HH3C-MPLS-LDP-MIB

File: HH3C-MPLS-LDP-MIB.mib (76226 bytes)

Imported modules

HH3C-OID-MIB SNMPv2-SMI SNMPv2-CONF
SNMPv2-TC

Imported symbols

hh3cMpls OBJECT-TYPE MODULE-IDENTITY
NOTIFICATION-TYPE Integer32 Counter32
Unsigned32 IpAddress MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP TEXTUAL-CONVENTION
TruthValue RowStatus TimeInterval

Defined Types

DisplayString  
OCTET STRING Size(0..255)    

PhysAddress  
OCTET STRING    

BitRate  
INTEGER    

BurstSize  
INTEGER    

MplsLsrIdentifier  
The Label Switch Router (LSR) identifier is the first 4 bytes or the IP Address component of the Label Distribution Protocol (LDP) identifier.
TEXTUAL-CONVENTION    
  OCTET STRING Size(4)  

MplsLdpGenAddr  
The value of an network layer or data link layer address.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..64)  

MplsLdpIdentifier  
The LDP identifier is a six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific label space within the LSR.
TEXTUAL-CONVENTION    
  OCTET STRING Size(6)  

AtmVpIdentifier  
The VPI value for a VPL. The value VPI=0 is not used for a VPL not associated with a VCL. For ATM UNIs supporting VPCs the VPI value ranges from 1 to 255. For ATM UNIs supporting VCCs the VPI value ranges from 0 to 255. The maximum VPI value cannot exceed the value allowable by atmInterfaceMaxVpiBits defined in ATM-MIB.
TEXTUAL-CONVENTION    
  INTEGER 0..4095  

AtmVcIdentifier  
The VCI value for a VCL. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB.
TEXTUAL-CONVENTION    
  INTEGER 0..65535  

AddressFamilyNumbers  
An address family. Values are defined in RFC 1700 - Assigned Numbers. All values may not be relevant in all contexts when used in this MIB, but are included for completeness.
TEXTUAL-CONVENTION    
  INTEGER other(0), ipv4(1), ipv6(2), nsap(3), hdlc(4), bbn1822(5), ieee802(6), e163(7), e164(8), f69(9), x121(10), ipx(11), appleTalk(12), decnetIV(13), banyanVines(14), e164WithNsap(15)  

MplsLabel  
Represents an MPLS label. Note that the contents of a label field are interpreted in an interface-type specific fashion. For example, the label carried in the MPLS shim header is 20 bits wide and the top 12 bits must be zero. The frame relay label can be either 10, 17 or 23 bits wide depending on the size of the DLCI field size and the top 22, 15, or 9 bits must be zero, respectively. For an ATM interface, the lowermost 16 bits are interpreted as the VCI, the next 8 bits as the VPI and the remaining bits must be zero. Also note the permissible label values are also a function of the interface type. For example, the value 3 has special semantics in the control plane for an MPLS shim header label and is not a valid label value in the datapath.
TEXTUAL-CONVENTION    
  INTEGER  

MplsTunnelIndex  
Index into mplsTunnelTable.
TEXTUAL-CONVENTION    
  INTEGER 0..65535  

Hh3cMplsLdpLsrIncarnEntry  
SEQUENCE    
  hh3cMplsLdpLsrID MplsLsrIdentifier
  hh3cMplsLdpLsrLoopDetectionPresent TruthValue
  hh3cMplsLdpLsrLoopDetectionAdminStatus INTEGER
  hh3cMplsLdpLsrPathVectorLimit INTEGER
  hh3cMplsLdpLsrHopCountLimit INTEGER
  hh3cMplsLdpLsrLoopPreventionPresent TruthValue
  hh3cMplsLdpLsrLoopPreventionAdminStatus INTEGER
  hh3cMplsLdpLsrLabelRetentionMode INTEGER
  hh3cMplsLdpLsrIncarnID INTEGER
  hh3cMplsLdpLsrMaxLdpEntities INTEGER
  hh3cMplsLdpLsrMaxLocalPeers INTEGER
  hh3cMplsLdpLsrMaxRemotePeers INTEGER
  hh3cMplsLdpLsrMaxIfaces INTEGER
  hh3cMplsLdpLsrMaxLsps INTEGER
  hh3cMplsLdpLsrMaxCrlspTnls INTEGER
  hh3cMplsLdpLsrMaxErhopPerCrlspTnl INTEGER
  hh3cMplsLdpLsrRowStatus RowStatus
  hh3cMplsLdpLsrMaxVcmCapability INTEGER
  hh3cMplsLdpLsrVcmPathVecInAllLblMapPresent TruthValue
  hh3cMplsLdpLsrRequestRetrytimerValue INTEGER
  hh3cMplsLdpLsrNumOfRequestRetryAttempts INTEGER

Hh3cMplsLdpEntityEntry  
SEQUENCE    
  hh3cMplsLdpEntityID MplsLdpIdentifier
  hh3cMplsLdpEntityLabelSpaceType INTEGER
  hh3cMplsLdpEntityDefVpi AtmVpIdentifier
  hh3cMplsLdpEntityDefVci AtmVcIdentifier
  hh3cMplsLdpEntityUnlabTrafVpi AtmVpIdentifier
  hh3cMplsLdpEntityUnlabTrafVci AtmVcIdentifier
  hh3cMplsLdpEntityMergeCapability INTEGER
  hh3cMplsLdpEntityVcDirectionality INTEGER
  hh3cMplsLdpEntityWellKnownDiscoveryPort INTEGER
  hh3cMplsLdpEntityMtu INTEGER
  hh3cMplsLdpEntityKeepAliveHoldTimer INTEGER
  hh3cMplsLdpEntityFailedInitSessionThreshold INTEGER
  hh3cMplsLdpEntityLabelDistributionMethod INTEGER
  hh3cMplsLdpEntityLabelAllocationMethod INTEGER
  hh3cMplsLdpEntityHelloHoldTimer INTEGER
  hh3cMplsLdpEntityRowStatus RowStatus

Hh3cMplsLdpEntityIfEntry  
SEQUENCE    
  hh3cMplsLdpEntityIfIndex Unsigned32
  hh3cMplsLdpEntityIfIpv4Address IpAddress
  hh3cMplsLdpEntityIfRowStatus RowStatus

Hh3cMplsLdpEntityConfAtmLabelRangeEntry  
SEQUENCE    
  hh3cMplsLdpEntityConfAtmLabelRangeLowerBoundVPI AtmVpIdentifier
  hh3cMplsLdpEntityConfAtmLabelRangeLowerBoundVCI AtmVcIdentifier
  hh3cMplsLdpEntityConfAtmLabelRangeUpperBoundVPI AtmVpIdentifier
  hh3cMplsLdpEntityConfAtmLabelRangeUpperBoundVCI AtmVcIdentifier
  hh3cMplsLdpEntityConfAtmLabelRangeRowStatus RowStatus

Hh3cMplsLdpEntityStatsEntry  
SEQUENCE    
  hh3cMplsLdpAttemptedSessions Counter32

Hh3cMplsLdpPeerEntry  
SEQUENCE    
  hh3cMplsLdpPeerIndex Unsigned32
  hh3cMplsLdpPeerID MplsLdpIdentifier
  hh3cMplsLdpPeerInternetworkAddrType AddressFamilyNumbers
  hh3cMplsLdpPeerInternetworkAddr MplsLdpGenAddr
  hh3cMplsLdpPeerDefaultMtu INTEGER
  hh3cMplsLdpPeerKeepAliveHoldTimer INTEGER
  hh3cMplsLdpPeerLabelDistributionMethod INTEGER
  hh3cMplsLdpPeerType INTEGER
  hh3cMplsLdpPeerRowStatus RowStatus

Hh3cMplsLdpPeerConfAtmLabelRangeEntry  
SEQUENCE    
  hh3cMplsLdpPeerConfAtmLabelRangeLowerBoundVPI AtmVpIdentifier
  hh3cMplsLdpPeerConfAtmLabelRangeLowerBoundVCI AtmVcIdentifier
  hh3cMplsLdpPeerConfAtmLabelRangeUpperBoundVPI AtmVpIdentifier
  hh3cMplsLdpPeerConfAtmLabelRangeUpperBoundVCI AtmVcIdentifier

Hh3cMplsLdpSessionEntry  
SEQUENCE    
  hh3cMplsLdpSessionIndex Unsigned32
  hh3cMplsLdpSessionID MplsLdpIdentifier
  hh3cMplsLdpSessionProtocolVersion INTEGER
  hh3cMplsLdpSessionKeepAliveHoldTimeRemaining TimeInterval
  hh3cMplsLdpSessionRole INTEGER
  hh3cMplsLdpSessionState INTEGER
  hh3cMplsLdpSessionAtmLabelRangeLowerBoundVPI AtmVpIdentifier
  hh3cMplsLdpSessionAtmLabelRangeLowerBoundVCI AtmVcIdentifier
  hh3cMplsLdpSessionAtmLabelRangeUpperBoundVPI AtmVpIdentifier
  hh3cMplsLdpSessionAtmLabelRangeUpperBoundVCI AtmVcIdentifier

Hh3cMplsLdpHelloAdjacencyEntry  
SEQUENCE    
  hh3cMplsLdpHelloAdjacencyIndex Unsigned32
  hh3cMplsLdpHelloAdjacencyHoldTimeRemaining TimeInterval

Hh3cMplsLdpCrlspTnlEntry  
SEQUENCE    
  hh3cMplsLdpCrlspTnlIndex MplsTunnelIndex
  hh3cMplsLdpCrlspTnlName DisplayString
  hh3cMplsLdpCrlspTnlDirection INTEGER
  hh3cMplsLdpCrlspTnlSignallingProto INTEGER
  hh3cMplsLdpCrlspTnlSetupPrio INTEGER
  hh3cMplsLdpCrlspTnlHoldingPrio INTEGER
  hh3cMplsLdpCrlspTnlPeakDataRate BitRate
  hh3cMplsLdpCrlspTnlPeakBurstSize BurstSize
  hh3cMplsLdpCrlspTnlCommittedDataRate BitRate
  hh3cMplsLdpCrlspTnlCommittedBurstSize BurstSize
  hh3cMplsLdpCrlspTnlExcessBurstSize BurstSize
  hh3cMplsLdpCrlspTnlIsPinned TruthValue
  hh3cMplsLdpCrlspTnlFrequency INTEGER
  hh3cMplsLdpCrlspTnlWeight INTEGER
  hh3cMplsLdpCrlspTnlRowStatus RowStatus

Hh3cMplsLdpCrlspErHopEntry  
SEQUENCE    
  hh3cMplsLdpCrlspErHopIndex INTEGER
  hh3cMplsLdpCrlspErHopAddrType INTEGER
  hh3cMplsLdpCrlspErHopIpv4Addr IpAddress
  hh3cMplsLdpCrlspErHopIpv4PrefixLen INTEGER
  hh3cMplsLdpCrlspErHopStrictOrLoose INTEGER
  hh3cMplsLdpCrlspErHopRowStatus RowStatus

Defined Values

hh3cMplsLdp 1.3.6.1.4.1.25506.8.12.2
All rights reserved
MODULE-IDENTITY    

hh3cMplsLdpObjects 1.3.6.1.4.1.25506.8.12.2.1
OBJECT IDENTIFIER    

hh3cMplsLdpNotifications 1.3.6.1.4.1.25506.8.12.2.2
OBJECT IDENTIFIER    

hh3cMplsLdpLsrObjects 1.3.6.1.4.1.25506.8.12.2.1.1
OBJECT IDENTIFIER    

hh3cMplsLdpEntityObjects 1.3.6.1.4.1.25506.8.12.2.1.2
OBJECT IDENTIFIER    

hh3cMplsLdpPeerObjects 1.3.6.1.4.1.25506.8.12.2.1.3
OBJECT IDENTIFIER    

hh3cMplsLdpSessionObjects 1.3.6.1.4.1.25506.8.12.2.1.4
OBJECT IDENTIFIER    

hh3cMplsLdpHelloAdjacencyObjects 1.3.6.1.4.1.25506.8.12.2.1.5
OBJECT IDENTIFIER    

hh3cMplsLdpCrlspTnlObjects 1.3.6.1.4.1.25506.8.12.2.1.6
OBJECT IDENTIFIER    

hh3cMplsLdpLsrIncarnTable 1.3.6.1.4.1.25506.8.12.2.1.1.1
H3CMPLS provides support for multiple incarnations of the MPLS Stack in a target. The LSR defined in the standard MIB is treated as an incarnation in this MIB. Using a local policy the Network administrator must group the LDP Entities that should be placed in an incarnation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpLsrIncarnEntry

hh3cMplsLdpLsrIncarnEntry 1.3.6.1.4.1.25506.8.12.2.1.1.1.1
An entry in this table represents an LSR incarnation. All the entries in this table are created initially when the LDP is initiated. The row status of each entry will be in 'notInService' state initially. The row status must be set to 'active' after the necessary configurations are complete with respect to an incarnation. Currenlty the LSR ID of the incarnation is the only mandatory parameter that must be set before the rowStatus is set to 'active'. An LSR Incarnation Entity is uniquely indexed by its Incarnation Identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpLsrIncarnEntry  

hh3cMplsLdpLsrID 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.1
The LSR's Identifier.
Status: current Access: read-write
OBJECT-TYPE    
  MplsLsrIdentifier  

hh3cMplsLdpLsrLoopDetectionPresent 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.2
A indication of whether this LSR supports loop detection. A value of 'true' indicates this LSR does support loop detection. A value of 'false' indicates this LSR does not support loop detection.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hh3cMplsLdpLsrLoopDetectionAdminStatus 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.3
To enable loop detection the value of this object should be 'enabled(1)'. Otherwise, to turn off loop detection, set this value to 'disabled(2)'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hh3cMplsLdpLsrPathVectorLimit 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.4
This object only has meaning if hh3cMplsLdpLsrLoopDetectionPresent has the value of 'true'. The value of this object represents the limit of path vectors which this LSR uses to treat the message as if it had traversed a loop.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrHopCountLimit 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.5
This object only has meaning if hh3cMplsLdpLsrLoopDetectionPresent has the value of 'true'. The value of this object represents the limit on the Hop Count which this LSR uses to treat the message as if it had traversed a loop.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrLoopPreventionPresent 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.6
A indication of whether this LSR supports loop prevention. A value of 'true' indicates this LSR does support loop prevention. A value of 'false' indicates this LSR does not support loop prevention. Current release of H3CMPLS does not provide support to assign this MIB object with a value 'true'.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hh3cMplsLdpLsrLoopPreventionAdminStatus 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.7
To enable loop prevention the value of this object should be 'enabled(1)'. Otherwise, to turn off loop prevention, set this value to 'disabled(2)'. Current release of H3CMPLS does not provide support to assign this MIB object with a value 'enabled'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hh3cMplsLdpLsrLabelRetentionMode 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.8
The LSR can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized label mappings are retained only if they will be used to forward packets, i.e. if label came from a valid next hop. If the value of this object is liberal(2) then all advertized label mappings are retained whether they are from a valid next hop or not. Current release of H3CMPLS does not provide support to assign this MIB object with a value 'liberal'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER conservative(1), liberal(2)  

hh3cMplsLdpLsrIncarnID 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.9
The incarnation acts as index to all the elements in this table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrMaxLdpEntities 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.10
The maximum number of LDP entities that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1024  

hh3cMplsLdpLsrMaxLocalPeers 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.11
The maximum number of Local LDP peers that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1024  

hh3cMplsLdpLsrMaxRemotePeers 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.12
The maximum number of Remote LDP peers that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1024  

hh3cMplsLdpLsrMaxIfaces 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.13
The maximum number of Label enabled Interfaces that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrMaxLsps 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.14
The maximum number of Label Switched Paths that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrMaxCrlspTnls 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.15
The maximum number of CRLSPs that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrMaxErhopPerCrlspTnl 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.16
The maximum number of ER-Hops that can be supported in a CRLSP tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrRowStatus 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.17
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hh3cMplsLdpLsrMaxVcmCapability 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.18
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrVcmPathVecInAllLblMapPresent 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.19
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hh3cMplsLdpLsrRequestRetrytimerValue 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.20
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpLsrNumOfRequestRetryAttempts 1.3.6.1.4.1.25506.8.12.2.1.1.1.1.21
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpEntityTable 1.3.6.1.4.1.25506.8.12.2.1.2.1
This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switch Router (LSR).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpEntityEntry

hh3cMplsLdpEntityEntry 1.3.6.1.4.1.25506.8.12.2.1.2.1.1
An entry in this table represents an LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. An LPD Entity is uniquely indexed by its LPD Identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpEntityEntry  

hh3cMplsLdpEntityID 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.1
The LDP identifier which uniquely identifies the LDP Entity. This is s six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific label space within the LSR.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MplsLdpIdentifier  

hh3cMplsLdpEntityLabelSpaceType 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.2
The type of label spaces associated with this LDP Entity. The values are 'unknown(1)' The type of label space is not known. 'perInterface(2)' The type of label space is tied to an interface. 'perPlatform(3)' The type of label space is tied to the platform.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unknown(1), perInterface(2), perPlatform(3)  

hh3cMplsLdpEntityDefVpi 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.3
The Default VPI value used in the label for the default VPI.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

hh3cMplsLdpEntityDefVci 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.4
The Default VCI value used in the label for the default VCI.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

hh3cMplsLdpEntityUnlabTrafVpi 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.5
VPI value of the VCC supporting unlabeled traffic.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

hh3cMplsLdpEntityUnlabTrafVci 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.6
VCI value of the VCC supporting unlabeled traffic.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

hh3cMplsLdpEntityMergeCapability 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.7
Sets the merge capability for this LDP entity. Current Release of H3CMPLS does not provide support for any kind of Merge.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noMerge(0), vpMerge(1), vcMerge(2), vpVcMerge(3)  

hh3cMplsLdpEntityVcDirectionality 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.8
Sets the VC directionality for this LDP entity.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER bidirectional(1), unidirectional(2)  

hh3cMplsLdpEntityWellKnownDiscoveryPort 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.9
The well known LDP Discovery Port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpEntityMtu 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.10
The maximum transmission unit (MTU) that was configured for this entity.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

hh3cMplsLdpEntityKeepAliveHoldTimer 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.11
The two octet value which is the proposed keep alive hold timer for this LDP Entity.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

hh3cMplsLdpEntityFailedInitSessionThreshold 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.12
When attempting to establish a session with a given Peer, the given LDP Entity should send out a notification when exceeding this threshold. A value of 0 (zero) for this object indicates that the threshold is infinity. In other words, a notification will not be sent if the value of this object is 0 (zero).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpEntityLabelDistributionMethod 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.13
For any given LDP session, the method of label distribution must be specified. Current release of H3CMPLS does not provide support for 'downstreamUnsolicited'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER downstreamOnDemand(1), downstreamUnsolicited(2)  

hh3cMplsLdpEntityLabelAllocationMethod 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.14
For any given LDP session, the method of label allocation must be specified. Label can be allocated in either ordered mode or in the independent mode.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ordered(1), independent(2)  

hh3cMplsLdpEntityHelloHoldTimer 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.15
The two octet value which is the proposed hello hold timer for this LDP Entity.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

hh3cMplsLdpEntityRowStatus 1.3.6.1.4.1.25506.8.12.2.1.2.1.1.16
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hh3cMplsLdpEntityIfTable 1.3.6.1.4.1.25506.8.12.2.1.2.2
This table contains information about the interfaces that are associated with an LDP Entity. There should be atleast one interface associated with each LDP Entity. If the LDP Entity supports 'per interface based label space' label type then, atmost one interface can be associated with the LDP entity. If the LDP Entity supports 'per platform based label space' label type then, more than one interface can be associated with the LDP Entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpEntityIfEntry

hh3cMplsLdpEntityIfEntry 1.3.6.1.4.1.25506.8.12.2.1.2.2.1
An entry in this table represents an Interface that is associated with a LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. An interface (row in this table) can be created/deleted only when the associted LDP Entity row status has the value notInService or notReady.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpEntityIfEntry  

hh3cMplsLdpEntityIfIndex 1.3.6.1.4.1.25506.8.12.2.1.2.2.1.1
Identifier that uniquely identifies the Interface with respect to an LDP Entity. The ifIndex value corresponds to the IfIndex value of the MIB-II
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

hh3cMplsLdpEntityIfIpv4Address 1.3.6.1.4.1.25506.8.12.2.1.2.2.1.2
The IPv4 address associated with the interface.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hh3cMplsLdpEntityIfRowStatus 1.3.6.1.4.1.25506.8.12.2.1.2.2.1.3
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hh3cMplsLdpEntityConfAtmLabelRangeTable 1.3.6.1.4.1.25506.8.12.2.1.2.3
The MPLS LDP Entity Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Entities. LDP Entities which use ATM must have at least one entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpEntityConfAtmLabelRangeEntry

hh3cMplsLdpEntityConfAtmLabelRangeEntry 1.3.6.1.4.1.25506.8.12.2.1.2.3.1
A row in the LDP Entity Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. NOTE: The ranges for a specific LDP Entity are UNIQUE and non-overlapping. For example, for a specific LDP Entity index, there could be one entry having ConfLowerBound vpi/vci == 0/32, and ConfUpperBound vpi/vci == 0/100, and a second entry for this same interface with ConfLowerBound vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200. However, there could not be a third entry with ConfLowerBound vpi/vci == 0/200 and ConfUpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e. both entries now have 0/200). A row will not be created unless a unique and non-overlapping range is specified. Thus, row creation implies a one-shot row creation of LDP EntityID and ConfLowerBound vpi/vci and ConfUpperBound vpi/vci. At least one label range entry for a specific LDP Entity MUST include the default VPI/VCI values denoted in the LDP Entity Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpEntityConfAtmLabelRangeEntry  

hh3cMplsLdpEntityConfAtmLabelRangeLowerBoundVPI 1.3.6.1.4.1.25506.8.12.2.1.2.3.1.1
The minimum VPI number configured for this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

hh3cMplsLdpEntityConfAtmLabelRangeLowerBoundVCI 1.3.6.1.4.1.25506.8.12.2.1.2.3.1.2
The minimum VCI number configured for this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

hh3cMplsLdpEntityConfAtmLabelRangeUpperBoundVPI 1.3.6.1.4.1.25506.8.12.2.1.2.3.1.3
The maximum VPI number configured for this range.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

hh3cMplsLdpEntityConfAtmLabelRangeUpperBoundVCI 1.3.6.1.4.1.25506.8.12.2.1.2.3.1.4
The maximum VCI number configured for this range.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

hh3cMplsLdpEntityConfAtmLabelRangeRowStatus 1.3.6.1.4.1.25506.8.12.2.1.2.3.1.5
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hh3cMplsLdpEntityStatsTable 1.3.6.1.4.1.25506.8.12.2.1.2.4
This table is a read-only table which augments the MplsLdpConfEntityTable. The purpose of this table is to keep statistical information about the LDP Entities on the LSR.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpEntityStatsEntry

hh3cMplsLdpEntityStatsEntry 1.3.6.1.4.1.25506.8.12.2.1.2.4.1
A row in this table contains statistical information about an LDP Entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpEntityStatsEntry  

hh3cMplsLdpAttemptedSessions 1.3.6.1.4.1.25506.8.12.2.1.2.4.1.1
A count of the total attempted sessions for this LDP Entity.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hh3cMplsLdpPeerTable 1.3.6.1.4.1.25506.8.12.2.1.3.1
Information about LDP peers which have been discovered by the LDP Entities that are managed by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpPeerEntry

hh3cMplsLdpPeerEntry 1.3.6.1.4.1.25506.8.12.2.1.3.1.1
Information about a single Peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpPeerEntry  

hh3cMplsLdpPeerIndex 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.1
An identifier for the LDP peer that is unique within the scope of this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

hh3cMplsLdpPeerID 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.2
The LDP identifier of this LDP Peer.
Status: current Access: read-create
OBJECT-TYPE    
  MplsLdpIdentifier  

hh3cMplsLdpPeerInternetworkAddrType 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.3
The type of the internetwork layer address of this LDP peer. This object indicates how the value of hh3cMplsLdpPeerInternetworkAddr is to be interpreted.
Status: current Access: read-create
OBJECT-TYPE    
  AddressFamilyNumbers  

hh3cMplsLdpPeerInternetworkAddr 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.4
The value of the internetwork layer address of this LDP peer.
Status: current Access: read-create
OBJECT-TYPE    
  MplsLdpGenAddr  

hh3cMplsLdpPeerDefaultMtu 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.5
The default maximum transmission unit (MTU) of the LDP Peer.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

hh3cMplsLdpPeerKeepAliveHoldTimer 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.6
The two octet unsigned non zero INTEGER that indicates the number of seconds that this Peer proposes for the value of the KeepAlive Interval.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

hh3cMplsLdpPeerLabelDistributionMethod 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.7
For any given LDP session, the method of label distribution must be specified.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER downstreamOnDemand(1), downstreamUnsolicited(2)  

hh3cMplsLdpPeerType 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.8
Indicates whether a peer is a local peer or a remote peer
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

hh3cMplsLdpPeerRowStatus 1.3.6.1.4.1.25506.8.12.2.1.3.1.1.9
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hh3cMplsLdpPeerConfAtmLabelRangeTable 1.3.6.1.4.1.25506.8.12.2.1.3.2
The MPLS LDP Peer Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Peers. LDP Peers which use ATM must have at least one entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpPeerConfAtmLabelRangeEntry

hh3cMplsLdpPeerConfAtmLabelRangeEntry 1.3.6.1.4.1.25506.8.12.2.1.3.2.1
A row in the LDP Peer Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. NOTE: The ranges for a specific LDP Peer are UNIQUE and non-overlapping. For example, for a specific LDP Peer index, there could be one entry having ConfLowerBound vpi/vci == 0/32, and ConfUpperBound vpi/vci == 0/100, and a second entry for this same interface with ConfLowerBound vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200. However, there could not be a third entry with ConfLowerBound vpi/vci == 0/200 and ConfUpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e. both entries now have 0/200). A row will not be created unless a unique and non-overlapping range is specified. Thus, row creation implies a one-shot row creation of LDP PeerIndex and ConfLowerBound vpi/vci and ConfUpperBound vpi/vci. At least one label range entry for a specific LDP Peer MUST include the default VPI/VCI values denoted in the LDP Peer Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpPeerConfAtmLabelRangeEntry  

hh3cMplsLdpPeerConfAtmLabelRangeLowerBoundVPI 1.3.6.1.4.1.25506.8.12.2.1.3.2.1.1
The minimum VPI number configured for this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

hh3cMplsLdpPeerConfAtmLabelRangeLowerBoundVCI 1.3.6.1.4.1.25506.8.12.2.1.3.2.1.2
The minimum VCI number configured for this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

hh3cMplsLdpPeerConfAtmLabelRangeUpperBoundVPI 1.3.6.1.4.1.25506.8.12.2.1.3.2.1.3
The maximum VPI number configured for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

hh3cMplsLdpPeerConfAtmLabelRangeUpperBoundVCI 1.3.6.1.4.1.25506.8.12.2.1.3.2.1.4
The maximum VCI number configured for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

hh3cMplsLdpSessionTable 1.3.6.1.4.1.25506.8.12.2.1.4.1
A table of Sessions between the LDP Entities and LDP Peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpSessionEntry

hh3cMplsLdpSessionEntry 1.3.6.1.4.1.25506.8.12.2.1.4.1.1
An entry in this table represents information on a single session between an LDP Entity and LDP Peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpSessionEntry  

hh3cMplsLdpSessionIndex 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.1
An unique identifier for this entry such that it identifies a specific LDP Session.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

hh3cMplsLdpSessionID 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.2
The LDP Session identifier.
Status: current Access: read-only
OBJECT-TYPE    
  MplsLdpIdentifier  

hh3cMplsLdpSessionProtocolVersion 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.3
The version of the LDP Protocol which this session is using.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

hh3cMplsLdpSessionKeepAliveHoldTimeRemaining 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.4
The keep alive hold time remaining for this session.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

hh3cMplsLdpSessionRole 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.5
An indication of whether the LDP Entity associated with this session is acting in an 'active' role or a 'passive' role.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

hh3cMplsLdpSessionState 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.6
The current state of the session, all of the states 1 - 5 are based on the state machine for session negotiation behavior.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonexistent(1), initialized(2), openrec(3), opensent(4), operational(5)  

hh3cMplsLdpSessionAtmLabelRangeLowerBoundVPI 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.7
The minimum VPI number for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

hh3cMplsLdpSessionAtmLabelRangeLowerBoundVCI 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.8
The minimum VCI number for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

hh3cMplsLdpSessionAtmLabelRangeUpperBoundVPI 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.9
The maximum VPI number for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

hh3cMplsLdpSessionAtmLabelRangeUpperBoundVCI 1.3.6.1.4.1.25506.8.12.2.1.4.1.1.10
The maximum VCI number for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

hh3cMplsLdpHelloAdjacencyTable 1.3.6.1.4.1.25506.8.12.2.1.5.1
A table of Hello Adjacencies for Sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpHelloAdjacencyEntry

hh3cMplsLdpHelloAdjacencyEntry 1.3.6.1.4.1.25506.8.12.2.1.5.1.1
Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpHelloAdjacencyEntry  

hh3cMplsLdpHelloAdjacencyIndex 1.3.6.1.4.1.25506.8.12.2.1.5.1.1.1
An identifier for the adjacency.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

hh3cMplsLdpHelloAdjacencyHoldTimeRemaining 1.3.6.1.4.1.25506.8.12.2.1.5.1.1.2
The time remaining for this Hello Adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

hh3cMplsLdpCrlspTnlTable 1.3.6.1.4.1.25506.8.12.2.1.6.1
The hh3cMplsLdpCrlspTnlTable allows new CRLSP MPLS tunnels to be created. The ER hops associated with a CRLSP tunnel are to be configured using the hh3cMplsLdpCrlspErHopTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpCrlspTnlEntry

hh3cMplsLdpCrlspTnlEntry 1.3.6.1.4.1.25506.8.12.2.1.6.1.1
An entry in this table represents an CRLSP MPLS tunnel. An entry can be created by a network administrator.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpCrlspTnlEntry  

hh3cMplsLdpCrlspTnlIndex 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.1
Uniquely identifies this row.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MplsTunnelIndex  

hh3cMplsLdpCrlspTnlName 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.2
The 'canonical' name assigned to the tunnel that can be used to refer to it on the 'console' port.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

hh3cMplsLdpCrlspTnlDirection 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.3
Whether this tunnel is unidirectional-incoming, unidirectional-outgoing, or bidirectional.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER in(1), out(2), inOut(3)  

hh3cMplsLdpCrlspTnlSignallingProto 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.4
The signaling protocol, if any, that set up this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), ldp(2), rsvp(3)  

hh3cMplsLdpCrlspTnlSetupPrio 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.5
The setup priority of this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

hh3cMplsLdpCrlspTnlHoldingPrio 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.6
The holding priority for this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

hh3cMplsLdpCrlspTnlPeakDataRate 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.7
The peak rate - the maximum rate at which traffic will be sent on the CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BitRate  

hh3cMplsLdpCrlspTnlPeakBurstSize 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.8
The peak burst size - the maximum burst size of the traffic that can occur in the established CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BurstSize  

hh3cMplsLdpCrlspTnlCommittedDataRate 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.9
The committed rate - the committed rate at which traffic will be sent on the CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BitRate  

hh3cMplsLdpCrlspTnlCommittedBurstSize 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.10
The committed burst size - the committed burst size of the traffic that will be handled in the established CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BurstSize  

hh3cMplsLdpCrlspTnlExcessBurstSize 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.11
The Excess burst size - the excess burst size limit to be used for traffic conditioning at the ingress of the CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BurstSize  

hh3cMplsLdpCrlspTnlIsPinned 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.12
Indicates whether the loose-routed hops of this tunnel are to be pinned.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hh3cMplsLdpCrlspTnlFrequency 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.13
Indicates the frequency of usage of the established CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..2  

hh3cMplsLdpCrlspTnlWeight 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.14
Indicates the weight that is the established CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

hh3cMplsLdpCrlspTnlRowStatus 1.3.6.1.4.1.25506.8.12.2.1.6.1.1.15
For controlling the state of this row. The status can be set to 'active' only when atleast one ERHOP is created in the hh3cMplsLdpErHopTable, associated with this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hh3cMplsLdpCrlspErHopTable 1.3.6.1.4.1.25506.8.12.2.1.6.2
The hh3cMplsLdpCrlspErHopTable is used to indicate the hops, strict or loose, for an MPLS CRLSP tunnel defined in hh3cMplsLdpCrlspTnlTable. There must be atleast one entry in this table for each CRLSP tunnel that is supported in the hh3cMplsLdpCrlspTnlTable. The first row in the table is the first hop after the origination point of the tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cMplsLdpCrlspErHopEntry

hh3cMplsLdpCrlspErHopEntry 1.3.6.1.4.1.25506.8.12.2.1.6.2.1
An entry in this table represents a tunnel hop. An entry is created by a network administrator for signalled ERLSP set up by LDP or RSVP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hh3cMplsLdpCrlspErHopEntry  

hh3cMplsLdpCrlspErHopIndex 1.3.6.1.4.1.25506.8.12.2.1.6.2.1.1
Secondary index into this table identifying the particular hop.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

hh3cMplsLdpCrlspErHopAddrType 1.3.6.1.4.1.25506.8.12.2.1.6.2.1.2
Address type of this hop.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ipV4(1)  

hh3cMplsLdpCrlspErHopIpv4Addr 1.3.6.1.4.1.25506.8.12.2.1.6.2.1.3
If hh3cMplsLdpCrlspErHopAddrType is ipV4(1), IPv4 address of this hop. This object is not significant otherwise and should return a value of 0.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hh3cMplsLdpCrlspErHopIpv4PrefixLen 1.3.6.1.4.1.25506.8.12.2.1.6.2.1.4
If hh3cMplsLdpCrlspErHopAddrType is ipV4(1), prefix length for this hop's IPv4 address. This object is not significant otherwise and should return a value of 0.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..32  

hh3cMplsLdpCrlspErHopStrictOrLoose 1.3.6.1.4.1.25506.8.12.2.1.6.2.1.5
Whether this is a strict or loose hop.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER strict(1), loose(2)  

hh3cMplsLdpCrlspErHopRowStatus 1.3.6.1.4.1.25506.8.12.2.1.6.2.1.6
For creating, modifying and deleting this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hh3cMplsLdpNotificationPrefix 1.3.6.1.4.1.25506.8.12.2.2.0
OBJECT IDENTIFIER    

hh3cMplsLdpFailedInitSessionThresholdExceeded 1.3.6.1.4.1.25506.8.12.2.2.0.1
This notification is generated whenever the value of hh3cMplsLdpEntityFailedInitSessionThreshold is exceeded.
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpCrlspTunnelUp 1.3.6.1.4.1.25506.8.12.2.2.0.2
This notification is generated by the Ingress LSR of the CRLSP tunnel on the receipt of Label mapping message from the downstream LSR for the LAbel request sent for the CRLSP tunnel.
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpCrlspTunnelDown 1.3.6.1.4.1.25506.8.12.2.2.0.3
This notification is generated when a CRLSP Row status is modified to destroy the CRLSP tunnel. - due to pre-emption etc.,
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpCrlspTunnelSetupFailure 1.3.6.1.4.1.25506.8.12.2.2.0.4
This notification is generated by the Ingress LSR of the CRLSP tunnel on the receipt of Nak message from the downstream LSR for the Label request sent for the CRLSP tunnel. This can occur due to improper ER hop values being set, or Traffic resources not available etc.,
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpIncarnUpEventFailure 1.3.6.1.4.1.25506.8.12.2.2.0.11
This notification is generated by LDP to notify the Incarnation UP Event failure
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpIncarnDownEventFailure 1.3.6.1.4.1.25506.8.12.2.2.0.12
This notification is generated by LDP to notify the Incarnation DOWN Event failure
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpEntityUpEventFailure 1.3.6.1.4.1.25506.8.12.2.2.0.13
This notification is generated by LDP to notify the ENTITY UP Event failure
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpEntityDownEventFailure 1.3.6.1.4.1.25506.8.12.2.2.0.14
This notification is generated by LDP to notify the ENTITY DOWN Event failure
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpSessionUpEventFailure 1.3.6.1.4.1.25506.8.12.2.2.0.15
Generation of this trap occurs when the value of 'hh3cMplsLdpSessionState' enters the 'operational(5)' state.
Status: current Access: read-create
NOTIFICATION-TYPE    

hh3cMplsLdpSessionDownEventFailure 1.3.6.1.4.1.25506.8.12.2.2.0.16
Generation of this trap occurs when the value of 'hh3cMplsLdpSessionState' leaves the 'operational(5)' state.
Status: current Access: read-create
NOTIFICATION-TYPE