H3C-QINQ-MIB

File: H3C-QINQ-MIB.mib (19995 bytes)

Imported modules

SNMPv2-TC SNMPv2-SMI RFC1213-MIB
HUAWEI-3COM-OID-MIB

Imported symbols

RowStatus TEXTUAL-CONVENTION MODULE-IDENTITY
OBJECT-TYPE Integer32 ifIndex
h3cCommon

Defined Types

H3cQinQSwitchState  
TEXTUAL-CONVENTION    
  current INTEGER enabled(1), disabled(2)

H3cQinQBpduTunnelEntry  
SEQUENCE    
  h3cQinQProtocolIndex INTEGER
  h3cQinQBpduRowStatus RowStatus

H3cQinQPriorityRemarkEntry  
SEQUENCE    
  h3cQinQPriorityValue Integer32
  h3cQinQPriorityRemarkValue Integer32
  h3cQinQPriorityRowStatus RowStatus

H3cQinQVidEntry  
SEQUENCE    
  h3cQinQVlanID Integer32
  h3cQinQInboundVidListLow STRING
  h3cQinQInboundVidListHigh STRING
  h3cQinQVidEthernetType Integer32
  h3cQinQVidRowStatus RowStatus

H3cQinQVidSwapEntry  
SEQUENCE    
  h3cQinQVidSwapOld Integer32
  h3cQinQVidSwapNew Integer32
  h3cQinQVidSwapRowStatus RowStatus

H3cQinQPrioritySwapEntry  
SEQUENCE    
  h3cQinQPrioritySwapOld Integer32
  h3cQinQPrioritySwapNew Integer32
  h3cQinQPrioritySwapRowStatus RowStatus

H3cQinQIfConfigEntry  
SEQUENCE    
  h3cQinQIfEthernetType Integer32
  h3cQinQIfSwitch H3cQinQSwitchState
  h3cQinQIfRowStatus RowStatus
  h3cQinQIfServiceTPIDValue Integer32
  h3cQinQIfCustomerTPIDValue Integer32
  h3cQinQIfUplinkSwitch H3cQinQSwitchState
  h3cQinQIfDownlinkSwitch H3cQinQSwitchState

Defined Values

h3cQINQ 1.3.6.1.4.1.2011.10.2.69
HUAWEI-3COM 802.1Q-in-Q MIB
MODULE-IDENTITY    

h3cQinQMibObject 1.3.6.1.4.1.2011.10.2.69.1
OBJECT IDENTIFIER    

h3cQinQGlobalConfigGroup 1.3.6.1.4.1.2011.10.2.69.1.1
OBJECT IDENTIFIER    

h3cQinQBpduTunnelSwitch 1.3.6.1.4.1.2011.10.2.69.1.1.1
The global configuration switch of BPDU 802.1q tunnel. If global configuration is disabled, BPDU tunnel function will be disabled despite of the corresponding configuration of interface. BPDU tunnel function of a certain interface would work only if the global and interface's switch are both enabled.
OBJECT-TYPE    
  H3cQinQSwitchState  

h3cQinQEthernetTypeValue 1.3.6.1.4.1.2011.10.2.69.1.1.2
Ethernet protocol type configuring for a global value. The ethernet protocol type is also the TPID(Tag Protocol Identity) field of a VLAN tag described in 802.1q document. This value can be also configured for an individual interface or VLAN. The node that configure this value for a single interface is h3cQinQIfEthernetType, whose priority is higher than h3cQinQEthernetTypeValue. That means, if the value configured for a interface is different from the global value, the switch will select the configuration of the interface and ignore the global configuration. The ethernet protocol type of node h3cQinQVidEthernetType that configured for a VLAN has the highest priority.
OBJECT-TYPE    
  Integer32 1..65535  

h3cQinQServiceTPIDValue 1.3.6.1.4.1.2011.10.2.69.1.1.3
Ethernet protocol type configured for service VLAN tags globally. The ethernet protocol type is also the TPID(Tag Protocol Identity) field of a VLAN tag described in 802.1q document. This value can be also configured for an individual interface. The node that configure this value for a single interface is h3cQinQIfServiceTPIDValue, whose priority is higher than h3cQinQServiceTPIDValue. That means, if the value configured for a interface is different from the global value, the switch will select the configuration of the interface and ignore the global configuration.
OBJECT-TYPE    
  Integer32 1..65535  

h3cQinQCustomerTPIDValue 1.3.6.1.4.1.2011.10.2.69.1.1.4
Ethernet protocol type configured for customer VLAN tags globally. The ethernet protocol type is also the TPID(Tag Protocol Identity) field of a VLAN tag described in 802.1q document. This value can be also configured for an individual interface. The node that configure this value for a single interface is h3cQinQIfCustomerTPIDValue, whose priority is higher than h3cQinQCustomerTPIDValue. That means, if the value configured for a interface is different from the global value, the switch will select the configuration of the interface and ignore the global configuration.
OBJECT-TYPE    
  Integer32 1..65535  

h3cQinQBpduTunnelTable 1.3.6.1.4.1.2011.10.2.69.1.2
A table for configuring 802.1q BPDU tunnel function for interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cQinQBpduTunnelEntry

h3cQinQBpduTunnelEntry 1.3.6.1.4.1.2011.10.2.69.1.2.1
An entry for configuring 802.1q BPDU tunnel function for interfaces.
OBJECT-TYPE    
  H3cQinQBpduTunnelEntry  

h3cQinQProtocolIndex 1.3.6.1.4.1.2011.10.2.69.1.2.1.1
The index of protocol on which the BPDU tunnel state will be set. 'bpdu' represents status of BPDU tunnel. 'stp' represents STP tunnel. 'gvrp' represents GVRP tunnel. 'igmp' represents IGMP tunnel. STP/GVRP/IGMP tunnel will start to work only if BPDU tunnel and STP/GVRP/IGMP tunnel are both enabled.
OBJECT-TYPE    
  INTEGER bpdu(1), stp(2), gvrp(3), igmp(4)  

h3cQinQBpduRowStatus 1.3.6.1.4.1.2011.10.2.69.1.2.1.2
Operation status of this table entry.
OBJECT-TYPE    
  RowStatus  

h3cQinQPriorityRemarkTable 1.3.6.1.4.1.2011.10.2.69.1.3
A table for configuring priority field in 802.1Q-in-Q outer VLAN tag for interfaces. This feature uses the priority of an inner VLAN tag to remark the priority of an outer VLAN tag.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cQinQPriorityRemarkEntry

h3cQinQPriorityRemarkEntry 1.3.6.1.4.1.2011.10.2.69.1.3.1
An entry for configuring priority remark function for interfaces.
OBJECT-TYPE    
  H3cQinQPriorityRemarkEntry  

h3cQinQPriorityValue 1.3.6.1.4.1.2011.10.2.69.1.3.1.1
The priority value in inner VLAN tag. Since the priority range is from 0 to 7, yet the index range is from 1 to 8. Thus, the actual priority value equals to the value that subtracts 1 from corresponding index value.
OBJECT-TYPE    
  Integer32 1..8  

h3cQinQPriorityRemarkValue 1.3.6.1.4.1.2011.10.2.69.1.3.1.2
The new priority value used to fill outer tag.
OBJECT-TYPE    
  Integer32 0..7  

h3cQinQPriorityRowStatus 1.3.6.1.4.1.2011.10.2.69.1.3.1.3
Operation status of this table entry.
OBJECT-TYPE    
  RowStatus  

h3cQinQVidTable 1.3.6.1.4.1.2011.10.2.69.1.4
A table for configuring VLAN ID of the 802.1Q-in-Q interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cQinQVidEntry

h3cQinQVidEntry 1.3.6.1.4.1.2011.10.2.69.1.4.1
An entry for configuring VLAN ID of the 802.1Q-in-Q interfaces.
OBJECT-TYPE    
  H3cQinQVidEntry  

h3cQinQVlanID 1.3.6.1.4.1.2011.10.2.69.1.4.1.1
VLAN ID
OBJECT-TYPE    
  Integer32 1..4094  

h3cQinQInboundVidListLow 1.3.6.1.4.1.2011.10.2.69.1.4.1.2
The inbound VLAN IDs which need 802.1Q-in-Q processing. The VLAN ID range, described by bitmap, is from 1 to 2048. The length of bitmap is 256 in bytes. Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN.
OBJECT-TYPE    
  STRING Size(256)  

h3cQinQInboundVidListHigh 1.3.6.1.4.1.2011.10.2.69.1.4.1.3
The inbound VLAN IDs which need 802.1Q-in-Q processing. The VLAN ID range, described by bitmap, is from 2049 to 4094. The length of bitmap is 256 in bytes. Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN.
OBJECT-TYPE    
  STRING Size(256)  

h3cQinQVidEthernetType 1.3.6.1.4.1.2011.10.2.69.1.4.1.4
Ethernet protocol type configuring for a VLAN.
OBJECT-TYPE    
  Integer32 1..65535  

h3cQinQVidRowStatus 1.3.6.1.4.1.2011.10.2.69.1.4.1.5
Operation status of this table entry.
OBJECT-TYPE    
  RowStatus  

h3cQinQVidSwapTable 1.3.6.1.4.1.2011.10.2.69.1.5
A table for configuring 802.1Q-in-Q inner VLAN ID swapping function for interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cQinQVidSwapEntry

h3cQinQVidSwapEntry 1.3.6.1.4.1.2011.10.2.69.1.5.1
An entry for configuring 802.1Q-in-Q inner VLAN ID swapping function for interfaces.
OBJECT-TYPE    
  H3cQinQVidSwapEntry  

h3cQinQVidSwapOld 1.3.6.1.4.1.2011.10.2.69.1.5.1.1
The old VLAN ID of original 802.1Q packets.
OBJECT-TYPE    
  Integer32 1..4094  

h3cQinQVidSwapNew 1.3.6.1.4.1.2011.10.2.69.1.5.1.2
The new VLAN ID of original 802.1Q packets.
OBJECT-TYPE    
  Integer32 1..4094  

h3cQinQVidSwapRowStatus 1.3.6.1.4.1.2011.10.2.69.1.5.1.3
Operation status of this table entry.
OBJECT-TYPE    
  RowStatus  

h3cQinQPrioritySwapTable 1.3.6.1.4.1.2011.10.2.69.1.6
A table for configuring 802.1Q-in-Q inner VLAN priority swapping function for interfaces. Using this function, the priority of inner VLAN tag can be modified.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cQinQPrioritySwapEntry

h3cQinQPrioritySwapEntry 1.3.6.1.4.1.2011.10.2.69.1.6.1
An entry for configuring 802.1Q-in-Q inner VLAN priority swapping function for interfaces.
OBJECT-TYPE    
  H3cQinQPrioritySwapEntry  

h3cQinQPrioritySwapOld 1.3.6.1.4.1.2011.10.2.69.1.6.1.1
The old priority of original 802.1Q packets. It is the priority of inner VLAN tag. Since the VLAN priority range is from 0 to 7, yet the index range is from 1 to 8. Thus, the actual priority value equals to the value that subtracts 1 from corresponding index value.
OBJECT-TYPE    
  Integer32 1..8  

h3cQinQPrioritySwapNew 1.3.6.1.4.1.2011.10.2.69.1.6.1.2
The new priority of original 802.1Q packets. It is the priority of inner VLAN tag after swapped.
OBJECT-TYPE    
  Integer32 0..7  

h3cQinQPrioritySwapRowStatus 1.3.6.1.4.1.2011.10.2.69.1.6.1.3
Operation status of this table entry.
OBJECT-TYPE    
  RowStatus  

h3cQinQIfConfigTable 1.3.6.1.4.1.2011.10.2.69.1.7
A table for configuring 802.1Q-in-Q functions for interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cQinQIfConfigEntry

h3cQinQIfConfigEntry 1.3.6.1.4.1.2011.10.2.69.1.7.1
An entry for configuring 802.1Q-in-Q functions for interfaces.
OBJECT-TYPE    
  H3cQinQIfConfigEntry  

h3cQinQIfEthernetType 1.3.6.1.4.1.2011.10.2.69.1.7.1.1
Ethernet protocol type configuring for an interface.
OBJECT-TYPE    
  Integer32 1..65535  

h3cQinQIfSwitch 1.3.6.1.4.1.2011.10.2.69.1.7.1.2
Switch of 802.1Q-in-Q functions configuring for an interface.
OBJECT-TYPE    
  H3cQinQSwitchState  

h3cQinQIfRowStatus 1.3.6.1.4.1.2011.10.2.69.1.7.1.3
Operation status of this table entry.
OBJECT-TYPE    
  RowStatus  

h3cQinQIfServiceTPIDValue 1.3.6.1.4.1.2011.10.2.69.1.7.1.4
Service TPID value configured for an interface.
OBJECT-TYPE    
  Integer32 1..65535  

h3cQinQIfCustomerTPIDValue 1.3.6.1.4.1.2011.10.2.69.1.7.1.5
Customer TPID value configured for an interface.
OBJECT-TYPE    
  Integer32 1..65535  

h3cQinQIfUplinkSwitch 1.3.6.1.4.1.2011.10.2.69.1.7.1.6
Switch of the uplink 802.1Q-in-Q function for an interface.
OBJECT-TYPE    
  H3cQinQSwitchState  

h3cQinQIfDownlinkSwitch 1.3.6.1.4.1.2011.10.2.69.1.7.1.7
Switch of the downlink 802.1Q-in-Q function for an interface.
OBJECT-TYPE    
  H3cQinQSwitchState