H3C-IPSEC-MONITOR-MIB

File: H3C-IPSEC-MONITOR-MIB.mib (58618 bytes)

Imported modules

RFC1213-MIB SNMPv2-TC SNMPv2-SMI
SNMPv2-CONF HUAWEI-3COM-OID-MIB

Imported symbols

ifIndex DisplayString TEXTUAL-CONVENTION
IpAddress Integer32 Counter32
Counter64 OBJECT-TYPE MODULE-IDENTITY
Gauge32 NOTIFICATION-TYPE Unsigned32
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
h3cCommon

Defined Types

H3cDiffHellmanGrp  
The Diffie Hellman Group used in the IKE and IPSec negotiations. invalidGroup(2147483647) is defined as invalid value.
TEXTUAL-CONVENTION    
  INTEGER none(0), modp768(1), modp1024(2), modp1536(5), modp2048(14), invalidGroup(2147483647)  

H3cEncapMode  
The encapsulation mode used by an IPSec Phase-2 Tunnel. invalidMode(2147483647) is defined as invalid value.
TEXTUAL-CONVENTION    
  INTEGER tunnel(1), transport(2), invalidMode(2147483647)  

H3cEncryptAlgo  
The encryption algorithm used in the IKE and IPSec negotiations. invalidAlg(2147483647) is defined as invalid value.
TEXTUAL-CONVENTION    
  INTEGER none(0), desCbc(1), ideaCbc(2), blowfishCbc(3), rc5R16B64Cbc(4), tripledesCbc(5), castCbc(6), aesCbc(7), nsaCbc(8), aesCbc128(9), aesCbc192(10), aesCbc256(11), invalidAlg(2147483647)  

H3cAuthAlgo  
The authentication algorithm used in the IKE negotiations. invalidAlg(2147483647) is defined as invalid value.
TEXTUAL-CONVENTION    
  INTEGER none(0), md5(1), sha(2), invalidAlg(2147483647)  

H3cSaProtocol  
The protocol of security association.
TEXTUAL-CONVENTION    
  INTEGER reserved(0), isakmp(1), ah(2), esp(3), ipcomp(4)  

H3cTrapStatus  
The switch which determines whether send a trap or not.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

H3cIPSecIDType  
The type of IPSec Identity.
TEXTUAL-CONVENTION    
  INTEGER reserved(0), ipv4Addr(1), fqdn(2), userFqdn(3), ipv4AddrSubnet(4), ipv6Addr(5), ipv6AddrSubnet(6), ipv4AddrRange(7), ipv6AddrRange(8), derAsn1Dn(9), derAsn1Gn(10), keyId(11)  

H3cTrafficType  
The type of the data flow.
TEXTUAL-CONVENTION    
  INTEGER ipv4Addr(1), ipv4AddrSubnet(4), ipv6Addr(5), ipv6AddrSubnet(6), ipv4AddrRange(7), ipv6AddrRange(8)  

H3cIPSecNegoType  
The type of key used by an IPSec Phase-2 Tunnel. invalidType(2147483647) is defined as invalid value.
TEXTUAL-CONVENTION    
  INTEGER ike(1), manual(2), invalidType(2147483647)  

H3cIPSecTunnelState  
The state of IPSec tunnel.
TEXTUAL-CONVENTION    
  INTEGER active(1), timeout(2)  

H3cIPSecTunnelEntry  
SEQUENCE    
  h3cIPSecTunIfIndex Integer32
  h3cIPSecTunEntryIndex Integer32
  h3cIPSecTunIndex Integer32
  h3cIPSecTunIKETunnelIndex Integer32
  h3cIPSecTunLocalAddr IpAddress
  h3cIPSecTunRemoteAddr IpAddress
  h3cIPSecTunKeyType H3cIPSecNegoType
  h3cIPSecTunEncapMode H3cEncapMode
  h3cIPSecTunInitiator INTEGER
  h3cIPSecTunLifeSize Gauge32
  h3cIPSecTunLifeTime Integer32
  h3cIPSecTunRemainTime Integer32
  h3cIPSecTunActiveTime Integer32
  h3cIPSecTunRemainSize Gauge32
  h3cIPSecTunTotalRefreshes Counter32
  h3cIPSecTunCurrentSaInstances Gauge32
  h3cIPSecTunInSaEncryptAlgo H3cEncryptAlgo
  h3cIPSecTunInSaAhAuthAlgo H3cAuthAlgo
  h3cIPSecTunInSaEspAuthAlgo H3cAuthAlgo
  h3cIPSecTunDiffHellmanGrp H3cDiffHellmanGrp
  h3cIPSecTunOutSaEncryptAlgo H3cEncryptAlgo
  h3cIPSecTunOutSaAhAuthAlgo H3cAuthAlgo
  h3cIPSecTunOutSaEspAuthAlgo H3cAuthAlgo
  h3cIPSecTunPolicyName DisplayString
  h3cIPSecTunPolicyNum Integer32
  h3cIPSecTunStatus INTEGER

H3cIPSecTunnelStatEntry  
SEQUENCE    
  h3cIPSecTunInOctets Counter64
  h3cIPSecTunInDecompOctets Counter64
  h3cIPSecTunInPkts Counter64
  h3cIPSecTunInDropPkts Counter64
  h3cIPSecTunInReplayDropPkts Counter32
  h3cIPSecTunInAuthFails Counter32
  h3cIPSecTunInDecryptFails Counter32
  h3cIPSecTunOutOctets Counter64
  h3cIPSecTunOutUncompOctets Counter64
  h3cIPSecTunOutPkts Counter64
  h3cIPSecTunOutDropPkts Counter64
  h3cIPSecTunOutEncryptFails Counter32
  h3cIPSecTunNoMemoryDropPkts Counter32
  h3cIPSecTunQueueFullDropPkts Counter32
  h3cIPSecTunInvalidLenDropPkts Counter32
  h3cIPSecTunTooLongDropPkts Counter32
  h3cIPSecTunInvalidSaDropPkts Counter32

H3cIPSecSaEntry  
SEQUENCE    
  h3cIPSecSaIndex Integer32
  h3cIPSecSaDirection INTEGER
  h3cIPSecSaValue Unsigned32
  h3cIPSecSaProtocol H3cSaProtocol
  h3cIPSecSaEncryptAlgo H3cEncryptAlgo
  h3cIPSecSaAuthAlgo H3cAuthAlgo
  h3cIPSecSaStatus INTEGER

H3cIPSecTrafficEntry  
SEQUENCE    
  h3cIPSecTrafficLocalType H3cTrafficType
  h3cIPSecTrafficLocalAddr1 IpAddress
  h3cIPSecTrafficLocalAddr2 IpAddress
  h3cIPSecTrafficLocalProtocol Integer32
  h3cIPSecTrafficLocalPort Integer32
  h3cIPSecTrafficRemoteType H3cTrafficType
  h3cIPSecTrafficRemoteAddr1 IpAddress
  h3cIPSecTrafficRemoteAddr2 IpAddress
  h3cIPSecTrafficRemoteProtocol Integer32
  h3cIPSecTrafficRemotePort Integer32

Defined Values

h3cIPSecMonitor 1.3.6.1.4.1.2011.10.2.7
The MIB is designed to get statistic information of IPSec tunnels. With this MIB, we can get information of a certain tunnel or all tunnels.
MODULE-IDENTITY    

h3cIPSecObjects 1.3.6.1.4.1.2011.10.2.7.1
OBJECT IDENTIFIER    

h3cIPSecTunnelTable 1.3.6.1.4.1.2011.10.2.7.1.1
The IPSec Phase-2 Tunnel Table. There is one entry in this table for each active IPSec Phase-2 Tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cIPSecTunnelEntry

h3cIPSecTunnelEntry 1.3.6.1.4.1.2011.10.2.7.1.1.1
Information about h3cIPSecTunnelTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cIPSecTunnelEntry  

h3cIPSecTunIfIndex 1.3.6.1.4.1.2011.10.2.7.1.1.1.1
The interface index( the ifIndex of ifTable ).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cIPSecTunEntryIndex 1.3.6.1.4.1.2011.10.2.7.1.1.1.2
The index of IPSec policy applied in the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cIPSecTunIndex 1.3.6.1.4.1.2011.10.2.7.1.1.1.3
The index of IPSec Phase-2 Tunnel Table. The value of the index is a number which begins at one and is incremented with each tunnel that is created. The value of this object will wrap at 2,147,483,647.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cIPSecTunIKETunnelIndex 1.3.6.1.4.1.2011.10.2.7.1.1.1.4
The index of the associated IPSec Phase-1 IKE Tunnel (IKETunIndex in the IKETunnelTable). 2147483647 is defined as invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cIPSecTunLocalAddr 1.3.6.1.4.1.2011.10.2.7.1.1.1.5
The IP address of the local peer for the IPSec Phase-2 Tunnel. 0.0.0.0 is defined as invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

h3cIPSecTunRemoteAddr 1.3.6.1.4.1.2011.10.2.7.1.1.1.6
The IP address of the remote peer for the IPSec Phase-2 Tunnel. 0.0.0.0 is defined as invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

h3cIPSecTunKeyType 1.3.6.1.4.1.2011.10.2.7.1.1.1.7
The key negotiate mode used by the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cIPSecNegoType  

h3cIPSecTunEncapMode 1.3.6.1.4.1.2011.10.2.7.1.1.1.8
The encapsulation mode used by the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cEncapMode  

h3cIPSecTunInitiator 1.3.6.1.4.1.2011.10.2.7.1.1.1.9
The initiator of this IPSec tunnel. Value none is used for manual IPsec tunnel, for there is no initiator or responder in this method.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local(1), remote(2), none(2147483647)  

h3cIPSecTunLifeSize 1.3.6.1.4.1.2011.10.2.7.1.1.1.10
The negotiated LifeSize of the IPSec Phase-2 Tunnel in kilobytes. 0 is defined as invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

h3cIPSecTunLifeTime 1.3.6.1.4.1.2011.10.2.7.1.1.1.11
The negotiated LifeTime of the IPSec Phase-2 Tunnel in seconds. 2147483647 is defined as invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cIPSecTunRemainTime 1.3.6.1.4.1.2011.10.2.7.1.1.1.12
The remain time of SA in seconds. 2147483647 is defined as invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cIPSecTunActiveTime 1.3.6.1.4.1.2011.10.2.7.1.1.1.13
The duration the IPSec Phase-2 Tunnel has been active in hundredths of seconds. 2147483647 is defined as invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cIPSecTunRemainSize 1.3.6.1.4.1.2011.10.2.7.1.1.1.14
The remain LifeSize of SA in kilobytes. 0 is defined as invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

h3cIPSecTunTotalRefreshes 1.3.6.1.4.1.2011.10.2.7.1.1.1.15
The total number of security association refreshing performed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunCurrentSaInstances 1.3.6.1.4.1.2011.10.2.7.1.1.1.16
The number of security associations which are currently active or expiring.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

h3cIPSecTunInSaEncryptAlgo 1.3.6.1.4.1.2011.10.2.7.1.1.1.17
The encryption algorithm used by the inbound security association of the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cEncryptAlgo  

h3cIPSecTunInSaAhAuthAlgo 1.3.6.1.4.1.2011.10.2.7.1.1.1.18
The authentication algorithm used by the inbound authentication header (AH) security association of the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cAuthAlgo  

h3cIPSecTunInSaEspAuthAlgo 1.3.6.1.4.1.2011.10.2.7.1.1.1.19
The authentication algorithm used by the inbound encapsulation security protocol(ESP) security association of the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cAuthAlgo  

h3cIPSecTunDiffHellmanGrp 1.3.6.1.4.1.2011.10.2.7.1.1.1.20
The Diffie Hellman Group used by the security association of the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cDiffHellmanGrp  

h3cIPSecTunOutSaEncryptAlgo 1.3.6.1.4.1.2011.10.2.7.1.1.1.21
The encryption algorithm used by the outbound security association of the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cEncryptAlgo  

h3cIPSecTunOutSaAhAuthAlgo 1.3.6.1.4.1.2011.10.2.7.1.1.1.22
The authentication algorithm used by the outbound authentication header (AH) security association of the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cAuthAlgo  

h3cIPSecTunOutSaEspAuthAlgo 1.3.6.1.4.1.2011.10.2.7.1.1.1.23
The authentication algorithm used by the outbound encapsulation security protocol(ESP) security association of the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cAuthAlgo  

h3cIPSecTunPolicyName 1.3.6.1.4.1.2011.10.2.7.1.1.1.24
The policy name used by this IPSec tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

h3cIPSecTunPolicyNum 1.3.6.1.4.1.2011.10.2.7.1.1.1.25
The sequence number of policy used by this IPSec tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cIPSecTunStatus 1.3.6.1.4.1.2011.10.2.7.1.1.1.26
The status of the IPSec Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), ready(2), rekeyed(3), closed(4)  

h3cIPSecTunnelStatTable 1.3.6.1.4.1.2011.10.2.7.1.2
The IPSec Phase-2 Tunnel Statistics Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cIPSecTunnelStatEntry

h3cIPSecTunnelStatEntry 1.3.6.1.4.1.2011.10.2.7.1.2.1
Information about h3cIPSecTunnelStatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cIPSecTunnelStatEntry  

h3cIPSecTunInOctets 1.3.6.1.4.1.2011.10.2.7.1.2.1.1
The total number of octets received by this IPSec Phase-2 Tunnel. This value is accumulated BEFORE determining whether or not the packet should be decompressed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecTunInDecompOctets 1.3.6.1.4.1.2011.10.2.7.1.2.1.2
The total number of decompressed octets received by this IPSec Phase-2 Tunnel. This value is accumulated AFTER the packet is decompressed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecTunInPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.3
The total number of packets received by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecTunInDropPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.4
The total number of packets dropped during receiving process by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecTunInReplayDropPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.5
The total number of packets dropped during receiving process due to Anti-Replay process by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunInAuthFails 1.3.6.1.4.1.2011.10.2.7.1.2.1.6
The total number of inbound authentication's which ended in failure by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunInDecryptFails 1.3.6.1.4.1.2011.10.2.7.1.2.1.7
The total number of inbound decryption's which ended in failure by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunOutOctets 1.3.6.1.4.1.2011.10.2.7.1.2.1.8
The total number of octets sent by this IPSec Phase-2 Tunnel. This value is accumulated AFTER determining whether or not the packet should be compressed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecTunOutUncompOctets 1.3.6.1.4.1.2011.10.2.7.1.2.1.9
The total number of uncompressed octets sent by this IPSec Phase-2 Tunnel.This value is accumulated BEFORE the packet is compressed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecTunOutPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.10
The total number of packets sent by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecTunOutDropPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.11
The total number of packets dropped during sending process by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecTunOutEncryptFails 1.3.6.1.4.1.2011.10.2.7.1.2.1.12
The total number of outbound encryption's which ended in failure by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunNoMemoryDropPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.13
The total number of packets dropped due to no enough memory by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunQueueFullDropPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.14
The total number of packets dropped due to queue full by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunInvalidLenDropPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.15
The total number of packets dropped due to invalid length packet by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunTooLongDropPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.16
The total number of packets dropped due to too long packet by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTunInvalidSaDropPkts 1.3.6.1.4.1.2011.10.2.7.1.2.1.17
The total number of packets dropped due to invalid SA by this IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecSaTable 1.3.6.1.4.1.2011.10.2.7.1.3
The IPSec Phase-2 Security Protection Index Table. This table contains an entry for each active and expiring security association.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cIPSecSaEntry

h3cIPSecSaEntry 1.3.6.1.4.1.2011.10.2.7.1.3.1
Information about h3cIPSecSaTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cIPSecSaEntry  

h3cIPSecSaIndex 1.3.6.1.4.1.2011.10.2.7.1.3.1.1
The number of the Sa associated with the Phase-2 Tunnel Table. The value of this index is a number which begins at one and is incremented with each Sa associated with an IPSec Phase-2 Tunnel. The value of this object will wrap at 2,147,483,647.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cIPSecSaDirection 1.3.6.1.4.1.2011.10.2.7.1.3.1.2
The direction of the SA.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER in(1), out(2)  

h3cIPSecSaValue 1.3.6.1.4.1.2011.10.2.7.1.3.1.3
The value of the SPI.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

h3cIPSecSaProtocol 1.3.6.1.4.1.2011.10.2.7.1.3.1.4
The security protocol of the SA.
Status: current Access: read-only
OBJECT-TYPE    
  H3cSaProtocol  

h3cIPSecSaEncryptAlgo 1.3.6.1.4.1.2011.10.2.7.1.3.1.5
The encryption algorithm used by the security association of the IPSec Phase-2 Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  H3cEncryptAlgo  

h3cIPSecSaAuthAlgo 1.3.6.1.4.1.2011.10.2.7.1.3.1.6
The authentication algorithm used by the SA.
Status: current Access: read-only
OBJECT-TYPE    
  H3cAuthAlgo  

h3cIPSecSaStatus 1.3.6.1.4.1.2011.10.2.7.1.3.1.7
The status of the SA.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), expiring(2)  

h3cIPSecTrafficTable 1.3.6.1.4.1.2011.10.2.7.1.4
The IPSec Phase-2 Tunnel Traffic Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cIPSecTrafficEntry

h3cIPSecTrafficEntry 1.3.6.1.4.1.2011.10.2.7.1.4.1
Information about h3cIPSecTrafficTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cIPSecTrafficEntry  

h3cIPSecTrafficLocalType 1.3.6.1.4.1.2011.10.2.7.1.4.1.1
The type of local peer. Possible values are: a single IP address, or an IP address range, or an IP subnet.
Status: current Access: read-only
OBJECT-TYPE    
  H3cTrafficType  

h3cIPSecTrafficLocalAddr1 1.3.6.1.4.1.2011.10.2.7.1.4.1.2
The first specification of local peer's IP address. If the local peer type is single IP address, then this is the value of the IP address. If the local peer type is IP subnet, then this is the value of the subnet. If the local peer type is IP address range, then this is the value of beginning IP address of the range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

h3cIPSecTrafficLocalAddr2 1.3.6.1.4.1.2011.10.2.7.1.4.1.3
The second specification of local peer's IP address. If the local peer type is single IP address, then this is the value of the IP address. If the local peer type is IP subnet, then this is the value of the subnet mask. If the local peer type is IP address range, then this is the value of ending IP address of the range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

h3cIPSecTrafficLocalProtocol 1.3.6.1.4.1.2011.10.2.7.1.4.1.4
The protocol number of the local peer's traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

h3cIPSecTrafficLocalPort 1.3.6.1.4.1.2011.10.2.7.1.4.1.5
The port number of the local peer's traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

h3cIPSecTrafficRemoteType 1.3.6.1.4.1.2011.10.2.7.1.4.1.6
The type of remote peer. Possible values are: a single IP address, or an IP address range, or an IP subnet.
Status: current Access: read-only
OBJECT-TYPE    
  H3cTrafficType  

h3cIPSecTrafficRemoteAddr1 1.3.6.1.4.1.2011.10.2.7.1.4.1.7
The first specification of remote peer's IP address. If the remote peer type is single IP address, then this is the value of the IP address. If the remote peer type is IP subnet, then this is the value of the subnet. If the remote peer type is IP address range, then this is the value of beginning IP address of the range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

h3cIPSecTrafficRemoteAddr2 1.3.6.1.4.1.2011.10.2.7.1.4.1.8
Single IP address, then this is the value of the IP address. If the remote peer type is IP subnet, then this is the value of the subnet mask. If the remote peer type is IP address range, then this is the value of ending IP address of the range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

h3cIPSecTrafficRemoteProtocol 1.3.6.1.4.1.2011.10.2.7.1.4.1.9
The protocol number of the remote peer's traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

h3cIPSecTrafficRemotePort 1.3.6.1.4.1.2011.10.2.7.1.4.1.10
The port number of the remote peer's traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

h3cIPSecGlobalStats 1.3.6.1.4.1.2011.10.2.7.1.5
OBJECT IDENTIFIER    

h3cIPSecGlobalActiveTunnels 1.3.6.1.4.1.2011.10.2.7.1.5.1
The total number of currently active IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

h3cIPSecGlobalActiveSas 1.3.6.1.4.1.2011.10.2.7.1.5.2
The total number of currently active or expiring IPSec Phase-2 SA.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

h3cIPSecGlobalInOctets 1.3.6.1.4.1.2011.10.2.7.1.5.3
The total number of octets received by all current and previous IPSec Phase-2 Tunnels. This value is accumulated BEFORE determining whether or not the packet should be decompressed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecGlobalInDecompOctets 1.3.6.1.4.1.2011.10.2.7.1.5.4
The total number of decompressed octets received by all current and previous IPSec Phase-2 Tunnels. This value is accumulated AFTER the packet is decompressed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecGlobalInPkts 1.3.6.1.4.1.2011.10.2.7.1.5.5
The total number of packets received by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecGlobalInDrops 1.3.6.1.4.1.2011.10.2.7.1.5.6
The total number of packets dropped during receiving process by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecGlobalInReplayDrops 1.3.6.1.4.1.2011.10.2.7.1.5.7
The total number of packets dropped during receiving process due to Anti-Replay process by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalInAuthFails 1.3.6.1.4.1.2011.10.2.7.1.5.8
The total number of inbound authentication's which ended in failure by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalInDecryptFails 1.3.6.1.4.1.2011.10.2.7.1.5.9
The total number of inbound decryption's which ended in failure by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalOutOctets 1.3.6.1.4.1.2011.10.2.7.1.5.10
The total number of octets sent by all current and previous IPSec Phase-2 Tunnels. This value is accumulated AFTER determining whether or not the packet should be compressed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecGlobalOutUncompOctets 1.3.6.1.4.1.2011.10.2.7.1.5.11
The total number of uncompressed octets sent by all current and previous IPSec Phase-2 Tunnels. This value is accumulated BEFORE the packet is compressed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecGlobalOutPkts 1.3.6.1.4.1.2011.10.2.7.1.5.12
The total number of packets sent by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecGlobalOutDrops 1.3.6.1.4.1.2011.10.2.7.1.5.13
The total number of packets dropped during sending process by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

h3cIPSecGlobalOutEncryptFails 1.3.6.1.4.1.2011.10.2.7.1.5.14
The total number of outbound encryption's which ended in failure by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalNoMemoryDropPkts 1.3.6.1.4.1.2011.10.2.7.1.5.15
The total number of packets dropped due to no enough memory by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalNoFindSaDropPkts 1.3.6.1.4.1.2011.10.2.7.1.5.16
The total number of packets dropped due to not find SA by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalQueueFullDropPkts 1.3.6.1.4.1.2011.10.2.7.1.5.17
The total number of packets dropped due to queue full by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalInvalidLenDropPkts 1.3.6.1.4.1.2011.10.2.7.1.5.18
The total number of packets dropped due to invalid packet length by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalTooLongDropPkts 1.3.6.1.4.1.2011.10.2.7.1.5.19
The total number of packets dropped due to too long packet by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecGlobalInvalidSaDropPkts 1.3.6.1.4.1.2011.10.2.7.1.5.20
The total number of packets dropped due to invalid SA by all current and previous IPSec Phase-2 Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cIPSecTrapObject 1.3.6.1.4.1.2011.10.2.7.1.6
OBJECT IDENTIFIER    

h3cIPSecPolicyName 1.3.6.1.4.1.2011.10.2.7.1.6.1
The IPSec policy name with a trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

h3cIPSecPolicySeqNum 1.3.6.1.4.1.2011.10.2.7.1.6.2
The IPSec policy sequence number with a trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

h3cIPSecPolicySize 1.3.6.1.4.1.2011.10.2.7.1.6.3
The number of IPSec policies with a trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

h3cIPSecSpiValue 1.3.6.1.4.1.2011.10.2.7.1.6.4
The SPI value associated with a trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

h3cIPSecTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7
OBJECT IDENTIFIER    

h3cIPSecTrapGlobalCntl 1.3.6.1.4.1.2011.10.2.7.1.7.1
Indicates whether all IPSec traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecTunnelStartTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.2
Indicates whether h3cIPSecTunnelStart traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecTunnelStopTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.3
Indicates whether h3cIPSecTunnelStop traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecNoSaTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.4
Indicates whether h3cIPSecNoSaFailure traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecAuthFailureTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.5
Indicates whether h3cIPSecAuthFailFailure traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecEncryFailureTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.6
Indicates whether h3cIPSecEncryFailFailure traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecDecryFailureTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.7
Indicates whether h3cIPSecDecryFailFailure traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecInvalidSaTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.8
Indicates whether h3cIPSec Invalid Sa Failure traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecPolicyAddTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.9
Indicates whether h3cIPSecPolicyAdd traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecPolicyDelTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.10
Indicates whether h3cIPSecPolicyDel traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecPolicyAttachTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.11
Indicates whether h3cIPSecPolicyAttach traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecPolicyDetachTrapCntl 1.3.6.1.4.1.2011.10.2.7.1.7.12
Indicates whether h3cIPSecPolicyDetach traps should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  H3cTrapStatus  

h3cIPSecTrap 1.3.6.1.4.1.2011.10.2.7.1.8
OBJECT IDENTIFIER    

h3cIPSecNotifications 1.3.6.1.4.1.2011.10.2.7.1.8.1
OBJECT IDENTIFIER    

h3cIPSecTunnelStart 1.3.6.1.4.1.2011.10.2.7.1.8.1.1
This notification is generated when an IPSec Phase-2 Tunnel is created.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecTunnelStop 1.3.6.1.4.1.2011.10.2.7.1.8.1.2
This notification is generated when an IPSec Phase-2 Tunnel is deleted.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecNoSaFailure 1.3.6.1.4.1.2011.10.2.7.1.8.1.3
This notification is generated when an IPSec Phase-2 non-existent SA error occurs.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecAuthFailFailure 1.3.6.1.4.1.2011.10.2.7.1.8.1.4
This notification is generated when the IPSec phase-2 authentication failure occurs.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecEncryFailFailure 1.3.6.1.4.1.2011.10.2.7.1.8.1.5
This notification is generated when the IPSec phase-2 tunnel has an encrypting failure.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecDecryFailFailure 1.3.6.1.4.1.2011.10.2.7.1.8.1.6
This notification is generated when the IPSec phase-2 tunnel has a decrypting failure.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecInvalidSaFailure 1.3.6.1.4.1.2011.10.2.7.1.8.1.7
This notification is generated when the IPSec phase-2 invalid SA failure occurs.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecPolicyAdd 1.3.6.1.4.1.2011.10.2.7.1.8.1.8
This notification is generated when an IPSec policy is added.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecPolicyDel 1.3.6.1.4.1.2011.10.2.7.1.8.1.9
This notification is generated when an IPSec policy is deleted.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecPolicyAttach 1.3.6.1.4.1.2011.10.2.7.1.8.1.10
This notification is generated when an IPSec policy is attached with one interface.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecPolicyDetach 1.3.6.1.4.1.2011.10.2.7.1.8.1.11
This notification is generated when an IPSec policy is detached with one interface.
Status: current Access: read-write
NOTIFICATION-TYPE    

h3cIPSecConformance 1.3.6.1.4.1.2011.10.2.7.2
OBJECT IDENTIFIER    

h3cIPSecCompliances 1.3.6.1.4.1.2011.10.2.7.2.1
OBJECT IDENTIFIER    

h3cIPSecGroups 1.3.6.1.4.1.2011.10.2.7.2.2
OBJECT IDENTIFIER    

h3cIPSecCompliance 1.3.6.1.4.1.2011.10.2.7.2.1.1
Status: current Access: read-write
MODULE-COMPLIANCE    

h3cIPSecTunnelTableGroup 1.3.6.1.4.1.2011.10.2.7.2.2.1
The group contains the IPSec tunnel's property information.
Status: current Access: read-write
OBJECT-GROUP    

h3cIPSecTunnelStatGroup 1.3.6.1.4.1.2011.10.2.7.2.2.2
The group contains the IPSec tunnel's statistic information.
Status: current Access: read-write
OBJECT-GROUP    

h3cIPSecSaGroup 1.3.6.1.4.1.2011.10.2.7.2.2.3
The group contains the SA's property information.
Status: current Access: read-write
OBJECT-GROUP    

h3cIPSecTrafficTableGroup 1.3.6.1.4.1.2011.10.2.7.2.2.4
The group contains the property information of the data flow protected by IPSec tunnel.
Status: current Access: read-write
OBJECT-GROUP    

h3cIPSecGlobalStatsGroup 1.3.6.1.4.1.2011.10.2.7.2.2.5
The group contains all of the IPSec tunnel's statistic information.
Status: current Access: read-write
OBJECT-GROUP    

h3cIPSecTrapObjectGroup 1.3.6.1.4.1.2011.10.2.7.2.2.6
The group contains all of trap objects of IPSec tunnels.
Status: current Access: read-write
OBJECT-GROUP    

h3cIPSecTrapCntlGroup 1.3.6.1.4.1.2011.10.2.7.2.2.7
The group contains all of trap switches of IPSec tunnels.
Status: current Access: read-write
OBJECT-GROUP    

h3cIPSecTrapGroup 1.3.6.1.4.1.2011.10.2.7.2.2.8
The group contains all of trap of IPSec tunnels.
Status: current Access: read-write
NOTIFICATION-GROUP