HP-LASERJET-COMMON-MIB

File: HP-LASERJET-COMMON-MIB.mib (637090 bytes)

Imported modules

SNMPv2-SMI

Imported symbols

enterprises OBJECT-TYPE

Defined Types

DisplayString  
STRING    

Defined Values

hp 1.3.6.1.4.1.11
OBJECT IDENTIFIER    

nm 1.3.6.1.4.1.11.2
OBJECT IDENTIFIER    

hpsystem 1.3.6.1.4.1.11.2.3
OBJECT IDENTIFIER    

net-peripheral 1.3.6.1.4.1.11.2.3.9
OBJECT IDENTIFIER    

netdm 1.3.6.1.4.1.11.2.3.9.4
OBJECT IDENTIFIER    

dm 1.3.6.1.4.1.11.2.3.9.4.2
OBJECT IDENTIFIER    

device 1.3.6.1.4.1.11.2.3.9.4.2.1
OBJECT IDENTIFIER    

channel 1.3.6.1.4.1.11.2.3.9.4.2.1.6
OBJECT IDENTIFIER    

channelTable 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3
OBJECT IDENTIFIER    

channelEntry 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1
OBJECT IDENTIFIER    

system 1.3.6.1.4.1.11.2.3.9.4.2.1.1
OBJECT IDENTIFIER    

settings-system 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1
OBJECT IDENTIFIER    

status-system 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2
OBJECT IDENTIFIER    

display 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20
OBJECT IDENTIFIER    

display-status 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1
OBJECT IDENTIFIER    

status-message 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.2
OBJECT IDENTIFIER    

status-message1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.2.1
OBJECT IDENTIFIER    

background-message 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37
OBJECT IDENTIFIER    

background-message1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.1
OBJECT IDENTIFIER    

background-message2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.2
OBJECT IDENTIFIER    

id 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3
OBJECT IDENTIFIER    

interface 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4
OBJECT IDENTIFIER    

at 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.2
OBJECT IDENTIFIER    

at1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.2.1
OBJECT IDENTIFIER    

simm 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1
OBJECT IDENTIFIER    

simm1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1
OBJECT IDENTIFIER    

simm2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2
OBJECT IDENTIFIER    

simm3 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3
OBJECT IDENTIFIER    

simm4 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4
OBJECT IDENTIFIER    

simm5 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.5
OBJECT IDENTIFIER    

simm6 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.6
OBJECT IDENTIFIER    

simm7 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.7
OBJECT IDENTIFIER    

simm8 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.8
OBJECT IDENTIFIER    

test 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5
OBJECT IDENTIFIER    

job 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6
OBJECT IDENTIFIER    

settings-job 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1
OBJECT IDENTIFIER    

errorlog 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11
OBJECT IDENTIFIER    

error1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1
OBJECT IDENTIFIER    

error2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2
OBJECT IDENTIFIER    

error3 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3
OBJECT IDENTIFIER    

error4 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4
OBJECT IDENTIFIER    

error5 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5
OBJECT IDENTIFIER    

error6 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6
OBJECT IDENTIFIER    

error7 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7
OBJECT IDENTIFIER    

error8 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8
OBJECT IDENTIFIER    

error9 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9
OBJECT IDENTIFIER    

error10 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10
OBJECT IDENTIFIER    

error11 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11
OBJECT IDENTIFIER    

error12 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12
OBJECT IDENTIFIER    

error13 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13
OBJECT IDENTIFIER    

error14 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14
OBJECT IDENTIFIER    

error15 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15
OBJECT IDENTIFIER    

error16 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16
OBJECT IDENTIFIER    

error17 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17
OBJECT IDENTIFIER    

error18 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18
OBJECT IDENTIFIER    

error19 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19
OBJECT IDENTIFIER    

error20 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20
OBJECT IDENTIFIER    

error21 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21
OBJECT IDENTIFIER    

error22 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22
OBJECT IDENTIFIER    

error23 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23
OBJECT IDENTIFIER    

error24 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24
OBJECT IDENTIFIER    

error25 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25
OBJECT IDENTIFIER    

error26 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26
OBJECT IDENTIFIER    

error27 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27
OBJECT IDENTIFIER    

error28 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28
OBJECT IDENTIFIER    

error29 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29
OBJECT IDENTIFIER    

error30 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30
OBJECT IDENTIFIER    

error31 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31
OBJECT IDENTIFIER    

error32 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32
OBJECT IDENTIFIER    

error33 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33
OBJECT IDENTIFIER    

error34 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34
OBJECT IDENTIFIER    

error35 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35
OBJECT IDENTIFIER    

error36 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36
OBJECT IDENTIFIER    

error37 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37
OBJECT IDENTIFIER    

error38 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38
OBJECT IDENTIFIER    

error39 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39
OBJECT IDENTIFIER    

error40 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40
OBJECT IDENTIFIER    

error41 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41
OBJECT IDENTIFIER    

error42 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42
OBJECT IDENTIFIER    

error43 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43
OBJECT IDENTIFIER    

error44 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44
OBJECT IDENTIFIER    

error45 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45
OBJECT IDENTIFIER    

error46 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46
OBJECT IDENTIFIER    

error47 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47
OBJECT IDENTIFIER    

error48 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48
OBJECT IDENTIFIER    

error49 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49
OBJECT IDENTIFIER    

error50 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50
OBJECT IDENTIFIER    

source-subsystem 1.3.6.1.4.1.11.2.3.9.4.2.1.2
OBJECT IDENTIFIER    

io 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1
OBJECT IDENTIFIER    

settings-io 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1
OBJECT IDENTIFIER    

status-io 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.2
OBJECT IDENTIFIER    

ports 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3
OBJECT IDENTIFIER    

port1 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1
OBJECT IDENTIFIER    

parallel 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.1
OBJECT IDENTIFIER    

processing-subsystem 1.3.6.1.4.1.11.2.3.9.4.2.1.3
OBJECT IDENTIFIER    

pdl 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3
OBJECT IDENTIFIER    

pdl-esc-p 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.5
OBJECT IDENTIFIER    

settings-pdl 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1
OBJECT IDENTIFIER    

pdl-pcl 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3
OBJECT IDENTIFIER    

pdl-postscript 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4
OBJECT IDENTIFIER    

pjl 1.3.6.1.4.1.11.2.3.9.4.2.1.3.5
OBJECT IDENTIFIER    

destination-subsystem 1.3.6.1.4.1.11.2.3.9.4.2.1.4
OBJECT IDENTIFIER    


settings-prt-eng 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1
OBJECT IDENTIFIER    

status-prt-eng 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2
OBJECT IDENTIFIER    

intray 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3
OBJECT IDENTIFIER    

settings-intray 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1
OBJECT IDENTIFIER    

status-intray 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.2
OBJECT IDENTIFIER    

marking-agent 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5
OBJECT IDENTIFIER    

settings-marking-agent 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1
OBJECT IDENTIFIER    

imaging 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6
OBJECT IDENTIFIER    

hrm 1.3.6.1.4.1.11.2.3.9.4.2.3
OBJECT IDENTIFIER    

hrStorage 1.3.6.1.4.1.11.2.3.9.4.2.3.2
OBJECT IDENTIFIER    

hrStorageTable 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3
OBJECT IDENTIFIER    

hrStorageEntry 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1
OBJECT IDENTIFIER    

hrDevice 1.3.6.1.4.1.11.2.3.9.4.2.3.3
OBJECT IDENTIFIER    

hrDeviceTable 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2
OBJECT IDENTIFIER    

hrDeviceEntry 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1
OBJECT IDENTIFIER    

hrPrinterTable 1.3.6.1.4.1.11.2.3.9.4.2.3.3.5
OBJECT IDENTIFIER    

hrPrinterEntry 1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1
OBJECT IDENTIFIER    

printmib 1.3.6.1.4.1.11.2.3.9.4.2.2
OBJECT IDENTIFIER    

prtGeneral 1.3.6.1.4.1.11.2.3.9.4.2.2.5
OBJECT IDENTIFIER    

prtGeneralTable 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1
OBJECT IDENTIFIER    

prtGeneralEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1
OBJECT IDENTIFIER    

prtLocalization 1.3.6.1.4.1.11.2.3.9.4.2.2.7
OBJECT IDENTIFIER    

prtLocalizationTable 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1
OBJECT IDENTIFIER    

prtLocalizationEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1
OBJECT IDENTIFIER    

prtStorageRefTable 1.3.6.1.4.1.11.2.3.9.4.2.2.5.2
OBJECT IDENTIFIER    

prtStorageRefEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.5.2.1
OBJECT IDENTIFIER    

prtDeviceRefTable 1.3.6.1.4.1.11.2.3.9.4.2.2.5.3
OBJECT IDENTIFIER    

prtDeviceRefEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.5.3.1
OBJECT IDENTIFIER    

prtMarker 1.3.6.1.4.1.11.2.3.9.4.2.2.10
OBJECT IDENTIFIER    

prtMarkerTable 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2
OBJECT IDENTIFIER    

prtMarkerEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1
OBJECT IDENTIFIER    

prtMarkerColorant 1.3.6.1.4.1.11.2.3.9.4.2.2.12
OBJECT IDENTIFIER    

prtMarkerColorantTable 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1
OBJECT IDENTIFIER    

prtMarkerColorantEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1
OBJECT IDENTIFIER    

prtConsoleDisplayBuffer 1.3.6.1.4.1.11.2.3.9.4.2.2.16
OBJECT IDENTIFIER    

prtConsoleDisplayBufferTable 1.3.6.1.4.1.11.2.3.9.4.2.2.16.5
OBJECT IDENTIFIER    

prtConsoleDisplayBufferEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.16.5.1
OBJECT IDENTIFIER    

prtConsoleLights 1.3.6.1.4.1.11.2.3.9.4.2.2.17
OBJECT IDENTIFIER    

prtConsoleLightTable 1.3.6.1.4.1.11.2.3.9.4.2.2.17.6
OBJECT IDENTIFIER    

prtConsoleLightEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1
OBJECT IDENTIFIER    

prtAlert 1.3.6.1.4.1.11.2.3.9.4.2.2.18
OBJECT IDENTIFIER    

prtAlertTable 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1
OBJECT IDENTIFIER    

prtAlertEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1
OBJECT IDENTIFIER    

phd 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5
OBJECT IDENTIFIER    

phd2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2
OBJECT IDENTIFIER    

phd3 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3
OBJECT IDENTIFIER    

phd4 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4
OBJECT IDENTIFIER    

phd5 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5
OBJECT IDENTIFIER    

phd6 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6
OBJECT IDENTIFIER    

intrays 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3
OBJECT IDENTIFIER    

intray1 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1
OBJECT IDENTIFIER    

outbin 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4
OBJECT IDENTIFIER    

settings-outbin 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.1
OBJECT IDENTIFIER    

outbins 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3
OBJECT IDENTIFIER    

outbin1 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1
OBJECT IDENTIFIER    

outbin2 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.2
OBJECT IDENTIFIER    

outbin3 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.3
OBJECT IDENTIFIER    

outbin4 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.4
OBJECT IDENTIFIER    

outbin5 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.5
OBJECT IDENTIFIER    

outbin6 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.6
OBJECT IDENTIFIER    

outbin7 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.7
OBJECT IDENTIFIER    

outbin8 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.8
OBJECT IDENTIFIER    

outbin9 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.9
OBJECT IDENTIFIER    

outbin10 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.10
OBJECT IDENTIFIER    

outbin11 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.11
OBJECT IDENTIFIER    

ph 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7
OBJECT IDENTIFIER    

ph-devices 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3
OBJECT IDENTIFIER    

ph2 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.2
OBJECT IDENTIFIER    

ph3 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.3
OBJECT IDENTIFIER    

ph4 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.4
OBJECT IDENTIFIER    

ph5 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.5
OBJECT IDENTIFIER    

ph6 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.6
OBJECT IDENTIFIER    


settings-print-media 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1
OBJECT IDENTIFIER    

media-info 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3
OBJECT IDENTIFIER    

media1 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1
OBJECT IDENTIFIER    

media2 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2
OBJECT IDENTIFIER    

media3 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3
OBJECT IDENTIFIER    

media4 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4
OBJECT IDENTIFIER    

media5 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5
OBJECT IDENTIFIER    

media6 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6
OBJECT IDENTIFIER    

media7 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7
OBJECT IDENTIFIER    

media8 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8
OBJECT IDENTIFIER    

media9 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9
OBJECT IDENTIFIER    

media10 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10
OBJECT IDENTIFIER    

media11 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11
OBJECT IDENTIFIER    

media12 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12
OBJECT IDENTIFIER    

media13 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13
OBJECT IDENTIFIER    

media14 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14
OBJECT IDENTIFIER    

media15 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15
OBJECT IDENTIFIER    

media16 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16
OBJECT IDENTIFIER    

media17 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17
OBJECT IDENTIFIER    

prtCover 1.3.6.1.4.1.11.2.3.9.4.2.2.6
OBJECT IDENTIFIER    

prtCoverTable 1.3.6.1.4.1.11.2.3.9.4.2.2.6.1
OBJECT IDENTIFIER    

prtCoverEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1
OBJECT IDENTIFIER    

prtMarkerSupplies 1.3.6.1.4.1.11.2.3.9.4.2.2.11
OBJECT IDENTIFIER    

prtMarkerSuppliesTable 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1
OBJECT IDENTIFIER    

prtMarkerSuppliesEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1
OBJECT IDENTIFIER    

prtMediaPath 1.3.6.1.4.1.11.2.3.9.4.2.2.13
OBJECT IDENTIFIER    

prtMediaPathTable 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4
OBJECT IDENTIFIER    

prtMediaPathEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1
OBJECT IDENTIFIER    

file-system 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10
OBJECT IDENTIFIER    

settings-file-system 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1
OBJECT IDENTIFIER    

status-file-system 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2
OBJECT IDENTIFIER    

file-systems 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3
OBJECT IDENTIFIER    

file-system1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.1
OBJECT IDENTIFIER    

file-system2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.2
OBJECT IDENTIFIER    

file-system3 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.3
OBJECT IDENTIFIER    

file-system4 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.4
OBJECT IDENTIFIER    

resource-manager 1.3.6.1.4.1.11.2.3.9.4.2.1.1.12
OBJECT IDENTIFIER    

mass-storage-resources 1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3
OBJECT IDENTIFIER    

hrDiskStorageTable 1.3.6.1.4.1.11.2.3.9.4.2.3.3.6
OBJECT IDENTIFIER    

hrDiskStorageEntry 1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1
OBJECT IDENTIFIER    

hrPartitionTable 1.3.6.1.4.1.11.2.3.9.4.2.3.3.7
OBJECT IDENTIFIER    

hrPartitionEntry 1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1
OBJECT IDENTIFIER    

hrFSTable 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8
OBJECT IDENTIFIER    

hrFSEntry 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1
OBJECT IDENTIFIER    

mio 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3
OBJECT IDENTIFIER    

mio1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1
OBJECT IDENTIFIER    

mio2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2
OBJECT IDENTIFIER    

mio3 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.3
OBJECT IDENTIFIER    

active-print-jobs 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2
OBJECT IDENTIFIER    

job-being-parsed 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1
OBJECT IDENTIFIER    

job-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5
OBJECT IDENTIFIER    

job-info-attribute 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23
OBJECT IDENTIFIER    

status-pdl 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.2
OBJECT IDENTIFIER    

jetsend-proc-sub 1.3.6.1.4.1.11.2.3.9.4.2.1.3.8
OBJECT IDENTIFIER    

settings-jetsend 1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.1
OBJECT IDENTIFIER    

jetsend-contact 1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.3
OBJECT IDENTIFIER    

settings-jetsend-contact 1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.3.1
OBJECT IDENTIFIER    

held-job 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7
OBJECT IDENTIFIER    

held-job-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1
OBJECT IDENTIFIER    

held-job-control 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2
OBJECT IDENTIFIER    

accounting 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16
OBJECT IDENTIFIER    

printer-accounting 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1
OBJECT IDENTIFIER    

scanner-accounting 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2
OBJECT IDENTIFIER    

scanned-media-usage 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1
OBJECT IDENTIFIER    

scanner 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2
OBJECT IDENTIFIER    

settings-scanner 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1
OBJECT IDENTIFIER    

remote-procedure-call 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13
OBJECT IDENTIFIER    

settings-rpc 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.1
OBJECT IDENTIFIER    

status-rpc 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2
OBJECT IDENTIFIER    

rpc-services 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3
OBJECT IDENTIFIER    

mount 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.1
OBJECT IDENTIFIER    

settings-mount 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.1.1
OBJECT IDENTIFIER    

nfs-server 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2
OBJECT IDENTIFIER    

settings-nfs-server 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.1
OBJECT IDENTIFIER    

status-nfs-server 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.2
OBJECT IDENTIFIER    

rpc-bind 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3
OBJECT IDENTIFIER    

settings-rpc-bind 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3.1
OBJECT IDENTIFIER    

status-rpc-bind 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3.2
OBJECT IDENTIFIER    

xport-interface 1.3.6.1.4.1.11.2.3.9.4.2.1.1.14
OBJECT IDENTIFIER    

status-xip 1.3.6.1.4.1.11.2.3.9.4.2.1.1.14.2
OBJECT IDENTIFIER    

prtInterpreter 1.3.6.1.4.1.11.2.3.9.4.2.2.15
OBJECT IDENTIFIER    

prtInterpreterTable 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1
OBJECT IDENTIFIER    

prtInterpreterEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1
OBJECT IDENTIFIER    

simm1-bank 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6
OBJECT IDENTIFIER    

simm1-bank1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1
OBJECT IDENTIFIER    

simm1-bank2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2
OBJECT IDENTIFIER    

simm2-bank 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6
OBJECT IDENTIFIER    

simm2-bank1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1
OBJECT IDENTIFIER    

simm2-bank2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2
OBJECT IDENTIFIER    

simm3-bank 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6
OBJECT IDENTIFIER    

simm3-bank1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.1
OBJECT IDENTIFIER    

simm3-bank2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.2
OBJECT IDENTIFIER    

mass-storage-block-driver 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15
OBJECT IDENTIFIER    

settings-mass-storage-bd 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1
OBJECT IDENTIFIER    

status-mass-storage-bd 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.2
OBJECT IDENTIFIER    

mass-storage-block-drivers 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.3
OBJECT IDENTIFIER    

mass-storage-bd2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.3.2
OBJECT IDENTIFIER    

settings-msbd2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.3.2.1
OBJECT IDENTIFIER    

spooler 1.3.6.1.4.1.11.2.3.9.4.2.1.2.4
OBJECT IDENTIFIER    

settings-spooler 1.3.6.1.4.1.11.2.3.9.4.2.1.2.4.1
OBJECT IDENTIFIER    

media-modes 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4
OBJECT IDENTIFIER    

media-mode-details 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.6
OBJECT IDENTIFIER    

media-mode1 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.6.1
OBJECT IDENTIFIER    

media-mode2 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.6.2
OBJECT IDENTIFIER    

media-mode3 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.6.3
OBJECT IDENTIFIER    

media-mode4 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.6.4
OBJECT IDENTIFIER    

media-mode5 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.6.5
OBJECT IDENTIFIER    

phd1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.1
OBJECT IDENTIFIER    

intray2 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2
OBJECT IDENTIFIER    

intray3 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3
OBJECT IDENTIFIER    

intray4 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.4
OBJECT IDENTIFIER    

intray5 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.5
OBJECT IDENTIFIER    

intray6 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.6
OBJECT IDENTIFIER    

intray7 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.7
OBJECT IDENTIFIER    

outbin3 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.3
OBJECT IDENTIFIER    

media-size 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5
OBJECT IDENTIFIER    

prtInput 1.3.6.1.4.1.11.2.3.9.4.2.2.8
OBJECT IDENTIFIER    

prtInputTable 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2
OBJECT IDENTIFIER    

prtInputEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1
OBJECT IDENTIFIER    

prtOutput 1.3.6.1.4.1.11.2.3.9.4.2.2.9
OBJECT IDENTIFIER    

prtOutputTable 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2
OBJECT IDENTIFIER    

prtOutputEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1
OBJECT IDENTIFIER    

tables 1.3.6.1.4.1.11.2.3.9.4.2.1.7
OBJECT IDENTIFIER    

channel-table 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2
OBJECT IDENTIFIER    

channel-entry 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1
OBJECT IDENTIFIER    

prtChannel 1.3.6.1.4.1.11.2.3.9.4.2.2.14
OBJECT IDENTIFIER    

prtChannelTable 1.3.6.1.4.1.11.2.3.9.4.2.2.14.1
OBJECT IDENTIFIER    

prtChannelEntry 1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1
OBJECT IDENTIFIER    

printed-media-usage 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1
OBJECT IDENTIFIER    

localization-language 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.1
Localization language used by the device for device generated PML strings, control panel messages, and text contained in any of the printer generated printed pages. The order is the same order that is defined in MIO. Since the MIO values start at zero, one has been added to each value.
OBJECT-TYPE    
  INTEGER eEnglish(1), eFrench(2), eGerman(3), eSpanish(4), eItalian(5), eSwedish(6), eDanish(7), eNorwegian(8), eDutch(9), eFinnish(10), eJapanese(11), ePortuguese(12), ePolish(13), eTurkish(14)  

not-ready-printer 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.2
Indicates if any of the sub-systems in the printer are not ready. A sub-system is not ready if the sub-system is unable to perform its function until some sort of intervention occurs. If there are no items in the NOT- READY-PRINTER collection (i.e. no bits are set), then all printer sub- systems are ready. Each sub-system has a sub-system specific not ready object. If a sub-system specific not ready object contains any items, then the associated item will be in the NOT-READY collection.
OBJECT-TYPE    
  STRING  

not-ready-controller 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.3
Indicates if the hardware controller sub-system in the device is not ready. If there are no items in the collection (i.e. no bits are set), then the hardware controller sub-system is ready. If there is an item present, then the item indicates what is causing the hardware controller sub-system to be not ready. If the cControllerFailure item is in the collection, then a hardware error was detected on the main controller PC board, sometimes called the formatter or the logic broad. Example controller hardware errors include DRAM controller failure, clock failure, memory parity error, and ROM CRC error. The cFirmwareFailure item is in the collection if a firmware/software error was detected. Device specific detailed error information can be retrieved from the error log objects, if the device supports those objects. The POS will list which device failures cause each item to be included in the collection. Additional information: A controller failure occurrence will set the cControllerFailure bit (bit 1). The controller failures are: 62.X Service, 63 Service, 65 Service, 67 Service, 68 Service, and 68 Error. A SIMM failure occurrence will set the cSIMMFailure bit (bit 2). The SIMM failures are 61.X Service, 53-XY-ZZ Error, and 72 Service. A DISK failure occurrence will set the cATFailure bit (bit 3). The DISK failure is FS DISK FAILURE.
OBJECT-TYPE    
  STRING  

not-idle 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.4
Indicates if any of the sub-systems in the device are not idle. The I/O source sub-system is considered not idle if there is unprocessed PDL data in the device. The PDL processing sub-system is considered not idle if the device is processing a print job. The print engine destination sub-system is considered not idle if media is moving (i.e. the device is printing). [other text here describing what causes the other sub-systems to be considered not idle].
OBJECT-TYPE    
  STRING  

on-off-line 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.5
To bring the PDL processing sub-system on or off line. If the device is a printer, then the printer does not process print job data when the printer is off line. PML communication persists. Additional information: When the printer is in the Offline state, printing will stop as soon as possible (no more sheets of media are pulled from input trays). The I/O is taken offline also. Setting to eOnline has the following affect: Printer will immediately go to or remain in the Online state; status is returned. If the printer's current state is Offline with a pending error condition that prevents the printer from going to the Online state, the printer will remain in the Offline state; status is returned Setting to eOffline has the following affect: Printer will immediately go to or remain in the Offline state; status is returned. If pages are being printed, those pages will complete with the printer in the Offline state. Setting to eOfflineAtEndOfJob has the following affect: If not in a job or already in the Offline state, the printer will immediately go to or remain in the Offline state; status is returned. If in a job and the current state is Online, the printer will remain in the Online state, with the value of this object as eOfflineAtEndOfJob, until the end of the job; status is returned. At the end of the job, the printer goes to the Offline state and the value of this object becomes eOffline. Setting this object to eOffline or eOnline before the end of the job causes the action for that value to be taken immediately.
OBJECT-TYPE    
  INTEGER eOnline(1), eOffline(2), eOfflineAtEndOfJob(3)  

continue 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.6
A device can support a class of errors called continuable errors. When a continuable error is encountered, the device requires a continue event to occur before the device will continue operation. One continue event is setting the CONTINUE object to eInitiateAction. Devices can support other continue events, like auto-continue. A continue event causes the continuable error to be acknowledged, thus allowing the device to continue. Each device needs to list the continuable errors. If the device doesn't currently have an unacknowledged continuable error, the response will contain . Additional information: See the CLEARABLE-WARNING and AUTO-CONTINUE objects for the errors that this object will clear.
OBJECT-TYPE    
  INTEGER eInitiateAction(1)  

user-nvram-reset 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.12
Setting to eTrue causes all user NVRAM settings to factory default settings. May also perform POWER-ON- RESET functionality thus loosing print job data. The POS will list which objects are effected by a user NVRAM reset. Some items are NVRAM settings, but not user controllable, so this action may not cause all of NVRAM to be reset. Some examples of NVRAM settings that may not be affected are page count, internally used pen information, line configuration information, etc. Additional information: Setting to eTrue returns the NVRAM items listed below to their factory default values. Performs the same function as the 'MENU RESET' function supported by the control panel except when printer is in Offline state, setting this OID to eTrue will not take the printer to the Online state. DEFAULT-COPIES DEFAULT-MEDIA-SIZE DEFAULT-ORIENTATION DEFAULT-LINES-PER-PAGE DEFAULT-MANUAL-FEED DEFAULT-RET DEFAULT-PRINT-QUALITY PCL-DEFAULT-FONT-SOURCE PCL-DEFAULT-FONT-NUMBER PCL-DEFAULT-FONT-HEIGHT PCL-DEFAULT-FONT-WIDTH PCL-DEFAULT-SYMBOL-SET DEFAULT-VERTICAL-BLACK-RESOLUTION DEFAULT-HORIZONTAL-BLACK-RESOLUTION DEFAULT-PDL CONTEXT-SENSITIVE-PDL-SELECTION ENERGY-STAR IO-TIMEOUT DEFAULT-PAGE-PROTECT POSTSCRIPT-JAM-RECOVERY (PostScript installed) POSTSCRIPT-PRINT-ERRORS (PostScript installed)
OBJECT-TYPE    
  INTEGER eTrue(1)  

total-ram-size 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.21
Identifies total amount of RAM, in bytes, available to the controller for general computing.
OBJECT-TYPE    
  INTEGER  

status-printer 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.22
Indicates if any of the sub-systems in the device in a warning condition. A warning condition exists if the sub-system is useable, but not at its highest state of functionality.
OBJECT-TYPE    
  STRING  

status-controller 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.23
Indicates if the hardware controller sub-system in a warning condition.
OBJECT-TYPE    
  STRING  

auto-continue 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.7
Indicates if the device will automatically continue after encountering a continuable error. If AUTO- CONTINUE is set to eOn, the device will automatically generate continue event to acknowledge continuable errors. If AUTO-CONTINUE is set to eOff, then some other continue event will have to acknowledge the continuable error. Additional information: If this is set to eOn the device displays an error message and goes offline for ten seconds. After ten seconds the printer automatically returns to the online state. If this is set to eOff then the device displays an error message and goes offline. It remains offline until the operator presses the GO key or until the CONTINUE object is set. If the printer is not idle, the new value may not take effect until a job boundary is reached. If a get is done on this object before the job boundary is reached, the value last set will be returned.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2)  

display-column-size 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1.1
Indicates the number of characters displayable on each row of the printer's display.
OBJECT-TYPE    
  INTEGER  

display-number-of-rows 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1.2
Indicates the number of rows displayable on the printer's display.
OBJECT-TYPE    
  INTEGER  

status-msg-line1-part1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.2.1.1
First part of the first line of the printer's status message. Additional information: In the Offline state, device only returns 00 OFFLINE and not the actual content of control panel display.
OBJECT-TYPE    
  DisplayString  

background-status-msg-line1-part1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.1.1
The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '00 READY'. Additional information: The display size for the LaserJet 4050 Series printers is 2 X 16. The value of this object and the current value of BACKGROUND-STATUS-MSG-LINE2-PART1 are displayed together on the 2-line display, but they must be set independently. If line 2 has been set, and the next message to be displayed only requires line 1, BACKGROUND-STATUS-MSG-LINE2-PART1 must be set to the null string to clear it. This object allows a message to be displayed when it is the highest priority message. Setting this object does not guarantee the message will be displayed; and reading it returns the value last written, not the currently displayed message (use prtConsoleDisplayBufferText to read the display). The priority assigned for displaying this message is one lower than the READY message. In other words, the only message that can be replaced by these objects is the READY message. To clear the message, write a null string to both this object and BACKGROUND-STATUS-MSG-LINE2-PART1.
OBJECT-TYPE    
  DisplayString Size(0..16)  

background-status-msg-line2-part1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.2.1
The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '00 READY'. Additional information: See BACKGROUND-STATUS-MSG-LINE1-PART1
OBJECT-TYPE    
  DisplayString Size(0..16)  

error-log-clear 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.38
Setting this object clears all the entries in the error log sub-tree. Additional information: Setting this object removes all errors that have been stored in the printer's non-volatile memory.
OBJECT-TYPE    
  INTEGER eClearErrorLog(1)  

localization-languages-supported 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.52
The list of languages supported by the device. The languages are primarily, but not limited to, two character codes from ISO 639, each separated by a comma character. Additional information: This string will always be in the Roman-8 character set. See prtLocalizationLanguage for details about each language value.
OBJECT-TYPE    
  DisplayString  

localization-countries-supported 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.53
The list of countries supported by the device. The countries are primarily, but not limited to, two character codes from ISO 3166, each separated by a comma character. Additional information: This string will always be in the Roman-8 character set. See prtLocalizationCountry for details about each country value.
OBJECT-TYPE    
  DisplayString  

control-panel-button-press 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.60
Writing this object simulates pressing a button on the control panel.
OBJECT-TYPE    
  INTEGER eGoButton(1), eMenuPlusButton(2), eMenuMinusButton(3), eItemPlusButton(4), eItemMinusButton(5), eValuePlusButton(6), eValueMinusButton(7), eSelectButton(8), eCancelJobButton(9)  

model-number 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.1
Identifies the device model number as listed in the HP corporate price list (e.g. C2121A for DeskJet 500C). The string is as specific as possible. Products should note in POS if the model number on the CPL changes but the device reports the previous model number. If the model number changes based on the installed options, the POS should indicate if only the base model number is returned, or if the device senses the installed options and returns the correct model number. If possible, encode the model number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: The value of this object does not change based on the installed options. The default of this object is the same on all LaserJet 4050 Series printers.
OBJECT-TYPE    
  DisplayString  

serial-number 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.3
Identifies the serial number for the device. If the SERIAL-NUMBER object is set by the user, then setting the object does not need to be protected. If the SERIAL-NUMBER object is set at the factory, then the SERVICE-PASSWORD object must be set correctly before the SERIAL-NUMBER object is writable. If this is a writable object, the POS should indicate the maximum supported string length. If possible, encode the serial number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: This value IS AFFECTED BY NVRAM resets, it is set to the default value of XXXXXXXXXX, when a NVRAM init is done.
OBJECT-TYPE    
  DisplayString Size(0..10)  

fw-rom-datecode 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.5
Identifies the base system firmware date code. The date code will be encoded in the yyyymmdd format. There may be several versions of the base system firmware. The date code associated with the version of the base system firmware that is being used is reported. There may be other date code objects for other specific modules such as fonts, localization modules, etc.; these other datecode objects are device specific.
OBJECT-TYPE    
  DisplayString  

device-location 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.11
User defined device location. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the . Additional information: The maximum supported string length is 16 characters. If the user entered string is too long, the device will store the first 16 characters and will return the status.
OBJECT-TYPE    
  DisplayString  

asset-number 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.12
User defined asset number. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the . Additional information: The maximum supported string length is 8 characters. If the user entered string is too long, the device will store the first 8 characters and will return the status.
OBJECT-TYPE    
  DisplayString  

system-contact 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.13
User defined string containing the name of the person or group that is responsible for the device. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the . Additional information: User defined system contact. The maximum supported string length is 16 characters. If the user entered string is too long, the device will store as much as possible and will return the status.
OBJECT-TYPE    
  DisplayString  

at1-model-number 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.2.1.1
Identifies the AT model number. If the disk was manufactured by HP, then the model number is the one listed in the HP corporate price list. If possible, encode the model number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: The model number is obtained from the disk using the IDE (Intelligent Drive Electronics) Identify command. This objects is only supported if a disk is installed. Returns status if attempting to perform a Get on this OID with no disk installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no disk installed.
OBJECT-TYPE    
  DisplayString  

at1-model-name 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.2.1.2
Returns product information identifying the AT storage device. Example: C3014A Additional information: The product information is obtained from the disk using the IDE (Intelligent Drive Electronics) Identify command. This objects is only supported if a disk is installed. Returns status if attempting to perform a Get on this OID with no disk installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no disk installed.
OBJECT-TYPE    
  DisplayString  

at1-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.2.1.3
Returns information describing the manufacture of this particular AT. May include serial number and firmware revision. Additional information: Returns the model number, serial number, and firmware revision of the installed disk. This information is obtained from the disk using the IDE (Intelligent Drive Electronics) Identify command. Example: HP C3014A JP932412W9 K2A4A059. This objects is only supported if a disk is installed. Returns status if attempting to perform a Get on this OID with no disk installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no disk installed.
OBJECT-TYPE    
  DisplayString  

at1-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.2.1.4
Returns an indication of the type of option installed in this particular AT interface. See SIMM1-TYPE for an explanation of the enumerations. Additional information: eEmpty means the device did not detect any AT. eDiskDrive means the AT contains a disk drive.
OBJECT-TYPE    
  INTEGER eEmpty(1), eDiskDrive(8)  

at1-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.2.1.5
Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: This object contains the size, in bytes, of the installed disk option. This objects is only supported if a disk is installed. Returns status if attempting to perform a Get on this OID with no disk installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no disk installed.
OBJECT-TYPE    
  INTEGER  

simm1-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.4
Returns an indication of the type of option installed in SIMM slot 1. eEmpty means the device did not detect any option installed in the interface slot. eUnknown means the device doesn't recognize the installed option. eUnSupported means the device recognizes the installed option, but does not support the option. eReadOnlyMemory means the installed option contains ROM Ics. eVolatileRandomAccessMemory means the installed option contains RAM ICs that loose data when the power is turned off. eNonVolatileRandomAccessMemory means that the installed option contains RAM ICs that do not loose data when the power is turned off. eFlashMemory means that the installed option contains a type of non-volatile RAM that needs to be erased before it can be written. eDiskDrive means the installed option contains a disk drive. eRamRom means the installed option contains both volatile random access memory and read only memory. eInputPHD means the installed option is an input paper handling device. eOutputPHD means the installed option is an output paper handling device. eIOCard means the installed option is an I/O card. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4050 Series. eRamRom is used to denote LaserJet 4050 Series's combo simm.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eUnSupported(3), eReadOnlyMemory(4), eVolatileRandomAccessMemory(5), eFlashMemory(7), eRamRom(9)  

simm1-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.5
Returns an indication of the capacity of the SIMM installed in SIMM slot 1. The capacity is dependent on the type of option, as indicated by the SIMM1-TYPE object. This object has no meaning if the installed option type is eUnknown or eReadOnlyMemory. This object contains the size, in bytes, if the installed option type is eVolatileRandomAccessMemory, eNonVolatileRandomAccessMemory, eFlashMemory, or eDiskDrive. If the type of the installed option is eRamRom, this object contains the size, in bytes, of the random access memory. If the type of the installed option is eInputPHD, the capacity indicates the number of input trays supported by the installed option. If the type of the installed option is eOutputPHD, the capacity indicates the number of output bins supported by the installed option. If the type of the installed option is eIOCard, the capacity indicates the number of logical I/O ports supported by the I/O card. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM1-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the SIMM is returned.
OBJECT-TYPE    
  INTEGER  

simm2-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.4
Returns an indication of the type of option installed in SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4050 Series. eRamRom is used to denote LaserJet 4050 Series's combo simm.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eUnSupported(3), eReadOnlyMemory(4), eVolatileRandomAccessMemory(5), eFlashMemory(7), eRamRom(9)  

simm2-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.5
Returns an indication of the capacity of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4050 Series. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM2-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the SIMM is returned.
OBJECT-TYPE    
  INTEGER  

simm3-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.4
Returns an indication of the type of option installed in SIMM slot 3. See SIMM1-TYPE for a description.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eUnSupported(3), eReadOnlyMemory(4), eVolatileRandomAccessMemory(5), eFlashMemory(7), eRamRom(9)  

simm3-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.5
Returns an indication of the capacity of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4050 Series. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM3-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the simm is returned.
OBJECT-TYPE    
  INTEGER  

simm4-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.4
Returns an indication of the type of option installed in SIMM slot 4. See SIMM1-TYPE for a description.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eUnSupported(3), eReadOnlyMemory(4), eVolatileRandomAccessMemory(5)  

simm4-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.5
Returns an indication of the capacity of the SIMM installed in SIMM slot 4. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM4-TYPE type is eVolatileRandomAccessMemory.
OBJECT-TYPE    
  INTEGER  

simm5-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.5.4
Returns an indication of the type of option installed in SIMM slot 5. See SIMM1-TYPE for a description.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eUnSupported(3), eReadOnlyMemory(4), eVolatileRandomAccessMemory(5)  

simm5-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.5.5
Returns an indication of the capacity of the SIMM installed in SIMM slot 5. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM5-TYPE type is eVolatileRandomAccessMemory.
OBJECT-TYPE    
  INTEGER  

simm6-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.6.4
Returns an indication of the type of option installed in SIMM slot 6. See SIMM1-TYPE for a description.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eUnSupported(3), eReadOnlyMemory(4), eVolatileRandomAccessMemory(5)  

simm6-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.6.5
Returns an indication of the capacity of the SIMM installed in SIMM slot 6. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM6-TYPE type is eVolatileRandomAccessMemory.
OBJECT-TYPE    
  INTEGER  

simm7-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.7.4
Returns an indication of the type of option installed in SIMM slot 7. See SIMM1-TYPE for a description.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eUnSupported(3), eReadOnlyMemory(4), eVolatileRandomAccessMemory(5)  

simm7-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.7.5
Returns an indication of the capacity of the SIMM installed in SIMM slot 7. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM7-TYPE type is eVolatileRandomAccessMemory.
OBJECT-TYPE    
  INTEGER  

simm8-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.8.4
Returns an indication of the type of option installed in SIMM slot 8. See SIMM1-TYPE for a description.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eUnSupported(3), eReadOnlyMemory(4), eVolatileRandomAccessMemory(5)  

simm8-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.8.5
Returns an indication of the capacity of the SIMM installed in SIMM slot 8. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM8-TYPE type is eVolatileRandomAccessMemory.
OBJECT-TYPE    
  INTEGER  

self-test 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.1
Writing this object allows a device self test to be started. Reading this object provides an indication what self-test is currently executing, if any. Actual self-test operation is device specific. A self test may not be allowed at any arbitrary time. If the device supports the requested self test, but can not start the execution of the self test when requested, the device will respond with . If a non-destructive self test is being started, the device will generate a response before the self test is completed. RECOMMENDATION: If the device is ready (i.e. the NOT- READY-PRINTER object does not contain any items, except maybe being off-line) and is idle (i.e. the NOT-IDLE object does not contain any items), this request should always succeed. This provides a mechanism for driver writers to always determine if the action will succeed or not. Additional information: The eNonDestructiveSelfTest performs limited testing on the printer and its attached paper handling devices. After the self-test is complete a configuration page is printed. The recommended way to cause a configuration page to be printed is to use the PRINT-INTERNAL-PAGE object. Setting this object to eNonDestructiveSelfTest results in a status of and a value of eNonDestructiveSelfTest being returned. If the printer is not idle (whether printing an external job or printing an internal page), this action will be delayed until the next job boundary. See the PRINT-INTERNAL-PAGE object for more details.
OBJECT-TYPE    
  INTEGER eNotInASelfTest(1), eNonDestructiveSelfTest(4)  


clearable-warning 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.1
Returns or controls how the device will track clearable warnings. A clearable warning indicates a transient event in the device. The device will continue after the transient event occurs. If CLEARABLE-WARNING is eOff, the device does not track clearable warnings. If CLEARABLE-WARNING is eOn, all clearable warnings will be tracked until cleared (acknowledged). If CLEARABLE- WARNING is eJob, a clearable warning generated due to an event that occurs because of the print job being processed will be automatically cleared when the device has finished processing the job. Example clearable warning events include the device altering resolution or page protection due to memory constraints. The POS will document what transient events are treated as clearable warnings. Additional information: If set to eOn, the warning is displayed until the GO key is pressed or the CONTINUE object is set. If set to eJob, the warning is displayed until the end of the job in which it was generated.
OBJECT-TYPE    
  INTEGER eOn(2), eJob(3)  

cancel-job 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.2
Cancels the print job whose ID matches the value written to the CANCEL-JOB object. The host first learns the job ID using the CURRENT-JOB-PARSING-ID command. If the printer has completely processed the job, the printer responds with . If the value of the CURRENT-JOB-PARSING-ID is smaller than the value written to the CANCEL-JOB object, then the printer responds with . When read, returns the value of the last job ID what was canceled, or -1 to indicate no job has been canceled. Additional information: If the value written matches the ID of a job that is currently being canceled (for any reason), the printer responds with . LaserJet 4050 Series uses job ID's in the range of 0..32767. Because the ID number can wrap to zero, CURRENT-JOB-PARSING-ID may be smaller than the value written to this object; when this occurs, no error will result as long as the ID is for a currently processing job. This object is write only, so the comment in the general description stating the job ID or -1 will be returned on a read does not apply.
OBJECT-TYPE    
  INTEGER 0..32767  

error1-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.1
Contains some sort of time stamp indicating when error 1 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: This item contains the engine page count when the error occurred. If there is currently no error entry for this object, a '0' will be returned. Note that '0' may also be returned when there is a valid error, but a current page count was unavailable. If ERROR1-CODE object also returns '0', then an error has not yet been logged for this object. See ERROR1-CODE for an explanation of the order used for storing errors.
OBJECT-TYPE    
  INTEGER  

error1-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: Returns a device specific error code. If the error code returned is '0', then the printer has not yet logged an error for this object. When the maximum number of errors is reached (30 on LaserJet 4050 Series printers), and a new error occurs, the error in ERROR1-CODE will be replaced by the one in ERROR2-CODE, and so on until the last error object will be given the value of the new error. The error number is returned in the upper 16 bits. If it is 68, 69, 79, or 80, then the sub code is returned in the lower 16 bits (eg. 68 001C, where the subcode is already a hexadecimal value). If the error number is any other number, then the 1st sub code (XX) will be in bits 15-8 and the 2nd sub code (YY) will be in bits 7-0 (eg. 55.04.02) where XX=04 and YY=02). Example: If the error is 68 001A, then the value returned will be 4456474. To break it down: 4456474 = 0x0044001A The upper 16 bits: 0x0044 = 68 The lower 16 bits: 0x001A = 001A Which is the error: 68 001A Example: If the error is 55.04.241, then the error code will be 3605745. To break it down: 3605745 = 0x003704F1 The upper 16 bits: 0x0037 = 55 The upper byte of the lower 16 bits: 0x04 = 04 The lower byte of the lower 16 bits: 0xF1 = 241 Which is the error: 55.04.241
OBJECT-TYPE    
  INTEGER  

error2-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.1
Contains some sort of time stamp indicating when error 2 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error2-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error3-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.1
Contains some sort of time stamp indicating when error 3 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error3-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error4-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.1
Contains some sort of time stamp indicating when error 4 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error4-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error5-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.1
Contains some sort of time stamp indicating when error 5 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error5-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error6-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.1
Contains some sort of time stamp indicating when error 6 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error6-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error7-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.1
Contains some sort of time stamp indicating when error 7 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error7-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error8-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.1
Contains some sort of time stamp indicating when error 8 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error8-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error9-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.1
Contains some sort of time stamp indicating when error 9 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error9-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error10-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.1
Contains some sort of time stamp indicating when error 10 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error10-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error11-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.1
Contains some sort of time stamp indicating when error 11 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error11-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error12-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.1
Contains some sort of time stamp indicating when error 12 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error12-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error13-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.1
Contains some sort of time stamp indicating when error 13 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error13-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error14-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.1
Contains some sort of time stamp indicating when error 14 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error14-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error15-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.1
Contains some sort of time stamp indicating when error 15 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error15-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error16-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.1
Contains some sort of time stamp indicating when error 16 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error16-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error17-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.1
Contains some sort of time stamp indicating when error 17 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error17-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error18-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.1
Contains some sort of time stamp indicating when error 18 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error18-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error19-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.1
Contains some sort of time stamp indicating when error 19 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error19-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error20-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.1
Contains some sort of time stamp indicating when error 20 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error20-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error21-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.1
Contains some sort of time stamp indicating when error 21 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error21-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error22-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.1
Contains some sort of time stamp indicating when error 22 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error22-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error23-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.1
Contains some sort of time stamp indicating when error 23 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error23-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error24-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.1
Contains some sort of time stamp indicating when error 24 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error24-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error25-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.1
Contains some sort of time stamp indicating when error 25 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error25-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error26-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.1
Contains some sort of time stamp indicating when error 26 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error26-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error27-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.1
Contains some sort of time stamp indicating when error 27 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error27-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error28-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.1
Contains some sort of time stamp indicating when error 28 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error28-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error29-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.1
Contains some sort of time stamp indicating when error 29 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error29-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error30-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.1
Contains some sort of time stamp indicating when error 30 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error30-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error31-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31.1
Contains some sort of time stamp indicating when error 31 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error31-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error32-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32.1
Contains a time stamp indicating when error 32 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error32-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error33-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33.1
Contains a time stamp indicating when error 33 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error33-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error34-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34.1
Contains a time stamp indicating when error 34 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error34-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error35-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35.1
Contains a time stamp indicating when error 35 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error35-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error36-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36.1
Contains a time stamp indicating when error 36 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error36-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error37-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37.1
Contains a time stamp indicating when error 37 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error37-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error38-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38.1
Contains a time stamp indicating when error 38 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error38-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error39-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39.1
Contains a time stamp indicating when error 39 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error39-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error40-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40.1
Contains a time stamp indicating when error 40 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error40-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error41-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41.1
Contains a time stamp indicating when error 41 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error41-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error42-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42.1
Contains a time stamp indicating when error 42 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error42-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error43-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43.1
Contains a time stamp indicating when error 43 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error43-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error44-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44.1
Contains a time stamp indicating when error 44 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error44-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error45-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45.1
Contains a time stamp indicating when error 45 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error45-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error46-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46.1
Contains a time stamp indicating when error 46 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error46-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error47-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47.1
Contains a time stamp indicating when error 47 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error47-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error48-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48.1
Contains a time stamp indicating when error 48 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error48-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error49-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49.1
Contains a time stamp indicating when error 49 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error49-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

error50-time-stamp 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50.1
Contains a time stamp indicating when error 50 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
OBJECT-TYPE    
  INTEGER  

error50-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50.2
Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
OBJECT-TYPE    
  INTEGER  

io-timeout 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.1
The amount of time, in seconds, to wait for more print job data to be received before an I/O timeout occurs. The I/O channel being timed is the I/O channel that received the data associated with the current print job. If an I/O timeout occurs, the PDL processing sub-system assumes all the data associated with the current print job has been received, and processes the end of job in an PDL specific manner. The POS specifies the supported values. Additional information: If an I/O timeout occurs,the PDL processing sub-system will consider it an end of job condition only if there is data from another I/O subsystem waiting to be processed. The supported values are 5 to 300 seconds. Setting to a value outside the supported range returns status and the value will be snapped to the nearest supported value.
OBJECT-TYPE    
  INTEGER 5..300  

io-switch 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.2
Indicates if the device will switch between I/O channels when a job boundary is encountered and print job data is available on another I/O channel.
OBJECT-TYPE    
  INTEGER eYes(1)  

io-buffering 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.5
Returns or controls the manner in which the device performs I/O data buffering. I/O data buffering allows additional print job data to be buffered by the I/O sub- system in an effort to allow the computer sending the data to perform other tasks and to keep the PDL processing sub-system busy. eOff, I/O buffering is disabled. When eOn, I/O buffering is enabled and the IO-BUFFER-SIZE object controls the amount of memory set aside for I/O buffer. When eAuto, I/O buffering is enabled and the I/O buffer size is determined automatically by the device and the IO-BUFFER-SIZE object is not used. Additional information: In a PCL-only printer, all values may be set at any time. When there is less than 4M of memory installed, setting this object to eOn or eAuto will cause to be returned. At exactly 4M of memory, eOn is not a valid setting. At more than 4M of memory any setting is valid, subject to the conditions listed in the interactions below.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2), eAuto(3)  

io-buffer-size 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.6
Returns or configures the amount of memory, in bytes, dedicated to I/O print job data buffering. Attempting to set to an unsupported value causes the device to use the closest supported value. Each device POS should document the list of supported values. Additional information: In LaserJet 4050 Series the minimum supported value is 10K bytes (10240). The maximum supported value is dependent on total memory installed and the amount of memory currently being used by other memory consumers. Use the MAXIMUM-IO-BUFFERING-MEMORY object to determine this value. The following rules determine legal values for this object: 1) Sizes less than 10K bytes will snap to 10K bytes. 2) Sizes between 10K and 100K bytes will be rounded to the nearest 10K. 3) Sizes between 100K bytes and the maximum value allowed will round to the nearest 100K bytes. If the value had to be snapped or rounded, will be returned along with the actual value that was written. Attempting to set this object when IO-BUFFERING is eOff will cause a status of to be returned. When IO-BUFFERING is eOff, reading this object will return a value of zero.
OBJECT-TYPE    
  INTEGER  

maximum-io-buffering-memory 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.7
This object's name is misleading. Returns the maximum amount of additional memory, in bytes, that can be dedicated to buffering print job data.
OBJECT-TYPE    
  INTEGER  

not-ready-source-io 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.2.1
Indicates if the I/O sub-system in the device is not ready. If there are no items in the collection (i.e. no bits are set), then the I/O sub-system is ready. If there is an item present, then the item indicates what is causing the I/O sub-system to be not ready. If the I/O sub-system is not ready due to a soft error, the soft error is considered to be an auto-continuable error, thus it can be acknowledged by setting the CONTINUE object to eTrue.
OBJECT-TYPE    
  STRING  

status-source-io 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.2.2
Indicates if the I/O sub-system in a warning condition.
OBJECT-TYPE    
  STRING  

parallel-speed 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.1.4
Returns or changes the maximum parallel I/O port speed. An eSlow setting causes a 10 us busy pulse per received byte of data. An eFast setting causes a 1.5 us busy pulse per received byte of data. In rare cases, setting this value to eFast can cause the parallel port to no longer transfer data reliably.
OBJECT-TYPE    
  INTEGER eSlow(1), eFast(2)  

parallel-bidirectionality 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.1.5
Returns or changes whether the parallel I/O port supports bidirectional communication.
OBJECT-TYPE    
  INTEGER eUnidirectional(1), eBidirectional(2)  

port1-parallel-speed 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.4
Returns or changes the maximum parallel I/O port speed, for port 1. This object is only supported if this port is a parallel port. An eSlow setting causes a 10 us busy pulse per received byte of data. An eFast setting causes a 1.5 us busy pulse per received byte of data. In rare cases, setting this value to eFast can cause the parallel port to no longer transfer data reliably.
OBJECT-TYPE    
  INTEGER eSlow(1), eFast(2)  

port1-parallel-bidirectionality 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.5
Returns or changes whether the parallel I/O port supports bidirectional communication for port 1. This object is only supported if this port is a parallel port. Additional information: A get on this object returns the current mode for the parallel port. Setting this object specifies whether or not bidirectional communications will be allowed.
OBJECT-TYPE    
  INTEGER eUnidirectional(1), eBidirectional(2)  

default-orientation 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.2
Returns or changes the default orientation. The list of supported values should be documented in the device POS.
OBJECT-TYPE    
  INTEGER ePortrait(1), eLandscape(2)  

default-copies 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.4
Returns or changes default copies. Default copies is the default values used by the PDL to control the number of copies of each page in the print job that are printed. The print job can override this value. The list of supported values should be documented in the device POS. Additional information: The supported values are 1 through 999. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snaps are as follows: <1 snaps to 1 >999 snaps to 999
OBJECT-TYPE    
  INTEGER 1..999  

form-feed 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.5
Instructs the PDL processing sub-system to finishing processing the current page of the current job. Form feed is also known as close page or eject page. If the PDL processing sub-system is in a FORM-FEED-NEEDED state, this causes the device to flush or finish processing the current page of the current job. If the device is not in the FORM-FEED-NEEDED state, an will occur.
OBJECT-TYPE    
  INTEGER eInitiateAction(1)  

resource-saving 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.6
Returns or changes PDL resource saving. Resource saving stores a PDL's permanent soft resources, like fonts, even when another PDL is active. Resource saving is also called environment saving. When eOff, resource saving is disabled. When ON, resource saving is enabled and memory is set aside for each PDL based on that PDL's resource saving memory size object, to store that PDL's permanent soft resources. When eAuto, resource saving is enabled and memory space for each installed PDL is determined automatically. The device POS should document what values are legal when only one PDL is installed. Additional information: When PCL (including PCL/XL) is the only PDL installed in LaserJet 4050 Series, eOn is not a legal value. Attempting to set this object to eOn with a PCL-only printer will result in a status of being returned. When Postscript is installed and less than 8 Megabytes of RAM are present, resource saving is not available. The only valid value for this object is eOff. Attempting to set this object to eOn or eAuto will cause to be returned. When Postscript and 8 Megabytes or more of RAM are installed, all values are valid, provided I/O Buffering, Mopying, or Ram Disk have not consumed the needed memory. This object is only supported if Postscript is resident in the printer.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2), eAuto(3)  

maximum-resource-saving-memory 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.7
This object's name is misleading. This object returns the maximum amount of additional memory, in bytes, that can be dedicated to holding PDL permanent soft resources. Additional information: NOTE: The values listed below have not been verified on LaserJet 4050 Series. The following numbers assume that IO-BUFFERING=eOff; if IO-BUFFERING<>eOff, the following numbers will be reduced by the value of IO-BUFFER-SIZE. Memory for resource saving is allocated in increments of 102400 bytes. Therefore, for each 1M (1048576 bytes) of memory added to the printer, 102400 bytes are made available to resource saving (and I/O buffering) and 24576 bytes are retained until an additional 102400 byte block can be made available. The value reported by this object is always rounded down to the nearest multiple of 102400. For a PCL-only printer, the value of this object is zero (all resource saving memory is dedicated to PCL). If PostScript is installed without a duplex unit, the value of this object is as follows: Zero if <7M memory is installed. 1048576 if 7M memory is installed and RESOURCE-SAVING=eOff. 1048576 if 7M memory is installed and RESOURCE-SAVING=eOn (note that this value will be reduced by the amount of memory allocated to PCL-RESOURCE-SAVING-MEMORY-SIZE and POSTSCRIPT-RESOURCE-SAVING-MEMORY-SIZE). 819200 if 7M memory is installed and RESOURCE-SAVING=eAuto. When RESOURCE-SAVING=eAuto, 819200 bytes of each 1M over 7M memory installed are allocated to PCL and PostScript (409600 each) with the remaining bytes added to this object. When RESOURCE-SAVING=eOn or eOff, all bytes over 13M memory installed are added to this object. If PostScript is installed with a duplex unit, the value of this object is as follows: Zero if <13M memory is installed. 1048576 if 13M memory is installed and RESOURCE-SAVING=eOff. 1048576 if 13M memory is installed and RESOURCE-SAVING=eOn (note that this value will be reduced by the amount of memory allocated to PCL-RESOURCE-SAVING-MEMORY-SIZE and POSTSCRIPT-RESOURCE-SAVING-MEMORY-SIZE). 1048576 if 13M memory is installed and RESOURCE-SAVING=eAuto. When RESOURCE-SAVING=eAuto, 810200 bytes of each 1M over 13M memory installed are allocated to PCL and PostScript (409600 each) with the remaining bytes added to this object. When RESOURCE-SAVING=eOn or eOff, all bytes over 13M memory installed are added to this object. The above listed values returned by this object will be reduced by the amount of memory added to PCL-RESOURCE-SAVING-MEMORY-SIZE and POSTSCRIPT-RESOURCE-SAVING-MEMORY-SIZE when RESOURCE-SAVING=eOn.
OBJECT-TYPE    
  INTEGER  

default-vertical-black-resolution 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.8
Returns or changes the value of the default vertical black resolution. The units are dots per inch. Additional information: In LaserJet 4050 Series changing this OID also causes DEFAULT- HORIZONTAL-BLACK RESOLUTION to change. DEFAULT- HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are 300 and 600 for LaserJet 8100 Series and LaserJet 8000 Series, and 300, 600, and 1200 for LaserJet 5000 Series and LaserJet 4000 Series. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follow: LaserJet 5000 Series and LaserJet 4000 Series: n < 450 snaps to 300 450 >= n < 900 snaps to 600 n >= 900 snaps to 1200 LaserJet 8100 Series and LaserJet 8000 Series: n < 450 snaps to 300 n >= 450 snaps to 600
OBJECT-TYPE    
  INTEGER  

default-horizontal-black-resolution 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.9
Returns or changes the value of the default horizontal black resolution. The units are dots per inch. Additional information: In LaserJet 4050 Series changing this object also causes DEFAULT-VERTICAL-BLACK RESOLUTION to change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are 300 and 600 for LaserJet 8100 Series and LaserJet 8000 Series, and 300, 600, and 1200 for LaserJet 5000 Series and LaserJet 4000 Series. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follow: LaserJet 5000 Series and LaserJet 4000 Series: n < 450 snaps to 300 450 >= n < 900 snaps to 600 n >= 900 snaps to 1200 LaserJet 8100 Series and LaserJet 8000 Series: n < 450 snaps to 300 n >= 450 snaps to 600
OBJECT-TYPE    
  INTEGER  

default-page-protect 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.10
Returns or changes the default page protection behavior. If eOff, the device does not reserve memory for holding the entire raster form of a processed page. If eOn, then memory is reserved. If eAuto, the device determines the amount of memory to reserve. Additional information: Setting to eOn causes MET to be more conservative, but it will not allocate memory to hold an entire rasterized page.
OBJECT-TYPE    
  INTEGER eOn(2), eAuto(3)  

default-lines-per-page 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.11
Returns or changes the default number of lines per page. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return the . Additional information: The supported values in LaserJet 4050 Series are 5 to 128. Setting to an unsupported value causes the the printer to substitute in a snap value and to return status. The snap values are as follow: <5 snaps to 5 >128 snaps to 128
OBJECT-TYPE    
  INTEGER  

default-vmi 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.12
Returns or changes the default vertical motion index. The unit of measure for VMI is centipoints per line. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return .
OBJECT-TYPE    
  INTEGER  

default-media-size 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.13
This indicates the default media size. A write of an unsupported value causes an . Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document.
OBJECT-TYPE    
  INTEGER eUSExecutive(1), eUSLetter(2), eUSLegal(3), eROC16K(17), eJISExecutive(18), eISOandJISA5(25), eISOandJISA4(26), eMonarch(80), eCommercial10(81), eInternationalDL(90), eInternationalC5(91), eInternationalB5(100), eCustom(101)  

cold-reset-media-size 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.19
Returns or sets the media size that is used as the DEFAULT-MEDIA-SIZE when a cold reset occurs.
OBJECT-TYPE    
  INTEGER eUSLetter(2), eISOandJISA4(26)  

default-media-name 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.22
Returns or sets the media name that is used until the media name is changed by a print job command. Additional information: This string must be one of the MEDIAn-NAME objects. The value of this object is saved across a power cycle.
OBJECT-TYPE    
  DisplayString  

reprint 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.36
Returns or changes the reprint (jam recovery) setting. If eOn, then the device will reprint pages jammed pages. If eOff, the device will not attempt to reprint jammed pages. If eAuto, a device dependent algorithm (which should be documented in the POS) will be used to determine if the page gets reprinted. This object controls all PDLs, unless a specific PDL supports its own reprint control mechanism. To date, only PostScript has a PDL reprint control mechanism. Additional information: Setting this object when the printer is not idle, may cause a status of to be returned, but the new value will not take effect until a job boundary is reached. If a get is done on object before the job boundary is reached, the value last set will be returned. When the value is set to eOff, pages will not be stored in the printer, and in the event of a paper jam, will have to be reprinted. When the value is set to eOn, pages will be stored until delivery, therefore, in the event of a paper jam, the page will be reprinted. When the value is set to eAuto, the printer will behave as though it is eOff when there is less than seven megabytes of memory installed in the printer. When additional memory is installed, to total at least seven megabytes of RAM, the setting of eAuto will behave as though it was set to eOn.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2), eAuto(3)  

wide-a4 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.37
Returns or changes the wide A4 logical page size setting. If eOn, then the margins/printable area of A4 paper will be changed to allow 80 10-pitch characters to be printed on a single line. If eOff then the industry standard A4 logical page size is used.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2)  

dark-courier 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.38
Returns or changes the dark Courier setting. If eOn, then the Courier font used will approximate the same darkness as the LaserJet III printer. If eOff, then the Courier font used will approximate the same darkness as the LaserJet 4 printer.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2)  

default-bits-per-pixel 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.39
Controls the number of levels used (per pixel) when printing grayscale or color images.
OBJECT-TYPE    
  INTEGER  

pcl-datecode 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.1
This indicates the PCL firmware date code in yyyymmdd format.
OBJECT-TYPE    
  DisplayString  

pcl-resource-saving-memory-size 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.2
Returns or changes the amount of resource saving memory set aside to hold permanent soft PCL resources. Additional information: The value returned by this object is the amount of Resource Saving memory currently dedicated to PCL. For a PCL-only printer, the value of this object is zero. All memory is dedicated to PCL, but it is not shown as such. If Postscript is installed, the default value of this object is as follows: 0 if RESOURCE-SAVING = eOff. 0 if less than 8 Megabytes of RAM is in the printer. 400K bytes if RAM >= 8 Megabytes and RESOURCE-SAVING = eOn. 400K bytes if RAM = 8 Megabytes and RESOURCE-SAVING = eAuto, plus 100K bytes for each Megabyte of RAM over 8 Megabytes. If RESOURCE-SAVING=eOn, this object can be used to set the amount of Resource Saving memory currently dedicated to PCL. The range of values supported by this object are: 0 bytes (which disables resource saving for PCL) 400K bytes through (400K bytes + MAXIMUM-RESOURCE-SAVING-MEMORY) in increments of 100K bytes. If a value is received that is greater than 0 and less than 400K bytes, it will be snapped to 400K bytes and a status of returned. If an unsupported value greater than 400K bytes is received, it will be snapped down to the nearest 100K value and a status of returned. Attempting to set this object when RESOURCE-SAVING is eAuto or eOff will cause a status of to be returned.
OBJECT-TYPE    
  INTEGER  

pcl-name 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.3
Contains the name of the PDL. For PCL, the name is `PCL'.
OBJECT-TYPE    
  DisplayString  

pcl-version 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.4
Contains the PDL version.
OBJECT-TYPE    
  DisplayString  

pcl-total-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.5
Total number of PCL pages printed by the device. Additional information: In LaserJet 4050 Series the PCL page count is kept in NVRAM, and the NVRAM value is updated at least every 10 pages. NOTE: The value returned by this object will be incremented every page but if power is lost between NVRAM updates, up to 9 pages of the page count may be lost. The page count counter will be reset to zero after 16,777,215 (2^24-1) pages. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by two.
OBJECT-TYPE    
  INTEGER  

pcl-default-symbol-set 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.11
Returns or changes the default PCL symbol set. The enumeration values match the values supported by the PCL Symbol Set Code escape sequence, *c#R. The binary representation of the enumerated value is also matches the PML . Additional information: The eWindows31J enumeration is only supported if a Japanese font SIMM is installed.
OBJECT-TYPE    
  INTEGER eISO60DanishNorwegian(4), eISO15Italian(9), eISO88591Latin1ECMA94(14), eISO11SwedishforNames(19), eISO6ASCII(21), eISO4UnitedKingdom(37), eISO69French(38), eISO21German(39), eLegal(53), eISO88592Latin2ECMA94(78), eISO17Spanish(83), ePSMath(173), eISO88599Latin5ECMA128(174), eWindows31Latin5(180), eMicrosoftPublishing(202), eVenturaMath(205), eDeskTop(234), eMath8(269), eRoman8(277), eWindows31Latin2(293), ePC8Turkish(308), eWindows30Latin1(309), ePSText(330), ePC8CodePage437(341), ePC8DNDanishNorwegian(373), ePC850Multilingual(405), eVenturaInternational(426), eVenturaUS(458), ePiFont(501), ePC852Latin2(565), eWindows31J(619), eWindows31Latin1(629)  

pcl-default-font-height 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.13
Returns or changes the default PCL height. Height is an approximate measure of the body of the type in centipoints. A centipoint is 1/7200 inch. Height applies only to proportional fonts. Point size, in points, can be converted to font height, in centipoints, by multiplying the point size by 100. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return . ''Closest'' means the smallest absolute difference. Additional information: Supported values range from 400 to 99975, in increments of 25 units. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follow: <=400 snaps to 400 >=99975 snaps to 99975 Unsupported values in the range 400 to 99975 snap DOWN to the previous supported value (i.e 25293 snaps to 25275 or 75038 snaps to 75025).
OBJECT-TYPE    
  INTEGER  

pcl-default-font-source 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.14
Returns or changes the value of the default font source variable in NVRAM.
OBJECT-TYPE    
  INTEGER eInternal(1), ePermanentSoft(2), eRomSimm1(10), eRomSimm2(11), eRomSimm3(12), eRomSimm4(13)  

pcl-default-font-number 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.15
Returns or changes the value of the default font number variable in NVRAM. Writing an unsupported value causes the printer to generate an . Additional information: Valid numbers or 0 - 255, but only font numbers that are included in the PCL FONT LIST are selectable.
OBJECT-TYPE    
  INTEGER 0..255  

pcl-default-font-width 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.16
Returns or changes the default PCL font width. Width is expressed as the width of a character in centipoints. A centipoint is 1/7200 inch. Width applies only to fixed space fonts. Pitch, in character per inch, can be converted to font width, in centipoints, by dividing 7200 by the pitch. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return . ''Closest'' means the smallest absolute difference. Additional information: Setting to an unsupported value causes the printer to substitue in a snap value (listed below) and return status. The snap values for pitch are as follow: <=44 snaps to 44 >=9999 snaps to 9999
OBJECT-TYPE    
  INTEGER  

postscript-datecode 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.1
This indicates the PostScript firmware datecode in yyyymmdd format. Additional information: This object is only supported if PostScript option is installed. Returns status if attempting to perform a Get on this OID with no PostScript option installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no PostScript option installed.
OBJECT-TYPE    
  DisplayString  

postscript-resource-saving-memory-size 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.2
Returns or changes the amount of resource saving memory set aside to hold permanent soft PostScript resources. Additional information: The value returned by this object is the amount of Resource Saving memory currently dedicated to Postscript. If Postscript is installed, the default value of this object is as follows: 0 if RESOURCE-SAVING = eOff. 0 if less than 8 Megabytes of RAM is in the printer. 400K bytes if RAM >= 8 Megabytes and RESOURCE-SAVING = eOn. 400K bytes if RAM = 8 Megabytes and RESOURCE-SAVING = eAuto, plus 100K bytes for each Megabyte of RAM over 8 Megabytes. If RESOURCE-SAVING=eOn, this object can be used to set the amount of Resource Saving memory currently dedicated to PCL. The range of values supported by this object are: 0 bytes (which disables resource saving for Postscript) 400K bytes through (400K bytes + MAXIMUM-RESOURCE-SAVING-MEMORY) in increments of 100K bytes. If a value is received that is greater than 0 and less than 400K bytes, it will be snapped to 400K bytes and a status of returned. If an unsupported value greater than 400K bytes is received, it will be snapped down to the nearest 100K value and a status of returned. Attempting to set this object when RESOURCE-SAVING is eAuto or eOff will cause a status of to be returned.
OBJECT-TYPE    
  INTEGER  

postscript-name 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.3
Contains the name of the PDL. For PostScript, the name is `PostScript'. Additional information: This object is only supported if PostScript option is installed. Returns status if attempting to perform a Get on this OID with no PostScript option installed. Returns an status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no PostScript option installed.
OBJECT-TYPE    
  DisplayString  

postscript-version 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.4
Contains the PDL version. Additional information: This object is only supported if PostScript option is installed. Returns status if attempting to perform a Get on this OID with no PostScript option installed. Returns an status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no PostScript option installed.
OBJECT-TYPE    
  DisplayString  

postscript-total-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.5
Total number of PostScript pages printed by the device. Additional information: This object is only supported if the PostScript option is installed. In LaserJet 4050 Series the count is kept in NVRAM, and the NVRAM value is updated at least every 10 sheets. NOTE: The value returned by this object will be incremented every sheet but if power is lost between NVRAM updates up to 9 sheets of the count may be lost. The counter will be reset to zero after 16,777,215 (2^24-1) pages.
OBJECT-TYPE    
  INTEGER  

postscript-print-errors 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.11
Returns or changes the value of the print PostScript errors setting. If eOn, PostScript prints an error page showing the error encountered and the stack at the time of the error. Additional information: This object is only supported if the PostScript option is installed.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2)  

postscript-jam-recovery 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.12
Returns or changes the PostScript jam recovery setting. If eOn, then the device will reprint PostScript pages, if those pages jam. Additional information: This object is only supported if PostScript option is installed.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2)  

esc-p-datecode 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.5.1
This indicates the ESC-P PDL datecode. The datecode format is yyyymmdd. Additional information: This object is only supported if ESC-P option is installed. Returns an status if attempting to perform a Get on this OID with no ESC-P option installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no ESC-P option installed.
OBJECT-TYPE    
  DisplayString  

esc-p-name 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.5.3
Contains the name of the PDL. For ESC-P, the name is `ESC-P'. Additional information: This object is only supported if ESC-P option is installed. Returns an status if attempting to perform a Get on this OID with no ESC-P option installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no ESC-P option installed.
OBJECT-TYPE    
  DisplayString  

esc-p-version 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.5.4
Contains the PDL version. Additional information: This object is only supported if ESC-P option is installed. Returns an status if attempting to perform a Get on this OID with no ESC-P option installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no ESC-P option installed.
OBJECT-TYPE    
  DisplayString  

pjl-password 1.3.6.1.4.1.11.2.3.9.4.2.1.3.5.1
Returns PJL password, if the password is not set (zero). If the password is set, then attempting to retrieve the password causes an to occur and will return the .
OBJECT-TYPE    
  INTEGER  

not-ready-destination-print-engine 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.1
Indicates if the print engine sub-system in the device is not ready. If there are no items in the collection (i.e. no bits are set), then the print engine sub- system is ready. If there is an item present, then the item indicates what is causing the print engine sub- system to be not ready. cDoorOpen is in the collection if one or more access panels are open. If the device contains more than one access panel, then NOT-READY- PRINT-ENGINE-DOOR indicates which access panel(s) are open. cInternalMediaJam is in the collection if one or more pieces of media are jammed inside the device. If the media is jammed at an input tray, cTrayMediaJam is in the collection, and if the device has more than one input tray, then NOT-READY-MEDIA-JAM-AT-TRAY indicates which tray has a media jam. If the media is jammed at an output bin, cBinMediaJam is in the collection, and if the device has more than one output bin, then NOT-READY- MEDIA-JAM-AT-BIN indicates which bin has a media jam. cRequestedMediaUnavailable is in the collection if the current print job requires media that is not available. cTrayEmpty is in the collection if the current print job requires media from an input tray that is empty. If the device has more than one input tray, then NOT-READY- TRAY-EMPTY indicates which tray is empty. cOutputBinFull is in the collection if an output bin is full. If the device has more than one output bin, then NOT-READY-BIN-FULL indicates which bin is full. cManualFeedMedia is in the collection if the device is waiting for media to manually be fed. cMarkingAgentMissing is in the collection if a marking agent (toner cartridge, ink pen, etc.) is missing. If the device has more than one marking agent, then NOT- READY-MARKING-AGENT-MISSING indicates which marking agent is missing. cMarkingAgentOut is in the collection if the device is not ready due to one or more marking agents being low or out. If the device has more than one marking agent, then NOT-READY-MARKING-AGENT-LOW-OR- OUT indicates which marking agent is low or out. cIncorrectMarkingAgent is in the collection if the device detects that an incorrect marking agent is installed. If the device has more than one marking agent, then NOT-READY-INCORRECT-MARKING-AGENT indicates which marking agent location is loaded with the wrong type of marking agent. cTrayMissing is in the collection if the device is not ready because one or more trays are not installed. If the device has more than one input tray, then NOT-READY-TRAY-MISSING indicates which tray is missing. cDeviceSpecific is in the collection if one or more items are in either NOT- READY-LASER-PRINT-ENGINE or NOT-READY-DESTINATION- INKJET-PRINT-ENGINE-NOT-READY. cMediaPickMisfeed is in the collection if the print engine detects the tray is not empty, but can not pick up a sheet of media from that tray. cMarkingAgentFailure indicates there is a failure with a marking agent and it may need to be replaced. If the device supports more than one marking agent, then the NOT-READY-MARKING-AGENT-FAILURE object indicates all the marking agents that have failed. The POS will indicate the marking agent failure recovery process, if any.
OBJECT-TYPE    
  STRING  

not-ready-laser-print-engine 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.3
Indicates if the laser print engine sub-system in the device is not ready. If there are no items in the collection (i.e. no bits are set), then the laser print engine sub-system is ready. If there is an item present, then the item indicates what is causing the laser print engine sub-system to be not ready.
OBJECT-TYPE    
  STRING  


total-color-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.7
Total number of color pages printed by the device. Additional information: Any page with one or more color pixels is counted as a color page. Pages that only contain black marks are not counted by this object. The counter will roll over to zero after 4,294,967,296 pages. Each side of a duplexed sheet of media will be counted independently based on the criteria listed above.
OBJECT-TYPE    
  INTEGER 0..4294967296  

default-manual-feed 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.4
Returns or changes the default manual feed value used by the PDLs.
OBJECT-TYPE    
  INTEGER eOff(1), eOn(2)  

mp-tray 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.5
Returns or changes the value of the multi-purpose (MP) tray configuration variable. The MP tray can be configured to operate as an additional input tray (eCassette), a manual feed slot (eManual), or in a manner compatible with the LaserJet III manual feed slot (eFirst). If configured for eFirst, if media is present in the MP tray, that media is used (assuming the size matches and the print job didn't specify another tray) until the MP tray is empty. Additional information: The MP tray can be configured for use either as a paper cassette or as a priority manual feed tray. When the tray is configured as a manual feed tray, unsolicited status messages are not generated when there is no paper in the tray. LaserJet 4050 Series will pull media from TRAY 1 only if there is a sheet present and it matches the needed size and type.
OBJECT-TYPE    
  INTEGER eCassette(2), eFirst(3)  

tray-lock 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.6
Returns or changes the list of locked input trays. The printer only pulls media from a locked input tray when the input tray is specifically requested by the print job. Additional information: The HP LaserJet 2100 Series will pull paper from a locked tray if that tray is specifically requested or if the user presses the Go button on a paper mount override and there is no paper available in an unlocked tray. There must always be at least one unlocked tray. When no optional lower cassette is installed and one tray is locked, an attempt to lock the other tray will result in the first tray unlocking. When the optional cassette is installed and two trays are locked, an attempt to lock the third will fail with a return status of and a return value containing the collection of previously locked trays.
OBJECT-TYPE    
  STRING  

not-ready-tray-missing 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.2.1
Indicates which trays are not currently installed that is caused the device to be not ready.
OBJECT-TYPE    
  STRING  

not-ready-tray-empty 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.2.2
Indicates which trays contain no media causing the device to be not ready. Some devices may treat tray missing as a tray empty condition.
OBJECT-TYPE    
  STRING  

status-tray-missing 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.2.3
Indicates which trays are not currently installed that is caused the device to be in a warning condition.
OBJECT-TYPE    
  STRING  

status-tray-empty 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.2.4
Indicates which trays contain no media causing the device to be in a warning condition. Some devices may treat tray missing as a tray empty condition.
OBJECT-TYPE    
  STRING  

low-marking-agent-processing 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1.3
Returns or changes how the device processes a low marking agent event. If eCont, then the device continues to print. If eStop, then the device stops until a continue event occurs.
OBJECT-TYPE    
  INTEGER eStop(1), eCont(2)  

default-ret 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6.5
Returns or changes the Resolution Enhancement Technology setting. Devices that only support eOff and on should map all other values to on and always return the same non-eOff value to indicate on. The list of supported values should be documented in the device POS. Additional information: Setting this object may cause a status of to be returned, but the new value will not take effect until a job boundary is reached. If a get is done on object before the job boundary is reached, the value last set will be returned. The value of this object is saved over a powercycle.
OBJECT-TYPE    
  INTEGER eOff(1), eLight(2), eMedium(3), eDark(4)  

default-print-quality 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6.7
Returns or sets the default print quality. A value of zero has the lowest print quality. A value of 100 has the highest print quality. Each POS should document what values in the 0 to 100 range are supported. Additional information: In LaserJet 4050 Series, the supported values are 0 and 100. A value of zero has the lowest print quality(ECONOMODE=ON), thus minimizes the amount of toner used to print a page. A value of 100 has the highest print quality (ECONOMODE=OFF), thus uses more toner to print a page. Setting to an unsupported value outside of the 0 to 100 range causes the printer to return status. Setting to an unsupported value inside of the 0 to 100 range causes the printer to substitute in a snap value (listed below) and to return status. The snap values are as follow: 0 to 50 snap to 0 51 to 100 snap to 100
OBJECT-TYPE    
  INTEGER 0..100  

hrstorageindex 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.1
A unique value for each logical storage area contained by the host. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (mass storage) : Constant. The index is assigned by the person controlling the printer object definition. The value of the hrFileSystemStorageIndex and the index of the prtStorageRefIndex use the value of this object's index. The value of the object matches the value of the object's index. Returns status if attempting to perform a get on this OID with no mass storage device installed. This first volume installed will be number 2, followed by the second. IDE will always be 2. If ram disk and flash disk are installed then Flash disk will be 2 followed by ram disk. The Storage types are: IDE (EIO DISK), Flash Disk, Ram Disk
OBJECT-TYPE    
  INTEGER 1..2147483647  

hrstoragetype 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.2
The type of storage represented by this entry. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (mass storage): Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed. HRMhrStorageFixedDisk is 1.3.6.1.2.1.25.2.1.4
OBJECT-TYPE    
  OBJECT IDENTIFIER  

hrstoragedescr 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.3
A description of the type and instance of the storage described by this entry. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : This object is not localized. Additional information (mass storage) : This string indicates the location of the installed mass storage device. The supported values are: 'Flash disk in DIMM slot 1' 'Flash disk in DIMM slot 2' 'Flash disk in DIMM slot 3' 'Disk in EIO 1' 'Disk in EIO 2' 'Disk in EIO 3' 'Static RAM disk using system memory' Applications determine the location of the installed mass storage device by getting this object. This string is not localized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  STRING  

hrstorageallocationunits 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.4
The size, in bytes, of the data objects allocated from this pool. If this entry is monitoring sectors, blocks, buffers, or packets, for example, this number will commonly be greater than one. Otherwise this number will typically be one. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : Unit is one byte. Additional information (mass storage) : Returns the value 1024 if the file system is not initialized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER 1..2147483647  

hrstorageused 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.6
The amount of the storage represented by this entry that is allocated, in units of hrStorageAllocationUnits. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: This object returns the amount of memory in use by the printer at the current time. This object should not be used when creating a print job for the device because the amount of memory in use will likely be different when the printer processes the print job. Additional information (mass storage) : Applications can determine the amount of used space on the installed mass storage device by getting the hrStorageAllocationUnits object and this object. The amount of used space is these two returned values multiplied together. Returns the value 0 if the file system is not initialized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER 0..2147483647  

hrstorageallocationfailures 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.7
The number of requests for storage represented by this entry that could not be honored due to not enough storage. It should be noted that as this object has a SYNTAX of Counter, that it does not have a defined initial value. However, it is recommended that this object be initialized to zero. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer): This object is set to zero at power on and when any reset is done via prtGeneralReset. This object is incremented whenever the printer is short on memory (codewise: when PersMemoryCycle is called with a parameter of 2). Additional information (mass storage): Total number of writes that failed since power on) due to the mass storage device being full. Returns the value 0 when the file system has not been initialized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER  

hrdeviceindex 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.1
A unique value for each device contained by the host. The value for each device must remain constant at least from one re-initialization of the agent to the next re-initialization. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer): The entry in the Device Table which describes the printer. Additional information (mass storage): Constant. The index is assigned by the person controlling the printer object definition. All device/mass storage/file system/partition tables in Host Resources MIB and the Printer MIB that relate to the mass storage device use the same index value. The value of the index of the following objects is this object's value: prtDeviceRefIndex hrDiskStorageIndex hrPartitionIndex hrFSIndex The value of the object matches the value of the object's index. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER 1..2147483647  

hrdevicetype 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.2
An indication of the type of device. If this value is `hrDeviceProcessor { hrDeviceTypes 3 }' then an entry exists in the hrProcessorTable which corresponds to this device. If this value is `hrDeviceNetwork { hrDeviceTypes 4 }', then an entry exists in the hrNetworkTable which corresponds to this device. If this value is `hrDevicePrinter { hrDeviceTypes 5 }', then an entry exists in the hrPrinterTable which corresponds to this device. If this value is `hrDeviceDiskStorage { hrDeviceTypes 6 }', then an entry exists in the hrDiskStorageTable which corresponds to this device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (mass storage): Constant. Applications should determine if a mass storage device is installed by getting this object. If the response is something other than HRMhrDeviceDiskStorage, the application knows this row in the hrDeviceTable does not refer to a mass storage object. Due to restrictions placed on this object by the Host Resources Disk Table, the value of this object must be HRMhrDeviceDiskStorge. Returns status if attempting to perform a Get on this OID with no mass storage device installed. HRMhrDeviceDiskStorage is 1.3.6.1.2.1.25.3.1.6
OBJECT-TYPE    
  OBJECT IDENTIFIER  

hrdevicestatus 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.5
The current operational state of the device described by this row of the table. A value unknown(1) indicates that the current state of the device is unknown. running(2) indicates that the device is up and running and that no unusual error conditions are known. The warning(3) state indicates that agent has been informed of an unusual error condition by the operational software (e.g., a disk device driver) but that the device is still 'operational'. An example would be high number of soft errors on a disk. A value of testing(4), indicates that the device is not available for use because it is in the testing state. The state of down(5) is used only when the agent has been informed that the device is not available for any use. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : The printer's condition is mapped as follows (printer): eHrunning -- Printer ready to print or is printing. May be in power save mode. eHwarning -- A condition exists that needs attention but it is not currently preventing printing. A non-critical alert is active. eHdown -- Printer is not printing because it is offline or a critical alert is active. Human interaction is needed to bring the printer to a ready state. Additional information (mass storage) : Returns mass storage device status information. running -- mass storage device functional. May be in power save mode. warning -- The mass storage device failed a self-test but completed the power-on initialization sequence. The mass storage device is readable even when the mass storage device fails the power-up self-test in order to give the customer a chance to retrieve any data that can be made available. testing -- Mass storage device is executing a test. down -- Mass storage device is non-functional. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER eHrunning(2), eHwarning(3), eHdown(5)  

hrprinterstatus 1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1.1
The current status of this printer device. When in the idle(1), printing(2), or warmup(3) state, the corresponding hrDeviceStatus should be running(2) or warning(3). When in the unknown state, the corresponding hrDeviceStatus should be unknown(1). Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The printer's condition is mapped as follows: eHother -- The printer is offline or a critical alert is active. eHidle -- The printer is not doing any of the items listed below for eHprinting status. eHprinting -- A job is currently being processed or printed or a PJL job is being processed. eHwarmup -- If hrDeviceStatus is eHdown, then the printer is currently offline but is resolving the condition that caused it be offline. If hrDeviceStatus is eHrunning, then the printer was in power save mode and is now ready ready to print.
OBJECT-TYPE    
  INTEGER eHother(1), eHidle(3), eHprinting(4), eHwarmup(5)  

hrprinterdetectederrorstate 1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1.2
This object represents any error conditions detected by the printer. The error conditions are encoded as bits in an octet string, with the following definitions: Condition Bit # hrDeviceStatus lowPaper 0 warning(3) noPaper 1 down(5) lowToner 2 warning(3) noToner 3 down(5) doorOpen 4 down(5) jammed 5 down(5) offline 6 down(5) serviceRequested 7 warning(3) If multiple conditions are currently detected and the hrDeviceStatus would not otherwise be unknown(1) or testing(4), the hrDeviceStatus shall correspond to the worst state of those indicated, where down(5) is worse than warning(3) which is worse than running(2). Bits are numbered starting with the most significant bit of the first byte being bit 0, the least significant bit of the first byte being bit 7, the most significant bit of the second byte being bit 8, and so on. A one bit encodes that the condition was detected, while a zero bit encodes that the condition was not detected. This object is useful for alerting an operator to specific warning or error conditions that may occur, especially those requiring human intervention. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: LaserJet 4050 Series reports error conditions as follows: lowPaper -- A tray is empty, but the media to be loaded is not currently needed. hrDeviceStatus = eHwarning; hrPrinterStatus = eHidle or eHprinting; A non-critical alert is active. noPaper -- A tray is empty and must be filled for printing to continue. hrDeviceStatus = eHdown; hrPrinterStatus = eHother; A critical alert is active. lowToner -- Toner is almost gone. The quality of printed pages will begin to deteriorate until the toner is completely gone. hrDeviceStatus = eHwarning; hrPrinterStatus = eHidle or eHprinting; A non-critical alert is active. noToner -- LaserJet 4050 Series printers do not report this condition. coverOpen -- A printer cover or door is open. hrDeviceStatus = eHdown; hrPrinterStatus = eHother; A critical alert is active. jammed -- Paper is jammed and the printer will be unable to continue printing until the jam is cleared. hrDeviceStatus = eHdown; hrPrinterStatus = eHother; A critical alert is active. offline -- Printer is offline and will not accept new print jobs until it is online again. hrDeviceStatus = eHdown; hrPrinterStatus = eHother; A critical alert is active. serviceRequested -- Any status or error condition not listed above. If the condition prevents printing, the 'offline' bit is also set and the hrDeviceStatus and hrPrinterStatus listed for offline above are returned. hrDeviceStatus = eHwarning; hrPrinterStatus = eHidle or eHprinting; A non-critical alert is active.
OBJECT-TYPE    
  STRING  

prtgeneralconfigchanges 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.1
Counts configuration changes that change the capabilities of a printer, such as the addition/deletion of input/output bins, the addition/deletion of interpreters, or changes in media size. Such changes will often affect the capability of the printer to service certain types of print jobs. Management applications may cache infrequently changed configuration information about sub-units on the printer. This object should be incremented whenever the agent wishes such applications to invalidate that cache and re-download all of this configuration information, thereby signaling a change in the printer's configuration. For example, if an input tray that contained paper of different dimensions was added, this counter would be incremented. As an additional example, this counter would not be incremented when an input tray is removed or the level of an input device changes. Refer to Standard Printer MIB for more details. Additional information: This is a 32 bit counter (unsigned). When it reaches its maximum value, it will roll to zero.
OBJECT-TYPE    
  INTEGER 0..2147483648  

prtgeneralcurrentlocalization 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.2
The value of the prtLocalizationIndex corresponding to the current language, country, and character set to be used for localized string values that are identified as being dependent on the value of this object. Note that this object does not apply to localized strings in the prtConsole group or to any object that is not explicitly identified as being localized according to prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details. Additional information: The value of this object is saved in NVRAM.
OBJECT-TYPE    
  INTEGER 1..17  

prtgeneralreset 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.3
Setting this value to `powerCycleReset', `resetToNVRAM', or `resetToFactoryDefaults' will result in the resetting of the printer. When read, this object will always have the value `notResetting(3)', and a SET of the value `notResetting' shall have no effect on the printer. Some of the defined values are optional. However, every implementation must support at least the values `notResetting' and 'resetToNVRAM'. Refer to Standard Printer MIB for more details. Additional information: Replaces PML USER-NVRAM-RESET and POWER-ON-RESET. The, the following sequence of events occur when this object is set to ePpowerCycleReset, ePresetToNVRAM, or ePresetToFactoryDefaults: 1. Wait until a job boundary. 2. The paper path is flushed. 3. The printer is reset per the request. The printer will respond to PML requests up to this point in time. All settings will make the printer go thru its power-on initialization routines and I/O cards are reset. When this object is set to ePpowerCycleReset or ePresetToNVRAM, the printer performs its power on initialization routines. I/O cards are reset, although NVRAM on the cards is not changed, and all I/O buffers are flushed. This is equivalent to turning the printer off and then on again. Setting this object to ePresetToFactoryDefaults causes the same action as ePpowerCycleReset exept that it also changes all configurable settings back to their factory defaults. It is equivalent to doing a Cold Reset from the control panel while turning on the printer.
OBJECT-TYPE    
  INTEGER ePnotResetting(3), ePpowerCycleReset(4), ePresetToNVRAM(5), ePresetToFactoryDefaults(6)  

prtgeneralcurrentoperator 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.4
The name of the person who is responsible for operating this printer. It is suggested that this string include information that would enable other humans to reach the operator, such as a phone number. As a convention to facilitate automatic notification of the operator by the agent or the network management station, the phone number, fax number or email address should be placed on a separate line starting with ASCII LF (hex 0x0A) and the ASCII text string (without the quotes): 'phone: ', 'fax: ', and 'email: ', respectively. Phone numbers may contain digits, whitespace and parentheses, which shall be ignored. Phone numbers may also include ASCII comma characters(hex 2C) that are used to indicate a two-second pause during the dialing sequence. If either the phone, fax, or email information is not available, then a line should not be included for this information. NOTE: For interoperability purposes, it is advisable to use email addresses formatted according to RFC 822 requirements. Refer to Standard Printer MIB for more details. Additional information: Replaces PML SYSTEM-CONTACT. The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user entered string is too long, the device will store as much as possible and will return the status.
OBJECT-TYPE    
  STRING Size(0..32)  

prtgeneralserviceperson 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.5
The name of the person responsible for servicing this printer. It is suggested that this string include information that would enable other humans to reach the service person, such as a phone number. As a convention to facilitate automatic notification of the service person by the agent or a network management station, the phone number, fax number or email address should be placed on a separate line starting with ASCII LF (hex 0x0A) and the ASCII text string (without the quotes): 'phone: ', 'fax: ', and 'email: ', respectively. Phone numbers may contain digits, whitespace and parentheses, which shall be ignored. Phone numbers can also include one or more ASCII comma characters(hex 2C) to indicate a two-second pause during the dialing sequence. If either the phone,fax, or email information is not available, then a line should not included for this information. NOTE: For interoperability purposes, it is advisable to use email addresses formatted according to RFC 822 requirements. Refer to Standard Printer MIB for more details. Additional information: Replaces PML SYSTEM-CONTACT. The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user entered string is too long, the device will store as much as possible and will return the status.
OBJECT-TYPE    
  STRING Size(0..32)  

prtconsolelocalization 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.10
The value of the prtLocalizationIndex corresponding to the language, country, and character set to be used for the console. This localization applies both to the actual display on the console as well as the encoding of these console objects in management operations. Refer to Standard Printer MIB for more details. Additional information: The value of this object is saved in NVRAM. If a localized string is currently being displayed on the control panel by the device, changing this object will cause the displayed string to be changed to its new value. If this object is changed while the printer is processing a page that contains localized strings, the results are undefined.
OBJECT-TYPE    
  INTEGER 1..17  

prtconsolenumberofdisplaylines 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.11
The number of lines on the printer's physical display. This value is 0 if there are no lines on the physical display or if there is no physical display Refer to Standard Printer MIB for more details. Additional information: The printer has two physical lines on the display, however, in many cases up to four seperate lines of text may be displayed by alternating pairs of lines every three seconds. Thus the display really has four logical lines for displaying messages. This object will return the number of logical display lines supported by the printer.
OBJECT-TYPE    
  INTEGER 0..65535  

prtconsolenumberofdisplaychars 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.12
The number of characters per line displayed on the physical display. This value is 0 if there are no lines on the physical display or if there is no physical display Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER 0..65535  

prtconsoledisable 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.13
If the object prtConsoleDisable has value 'operatorConsoleDisabled' then input is not accepted from the operator console. If the object prtConsoleDisable has the value 'operatorConsoleEnabled' then input is accepted from the operator console. If the object prtConsoleDisable has the value 'operatorConsoleEnabledLevel1','operatorConsoleEnabledLevel2' or 'operatorConsoleEnabledLevel3' then limited input is accepted from the operator console; the limitations are product specific, however, the limitations are generally less restrictive for operatorConsoleEnabledLevel1 than for operatorConsoleEnabledLeve2, which is less restrictive than operatorConsoleEnabledLevel3. The value of the prtConsoleDisable object is a type-2 enumeration. Refer to Standard Printer MIB for more details. Additional information: If the object prtConsoleDisable has value 'ePoperatorConsoleDisabled' then manual input is not accepted from the operator console. If the object prtConsoleDisable has the value 'ePoperatorConsoleEnabled' then manual input is accepted from the operator console. The following menus are locked with these corresponding values: ePoperatorConsoleEnabled (no locking) ePoperatorConsoleEnabledLevel1 (minimal locking) RESETS MENU CONFIGURATION MENU I/O MENU ePoperatorConsoleEnabledLevel2 (moderate locking) PRINT QUALITY MENU PAPER HANDLING MENU menus in level 1 ePoperatorConsoleDisabled (maximum locking) PRINTING MENU INFORMATION MENU Job Cancel menus in levels 1 and 2
OBJECT-TYPE    
  INTEGER ePoperatorConsoleEnabled(3), ePoperatorConsoleDisabled(4), ePoperatorConsoleEnabledLevel1(5), ePoperatorConsoleEnabledLevel2(6)  

prtgeneralstartuppage 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.14
Used to enable or disable printing a startup page. If enabled, a startup page will be printed shortly after power-up, when the device is ready. Typical startup pages include test patterns and/or printer configuration information. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER ePnotPresent(5)  

prtgeneralbannerpage 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.15
Used to enable or disable printing banner pages at the beginning of jobs. This is a master switch which applies to all jobs, regardless of interpreter. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER ePnotPresent(5)  

prtgeneralprintername 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.16
An administrator-specified name for this printer. Depending upon implementation of this printer, the value of this object may or may not be same as the value for the MIB-II 'SysName' object. Refer to Standard Printer MIB for more details. Additional information: The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user-entered string is too long, the device will store as much as possible and will return the status. The value of this object is saved over a power cycle.
OBJECT-TYPE    
  STRING Size(0..32)  

prtgeneralserialnumber 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.17
A recorded serial number for this device that indexes some type device catalog or inventory. This value is usually set by the device manufacturer but the MIB supports the option of writeability for this object for site-specific administration of device inventory or tracking. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  STRING Size(0..10)  

prtalertcriticalevents 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.18
A running counter of the number of critical alert events that have been recorded in the alert table. The value of this object is RESET in the event of a power cycle operation (i.e., the value is not persistent. Refer to Standard Printer MIB for more details. Additional information: This object is set to zero every time the printer is turned on.
OBJECT-TYPE    
  INTEGER  

prtalertallevents 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.19
A running counter of the total number of alert event entries (critical and non-critical) that have been recorded in the alert table Refer to Standard Printer MIB for more details. Additional information: This object is set to zero every time the printer is turned on. (It is not persistent through a power-cycle.)
OBJECT-TYPE    
  INTEGER  

prtlocalizationlanguage 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.2
A two character language code from ISO 639. Examples en, gb, ca, fr, de. Refer to Standard Printer MIB for more details. Additional information: The languages supported by LaserJet 4050 Series are English, French, German, Italian, Spanish, Swedish, Danish, Norwegian, Dutch, Finnish, Portuguese, Turkish, Polish, Japanese, Russian, Czech, and Hungarian.
OBJECT-TYPE    
  STRING Size(0..2)  

prtlocalizationcountry 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.3
A two character country code from ISO 3166, a blank string (two space characters) shall indicate that the country is not defined. Examples: US, FR, DE, ... Refer to Standard Printer MIB for more details. Additional information: The languages supported by LaserJet 4050 Series (and corresponding country) are English (US, United States), French (FR, France), German (DE, Germany), Italian (IT, Italy), Spanish (ES, Spain), Swedish (SE, Sweden), Danish (DK, Denmark), Norwegian (NO, Norway), Dutch (NL, Netherlands), Finnish (FI, Finland), Portuguese (PT, Portugal), Turkish (TR, Turkey), Polish (PL, Poland), Japanese (JP, Japan), Russian, (RU, Russia), Czech (CS, Czechoslovakia), Hungarian (HU, Hungary)
OBJECT-TYPE    
  STRING Size(0..2)  

prtlocalizationcharacterset 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.4
The coded character set used for this localization. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER ePcsHPRoman8(2004), ePcsISOLatin2(5), ePcsISOLatin5(12), ePcsWindows31J(2024), ePcsISOLatinCyrillic(8)  

prtstoragerefindex 1.3.6.1.4.1.11.2.3.9.4.2.2.5.2.1.2
The value of the hrDeviceIndex of the printer device that this storageEntry is associated with. Refer to Standard Printer MIB for more details. Additional information (mass storage): Constant. The index value indicates the hrStorageTable index for this storage device. The value indicates the hrDeviceTable index for the printer which uses this storage device. Returns status if attempting to perform a Get on this OID with no storage device is installed.
OBJECT-TYPE    
  INTEGER 1..65535  

prtdevicerefindex 1.3.6.1.4.1.11.2.3.9.4.2.2.5.3.1.2
The value of the hrDeviceIndex of the printer device that this deviceEntry is associated with. Refer to Standard Printer MIB for more details. Additional information (mass storage) : Constant. The index indicates the hrDeviceIndex for this mass storage device. The value indicates the hrDeviceIndex for the printer which uses this mass storage device. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER 1..65535  

prtmarkeraddressabilityfeeddir 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.9
The maximum number of addressable marking positions in the feed direction per 10000 units of measure specified by prtMarkerAddressabilityUnit. A value of (-1) implies 'other' or 'infinite' while a value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: This object indicates the value of the resolution (dots per inch) setting for the printer. LaserJet 5000 Series and LaserJet 4000 Series support 300, 600 and 1200 dots per inch. LaserJet 8100 Series and LaserJet 8000 Series supports 300 or 600 dots per inch. 600 dots per inch is the default.
OBJECT-TYPE    
  INTEGER  

prtmarkeraddressabilityxfeeddir 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.10
The maximum number of addressable marking positions in the cross feed direction in 10000 units of measure specified by prtMarkerAddressabilityUnit. A value of (-1) implies 'other' or 'infinite' while a value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: This object indicates the value of the resolution (dots per inch) setting for the printer. LaserJet 5000 Series and LaserJet 4000 Series support 300, 600 and 1200 dots per inch. LaserJet 8100 Series and LaserJet 8000 Series supports 300 or 600 dots per inch. 600 dots per inch is the default.
OBJECT-TYPE    
  INTEGER  

prtconsoledisplaybuffertext 1.3.6.1.4.1.11.2.3.9.4.2.2.16.5.1.2
The content of a line in the logical display buffer of the operator's console of the printer. When a write operation occurs, normally a critical message, to one of the LineText strings, the agent should make that line displayable if a physical display is present. Writing a zero length string clears the line. It is an implementation-specific matter as to whether the agent allows a line to be overwritten before it has been cleared. Printer generated strings shall be in the localization specified by prtConsoleLocalization. Management Application generated strings should be localized by the Management Application. Refer to Standard Printer MIB for more details. Additional information: Replaces PML STATUS-MSG-LINE1-PART1 and STATUS-MSG-LINE2-PART1 (read functionality). The proprietary objects BACKGROUND-STATUS-MSG-LINE1-PART1 and BACKGROUND-STATUS-MSG-LINE2-PART1 should be used to write messages to the control panel display. prtConsoleDisplayBufferText.1.[1..6] maps to logical lines 1-6 of the display. Most of the time the display will show a single one or two line message. This message can be retrieved by reading prtConsoleDisplayBufferText.1.1 and prtConsoleDisplayBufferText.1.2. In this case prtConsoleDisplayBufferText.1.[3..6] will be NULL. If prtConsoleDisplayBufferText.1.3 or prtConsoleDisplayBufferText.1.4 is not NULL, the display will be alternating. If prtConsoleDisplayBufferText.1.[5..6] are NULL, the display will alternate prtConsoleDisplayBufferText.1.[1..2] with prtConsoleDisplayBufferText.1.[3..4]. If prtConsoleDisplayBufferText.1.5 or prtConsoleDisplayBufferText.1.6 is not NULL, the display will show prtConsoleDisplayBufferText.1.[1..2] then prtConsoleDisplayBufferText.1.[3..4] then prtConsoleDisplayBufferText.1.[5..6]. The display will alternate between line pairs at three second intervals.
OBJECT-TYPE    
  STRING Size(0..255)  

prtconsoleontime 1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1.2
This object, in conjunction with prtConsoleOffTime, defines the current status of the light. If both prtConsoleOnTime and prtConsoleOffTime are non-zero, the lamp is blinking and the values presented define the on time and off time, respectively, in milliseconds. If prtConsoleOnTime is zero and prtConsoleOffTime is non-zero, the lamp is off. If prtConsoleOffTime is zero and prtConsoleOnTime is non-zero, the lamp is on. If both values are zero the status of the lamp is undefined. Refer to Standard Printer MIB for more details. Additional information: There are three control panel LED's: Ready (1), Data (2), and Attention (3). When an LED blinks, it is typically on for one half second and off for one half second. The value used for this object is 500 when the LED is on or blinking, otherwise it is zero.
OBJECT-TYPE    
  INTEGER  

prtconsoleofftime 1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1.3
This object, in conjunction with prtConsoleOnTime, defines the current status of the light. If both prtConsoleOnTime and prtConsoleOffTime are non-zero, the lamp is blinking and the values presented define the on time and off time, respectively, in milliseconds. If prtConsoleOnTime is zero and prtConsoleOffTime is non-zero, the lamp is off. If prtConsoleOffTime is zero and prtConsoleOnTime is non-zero, the lamp is on. If both values are zero the status of the lamp is undefined. Refer to Standard Printer MIB for more details. Additional information: There are three control panel LED's: Ready (1), Data (2), and Attention (3). When an LED blinks, it is typically on for one half second and off for one half second. The value used for this object is 500 when the LED is off or blinking, otherwise it is zero.
OBJECT-TYPE    
  INTEGER  

prtconsoledescription 1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1.5
The vendor description or label of this light in the localization specified by prtConsoleLocalization. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  STRING Size(0..255)  

prtalertseveritylevel 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.2
The level of severity of this alert table entry. The printer determines the severity level assigned to each entry into the table. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER ePother(1), ePcriticalBinaryChangeEvent(3), ePwarningUnaryChangeEvent(4), ePwarningBinaryChangeEvent(5)  

prtalerttraininglevel 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.3
See textual convention PrtAlertTrainingLevelTC Refer to Standard Printer MIB for more details. Additional information: The value of this object depends on the alert. Some examples: ePfieldService: Marker failure. ePtrained: Toner low. ePuntrained: Paper low/out. ePmanagement: Configuration change.
OBJECT-TYPE    
  INTEGER ePother(1), ePuntrained(3), ePtrained(4), ePfieldService(5), ePmanagement(6), ePnoInterventionRequired(7)  

prtalertgroup 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.4
The type of sub-unit within the printer model that this alert is related. Input, output, and markers are examples of printer model groups, i.e., examples of types of sub-units. Wherever possible, these enumerations match the sub-identifier that identifies the relevant table in the printmib. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER ePgeneralPrinter(5), ePcover(6), ePinput(8), ePoutput(9), ePmarker(10), ePmarkerSupplies(11), ePchannel(14)  

prtalertgroupindex 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.5
An index of the row within the principle table in the group identified by prtAlertGroup that represents the sub-unit of the printer that caused this alert. The combination of the prtAlertGroup and the prtAlertGroupIndex defines exactly which printer sub-unit caused the alert.; for example, Input #3, Output #2, and Marker #1. Every object in this MIB is indexed with hrDeviceIndex and optionally, another index variable. If this other index variable is present in the table that generated the alert, it will be used as the value for this object. Otherwise, this value shall be -1. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER  

prtalertlocation 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.6
The sub-unit location that is defined by the printer manufacturer to further refine the location of this alert within the designated sub-unit. The location is used in conjunction with the Group and GroupIndex values; for example, there is an alert in Input #2 at location number 7. The value (-2) indicates unknown Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER  

prtalertcode 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.7
See associated textual convention PrtAlertCodeTC Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER ePother(1), ePcoverOpened(3), ePjam(8), ePsubunitMissing(9), ePsubunitAlmostEmpty(12), ePsubunitEmpty(13), ePsubunitAlmostFull(14), ePsubunitFull(15), ePsubunitOffline(22), ePsubunitPowerSaver(23), ePsubunitMotorFailure(33), ePsubunitMemoryExhausted(34), ePmarkerFuserUnderTemperature(1001), ePmarkerFuserOverTemperature(1002), ePmarkerTonerEmpty(1101), ePmarkerTonerAlmostEmpty(1104)  

prtalertdescription 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.8
A description of this alert entry in the localization specified by prtGeneralCurrentLocalization. The description is provided by the printer to further elaborate on the enumerated alert or provide information in the case where the code is classified as `other' or `unknown'. The printer is required to return a description string but the string may be a null string. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  STRING Size(0..255)  

prtalerttime 1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.9
The value of sysUpTime at the time that this alert was generated. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER  

status-controller 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.23
Indicates if the hardware controller sub-system in a warning condition.
OBJECT-TYPE    
  STRING  

job-input-auto-continue-timeout 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.35
The number of seconds the device waits after a job related continuable error occurs before automatically continuing. An example job related continuable error is the job requesting a media size that is not available. After the timeout expires, the device will continue processing the job as if a continue event occurred, such as the front panel continue key being pressed. If the value is -1, the device does not automatically continue after a job related continuable error occurs. If the value is 0, the device immediately continues. If the value is greater than 0, the value represents the timeout value in seconds. Additional information: This object is used only for media requests (size and/or name). LaserJet 4050 Series supports any value in the range of -1 to 3600. Setting to a value outside of that range causes the printer to substitute a value (listed below) and to return status. The values are as follow: <-1 snaps to -1 >3600 snaps to 3600 (60 minutes) The action that occurs when this timeout expires is explained by JOB-INPUT-AUTO-CONTINUE-MODE. It is not the same as the CONTINUE object being set to eInitiateAction or the Select key being pressed on the control panel. See the CONTINUE object description for information on the actions that occur for those conditions. The data for this object is stored in NVRAM.
OBJECT-TYPE    
  INTEGER -1..3600  

job-input-auto-continue-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.36
Returns or sets the device behavior when the desired media is not currently available. cCancelJob - The device cancels the job. The device POS should explain what happens if this item is not the only item in the collection. cAutoMediaSizeOverride - The device is allowed to substitute a different size media. cAutoMediaNameOverride - The device is allowed to substitute a different media name. Additional information: If cCancelJob is set, the current print job will be canceled regardless of other item settings. At least one bit of the collection must be set; setting this object to zero will cause a status of to be returned. This object applies to all media requests, including Manual Feed Requests. This object describes the action that is performed when the JOB-INPUT-AUTO-CONTINUE-TIMEOUT expires. The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions. The data for this object is stored in NVRAM.
OBJECT-TYPE    
  STRING  

job-output-auto-continue-timeout 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.40
Returns or sets the time that the printer will wait after an output bin becomes full and the printer is trying to deliver a sheet of media to that output bin. When the timeout expires, the job is processed according to the OUTBINn-OVERRIDE-MODE. A value of -1 indicates that the printer will wait for a continue event. A non- negative value is the number of seconds to wait. Additional information: A value of zero means to continue immediately. The value of this object is stored in NVRAM, so it is maintained across a power cycle. The data for this object is stored in NVRAM.
OBJECT-TYPE    
  INTEGER -1..3600  

phd2-model 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2.1
Returns product information identifying PHD device 2. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the first paper handling device in the device chain.
OBJECT-TYPE    
  DisplayString  

phd2-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2.2
Returns information describing the manufacture of PHD 2. May include serial number and firmware revision. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the first paper handling device.
OBJECT-TYPE    
  DisplayString  

phd2-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2.3
Returns an indication of the type of option installed in PHD interface 2. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the device is an input device, an output device, or an unknown device which may be developed in the future.
OBJECT-TYPE    
  INTEGER eUnknown(2), eInputPHD(10), eOutputPHD(11), eBindingPHD(13)  

phd2-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2.4
Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least one (1) external paper handling device (EPHD) is attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD2-TYPE) for the first EPHD in the device chain.
OBJECT-TYPE    
  INTEGER  

phd3-model 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3.1
Returns product information identifying PHD device 3. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the second paper handling device in the device chain.
OBJECT-TYPE    
  DisplayString  

phd3-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3.2
Returns information describing the manufacture of PHD 3. May include serial number and firmware revision. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the second paper handling device.
OBJECT-TYPE    
  DisplayString  

phd3-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3.3
Returns an indication of the type of option installed in PHD interface 3. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the second device is an input device, an output device, or an unknown object which may be developed in the future.
OBJECT-TYPE    
  INTEGER eUnknown(2), eInputPHD(10), eOutputPHD(11), eBindingPHD(13)  

phd3-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3.4
Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least two (2) external paper handling devices (EPHD) are attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD3-TYPE) for the second EPHD in the device chain.
OBJECT-TYPE    
  INTEGER  

phd4-model 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4.1
Returns product information identifying PHD device 4. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the third paper handling device in the device chain.
OBJECT-TYPE    
  DisplayString  

phd4-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4.2
Returns information describing the manufacture of PHD 4. May include serial number and firmware revision. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the third paper handling device.
OBJECT-TYPE    
  DisplayString  

phd4-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4.3
Returns an indication of the type of option installed in PHD interface 4. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the third device is an input device, an output device, or an unknown device which may be developed in the future.
OBJECT-TYPE    
  INTEGER eUnknown(2), eInputPHD(10), eOutputPHD(11), eBindingPHD(13)  

phd4-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4.4
Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least three (3) external paper handling devices (EPHD) are attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD4-TYPE) for the third EPHD in the device chain.
OBJECT-TYPE    
  INTEGER  

phd5-model 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5.1
Returns product information identifying PHD device 3. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the fourth paper handling device in the device chain.
OBJECT-TYPE    
  DisplayString  

phd5-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5.2
Returns information describing the manufacture of PHD 5. May include serial number and firmware revision. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the fourth paper handling device.
OBJECT-TYPE    
  DisplayString  

phd5-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5.3
Returns an indication of the type of option installed in PHD interface 5. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the fourth device is an input device, an output device, or an unknown device which may be developed in the future.
OBJECT-TYPE    
  INTEGER eUnknown(2), eInputPHD(10), eOutputPHD(11), eBindingPHD(13)  

phd5-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5.4
Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least four (4) external paper handling devices (EPHD) are attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD5-TYPE) for the fourth EPHD in the device chain.
OBJECT-TYPE    
  INTEGER  

phd6-model 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6.1
Returns product information identifying PHD device 6. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the fifth paper handling device in the device chain.
OBJECT-TYPE    
  DisplayString  

phd6-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6.2
Returns information describing the manufacture of PHD 6. May include serial number and firmware revision. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the fifth paper handling device.
OBJECT-TYPE    
  DisplayString  

phd6-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6.3
Returns an indication of the type of option installed in PHD interface 6. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the fifth device is an input device, an output device, or an unknown device which may be developed in the future.
OBJECT-TYPE    
  INTEGER eUnknown(2), eInputPHD(10), eOutputPHD(11), eBindingPHD(13)  

phd6-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6.4
Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least five (5) external paper handling devices (EPHD) are attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD6-TYPE) for the fifth EPHD in the device chain.
OBJECT-TYPE    
  INTEGER  

override-media-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.2
Sets a string identifying the media name that is to be used in place of the currently requested media. The substitution will continue until another media is selected. If set to a named media that is not currently available the requested media is not overridden. Additional information: When a request is received to print on a size and type of media that is not currently available, this object contains the desired media name as set by the print job. This object should be set to a media name that is currently available in the printer. If a paper mount request is not pending, attempting to get or set this object will cause to be returned. Setting this object to a string other than one of the MEDIAn-NAME objects (MEDIA-NAMES-AVAILABLE is applied) will cause a status of to be returned.
OBJECT-TYPE    
  DisplayString  

total-engine-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.5
Total number of pages printed by the device. POS indicates if the total engine page count is kept in NVRAM, and the maximum supported value before the page count rolls over to zero. Additional information: In LaserJet 4V the total engine page count is kept in NVRAM however the NVRAM value is only updated every 10 pages. NOTE: The value returned by this OID will be incremented every page but if power is lost between NVRAM updates up to 9 pages of the page count may be lost. The page count counter will be reset to zero after 16,777,215 (2^24-1) pages.
OBJECT-TYPE    
  INTEGER  

status-destination-print-engine 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.8
Indicates if part of the print engine sub-system is not functional, but the non-functional component(s) are not currently required to print.
OBJECT-TYPE    
  STRING  

duplex-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.22
Total number of sheets of media that have been duplex printed. A sheet is counted if it travels through the duplex page path, regardless of whether or not marks are made on the page. The POS will indicate if the value is kept in NVRAM. Additional information: In LaserJet 4050 Series the count is kept in NVRAM however the NVRAM value is only updated every 10 sheets. NOTE: The value returned by this object will be incremented every sheet but if power is lost between NVRAM updates up to 9 sheets of the count may be lost. The counter will be reset to zero after 16,777,215 (2^24-1) pages.
OBJECT-TYPE    
  INTEGER  


custom-paper-dim-unit 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.7
The units of measure used to specify the width and height of the printer's custom paper. The unit of measure of eTenThousandthsOfInches is 0.0001 inches. Additional information: The only valid values for this object are eTenThousandthsOfInches (3), and eMicrometers (4). The data for this object is stored in NVRAM.
OBJECT-TYPE    
  INTEGER eTenThousandthsOfInches(3), eMicrometers(4)  

tray1-phd 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.12
Provides the number of the Paper Handling Device that contains this input tray. Additional information: The internal trays belong to device 0, which is the base engine. The envelope feeder (if supported) is considered to be device 1 and the external input devices can number between 2 and 6 depending on individual user configurations.
OBJECT-TYPE    
  INTEGER  

tray1-fuser-temperature 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.13
The fuser temperature to be used when printing media from Tray 1. The value zero is the default temperature. Values less than zero are progressively lower and values greater than zero are progressively higher. The range of values supported is device specific. Additional information: HP LaserJet 2100 Series supports 3 fuser temperatures. Zero (0) is the default temperature, one(1) is a higher temperature (for use on media like cardstock), negative one (-1) is a lower temperature (for use on media like transparencies). Setting to an unsupported value causes the printer to snap to the nearest supported value and to return status along with the actual value that was written. The snap values are as follows: <=-1 snaps to -1 >=1 snaps to 1
OBJECT-TYPE    
  INTEGER -1..1  

overflow-bin 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.1.4
Returns or sets the bin that will be used for additional sheets of media when the current bin is full and printing is allowed to continue. Additional information: The data for this object is stored in NVRAM.
OBJECT-TYPE    
  INTEGER  

outbin1-override-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1.9
Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.
OBJECT-TYPE    
  STRING  

outbin1-maximum-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1.1
Maximum capacity of the output bin, in sheets of 20 pound paper.
OBJECT-TYPE    
  INTEGER  

outbin2-override-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.2.9
Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: See OUTBIN1-OVERRIDE-MODE.
OBJECT-TYPE    
  STRING  

phd2-device-specific-command 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.2.2
This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the first device.
OBJECT-TYPE    
  STRING  

phd2-device-memory 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.2.4
This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the first paper handling device. Currently, the printer allocates 16 bytes for each device.
OBJECT-TYPE    
  STRING  

phd3-device-specific-command 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.3.2
This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the second device.
OBJECT-TYPE    
  STRING  

phd3-device-memory 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.3.4
This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the second paper handling device. Currently, the printer allocates 16 bytes for each device.
OBJECT-TYPE    
  STRING  

phd4-device-specific-command 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.4.2
This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the third device.
OBJECT-TYPE    
  STRING  

phd4-device-memory 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.4.4
This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the second paper handling device. Currently, the printer allocates 16 bytes for each device.
OBJECT-TYPE    
  STRING  

phd5-device-specific-command 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.5.2
This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the fourth device.
OBJECT-TYPE    
  STRING  

phd5-device-memory 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.5.4
This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the second paper handling device. Currently, the printer allocates 16 bytes for each device.
OBJECT-TYPE    
  STRING  

phd6-device-specific-command 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.6.2
This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the fifth device.
OBJECT-TYPE    
  STRING  

phd6-device-memory 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.6.4
This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the second paper handling device. Currently, the printer allocates 16 bytes for each device.
OBJECT-TYPE    
  STRING  

north-edge-offset 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1.2
Returns or sets the number of 300 dpi dots by which the image is shifted. Shift is relative to the leading edge of the medium as the medium flows through the marking engine with the side to be imaged facing the observer. The leading edge is the North edge and the other edges are defined by the normal compass layout of directions with the compass facing the observer. The adjustment is for all pages printed. A positive value moves the image away from the leading edge of the medium. A negative value moves the image closer to the leading edge of the medium. The value 0 will return the image to its factory default position. Additional information: The value of this object is stored in NVRAM.
OBJECT-TYPE    
  INTEGER  

media1-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.1
Media 1 name. Additional information: The symbol set for this string is Roman-8.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media1-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.2
Length restricted version of the media name 1. The length restriction is required to allow the media name to be displayed on the device's control panel. The device POS must state the maximum number of characters allowed. If the device also has a limitation on what characters in a character set can be used (e.g. only uppercase characters allowed), the POS should also state character restrictions. Additional information: The maximum supported string length is 9 characters. If the user entered string is too long, the device will store the first 9 characters and will return the status. The characters must be in the range 20H to 7FH except 5C cannot be used. The default symbol set is Roman-8 for English; additional legal symbol sets are ISOLatin5, ISOLatin2 and Windows31J. Setting this object with characters outside of the range or of an illegal symbol set will cause an error status of to be returned.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media1-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.3
Number of sheets of media 1 that have been printed. The device POS should state whether this value is lost across a power cycle or kept in NVRAM. Additional information: For LaserJet 4050 Series this page count is saved in NVRAM after every 10 pages. The maximum value is 4,294,967,295 which will never be reached in normal operation. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by one. The data for this object is stored in NVRAM.
OBJECT-TYPE    
  INTEGER  

media1-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: The engine processing characteristics that are to be applied to this media type. Currently, 'engine processing characteristics' denotes changes to fusing temperature and/or transfer roller voltage. The data for this object is stored in NVRAM.
OBJECT-TYPE    
  INTEGER  

media2-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.1
Media 2 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media2-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.2
Length restricted version of the media name 2. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media2-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.3
Number of sheets of media 2 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media2-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media3-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.1
Media 3 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media3-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.2
Length restricted version of the media name 3. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media3-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.3
Number of sheets of media 3 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media3-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media4-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.1
Media 4 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media4-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.2
Length restricted version of the media name 4. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media4-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.3
Number of sheets of media 4 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media5-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.1
Media 5 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media5-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.2
Length restricted version of the media name 5. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media5-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.3
Number of sheets of media 5 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media5-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media6-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.1
Media 6 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media6-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.2
Length restricted version of the media name 6. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media6-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.3
Number of sheets of media 6 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media7-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.1
Media 7 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media7-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.2
Length restricted version of the media name 7. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media7-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.3
Number of sheets of media 7 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media7-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media8-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.1
Media 8 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media8-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.2
Length restricted version of the media name 8. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media8-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.3
Number of sheets of media 8 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media8-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media9-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.1
Media 9 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media9-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.2
Length restricted version of the media name 9. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media9-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.3
Number of sheets of media 9 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media9-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media10-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.1
Media 10 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media10-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.2
Length restricted version of the media name 10. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media10-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.3
Number of sheets of media 10 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media11-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.1
Media 11 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media11-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.2
Length restricted version of the media name 11. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media11-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.3
Number of sheets of media 11 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media12-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.1
Media 12 name. Additional information: See MEDIA1-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media12-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.2
Length restricted version of the media name 12. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media12-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.3
Number of sheets of media 12 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media12-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media13-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.1
Media 13 name. Additional information: The maximum supported string length is 24 bytes. If the user entered string is too long, the device will store the first 24 bytes and return the status. See CAUTION statement under Product Specific Use.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media13-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.2
Length restricted version of the media name 13. See MEDIA1-SHORT-NAME for details. Additional information: The maximum supported string length is 9 characters. If the user entered string is too long, the device will store the first 9 characters and will return the status. The characters must be in the range 20H to 7FH except 5C cannot be used. The default symbol set is Roman-8 for English; additional legal symbol sets are ISOLatin5, ISOLatin2 and Windows31J. Setting this object with characters outside of the range or of an illegal symbol set will cause an error status of to be returned.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media13-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.3
Number of sheets of media 13 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media13-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media14-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.1
Media 14 name. Additional information: See MEDIA13-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media14-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.2
Length restricted version of the media name 14. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA13-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media14-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.3
Number of sheets of media 14 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA13-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media14-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media15-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.1
Media 15 name. Additional information: See MEDIA13-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media15-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.2
Length restricted version of the media name 15. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA13-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media15-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.3
Number of sheets of media 15 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA13-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media15-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media16-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.1
Media 16 name. Additional information: See MEDIA13-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media16-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.2
Length restricted version of the media name 16. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA13-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media16-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.3
Number of sheets of media 16 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA13-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media16-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

media17-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.1
Media 17 name. Additional information: See MEDIA13-NAME.
OBJECT-TYPE    
  DisplayString Size(1..24)  

media17-short-name 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.2
Length restricted version of the media name 17. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA13-SHORT-NAME.
OBJECT-TYPE    
  DisplayString Size(1..9)  

media17-page-count 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.3
Number of sheets of media 17 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA13-PAGE-COUNT.
OBJECT-TYPE    
  INTEGER  

media17-engine-media-mode 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.4
The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
OBJECT-TYPE    
  INTEGER  

prtinputdefaultindex 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.6
The value of prtInputIndex corresponding to the default input sub-unit: that is, this object selects the default source of input media. This value shall be -1 if there is no default input subunit specified for the printer as a whole. In this case, the actual default input subunit may be specified by means outside the scope of this MIB, such as by each interpreter in a printer with multiple interpreters. Refer to Standard Printer MIB for more details. Additional information: The default input tray is determined by the printer based on DEFAULT-MEDIA-SIZE and DEFAULT-MEDIA-NAME, and whether or not optional trays are installed. If Tray 1 is set in FIRST mode then the size of paper loaded in Tray 1 is assumed to be the requested size. In this case, the printer will pick from Tray 1 without regard to the requested size unless the print job's paper size, paper type and tray designations exactly match the configuration of another tray; in that case, the requested tray will be picked.
OBJECT-TYPE    
  INTEGER  

prtmarkerdefaultindex 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.8
The value of prtMarkerIndex corresponding to the default marker sub-unit; that is, this object selects the default marker. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4050 Series only has one marker subunit.
OBJECT-TYPE    
  INTEGER 1..65535  

prtmediapathdefaultindex 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.9
The value of prtMediaPathIndex corresponding to the default media path; that is, the selection of the default media path. Refer to Standard Printer MIB for more details. Additional information: If the duplex unit is not installed, the only valid value for this object is 1; with duplex unit installed, 1-3 values are valid. 1 is simplex, 2 is LongEdgeBindingDuplex, and 3 is ShortEdgeBindingDuplex. If the printer is not idle, the new value of this object may not take effect until a job boundary is reached. If a get is done on this object before the job boundary is reached, the value last set will be returned.
OBJECT-TYPE    
  INTEGER 1..3  

prtcoverdescription 1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1.2
The manufacturer provided cover sub-mechanism name in the localization specified by prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  STRING Size(0..255)  

prtcoverstatus 1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1.3
The status of this cover sub-unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML NOT-READY-DOOR-OPEN.
OBJECT-TYPE    
  INTEGER ePdoorOpen(3), ePdoorClosed(4)  

prtmarkermarktech 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.2
The type of marking technology used for this marking sub-unit. Refer to Standard Printer MIB for more details. Additional information: ePelectrophotographicLaser is the only value that applies for the LaserJet 4050 Series products, and this is the value that will always be returned for this object.
OBJECT-TYPE    
  INTEGER ePelectrophotographicLaser(4)  

prtmarkercounterunit 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.3
The unit that will be used by the printer when reporting counter values for this marking sub-unit. The time units of measure are provided for a device like a strip recorder that does not or cannot track the physical dimensions of the media and does not use characters, lines or sheets. Refer to Standard Printer MIB for more details. Additional information: Since LaserJet 4050 Series keeps track of pages printed, the counter unit will be defined as ePimpressions which would be like saying pages printed.
OBJECT-TYPE    
  INTEGER ePimpressions(7)  

prtmarkerlifecount 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.4
The count of the number of units of measure counted during the life of printer using units of measure as specified by prtMarkerCounterUnit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML TOTAL-ENGINE-PAGE-COUNT. The total engine page count is kept in NVRAM however the NVRAM value is only updated every 10 impressions. NOTE: The value returned by this OID will be incremented every page but if power is lost between NVRAM updates, up to 9 impressions of the page count may be lost. The counter will be reset to zero after 999999 pages. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by two.
OBJECT-TYPE    
  INTEGER  

prtmarkerpoweroncount 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.5
The count of the number of units of measure counted since the equipment was most recently powered on using units of measure as specified by prtMarkerCounterUnit. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER  

prtmarkerprocesscolorants 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.6
The number of process colors supported by this marker. A process color of 1 implies monochrome. The value of this object and prtMarkerSpotColorants cannot both be 0. The value of prtMarkerProcessColorants must be 0 or greater. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER 0..65535  

prtmarkerspotcolorants 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.7
The number of spot colors supported by this marker. The value of this object and prtMarkerProcessColorants cannot both be 0. Must be 0 or greater. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER 0..65535  

prtmarkeraddressabilityunit 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.8
The unit of measure of distances, as applied to the marker's resolution. Refer to Standard Printer MIB for more details. Additional information: This will always be ePtenThousandthsOfInches, no matter what COLD-RESET-MEDIA-SIZE is because we are talking about resolution and toner addressability, which is always dpi.
OBJECT-TYPE    
  INTEGER ePtenThousandthsOfInches(3)  

prtmarkernorthmargin 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.11
The margin, in units identified by prtMarkerAddressabilityUnit, from the leading edge of the medium as the medium flows through the marking engine with the side to be imaged facing the observer. The leading edge is the North edge and the other edges are defined by the normal compass layout of directions with the compass facing the observer. Printing within the area bounded by all four margins is guaranteed for all interpreters. The value (-2) means unknown. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER  

prtmarkersouthmargin 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.12
The margin from the South edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by all four margins is guaranteed for all interpreters. The value (-2) means unknown. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER  

prtmarkerwestmargin 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.13
The margin from the West edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by all four margins is guaranteed for all interpreters. The value (-2) means unknown. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER  

prtmarkereastmargin 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.14
The margin from the East edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by all four margins is guaranteed for all interpreters. The value (-2) means unknown. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER  

prtmarkerstatus 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.15
The current status of this marker sub-unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML NOT-READY-DESTINATION-PRINT-ENGINE and STATUS-DESTINATION-PRINT-ENGINE. 51 = No toner cart. 49 = Low toner and toner low = stop in config menu 14 = Low toner and toner low = continue in config menu and paper is moving. 08 = Low toner and toner low = continue in config menu and no paper is moving. 00 = OK. The default value assumes no malfunctions.
OBJECT-TYPE    
  INTEGER  

prtmarkersuppliesmarkerindex 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.2
The value of prtMarkerIndex corresponding to the marking sub-unit with which this marker supply sub-unit is associated. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4050 Series has just one marker supply, the toner cartridge, so this value is always 1.
OBJECT-TYPE    
  INTEGER 0..65535  

prtmarkersuppliescolorantindex 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.3
The value of prtMarkerColorantIndex corresponding to the colorant with which this marker supply sub-unit is associated. This value shall be 0 if there is no colorant table. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER 0..65535  

prtmarkersuppliesclass 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.4
Indicates whether this supply entity represents a supply that is consumed or a receptacle that is filled. Refer to Standard Printer MIB for more details. Additional information: ePsupplyThatIsConsumed is the only value that applies for the LaserJet 4050 Series products, and this is the value that will always be returned for this object.
OBJECT-TYPE    
  INTEGER ePsupplyThatIsConsumed(3)  

prtmarkersuppliestype 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.5
The type of this supply. Refer to Standard Printer MIB for more details. Additional information: ePtoner is the only value that applies for the LaserJet 4050 Series products, and this is the value that will always be returned for this object.
OBJECT-TYPE    
  INTEGER ePtoner(3)  

prtmarkersuppliessupplyunit 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.7
Unit of measure of this marker supply container/receptacle. Refer to Standard Printer MIB for more details. Additional information: ePtenthsOfGrams will always be returned for this object.
OBJECT-TYPE    
  INTEGER ePtenthsOfGrams(13)  

prtmarkercolorantmarkerindex 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1.2
The value of prtMarkerIndex corresponding to the marker sub-unit with which this colorant entry is associated. Additional information: LaserJet 4500 only has one marker. Therefore, the value of these objects is always 1.
OBJECT-TYPE    
  INTEGER 0..65535  

prtmarkercolorantrole 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1.3
The role played by this colorant. Additional information: All LaserJet 4500 colorants are process colorants.
OBJECT-TYPE    
  INTEGER ePother(1), ePprocess(3), ePspot(4)  

prtmarkercolorantvalue 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1.4
The name of the color of this colorant using standardized string names from ISO 10175 (DPA) and ISO 10180 (SPDL) which are: other unknown white red green blue cyan magenta yellow black Implementors may add additional string values. The naming conventions in ISO 9070 are recommended in order to avoid potential name clashes
OBJECT-TYPE    
  STRING Size(0..255)  

prtmarkercoloranttonality 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1.5
The distinct levels of tonality realizable by a marking sub-unit when using this colorant. This value does not include the number of levels of tonal difference that an interpreter can obtain by techniques such as half toning. This value must be at least 2. Additional information: LaserJet 4500 supports eight bits per pixel.
OBJECT-TYPE    
  INTEGER  

prtmediapathmaxspeedprintunit 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.2
The unit of measure used in specifying the speed of all media paths in the printer. Refer to Standard Printer MIB for more details. Additional information: ePimpressionsPerHour is the value that will always be returned for this object. (Print Speed is measured in pages-per-minute (impressions per minute), so ePimpressionsPerHour is a natural extension).
OBJECT-TYPE    
  INTEGER ePimpressionsPerHour(7)  

prtmediapathmediasizeunit 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.3
The units of measure of media size for use in calculating and relaying dimensional values for all media paths in the printer. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  INTEGER ePtenThousandthsOfInches(3), ePmicrometers(4)  

prtmediapathtype 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.9
The type of the media path for this media path. Refer to Standard Printer MIB for more details. Additional information: Replaces PML DUPLEX-INSTALLED.
OBJECT-TYPE    
  INTEGER ePlongEdgeBindingDuplex(3), ePshortEdgeBindingDuplex(4), ePsimplex(5)  

prtmediapathdescription 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.10
The manufacturer-provided description of this media path in the localization specified by prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details.
OBJECT-TYPE    
  STRING Size(0..255)  

prtmediapathstatus 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.11
The current status of this media path. Refer to Standard Printer MIB for more details. Additional information: The default values assume the printer is idle.
OBJECT-TYPE    
  INTEGER  

collated-originals-support 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.42
Indicates that the printer can create multiple, collated 'originals' of a job and shows the level of support for this capability. cCollatedOriginals - The printer can create multiple collated originals, or 'mopies'. This is the base functionality required by the other collection items. cProofAndHold - The printer saves a copy of the job while printing the first mopy. Later, this held job can be released and the rest of the mopies will print. cSecurityPrint - The printer spools the job and holds the job until the user releases the job by entering a password at the printer's control panel. cAutoHighlight - The printer prints the job a number of times with a mail distribution list prepended to each job. A different mailing address is highlighted on each mopy. cCollatedAtSpeed - The printer can create multiple collated copies where all copies after the original are printed at engine speed. Additional information: Indicates that the printer can create multiple, collated originals of a job and shows the level of support for this capability. cCollatedOriginals - The printer can create multiple collated originals, or mopies. This is the base functionality required by the other collection items. None of them are supported by Jonah. Without disk, this object will not exist. This will be set at boot-up initialization. If the disk fails, in any way, then the disk error functionality will handle the situation. The value of this object will be: !cCollatedOriginals - Only FLASH installed cCollatedOriginals - IDE is installed combined with/without FLASH cCollatedOriginals - RAMDISK is On combined with/without FLASH
OBJECT-TYPE    
  STRING  

file-system-memory 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.1
The amount of memory, in bytes, used by the file system to buffer file data. Additional information: Reports the amount of memory, in bytes, reserved for use by the file system. Returns status if attempting to access this object and there is no storage device is installed. The values remain constant across reboots. Possible Values: FILE-SYSTEM-MAX-OPEN-FILES 32 512 EIO DISK 69916 198556 EIO DISK + 1 2MB Flash 88940 217580 1 2MB Flash 33052 161692
OBJECT-TYPE    
  INTEGER  

file-system-test-return-code 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.3
This test object that will not be supported in any released product. Setting this object allows the next file system call return code to be specified or to simulate uninitialized or unistalled volumes. The POS will specify the binary format. Additional information: A three byte binary value. The first byte indicates what function is being effected by this set. value | function ------+------------------ 1 | PersFSCtl 2 | PersFSDirClose 3 | PersFSDirCreate 4 | PersFSDirDelete 5 | PersFSDirOpen 6 | PersFSDirRead 7 | PersFSDirReadStd 8 | PersFSDirRewind 9 | PersFSDirSeek 10 | PersFSDirTell 11 | PersFSFileClose 12 | PersFSFileDelete 13 | PersFSFileMove 14 | PersFSFileOpen 15 | PersFSFileRead 16 | PersFSFileSeek 17 | PersFSFileStatus 18 | PersFSFileWrite 19 | PersFSFlush 20 | PersFSVolChk 21 | PersFSVolFix 22 | PersFSVolInit 23 | PersFSVolStatus The return value of the function being effected will return the value -1 to indicate an error occurred. The second byte is the value returned by the next call to PersFSErrNo() (after the call being effected is called). Refer to the 'Copernicus Personality Interface Volume 2 Disk File System' documentation for a list of values returned by PersFSErrNo(). The third byte indicates which call to the specified file system routine will fail. A value of one means the first call will fail. A value of two means the second call will fail, and so on. Writing this object causes any previous write to this object to be invalidated. Note: The error triggering mechanism is actually implemented at the message interface to the file system rather than at the PersFSxxx() function call interface. This is easier to do, and it is better for NFS because NFS uses the message interface rather than the PersFSxxx() functions. Fortunately there is a one-to-one mapping between messages and PersFSxxx() functions so everything works out nicely. The printer will uninitialize the mass storage device if the first byte is one of the values listed below. value | meaning ------+------------------ 101 | Effects the printer state 102 | Effects the data on the device The Moby printer supports 3 volumes zero, so the second byte must be 0 - 2. The third byte has no meaning and must be zero.
OBJECT-TYPE    
  STRING  

file-system-statistic-read-open 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.1
The number of times the file system has received requests to open a file for reading. Opening a file for both reading and writing will cause this value to change. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed. This value is increamented when a file is opened.
OBJECT-TYPE    
  INTEGER  

file-system-statistic-write-open 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.2
The number of times the file system has received requests to open a file for writing. Opening a file for both reading and writing will cause this value to change. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed. This value is increamented when a file is opened.
OBJECT-TYPE    
  INTEGER  

file-system-statistic-successful 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.3
A counter indicating the number of file system requests that completed successfully. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
OBJECT-TYPE    
  INTEGER  

file-system-statistic-unsuccessful 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.4
A counter indicating the number of file system requests that completed unsuccessfully. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
OBJECT-TYPE    
  INTEGER  

file-system-statistic-current-memory-usage 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.5
A value indicating the number of bytes of RAM currently used by the file system firmware. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed. This will veri depending on the number and size of Mass Storage devices installed.
OBJECT-TYPE    
  INTEGER  

file-system-statistic-max-memory-usage 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.6
A value indicating the maximum number of bytes of RAM used by the file system firmware. The POS should state if the value is reset to zero after a power cycle. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
OBJECT-TYPE    
  INTEGER  

file-system1-initialized 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.1.1
Returns eTrue if a file system has been written to the mass storage device(s) which will hold file data contained in this file system. Returns eFalse otherwise. Each POS needs to specify the relationship between file systems and the physical storage devices that can hold the data contained in those file systems. Additional information: This objects is only supported if a disk is installed. Returns status if attempting to perform a Get on this OID with no disk installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no disk installed.
OBJECT-TYPE    
  INTEGER eFalse(1), eTrue(2)  

file-system1-capacity 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.1.2
Returns the total size, in bytes, of the mass storage space configured to hold the file data (and file system information) assoicated with files stored in this file system. This refers to hardware capacity, independent of any space consumed by the file system overhead or user files. Additional information: This objects is only supported if a disk is installed. Returns status if attempting to perform a Get on this OID with no disk installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no disk installed.
OBJECT-TYPE    
  INTEGER  

file-system1-free-space 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.1.3
Returns the total amount, in bytes, of unused storage space currently available to this file system. Additional information: This objects is only supported if a disk is installed. Returns status if attempting to perform a Get on this OID with no disk installed. Returns status if attempting to perform a Set, EnableTrap, or DisableTrap on this OID with no disk installed.
OBJECT-TYPE    
  INTEGER  

file-system1-write-protect 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.1.4
Supports write-protecting the file system. Setting FILE-SYSTEM-WRITE-PROTECT to eEnabled blocks any modification of the contents of the file system. Setting FILE-SYSTEM-WRITE-PROTECT to eDisabled allows modification of the contents of the file system. Additional information: This objects is only supported if a disk is installed. Returns status if attempting to perform a Get, or Set on this OID with no disk installed. Returns status if attempting to perform an EnableTrap, or DisableTrap on this OID with no disk installed.
OBJECT-TYPE    
  INTEGER eDisabled(1), eEnabled(2)  

file-system2-initialize-volume 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.2.6
Setting this object to eInitializing causes file system 2 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 mass storage device, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM2-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 1st device.
OBJECT-TYPE    
  INTEGER eInitializing(2)  

file-system3-initialize-volume 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.3.6
Setting this object to eInitializing causes file system 3 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 mass storage device, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM3-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 2nd device.
OBJECT-TYPE    
  INTEGER eInitializing(2)  

file-system4-initialize-volume 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.4.6
Setting this object to eInitializing causes file system 4 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 mass storage devices, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM4-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 3rd device.
OBJECT-TYPE    
  INTEGER eInitializing(2)  

mass-storage-resource-change-counter 1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3.1
A counter which changes when a mass storage based resource has been added or deleted. Additional information: The value of this counter changes each time the MASS-STORAGE-RESOURCE-CHANGED object is set to eTrue. The value also changes when the mass storage device is initialized. However, the value does not change when a mass storage device is removed and a different mass storage device is installed. Initializing all volumes sets this object back to the factory default value. A reboot sets this object back to the factory devalut value. Returns status if attempting to access this object and there is no storage device is installed.
OBJECT-TYPE    
  INTEGER  

mass-storage-resource-changed 1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3.2
Setting to eTrue causes MASS-STORAGE-RESOURCE-CHANGE- COUNTER to be incremented. Additional information: Returns status if attempting to access this object and there is no storage device is installed.
OBJECT-TYPE    
  INTEGER eTrue(2)  

hrstoragesize 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.5
The size of the storage represented by this entry, in units of hrStorageAllocationUnits. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer): Total formatter RAM. Additional information (mass storage): Applications can determine the size of the installed mass storage device by getting the hrStorageAllocationUnits object and this object. The size of the mass storage device is these two returned values multiplied together. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER 0..2147483647  

hrdevicedescr 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.3
A textual description of this device, including the device's manufacturer and revision, and optionally, its serial number. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : The serial number is not returned with this object. This object is not localized. Additional information (mass storage) : Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  STRING Size(0..64)  

hrdeviceid 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.4
The product ID for this device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : The complete OID reported by this object is: .1.3.6.1.4.1.11.2.3.9.1.2.12 Additional information (mass storage) : Constant. Since we don't know all the possible registered OIDs for each mass storage device model that could be installed in this printer, this object always returns the unknown product ID. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

hrdeviceerrors 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.6
The number of errors detected on this device. It should be noted that as this object has a SYNTAX of Counter, that it does not have a defined initial value. However, it is recommended that this object be initialized to zero. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (mass storage): Total number of read and write errors that have occurred since the printer was turned on. Returns status if attempting to perform a Get on this OID with no mass storage device installed. Returns 0 if the mass storage device is uninitialized.
OBJECT-TYPE    
  INTEGER  

hrdiskstorageaccess 1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1.1
An indication if this long-term storage device is readable and writable or only readable. This should reflect the media type, any write-protect mechanism, and any device configuration that affects the entire device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: This object can be set to write protect the mass storage device, even though the host resources MIB documents the object as read-only. Applications wanting to know if the mass storage device is writable should get this object. Applications wanting to change the read/write access of the mass storage device should set this object. If this object is set to write-protect while a file is being written to the mass storage device, the write-protect takes effect immediately and the new file doesn't appear in the file system. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER eHreadWrite(1), eHreadOnly(2)  

hrdiskstoragemedia 1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1.2
An indication of the type of media used in this long-term storage device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Applications can determine if the installed mass storage device is a disk or is flash by getting this value. Possible Values: EIO DISK returns eHhardDisk Ram Disk returns eHramDisk Flash Disk returns eHother Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER eHother(1), eHhardDisk(3), eHramDisk(8)  

hrdiskstorageremoveble 1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1.3
Denotes whether or not the disk media may be removed from the drive. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER eHfalse(2)  

hrdiskstoragecapacity 1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1.4
The total size for this long-term storage device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The capacity is in Kbytes. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER  

hrpartitionindex 1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.1
A unique value for each partition on this long- term storage device. The value for each long-term storage device must remain constant at least from one re-initialization of the agent to the next re- initialization. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The first and second index indicates the hrDeviceIndex for this mass storage device. The value of this object is the same as the second index. The printer only supports one partition per mass storage device. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER 1..2147483647  

hrpartitionlabel 1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.2
A textual description of this partition. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The MS-DOS volume label. The volume label is writable. Returns status if attempting to perform a Get on this OID with no mass storage device installed. This object is settable and returns the empty string if the mass storage device has not been initialized. NOTE the RamDisk will lose this value after a PowerCycle.
OBJECT-TYPE    
  STRING Size(0..11)  

hrpartitionid 1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.3
A descriptor which uniquely represents this partition to the responsible operating system. On some systems, this might take on a binary representation. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The value returned is the ASCII string version of the hrDeviceIndex for this mass storage device. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  STRING  

hrpartitionsize 1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.4
The size of this partition. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The capacity is in Kbytes. Returns the same value as hrDiskStorageCapacity. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER  

hrpartitionfsindex 1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.5
The index of the file system mounted on this partition. If no file system is mounted on this partition, then this value shall be zero. Note that multiple partitions may point to one file system, denoting that that file system resides on those partitions. Multiple file systems may not reside on one partition. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Indicates if the mass storage device has been initialized. Applications determine if the storage device has been initialized by getting this object. Returns zero if the mass storage device is not initialized, otherwise the value matches the hrDeviceIndex value for this mass storage device. The value indicates the hrFileSystemTable index for the file system stored on this partition. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OBJECT-TYPE    
  INTEGER 0..2147483647  

hrfsindex 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.1
A unique value for each file system local to this host. The value for each file system must remain constant at least from one re-initialization of the agent to the next re-initialization. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The index is assigned by the person controlling the printer object definition. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  INTEGER 1..2147483647  

hrfsmountpoint 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.2
The path name of the root of this file system. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  STRING  

hrfsremotemountpoint 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.3
A description of the name and/or address of the server that this file system is mounted from. This may also include parameters such as the mount point on the remote file system. If this is not a remote file system, this string should have a length of zero. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. This printer does not support remote file system mounting. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  STRING  

hrfstype 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.4
The value of this object identifies the type of this file system. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

hrfsaccess 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.5
An indication if this file system is logically configured by the operating system to be readable and writable or only readable. This does not represent any local access-control policy, except one that is applied to the file system as a whole. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Returns the same value as hrDiskStorageAccess. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  INTEGER eHreadWrite(1), eHreadOnly(2)  

hrfsbootable 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.6
A flag indicating whether this file system is bootable. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  INTEGER eHfalse(2)  

hrfsstorageindex 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.7
The index of the hrStorageEntry that represents information about this file system. If there is no such information available, then this value shall be zero. The relevant storage entry will be useful in tracking the percent usage of this file system and diagnosing errors that may occur when it runs out of space. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The value indicates the hrStorageTable index for this mass storage device. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  INTEGER 0..2147483647  

hrfslastfullbackupdate 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.8
The last date at which this complete file system was copied to another storage device for backup. This information is useful for ensuring that backups are being performed regularly. If this information is not known, then this variable shall have the value corresponding to January 1, year 0000, 00:00:00.0, which is encoded as (hex)'00 00 01 01 00 00 00 00'. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The default value is the value defined to represent an unknown time of January 1, year 0000, 00:00:00.0. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  STRING  

hrfslastpartialbackupdate 1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.9
The last date at which a portion of this file system was copied to another storage device for backup. This information is useful for ensuring that backups are being performed regularly. If this information is not known, then this variable shall have the value corresponding to January 1, year 0000, 00:00:00.0, which is encoded as (hex)'00 00 01 01 00 00 00 00'. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The default value is the value defined to represent an unknown time of January 1, year 0000, 00:00:00.0. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OBJECT-TYPE    
  STRING  

mio1-model-name 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.2
Returns product information identifying the I/O card. Example: XXXX
OBJECT-TYPE    
  DisplayString  

mio1-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.3
Returns information describing the manufacture of the I/O card installed in MIO/EIO slot 1. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.
OBJECT-TYPE    
  DisplayString  

mio1-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.4
Returns an indication of the type of option installed in MIO/EIO slot 1. See SIMM1-TYPE for an explanation of the enumerations.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eDiskDrive(8), eIOCard(12)  

mio2-model-name 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.2
Returns product information identifying the I/O card. Example: XXXX
OBJECT-TYPE    
  DisplayString  

mio2-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.3
Returns information describing the manufacture of the I/O card installed in MIO/EIO slot 2. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.
OBJECT-TYPE    
  DisplayString  

mio2-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.4
Returns an indication of the type of option installed in MIO/EIO slot 2. See SIMM1-TYPE for an explanation of the enumerations.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eDiskDrive(8), eIOCard(12)  

mio3-model-name 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.3.2
Returns product information identifying the I/O card. Example: XXXX
OBJECT-TYPE    
  DisplayString  

mio3-manufacturing-info 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.3.3
Returns information describing the manufacture of the I/O card installed in MIO/EIO interface 3. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.
OBJECT-TYPE    
  DisplayString  

mio3-type 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.3.4
Returns an indication of the type of option installed in MIO/EIO interface 3. See SIMM1-TYPE for an explanation of the enumerations.
OBJECT-TYPE    
  INTEGER eEmpty(1), eUnknown(2), eDiskDrive(8), eIOCard(12)  

job-info-change-id 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.3
Returns the current value of an object in the job-info sub-tree whose value has changed. Define the object identifier for the object whose value has changed as job-info.required-field.optional-field.job-id. job-info represents the OID prefix of all objects in the job-info sub-tree. Required-field represents the OID field value that follows the job-info prefix. Since some objects in the job-info sub-tree have two OID fields between the job-info prefix and the job-id, the optional-field represents the OID field between the required-field and the job-id field, if present. Using this definition, the format for the JOB-INFO-CHANGE-ID binary value can be described as follows: Bytes 0-3 : required-field Bytes 4-7 : optional-field, or all zeros if there is no optional field Bytes 8-11: Job ID. Bytes 12-n : The value of the object job-info. required-field.optional-field.job-id. All multi-byte values stored in Motorola (big-endian) format, where the most significant byte occurs first. Additional information: LaserJet 4050 Series will use this object to report changes to the job-info-pages-printed and job-info-state objects. The required-field (bytes 0 through 3) will designate whether the change to be reported involves the pages printed (13) or job state (15). The optional-field (bytes 4 through 7) will always be zeroes. The value-field (bytes 12 through 15) will contain the new value for pages printed or job state cast to a 32-bit integer.
OBJECT-TYPE    
  STRING Size(16)  

hold-job-timeout 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.10
The time, in minutes, that the printer will wait before automatically deleting a held job. This allows the printer to automatically clean up jobs that have been forgotten (held but never released). Additional information: This only applies to temporary held jobs, i.e., HOLD=ON or PROOF. This is a global timer that only affects the jobs that are sent after it is set. A value of 0 means never delete the jobs. Setting it to an unsupported value causes the printer to substitute a value (listed below) and to return status. LaserJet 4050 Series supports values of 0, 60, 240, 1440, and 10080 The values are as follows: <=0 snap to 0 (disabled) >=1 and <=150 snap to 60 (60 minutes) >=151 and <=840 snap to 240 (4 hours) >=841 and <=2880 snap to 1440 (1 day) >=2881 snap to 10080 (1 week)
OBJECT-TYPE    
  INTEGER  

current-job-parsing-id 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1.1
Contains the printer assigned job identification for the job currently being processed by the processing PDL sub- system. The job ID is a monotonically increasing number. The job ID may be reset to zero at power-up and may roll over to zero after reaching some maximum value. Additional information: A value of -1 is returned when the printer is not parsing a job. When data for a new job is detected, this object is updated (the job may or may not turn out to be a Null Job); however, the trap does not occur until the printer determines that it is not a Null Job. (A job is considered to be a 'null job' if it has no name or job attribute, causes no pages to be printed, and consumes MIN_JOB_SIZE (9) or fewer bytes.) A trapped value will differ from the previous value by one or more. Some job-info- objects are created when the first data bytes are received. If the printer determines that the job is a Null Job, the job-info- objects related to the Null Job are deleted. LaserJet 4050 Series retains the job-info- objects for the MAX_JOBS_IN_LIST (12) most recent jobs that are not Null Jobs. The first job received after power-up will have job ID 1, and the job ID will increment to 32767 before rolling to zero. To distinguish whether a power cycle or a rollover causes a reduction in the job ID value, the object prtGeneralConfigChanges can be watched and if it increments at the same time as the drop is observed in the value of CURRENT-JOB-PARSING-ID, then a power cycle is the most likely cause.
OBJECT-TYPE    
  INTEGER -1..32767  

job-info-name1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.1
Contains the first part of this print job's name. The last OID field for this dynamic object contains the job ID. Additional information: The job name is the string specified by the NAME= parameter of the @PJL JOB command which allows a maximum of 80 characters. The first 40 characters are in this object and the second 40 are in job-info-name2. The symbol set is Roman-8. When jobs are nested, the value assigned to this object is the name provided by the most recent @PJL JOB NAME= command. If no name is provided, a null string is returned.
OBJECT-TYPE    
  DisplayString  

job-info-name2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.2
Contains the second part of this print job's name. The last OID field for this dynamic object contains the job ID. Additional information: See job-info-name1.
OBJECT-TYPE    
  DisplayString  

job-info-stage 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.10
Indicates what printer sub-systems are currently processing this print job. The last OID field for this dynamic object contains the job ID. cSourceSubsystem - some of the job is in the printer I/O subsystem. cProcessingSubsystem - some of the job is in the printer imaging processing subsystem. cDestinationSubsystem - some of the job is being printed. Additional information: For LaserJet 4050 Series, cSourceSubsystem and cProcessingSubsystem will always be set and cleared together. They are set when the beginning of the job is detected, and they are cleared when the end of the job is parsed. A non-printing job will never set cDestinationSubsystem. When a page is ready to be printed (the intermediate has been built and the page is `closed' by the personality), cDestinationSubsystem will be set even if a page of a previous job is currently being printed. cDestinationSubsystem remains set until the last page of the job has finished printing. If a page requires extensive processing and allows all the previous pages of a job to complete printing, cDestinationSubsystem will remain set until the last page of the job has finished printing.
OBJECT-TYPE    
  STRING  

job-info-io-source 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.11
Indicates which I/O source, the print job was received over. The value maps to port numbering scheme supported in the DEVICE/SOURCE-SUBSYSTEM/IO/PORTS sub-tree.
OBJECT-TYPE    
  INTEGER  

job-info-pages-processed 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.12
Indicates the number of pages processed by the processing subsystem. If neither the cSourceSubsystem or the cProcessingSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the total number of pages processed for this job. The last OID field for this dynamic object contains the job ID. Additional information: This object is incremented by one when a page is processed (`closed' by the personality), regardless of the number of pages that are printed as a result of the single page processed. In other words, it does not matter how many identical copies of a page are printed or no pages may be printed if operating in silent run mode, this count is incremented exactly once. A page is considered processed when all of the input data has been processed for a page (that is, when the intermediate has been produced, and the personality has `closed' the page. At this time, the image of the page is not necessarily completely formed.)
OBJECT-TYPE    
  INTEGER  

job-info-pages-printed 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.13
Indicates the number of pages printed by the destination subsystem. If non of the cSourceSubsystem, cProcessingSubsystem or cDestinationSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the total number of pages printed for this job. This value may increase by two each time for duplex jobs. The last OID field for this dynamic object contains the job ID. Additional information: If multiple copies of a page are printed, each copy is counted individually.
OBJECT-TYPE    
  INTEGER  

job-info-size 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.14
Indicates the number of bytes of data processed by the processing subsystem. If neither of the cSourceSubsystem or cProcessingSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the size of this job, in bytes. The last OID field for this dynamic object contains the job ID. Additional information: This count may be incremented by values other than one as blocks of data are processed; blocks of data (which may be as large as 2K bytes) will be processed in a varying amount of time. During the processing of a job and even when a job completes, an exact count of the number of I/O bytes processed by the job is not necessarily to be expected.
OBJECT-TYPE    
  INTEGER  

job-info-state 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.15
Indicates the state of the job. The last OID field for this dynamic object contains the job ID. eAborted - the print job was aborted. eWaitingForResources - the print job requires resources that are not currently available. Example resources that can cause the job to wait include the print engine or PDL processor being unavailable. The print engine could be unavailable due to paper out, paper jam, staple out, stapler jam, marking agent low, output bin full, etc. The PDL processor could be unavailable due to an off-line condition. Each printer specific object specification should state which conditions cause a job to be waiting for resources and also state which objects can be retrieved by an application to determine the exact cause of a resource being unavailable. ePrinted - the job has printed. The related JOB-INFO- OUTCOME object indicates if any problems were encountered while the job was processed. eRetained - the job can be reprinted. eTerminating - the job was aborted or cancelled and is currently is terminating. eInterrupted - the job has been interrupted. The job can be continued. ePaused - the job has been paused. The job can be continuted. eCancelled - the job has been cancelled. eProcessing - the job is currently being printed normally.
OBJECT-TYPE    
  INTEGER eAborted(3), eWaitingForResources(4), ePrinted(5), eTerminating(7), eCancelled(10), eProcessing(11)  

job-info-outcome 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.19
Indicates if any warning or error conditions were encountered while processing the assoicated job. The last OID field for this dynamic object contains the job ID. Additional information: In LaserJet 4050 Series, warnings and errors are not recorded in this object. Although no meaningful information can be obtained from this object, it is kept around for the compatibility needs of existing software.
OBJECT-TYPE    
  INTEGER eOk(3)  

job-info-attr-1 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.1
Returns the value that was set in PJL via the SET JOBATTR= command. Attribute objects are saved sequentially, starting with 1, after the start of a job. If more attributes are set than there are objects to store them, the excess JOBATTR values are ignored. If the corresponding SET JOBATTR= command has not been received when a get is done for this object, a status of will be returned.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-2 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.2
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-3 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.3
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-4 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.4
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-5 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.5
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-6 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.6
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-7 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.7
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-8 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.8
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-9 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.9
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-10 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.10
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-11 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.11
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-12 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.12
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-13 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.13
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-14 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.14
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-15 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.15
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-16 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.16
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-17 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.17
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-18 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.18
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-19 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.19
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-20 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.20
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-21 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.21
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-22 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.22
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-23 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.23
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-24 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.24
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-25 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.25
Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OBJECT-TYPE    
  STRING Size(1..80)  

job-info-attr-26 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.26