HP-SN-MPLS-LSR-MIB

File: HP-SN-MPLS-LSR-MIB.mib (63388 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
IF-MIB	HP-SN-MPLS-TC-MIB	IANA-ADDRESS-FAMILY-NUMBERS-MIB
INET-ADDRESS-MIB	FOUNDRY-SN-ROOT-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	Counter32	Unsigned32
Counter64	Gauge32	MODULE-COMPLIANCE
OBJECT-GROUP	NOTIFICATION-GROUP	TruthValue
RowStatus	StorageType	RowPointer
TimeStamp	InterfaceIndex	InterfaceIndexOrZero
mplsMIB	MplsLSPID	MplsLabel
MplsBitRate	MplsBurstSize	MplsInitialCreationSource
AddressFamilyNumbers	InetAddressIPv4	InetAddressIPv6
InetAddressType	snMpls

Defined Types

MplsInterfaceConfEntry
SEQUENCE
	mplsInterfaceConfIndex	InterfaceIndexOrZero
	mplsInterfaceLabelMinIn	MplsLabel
	mplsInterfaceLabelMaxIn	MplsLabel
	mplsInterfaceLabelMinOut	MplsLabel
	mplsInterfaceLabelMaxOut	MplsLabel
	mplsInterfaceTotalBandwidth	MplsBitRate
	mplsInterfaceAvailableBandwidth	MplsBitRate
	mplsInterfaceLabelParticipationType	BITS

MplsInterfacePerfEntry
SEQUENCE
	mplsInterfaceInLabelsUsed	Gauge32
	mplsInterfaceFailedLabelLookup	Counter32
	mplsInterfaceOutLabelsUsed	Gauge32
	mplsInterfaceOutFragments	Counter32

MplsInSegmentEntry
SEQUENCE
	mplsInSegmentIfIndex	InterfaceIndexOrZero
	mplsInSegmentLabel	MplsLabel
	mplsInSegmentNPop	Integer32
	mplsInSegmentAddrFamily	AddressFamilyNumbers
	mplsInSegmentXCIndex	Unsigned32
	mplsInSegmentOwner	MplsInitialCreationSource
	mplsInSegmentTrafficParamPtr	RowPointer
	mplsInSegmentRowStatus	RowStatus
	mplsInSegmentStorageType	StorageType

MplsInSegmentPerfEntry
SEQUENCE
	mplsInSegmentOctets	Counter32
	mplsInSegmentPackets	Counter32
	mplsInSegmentErrors	Counter32
	mplsInSegmentDiscards	Counter32
	mplsInSegmentHCOctets	Counter64
	mplsInSegmentPerfDiscontinuityTime	TimeStamp

MplsOutSegmentEntry
SEQUENCE
	mplsOutSegmentIndex	Unsigned32
	mplsOutSegmentIfIndex	InterfaceIndexOrZero
	mplsOutSegmentPushTopLabel	TruthValue
	mplsOutSegmentTopLabel	MplsLabel
	mplsOutSegmentNextHopIpAddrType	InetAddressType
	mplsOutSegmentNextHopIpv4Addr	InetAddressIPv4
	mplsOutSegmentNextHopIpv6Addr	InetAddressIPv6
	mplsOutSegmentXCIndex	Unsigned32
	mplsOutSegmentOwner	MplsInitialCreationSource
	mplsOutSegmentTrafficParamPtr	RowPointer
	mplsOutSegmentRowStatus	RowStatus
	mplsOutSegmentStorageType	StorageType

MplsOutSegmentPerfEntry
SEQUENCE
	mplsOutSegmentOctets	Counter32
	mplsOutSegmentPackets	Counter32
	mplsOutSegmentErrors	Counter32
	mplsOutSegmentDiscards	Counter32
	mplsOutSegmentHCOctets	Counter64
	mplsOutSegmentPerfDiscontinuityTime	TimeStamp

MplsXCEntry
SEQUENCE
	mplsXCIndex	Unsigned32
	mplsXCLspId	MplsLSPID
	mplsXCLabelStackIndex	Unsigned32
	mplsXCIsPersistent	TruthValue
	mplsXCOwner	MplsInitialCreationSource
	mplsXCRowStatus	RowStatus
	mplsXCStorageType	StorageType
	mplsXCAdminStatus	INTEGER
	mplsXCOperStatus	INTEGER

MplsLabelStackEntry
SEQUENCE
	mplsLabelStackIndex	Unsigned32
	mplsLabelStackLabelIndex	Unsigned32
	mplsLabelStackLabel	MplsLabel
	mplsLabelStackRowStatus	RowStatus
	mplsLabelStackStorageType	StorageType

MplsTrafficParamEntry
SEQUENCE
	mplsTrafficParamIndex	Unsigned32
	mplsTrafficParamMaxRate	MplsBitRate
	mplsTrafficParamMeanRate	MplsBitRate
	mplsTrafficParamMaxBurstSize	MplsBurstSize
	mplsTrafficParamRowStatus	RowStatus
	mplsTrafficParamStorageType	StorageType

Defined Values

mplsLsrMIB		1.3.6.1.4.1.1991.1.2.15.15.2
This MIB contains managed object definitions for the Multiprotocol Label Switching (MPLS) Router as defined in: Rosen, E., Viswanathan, A., and R. Callon, Multiprotocol Label Switching Architecture, RFC 3031, January 2001.
MODULE-IDENTITY

mplsLsrObjects		1.3.6.1.4.1.1991.1.2.15.15.2.1
OBJECT IDENTIFIER

mplsLsrNotifications		1.3.6.1.4.1.1991.1.2.15.15.2.2
OBJECT IDENTIFIER

mplsLsrNotifyPrefix		1.3.6.1.4.1.1991.1.2.15.15.2.2.0
OBJECT IDENTIFIER

mplsLsrConformance		1.3.6.1.4.1.1991.1.2.15.15.2.3
OBJECT IDENTIFIER

mplsInterfaceConfTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.1
This table specifies per-interface MPLS capability and associated information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsInterfaceConfEntry

mplsInterfaceConfEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1
An entry in this table is created by an LSR for every interface capable of supporting MPLS. Each entry in this table will exist only if a corresponding entry in ifTable exists. If the associated entry in ifTable is deleted, the corresponding entry in this table must also be deleted shortly thereafter. The entry with index 0 represents the per-platform label space and contains parameters that apply to all interfaces that participate in the per-platform label space. Other entries defined in this table represent additional MPLS interfaces that may participate in either the per-platform or per-interface label spaces, or both. Additional information about label space participation of an interface is provided in the description clause of mplsInterfaceLabelParticipationType.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsInterfaceConfEntry

mplsInterfaceConfIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1.1
This is a unique index for an entry in the MplsInterfaceConfTable. A non-zero index for an entry indicates the ifIndex for the corresponding interface entry in of the MPLS-layer in the ifTable. Note that the per-platform label space may apply to several interfaces, and therefore the configuration of the per-platform label space interface parameters will apply to all of the interfaces that are participating in the per-platform label space.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndexOrZero

mplsInterfaceLabelMinIn		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1.2
This is the minimum value of an MPLS label that this LSR is willing to receive on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

mplsInterfaceLabelMaxIn		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1.3
This is the maximum value of an MPLS label that this LSR is willing to receive on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

mplsInterfaceLabelMinOut		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1.4
This is the minimum value of an MPLS label that this LSR is willing to send on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

mplsInterfaceLabelMaxOut		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1.5
This is the maximum value of an MPLS label that this LSR is willing to send on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

mplsInterfaceTotalBandwidth		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1.6
This value indicates the total amount of usable bandwidth on this interface and is specified in kilobits per second (Kbps). This variable is not applicable when applied to the interface with index 0. When this value cannot be measured, this value should contain the nominal bandwidth.
Status: current	Access: read-only
OBJECT-TYPE
	MplsBitRate

mplsInterfaceAvailableBandwidth		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1.7
This value indicates the total amount of available bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use and that specified in mplsInterfaceTotalBandwidth. This variable is not applicable when applied to the interface with index 0. When this value cannot be measured, this value should contain the nominal bandwidth.
Status: current	Access: read-only
OBJECT-TYPE
	MplsBitRate

mplsInterfaceLabelParticipationType		1.3.6.1.4.1.1991.1.2.15.15.2.1.1.1.8
Either the perPlatform(0) or perInterface(1) bit MUST be set. If the value of the mplsInterfaceConfIndex for this entry is zero, then only the perPlatform(0) bit MUST be set and the perInterface(1) bit is meaningless. If the perInterface(1) bit is set then the value of mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn, mplsInterfaceLabelMinOut, and mplsInterfaceLabelMaxOut for this entry reflect the label ranges for this interface. If only the perPlatform(0) bit is set, then the value of mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn, mplsInterfaceLabelMinOut, and mplsInterfaceLabelMaxOut for this entry must be identical to the instance of these objects with index 0.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	perPlatform(0), perInterface(1)

mplsInterfacePerfTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.2
This table provides MPLS performance information on a per-interface basis.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsInterfacePerfEntry

mplsInterfacePerfEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.2.1
An entry in this table is created by the LSR for every interface capable of supporting MPLS. Its is an extension to the mplsInterfaceConfEntry table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsInterfacePerfEntry

mplsInterfaceInLabelsUsed		1.3.6.1.4.1.1991.1.2.15.15.2.1.2.1.1
This object counts the number of labels that are in use at this point in time on this interface in the incoming direction. If the interface participates in the per-platform label space only, then this instance of this object MUST be identical with the instance with index 0. If the interface participates in the per-interface label space, then this instance of this object MUST represent the number of of per- interface labels that are in use at this point in time on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

mplsInterfaceFailedLabelLookup		1.3.6.1.4.1.1991.1.2.15.15.2.1.2.1.2
This object counts the number of labeled packets that have been received on this interface and were discarded because there was no matching cross- connect entry. This object MUST count on a per- interface basis regardless of which label space the interface participates in.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsInterfaceOutLabelsUsed		1.3.6.1.4.1.1991.1.2.15.15.2.1.2.1.3
This object counts the number of top-most labels in the outgoing label stacks that are in use at this point in time on this interface. This object MUST count on a per-interface basis regardless of which label space the interface participates in.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

mplsInterfaceOutFragments		1.3.6.1.4.1.1991.1.2.15.15.2.1.2.1.4
This object counts the number of outgoing MPLS packets that required fragmentation before transmission on this interface. This object MUST count on a per-interface basis regardless of which label space the interface participates in.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsInSegmentTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.3
This table contains a collection of incoming segments to an LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsInSegmentEntry

mplsInSegmentEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1
An entry in this table represents one incoming segment. An entry can be created by a network administrator or an SNMP agent, or an MPLS signaling protocol. The creator of the entry is denoted by mplsInSegmentOwner. An entry in this table is indexed by the ifIndex of the incoming interface and the (top) label. The value of mplsInSegmentRowStatus cannot be active(1)unless the ifTable entry corresponding to mplsInSegmentIfIndex exists.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsInSegmentEntry

mplsInSegmentIfIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.1
This is a unique index for an entry in the MplsInSegmentTable. This value represents the interface index for the incoming MPLS interface. A value of zero represents an incoming label from the per-platform label space. In this case, the mplsInSegmentLabel is interpreted to be an MPLS-type label.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndexOrZero

mplsInSegmentLabel		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.2
The incoming label for this segment.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLabel

mplsInSegmentNPop		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.3
The number of labels to pop from the incoming packet. Normally only the top label is popped from the packet and used for all switching decisions for that packet. Note that technologies which do not support label popping should set this value to its default value of 1. This object cannot be modified if mplsInSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..2147483647

mplsInSegmentAddrFamily		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.4
The IANA address family [IANAFamily] of the incoming packet. A value of other(0) indicates that the family type is either unknown or undefined. This object cannot be modified if mplsInSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	AddressFamilyNumbers

mplsInSegmentXCIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.5
Index into mplsXCTable which identifies which cross- connect entry this segment is part of. A value of zero indicates that this entry is not referred to by any cross-connect entry. When a cross-connect entry is created which this in-segment is a part of, this object is automatically updated to reflect the value of mplsXCIndex of that cross-connect entry.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

mplsInSegmentOwner		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.6
Denotes the entity that created and is responsible for managing this segment. This object cannot be modified if mplsInSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	MplsInitialCreationSource

mplsInSegmentTrafficParamPtr		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.7
This variable represents a pointer to the traffic parameter specification for this in-segment. This value may point at an entry in the mplsTrafficParamTable to indicate which mplsTrafficParamEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zero-dot-zero indicates best-effort treatment. By having the same value of this object, two or more segments can indicate resource sharing. This object cannot be modified if mplsInSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowPointer

mplsInSegmentRowStatus		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.8
This variable is used to create, modify, and/or delete a row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

mplsInSegmentStorageType		1.3.6.1.4.1.1991.1.2.15.15.2.1.3.1.9
This variable indicates the storage type for this object. This object cannot be modified if mplsInSegmentRowStatus is active(1). If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

mplsInSegmentPerfTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.4
This table contains statistical information for incoming MPLS segments to an LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsInSegmentPerfEntry

mplsInSegmentPerfEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.4.1
An entry in this table contains statistical information about one incoming segment which was configured in the mplsInSegmentTable. The counters in this entry should behave in a manner similar to that of the interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsInSegmentPerfEntry

mplsInSegmentOctets		1.3.6.1.4.1.1991.1.2.15.15.2.1.4.1.1
This value represents the total number of octets received by this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsInSegmentPackets		1.3.6.1.4.1.1991.1.2.15.15.2.1.4.1.2
Total number of packets received by this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsInSegmentErrors		1.3.6.1.4.1.1991.1.2.15.15.2.1.4.1.3
The number of errored packets received on this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsInSegmentDiscards		1.3.6.1.4.1.1991.1.2.15.15.2.1.4.1.4
The number of labeled packets received on this in- segment, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsInSegmentHCOctets		1.3.6.1.4.1.1991.1.2.15.15.2.1.4.1.5
The total number of octets received. This is the 64 bit version of mplsInSegmentOctets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

mplsInSegmentPerfDiscontinuityTime		1.3.6.1.4.1.1991.1.2.15.15.2.1.4.1.6
The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

mplsOutSegmentIndexNext		1.3.6.1.4.1.1991.1.2.15.15.2.1.5
This object contains the next appropriate value to be used for mplsOutSegmentIndex when creating entries in the mplsOutSegmentTable. If the number of unassigned entries is exhausted, this object will take on the value of 0. To obtain the mplsOutSegmentIndex value for a new entry, the manager must first issue a management protocol retrieval operation to obtain the current value of this object. The agent should modify the value to reflect the next unassigned index after each retrieval operation. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

mplsOutSegmentTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.6
This table contains a representation of the outgoing segments from an LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsOutSegmentEntry

mplsOutSegmentEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1
An entry in this table represents one outgoing segment. An entry can be created by a network administrator or an SNMP agent, or an MPLS signaling protocol. The object mplsOutSegmentOwner indicates the creator of this entry. The value of mplsOutSegmentRowStatus cannot be active(1)unless the ifTable entry corresponding to mplsOutSegmentIfIndex exists.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsOutSegmentEntry

mplsOutSegmentIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.1
This value contains a unique index for this row. While a value of 0 is not valid as an index for this row it can be supplied as a valid value to index mplsXCTable to access entries for which no out- segment has been configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..2147483647

mplsOutSegmentIfIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.2
This value must contain the interface index of the outgoing interface. This object may only take the value of 0 during the create-and-wait row creation operation if the management station has not yet set the value of this object. This object cannot be modified if mplsOutSegmentRowStatus is active(1). The mplsOutSegmentRowStatus cannot be set to active(1) until this object is set to a value corresponding to a valid ifEntry.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

mplsOutSegmentPushTopLabel		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.3
This value indicates whether or not a top label should be pushed onto the outgoing packet's label stack. The value of this variable MUST be set to true if the outgoing interface does not support pop- and-go (for example an ATM interface) or if it is a tunnel origination. Note that it is considered an error in the case that mplsOutSegmentPushTopLabel is set to false, but the cross-connect entry which refers to this out-segment has a non-zero mplsLabelStackIndex. The LSR MUST ensure that this situation does not happen. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

mplsOutSegmentTopLabel		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.4
If mplsOutSegmentPushTopLabel is true then this represents the label that should be pushed onto the top of the outgoing packet's label stack. Otherwise this value SHOULD be set to 0 by the management station and MUST be ignored by the agent. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	MplsLabel

mplsOutSegmentNextHopIpAddrType		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.5
Indicates whether the next hop address is IPv4 or IPv6. Note that a value of unknown (0) is valid only when the outgoing interface is of type point-to- point. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

mplsOutSegmentNextHopIpv4Addr		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.6
IPv4 Address of the next hop. Its value is significant only when mplsOutSegmentNextHopIpAddrType is ipV4 (1), otherwise it SHOULD return a value of 0. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressIPv4

mplsOutSegmentNextHopIpv6Addr		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.7
IPv6 address of the next hop. Its value is significant only when mplsOutSegmentNextHopIpAddrType is ipV6 (2), otherwise it SHOULD return a value of 0. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressIPv6

mplsOutSegmentXCIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.8
Index into mplsXCTable which identifies which cross- connect entry this segment is part of. A value of zero indicates that this entry is not referred to by any cross-connect entry. When a cross-connect entry is created which this out-segment is a part of, this object is automatically updated to reflect the value of mplsXCIndex of that cross-connect entry.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

mplsOutSegmentOwner		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.9
Denotes the entity which created and is responsible for managing this segment. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	MplsInitialCreationSource

mplsOutSegmentTrafficParamPtr		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.10
This variable represents a pointer to the traffic parameter specification for this out-segment. This value may point at an entry in the mplsTrafficParamTable to indicate which mplsTrafficParamEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zero-dot-zero indicates best- effort treatment. By having the same value of this object, two or more segments can indicate resource sharing. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowPointer

mplsOutSegmentRowStatus		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.11
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

mplsOutSegmentStorageType		1.3.6.1.4.1.1991.1.2.15.15.2.1.6.1.12
This variable indicates the storage type for this object. This object cannot be modified if mplsOutSegmentRowStatus is active(1). If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

mplsOutSegmentPerfTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.7
This table contains statistical information about outgoing segments from an LSR. The counters in this entry should behave in a manner similar to that of the interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsOutSegmentPerfEntry

mplsOutSegmentPerfEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.7.1
An entry in this table contains statistical information about one outgoing segment configured in mplsOutSegmentTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsOutSegmentPerfEntry

mplsOutSegmentOctets		1.3.6.1.4.1.1991.1.2.15.15.2.1.7.1.1
This value contains the total number of octets sent on this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsOutSegmentPackets		1.3.6.1.4.1.1991.1.2.15.15.2.1.7.1.2
This value contains the total number of packets sent on this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsOutSegmentErrors		1.3.6.1.4.1.1991.1.2.15.15.2.1.7.1.3
Number of packets that could not be sent due to errors on this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsOutSegmentDiscards		1.3.6.1.4.1.1991.1.2.15.15.2.1.7.1.4
The number of labeled packets received on this out- segment, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

mplsOutSegmentHCOctets		1.3.6.1.4.1.1991.1.2.15.15.2.1.7.1.5
Total number of octets sent. This is the 64 bit version of mplsOutSegmentOctets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

mplsOutSegmentPerfDiscontinuityTime		1.3.6.1.4.1.1991.1.2.15.15.2.1.7.1.6
The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

mplsXCIndexNext		1.3.6.1.4.1.1991.1.2.15.15.2.1.8
This object contains an appropriate value to be used for mplsXCIndex when creating entries in the mplsXCTable. The value 0 indicates that no unassigned entries are available. To obtain the value of mplsXCIndex for a new entry in the mplsXCTable, the manager issues a management protocol retrieval operation to obtain the current value of mplsXCIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

mplsXCTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.9
This table specifies information for switching between LSP segments. It supports point-to-point, point-to-multipoint and multipoint-to-point connections. mplsLabelStackTable specifies the label stack information for a cross-connect LSR and is referred to from mplsXCTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsXCEntry

mplsXCEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1
A row in this table represents one cross-connect entry. The following objects index it: - cross-connect index mplsXCIndex that uniquely identifies a group of cross-connect entries - interface index of the in-segment, mplsInSegmentIfIndex - incoming label(s), mplsInSegmentLabel - out-segment index, mplsOutSegmentIndex Originating LSPs: These are represented by using the special combination of values mplsInSegmentIfIndex=0 and mplsInSegmentLabel=0 as indexes. In this case the mplsOutSegmentIndex MUST be non-zero. Terminating LSPs: These are represented by using the special value mplsOutSegmentIndex=0 as index. Special labels: Entries indexed by reserved MPLS label values 0 through 15 imply terminating LSPs and MUST have mplsOutSegmentIfIndex = 0. Note that situations where LSPs are terminated with incoming label equal to 0, should have mplsInSegmentIfIndex = 0 as well, but can be distinguished from originating LSPs because the mplsOutSegmentIfIndex = 0. The mplsOutSegmentIfIndex MUST only be set to 0 in cases of terminating LSPs. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsXCEntry

mplsXCIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.1
Primary index for the conceptual row identifying a group of cross-connect segments.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..2147483647

mplsXCLspId		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.2
This value identifies the label switched path that this cross-connect entry belongs to. This object cannot be modified if mplsXCRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	MplsLSPID

mplsXCLabelStackIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.3
Primary index into mplsLabelStackTable identifying a stack of labels to be pushed beneath the top label. Note that the top label identified by the out- segment ensures that all the components of a multipoint-to-point connection have the same outgoing label. A value of 0 indicates that no labels are to be stacked beneath the top label. This object cannot be modified if mplsXCRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4294967295

mplsXCIsPersistent		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.4
Denotes whether or not this cross-connect entry and associated in- and out-segments should be restored automatically after failures. This value MUST be set to false in cases where this cross-connect entry was created by a signaling protocol. This object cannot be modified if mplsXCRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

mplsXCOwner		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.5
Denotes the entity that created and is responsible for managing this cross-connect. This object cannot be modified if mplsXCRowStatus is active(1).
Status: current	Access: read-create
OBJECT-TYPE
	MplsInitialCreationSource

mplsXCRowStatus		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.6
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

mplsXCStorageType		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.7
Defines the storage type for this object. This object cannot be modified if mplsXCRowStatus is active(1). If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

mplsXCAdminStatus		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.8
The desired operational status of this segment.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

mplsXCOperStatus		1.3.6.1.4.1.1991.1.2.15.15.2.1.9.1.9
The actual operational status of this cross- connect.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), unknown(4), dormant(5), notPresent(6), lowerLayerDown(7)

mplsMaxLabelStackDepth		1.3.6.1.4.1.1991.1.2.15.15.2.1.10
The maximum stack depth supported by this LSR.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

mplsLabelStackIndexNext		1.3.6.1.4.1.1991.1.2.15.15.2.1.11
This object contains an appropriate value to be used for mplsLabelStackIndex when creating entries in the mplsLabelStackTable. The value 0 indicates that no unassigned entries are available. To obtain an mplsLabelStackIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

mplsLabelStackTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.12
This table specifies the label stack to be pushed onto a packet, beneath the top label. Entries into this table are referred to from mplsXCTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsLabelStackEntry

mplsLabelStackEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.12.1
An entry in this table represents one label which is to be pushed onto an outgoing packet, beneath the top label. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLabelStackEntry

mplsLabelStackIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.12.1.1
Primary index for this row identifying a stack of labels to be pushed on an outgoing packet, beneath the top label.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..2147483647

mplsLabelStackLabelIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.12.1.2
Secondary index for this row identifying one label of the stack. Note that an entry with a smaller mplsLabelStackLabelIndex would refer to a label higher up the label stack and would be popped at a downstream LSR before a label represented by a higher mplsLabelStackLabelIndex at a downstream LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..2147483647

mplsLabelStackLabel		1.3.6.1.4.1.1991.1.2.15.15.2.1.12.1.3
The label to pushed.
Status: current	Access: read-create
OBJECT-TYPE
	MplsLabel

mplsLabelStackRowStatus		1.3.6.1.4.1.1991.1.2.15.15.2.1.12.1.4
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

mplsLabelStackStorageType		1.3.6.1.4.1.1991.1.2.15.15.2.1.12.1.5
Defines the storage type for this object. If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

mplsTrafficParamIndexNext		1.3.6.1.4.1.1991.1.2.15.15.2.1.13
This object contains an appropriate value which will be used for mplsTrafficParamIndex when creating entries in the mplsTrafficParamTable. The value 0 indicates that no unassigned entries are available. To obtain the mplsTrafficParamIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

mplsTrafficParamTable		1.3.6.1.4.1.1991.1.2.15.15.2.1.14
This table specifies the Traffic Parameter objects for in and out-segments.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MplsTrafficParamEntry

mplsTrafficParamEntry		1.3.6.1.4.1.1991.1.2.15.15.2.1.14.1
An entry in this table represents the TrafficParam objects for one or more in or out segments. A single entry can be pointed to by multiple segments indicating resource sharing.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsTrafficParamEntry

mplsTrafficParamIndex		1.3.6.1.4.1.1991.1.2.15.15.2.1.14.1.1
Uniquely identifies this row of the table. Note that zero represents an invalid index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..2147483647

mplsTrafficParamMaxRate		1.3.6.1.4.1.1991.1.2.15.15.2.1.14.1.2
Maximum rate in kilobits/second.
Status: current	Access: read-create
OBJECT-TYPE
	MplsBitRate

mplsTrafficParamMeanRate		1.3.6.1.4.1.1991.1.2.15.15.2.1.14.1.3
Mean rate in kilobits/second.
Status: current	Access: read-create
OBJECT-TYPE
	MplsBitRate

mplsTrafficParamMaxBurstSize		1.3.6.1.4.1.1991.1.2.15.15.2.1.14.1.4
Maximum burst size in bytes.
Status: current	Access: read-create
OBJECT-TYPE
	MplsBurstSize

mplsTrafficParamRowStatus		1.3.6.1.4.1.1991.1.2.15.15.2.1.14.1.5
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

mplsTrafficParamStorageType		1.3.6.1.4.1.1991.1.2.15.15.2.1.14.1.6
The storage type for this object. If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

mplsXCTrapEnable		1.3.6.1.4.1.1991.1.2.15.15.2.1.15
If this object is set to true(1), then it enables the emission of mplsXCUp and mplsXCDown notifications; otherwise these notifications are not emitted.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

mplsXCUp		1.3.6.1.4.1.1991.1.2.15.15.2.2.0.1
This notification is generated when the mplsXCOperStatus object for one or more contiguous entries in mplsXCTable are about to enter the up(1) state from some other. The included values of mplsXCOperStatus MUST both be set equal to this other state. The two instances of mplsXCOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the up(1) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two mplsXCOperStatus objects MUST be the identical.
Status: current	Access: read-write
NOTIFICATION-TYPE

mplsXCDown		1.3.6.1.4.1.1991.1.2.15.15.2.2.0.2
This notification is generated when the mplsXCOperStatus object for one or more contiguous entries in mplsXCTable are about to enter the down(2) state from some other. The included values of mplsXCOperStatus MUST both be set equal to this other state. The two instances of mplsXCOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the down(2) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two mplsXCOperStatus objects MUST be the identical.
Status: current	Access: read-write
NOTIFICATION-TYPE

mplsLsrGroups		1.3.6.1.4.1.1991.1.2.15.15.2.3.1
OBJECT IDENTIFIER

mplsLsrCompliances		1.3.6.1.4.1.1991.1.2.15.15.2.3.2
OBJECT IDENTIFIER

mplsLsrModuleCompliance		1.3.6.1.4.1.1991.1.2.15.15.2.3.2.1
Compliance statement for agents that support the MPLS LSR MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

mplsInterfaceGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.1
Collection of objects needed for MPLS interface configuration and performance information.
Status: current	Access: read-only
OBJECT-GROUP

mplsInSegmentGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.2
Collection of objects needed to implement an in- segment.
Status: current	Access: read-only
OBJECT-GROUP

mplsOutSegmentGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.3
Collection of objects needed to implement an out- segment.
Status: current	Access: read-only
OBJECT-GROUP

mplsXCGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.4
Collection of objects needed to implement a cross-connect entry.
Status: current	Access: read-only
OBJECT-GROUP

mplsXCOptionalGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.5
Collection of optional objects for implementing a cross-connect entry.
Status: current	Access: read-only
OBJECT-GROUP

mplsPerfGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.6
Collection of objects providing performance information about an LSR.
Status: current	Access: read-only
OBJECT-GROUP

mplsHCInSegmentPerfGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.7
Object(s) providing performance information specific to out-segments for which the object mplsInterfaceInOctets wraps around too quickly.
Status: current	Access: read-only
OBJECT-GROUP

mplsHCOutSegmentPerfGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.8
Object(s) providing performance information specific to out-segments for which the object mplsInterfaceOutOctets wraps around too quickly.
Status: current	Access: read-only
OBJECT-GROUP

mplsTrafficParamGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.9
Object(s) required for supporting QoS resource reservation.
Status: current	Access: read-only
OBJECT-GROUP

mplsXCIsPersistentGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.10
Objects needed to support persistent cross- connects.
Status: current	Access: read-only
OBJECT-GROUP

mplsXCIsNotPersistentGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.11
Objects needed to support non-persistent cross- connects.
Status: current	Access: read-only
OBJECT-GROUP

mplsLabelStackGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.12
Objects needed to support label stacking.
Status: current	Access: read-only
OBJECT-GROUP

mplsSegmentDiscontinuityGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.13
A collection of objects providing information specific to segment discontinuities..
Status: current	Access: read-only
OBJECT-GROUP

mplsLsrNotificationGroup		1.3.6.1.4.1.1991.1.2.15.15.2.3.1.14
Set of notifications implemented in this module. None is mandatory.
Status: current	Access: read-only
NOTIFICATION-GROUP

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor