HH3C-NQA-MIB

Imported modules

SNMPv2-SMI	SNMPv2-TC	INET-ADDRESS-MIB
HH3C-OID-MIB	DISMAN-PING-MIB	SNMP-FRAMEWORK-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Unsigned32
OBJECT-IDENTITY	NOTIFICATION-TYPE	Integer32
Counter32	Gauge32	DateAndTime
DisplayString	RowStatus	InetAddressType
InetAddress	hh3cRhw	pingCtlEntry
pingCtlOwnerIndex	pingCtlTestName	pingCtlType
pingCtlTargetAddress	pingCtlTargetAddressType	pingCtlDescr
SnmpAdminString

Defined Types

Hh3cNqaCtlEntry
SEQUENCE
	hh3cNqaCtlTargetPort	Integer32
	hh3cNqaCtlSourcePort	Integer32
	hh3cNqaCtlTTL	Integer32
	hh3cNqaCtlJitterAdminInterval	Integer32
	hh3cNqaCtlJitterAdminNumPackets	Integer32
	hh3cNqaCtlHttpOperationType	INTEGER
	hh3cNqaCtlHttpOperationString	DisplayString
	hh3cNqaCtlFtpOperationType	INTEGER
	hh3cNqaCtlFtpUsername	DisplayString
	hh3cNqaCtlFtpPassword	DisplayString
	hh3cNqaCtlFtpOperationString	DisplayString
	hh3cNqaCtlVPNInstance	DisplayString
	hh3cNqaCtlHistoryKeptTime	Integer32
	hh3cNqaCtlHistoryEnable	INTEGER
	hh3cNqaCtlICPIFAdvFactor	Integer32
	hh3cNqaCtlCodecType	INTEGER

Hh3cNqaResultsEntry
SEQUENCE
	hh3cNqaResultsRttNumDisconnects	Unsigned32
	hh3cNqaResultsRttTimeouts	Unsigned32
	hh3cNqaResultsRttBusies	Unsigned32
	hh3cNqaResultsRttNoConnections	Unsigned32
	hh3cNqaResultsRttDrops	Unsigned32
	hh3cNqaResultsRttSequenceErrors	Unsigned32
	hh3cNqaResultsRttStatsErrors	Unsigned32
	hh3cNqaResultsMaxDelaySD	Unsigned32
	hh3cNqaResultsMaxDelayDS	Unsigned32
	hh3cNqaResultsLostPacketRatio	Unsigned32
	hh3cNqaResultsPacketLateArrival	Unsigned32
	hh3cNqaResultsRttSum	Unsigned32
	hh3cNqaResultsNumOfDelaySD	Unsigned32
	hh3cNqaResultsMinDelaySD	Unsigned32
	hh3cNqaResultsSumDelaySD	Unsigned32
	hh3cNqaResultsSum2DelaySD	Unsigned32
	hh3cNqaResultsNumOfDelayDS	Unsigned32
	hh3cNqaResultsMinDelayDS	Unsigned32
	hh3cNqaResultsSumDelayDS	Unsigned32
	hh3cNqaResultsSum2DelayDS	Unsigned32

Hh3cNqaJitterStatsEntry
SEQUENCE
	hh3cNqaJitterStatsNumOfRTT	Counter32
	hh3cNqaJitterStatsMinOfPositivesSD	Gauge32
	hh3cNqaJitterStatsMaxOfPositivesSD	Gauge32
	hh3cNqaJitterStatsNumOfPositivesSD	Gauge32
	hh3cNqaJitterStatsSumOfPositivesSD	Gauge32
	hh3cNqaJitterStatsSum2PositivesSD	Gauge32
	hh3cNqaJitterStatsMinOfNegativesSD	Gauge32
	hh3cNqaJitterStatsMaxOfNegativesSD	Gauge32
	hh3cNqaJitterStatsNumOfNegativesSD	Gauge32
	hh3cNqaJitterStatsSumOfNegativesSD	Gauge32
	hh3cNqaJitterStatsSum2NegativesSD	Gauge32
	hh3cNqaJitterStatsMinOfPositivesDS	Gauge32
	hh3cNqaJitterStatsMaxOfPositivesDS	Gauge32
	hh3cNqaJitterStatsNumOfPositivesDS	Gauge32
	hh3cNqaJitterStatsSumOfPositivesDS	Gauge32
	hh3cNqaJitterStatsSum2PositivesDS	Gauge32
	hh3cNqaJitterStatsMinOfNegativesDS	Gauge32
	hh3cNqaJitterStatsMaxOfNegativesDS	Gauge32
	hh3cNqaJitterStatsNumOfNegativesDS	Gauge32
	hh3cNqaJitterStatsSumOfNegativesDS	Gauge32
	hh3cNqaJitterStatsSum2NegativesDS	Gauge32
	hh3cNqaJitterStatsPacketLossSD	Gauge32
	hh3cNqaJitterStatsPacketLossDS	Gauge32
	hh3cNqaJitterStatsAvePositivesSD	Gauge32
	hh3cNqaJitterStatsAveNegativesSD	Gauge32
	hh3cNqaJitterStatsAvePositivesDS	Gauge32
	hh3cNqaJitterStatsAveNegativesDS	Gauge32
	hh3cNqaJitterStatsPktLossUnknown	Gauge32
	hh3cNqaJitterStatsOperOfICPIF	Gauge32
	hh3cNqaJitterStatsOperOfMOS	Gauge32

Hh3cNqaTcpServerEntry
SEQUENCE
	hh3cNqaTcpServerIpAddress	InetAddress
	hh3cNqaTcpServerPort	Integer32
	hh3cNqaTcpServerRowStatus	RowStatus

Hh3cNqaUdpServerEntry
SEQUENCE
	hh3cNqaUdpServerIpAddress	InetAddress
	hh3cNqaUdpServerPort	Integer32
	hh3cNqaUdpServerRowStatus	RowStatus

Hh3cNqaStatisticsCtlEntry
SEQUENCE
	hh3cNqaCtlStatisticsInterval	Unsigned32
	hh3cNqaCtlStatisticsGroupNumber	Unsigned32
	hh3cNqaCtlStatisticsKeptTime	Unsigned32
	hh3cNqaCtlBeginTime	DateAndTime
	hh3cNqaCtlLifeTime	Unsigned32

Hh3cNqaStatisticsResultsEntry
SEQUENCE
	hh3cNqaStatResIndex	Unsigned32
	hh3cNqaStatResIpTargetAddressType	InetAddressType
	hh3cNqaStatResIpTargetAddress	InetAddress
	hh3cNqaStatResMinRtt	Gauge32
	hh3cNqaStatResMaxRtt	Gauge32
	hh3cNqaStatResAverageRtt	Gauge32
	hh3cNqaStatResProbeResponses	Counter32
	hh3cNqaStatResSentProbes	Counter32
	hh3cNqaStatResRttSumOfSquares	Counter32
	hh3cNqaStatResStartTime	DateAndTime
	hh3cNqaStatResInterval	Gauge32
	hh3cNqaStatResRttNumDisconnects	Counter32
	hh3cNqaStatResRttTimeouts	Counter32
	hh3cNqaStatResRttBusies	Counter32
	hh3cNqaStatResRttNoConnections	Counter32
	hh3cNqaStatResRttDrops	Counter32
	hh3cNqaStatResRttSequenceErrors	Counter32
	hh3cNqaStatResRttErrors	Counter32
	hh3cNqaStatResLostPacketRatio	Gauge32
	hh3cNqaStatResPacketLateArrival	Counter32
	hh3cNqaStatResRttSum	Counter32
	hh3cNqaStatResNumOfDelaySD	Counter32
	hh3cNqaStatResMinDelaySD	Gauge32
	hh3cNqaStatResMaxDelaySD	Gauge32
	hh3cNqaStatResSumDelaySD	Counter32
	hh3cNqaStatResSum2DelaySD	Counter32
	hh3cNqaStatResNumOfDelayDS	Counter32
	hh3cNqaStatResMinDelayDS	Gauge32
	hh3cNqaStatResMaxDelayDS	Gauge32
	hh3cNqaStatResSumDelayDS	Counter32
	hh3cNqaStatResSum2DelayDS	Counter32

Hh3cNqaGroupStatsJitterEntry
SEQUENCE
	hh3cNqaStatJitterIndex	Unsigned32
	hh3cNqaStatJitterMinOfPosSD	Gauge32
	hh3cNqaStatJitterMaxOfPosSD	Gauge32
	hh3cNqaStatJitterNumOfPosSD	Counter32
	hh3cNqaStatJitterSumOfPosSD	Counter32
	hh3cNqaStatJitterSumOfSquarePosSD	Counter32
	hh3cNqaStatJitterMinOfNegSD	Gauge32
	hh3cNqaStatJitterMaxOfNegSD	Gauge32
	hh3cNqaStatJitterNumOfNegSD	Counter32
	hh3cNqaStatJitterSumOfNegSD	Counter32
	hh3cNqaStatJitterSumOfSquareNegSD	Counter32
	hh3cNqaStatJitterMinOfPosDS	Gauge32
	hh3cNqaStatJitterMaxOfPosDS	Gauge32
	hh3cNqaStatJitterNumOfPosDS	Counter32
	hh3cNqaStatJitterSumOfPosDS	Counter32
	hh3cNqaStatJitterSumOfSquarePosDS	Counter32
	hh3cNqaStatJitterMinOfNegDS	Gauge32
	hh3cNqaStatJitterMaxOfNegDS	Gauge32
	hh3cNqaStatJitterNumOfNegDS	Counter32
	hh3cNqaStatJitterSumOfNegDS	Counter32
	hh3cNqaStatJitterSumOfSquareNegDS	Counter32
	hh3cNqaStatJitterPacketLossSD	Counter32
	hh3cNqaStatJitterPacketLossDS	Counter32
	hh3cNqaStatJitterAvePosSD	Gauge32
	hh3cNqaStatJitterAveNegSD	Gauge32
	hh3cNqaStatJitterAvePosDS	Gauge32
	hh3cNqaStatJitterAveNegDS	Gauge32
	hh3cNqaStatJitterPktLossUnknown	Counter32
	hh3cNqaStatJitterMaxOfICPIF	Gauge32
	hh3cNqaStatJitterMinOfICPIF	Gauge32
	hh3cNqaStatJitterMaxOfMOS	Gauge32
	hh3cNqaStatJitterMinOfMOS	Gauge32

Hh3cNqaReactionEntry
SEQUENCE
	hh3cNqaReactOwnerIndex	SnmpAdminString
	hh3cNqaReactTestName	SnmpAdminString
	hh3cNqaReactItemIndex	Unsigned32
	hh3cNqaReactCheckedElement	INTEGER
	hh3cNqaReactThresholdUpperLimit	Unsigned32
	hh3cNqaReactThresholdLowerLimit	Unsigned32
	hh3cNqaReactThresholdType	INTEGER
	hh3cNqaReactThresholdConsecNum	Unsigned32
	hh3cNqaReactThresholdAccumNum	Unsigned32
	hh3cNqaReactActionType	INTEGER
	hh3cNqaReactCurrentStatus	INTEGER
	hh3cNqaReactRowStatus	RowStatus
	hh3cNqaReactCheckedNum	Unsigned32
	hh3cNqaReactThresholdNum	Unsigned32

Hh3cNqaStatisticsReactionEntry
SEQUENCE
	hh3cNqaStatReactOwnerIndex	SnmpAdminString
	hh3cNqaStatReactTestName	SnmpAdminString
	hh3cNqaStatReactIndex	Unsigned32
	hh3cNqaStatReactItemIndex	Unsigned32
	hh3cNqaStatReactCheckedNum	Counter32
	hh3cNqaStatReactThresholdNum	Counter32

Defined Values

hh3cNqa		1.3.6.1.4.1.25506.8.3
The private MIB file includes the test information of the device. It is supplementary for rfc2925.txt.
MODULE-IDENTITY

hh3cNqaObjects		1.3.6.1.4.1.25506.8.3.1
OBJECT IDENTIFIER

hh3cNqaImplementationTypeDomains		1.3.6.1.4.1.25506.8.3.2
OBJECT IDENTIFIER

hh3cNqaUdpEcho		1.3.6.1.4.1.25506.8.3.2.1
Indicates that an implementation is using the UDP based echo server. Notes: The hh3cNqaCtlTargetPort and hh3cNqaCtlSourcePort need to be set, while in the pingUdpEcho Node, hh3cNqaCtlTargetPort must be set to the default value.
Status: current	Access: read-only
OBJECT-IDENTITY

hh3cNqaTcpconnect		1.3.6.1.4.1.25506.8.3.2.2
Indicates that an implementation is attempting to connect to a TCP port in order to calculate a round trip time. Notes: The hh3cNqaCtlTargetPort and hh3cNqaCtlSourcePort need to be set, while in the pingTcpConnectionAttempt Node, hh3cNqaCtlTargetPort must be set to the default value.
Status: current	Access: read-only
OBJECT-IDENTITY

hh3cNqajitter		1.3.6.1.4.1.25506.8.3.2.3
Indicates that an implementation is using udp for packet transfers. 'jitter' will cause the NQA(Network Quality Analysis) application to perform delay variance analysis.
Status: current	Access: read-only
OBJECT-IDENTITY

hh3cNqaHttp		1.3.6.1.4.1.25506.8.3.2.4
Indicates that an implementation is using udp for name resolution, tcp connect and tcp data transfer mechanisms for HTTP data download from a particular HTTP Server. It causes the NQA application to perform a download of the object specified in the URL.
Status: current	Access: read-only
OBJECT-IDENTITY

hh3cNqadlsw		1.3.6.1.4.1.25506.8.3.2.5
Indicates that an implementation is using tcp for sending keepalives. 'dlsw' will cause the NQA application to perform a keepalive operation to measure the response time of a DLSw peer.
Status: current	Access: read-only
OBJECT-IDENTITY

hh3cNqadhcp		1.3.6.1.4.1.25506.8.3.2.6
Indicates that an implementation is using udp for sending dhcp requests. 'dhcp' will cause the NQA application to perform an IP Address lease request/teardown operation.
Status: current	Access: read-only
OBJECT-IDENTITY

hh3cNqaftp		1.3.6.1.4.1.25506.8.3.2.7
Indicates that an implementation is using tcp packet for ftp connect and data transfer.
Status: current	Access: read-only
OBJECT-IDENTITY

hh3cNqaMIBVersion		1.3.6.1.4.1.25506.8.3.1.1
Version string of this MIB. The format will be: 'Version.Release.Patch: Description' An instance likes: '1.0.0: Initial NQA MIB'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hh3cNqaCtlTable		1.3.6.1.4.1.25506.8.3.1.2
Defines the NQA Control Extend Table for providing, via SNMP, the capability of performing network analysis operations at a remote host.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaCtlEntry

hh3cNqaCtlEntry		1.3.6.1.4.1.25506.8.3.1.2.1
Defines an entry in the hh3cNqaCtlTable. The operation of this table is same as that of pingResultsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaCtlEntry

hh3cNqaCtlTargetPort		1.3.6.1.4.1.25506.8.3.1.2.1.1
The destination port that may be used by udpEcho, tcpConnect and jitter probes.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65536

hh3cNqaCtlSourcePort		1.3.6.1.4.1.25506.8.3.1.2.1.2
The source port that may be used by all tests except for dns and dlsw. If no source port is specified, system will create a random port as source port.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65536

hh3cNqaCtlTTL		1.3.6.1.4.1.25506.8.3.1.2.1.3
Specifies the value to store in the TTL Field in the IP packet used to encapsulate the NQA probe.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cNqaCtlJitterAdminInterval		1.3.6.1.4.1.25506.8.3.1.2.1.4
Time value in milliseconds that is an interval between two continuous probes in jitter test. This object is only used by jitter test.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..60000

hh3cNqaCtlJitterAdminNumPackets		1.3.6.1.4.1.25506.8.3.1.2.1.5
Packet number that specifys how many packets will be sent in one jitter test. This object is only used by jitter test.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cNqaCtlHttpOperationType		1.3.6.1.4.1.25506.8.3.1.2.1.6
Http operation type: get, post or raw.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	get(1), post(2), raw(3)

hh3cNqaCtlHttpOperationString		1.3.6.1.4.1.25506.8.3.1.2.1.7
Http operation string. For example, if the http operation type is get, the string will be url, home page and http version.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..1023)

hh3cNqaCtlFtpOperationType		1.3.6.1.4.1.25506.8.3.1.2.1.8
Ftp operation type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	get(1), put(2)

hh3cNqaCtlFtpUsername		1.3.6.1.4.1.25506.8.3.1.2.1.9
Ftp username.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

hh3cNqaCtlFtpPassword		1.3.6.1.4.1.25506.8.3.1.2.1.10
Ftp password.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

hh3cNqaCtlFtpOperationString		1.3.6.1.4.1.25506.8.3.1.2.1.11
Ftp operation string. If the ftp operation type is get, the string must be the file name which will be gotten from ftp server.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..255)

hh3cNqaCtlVPNInstance		1.3.6.1.4.1.25506.8.3.1.2.1.12
VPN name by which system finds route in the specified VPN to send NQA probe packets.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..255)

hh3cNqaCtlHistoryKeptTime		1.3.6.1.4.1.25506.8.3.1.2.1.13
To indicate how long the history records will be saved in the pingProbeHistoryTable table after the test stopped.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..1440

hh3cNqaCtlHistoryEnable		1.3.6.1.4.1.25506.8.3.1.2.1.14
To indicate whether the history should be recorded in the PingProbeHistoryTable or not. enabled(1) --history will be recorded disabled(2) --history will not be recorded.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

hh3cNqaCtlICPIFAdvFactor		1.3.6.1.4.1.25506.8.3.1.2.1.15
The advantage factor depends on the type of access and how the service is to be used. This object will be used while calculating the ICPIF (Calculated Planning Impairment Factor) values. This is applicable only for the jitter probe. Suggestion values: \|-----------------------------------\|-------\| \| Service \|factor \| \|-----------------------------------\|-------\| \|conventional wire-line \| 0 \| \|-----------------------------------\|-------\| \|mobility within Building \| 5 \| \|-----------------------------------\|-------\| \|mobility within geographical area \| 10 \| \|-----------------------------------\|-------\| \|access to hard-to-reach location \| 20 \| \|-----------------------------------\|-------\|
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cNqaCtlCodecType		1.3.6.1.4.1.25506.8.3.1.2.1.16
To indicate the codec type to be used with jitter probe. This is applicable only for the jitter probe.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notDefined(1), g711Alaw(2), g711Ulaw(3), g729A(4), icmpTimestamp(5)

hh3cNqaResultsTable		1.3.6.1.4.1.25506.8.3.1.3
Defines the NQA Results Extend Table for providing the capability of performing NQA operations at a remote host. The results of these operations are stored in the hh3cNqaResultsTable. The operation of this table is same as that of pingResultsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaResultsEntry

hh3cNqaResultsEntry		1.3.6.1.4.1.25506.8.3.1.3.1
The operation of this table is same as that of pingResultsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaResultsEntry

hh3cNqaResultsRttNumDisconnects		1.3.6.1.4.1.25506.8.3.1.3.1.1
The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsRttTimeouts		1.3.6.1.4.1.25506.8.3.1.3.1.2
The number of times that a NQA probe failed because the probe timed out.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsRttBusies		1.3.6.1.4.1.25506.8.3.1.3.1.3
The number of times that a NQA probe failed because all NQA tasks have been running. If a new probe fails to start, the value of this object is incremented. The next test will not start until the next Frequency.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsRttNoConnections		1.3.6.1.4.1.25506.8.3.1.3.1.4
The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsRttDrops		1.3.6.1.4.1.25506.8.3.1.3.1.5
The number of times that a NQA operation failed to initiated for unavailibility of necessary internal resources.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsRttSequenceErrors		1.3.6.1.4.1.25506.8.3.1.3.1.6
The number of packets arrived out of sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsRttStatsErrors		1.3.6.1.4.1.25506.8.3.1.3.1.7
The number of some other errors.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsMaxDelaySD		1.3.6.1.4.1.25506.8.3.1.3.1.8
The maximal delay from source device to destination device. Currently this value is only used for jitter test, and this value must be 0 in other type test. In jitter test, if destination system time is not valid, the SD delay may be set 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsMaxDelayDS		1.3.6.1.4.1.25506.8.3.1.3.1.9
The maximal delay from destination device to source device. Currently this value is only used for jitter test, and this value is 0 in other type test. In jitter test, if destination system time is not valid, the DS delay may be set 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsLostPacketRatio		1.3.6.1.4.1.25506.8.3.1.3.1.10
The value of this object reflects the drop rate of NQA test. For example, this value is 30 that means source device only had received 70% packets of total sent packets.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsPacketLateArrival		1.3.6.1.4.1.25506.8.3.1.3.1.11
The value of this object indicates the number of the packets that arrived after the timeout.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsRttSum		1.3.6.1.4.1.25506.8.3.1.3.1.12
The sum of round trip time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsNumOfDelaySD		1.3.6.1.4.1.25506.8.3.1.3.1.13
The number of delay from source to destination that are successfully measured.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsMinDelaySD		1.3.6.1.4.1.25506.8.3.1.3.1.14
The minimum of all one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsSumDelaySD		1.3.6.1.4.1.25506.8.3.1.3.1.15
The sum of one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsSum2DelaySD		1.3.6.1.4.1.25506.8.3.1.3.1.16
The sum of squares of one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsNumOfDelayDS		1.3.6.1.4.1.25506.8.3.1.3.1.17
The number of delay from destination to source that are successfully measured.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsMinDelayDS		1.3.6.1.4.1.25506.8.3.1.3.1.18
The minimum of all one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsSumDelayDS		1.3.6.1.4.1.25506.8.3.1.3.1.19
The sum of one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaResultsSum2DelayDS		1.3.6.1.4.1.25506.8.3.1.3.1.20
The sum of squares of one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaJitterStatsTable		1.3.6.1.4.1.25506.8.3.1.4
Statistics table for latest jitter activity.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaJitterStatsEntry

hh3cNqaJitterStatsEntry		1.3.6.1.4.1.25506.8.3.1.4.1
An entry contains the statistics for the latest jitter activity. This entry is created only if the pingCtlType is hh3cNqajitter.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaJitterStatsEntry

hh3cNqaJitterStatsNumOfRTT		1.3.6.1.4.1.25506.8.3.1.4.1.1
The number of received destination device responses with which jitter test can reach round-trip time.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaJitterStatsMinOfPositivesSD		1.3.6.1.4.1.25506.8.3.1.4.1.2
The value of time that records the minimal positive jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsMaxOfPositivesSD		1.3.6.1.4.1.25506.8.3.1.4.1.3
The value of time that records the maximal positive jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsNumOfPositivesSD		1.3.6.1.4.1.25506.8.3.1.4.1.4
The number that records positive jitter times from source to destination in the jitter test. The total number of the value of all positive jitters in packets sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsSumOfPositivesSD		1.3.6.1.4.1.25506.8.3.1.4.1.5
The value of time that records the sum of positive jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsSum2PositivesSD		1.3.6.1.4.1.25506.8.3.1.4.1.6
The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsMinOfNegativesSD		1.3.6.1.4.1.25506.8.3.1.4.1.7
The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsMaxOfNegativesSD		1.3.6.1.4.1.25506.8.3.1.4.1.8
The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsNumOfNegativesSD		1.3.6.1.4.1.25506.8.3.1.4.1.9
The number that records negative jitter times from source to destination in the jitter test. The total number of all negative jitter values in packets sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsSumOfNegativesSD		1.3.6.1.4.1.25506.8.3.1.4.1.10
The value of time that records the sum of negative jitter values from source to destination in the jitter test. The total number of the value of all negative jitters in packets sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsSum2NegativesSD		1.3.6.1.4.1.25506.8.3.1.4.1.11
The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsMinOfPositivesDS		1.3.6.1.4.1.25506.8.3.1.4.1.12
The value of time that records the minimal positive jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsMaxOfPositivesDS		1.3.6.1.4.1.25506.8.3.1.4.1.13
The value of time that records the maximal positive jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsNumOfPositivesDS		1.3.6.1.4.1.25506.8.3.1.4.1.14
The number that records positive jitter times from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsSumOfPositivesDS		1.3.6.1.4.1.25506.8.3.1.4.1.15
The value of time that records the sum of positive jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsSum2PositivesDS		1.3.6.1.4.1.25506.8.3.1.4.1.16
The value of time that records the sum of square of positive jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsMinOfNegativesDS		1.3.6.1.4.1.25506.8.3.1.4.1.17
The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsMaxOfNegativesDS		1.3.6.1.4.1.25506.8.3.1.4.1.18
The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsNumOfNegativesDS		1.3.6.1.4.1.25506.8.3.1.4.1.19
The number that records negative jitter times from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsSumOfNegativesDS		1.3.6.1.4.1.25506.8.3.1.4.1.20
The value of time that records the sum of negative jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsSum2NegativesDS		1.3.6.1.4.1.25506.8.3.1.4.1.21
The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsPacketLossSD		1.3.6.1.4.1.25506.8.3.1.4.1.22
The lost packets number sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsPacketLossDS		1.3.6.1.4.1.25506.8.3.1.4.1.23
The lost packets number sent from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsAvePositivesSD		1.3.6.1.4.1.25506.8.3.1.4.1.24
The value of time that records the average positive jitter value from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsAveNegativesSD		1.3.6.1.4.1.25506.8.3.1.4.1.25
The value of time that records the average negative jitter value from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsAvePositivesDS		1.3.6.1.4.1.25506.8.3.1.4.1.26
The value of time that records the average positive jitter value from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsAveNegativesDS		1.3.6.1.4.1.25506.8.3.1.4.1.27
The value of time that records the average negative jitter value from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsPktLossUnknown		1.3.6.1.4.1.25506.8.3.1.4.1.28
The number of packets which is lost with unknown reason.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsOperOfICPIF		1.3.6.1.4.1.25506.8.3.1.4.1.29
The ICPIF (Calculated Planning Impairment Factor) value for the latest jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaJitterStatsOperOfMOS		1.3.6.1.4.1.25506.8.3.1.4.1.30
The MOS (Mean Opinion Score) value for the latest jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaAgentEnable		1.3.6.1.4.1.25506.8.3.1.5
Enable NQA agent function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hh3cNqaTcpServerTable		1.3.6.1.4.1.25506.8.3.1.6
A table which contains the status of NQA tcp server configuration information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaTcpServerEntry

hh3cNqaTcpServerEntry		1.3.6.1.4.1.25506.8.3.1.6.1
A table which contains the status of NQA tcp server configuration information. This entry includes not only the tcp server ip address but also the tcp server port.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaTcpServerEntry

hh3cNqaTcpServerIpAddress		1.3.6.1.4.1.25506.8.3.1.6.1.1
Tcp server's ip address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

hh3cNqaTcpServerPort		1.3.6.1.4.1.25506.8.3.1.6.1.2
Tcp server's port number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65536

hh3cNqaTcpServerRowStatus		1.3.6.1.4.1.25506.8.3.1.6.1.3
hh3cNqaTcpServerIpAddress and hh3cNqaTcpServerPort must be set during a creation operation.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cNqaUdpServerTable		1.3.6.1.4.1.25506.8.3.1.7
Status of NQA udp server configuration information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaUdpServerEntry

hh3cNqaUdpServerEntry		1.3.6.1.4.1.25506.8.3.1.7.1
This entry includes not only the udp server ip address but also the udp server udp port.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaUdpServerEntry

hh3cNqaUdpServerIpAddress		1.3.6.1.4.1.25506.8.3.1.7.1.1
Udp server's ip address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

hh3cNqaUdpServerPort		1.3.6.1.4.1.25506.8.3.1.7.1.2
Udp server's port number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65536

hh3cNqaUdpServerRowStatus		1.3.6.1.4.1.25506.8.3.1.7.1.3
hh3cNqaUdpServerIpAddress and hh3cNqaUdpServerPort must be set during a creation operation.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cNqaServerEnable		1.3.6.1.4.1.25506.8.3.1.8
Enable NQA server function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hh3cNqaStatsMaxGroupNumber		1.3.6.1.4.1.25506.8.3.1.9
The maximum number saved per group. The maximum value of hh3cNqaCtlStatisticsGroupNumber can not exceed the value of this object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cNqaStatisticsCtlTable		1.3.6.1.4.1.25506.8.3.1.10
Defines the NQA statistics control table for providing, via SNMP, the capability of performing NQA operations at a remote host. The results of these operations are stored in the hh3cNqaStatisticsResultsTable and the hh3cNqaGroupStatsJitterTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaStatisticsCtlEntry

hh3cNqaStatisticsCtlEntry		1.3.6.1.4.1.25506.8.3.1.10.1
Defines an entry in the hh3cNqaStatisticsCtlTable. The hh3cNqaStatisticsCtlTable has the same index as the pingCtlTable in order for a hh3cNqaStatisticsCtlTable to correspond to the pingCtlEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaStatisticsCtlEntry

hh3cNqaCtlStatisticsInterval		1.3.6.1.4.1.25506.8.3.1.10.1.1
Statistic information will be calculated after the time that is the value of hh3cNqaCtlStatisticsInterval.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hh3cNqaCtlStatisticsGroupNumber		1.3.6.1.4.1.25506.8.3.1.10.1.2
The value of this object indicates the number of group saved. The length of this object is from 1 to hh3cNqaStatsMaxGroupNumber.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hh3cNqaCtlStatisticsKeptTime		1.3.6.1.4.1.25506.8.3.1.10.1.3
To indicate how long the statistic information will be saved after the test stops.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..1440

hh3cNqaCtlBeginTime		1.3.6.1.4.1.25506.8.3.1.10.1.4
Time at which the type-specified test will start.
Status: current	Access: read-create
OBJECT-TYPE
	DateAndTime

hh3cNqaCtlLifeTime		1.3.6.1.4.1.25506.8.3.1.10.1.5
To indicate how long the type-specified test will last.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hh3cNqaStatisticsResultsTable		1.3.6.1.4.1.25506.8.3.1.11
Defines the NQA statistics results table for providing the capability of performing NQA operations at a remote host. The statistics results of these operations in a statistic cycle are stored in the hh3cNqaStatisticsResultsTable. The statistic cycle is the value of hh3cNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that the probe statistics result (Hh3cNqaStatisticsResultsEntry) belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaStatisticsResultsEntry

hh3cNqaStatisticsResultsEntry		1.3.6.1.4.1.25506.8.3.1.11.1
Defines an entry in the hh3cNqaStatisticsResultsTable. The hh3cNqaStatisticsResultsTable has the same index as the pingCtlTable in order for a hh3cNqaStatisticsResultsEntry to correspond to the pingCtlEntry that caused it to be created.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaStatisticsResultsEntry

hh3cNqaStatResIndex		1.3.6.1.4.1.25506.8.3.1.11.1.1
An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hh3cNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..ffffffff

hh3cNqaStatResIpTargetAddressType		1.3.6.1.4.1.25506.8.3.1.11.1.2
This object indicates the type of address stored in the corresponding hh3cNqaStatResIpTargetAddress object.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

hh3cNqaStatResIpTargetAddress		1.3.6.1.4.1.25506.8.3.1.11.1.3
This object represent the host address to be used at a remote host for performing a network analysis operation.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

hh3cNqaStatResMinRtt		1.3.6.1.4.1.25506.8.3.1.11.1.4
The minimum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResMaxRtt		1.3.6.1.4.1.25506.8.3.1.11.1.5
The maximum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResAverageRtt		1.3.6.1.4.1.25506.8.3.1.11.1.6
The average NQA probe round-trip-time (RTT).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResProbeResponses		1.3.6.1.4.1.25506.8.3.1.11.1.7
The number of responses received. The value of this object MUST be reported as 0 when no probe responses have been received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResSentProbes		1.3.6.1.4.1.25506.8.3.1.11.1.8
The value of this object reflects the number of probes sent. The value of this object MUST be reported as 0 when no probes have been sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResRttSumOfSquares		1.3.6.1.4.1.25506.8.3.1.11.1.9
This object contains the sum of the squares for all NQA responses received. The value of this object MUST be reported as 0 when no NQA responses have been received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResStartTime		1.3.6.1.4.1.25506.8.3.1.11.1.10
This object contains the start time of the statistic.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hh3cNqaStatResInterval		1.3.6.1.4.1.25506.8.3.1.11.1.11
This object contains the interval between two times of statistic.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResRttNumDisconnects		1.3.6.1.4.1.25506.8.3.1.11.1.12
The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResRttTimeouts		1.3.6.1.4.1.25506.8.3.1.11.1.13
The number of times that a probe failed because the probe timed out.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResRttBusies		1.3.6.1.4.1.25506.8.3.1.11.1.14
The number of times that a NQA probe failed because errors related to sockets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResRttNoConnections		1.3.6.1.4.1.25506.8.3.1.11.1.15
The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResRttDrops		1.3.6.1.4.1.25506.8.3.1.11.1.16
The number of times that a NQA operation failed to initiate for unavailibility of necessary internal resources.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResRttSequenceErrors		1.3.6.1.4.1.25506.8.3.1.11.1.17
The number of packets arrived out of sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResRttErrors		1.3.6.1.4.1.25506.8.3.1.11.1.18
The number of other errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResLostPacketRatio		1.3.6.1.4.1.25506.8.3.1.11.1.19
The value of this object reflects the drop rate of NQA test packet. For example, if the value is 30, that means source device only had received 70 percent packets of total sent packets.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResPacketLateArrival		1.3.6.1.4.1.25506.8.3.1.11.1.20
The value of this object reflects the number of the packets that arrived after the timeout.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResRttSum		1.3.6.1.4.1.25506.8.3.1.11.1.21
This object contains the sum of the squares for all NQA responses received during the test lifetime. The value of this object MUST be reported as 0 when no NQA responses have been received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResNumOfDelaySD		1.3.6.1.4.1.25506.8.3.1.11.1.22
The number of one way times from source to destination that are successfully measured.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResMinDelaySD		1.3.6.1.4.1.25506.8.3.1.11.1.23
The minimum one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResMaxDelaySD		1.3.6.1.4.1.25506.8.3.1.11.1.24
The maximum one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResSumDelaySD		1.3.6.1.4.1.25506.8.3.1.11.1.25
The sum of one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResSum2DelaySD		1.3.6.1.4.1.25506.8.3.1.11.1.26
The sum of squares of one way times from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResNumOfDelayDS		1.3.6.1.4.1.25506.8.3.1.11.1.27
The number of one way times from destination to source that are successfully measured.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResMinDelayDS		1.3.6.1.4.1.25506.8.3.1.11.1.28
The minimum one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResMaxDelayDS		1.3.6.1.4.1.25506.8.3.1.11.1.29
The maximum one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatResSumDelayDS		1.3.6.1.4.1.25506.8.3.1.11.1.30
The sum of one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatResSum2DelayDS		1.3.6.1.4.1.25506.8.3.1.11.1.31
The sum of squares of one way times from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaGroupStatsJitterTable		1.3.6.1.4.1.25506.8.3.1.12
Test Group Statistic table for jitter activity in a statistic cycle. The statistic cycle is the value of hh3cNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that a probe statistics result (Hh3cNqaStatisticsResultsEntry) belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaGroupStatsJitterEntry

hh3cNqaGroupStatsJitterEntry		1.3.6.1.4.1.25506.8.3.1.12.1
An entry contains the group statistic information for jitter activity. This entry is created only if the pingCtlType is hh3cNqajitter.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaGroupStatsJitterEntry

hh3cNqaStatJitterIndex		1.3.6.1.4.1.25506.8.3.1.12.1.1
An entry in this table is created when the statistic result of a NQA probe in a statistic cycle is determined. An implementation MUST start assigning hh3cNqaStatJitterIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..ffffffff

hh3cNqaStatJitterMinOfPosSD		1.3.6.1.4.1.25506.8.3.1.12.1.2
The value of time that records the minimal positive jitter value from source to destination in jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterMaxOfPosSD		1.3.6.1.4.1.25506.8.3.1.12.1.3
The value of time that records the maximal positive jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterNumOfPosSD		1.3.6.1.4.1.25506.8.3.1.12.1.4
The total number of positive jitters from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterSumOfPosSD		1.3.6.1.4.1.25506.8.3.1.12.1.5
The value of time that records the sum of positive jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterSumOfSquarePosSD		1.3.6.1.4.1.25506.8.3.1.12.1.6
The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterMinOfNegSD		1.3.6.1.4.1.25506.8.3.1.12.1.7
The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterMaxOfNegSD		1.3.6.1.4.1.25506.8.3.1.12.1.8
The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterNumOfNegSD		1.3.6.1.4.1.25506.8.3.1.12.1.9
The total number of negative jitters from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterSumOfNegSD		1.3.6.1.4.1.25506.8.3.1.12.1.10
The value of time that records the sum of negative jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterSumOfSquareNegSD		1.3.6.1.4.1.25506.8.3.1.12.1.11
The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterMinOfPosDS		1.3.6.1.4.1.25506.8.3.1.12.1.12
The value of time that records the minimal positive jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterMaxOfPosDS		1.3.6.1.4.1.25506.8.3.1.12.1.13
The value of time that records the maximal positive jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterNumOfPosDS		1.3.6.1.4.1.25506.8.3.1.12.1.14
The total number of positive jitters from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterSumOfPosDS		1.3.6.1.4.1.25506.8.3.1.12.1.15
The value of time that records the sum of positive jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterSumOfSquarePosDS		1.3.6.1.4.1.25506.8.3.1.12.1.16
The value of time that records the sum of square of positive jitter values destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterMinOfNegDS		1.3.6.1.4.1.25506.8.3.1.12.1.17
The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterMaxOfNegDS		1.3.6.1.4.1.25506.8.3.1.12.1.18
The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterNumOfNegDS		1.3.6.1.4.1.25506.8.3.1.12.1.19
The total number of negative jitters from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterSumOfNegDS		1.3.6.1.4.1.25506.8.3.1.12.1.20
The value of time that records the sum of negative jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterSumOfSquareNegDS		1.3.6.1.4.1.25506.8.3.1.12.1.21
The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterPacketLossSD		1.3.6.1.4.1.25506.8.3.1.12.1.22
The lost packets number sent from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterPacketLossDS		1.3.6.1.4.1.25506.8.3.1.12.1.23
The lost packets number sent from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterAvePosSD		1.3.6.1.4.1.25506.8.3.1.12.1.24
The value of time that records the average positive jitter value from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterAveNegSD		1.3.6.1.4.1.25506.8.3.1.12.1.25
The value of time that records the average negative jitter value from source to destination.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterAvePosDS		1.3.6.1.4.1.25506.8.3.1.12.1.26
The value of time that records the average positive jitter value from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterAveNegDS		1.3.6.1.4.1.25506.8.3.1.12.1.27
The value of time that records the average negative jitter value from destination to source.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterPktLossUnknown		1.3.6.1.4.1.25506.8.3.1.12.1.28
The number of packets which is lost with unknown reason.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatJitterMaxOfICPIF		1.3.6.1.4.1.25506.8.3.1.12.1.29
The maximum of all ICPIF values in a statistic cycle for jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterMinOfICPIF		1.3.6.1.4.1.25506.8.3.1.12.1.30
The minimum of all ICPIF values in a statistic cycle for jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterMaxOfMOS		1.3.6.1.4.1.25506.8.3.1.12.1.31
The maximum of all MOS values in a statistic cycle for jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaStatJitterMinOfMOS		1.3.6.1.4.1.25506.8.3.1.12.1.32
The minimum of all MOS values in a statistic cycle for jitter test.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cNqaReactionTable		1.3.6.1.4.1.25506.8.3.1.13
A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaReactionEntry

hh3cNqaReactionEntry		1.3.6.1.4.1.25506.8.3.1.13.1
Defines an entry in the hh3cNqaReactionTable. The first two index elements identify the pingCtlEntry that a hh3cNqaReactItemIndex belongs to. The third index element selects a single reaction.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaReactionEntry

hh3cNqaReactOwnerIndex		1.3.6.1.4.1.25506.8.3.1.13.1.1
The first index of hh3cNqaReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable. hh3cNqaReactOwnerIndex and hh3cNqaReactTestName identify an existed test.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

hh3cNqaReactTestName		1.3.6.1.4.1.25506.8.3.1.13.1.2
The second index of hh3cNqaReactionTable, it is the same as pingCtlTestName in pingCtlTable. hh3cNqaReactOwnerIndex and hh3cNqaReactTestName identify an existed test.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

hh3cNqaReactItemIndex		1.3.6.1.4.1.25506.8.3.1.13.1.3
The third index of hh3cNqaReactionTable, it definitely identifies one of the reaction configurations for a test.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32	1..10

hh3cNqaReactCheckedElement		1.3.6.1.4.1.25506.8.3.1.13.1.4
A list of reaction condition type. 'probetime' and 'probefailure' are valid when pingCtlType of the test is not hh3cNqajitter. 'jitterOwdSD': one way time from source to destination in jitter test. 'jitterOwdDS': one way time from destination to source in jitter test. 'jitterrtt', 'jitterpacketloss', 'jittersd', 'jitterds', 'jitterOwdSD' and 'jitterOwdDS' are valid when pingCtlType of the test is hh3cNqajitter. 'icpif' and 'mos' are valid when pingCtlType of the test is hh3cNqajitter and hh3cNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	probetime(1), probefailure(2), jitterrtt(3), jitterpacketloss(4), jittersd(5), jitterds(6), icpif(7), mos(8), jitterOwdSD(9), jitterOwdDS(10)

hh3cNqaReactThresholdUpperLimit		1.3.6.1.4.1.25506.8.3.1.13.1.5
This object defines an administrative upper-threshold value for hh3cNqaReactCheckedElement. The value of this object is zero if hh3cNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hh3cNqaReactThresholdLowerLimit		1.3.6.1.4.1.25506.8.3.1.13.1.6
This object defines an administrative lower-threshold value for hh3cNqaReactCheckedElement. The value of hh3cNqaReactThresholdLowerLimit should be equal or less than the value of hh3cNqaReactThresholdUpperLimit. The value of this object is zero if hh3cNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hh3cNqaReactThresholdType		1.3.6.1.4.1.25506.8.3.1.13.1.7
This object defines the reaction threshold types. invalid(0): Invalid value. average(1): If reaction threshold type is average and the average value of watched operation exceeds threshold limit, an action specified in hh3cNqaReactActionType is generated when hh3cNqaReactCurrentStatus changes. consecutive(2): If reaction threshold type is consecutive and the times of watched operation consecutively exceeds the limit specified by hh3cNqaReactThresholdConsecNum, an action specified in hh3cNqaReactActionType is generated when hh3cNqaReactCurrentStatus changes. accumulative(3): If reaction threshold type is accumulative and the times of watched operation accumulatively exceeds the limit specified by hh3cNqaReactThresholdAccumNum, an action specified in hh3cNqaReactActionType is generated when hh3cNqaReactCurrentStatus changes. If reaction threshold type is not configured, the value of this object is 'invalid'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	invalid(0), average(1), consecutive(2), accumulative(3)

hh3cNqaReactThresholdConsecNum		1.3.6.1.4.1.25506.8.3.1.13.1.8
This object defines a consecutive threshold limit. The value is zero when hh3cNqaReactThresholdType is not 'consecutive'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hh3cNqaReactThresholdAccumNum		1.3.6.1.4.1.25506.8.3.1.13.1.9
This object defines an accumulative threshold limit. The value is zero when the hh3cNqaReactThresholdType is not 'accumulative'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

hh3cNqaReactActionType		1.3.6.1.4.1.25506.8.3.1.13.1.10
Specifies the type of reaction to generate if the specified violation type occurs for the monitored element: none - No reaction is generated trapOnly - A trap is generated triggerOnly - All trigger actions defined for this entry are generated trapAndTrigger - Both a trap and all trigger actions are generated
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), trapOnly(1), triggerOnly(2), trapAndTrigger(3)

hh3cNqaReactCurrentStatus		1.3.6.1.4.1.25506.8.3.1.13.1.11
Specifies the current status of this reaction entry: invalid - The status of the reaction entry is unknown. overThreshold - The status of the reaction entry is overThreshold when the monitored result exceeds the threshold value for the hh3cNqaReactThresholdType. belowThreshold - The status of the reaction entry is belowThreshold when the monitored result is under the threshold value for the hh3cNqaReactThresholdType.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	invalid(1), overThreshold(2), belowThreshold(3)

hh3cNqaReactRowStatus		1.3.6.1.4.1.25506.8.3.1.13.1.12
This object allows entries to be created and deleted in the hh3cNqaReactionTable. Creation of an entry in this table results in a new set of reaction configurations which take effect immediately. Deletion of an entry in this table results in corresponding reaction configurations are being deleted and stop taking effect.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cNqaReactCheckedNum		1.3.6.1.4.1.25506.8.3.1.13.1.13
The number of checked element samples that are monitored.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaReactThresholdNum		1.3.6.1.4.1.25506.8.3.1.13.1.14
The number of checked element samples that are over threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cNqaStatisticsReactionTable		1.3.6.1.4.1.25506.8.3.1.14
A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cNqaStatisticsReactionEntry

hh3cNqaStatisticsReactionEntry		1.3.6.1.4.1.25506.8.3.1.14.1
Defines an entry in the hh3cNqaStatisticsReactionTable. The first two index elements identify the pingCtlEntry that a hh3cNqaReactItemIndex belongs to. The third index element identifies an entry in the hh3cNqaStatisticsResultsTable. The forth index element selects a single reaction.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cNqaStatisticsReactionEntry

hh3cNqaStatReactOwnerIndex		1.3.6.1.4.1.25506.8.3.1.14.1.1
The first index of hh3cNqaStatisticsReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

hh3cNqaStatReactTestName		1.3.6.1.4.1.25506.8.3.1.14.1.2
The second index of hh3cNqaStatisticsReactionTable, it is the same as pingCtlTestName in pingCtlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

hh3cNqaStatReactIndex		1.3.6.1.4.1.25506.8.3.1.14.1.3
The third index of hh3cNqaStatisticsReactionTable. An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hh3cNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hh3cNqaStatReactItemIndex		1.3.6.1.4.1.25506.8.3.1.14.1.4
The forth index of hh3cNqaStatisticsReactionTable, it definitely identifies one of the reaction configurations for a test
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

hh3cNqaStatReactCheckedNum		1.3.6.1.4.1.25506.8.3.1.14.1.5
The number of checked element samples that are monitored.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaStatReactThresholdNum		1.3.6.1.4.1.25506.8.3.1.14.1.6
The number of checked element samples that are over threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cNqaNotifications		1.3.6.1.4.1.25506.8.3.3
OBJECT IDENTIFIER

hh3cNqaProbeTimeOverThreshold		1.3.6.1.4.1.25506.8.3.3.1
It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. Probe time(equals to RTT for some type of tests) is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit. 2. The probe time is accumulatively not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdAccumNum. 3. The probe time is consecutively in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdConsecNum. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hh3cNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cNqaJitterRTTOverThreshold		1.3.6.1.4.1.25506.8.3.3.2
It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average NQA round-trip-time (RTT) of jitter packets is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit. 2. The RTT of jitter packets is accumulatively not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdAccumNum in one test. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hh3cNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cNqaProbeFailure		1.3.6.1.4.1.25506.8.3.3.3
It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the probe test accumulatively failed for a number of times specified in hh3cNqaReactThresholdAccumNum in one test while the value of hh3cNqaReactThresholdType is 'accumulative'. 2. When the probe test consecutively failed for a number of times specified in hh3cNqaReactThresholdConsecNum in one test while the value of hh3cNqaReactThresholdType is 'consecutive'. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hh3cNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cNqaJitterPacketLoss		1.3.6.1.4.1.25506.8.3.3.4
It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the jitter packets accumulatively lost for a number of times specified in hh3cNqaReactThresholdAccumNum in one test while the value of hh3cNqaReactThresholdType is 'accumulative'. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hh3cNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cNqaJitterSDOverThreshold		1.3.6.1.4.1.25506.8.3.3.5
The SD means the jitter values from source to destination. It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of SD in one jitter test is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit and the hh3cNqaReactThresholdType is specified as 'average' type. 2. The average of SD in one jitter test is accumulatively not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdAccumNum and the hh3cNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hh3cNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cNqaJitterDSOverThreshold		1.3.6.1.4.1.25506.8.3.3.6
The DS means the jitter values from destination to source. It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of DS in one jitter test is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit and the hh3cNqaReactThresholdType is specified as 'average' type. 2. The average of DS in one jitter test is accumulatively not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdAccumNum and the hh3cNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hh3cNqajitter.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cNqaICPIFOverThreshold		1.3.6.1.4.1.25506.8.3.3.7
It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the ICPIF value in one jitter test is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hh3cNqajitter and hh3cNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cNqaMOSOverThreshold		1.3.6.1.4.1.25506.8.3.3.8
It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the MOS value in one jitter test is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hh3cNqajitter and hh3cNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current	Access: read-only
NOTIFICATION-TYPE