HP-PROCURVE-420-PRIVATE-MIB

File: HP-PROCURVE-420-PRIVATE-MIB.mib (46474 bytes)

Imported modules

RFC1213-MIB RFC1155-SMI SNMPv2-SMI

Imported symbols

ifIndex mgmt Counter
IpAddress enterprises Integer32
Counter32 OBJECT-TYPE

Defined Types

PhysAddress  
OCTET STRING    

Guage32  
Counter    

MacAddress  
OCTET STRING    

DisplayString  
OCTET STRING    

TruthValue  
INTEGER false(2), true(1)    

LineEntry  
SEQUENCE    
  lineIndex Integer32
  lineDataBits Integer32
  lineParity INTEGER
  lineSpeed Integer32
  lineStopBits Integer32

PortEntry  
SEQUENCE    
  portIndex Integer32
  portName DisplayString
  portType INTEGER
  portSpeedDpxCfg INTEGER
  portFlowCtrlCfg INTEGER
  portCapabilities INTEGER
  portAutonegotiation INTEGER
  portSpeedDpxStatus INTEGER
  portFlowCtrlStatus INTEGER

Hpdot11StationConfigEntry  
SEQUENCE    
  hpdot11portIndex Integer32
  hpdot11DesiredSSID OCTET STRING
  hpdot11BeaconPeriod INTEGER
  hpdot11DTIMPeriod INTEGER
  hpdot11OperationalRateSet INTEGER
  hpdot11AuthenticationAlgorithm INTEGER

Hpdot11PrivacyEntry  
SEQUENCE    
  hpdot11PrivacyportIndex Integer32
  hpdot11PrivacyInvoked INTEGER
  hpdot11WEPDefaultKeyID INTEGER
  hpdot11WEPKeyMappingLength INTEGER

Hpdot11OperationEntry  
SEQUENCE    
  hpdot11OperationIndex Integer32
  hpdot11RTSThreshold INTEGER
  hpdot11FragmentationThreshold INTEGER

Hpdot11PhyOperationEntry  
SEQUENCE    
  hpdot11Index Integer32
  hpdot11CurrentChannel INTEGER
  hpdot11TurboModeEnabled INTEGER
  hpdot11PreambleLength INTEGER

Hpdot11AuthenticationServerEntry  
SEQUENCE    
  hpdot11serverIndex Integer32
  hpdot11AuthenticationServer IpAddress
  hpdot11AuthenticationPort INTEGER
  hpdot11AuthenticationKey DisplayString
  hpdot11AuthenticationRetransmit INTEGER
  hpdot11AuthenticationTimeout INTEGER

Hpdot11FilterEntry  
SEQUENCE    
  hpdot11FilterIndex Integer32
  hpdot11FilterAddress PhysAddress
  hpdot11FilterStatus INTEGER

Hpdot11WEPDefaultKeys11gEntry  
SEQUENCE    
  hpdot11WEPDefaultKey11gLength INTEGER
  hpdot11WEPDefaultKey11gIndex INTEGER
  hpdot11WEPDefaultKey11gValue OCTET STRING

Defined Values

hP 1.3.6.1.4.1.11
OBJECT IDENTIFIER    

wireless 1.3.6.1.4.1.11.2
OBJECT IDENTIFIER    

enterprise 1.3.6.1.4.1.11.2.3
OBJECT IDENTIFIER    

accessPoint 1.3.6.1.4.1.11.2.3.7
OBJECT IDENTIFIER    

proCurve 1.3.6.1.4.1.11.2.3.7.11
OBJECT IDENTIFIER    

hPProCuve420 1.3.6.1.4.1.11.2.3.7.11.37
OBJECT IDENTIFIER    

enterpriseApSys 1.3.6.1.4.1.11.2.3.7.11.37.1
OBJECT IDENTIFIER    

enterpriseApLineMgnt 1.3.6.1.4.1.11.2.3.7.11.37.2
OBJECT IDENTIFIER    

enterpriseApPortMgnt 1.3.6.1.4.1.11.2.3.7.11.37.3
OBJECT IDENTIFIER    

enterpriseApFileTransferMgt 1.3.6.1.4.1.11.2.3.7.11.37.4
OBJECT IDENTIFIER    

enterpriseApResetMgt 1.3.6.1.4.1.11.2.3.7.11.37.5
OBJECT IDENTIFIER    

enterpriseApIpMgt 1.3.6.1.4.1.11.2.3.7.11.37.6
OBJECT IDENTIFIER    

enterpriseAPdot11 1.3.6.1.4.1.11.2.3.7.11.37.7
OBJECT IDENTIFIER    

swHardwareVer 1.3.6.1.4.1.11.2.3.7.11.37.1.1
Hardware version of the main board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

swBootRomVer 1.3.6.1.4.1.11.2.3.7.11.37.1.2
Boot ROM code version of the main board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

swOpCodeVer 1.3.6.1.4.1.11.2.3.7.11.37.1.3
Operation code version of the main board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

swCountryCode 1.3.6.1.4.1.11.2.3.7.11.37.1.4
Country code of the AP. AL-ALBANIA, DZ-ALGERIA, AR-ARGENTINA, AM-ARMENIA, AU-AUSTRALIA, AT-AUSTRIA, AZ-AZERBAIJAN, BH-BAHRAIN, BY-BELARUS, BE-BELGIUM, BZ-BELIZE, BO-BOLVIA, BR-BRAZIL, BN-BRUNEI_DARUSSALAM, BG-BULGARIA, CA-CANADA, CL-CHILE, CN-CHINA, CO-COLOMBIA, CR-COSTA_RICA, HR-CROATIA, CY-CYPRUS, CZ-CZECH_REPUBLIC, DK-DENMARK, DO-DOMINICAN_REPUBLIC, EC-ECUADOR, EG-EGYPT, EE-ESTONIA, FI-FINLAND, FR-FRANCE, GE-GEORGIA, DE-GERMANY, GR-GREECE, GT-GUATEMALA, HK-HONG_KONG, HU-HUNGARY, IS-ICELAND, IN-INDIA, ID-INDONESIA, IR-IRAN, IE-IRELAND, IL-ISRAEL, IT-ITALY, JP-JAPAN, JO-JORDAN, KZ-KAZAKHSTAN, KP-NORTH_KOREA, KR-KOREA_REPUBLIC, KW-KUWAIT, LV-LATVIA, LB-LEBANON, LI-LIECHTENSTEIN, LT-LITHUANIA, LU-LUXEMBOURG, MO-MACAU, MK-MACEDONIA, MY-MALAYSIA, MX-MEXICO, MC-MONACO, MA-MOROCCO, NA-NORTH_AMERICA, NL-NETHERLANDS, NZ-NEW_ZEALAND, NO-NORWAY, OM-OMAN, PK-PAKISTAN, PA-PANAMA, PE-PERU, PH-PHILIPPINES, PL-POLAND, PT-PORTUGAL, PR-PUERTO_RICO, QA-QATAR, RO-ROMANIA, RU-RUSSIA, SA-SAUDI_ARABIA, SG-SINGAPORE, SK-SLOVAK_REPUBLIC, SI-SLOVENIA, ZA-SOUTH_AFRICA, ES-SPAIN, SE-SWEDEN, CH-SWITZERLAND, SY-SYRIA, TW-TAIWAN, TH-THAILAND, TR-TURKEY, UA-UKRAINE, AE-UNITED_ARAB_EMIRATES, GB-UNITED_KINGDOM, US-UNITED_STATES, UY-URUGUAY, VE-VENEZUELA, VN-VIETNAM
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

lineTable 1.3.6.1.4.1.11.2.3.7.11.37.2.1
Table of descriptive and status information about configuration of each RS-232 line in this system
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LineEntry

lineEntry 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1
An entry in the table, containing information about configuration in one RS232 line of the Access Point.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LineEntry  

lineIndex 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.1
This is defined as RS-232 index.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32  

lineDataBits 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.2
This is defined as number of data bits for the RS232 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Integer32  

lineParity 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.3
This is defined as parity of the RS232 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(99), odd(1), even(2)  

lineSpeed 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.4
This is defined as the speed of the RS-232 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Integer32  

lineStopBits 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.5
This is defined as the number of stop bits for the RS-232 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Integer32  

portTable 1.3.6.1.4.1.11.2.3.7.11.37.3.1
Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains information about each trunk (similar to Cisco's EtherChannel).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1
An entry in the table, containing information about configuration in one switch port of the switch.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortEntry  

portIndex 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.1
This is defined as ifIndex in the IF-MIB.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32  

portName 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.2
Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

portType 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.3
Indicates the port type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), hundredBaseTX(2), hundredBaseFX(3), thousandBaseSX(4), thousandBaseLX(5), thousandBaseT(6), thousandBaseGBIC(7), thousandBaseMiniGBIC(8)  

portSpeedDpxCfg 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.4
Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode hundredBaseTX port can be set as halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as halfDuplex100(4) fullDuplex100(5) thousandBaseSX port can be set as halfDuplex1000(6) fullDuplex1000(7) The actual operating speed and duplex of the port is given by portSpeedDpxStatus.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER auto(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7)  

portFlowCtrlCfg 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.5
(1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (3) Flow control mechanism is backPressure. when the port is in fullDuplex mode.This flow control mechanism will not function. (4) Flow control mechanism is IEEE 802.3x flow control. when the port is in halfDuplex mode.This flow control mechanism will not function. hundredBaseTX and thousandBaseSX port can be set as: enabled(1), disabled(2), backPressure(3), dot3xFlowControl(4). hundredBaseFX port can be set as: enabled(1), disabled(2), backPressure(3). The actual flow control mechanism is used given by portFlowCtrlStatus.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), backPressure(3), dot3xFlowControl(4)  

portCapabilities 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.6
Port capabilities.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER portCap10half(99), portCap10full(1), portCap100half(2), portCap100full(3), portCap1000half(4), portCap1000full(5), reserved6(6), reserved7(7), reserved8(8), reserved9(9), reserved10(10), reserved11(11), reserved12(12), reserved13(13), portCapSym(14), portCapFlowCtrl(15)  

portAutonegotiation 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.7
Whether autonegotiation is enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portSpeedDpxStatus 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.8
The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk and the result is inconsistent among its member ports, this value is error(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER error(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7)  

portFlowCtrlStatus 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.9
(2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trunk and the result is inconsistent among its member ports, this value is error(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER error(1), backPressure(2), dot3xFlowControl(3), none(4)  

transferStart 1.3.6.1.4.1.11.2.3.7.11.37.4.1
Set to go(1) to start a transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER go(1), nogo(2)  

transferType 1.3.6.1.4.1.11.2.3.7.11.37.4.2
Type of file to transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ftp(1), tftp(2)  

fileType 1.3.6.1.4.1.11.2.3.7.11.37.4.3
Type of file to transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER opcode(1), config(2)  

srcFile 1.3.6.1.4.1.11.2.3.7.11.37.4.4
The source file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

destFile 1.3.6.1.4.1.11.2.3.7.11.37.4.5
The destination file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

fileServer 1.3.6.1.4.1.11.2.3.7.11.37.4.6
The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been specified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

userName 1.3.6.1.4.1.11.2.3.7.11.37.4.7
The username specified for an FTP Transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

password 1.3.6.1.4.1.11.2.3.7.11.37.4.8
The password specified for an FTP Transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

restartOpCodeFile 1.3.6.1.4.1.11.2.3.7.11.37.5.1
Name of op-code file for start-up.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

restartControl 1.3.6.1.4.1.11.2.3.7.11.37.5.2
Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Setting this object to coldBoot(3) causes the device to reinitialize configuration parameters in non-volatile memory to default values and restart the application software. When the device is running normally, this variable has a value of running(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER running(1), warmBoot(2), coldBoot(3)  

netConfigIPAddress 1.3.6.1.4.1.11.2.3.7.11.37.6.1
The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

netConfigSubnetMask 1.3.6.1.4.1.11.2.3.7.11.37.6.2
The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

netDefaultGateway 1.3.6.1.4.1.11.2.3.7.11.37.6.3
The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipHttpState 1.3.6.1.4.1.11.2.3.7.11.37.6.4
Whether HTTP is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ipHttpPort 1.3.6.1.4.1.11.2.3.7.11.37.6.5
The port number for HTTP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

hpdot11StationConfigTable 1.3.6.1.4.1.11.2.3.7.11.37.7.1
Table of descriptive and status information about configuration of each radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hpdot11StationConfigEntry

hpdot11StationConfigEntry 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1
An entry in the table, containing information about configuration in one radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Hpdot11StationConfigEntry  

hpdot11portIndex 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.1
Radio index of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32  

hpdot11DesiredSSID 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.2
This attribute reflects the Service Set ID used in the DesiredSSID parameter of the most recent MLME_Scan.request. This value may be modified by an external management entity and used by the local SME to make decisions about the Scanning process.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

hpdot11BeaconPeriod 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.3
This attribute shall specify the number of ms that a station shall use for scheduling Beacon transmissions. This value is transmitted in Beacon and Probe Response frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 20..1000  

hpdot11DTIMPeriod 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.4
This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

hpdot11OperationalRateSet 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.5
This attribute shall specify the set of data rates at which the station may transmit data. Each octet contains a value representing a rate. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mbit/s to 63.5 Mbit/s, and shall be supported (as indicated in the supported rates table) for receiving data. This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames, and is used to determine whether a BSS with which the station desires to synchronize is suitable. It is also used when starting a BSS, as specified in 10.3.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..108  

hpdot11AuthenticationAlgorithm 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.6
This attribute shall be a set of all the authentication algorithms supported by the STAs. The following are the default values and the associated algorithm. Value = 1: Open System Value = 2: Shared Key
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER openSystem(1), sharedKey(2)  

hpdot11PrivacyTable 1.3.6.1.4.1.11.2.3.7.11.37.7.2
Table of descriptive and status information about configuration of each radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hpdot11PrivacyEntry

hpdot11PrivacyEntry 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1
An entry in the table, containing information about configuration in one radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Hpdot11PrivacyEntry  

hpdot11PrivacyportIndex 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.1
Radio index of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32  

hpdot11PrivacyInvoked 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.2
When this attribute is true, it shall indicate that the IEEE 802.11 WEP mechanism is used for transmitting frames of type Data. The default value of this attribute shall be false.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hpdot11WEPDefaultKeyID 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.3
This attribute shall indicate the use of the first, second, or third element of the WEPDefaultKeys array when set to values of zero, one, or two(the fourth are reserved for dynamic key). The default value of this attribute shall be 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

hpdot11WEPKeyMappingLength 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.4
The maximum number of tuples that dot11WEPKeyMappings can hold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..2147483647  

hpdot11mac 1.3.6.1.4.1.11.2.3.7.11.37.7.3
OBJECT IDENTIFIER    

hpdot11OperationTable 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1
Table of descriptive and status information about configuration of each radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hpdot11OperationEntry

hpdot11OperationEntry 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1
An entry in the table, containing information about configuration in one radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Hpdot11OperationEntry  

hpdot11OperationIndex 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.1
Radio index of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32  

hpdot11RTSThreshold 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.2
This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2347  

hpdot11FragmentationThreshold 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.3
This attribute shall specify the mandatory maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. An MSDU or MMPDU shall be fragmented when the resulting frame has an individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 256..2346  

hpdot11phy 1.3.6.1.4.1.11.2.3.7.11.37.7.4
OBJECT IDENTIFIER    

hpdot11PhyOperationTable 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1
Table of descriptive and status information about configuration of each radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hpdot11PhyOperationEntry

hpdot11PhyOperationEntry 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1
An entry in the table, containing information about configuration in one radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Hpdot11PhyOperationEntry  

hpdot11Index 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.1
Radio index of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32  

hpdot11CurrentChannel 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.2
The current operating frequency channel of the network
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

hpdot11TurboModeEnabled 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.3
This attribute, when true, shall indicate that the propietory turbo mode option is enabled. The default value of this attribute shall be false.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(99), on(1), off(2)  

hpdot11PreambleLength 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.4
This attribute determines whether or not a short or a long preamble is used to delineate 802.11 frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER short(1), long(2)  

hpdot11AuthenticationEntry 1.3.6.1.4.1.11.2.3.7.11.37.7.5
OBJECT IDENTIFIER    

hpdot118021xSupport 1.3.6.1.4.1.11.2.3.7.11.37.7.5.1
This attribute, when true(1), indicates that the Enterprise Access Point supports the 802.1x authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TruthValue  

hpdot118021xRequired 1.3.6.1.4.1.11.2.3.7.11.37.7.5.2
This attribute, when true(1), indicates that the Enterprise Access Point requires successful 802.1x authentication for any clients accessing the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TruthValue  

hpdot11AuthenticationServerTable 1.3.6.1.4.1.11.2.3.7.11.37.7.6
Table of descriptive and status information about configuration of each authentication server.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hpdot11AuthenticationServerEntry

hpdot11AuthenticationServerEntry 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1
An entry in the table, containing information about configuration in one radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Hpdot11AuthenticationServerEntry  

hpdot11serverIndex 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.1
Radio index of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32  

hpdot11AuthenticationServer 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.2
This values indicates the IP address of the authentication server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

hpdot11AuthenticationPort 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.3
This values indicates the UDP Port used by the primary authentication server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1024..65535  

hpdot11AuthenticationKey 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.4
This values indicates the shared key used by the authentication server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

hpdot11AuthenticationRetransmit 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.5
This values indicates the retransmit timer length used by the authentication server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

hpdot11AuthenticationTimeout 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.6
This values indicates the Timeout value(sec) used by the authentication server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

hpdot11FilterTable 1.3.6.1.4.1.11.2.3.7.11.37.7.7
Table of status information about each configured MAC Address Filtering Entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hpdot11FilterEntry

hpdot11FilterEntry 1.3.6.1.4.1.11.2.3.7.11.37.7.7.1
An entry in the table, containing information about configuration in one radio of the AP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Hpdot11FilterEntry  

hpdot11FilterIndex 1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.1
Filter index.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32  

hpdot11FilterAddress 1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.2
This values indicates the MAC address of the filter entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

hpdot11FilterStatus 1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.3
This values indicates the Status of the filter entry. Ifallowed, the client is allowed access to the network. If disallowed, the no frames will be forwarded to the network from the client.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allowed(30), denied(31)  

hpdot11smt 1.3.6.1.4.1.11.2.3.7.11.37.7.8
OBJECT IDENTIFIER    

hpdot11WEPDefaultKeys11g 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1
OBJECT IDENTIFIER    

hpdot11WEPDefaultKeys11gTable 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1
Conceptual table for WEP default keys. This table shall contain the four WEP default secret key values corresponding to the four possible KeyID values. The WEP default secret keys are logically WRITE-ONLY. Attempts to read the entries in this table shall return unsuccessful status and values of null or zero. The default value of each WEP default key shall be null.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hpdot11WEPDefaultKeys11gEntry

hpdot11WEPDefaultKeys11gEntry 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1
An Entry (conceptual row) in the WEP Default Keys Table. ifIndex - Each 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are indexed by ifIndex.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Hpdot11WEPDefaultKeys11gEntry  

hpdot11WEPDefaultKey11gLength 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.1
A 40(64)-bits [5 octets WEP], 104(128)-bits [13 octets] or 128(152)-bits [16 octets]
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sixtyFour(64), oneHundredTwentyEight(128), oneHundredFiftyTwo(152)  

hpdot11WEPDefaultKey11gIndex 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.2
The auxiliary variable used to identify instances of the columnar objects in the WEP Default Keys Table. The value of this variable is equal to the WEPDefaultKeyID + 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..4  

hpdot11WEPDefaultKey11gValue 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.3
A 40(64)-bits [5 octets WEP] or 104(128)-bits [13 octets] default secret key value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)