HP-ICF-POE-MIB

File: HP-ICF-POE-MIB.mib (20335 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
HP-ICF-OID POWER-ETHERNET-MIB ENTITY-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
TruthValue MODULE-COMPLIANCE OBJECT-GROUP
hpicfCommon pethPsePortEntry entPhysicalIndex

Defined Types

HpicfPoePethPsePortEntry  
SEQUENCE    
  hpicfPoePethPsePortCurrent Integer32
  hpicfPoePethPsePortVoltage Integer32
  hpicfPoePethPsePortPower Integer32
  hpicfPoePethPsePortPowerAllocateBy INTEGER
  hpicfPoePethPsePortPowerValue Integer32
  hpicfPoePethPsePortLLDPDetect INTEGER
  hpicfPoePethPsePortPoePlusPowerValue Integer32
  hpicfPoePethPsePortActualPower Integer32

HpicfPseFeaturesEntry  
SEQUENCE    
  hpicfPseAllowPreStdDetect TruthValue
  hpicfPsePowerRedundancy INTEGER
  hpicfPseExtPwrSupplyCount Integer32
  hpicfPseAvailablePower Integer32
  hpicfPseUsedPower Integer32
  hpicfPseFailoverPower Integer32
  hpicfPseRedundantPower Integer32

HpicfPoePowerSupplyEntry  
SEQUENCE    
  hpicfPoePowerSupplySourceType INTEGER
  hpicfPoePowerSupplyType INTEGER
  hpicfPoePowerSupplyCapacity Integer32

Defined Values

hpicfPoe 1.3.6.1.4.1.11.2.14.11.1.9.1
This MIB module describes management objects used to manage Power Source Equipment (PSE).
MODULE-IDENTITY    

hpicfPOE 1.3.6.1.4.1.11.2.14.11.1.9
OBJECT IDENTIFIER    

hpicfPoePethPsePortTable 1.3.6.1.4.1.11.2.14.11.1.9.1.1
This table supplements the table 'pethPsePortTable' in ieee802af.mib.
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfPoePethPsePortEntry

hpicfPoePethPsePortEntry 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1
The fields in these entries will be used to supplement fields in 'pethPsePortEntry in ieee802af.mib.
OBJECT-TYPE    
  HpicfPoePethPsePortEntry  

hpicfPoePethPsePortCurrent 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.1
This field specifies the current supplied at this port. This value is specified in milli amperes(mA).
OBJECT-TYPE    
  Integer32 0..65535  

hpicfPoePethPsePortVoltage 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.2
This field specifies the Voltage supplied at this port. This value is specified in 10's of volts (dV)
OBJECT-TYPE    
  Integer32 0..65535  

hpicfPoePethPsePortPower 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.3
This field specifies the Power supplied at this port. This value is specified in milliwatts (mW).
OBJECT-TYPE    
  Integer32 0..65535  

hpicfPoePethPsePortPowerAllocateBy 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.4
This field specifies the power allocation method for this port. The default value is usage.
OBJECT-TYPE    
  INTEGER usage(1), class(2), value(3)  

hpicfPoePethPsePortPowerValue 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.5
This field specifies the power allocation defined for this port. This value is specified in Watts (W).
OBJECT-TYPE    
  Integer32 0..17  

hpicfPoePethPsePortLLDPDetect 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.6
This field specifies if power should be allocated using LLDP advertised information regarding the PD.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

hpicfPoePethPsePortPoePlusPowerValue 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.7
This field specifies the power allocation defined for this port. Use this object for equipment supporting high power, that is greater than 15 Watts. This value is specified in Watts (W). Maximum supported is 33W
OBJECT-TYPE    
  Integer32 0..255  

hpicfPoePethPsePortActualPower 1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.8
This field specifies the actual power drained by the device connected to this port.
OBJECT-TYPE    
  Integer32  

hpicfPoeAllowPreStdDetect 1.3.6.1.4.1.11.2.14.11.1.9.1.3
This object is used to configure the default POE power detection mode. A value of TRUE - indicates that power pre-802.3af-standard devices. A value of FALSE - indicates that only pre-802.3af compliant devices are allowed. The default value is true. In a stack, this value pertains only to the commander switch.
OBJECT-TYPE    
  TruthValue  

hpicfPoePowerRedundancy 1.3.6.1.4.1.11.2.14.11.1.9.1.4
This object is used to configure the POE power redundancy mode. A value of none(1) - means that all available power can be allocated to powered devices. A value of nPlus1(2) - means that one of the highest power supplies is held in reserve and that in the event of a single power supply failure, no no powered devices will be shut down. A value of full(3) - means that half of the available power supplies are held in reserve. The default value is none(1). In a stack, this value pertains only to the commander switch.
OBJECT-TYPE    
  INTEGER none(1), nPlus1(2), full(3)  

hpicfPoeExtPwrSupplyCount 1.3.6.1.4.1.11.2.14.11.1.9.1.5
This object is used to configure the number of external power supplies expected to be connected to the chassis. The default value is 1. In a stack, this value pertains only to the commander switch.
OBJECT-TYPE    
  Integer32 1..2147483647  

hpicfPseFeaturesTable 1.3.6.1.4.1.11.2.14.11.1.9.1.6
This table describes the features of each power source equipment (PSE). On standalone switches (both stackable and chassis switches) there shall be only one entry in this table. In a stack, there shall be one entry for each stack member.
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfPseFeaturesEntry

hpicfPseFeaturesEntry 1.3.6.1.4.1.11.2.14.11.1.9.1.6.1
A row in the PSE features table, signifying a single power source equipment.
OBJECT-TYPE    
  HpicfPseFeaturesEntry  

hpicfPseAllowPreStdDetect 1.3.6.1.4.1.11.2.14.11.1.9.1.6.1.1
This object is used to configure the default POE power detection mode for this power source equipment. A value of TRUE - indicates that power pre-802.3af-standard devices. A value of FALSE - indicates that only pre-802.3af compliant devices are allowed. The default value is true.
OBJECT-TYPE    
  TruthValue  

hpicfPsePowerRedundancy 1.3.6.1.4.1.11.2.14.11.1.9.1.6.1.2
This object is used to configure the POE power redundancy mode for this power source equipment. A value of none(1) - means that all available power can be allocated to powered devices. A value of nPlus1(2) - means that one of the highest power supplies is held in reserve and that in the event of a single power supply failure, no powered devices will be shut down. A value of full(3) - means that half of the available power supplies are held in reserve. The default value is none(1).
OBJECT-TYPE    
  INTEGER none(1), nPlus1(2), full(3)  

hpicfPseExtPwrSupplyCount 1.3.6.1.4.1.11.2.14.11.1.9.1.6.1.3
This object is used to configure the number of external power supplies expected to be connected to the Power Source Equipment. The default value is 1.
OBJECT-TYPE    
  Integer32 1..2147483647  

hpicfPseAvailablePower 1.3.6.1.4.1.11.2.14.11.1.9.1.6.1.4
This field specifies the total power available on this Power source equipment. This includes internal and external power supplies.
OBJECT-TYPE    
  Integer32 0..2147483647  

hpicfPseUsedPower 1.3.6.1.4.1.11.2.14.11.1.9.1.6.1.5
This field specifies the total power allocated on the Power Source Equipment. This is the sum of the power allocated to all the ports on the PSE.
OBJECT-TYPE    
  Integer32 0..2147483647  

hpicfPseFailoverPower 1.3.6.1.4.1.11.2.14.11.1.9.1.6.1.6
This field specifies the failover power for this Power Source Equipment.
OBJECT-TYPE    
  Integer32 0..2147483647  

hpicfPseRedundantPower 1.3.6.1.4.1.11.2.14.11.1.9.1.6.1.7
This field specifies the redundancy POE power available to the Power Source Equipment.
OBJECT-TYPE    
  Integer32 0..2147483647  

hpicfPoePowerSupplyTable 1.3.6.1.4.1.11.2.14.11.1.9.1.7
This table contains one row per power supply available to the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfPoePowerSupplyEntry

hpicfPoePowerSupplyEntry 1.3.6.1.4.1.11.2.14.11.1.9.1.7.1
Information about a particular power supply. Each entry provides information about power supply whether it is external or internal, if it is poe/poePlus and the capacity of the power supply.
OBJECT-TYPE    
  HpicfPoePowerSupplyEntry  

hpicfPoePowerSupplySourceType 1.3.6.1.4.1.11.2.14.11.1.9.1.7.1.1
This field specifies whether the power supply is external or internal. Stackable switch has inbuilt power supply and can have upto 1 external power supply. Chassis switch can have upto 2 internal power supplies for 6 slot and upto 4 for 12 slot. Chassis switch can have upto 2 external power supplies.
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

hpicfPoePowerSupplyType 1.3.6.1.4.1.11.2.14.11.1.9.1.7.1.2
This field specifies the type of the power supply, poe or poePlus.
OBJECT-TYPE    
  INTEGER poe(1), poePlus(2), notPresent(3), fault(4)  

hpicfPoePowerSupplyCapacity 1.3.6.1.4.1.11.2.14.11.1.9.1.7.1.3
This field specifies the capacity of the power supply.
OBJECT-TYPE    
  Integer32 0..2147483647  

hpicfPoeConformance 1.3.6.1.4.1.11.2.14.11.1.9.1.2
OBJECT IDENTIFIER    

hpicfPoeCompliances 1.3.6.1.4.1.11.2.14.11.1.9.1.2.1
OBJECT IDENTIFIER    

hpicfPoeGroups 1.3.6.1.4.1.11.2.14.11.1.9.1.2.2
OBJECT IDENTIFIER    

hpicfPoeCompliance 1.3.6.1.4.1.11.2.14.11.1.9.1.2.1.1
A Collection of Object(s) that display the current poe port status information.
MODULE-COMPLIANCE    

hpicfPoeCompliance1 1.3.6.1.4.1.11.2.14.11.1.9.1.2.1.2
A Collection of Object(s) that control the global (entire chassis) poe configuration.
MODULE-COMPLIANCE    

hpicfPoeCompliance2 1.3.6.1.4.1.11.2.14.11.1.9.1.2.1.3
A collection of Object(s) related to power supplies.
MODULE-COMPLIANCE    

hpicfPoePethPsePortTableGroup 1.3.6.1.4.1.11.2.14.11.1.9.1.2.2.1
A collection of objects allowing configuration of PoE PSE Port table
OBJECT-GROUP    

hpicfPoeGlobalGroup 1.3.6.1.4.1.11.2.14.11.1.9.1.2.2.2
A collection of objects related to the global configuration of POE on a given chassis.
OBJECT-GROUP    

hpicfPseFeaturesGroup 1.3.6.1.4.1.11.2.14.11.1.9.1.2.2.3
A Collection of Object(s) that provide information about each power source equipment instance.
OBJECT-GROUP    

hpicfPoePowerSupplyGroup 1.3.6.1.4.1.11.2.14.11.1.9.1.2.2.4
A collection of objects related to Power Supply.
OBJECT-GROUP