HP-ICF-FTRCO

File: HP-ICF-FTRCO.mib (15522 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMP-FRAMEWORK-MIB
SNMPv2-TC Q-BRIDGE-MIB HP-ICF-OID

Imported symbols

OBJECT-TYPE MODULE-IDENTITY Integer32
MODULE-COMPLIANCE OBJECT-GROUP SnmpAdminString
RowStatus TruthValue DateAndTime
TEXTUAL-CONVENTION PortList hpSwitch

Defined Types

VidList  
Each octet within this value specifies a set of eight VlanIIndex (VID), with the first octet specifying VIDs 1 through 8, the second octet specifying VIDs 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered VID, and the least significant bit represents the highest numbered VID. Thus, each VID is represented by a single bit within the value of this object. If that bit has a value of 1 then that VID is included in the set of VIDs; the VID is not included if its bit has a value of 0. This list represents the entire range of VlanIndex values defined in the scope of IEEE 802.1Q.
TEXTUAL-CONVENTION    
  OCTET STRING Size(512)  

IndexName  
This object is valid when used as an index - an IndexName is similar to a DisplayString, except that it does allow a tilde ('~') and spaces within ts definition. Otherwise it fully follows the textual-convention of the standard DisplayString definition.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..32)  

HpFtrcoEntityEntry  
SEQUENCE    
  hpFtrCoEntityName IndexName
  hpFtrCoRestrictNextIndex Integer32
  hpFtrCoEntityDate DateAndTime
  hpFtrCoEntityStatus RowStatus

HpFtrCoRestrictEntry  
SEQUENCE    
  hpFtrCoRestrictId INTEGER
  hpFtrCoRestrictIndex Integer32
  hpFtrCoRestrictIdParm Integer32
  hpFtrCoRestrictStatus RowStatus
  hpFtrCoRestrictMessage SnmpAdminString
  hpFtrCoRestrictPorts PortList
  hpFtrCoRestrictVlans VidList
  hpFtrCoExpireSlot Integer32
  hpFtrCoExpireApplication IndexName
  hpFtrCoExpireVidDelete Integer32
  hpFtrCoExpireDate DateAndTime
  hpFtrCoExpireBoot TruthValue

Defined Values

hpicfFtrCo 1.3.6.1.4.1.11.2.14.11.5.1.46
This MIB module manages Application Coordination Restriction Policies
MODULE-IDENTITY    

hpicfFtrcoObjects 1.3.6.1.4.1.11.2.14.11.5.1.46.1
OBJECT IDENTIFIER    

hpFtrCoEntityTable 1.3.6.1.4.1.11.2.14.11.5.1.46.1.1
Table of all Entities setting restrictions, as set by some external entity. Any restriction for an Entity can be deleted by deleting the Entity name, by deleting a specific restriction, or by any expiration value. Once an Entity name has been added to the table, it exist until the name has specifically been removed. Entity rows also maintain the 'next-index' value for any restriction table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpFtrcoEntityEntry

hpFtrCoEntityEntry 1.3.6.1.4.1.11.2.14.11.5.1.46.1.1.1
A row entry in the table for a specific entity user of the Feature Coordinator facility. Entries in this table are created and removed dynamically. An entity can add and remove a restriction regarding some pre-defined facility in the switch and it will only be for a specific Entity name. If the Entity name is removed, so are all of its restrictions.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpFtrcoEntityEntry  

hpFtrCoEntityName 1.3.6.1.4.1.11.2.14.11.5.1.46.1.1.1.1
An administratively assigned string, which may be used to identify the unique owner of a set of restrictions.
Status: current Access: not-accessible
OBJECT-TYPE    
  IndexName Size(1..32)  

hpFtrCoRestrictNextIndex 1.3.6.1.4.1.11.2.14.11.5.1.46.1.1.1.2
Is the next indexing parameter that allows multiple, like restrictions. It is has a default value of 1 and is incremented each time its index value is used. This is an independent value and must be specified as the next added index (regardless of the restriction type). In the event there is a collision due to a race with reading the current value, the 'losing' restriction is denied and the value should be re-read for a next attempt. The value is always 1 whenever a new Entity record is created.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

hpFtrCoEntityDate 1.3.6.1.4.1.11.2.14.11.5.1.46.1.1.1.3
This represents the switch's understanding of the current UTC time. It should be used when setting an restriction expiration DateAndTime value. Please note that this value is uniquely determined each time the object is read (dynamic) and is subject to changing when a change is made to the switch's configuration (e.g. setting the local time-zone).
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

hpFtrCoEntityStatus 1.3.6.1.4.1.11.2.14.11.5.1.46.1.1.1.4
Administrative status of this Entity entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hpFtrCoRestrictionTable 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2
Table of all restrictions, set by an external entity. The restrictions can be deleted by deleting the entity name or by the restriction expiration value. Expiration policies are logically ORed so that any policy expiration that is met causes the restriction to be removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpFtrCoRestrictEntry

hpFtrCoRestrictEntry 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1
An entry in the table for a specific Entity user of the Feature Coordinator facility. Entries in this table are created and removed dynamically. An entity can add and remove a restriction to some facility in the switch. These entries can also expire, based on entity specified criteria. A restriction is never modified (all restrictions are only created or deleted). If a value needs to be modified, a new restriction could be added and then the old one deleted (e.g. adding or removing an interface).
Status: current Access: not-accessible
OBJECT-TYPE    
  HpFtrCoRestrictEntry  

hpFtrCoRestrictId 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.1
The Restriction enumeration (Id). Expect this list to grow as are more restrictions are developed (and needed).
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER vidIpConfig(1), vidDelete(2), portSecurity(3), portAcl(4), portSourcePortFilter(5), portMeshing(6), portLacp(7), distributedTrunk(8), portVirusThrottling(9), portSflow(10), portDhcpSnoop(11), portLoopDetection(12), portBpduPvstGuard(13), qinq(14), portQos(15), portRateLimit(16), portStaticMac(17), portIpLockdown(18), portIgmp(19), portMirrorDestination(20), portLinkConfig(21), portLldp(22), portKeepalive(23), aclPermitLogging(24)  

hpFtrCoRestrictIndex 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.2
An indexing parameter to allow multiple, like restrictions. It is created by the Entity portion of MIB and used for addressing an individual restriction rule. Any new restriction added to a restriction table must be equal to the current 'next-restriction' value.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

hpFtrCoRestrictIdParm 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.3
An optional parameter for the restriction enumeration.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

hpFtrCoRestrictStatus 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.4
Administrative status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hpFtrCoRestrictMessage 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.5
An error message containing information about the restriction that can be used by the caller, indicating the reason for this restriction being in place. It is occasionally referred to as a friendly error message. SIZE reflects that a message must exist and that it has a maximum 'String' length of 255 character.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

hpFtrCoRestrictPorts 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.6
A list of ports, if applicable to the restriction.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

hpFtrCoRestrictVlans 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.7
A VidList of vlan IDs, if applicable to the restriction.
Status: current Access: read-create
OBJECT-TYPE    
  VidList  

hpFtrCoExpireSlot 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.8
Setting this value will cause this restriction to expire when corresponding switch slot is signaled to be down. Note, if the slot never comes up, there will be no slot-down signal.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

hpFtrCoExpireApplication 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.9
This setting will cause the restriction to expire whenever a signal is received that this application-name has gone down.
Status: current Access: read-create
OBJECT-TYPE    
  IndexName Size(0..32)  

hpFtrCoExpireVidDelete 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.10
A signal indicating this VlanIndex has been deleted will cause this restriction to expire. The specified VID record must exist in the switch configuration for this policy to be set. NOTE: ExpireVidDelete is unused in this release; it is available, you can set it; but it is totally ignored with current processing.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4096  

hpFtrCoExpireDate 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.11
This expiration event occurs whenever it is determined that the switch-time exceeds this setting. The switches sw_time() represents the UTC time value (relative to Jan 1, 1990) used with this comparison (compare with sw_localtime). NOTE: ExpireDate is unused in this release; it is available, you can set it; but it is totally ignored with current processing.
Status: current Access: read-create
OBJECT-TYPE    
  DateAndTime  

hpFtrCoExpireBoot 1.3.6.1.4.1.11.2.14.11.5.1.46.1.2.1.12
When specified as 'true', this expiration event occurs whenever the switch reboots. It is a necessary expiration policy since all restrictions are persistent and it is possible that we can have an obsolete policy (slot-down) following a power-fail condition.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hpicfFtrCoConformance 1.3.6.1.4.1.11.2.14.11.5.1.46.2
OBJECT IDENTIFIER    

hpicfFtrCoCompliances 1.3.6.1.4.1.11.2.14.11.5.1.46.2.1
OBJECT IDENTIFIER    

hpicfFtrCoGroups 1.3.6.1.4.1.11.2.14.11.5.1.46.2.2
OBJECT IDENTIFIER    

hpicfFtrCoCompliance 1.3.6.1.4.1.11.2.14.11.5.1.46.2.1.1
The compliance statement for HP switches implementing the HP-ICF-FTRCO-MIB.
Status: current Access: read-create
MODULE-COMPLIANCE    

hpicfFtrCoGroup 1.3.6.1.4.1.11.2.14.11.5.1.46.2.2.1
A collection of HP proprietary objects to support Feature Coordinator.
Status: current Access: read-create
OBJECT-GROUP