HC-RMON-MIB

File: HC-RMON-MIB.mib (118311 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
RMON-MIB RMON2-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Integer32 Gauge32 Counter64
TEXTUAL-CONVENTION RowStatus MODULE-COMPLIANCE
OBJECT-GROUP rmon OwnerString
statistics history hosts
hostTopN matrix etherStatsIndex
etherHistoryIndex etherHistorySampleIndex hostIndex
hostAddress hostTimeIndex hostTimeCreationOrder
hostTopNControlEntry hostTopNReport hostTopNIndex
matrixSDIndex matrixSDSourceAddress matrixSDDestAddress
matrixDSIndex matrixDSDestAddress matrixDSSourceAddress
capture captureBufferControlIndex captureBufferIndex
protocolDirLocalIndex protocolDistControlIndex protocolDist
hlHostControlIndex nlHost nlHostTimeMark
nlHostAddress hlMatrixControlIndex nlMatrix
nlMatrixSDTimeMark nlMatrixSDSourceAddress nlMatrixSDDestAddress
nlMatrixDSTimeMark nlMatrixDSDestAddress nlMatrixDSSourceAddress
nlMatrixTopNControlEntry nlMatrixTopNControlIndex nlMatrixTopNIndex
alHost alHostTimeMark alMatrix
alMatrixSDTimeMark alMatrixDSTimeMark alMatrixTopNControlEntry
alMatrixTopNControlIndex alMatrixTopNIndex usrHistory
usrHistoryControlIndex usrHistorySampleIndex usrHistoryObjectIndex
rmonConformance ZeroBasedCounter32 probeConfig

Defined Types

ZeroBasedCounter64  
This TC describes an object which counts events with the following semantics: objects of this type will be set to zero(0) on creation and will thereafter count appropriate events, wrapping back to zero(0) when the value 2^64 is reached. Provided that an application discovers the new object within the minimum time to wrap it can use the initial value as a delta since it last polled the table of which this object is part. It is important for a management station to be aware of this minimum time and the actual time between polls, and to discard data if the actual time is too long or there is no defined minimum time. Typically this TC is used in tables where the INDEX space is constantly changing and/or the TimeFilter mechanism is in use.
TEXTUAL-CONVENTION    
  Counter64  

RmonGauge64  
The RmonGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value. The maximum value can not be greater than 2^64-1. The value of a Gauge has its maximum value whenever the information being modeled is greater or equal to that maximum value; if the information being modeled subsequently decreases below the maximum value, the Gauge also decreases.
TEXTUAL-CONVENTION    
  Counter64  

MediaIndependentEntry  
SEQUENCE    
  mediaIndependentIndex INTEGER 1..65535
  mediaIndependentDataSource OBJECT IDENTIFIER
  mediaIndependentDropEvents Counter32
  mediaIndependentDroppedFrames Counter32
  mediaIndependentInPkts Counter32
  mediaIndependentInOverflowPkts Counter32
  mediaIndependentInHighCapacityPkts Counter64
  mediaIndependentOutPkts Counter32
  mediaIndependentOutOverflowPkts Counter32
  mediaIndependentOutHighCapacityPkts Counter64
  mediaIndependentInOctets Counter32
  mediaIndependentInOverflowOctets Counter32
  mediaIndependentInHighCapacityOctets Counter64
  mediaIndependentOutOctets Counter32
  mediaIndependentOutOverflowOctets Counter32
  mediaIndependentOutHighCapacityOctets Counter64
  mediaIndependentInNUCastPkts Counter32
  mediaIndependentInNUCastOverflowPkts Counter32
  mediaIndependentInNUCastHighCapacityPkts Counter64
  mediaIndependentOutNUCastPkts Counter32
  mediaIndependentOutNUCastOverflowPkts Counter32
  mediaIndependentOutNUCastHighCapacityPkts Counter64
  mediaIndependentInErrors Counter32
  mediaIndependentOutErrors Counter32
  mediaIndependentInputSpeed Gauge32
  mediaIndependentOutputSpeed Gauge32
  mediaIndependentOwner OwnerString
  mediaIndependentStatus RowStatus

EtherStatsHighCapacityEntry  
SEQUENCE    
  etherStatsHighCapacityOverflowPkts Counter32
  etherStatsHighCapacityPkts Counter64
  etherStatsHighCapacityOverflowOctets Counter32
  etherStatsHighCapacityOctets Counter64
  etherStatsHighCapacityOverflowPkts64Octets Counter32
  etherStatsHighCapacityPkts64Octets Counter64
  etherStatsHighCapacityOverflowPkts65to127Octets Counter32
  etherStatsHighCapacityPkts65to127Octets Counter64
  etherStatsHighCapacityOverflowPkts128to255Octets Counter32
  etherStatsHighCapacityPkts128to255Octets Counter64
  etherStatsHighCapacityOverflowPkts256to511Octets Counter32
  etherStatsHighCapacityPkts256to511Octets Counter64
  etherStatsHighCapacityOverflowPkts512to1023Octets Counter32
  etherStatsHighCapacityPkts512to1023Octets Counter64
  etherStatsHighCapacityOverflowPkts1024to1518Octets Counter32
  etherStatsHighCapacityPkts1024to1518Octets Counter64

EtherHistoryHighCapacityEntry  
SEQUENCE    
  etherHistoryHighCapacityOverflowPkts Gauge32
  etherHistoryHighCapacityPkts RmonGauge64
  etherHistoryHighCapacityOverflowOctets Gauge32
  etherHistoryHighCapacityOctets RmonGauge64

HostHighCapacityEntry  
SEQUENCE    
  hostHighCapacityInOverflowPkts Counter32
  hostHighCapacityInPkts Counter64
  hostHighCapacityOutOverflowPkts Counter32
  hostHighCapacityOutPkts Counter64
  hostHighCapacityInOverflowOctets Counter32
  hostHighCapacityInOctets Counter64
  hostHighCapacityOutOverflowOctets Counter32
  hostHighCapacityOutOctets Counter64

HostTimeHighCapacityEntry  
SEQUENCE    
  hostTimeHighCapacityInOverflowPkts Counter32
  hostTimeHighCapacityInPkts Counter64
  hostTimeHighCapacityOutOverflowPkts Counter32
  hostTimeHighCapacityOutPkts Counter64
  hostTimeHighCapacityInOverflowOctets Counter32
  hostTimeHighCapacityInOctets Counter64
  hostTimeHighCapacityOutOverflowOctets Counter32
  hostTimeHighCapacityOutOctets Counter64

HostTopNHighCapacityEntry  
SEQUENCE    
  hostTopNHighCapacityBaseRate Gauge32
  hostTopNHighCapacityOverflowRate Gauge32
  hostTopNHighCapacityRate RmonGauge64

MatrixSDHighCapacityEntry  
SEQUENCE    
  matrixSDHighCapacityOverflowPkts Counter32
  matrixSDHighCapacityPkts Counter64
  matrixSDHighCapacityOverflowOctets Counter32
  matrixSDHighCapacityOctets Counter64

MatrixDSHighCapacityEntry  
SEQUENCE    
  matrixDSHighCapacityOverflowPkts Counter32
  matrixDSHighCapacityPkts Counter64
  matrixDSHighCapacityOverflowOctets Counter32
  matrixDSHighCapacityOctets Counter64

CaptureBufferHighCapacityEntry  
SEQUENCE    
  captureBufferPacketHighCapacityTime Integer32

ProtocolDistStatsHighCapacityEntry  
SEQUENCE    
  protocolDistStatsHighCapacityOverflowPkts ZeroBasedCounter32
  protocolDistStatsHighCapacityPkts ZeroBasedCounter64
  protocolDistStatsHighCapacityOverflowOctets ZeroBasedCounter32
  protocolDistStatsHighCapacityOctets ZeroBasedCounter64

NlHostHighCapacityEntry  
SEQUENCE    
  nlHostHighCapacityInOverflowPkts ZeroBasedCounter32
  nlHostHighCapacityInPkts ZeroBasedCounter64
  nlHostHighCapacityOutOverflowPkts ZeroBasedCounter32
  nlHostHighCapacityOutPkts ZeroBasedCounter64
  nlHostHighCapacityInOverflowOctets ZeroBasedCounter32
  nlHostHighCapacityInOctets ZeroBasedCounter64
  nlHostHighCapacityOutOverflowOctets ZeroBasedCounter32
  nlHostHighCapacityOutOctets ZeroBasedCounter64

NlMatrixSDHighCapacityEntry  
SEQUENCE    
  nlMatrixSDHighCapacityOverflowPkts ZeroBasedCounter32
  nlMatrixSDHighCapacityPkts ZeroBasedCounter64
  nlMatrixSDHighCapacityOverflowOctets ZeroBasedCounter32
  nlMatrixSDHighCapacityOctets ZeroBasedCounter64

NlMatrixDSHighCapacityEntry  
SEQUENCE    
  nlMatrixDSHighCapacityOverflowPkts ZeroBasedCounter32
  nlMatrixDSHighCapacityPkts ZeroBasedCounter64
  nlMatrixDSHighCapacityOverflowOctets ZeroBasedCounter32
  nlMatrixDSHighCapacityOctets ZeroBasedCounter64

NlMatrixTopNHighCapacityEntry  
SEQUENCE    
  nlMatrixTopNHighCapacityBasePktRate Gauge32
  nlMatrixTopNHighCapacityOverflowPktRate Gauge32
  nlMatrixTopNHighCapacityPktRate RmonGauge64
  nlMatrixTopNHighCapacityReverseBasePktRate Gauge32
  nlMatrixTopNHighCapacityReverseOverflowPktRate Gauge32
  nlMatrixTopNHighCapacityReversePktRate RmonGauge64
  nlMatrixTopNHighCapacityBaseOctetRate Gauge32
  nlMatrixTopNHighCapacityOverflowOctetRate Gauge32
  nlMatrixTopNHighCapacityOctetRate RmonGauge64
  nlMatrixTopNHighCapacityReverseBaseOctetRate Gauge32
  nlMatrixTopNHighCapacityReverseOverflowOctetRate Gauge32
  nlMatrixTopNHighCapacityReverseOctetRate RmonGauge64

AlHostHighCapacityEntry  
SEQUENCE    
  alHostHighCapacityInOverflowPkts ZeroBasedCounter32
  alHostHighCapacityInPkts ZeroBasedCounter64
  alHostHighCapacityOutOverflowPkts ZeroBasedCounter32
  alHostHighCapacityOutPkts ZeroBasedCounter64
  alHostHighCapacityInOverflowOctets ZeroBasedCounter32
  alHostHighCapacityInOctets ZeroBasedCounter64
  alHostHighCapacityOutOverflowOctets ZeroBasedCounter32
  alHostHighCapacityOutOctets ZeroBasedCounter64

AlMatrixSDHighCapacityEntry  
SEQUENCE    
  alMatrixSDHighCapacityOverflowPkts ZeroBasedCounter32
  alMatrixSDHighCapacityPkts ZeroBasedCounter64
  alMatrixSDHighCapacityOverflowOctets ZeroBasedCounter32
  alMatrixSDHighCapacityOctets ZeroBasedCounter64

AlMatrixDSHighCapacityEntry  
SEQUENCE    
  alMatrixDSHighCapacityOverflowPkts ZeroBasedCounter32
  alMatrixDSHighCapacityPkts ZeroBasedCounter64
  alMatrixDSHighCapacityOverflowOctets ZeroBasedCounter32
  alMatrixDSHighCapacityOctets ZeroBasedCounter64

AlMatrixTopNHighCapacityEntry  
SEQUENCE    
  alMatrixTopNHighCapacityBasePktRate Gauge32
  alMatrixTopNHighCapacityOverflowPktRate Gauge32
  alMatrixTopNHighCapacityPktRate RmonGauge64
  alMatrixTopNHighCapacityReverseBasePktRate Gauge32
  alMatrixTopNHighCapacityReverseOverflowPktRate Gauge32
  alMatrixTopNHighCapacityReversePktRate RmonGauge64
  alMatrixTopNHighCapacityBaseOctetRate Gauge32
  alMatrixTopNHighCapacityOverflowOctetRate Gauge32
  alMatrixTopNHighCapacityOctetRate RmonGauge64
  alMatrixTopNHighCapacityReverseBaseOctetRate Gauge32
  alMatrixTopNHighCapacityReverseOverflowOctetRate Gauge32
  alMatrixTopNHighCapacityReverseOctetRate RmonGauge64

UsrHistoryHighCapacityEntry  
SEQUENCE    
  usrHistoryHighCapacityOverflowAbsValue Gauge32
  usrHistoryHighCapacityAbsValue RmonGauge64

Defined Values

hcRMON 1.3.6.1.2.1.16.20.8
The MIB module for managing remote monitoring device implementations. This MIB module augments the original RMON MIB as specified in RFC 1757 and RFC 1513 and RMON2 MIB as specified in RFC 2021.
MODULE-IDENTITY    

mediaIndependentStats 1.3.6.1.2.1.16.21
OBJECT IDENTIFIER    

mediaIndependentTable 1.3.6.1.2.1.16.21.1
Media independent statistics for promiscious monitoring of any media. The following table defines media independent statistics that provides information for full and/or half-duplex links as well as high capacity links. For half-duplex links, the mediaIndependentOut* objects will not be present. For full-duplex links, the mediaIndependentOut* objects will be present. Whenever possible, the probe should count packets moving away from the closest terminating equipment as output packets. Failing that, the probe should count packets moving away from the DTE as output packets.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MediaIndependentEntry

mediaIndependentEntry 1.3.6.1.2.1.16.21.1.1
Media independent statistics for promiscious monitoring of any media.
Status: current Access: not-accessible
OBJECT-TYPE    
  MediaIndependentEntry  

mediaIndependentIndex 1.3.6.1.2.1.16.21.1.1.1
The value of this object uniquely identifies this mediaIndependent entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

mediaIndependentDataSource 1.3.6.1.2.1.16.21.1.1.2
This object identifies the source of the data that this mediaIndependent entry is configured to analyze. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573 [4,6], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated mediaIndependentStatus object is equal to valid(1).
Status: current Access: read-create
OBJECT-TYPE    
  OBJECT IDENTIFIER  

mediaIndependentDropEvents 1.3.6.1.2.1.16.21.1.1.3
The total number of events in which packets were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentDroppedFrames 1.3.6.1.2.1.16.21.1.1.4
The total number of frames which were received by the probe and therefore not accounted for in the mediaIndependentDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentInPkts 1.3.6.1.2.1.16.21.1.1.5
The total number of packets (including bad packets, broadcast packets, and multicast packets) received on a half-duplex link or on the inbound connection of a full-duplex link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentInOverflowPkts 1.3.6.1.2.1.16.21.1.1.6
The number of times the associated mediaIndependentInPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentInHighCapacityPkts 1.3.6.1.2.1.16.21.1.1.7
The total number of packets (including bad packets, broadcast packets, and multicast packets) received on a half-duplex link or on the inbound connection of a full-duplex link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

mediaIndependentOutPkts 1.3.6.1.2.1.16.21.1.1.8
The total number of packets (including bad packets, broadcast packets, and multicast packets) received on a full-duplex link in the direction of the network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentOutOverflowPkts 1.3.6.1.2.1.16.21.1.1.9
The number of times the associated mediaIndependentOutPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentOutHighCapacityPkts 1.3.6.1.2.1.16.21.1.1.10
The total number of packets (including bad packets, broadcast packets, and multicast packets) received on a full-duplex link in the direction of the network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

mediaIndependentInOctets 1.3.6.1.2.1.16.21.1.1.11
The total number of octets of data (including those in bad packets) received (excluding framing bits but including FCS octets) on a half-duplex link or on the inbound connection of a full-duplex link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentInOverflowOctets 1.3.6.1.2.1.16.21.1.1.12
The number of times the associated mediaIndependentInOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentInHighCapacityOctets 1.3.6.1.2.1.16.21.1.1.13
The total number of octets of data (including those in bad packets) received (excluding framing bits but including FCS octets) on a half-duplex link or on the inbound connection of a full-duplex link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

mediaIndependentOutOctets 1.3.6.1.2.1.16.21.1.1.14
The total number of octets of data (including those in bad packets) received on a full-duplex link in the direction of the network (excluding framing bits but including FCS octets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentOutOverflowOctets 1.3.6.1.2.1.16.21.1.1.15
The number of times the associated mediaIndependentOutOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentOutHighCapacityOctets 1.3.6.1.2.1.16.21.1.1.16
The total number of packets (including bad packets, broadcast packets, and multicast packets) received on a full-duplex link in the direction of the network (excluding framing bits but including FCS octets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

mediaIndependentInNUCastPkts 1.3.6.1.2.1.16.21.1.1.17
The total number of non-unicast packets (including bad packets) received on a half-duplex link or on the inbound connection of a full-duplex link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentInNUCastOverflowPkts 1.3.6.1.2.1.16.21.1.1.18
The number of times the associated mediaIndependentInNUCastPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentInNUCastHighCapacityPkts 1.3.6.1.2.1.16.21.1.1.19
The total number of non-unicast packets (including bad packets) received on a half-duplex link or on the inbound connection of a full-duplex link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

mediaIndependentOutNUCastPkts 1.3.6.1.2.1.16.21.1.1.20
The total number of non-unicast packets (including bad packets) received on a full-duplex link in the direction of the network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentOutNUCastOverflowPkts 1.3.6.1.2.1.16.21.1.1.21
The number of times the associated mediaIndependentOutNUCastPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentOutNUCastHighCapacityPkts 1.3.6.1.2.1.16.21.1.1.22
The total number of packets (including bad packets) received on a full-duplex link in the direction of the network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

mediaIndependentInErrors 1.3.6.1.2.1.16.21.1.1.23
The total number of bad packets received on a half-duplex link or on the inbound connection of a full-duplex link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentOutErrors 1.3.6.1.2.1.16.21.1.1.24
The total number of bad packets received on a full-duplex link in the direction of the network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mediaIndependentInputSpeed 1.3.6.1.2.1.16.21.1.1.25
The nominal maximum speed in kilobits per second of this half-duplex link or on the inbound connection of this full-duplex link. If the speed is unknown or there is no fixed maximum (e.g. a compressed link), this value shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

mediaIndependentOutputSpeed 1.3.6.1.2.1.16.21.1.1.26
The nominal maximum speed in kilobits per second of this full-duplex link in the direction of the network. If the speed is unknown or there is no fixed maximum (e.g. a compressed link), this value shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

mediaIndependentOwner 1.3.6.1.2.1.16.21.1.1.27
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current Access: read-create
OBJECT-TYPE    
  OwnerString  

mediaIndependentStatus 1.3.6.1.2.1.16.21.1.1.28
The status of this media independent statistics entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

etherStatsHighCapacityTable 1.3.6.1.2.1.16.1.7
Contains the High Capacity RMON extensions to the RMON-1 etherStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtherStatsHighCapacityEntry

etherStatsHighCapacityEntry 1.3.6.1.2.1.16.1.7.1
Contains the High Capacity RMON extensions to the RMON-1 etherStatsEntry. These objects will be created by the agent for all etherStatsEntries it deems appropriate.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtherStatsHighCapacityEntry  

etherStatsHighCapacityOverflowPkts 1.3.6.1.2.1.16.1.7.1.1
The number of times the associated etherStatsPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

etherStatsHighCapacityPkts 1.3.6.1.2.1.16.1.7.1.2
The total number of packets (including bad packets, broadcast packets, and multicast packets) received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

etherStatsHighCapacityOverflowOctets 1.3.6.1.2.1.16.1.7.1.3
The number of times the associated etherStatsOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

etherStatsHighCapacityOctets 1.3.6.1.2.1.16.1.7.1.4
The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets). If the network is half-duplex Fast Ethernet, this object can be used as a reasonable estimate of utilization. If greater precision is desired, the etherStatsHighCapacityPkts and etherStatsHighCapacityOctets objects should be sampled before and after a common interval. The differences in the sampled values are Pkts and Octets, respectively, and the number of seconds in the interval is Interval. These values are used to calculate the Utilization as follows: Pkts * (.96 + .64) + (Octets * .08) Utilization = ------------------------------------- Interval * 10,000 The result of this equation is the value Utilization which is the percent utilization of the ethernet segment on a scale of 0 to 100 percent. This table is not appropriate for monitoring full-duplex ethernets. If the network is a full-duplex ethernet and the mediaIndependentTable is monitoring that network, the utilization can be calculated as follows: 1) Determine the utilization of the inbound path by using the appropriate equation (for ethernet or fast ethernet) to determine the utilization, substituting mediaIndependentInPkts for etherStatsHighCapacityPkts, and mediaIndependentInOctets for etherStatsHighCapacityOctets. Call the resulting utilization inUtilization. 2) Determine the utilization of the outbound path by using the same equation to determine the utilization, substituting mediaIndependentOutPkts for etherStatsHighCapacityPkts, and mediaIndependentOutOctetss for etherStatsHighCapacityOctets. Call the resulting utilization outUtilization. 3) The utilization is the maximum of inUtilization and outUtilization. This metric shows the amount of percentage of bandwidth that is left before congestion will be experienced on the link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

etherStatsHighCapacityOverflowPkts64Octets 1.3.6.1.2.1.16.1.7.1.5
The number of times the associated etherStatsPkts64Octets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

etherStatsHighCapacityPkts64Octets 1.3.6.1.2.1.16.1.7.1.6
The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

etherStatsHighCapacityOverflowPkts65to127Octets 1.3.6.1.2.1.16.1.7.1.7
The number of times the associated etherStatsPkts65to127Octets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

etherStatsHighCapacityPkts65to127Octets 1.3.6.1.2.1.16.1.7.1.8
The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

etherStatsHighCapacityOverflowPkts128to255Octets 1.3.6.1.2.1.16.1.7.1.9
The number of times the associated etherStatsPkts128to255Octets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

etherStatsHighCapacityPkts128to255Octets 1.3.6.1.2.1.16.1.7.1.10
The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

etherStatsHighCapacityOverflowPkts256to511Octets 1.3.6.1.2.1.16.1.7.1.11
The number of times the associated etherStatsPkts256to511Octets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

etherStatsHighCapacityPkts256to511Octets 1.3.6.1.2.1.16.1.7.1.12
The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

etherStatsHighCapacityOverflowPkts512to1023Octets 1.3.6.1.2.1.16.1.7.1.13
The number of times the associated etherStatsPkts512to1023Octets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

etherStatsHighCapacityPkts512to1023Octets 1.3.6.1.2.1.16.1.7.1.14
The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

etherStatsHighCapacityOverflowPkts1024to1518Octets 1.3.6.1.2.1.16.1.7.1.15
The number of times the associated etherStatsPkts1024to1518Octets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

etherStatsHighCapacityPkts1024to1518Octets 1.3.6.1.2.1.16.1.7.1.16
The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

etherHistoryHighCapacityTable 1.3.6.1.2.1.16.2.6
Contains the High Capacity RMON extensions to the RMON-1 etherHistoryTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtherHistoryHighCapacityEntry

etherHistoryHighCapacityEntry 1.3.6.1.2.1.16.2.6.1
Contains the High Capacity RMON extensions to the RMON-1 etherHistoryEntry. These objects will be created by the agent for all etherHistoryEntries associated with whichever historyControlEntries it deems appropriate. (i.e., either all etherHistoryHighCapacityEntries associated with a particular historyControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  EtherHistoryHighCapacityEntry  

etherHistoryHighCapacityOverflowPkts 1.3.6.1.2.1.16.2.6.1.1
The number of times the associated etherHistoryPkts Gauge overflowed during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etherHistoryHighCapacityPkts 1.3.6.1.2.1.16.2.6.1.2
The total number of packets (including bad packets, broadcast packets, and multicast packets) received during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

etherHistoryHighCapacityOverflowOctets 1.3.6.1.2.1.16.2.6.1.3
The number of times the associated etherHistoryOctets counter has overflowed during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etherHistoryHighCapacityOctets 1.3.6.1.2.1.16.2.6.1.4
The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets) during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

hostHighCapacityTable 1.3.6.1.2.1.16.4.5
Contains the High Capacity RMON extensions to the RMON-1 hostTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HostHighCapacityEntry

hostHighCapacityEntry 1.3.6.1.2.1.16.4.5.1
Contains the High Capacity RMON extensions to the RMON-1 hostEntry. These objects will be created by the agent for all hostEntries associated with whichever hostControlEntries it deems appropriate. (i.e., either all hostHighCapacityEntries associated with a particular hostControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  HostHighCapacityEntry  

hostHighCapacityInOverflowPkts 1.3.6.1.2.1.16.4.5.1.1
The number of times the associated hostInPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hostHighCapacityInPkts 1.3.6.1.2.1.16.4.5.1.2
The number of good packets transmitted to this address since it was added to the hostHighCapacityTable.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hostHighCapacityOutOverflowPkts 1.3.6.1.2.1.16.4.5.1.3
The number of times the associated hostOutPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hostHighCapacityOutPkts 1.3.6.1.2.1.16.4.5.1.4
The number of packets, including bad packets, transmitted by this address since it was added to the hostHighCapacityTable.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hostHighCapacityInOverflowOctets 1.3.6.1.2.1.16.4.5.1.5
The number of times the associated hostInOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hostHighCapacityInOctets 1.3.6.1.2.1.16.4.5.1.6
The number of octets transmitted to this address since it was added to the hostHighCapacityTable (excluding framing bits but including FCS octets), except for those octets in bad packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hostHighCapacityOutOverflowOctets 1.3.6.1.2.1.16.4.5.1.7
The number of times the associated hostOutOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hostHighCapacityOutOctets 1.3.6.1.2.1.16.4.5.1.8
The number of octets transmitted by this address since it was added to the hostHighCapacityTable (excluding framing bits but including FCS octets), including those octets in bad packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hostTimeHighCapacityTable 1.3.6.1.2.1.16.4.6
Contains the High Capacity RMON extensions to the RMON-1 hostTimeTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HostTimeHighCapacityEntry

hostTimeHighCapacityEntry 1.3.6.1.2.1.16.4.6.1
Contains the High Capacity RMON extensions to the RMON-1 hostTimeEntry. These objects will be created by the agent for all hostTimeEntries associated with whichever hostControlEntries it deems appropriate. (i.e., either all hostTimeHighCapacityEntries associated with a particular hostControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  HostTimeHighCapacityEntry  

hostTimeHighCapacityInOverflowPkts 1.3.6.1.2.1.16.4.6.1.1
The number of times the associated hostTimeInPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hostTimeHighCapacityInPkts 1.3.6.1.2.1.16.4.6.1.2
The number of good packets transmitted to this address since it was added to the hostTimeHighCapacityTable.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hostTimeHighCapacityOutOverflowPkts 1.3.6.1.2.1.16.4.6.1.3
The number of times the associated hostTimeOutPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hostTimeHighCapacityOutPkts 1.3.6.1.2.1.16.4.6.1.4
The number of packets, including bad packets, transmitted by this address since it was added to the hostTimeHighCapacityTable.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hostTimeHighCapacityInOverflowOctets 1.3.6.1.2.1.16.4.6.1.5
The number of times the associated hostTimeInOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hostTimeHighCapacityInOctets 1.3.6.1.2.1.16.4.6.1.6
The number of octets transmitted to this address since it was added to the hostTimeHighCapacityTable (excluding framing bits but including FCS octets), except for those octets in bad packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hostTimeHighCapacityOutOverflowOctets 1.3.6.1.2.1.16.4.6.1.7
The number of times the associated hostTimeOutOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hostTimeHighCapacityOutOctets 1.3.6.1.2.1.16.4.6.1.8
The number of octets transmitted by this address since it was added to the hostTimeTable (excluding framing bits but including FCS octets), including those octets in bad packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hostTopNRateBase 1.3.6.1.2.1.16.5.1.1.3
The variable for each host that the hostTopNRate variable is based upon, as well as a control for the table that the results will be reported in. This object may not be modified if the associated hostTopNStatus [RFC 1757] object is equal to valid(1). If this value is less than or equal to 7, when the report is prepared, entries are created in the hostTopNTable associated with this object. If this value is greater than or equal to 8, when the report is prepared, entries are created in the hostTopNHighCapacityTable associated with this object.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hostTopNInPkts(1), hostTopNOutPkts(2), hostTopNInOctets(3), hostTopNOutOctets(4), hostTopNOutErrors(5), hostTopNOutBroadcastPkts(6), hostTopNOutMulticastPkts(7), hostTopNHCInPkts(8), hostTopNHCOutPkts(9), hostTopNHCInOctets(10), hostTopNHCOutOctets(11)  

hostTopNHighCapacityTable 1.3.6.1.2.1.16.5.3
Contains the High Capacity RMON extensions to the RMON-1 hostTopNTable when hostTopNRateBase specifies a High Capacity TopN Report.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HostTopNHighCapacityEntry

hostTopNHighCapacityEntry 1.3.6.1.2.1.16.5.3.1
Contains the High Capacity RMON extensions to the RMON-1 hostTopNEntry when hostTopNRateBase specifies a High Capacity TopN Report. These objects will be created by the agent for all hostTopNEntries associated with whichever hostTopNControlEntries have a hostTopNRateBase that specify a high capacity report.
Status: current Access: not-accessible
OBJECT-TYPE    
  HostTopNHighCapacityEntry  

hostTopNHighCapacityBaseRate 1.3.6.1.2.1.16.5.3.1.1
The amount of change in the selected variable during this sampling interval, modulo 2^32. The selected variable is this host's instance of the object selected by hostTopNRateBase.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hostTopNHighCapacityOverflowRate 1.3.6.1.2.1.16.5.3.1.2
The amount of change in the selected variable during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32). The selected variable is this host's instance of the object selected by hostTopNRateBase.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hostTopNHighCapacityRate 1.3.6.1.2.1.16.5.3.1.3
The amount of change in the selected variable during this sampling interval. The selected variable is this host's instance of the object selected by hostTopNRateBase.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

matrixSDHighCapacityTable 1.3.6.1.2.1.16.6.5
Contains the High Capacity RMON extensions to the RMON-1 matrixSDTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MatrixSDHighCapacityEntry

matrixSDHighCapacityEntry 1.3.6.1.2.1.16.6.5.1
Contains the High Capacity RMON extensions to the RMON-1 matrixSDEntry. These objects will be created by the agent for all matrixSDEntries associated with whichever matrixControlEntries it deems appropriate. (i.e., either all matrixSDHighCapacityEntries associated with a particular matrixControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  MatrixSDHighCapacityEntry  

matrixSDHighCapacityOverflowPkts 1.3.6.1.2.1.16.6.5.1.1
The number of times the associated matrixSDPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

matrixSDHighCapacityPkts 1.3.6.1.2.1.16.6.5.1.2
The number of packets transmitted from the source address to the destination address (this number includes bad packets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

matrixSDHighCapacityOverflowOctets 1.3.6.1.2.1.16.6.5.1.3
The number of times the associated matrixSDOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

matrixSDHighCapacityOctets 1.3.6.1.2.1.16.6.5.1.4
The number of octets (excluding framing bits but including FCS octets) contained in all packets transmitted from the source address to the destination address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

matrixDSHighCapacityTable 1.3.6.1.2.1.16.6.6
Contains the High Capacity RMON extensions to the RMON-1 matrixDSTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MatrixDSHighCapacityEntry

matrixDSHighCapacityEntry 1.3.6.1.2.1.16.6.6.1
Contains the High Capacity RMON extensions to the RMON-1 matrixDSEntry. These objects will be created by the agent for all matrixDSEntries associated with whichever matrixControlEntries it deems appropriate. (i.e., either all matrixDSHighCapacityEntries associated with a particular matrixControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  MatrixDSHighCapacityEntry  

matrixDSHighCapacityOverflowPkts 1.3.6.1.2.1.16.6.6.1.1
The number of times the associated matrixDSPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

matrixDSHighCapacityPkts 1.3.6.1.2.1.16.6.6.1.2
The number of packets transmitted from the source address to the destination address (this number includes bad packets).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

matrixDSHighCapacityOverflowOctets 1.3.6.1.2.1.16.6.6.1.3
The number of times the associated matrixDSOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

matrixDSHighCapacityOctets 1.3.6.1.2.1.16.6.6.1.4
The number of octets (excluding framing bits but including FCS octets) contained in all packets transmitted from the source address to the destination address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

captureBufferHighCapacityTable 1.3.6.1.2.1.16.8.3
Contains the High Capacity RMON extensions to the RMON captureBufferTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CaptureBufferHighCapacityEntry

captureBufferHighCapacityEntry 1.3.6.1.2.1.16.8.3.1
Contains the High Capacity RMON extensions to the RMON captureBufferEntry. These objects will be created by the agent for all captureBufferEntries associated with whichever bufferControlEntries it deems appropriate. (i.e., either all captureBufferHighCapacityEntries associated with a particular bufferControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  CaptureBufferHighCapacityEntry  

captureBufferPacketHighCapacityTime 1.3.6.1.2.1.16.8.3.1.1
The number of nanoseconds that had passed since this capture buffer was first turned on when this packet was captured, modulo 10^6. This object is used in conjunction with existing timestamp object. This object returns the number of nano-seconds to be added to to number of milli-seconds obtained from the captureBufferPacketTime object, to obtain more accurate inter packet arrival time.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999999  

protocolDistStatsHighCapacityTable 1.3.6.1.2.1.16.12.3
Contains the High Capacity RMON extensions to the RMON-2 protocolDistStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProtocolDistStatsHighCapacityEntry

protocolDistStatsHighCapacityEntry 1.3.6.1.2.1.16.12.3.1
Contains the High Capacity RMON extensions to the RMON-2 protocolDistStatsTable. These objects will be created by the agent for all protocolDistStatsEntries associated with whichever protocolDistControlEntries it deems appropriate. (i.e., either all protocolDistStatsHighCapacityEntries associated with a particular protocolDistControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  ProtocolDistStatsHighCapacityEntry  

protocolDistStatsHighCapacityOverflowPkts 1.3.6.1.2.1.16.12.3.1.1
The number of times the associated protocolDistStatsPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

protocolDistStatsHighCapacityPkts 1.3.6.1.2.1.16.12.3.1.2
The number of packets without errors received of this protocol type. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

protocolDistStatsHighCapacityOverflowOctets 1.3.6.1.2.1.16.12.3.1.3
The number of times the associated protocolDistStatsOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

protocolDistStatsHighCapacityOctets 1.3.6.1.2.1.16.12.3.1.4
The number of octets in packets received of this protocol type since it was added to the protocolDistStatsTable (excluding framing bits but including FCS octets), except for those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlHostHighCapacityTable 1.3.6.1.2.1.16.14.3
Contains the High Capacity RMON extensions to the RMON-2 nlHostTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NlHostHighCapacityEntry

nlHostHighCapacityEntry 1.3.6.1.2.1.16.14.3.1
Contains the High Capacity RMON extensions to the RMON-2 nlHostEntry. These objects will be created by the agent for all nlHostEntries associated with whichever hlHostControlEntries it deems appropriate. (i.e., either all nlHostHighCapacityEntries associated with a particular hlHostControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  NlHostHighCapacityEntry  

nlHostHighCapacityInOverflowPkts 1.3.6.1.2.1.16.14.3.1.1
The number of times the associated nlHostInPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

nlHostHighCapacityInPkts 1.3.6.1.2.1.16.14.3.1.2
The number of packets without errors transmitted to this address since it was added to the nlHostHighCapacityTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlHostHighCapacityOutOverflowPkts 1.3.6.1.2.1.16.14.3.1.3
The number of times the associated nlHostOutPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

nlHostHighCapacityOutPkts 1.3.6.1.2.1.16.14.3.1.4
The number of packets without errors transmitted by this address since it was added to the nlHostHighCapacityTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlHostHighCapacityInOverflowOctets 1.3.6.1.2.1.16.14.3.1.5
The number of times the associated nlHostInOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

nlHostHighCapacityInOctets 1.3.6.1.2.1.16.14.3.1.6
The number of octets transmitted to this address since it was added to the nlHostHighCapacityTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlHostHighCapacityOutOverflowOctets 1.3.6.1.2.1.16.14.3.1.7
The number of times the associated nlHostOutOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

nlHostHighCapacityOutOctets 1.3.6.1.2.1.16.14.3.1.8
The number of octets transmitted by this address since it was added to the nlHostHighCapacityTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlMatrixSDHighCapacityTable 1.3.6.1.2.1.16.15.6
Contains the High Capacity RMON extensions to the RMON-2 nlMatrixTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NlMatrixSDHighCapacityEntry

nlMatrixSDHighCapacityEntry 1.3.6.1.2.1.16.15.6.1
Contains the High Capacity RMON extensions to the RMON-2 nlMatrixEntry. These objects will be created by the agent for all nlMatrixSDEntries associated with whichever hlMatrixControlEntries it deems appropriate. (i.e., either all nlMatrixSDHighCapacityEntries associated with a particular hlMatrixControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  NlMatrixSDHighCapacityEntry  

nlMatrixSDHighCapacityOverflowPkts 1.3.6.1.2.1.16.15.6.1.1
The number of times the associated nlMatrixSDPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

nlMatrixSDHighCapacityPkts 1.3.6.1.2.1.16.15.6.1.2
The number of packets without errors transmitted from the source address to the destination address since this entry was added to the nlMatrixSDHighCapacityTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlMatrixSDHighCapacityOverflowOctets 1.3.6.1.2.1.16.15.6.1.3
The number of times the associated nlMatrixSDOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

nlMatrixSDHighCapacityOctets 1.3.6.1.2.1.16.15.6.1.4
The number of octets transmitted from the source address to the destination address since this entry was added to the nlMatrixSDHighCapacityTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlMatrixDSHighCapacityTable 1.3.6.1.2.1.16.15.7
Contains the High Capacity RMON extensions to the RMON-2 nlMatrixDSTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NlMatrixDSHighCapacityEntry

nlMatrixDSHighCapacityEntry 1.3.6.1.2.1.16.15.7.1
Contains the High Capacity RMON extensions to the RMON-2 nlMatrixDSEntry. These objects will be created by the agent for all nlMatrixDSEntries associated with whichever hlmatrixControlEntries it deems appropriate. (i.e., either all nlMatrixDSHighCapacityEntries associated with a particular hlMatrixControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  NlMatrixDSHighCapacityEntry  

nlMatrixDSHighCapacityOverflowPkts 1.3.6.1.2.1.16.15.7.1.1
The number of times the associated nlMatrixDSPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

nlMatrixDSHighCapacityPkts 1.3.6.1.2.1.16.15.7.1.2
The number of packets without errors transmitted from the source address to the destination address since this entry was added to the nlMatrixHighCapacityDSTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlMatrixDSHighCapacityOverflowOctets 1.3.6.1.2.1.16.15.7.1.3
The number of times the associated nlMatrixDSOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

nlMatrixDSHighCapacityOctets 1.3.6.1.2.1.16.15.7.1.4
The number of octets transmitted from the source address to the destination address since this entry was added to the nlMatrixDSHighCapacityTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

nlMatrixTopNControlRateBase 1.3.6.1.2.1.16.15.4.1.3
The variable for each nlMatrix[SD/DS] entry that the nlMatrixTopNEntries are sorted by, as well as a control for the table that the results will be reported in. This object may not be modified if the associated nlMatrixTopNControlStatus object is equal to active(1). If this value is less than or equal to 2, when the report is prepared, entries are created in the nlMatrixTopNTable associated with this object. If this value is greater than or equal to 3, when the report is prepared, entries are created in the nlMatrixTopNHighCapacityTable associated with this object.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER nlMatrixTopNPkts(1), nlMatrixTopNOctets(2), nlMatrixTopNHighCapacityPkts(3), nlMatrixTopNHighCapacityOctets(4)  

nlMatrixTopNHighCapacityTable 1.3.6.1.2.1.16.15.8
Contains the High Capacity RMON extensions to the RMON-2 nlMatrixTopNTable when nlMatrixTopNControlRateBase specifies a High Capacity TopN Report.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NlMatrixTopNHighCapacityEntry

nlMatrixTopNHighCapacityEntry 1.3.6.1.2.1.16.15.8.1
Contains the High Capacity RMON extensions to the RMON-2 nlMatrixTopNEntry when nlMatrixTopNControlRateBase specifies a High Capacity TopN Report. These objects will be created by the agent for all nlMatrixTopNEntries associated with whichever nlMatrixTopNControlEntries have a nlMatrixTopNControlRateBase that specify a high capacity report.
Status: current Access: not-accessible
OBJECT-TYPE    
  NlMatrixTopNHighCapacityEntry  

nlMatrixTopNHighCapacityBasePktRate 1.3.6.1.2.1.16.15.8.1.1
The number of packets seen from the source host to the destination host during this sampling interval, modulo 2^32, counted using the rules for counting the nlMatrixSDPkts object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nlMatrixTopNHighCapacityOverflowPktRate 1.3.6.1.2.1.16.15.8.1.2
The number of packets seen from the source host to the destination host during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32), and counted using the rules for counting the nlMatrixSDPkts object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nlMatrixTopNHighCapacityPktRate 1.3.6.1.2.1.16.15.8.1.3
The number of packets seen from the source host to the destination host during this sampling interval, counted using the rules for counting the nlMatrixSDPkts object. If the value of nlMatrixTopNControlRateBase is nlMatrixTopNHighCapacityPkts, this variable will be used to sort this report.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

nlMatrixTopNHighCapacityReverseBasePktRate 1.3.6.1.2.1.16.15.8.1.4
The number of packets seen from the destination host to the source host during this sampling interval, modulo 2^32, counted using the rules for counting the nlMatrixSDPkts object (note that the corresponding nlMatrixSDPkts object selected is the one whose source address is equal to nlMatrixTopNDestAddress and whose destination address is equal to nlMatrixTopNSourceAddress.) Note that if the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNHighCapacityPkts, the sort of topN entries is based entirely on nlMatrixTopNHighCapacityPktRate, and not on the value of this object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nlMatrixTopNHighCapacityReverseOverflowPktRate 1.3.6.1.2.1.16.15.8.1.5
The number of packets seen from the destination host to the source host during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32), and counted using the rules for counting the nlMatrixSDPkts object (note that the corresponding nlMatrixSDPkts object selected is the one whose source address is equal to nlMatrixTopNDestAddress and whose destination address is equal to nlMatrixTopNSourceAddress.) Note that if the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNHighCapacityPkts, the sort of topN entries is based entirely on nlMatrixTopNHighCapacityPktRate, and not on the value of this object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nlMatrixTopNHighCapacityReversePktRate 1.3.6.1.2.1.16.15.8.1.6
The number of packets seen from the destination host to the source host during this sampling interval, counted using the rules for counting the nlMatrixSDPkts object (note that the corresponding nlMatrixSDPkts object selected is the one whose source address is equal to nlMatrixTopNDestAddress and whose destination address is equal to nlMatrixTopNSourceAddress.) Note that if the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNHighCapacityPkts, the sort of topN entries is based entirely on nlMatrixTopNHighCapacityPktRate, and not on the value of this object.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

nlMatrixTopNHighCapacityBaseOctetRate 1.3.6.1.2.1.16.15.8.1.7
The number of octets seen from the source host to the destination host during this sampling interval, modulo 2^32, counted using the rules for counting the nlMatrixSDOctets object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nlMatrixTopNHighCapacityOverflowOctetRate 1.3.6.1.2.1.16.15.8.1.8
The number of octets seen from the source host to the destination host during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32), and counted using the rules for counting the nlMatrixSDOctets object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nlMatrixTopNHighCapacityOctetRate 1.3.6.1.2.1.16.15.8.1.9
The number of octets seen from the source host to the destination host during this sampling interval, counted using the rules for counting the nlMatrixSDOctets object. If the value of nlMatrixTopNControlRateBase is nlMatrixTopNHighCapacityOctets, this variable will be used to sort this report.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

nlMatrixTopNHighCapacityReverseBaseOctetRate 1.3.6.1.2.1.16.15.8.1.10
The number of octets seen from the destination host to the source host during this sampling interval, modulo 2^32, counted using the rules for counting the nlMatrixSDOctets object (note that the corresponding nlMatrixSDOctets object selected is the one whose source address is equal to nlMatrixTopNDestAddress and whose destination address is equal to nlMatrixTopNSourceAddress.) Note that if the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNHighCapacityOctets, the sort of topN entries is based entirely on nlMatrixTopNHighCapacityOctetRate, and not on the value of this object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nlMatrixTopNHighCapacityReverseOverflowOctetRate 1.3.6.1.2.1.16.15.8.1.11
The number of octets seen from the destination host to the source host during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32), and counted using the rules for counting the nlMatrixSDOctets object (note that the corresponding nlMatrixSDOctets object selected is the one whose source address is equal to nlMatrixTopNDestAddress and whose destination address is equal to nlMatrixTopNSourceAddress.) Note that if the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNHighCapacityOctets, the sort of topN entries is based entirely on nlMatrixTopNHighCapacityOctetRate, and not on the value of this object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nlMatrixTopNHighCapacityReverseOctetRate 1.3.6.1.2.1.16.15.8.1.12
The number of octets seen from the destination host to the source host during this sampling interval, counted using the rules for counting the nlMatrixSDOctets object (note that the corresponding nlMatrixSDOctets object selected is the one whose source address is equal to nlMatrixTopNDestAddress and whose destination address is equal to nlMatrixTopNSourceAddress.) Note that if the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNHighCapacityOctets, the sort of topN entries is based entirely on nlMatrixTopNHighCapacityOctetRate, and not on the value of this object.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

alHostHighCapacityTable 1.3.6.1.2.1.16.16.2
Contains the High Capacity RMON extensions to the RMON-2 alHostTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlHostHighCapacityEntry

alHostHighCapacityEntry 1.3.6.1.2.1.16.16.2.1
Contains the High Capacity RMON extensions to the RMON-2 alHostEntry. These objects will be created by the agent for all alHostEntries associated with whichever hlHostControlEntries it deems appropriate. (i.e., either all alHostHighCapacityEntries associated with a particular hlHostControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  AlHostHighCapacityEntry  

alHostHighCapacityInOverflowPkts 1.3.6.1.2.1.16.16.2.1.1
The number of times the associated alHostInPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

alHostHighCapacityInPkts 1.3.6.1.2.1.16.16.2.1.2
The number of packets of this protocol type without errors transmitted to this address since it was added to the alHostHighCapacityTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

alHostHighCapacityOutOverflowPkts 1.3.6.1.2.1.16.16.2.1.3
The number of times the associated alHostOutPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

alHostHighCapacityOutPkts 1.3.6.1.2.1.16.16.2.1.4
The number of packets of this protocol type without errors transmitted by this address since it was added to the alHostHighCapacityTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

alHostHighCapacityInOverflowOctets 1.3.6.1.2.1.16.16.2.1.5
The number of times the associated alHostInOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

alHostHighCapacityInOctets 1.3.6.1.2.1.16.16.2.1.6
The number of octets transmitted to this address of this protocol type since it was added to the alHostHighCapacityTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

alHostHighCapacityOutOverflowOctets 1.3.6.1.2.1.16.16.2.1.7
The number of times the associated alHostOutOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

alHostHighCapacityOutOctets 1.3.6.1.2.1.16.16.2.1.8
The number of octets transmitted by this address of this protocol type since it was added to the alHostHighCapacityTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

alMatrixSDHighCapacityTable 1.3.6.1.2.1.16.17.5
Contains the High Capacity RMON extensions to the RMON-2 alMatrixSDTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlMatrixSDHighCapacityEntry

alMatrixSDHighCapacityEntry 1.3.6.1.2.1.16.17.5.1
Contains the High Capacity RMON extensions to the RMON-2 alMatrixSDEntry. These objects will be created by the agent for all alMatrixSDEntries associated with whichever hlMatrixControlEntries it deems appropriate. (i.e., either all alMatrixSDHighCapacityEntries associated with a particular hlMatrixControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  AlMatrixSDHighCapacityEntry  

alMatrixSDHighCapacityOverflowPkts 1.3.6.1.2.1.16.17.5.1.1
The number of times the associated alMatrixSDPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

alMatrixSDHighCapacityPkts 1.3.6.1.2.1.16.17.5.1.2
The number of packets of this protocol type without errors transmitted from the source address to the destination address since this entry was added to the alMatrixSDHighCapacityTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

alMatrixSDHighCapacityOverflowOctets 1.3.6.1.2.1.16.17.5.1.3
The number of times the associated alMatrixSDOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

alMatrixSDHighCapacityOctets 1.3.6.1.2.1.16.17.5.1.4
The number of octets in packets of this protocol type transmitted from the source address to the destination address since this entry was added to the alMatrixSDHighCapacityTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

alMatrixDSHighCapacityTable 1.3.6.1.2.1.16.17.6
Contains the High Capacity RMON extensions to the RMON-2 alMatrixDSTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlMatrixDSHighCapacityEntry

alMatrixDSHighCapacityEntry 1.3.6.1.2.1.16.17.6.1
Contains the High Capacity RMON extensions to the RMON-2 alMatrixSDTable. These objects will be created by the agent for all alMatrixDSEntries associated with whichever hlMatrixControlEntries it deems appropriate. (i.e., either all alMatrixDSHighCapacityEntries associated with a particular hlMatrixControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  AlMatrixDSHighCapacityEntry  

alMatrixDSHighCapacityOverflowPkts 1.3.6.1.2.1.16.17.6.1.1
The number of times the associated alMatrixDSPkts counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

alMatrixDSHighCapacityPkts 1.3.6.1.2.1.16.17.6.1.2
The number of packets of this protocol type without errors transmitted from the source address to the destination address since this entry was added to the alMatrixDSHighCapacityTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

alMatrixDSHighCapacityOverflowOctets 1.3.6.1.2.1.16.17.6.1.3
The number of times the associated alMatrixDSOctets counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

alMatrixDSHighCapacityOctets 1.3.6.1.2.1.16.17.6.1.4
The number of octets in packets of this protocol type transmitted from the source address to the destination address since this entry was added to the alMatrixDSHighCapacityTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter64  

alMatrixTopNControlRateBase 1.3.6.1.2.1.16.17.3.1.3
The variable for each alMatrix[SD/DS] entry that the alMatrixTopNEntries are sorted by, as well as the selector of the view of the matrix table that will be used, as well as a control for the table that the results will be reported in. The values alMatrixTopNTerminalsPkts, alMatrixTopNTerminalsOctets, alMatrixTopNTerminalsHighCapacityPkts, and alMatrixTopNTerminalsHighCapacityOctets cause collection only from protocols that have no child protocols that are counted. The values alMatrixTopNAllPkts, alMatrixTopNAllOctets, alMatrixTopNAllHighCapacityPkts, and alMatrixTopNAllHighCapacityOctets cause collection from all alMatrix entries. This object may not be modified if the associated alMatrixTopNControlStatus object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER alMatrixTopNTerminalsPkts(1), alMatrixTopNTerminalsOctets(2), alMatrixTopNAllPkts(3), alMatrixTopNAllOctets(4), alMatrixTopNTerminalsHighCapacityPkts(5), alMatrixTopNTerminalsHighCapacityOctets(6), alMatrixTopNAllHighCapacityPkts(7), alMatrixTopNAllHighCapacityOctets(8)  

alMatrixTopNHighCapacityTable 1.3.6.1.2.1.16.17.7
Contains the High Capacity RMON extensions to the RMON-2 alMatrixTopNTable when alMatrixTopNControlRateBase specifies a High Capacity TopN Report.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlMatrixTopNHighCapacityEntry

alMatrixTopNHighCapacityEntry 1.3.6.1.2.1.16.17.7.1
Contains the High Capacity RMON extensions to the RMON-2 alMatrixTopNEntry when alMatrixTopNControlRateBase specifies a High Capacity TopN Report. These objects will be created by the agent for all alMatrixTopNEntries associated with whichever alMatrixTopNControlEntries have a alMatrixTopNControlRateBase that specify a high capacity report.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlMatrixTopNHighCapacityEntry  

alMatrixTopNHighCapacityBasePktRate 1.3.6.1.2.1.16.17.7.1.1
The number of packets seen of this protocol from the source host to the destination host during this sampling interval, modulo 2^32, counted using the rules for counting the alMatrixSDPkts object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

alMatrixTopNHighCapacityOverflowPktRate 1.3.6.1.2.1.16.17.7.1.2
The number of packets seen of this protocol from the source host to the destination host during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32), and counted using the rules for counting the alMatrixSDPkts object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

alMatrixTopNHighCapacityPktRate 1.3.6.1.2.1.16.17.7.1.3
The number of packets seen of this protocol from the source host to the destination host during this sampling interval, counted using the rules for counting the alMatrixSDPkts object. If the value of alMatrixTopNControlRateBase is alMatrixTopNTerminalsPkts, alMatrixTopNAllPkts, alMatrixTopNTerminalsHighCapacityPkts, or alMatrixTopNAllHighCapacityPkts, this variable will be used to sort this report.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

alMatrixTopNHighCapacityReverseBasePktRate 1.3.6.1.2.1.16.17.7.1.4
The number of packets seen of this protocol from the destination host to the source host during this sampling interval, modulo 2^32, counted using the rules for counting the alMatrixSDPkts object (note that the corresponding alMatrixSDPkts object selected is the one whose source address is equal to alMatrixTopNDestAddress and whose destination address is equal to alMatrixTopNSourceAddress.)
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

alMatrixTopNHighCapacityReverseOverflowPktRate 1.3.6.1.2.1.16.17.7.1.5
The number of packets seen of this protocol from the destination host to the source host during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32), and counted using the rules for counting the alMatrixSDPkts object (note that the corresponding alMatrixSDPkts object selected is the one whose source address is equal to alMatrixTopNDestAddress and whose destination address is equal to alMatrixTopNSourceAddress.)
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

alMatrixTopNHighCapacityReversePktRate 1.3.6.1.2.1.16.17.7.1.6
The number of packets seen of this protocol from the destination host to the source host during this sampling interval, counted using the rules for counting the alMatrixSDPkts object (note that the corresponding alMatrixSDPkts object selected is the one whose source address is equal to alMatrixTopNDestAddress and whose destination address is equal to alMatrixTopNSourceAddress.)
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

alMatrixTopNHighCapacityBaseOctetRate 1.3.6.1.2.1.16.17.7.1.7
The number of octets seen of this protocol from the source host to the destination host during this sampling interval, modulo 2^32, counted using the rules for counting the alMatrixSDOctets object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

alMatrixTopNHighCapacityOverflowOctetRate 1.3.6.1.2.1.16.17.7.1.8
The number of octets seen of this protocol from the source host to the destination host during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32), and counted using the rules for counting the alMatrixSDOctets object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

alMatrixTopNHighCapacityOctetRate 1.3.6.1.2.1.16.17.7.1.9
The number of octets seen of this protocol from the source host to the destination host during this sampling interval, counted using the rules for counting the alMatrixSDOctets object. If the value of alMatrixTopNControlRateBase is alMatrixTopNTerminalsOctets, alMatrixTopNAllOctets, alMatrixTopNTerminalsHighCapacityOctets, or alMatrixTopNAllHighCapacityOctets, this variable will be used to sort this report.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

alMatrixTopNHighCapacityReverseBaseOctetRate 1.3.6.1.2.1.16.17.7.1.10
The number of octets seen of this protocol from the destination host to the source host during this sampling interval, modulo 2^32, counted using the rules for counting the alMatrixSDOctets object (note that the corresponding alMatrixSDOctets object selected is the one whose source address is equal to alMatrixTopNDestAddress and whose destination address is equal to alMatrixTopNSourceAddress.)
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

alMatrixTopNHighCapacityReverseOverflowOctetRate 1.3.6.1.2.1.16.17.7.1.11
The number of octets seen of this protocol from the destination host to the source host during this sampling interval, divided by 2^32, truncating fractions (i.e., X DIV 2^32), and counted using the rules for counting the alMatrixSDOctets object (note that the corresponding alMatrixSDOctets object selected is the one whose source address is equal to alMatrixTopNDestAddress and whose destination address is equal to alMatrixTopNSourceAddress.)
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

alMatrixTopNHighCapacityReverseOctetRate 1.3.6.1.2.1.16.17.7.1.12
The number of octets seen of this protocol from the destination host to the source host during this sampling interval, counted using the rules for counting the alMatrixSDOctets object (note that the corresponding alMatrixSDOctets object selected is the one whose source address is equal to alMatrixTopNDestAddress and whose destination address is equal to alMatrixTopNSourceAddress.)
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

usrHistoryHighCapacityTable 1.3.6.1.2.1.16.18.4
Contains the High Capacity RMON extensions to the RMON-2 usrHistoryTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsrHistoryHighCapacityEntry

usrHistoryHighCapacityEntry 1.3.6.1.2.1.16.18.4.1
Contains the High Capacity RMON extensions to the RMON-2 usrHistoryEntry. These objects will be created by the agent for all usrHistoryEntries associated with whichever usrHistoryControlEntries it deems appropriate. (i.e., either all usrHistoryHighCapacityEntries associated with a particular usrHistoryControlEntry will be created, or none of them will be.)
Status: current Access: not-accessible
OBJECT-TYPE    
  UsrHistoryHighCapacityEntry  

usrHistoryHighCapacityOverflowAbsValue 1.3.6.1.2.1.16.18.4.1.1
The absolute value (i.e. unsigned value) of the user-specified statistic during the last sampling period, divided by 2^32, truncating fractions (i.e., X DIV 2^32). The value during the current sampling period is not made available until the period is completed. To obtain the true value for this sampling interval, the associated instance of usrHistoryValStatus must be checked, and usrHistoryAbsValue adjusted as necessary. If the MIB instance could not be accessed during the sampling interval, then this object will have a value of zero and the associated instance of usrHistoryValStatus will be set to 'valueNotAvailable(1)'.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

usrHistoryHighCapacityAbsValue 1.3.6.1.2.1.16.18.4.1.2
The absolute value (i.e. unsigned value) of the user-specified statistic during the last sampling period. The value during the current sampling period is not made available until the period is completed. To obtain the true value for this sampling interval, the associated instance of usrHistoryValStatus must be checked, and usrHistoryHighCapacityAbsValue adjusted as necessary. If the MIB instance could not be accessed during the sampling interval, then this object will have a value of zero and the associated instance of usrHistoryValStatus will be set to 'valueNotAvailable(1)'.
Status: current Access: read-only
OBJECT-TYPE    
  RmonGauge64  

hcRMONCapabilities 1.3.6.1.2.1.16.19.16
An indication of the High Capacity RMON MIB groups supported on at least one interface by this probe.
Status: current Access: read-only
OBJECT-TYPE    
  BITS mediaIndependentGroup(0), etherStatsHighCapacityGroup(1), etherHistoryHighCapacityGroup(2), hostHighCapacityGroup(3), hostTopNHighCapacityGroup(4), matrixHighCapacityGroup(5), captureBufferHighCapacityGroup(6), protocolDistributionHighCapacityGroup(7), nlHostHighCapacityGroup(8), nlMatrixHighCapacityGroup(9), nlMatrixTopNHighCapacityGroup(10), alHostHighCapacityGroup(11), alMatrixHighCapacityGroup(12), alMatrixTopNHighCapacityGroup(13), usrHistoryHighCapacityGroup(14)  

hcRmonMIBCompliances 1.3.6.1.2.1.16.20.6
OBJECT IDENTIFIER    

hcRmonMIBGroups 1.3.6.1.2.1.16.20.7
OBJECT IDENTIFIER    

hcRmonMIBCompliance 1.3.6.1.2.1.16.20.6.1
Describes the minimum requirements for conformance to the high capacity RMON MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

hcRmon2MIBCompliance 1.3.6.1.2.1.16.20.6.2
Describes the requirements for conformance to the High Capacity RMON 2 MIB
Status: current Access: read-only
MODULE-COMPLIANCE    

hcRmon2MIBApplicationLayerCompliance 1.3.6.1.2.1.16.20.6.3
Describes the requirements for conformance to the High Capacity RMON2 MIB with Application Layer Enhancements.
Status: current Access: read-only
MODULE-COMPLIANCE    

mediaIndependentGroup 1.3.6.1.2.1.16.20.7.1
Collects utilization statistics for any type of network.
Status: current Access: read-only
OBJECT-GROUP    

etherStatsHighCapacityGroup 1.3.6.1.2.1.16.20.7.2
Collects utilization statistics for ethernet networks.
Status: current Access: read-only
OBJECT-GROUP    

etherHistoryHighCapacityGroup 1.3.6.1.2.1.16.20.7.3
Collects utilization statistics for ethernet networks.
Status: current Access: read-only
OBJECT-GROUP    

hostHighCapacityGroup 1.3.6.1.2.1.16.20.7.4
Collects utilization and error statistics per host.
Status: current Access: read-only
OBJECT-GROUP    

hostTopNHighCapacityGroup 1.3.6.1.2.1.16.20.7.5
Prepares sorted reports of utilization and error statistics per host.
Status: current Access: read-only
OBJECT-GROUP    

matrixHighCapacityGroup 1.3.6.1.2.1.16.20.7.6
Collects utilization statistics per conversation.
Status: current Access: read-only
OBJECT-GROUP    

captureBufferHighCapacityGroup 1.3.6.1.2.1.16.20.7.7
Provides finer granularity timestamps.
Status: current Access: read-only
OBJECT-GROUP    

protocolDistributionHighCapacityGroup 1.3.6.1.2.1.16.20.7.8
Collects the relative amounts of octets and packets for the different protocols detected on a network segment.
Status: current Access: read-only
OBJECT-GROUP    

nlHostHighCapacityGroup 1.3.6.1.2.1.16.20.7.9
Counts the amount of traffic sent from and to each network address discovered by the probe.
Status: current Access: read-only
OBJECT-GROUP    

nlMatrixHighCapacityGroup 1.3.6.1.2.1.16.20.7.10
Counts the amount of traffic sent between each pair of network addresses discovered by the probe.
Status: current Access: read-only
OBJECT-GROUP    

nlMatrixTopNHighCapacityGroup 1.3.6.1.2.1.16.20.7.11
Prepares sorted reports of the amount of traffic sent between each pair of network addresses discovered by the probe.
Status: current Access: read-only
OBJECT-GROUP    

alHostHighCapacityGroup 1.3.6.1.2.1.16.20.7.12
Counts the amount of traffic, by protocol, sent from and to each network address discovered by the probe.
Status: current Access: read-only
OBJECT-GROUP    

alMatrixHighCapacityGroup 1.3.6.1.2.1.16.20.7.13
Counts the amount of traffic, by protocol, sent between each pair of network addresses discovered by the probe.
Status: current Access: read-only
OBJECT-GROUP    

alMatrixTopNHighCapacityGroup 1.3.6.1.2.1.16.20.7.14
Prepares sorted reports of the amount of traffic per protocol sent between each pair of network addresses discovered by the probe.
Status: current Access: read-only
OBJECT-GROUP    

usrHistoryHighCapacityGroup 1.3.6.1.2.1.16.20.7.15
Provides user-defined collection of historical information from MIB objects on the probe with scalability to statistics from high-capacity networks.
Status: current Access: read-only
OBJECT-GROUP    

hcRMONInformationGroup 1.3.6.1.2.1.16.20.7.16
An indication of the high capacity RMON groups supported on at least one interface by this probe.
Status: current Access: read-only
OBJECT-GROUP