI monitor port.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hpnicfEponUniMirrorRowStatus		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.5
RowStatus, Now support three status: createAndGo, active, destroy.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hpnicfEponUniMirrorGroupIdNextTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.14
The next index table, which is used by hpnicfEponUniMirrorGroupTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniMirrorGroupIdNextEntry

hpnicfEponUniMirrorGroupIdNextEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.14.1
The entry of the table hpnicfEponUniMirrorGroupIdNextEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniMirrorGroupIdNextEntry

hpnicfEponUniMirrorGroupIDNext		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.14.1.1
This object contains an appropriate value to be used for hpnicfEponUniMirrorGroupID when creating rows in the hpnicfEponUniMirrorGroupTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastCtrlInfoTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15
UNI multicast information which is active .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniMulticastCtrlInfoEntry

hpnicfEponUniMulticastCtrlInfoEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1
The entry of the table hpnicfEponUniMulticastCtrlInfoTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniMulticastCtrlInfoEntry

hpnicfEponUniMultActVlan		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.1
The multicast vlan ID which is active.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hpnicfEponUniMultActAddress		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.2
The multicast address which is active.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

hpnicfEponUniMultActAccessRule		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.3
deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	deny(1), permit(2), preview(3)

hpnicfEponUniMultActPreTimes		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.4
The number of multicast preview times which is active.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniMultActPreRemain		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.5
The remanent time slice of multicast preview which is active.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniMulticastIndexNextTable		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.16
The next index table, which is used by hpnicfEponUniMulticastControlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HpnicfEponUniMulticastIndexNextEntry

hpnicfEponUniMulticastIndexNextEntry		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.16.1
The entry of the table hpnicfEponUniMulticastIndexNextEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	HpnicfEponUniMulticastIndexNextEntry

hpnicfEponUniMulticastConfIndexNext		1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.16.1.1
This object contains an appropriate value to be used for hpnicfEponUniMulticastIndex when creating rows in the hpnicfEponUniMulticastControlTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hpnicfEponUniTrap		1.3.6.1.4.1.11.2.14.11.15.2.42.5.2
OBJECT IDENTIFIER

hpnicfEponUniTrapPrefix		1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0
OBJECT IDENTIFIER

hpnicfEponUniLinkUpTrap		1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0.1
A hpnicfEponUniLinkUpTrap notification is sent when the UNI up event is detected and the transmitting switch is turned on.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfEponUniLinkDownTrap		1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0.2
A hpnicfEponUniLinkDownTrap notification is sent when the UNI down event is detected and the transmitting switch is turned on.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfEponUniLoopBackDetectedTrap		1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0.3
A hpnicfEponUniLoopBackDetectedTrap notification is sent when the UNI loopback event is detected.
Status: current	Access: read-only
NOTIFICATION-TYPE

hpnicfEponUniLoopBackRecoveredTrap		1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0.4
A hpnicfEponUniLoopBackRecoveredTrap notification is sent when the UNI loopback is recovered.
Status: current	Access: read-only
NOTIFICATION-TYPE