H3C-EPON-UNI-MIB

File: H3C-EPON-UNI-MIB.mib (64068 bytes)

Imported modules

HUAWEI-3COM-OID-MIB IF-MIB SNMPv2-SMI
SNMPv2-TC

Imported symbols

h3cEpon ifIndex ifDescr
Integer32 Unsigned32 IpAddress
OBJECT-TYPE MODULE-IDENTITY NOTIFICATION-TYPE
MacAddress TruthValue RowStatus

Defined Types

H3cEponUniSysManEntry  
SEQUENCE    
  h3cEponUniIndex Integer32
  h3cEponUniDescr OCTET STRING
  h3cEponUniAdminStatus INTEGER
  h3cEponUniMdi INTEGER
  h3cEponUniPriority Integer32
  h3cEponUniVlanType INTEGER
  h3cEponUniAccessVlan Integer32
  h3cEponUniTrunkPvid INTEGER
  h3cEponUniVLANTrunkAllowListLow OCTET STRING
  h3cEponUniVLANTrunkAllowListHigh OCTET STRING
  h3cEponUniInboundLineRate Integer32
  h3cEponUniOutboundLineRate Integer32
  h3cEponUniFlowControl TruthValue
  h3cEponUniSpeed INTEGER
  h3cEponUniDuplex INTEGER
  h3cEponUniVlanVPNStatus TruthValue
  h3cEponUniCountReset INTEGER
  h3cEponUniPortIsolate INTEGER
  h3cEponUniVlanConfiguration OCTET STRING
  h3cEponUniAutoNegotiation INTEGER
  h3cEponUniRestartAutoNeg INTEGER
  h3cEponUniLinkStatus INTEGER
  h3cEponUniInterfaceType INTEGER
  h3cEponUniVitualCableTest INTEGER
  h3cEponUniVCTCableStatus INTEGER
  h3cEponUniVCTCableLength Integer32
  h3cEponUniVCTImpedanceMismatch INTEGER
  h3cEponUniVCTPairSkew Integer32
  h3cEponUniVCTPairSwap INTEGER
  h3cEponUniVCTPolaritySwap INTEGER
  h3cEponUniVCTInsertionLoss Integer32
  h3cEponUniVCTReturnLoss Integer32
  h3cEponUniVCTNearendCrosstalk Integer32

H3cEponUniCountEntry  
SEQUENCE    
  h3cEponUniInStatsPkts Unsigned32
  h3cEponUniInStatsUnicastPkts Unsigned32
  h3cEponUniInStatsBroadcastPkts Unsigned32
  h3cEponUniInStatsMulticastPkts Unsigned32
  h3cEponUniInPausePkts Unsigned32
  h3cEponUniInTotalErrors Unsigned32
  h3cEponUniInStatsCRCAlignErrors Unsigned32
  h3cEponUniInStatsUndersizePkts Unsigned32
  h3cEponUniInStatsOversizePkts Unsigned32
  h3cEponUniInErrorbyOther Unsigned32
  h3cEponUniOutStatsPkts Unsigned32
  h3cEponUniOutStatsUnicastPkts Unsigned32
  h3cEponUniOutStatsBroadcastPkts Unsigned32
  h3cEponUniOutStatsMulticastPkts Unsigned32
  h3cEponUniOutStatsPausePkts Unsigned32
  h3cEponUniOutTotalErrors Unsigned32
  h3cEponUniOutStatsCollisions Unsigned32
  h3cEponUniOutDelayExceededDiscards Unsigned32
  h3cEponUniOutErrorbyOther Unsigned32
  h3cEponUniOutDroppedFrames Unsigned32

H3cEponUniIgmpInfoEntry  
SEQUENCE    
  h3cEponUniMacIndex Integer32
  h3cEponUniIgmpMacAddress MacAddress
  h3cEponUniIgmpVlanId Integer32

H3cEponUniPortPolicyEntry  
SEQUENCE    
  h3cEponUniPortPolicyStatus INTEGER
  h3cEponUniPortPolicyCir Integer32
  h3cEponUniPortPolicyBucketDepth Integer32
  h3cEponUniPortPolicyExtraBurst Integer32
  h3cEponUniPortPolicyInboundCir Integer32
  h3cEponUniPortPolicyInboundBucketDepth Integer32
  h3cEponUniPortPolicyInboundExtraBurst Integer32
  h3cEponUniPortPolicyOutboundCir Integer32
  h3cEponUniPortPolicyOutboundPir Integer32

H3cEponUniMulticastEntry  
SEQUENCE    
  h3cEponUniMulticastGroupNumber Integer32
  h3cEponUniMulticastVlanList OCTET STRING
  h3cEponUniMulticastStripStatus INTEGER
  h3cEponUniMulticastFastleave TruthValue

H3cEponUniTechAbilityEntry  
SEQUENCE    
  h3cEponUniLocalTechAbility OCTET STRING
  h3cEponUniAdvertisedTechAbility OCTET STRING

H3cEponUniMulticastControlEntry  
SEQUENCE    
  h3cEponUniMulticastVlanIndex Integer32
  h3cEponUniMulticastAddressList OCTET STRING
  h3cEponUniMulticastAccessRule INTEGER
  h3cEponUniMulticastChannelLimit Integer32
  h3cEponUniMulticastPreTimeSlice Integer32
  h3cEponUniMulticastPreTimes Integer32
  h3cEponUniMulticastPreInterval Integer32
  h3cEponUniMulticastRowStatus RowStatus
  h3cEponUniMulticastIndex INTEGER
  h3cEponUniMulticastSourceIpList OCTET STRING
  h3cEponUniMulticastResetInterval Integer32

H3cEponUniQosIndexNextEntry  
SEQUENCE    
  h3cEponUniQosConfIndexNext Integer32

H3cEponUniQosConfEntry  
SEQUENCE    
  h3cEponUniQosConfIndex Integer32
  h3cEponUniQosConfRuleIndexNext Integer32
  h3cEponUniQosConfMappedQueue Integer32
  h3cEponUniQosConfMarkedPriority Integer32
  h3cEponUniQosConfRowStatus RowStatus

H3cEponUniQosRuleEntry  
SEQUENCE    
  h3cEponUniQosRuleIndex Integer32
  h3cEponUniQosRuleSelector INTEGER
  h3cEponUniQosRuleValue Integer32
  h3cEponUniQosRuleMacAddress MacAddress
  h3cEponUniQosRuleOperator INTEGER
  h3cEponUniQosRuleRowStatus RowStatus

H3cEponUniMirrorGroupEntry  
SEQUENCE    
  h3cEponUniMirrorGroupID Integer32
  h3cEponUniMirrorInboundPortList OCTET STRING
  h3cEponUniMirrorOutboundPortList OCTET STRING
  h3cEponUniMonitorPort Integer32
  h3cEponUniMirrorRowStatus RowStatus

H3cEponUniMirrorGroupIdNextEntry  
SEQUENCE    
  h3cEponUniMirrorGroupIDNext Integer32

H3cEponUniMulticastCtrlInfoEntry  
SEQUENCE    
  h3cEponUniMultActVlan Integer32
  h3cEponUniMultActAddress IpAddress
  h3cEponUniMultActAccessRule INTEGER
  h3cEponUniMultActPreTimes Integer32
  h3cEponUniMultActPreRemain Integer32

H3cEponUniMulticastIndexNextEntry  
SEQUENCE    
  h3cEponUniMulticastConfIndexNext Integer32

Defined Values

h3cEponUni 1.3.6.1.4.1.2011.10.2.42.5
The objects in this MIB module are used to manage and display current configuration of UNI (user network interface) which is based on the ONU(Optical Network Unit).
MODULE-IDENTITY    

h3cEponUniSysMan 1.3.6.1.4.1.2011.10.2.42.5.1
OBJECT IDENTIFIER    

h3cEponUniSysManTable 1.3.6.1.4.1.2011.10.2.42.5.1.1
This table defines several UNI system parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniSysManEntry

h3cEponUniSysManEntry 1.3.6.1.4.1.2011.10.2.42.5.1.1.1
The entry of h3cEponUniSysManTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniSysManEntry  

h3cEponUniIndex 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.1
The index value which uniquely identifies the FE(fast Ethernet) interface of the ONU.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

h3cEponUniDescr 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.2
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware and software.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

h3cEponUniAdminStatus 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.3
The desired state of the user network interface. When a managed system initializes, all user network interfaces start with down(2) state. The testing(3)state indicates that no operational packets can be passed. As a result of either explicit management action or per configuration information retained by the managed system, h3cEponUniAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

h3cEponUniMdi 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.4
Type of the line connected to UNI interface: mdi-ii(straight-through cable), mdi-x (crossover cable), mdi-auto (auto-sensing).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mdi-ii(1), mdi-x(2), mdi-auto(3)  

h3cEponUniPriority 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.5
The priority of user network interface. If the value is larger, the priority will be higher.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

h3cEponUniVlanType 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.6
UNI vlan types.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER vlantrunk(1), access(2), hybrid(3), untagged(4), transparent(5), doubletagged(6), tag(7), translation(8)  

h3cEponUniAccessVlan 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.7
The vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4094  

h3cEponUniTrunkPvid 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.8
PVID(port vlan ID), the vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

h3cEponUniVLANTrunkAllowListLow 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.9
Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans. the vlan is not allowed if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

h3cEponUniVLANTrunkAllowListHigh 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.10
Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 2049 through 2056, the second octet specifying vlans 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered vlan, and the least significant bit represents the lowest numbered vlan. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans; the vlan is not allowed if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

h3cEponUniInboundLineRate 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.11
The value of the inbound line-rate. measured with kbps. The upper limit of the line-rate is the value of h3cEponUniLineRateMax in the entry. It must be multiple of the value of h3cEponUniLineRateStep. The default value of h3cEponUniLineRate is the value of h3cEponUniLineRateMax.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniOutboundLineRate 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.12
The value of the outbound line-rate. measured with kbps. The upper limit of the line-rate is the value of h3cEponUniLineRateMax in the entry. It must be multiple of the value of h3cEponUniLineRateStep. The default value of h3cEponUniLineRate is the value of h3cEponUniLineRateMax.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniFlowControl 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.13
Flow control status. true(1) - Flow control status enable. false(2) - Flow control status disable.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponUniSpeed 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.14
User network interface speed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(0), s10M(10), s100M(100), s1000M(1000), s10000M(10000), s24000M(24000)  

h3cEponUniDuplex 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.15
User network interface mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER full(1), half(2), auto(3)  

h3cEponUniVlanVPNStatus 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.16
vlan VPN status. true(1) - vlan VPN status enable. false(2) - vlan VPN disable.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponUniCountReset 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.17
Reset the counter which is about packets of the interface, then the counter will change to zero. There is no sense in reading this object.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1)  

h3cEponUniPortIsolate 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.18
enable - enable UNI port isolate setting. disable - disable UNI port isolate setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

h3cEponUniVlanConfiguration 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.23
The vlan configuration of the related vlan mode. Transparent vlan mode: h3cEponUniVlanConfiguration is a zero length string. Tag vlan mode: the first four octets were the tag assigned to untagged frames received on UNI, including TPID, VID,CFI and priority. Translation vlan mode: the first four octets were the old tag (including TPID, VID, CFI and priority), which is replaced by the new tag(including TPID, VID, CFI and priority), the second four octets.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

h3cEponUniAutoNegotiation 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.25
enable - enable auto negotiation. disable - disable auto negotiation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

h3cEponUniRestartAutoNeg 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.26
Force to restart the auto negotiation process.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER autoNegotiation(1)  

h3cEponUniLinkStatus 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.29
The link status of UNI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

h3cEponUniInterfaceType 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.30
UNI interface type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER gigabitethernetport(1), fastethernetport(2), voipport(3), e1port(4)  

h3cEponUniVitualCableTest 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.31
True(1): Virtual cable test enable. False(2): Virtual cable test disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

h3cEponUniVCTCableStatus 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.32
Get the cable status. Normal(1),cable is normal. Abnormal(2),cable is abnormal. AbnormalOpen(3),cable is abnormal because of open circuit. AbnormalShort(4),cable is abnormal because of short circuit. Failure(5),cable is abnormal because of testing failure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), abnormal(2), abnormalOpen(3), abnormalShort(4), failure(5)  

h3cEponUniVCTCableLength 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.33
Get the cable length. When h3cEponUniVCTCableStatus is normal, the node stands for the length from the UNI port to the port opposite. When h3cEponUniVCTCableStatus is abnormal, it stands for the lengh from the UNI port to the failure place. Unit:meter(m).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniVCTImpedanceMismatch 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.34
Get the cable impedance. Not-support(1),the UNI port does not support this function. True(2),impedance match. False(3),impedance mismatch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-support(1), true(2), false(3)  

h3cEponUniVCTPairSkew 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.35
Get the symmetry of cable. If the function is not supported , the default value 0 will be returned. Unit:nanosecond(ns).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniVCTPairSwap 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.36
NotSupport(1),the UNI port does not support this function. True(2),pair swap. False(3),not pair swap.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(1), true(2), false(3)  

h3cEponUniVCTPolaritySwap 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.37
NotSupport(1),the UNI port does not support this function. True(2),polarity swap. False(3),not polarity swap.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(1), true(2), false(3)  

h3cEponUniVCTInsertionLoss 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.38
If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniVCTReturnLoss 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.39
If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniVCTNearendCrosstalk 1.3.6.1.4.1.2011.10.2.42.5.1.1.1.40
If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniCountTable 1.3.6.1.4.1.2011.10.2.42.5.1.2
A list of interface counter about frames entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniCountEntry

h3cEponUniCountEntry 1.3.6.1.4.1.2011.10.2.42.5.1.2.1
An entry containing management information applicable to a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniCountEntry  

h3cEponUniInStatsPkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.1
The total number of frames (including bad frames, broadcast frames, and multicast frames) received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInStatsUnicastPkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.2
The total number of good frames received that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInStatsBroadcastPkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.3
The total number of good frames received that are directed to the broadcast address. Note that this does not include multicast frames.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInStatsMulticastPkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.4
The total number of good frames received that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInPausePkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.5
A count of MAC Control frames received on this interface by the pause(flow control) operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInTotalErrors 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.6
Total count of the error frames received on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInStatsCRCAlignErrors 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.7
The total number of frames received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInStatsUndersizePkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.8
The total number of frames received that are less than 64 octets long (excluding framing bits, but including FCS octets) and are otherwise well formed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInStatsOversizePkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.9
The total number of frames received that are longer than 1518 octets (excluding framing bits, but including FCS octets) and are otherwise well formed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniInErrorbyOther 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.10
The total number of error frames received on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutStatsPkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.11
The total number of frames (including bad frames, broadcast frames, and multicast frames) sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutStatsUnicastPkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.12
The total number of good frames sent that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutStatsBroadcastPkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.13
The total number of good frames sent that are directed to the broadcast address. Note that this does not include multicast frames.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutStatsMulticastPkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.14
The total number of good frames sent that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutStatsPausePkts 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.15
The total number of MAC control frames sent on this interface by the pause operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutTotalErrors 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.16
The total number of error frames sent on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutStatsCollisions 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.17
The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment could. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutDelayExceededDiscards 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.18
The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutErrorbyOther 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.19
The total number of other error frames sent on this interface. Other error frames means the error frames out of collision frames and excessive delayed frames.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniOutDroppedFrames 1.3.6.1.4.1.2011.10.2.42.5.1.2.1.20
The total number of frames dropped because of buffer failure.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

h3cEponUniIgmpInfoTable 1.3.6.1.4.1.2011.10.2.42.5.1.3
This table stores igmp information of UNI interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniIgmpInfoEntry

h3cEponUniIgmpInfoEntry 1.3.6.1.4.1.2011.10.2.42.5.1.3.1
The entry of h3cEponUniIgmpInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniIgmpInfoEntry  

h3cEponUniMacIndex 1.3.6.1.4.1.2011.10.2.42.5.1.3.1.1
The index uniquely identifies the igmp information in current UNI interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

h3cEponUniIgmpMacAddress 1.3.6.1.4.1.2011.10.2.42.5.1.3.1.2
A 6-octet read-only value carrying the individual MAC address indicates which igmp group the UNI interface belonging to.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

h3cEponUniIgmpVlanId 1.3.6.1.4.1.2011.10.2.42.5.1.3.1.3
An integer range from 1 to 4094 indicates the vlan which the igmp Mac address has joined in.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..4094  

h3cEponUniParaMan 1.3.6.1.4.1.2011.10.2.42.5.1.4
OBJECT IDENTIFIER    

h3cEponUniLineRateMax 1.3.6.1.4.1.2011.10.2.42.5.1.4.1
The maximum value of the line-rate(kbps) that user network interface can be set.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniLineRateStep 1.3.6.1.4.1.2011.10.2.42.5.1.4.2
The step of line-rate(kbps).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniNumberOnOnu 1.3.6.1.4.1.2011.10.2.42.5.1.4.3
The user network interface number on ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniScalarGroup 1.3.6.1.4.1.2011.10.2.42.5.1.5
OBJECT IDENTIFIER    

h3cEponUniPortPolicyTable 1.3.6.1.4.1.2011.10.2.42.5.1.6
UNI port policy configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniPortPolicyEntry

h3cEponUniPortPolicyEntry 1.3.6.1.4.1.2011.10.2.42.5.1.6.1
The entry of h3cEponUniPortPolicyTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniPortPolicyEntry  

h3cEponUniPortPolicyStatus 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.1
enable - enable UNI upstream port policing. disable - disable UNI upstream port policing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

h3cEponUniPortPolicyCir 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.2
The committed information rate, ranging from 1 to 102400, measured in kbps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniPortPolicyBucketDepth 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.3
The depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniPortPolicyExtraBurst 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.4
The extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniPortPolicyInboundCir 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.5
The inbound committed information rate, measured in kbps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniPortPolicyInboundBucketDepth 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.6
The inbound depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniPortPolicyInboundExtraBurst 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.7
The inbound extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniPortPolicyOutboundCir 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.8
The outbound committed information rate, stepped by 64, measured in kbps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniPortPolicyOutboundPir 1.3.6.1.4.1.2011.10.2.42.5.1.6.1.9
The outbound peak information rate, stepped by 64, measured in kbps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastTable 1.3.6.1.4.1.2011.10.2.42.5.1.7
UNI multicast configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniMulticastEntry

h3cEponUniMulticastEntry 1.3.6.1.4.1.2011.10.2.42.5.1.7.1
The entry of h3cEponUniPortPolicyTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniMulticastEntry  

h3cEponUniMulticastGroupNumber 1.3.6.1.4.1.2011.10.2.42.5.1.7.1.1
The allowed multicast group number that can be handled at the same time by UNI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastVlanList 1.3.6.1.4.1.2011.10.2.42.5.1.7.1.2
The multicast vlan list. The first two octets of the string represent the first VLAN ID; the second two octets of the string represent the second VLAN ID, and so on. It is a zero length string by default.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

h3cEponUniMulticastStripStatus 1.3.6.1.4.1.2011.10.2.42.5.1.7.1.3
true - strip the vlan tag of multicast packet. false - does not strip the vlan tag of multicast packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

h3cEponUniMulticastFastleave 1.3.6.1.4.1.2011.10.2.42.5.1.7.1.4
true(1) - fast leave of IGMP enable on ONU. false(2) - fast leave of IGMP disable on ONU.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponUniTechAbilityTable 1.3.6.1.4.1.2011.10.2.42.5.1.8
UNI multicast configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniTechAbilityEntry

h3cEponUniTechAbilityEntry 1.3.6.1.4.1.2011.10.2.42.5.1.8.1
The entry of h3cEponUniTechAbilityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniTechAbilityEntry  

h3cEponUniLocalTechAbility 1.3.6.1.4.1.2011.10.2.42.5.1.8.1.1
The local port capabilities of the UNI. Each two octets stand for a capability of UNI: the first two octets represent one capability and the second two octets represent another capability, and so on. The capabilities list: 1 - undefined, 2 - initializing, true ability not yet known, 14 - 10BASE-T, 142 - full duplex 10BASE-T, 23 - 100BASE-T4, 25 - 100BASE-TX, 252 - full duplex 100BASE-TX, 312 - PAUSE operation for full duplex links, 313 - asymmetric PAUSE operation for full duplex links, 314 - symmetric PAUSE operation for full duplex links, 32 - 100BASE-T2, 322 - full duplex 100BASE-T2, 36 - 1000BASE-X, 362 - full duplex 1000BASE-X, 40 - 1000BASE-T UTP PHY, 402 - full duplex 1000BASE-T UTP PHY, 37 - remote fault bit 1(RF1), 372 - remote fault bit 2(RF2), 8029 - 802.9ISLAN-16T.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

h3cEponUniAdvertisedTechAbility 1.3.6.1.4.1.2011.10.2.42.5.1.8.1.2
The advertised port capabilities of the UNI. The capabilities list references the description of h3cEponUniLocalTechAbility.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

h3cEponUniMulticastControlTable 1.3.6.1.4.1.2011.10.2.42.5.1.9
UNI multicast control parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniMulticastControlEntry

h3cEponUniMulticastControlEntry 1.3.6.1.4.1.2011.10.2.42.5.1.9.1
The entry of the table h3cEponUniMulticastControlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniMulticastControlEntry  

h3cEponUniMulticastVlanIndex 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.1
The multicast vlan ID.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastAddressList 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.2
The multicast address, each four octets represents a multicast address, the address section ranging from the first four octets to the second four octets, and the like.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

h3cEponUniMulticastAccessRule 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.3
deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER deny(1), permit(2), preview(3)  

h3cEponUniMulticastChannelLimit 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.4
The limitation of multicast preview channel number.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastPreTimeSlice 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.5
The time slice of multicast preview.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastPreTimes 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.6
The number of multicast preview times.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastPreInterval 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.7
The interval between two consecutive previews, measured in minute.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastRowStatus 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.8
The status of this table entry. The active, createAndGo and the destory statuses are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h3cEponUniMulticastIndex 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.9
The index of the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

h3cEponUniMulticastSourceIpList 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.10
This list contains many source ip addresses. Each ip address is contained in four octets.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

h3cEponUniMulticastResetInterval 1.3.6.1.4.1.2011.10.2.42.5.1.9.1.11
The interval is measured in minute. From the last preview limitation is reached, a customer can preview again after this interval is expired.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniQosIndexNextTable 1.3.6.1.4.1.2011.10.2.42.5.1.10
The next index table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniQosIndexNextEntry

h3cEponUniQosIndexNextEntry 1.3.6.1.4.1.2011.10.2.42.5.1.10.1
The entry of the table h3cEponUniQosIndexNextTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniQosIndexNextEntry  

h3cEponUniQosConfIndexNext 1.3.6.1.4.1.2011.10.2.42.5.1.10.1.1
This object contains an appropriate value to be used for h3cEponUniQosConfIndex when creating rows in the h3cEponUniQosConfTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniQosConfTable 1.3.6.1.4.1.2011.10.2.42.5.1.11
UNI Qos configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniQosConfEntry

h3cEponUniQosConfEntry 1.3.6.1.4.1.2011.10.2.42.5.1.11.1
The entry of the table h3cEponUniQosConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniQosConfEntry  

h3cEponUniQosConfIndex 1.3.6.1.4.1.2011.10.2.42.5.1.11.1.1
The rule index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

h3cEponUniQosConfRuleIndexNext 1.3.6.1.4.1.2011.10.2.42.5.1.11.1.2
This object contains an appropriate value to be used for h3cEponUniQosRuleIndex when creating rows in the h3cEponUniQosRuleTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniQosConfMappedQueue 1.3.6.1.4.1.2011.10.2.42.5.1.11.1.3
The queue that the ethernet frames will be mapped.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniQosConfMarkedPriority 1.3.6.1.4.1.2011.10.2.42.5.1.11.1.4
Priority of the ethernet frames to be marked, which compliant with the 802.1D user priority standard.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniQosConfRowStatus 1.3.6.1.4.1.2011.10.2.42.5.1.11.1.5
The status of this table entry. The active, createAndGo and the destory statuses are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h3cEponUniQosRuleTable 1.3.6.1.4.1.2011.10.2.42.5.1.12
Qos sub rule of the UNI.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniQosRuleEntry

h3cEponUniQosRuleEntry 1.3.6.1.4.1.2011.10.2.42.5.1.12.1
The entry of the table h3cEponUniQosRuleTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniQosRuleEntry  

h3cEponUniQosRuleIndex 1.3.6.1.4.1.2011.10.2.42.5.1.12.1.1
The sub rule index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

h3cEponUniQosRuleSelector 1.3.6.1.4.1.2011.10.2.42.5.1.12.1.2
The ethernet frame selector. dstmac - based on destination MAC address. srcmac - based on source MAC address. ethernetpriority - based on ethernet priority. vlanid - based on VLAN ID. ethernettype - based on ethernet type. dstip - based on destination IP address. srcip - based on source IP address. ipprototype - based on IP type(ipv4 or ipv6). ipv4tosdscp - based on IP TOS/DSCP. ipv6 - based IP precedence. srcport - based on layer 4 source port. dstport - based on layer 4 destination port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER dstmac(1), srcmac(2), ethernetpriority(3), vlanid(4), ethernettype(5), dstip(6), srcip(7), ipprototype(8), ipv4tosdscp(9), ipv6precedence(10), srcport(11), dstport(12)  

h3cEponUniQosRuleValue 1.3.6.1.4.1.2011.10.2.42.5.1.12.1.3
The rule value based on the h3cEponUniQosRuleSelector.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniQosRuleMacAddress 1.3.6.1.4.1.2011.10.2.42.5.1.12.1.4
MAC Address.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

h3cEponUniQosRuleOperator 1.3.6.1.4.1.2011.10.2.42.5.1.12.1.5
nervermatch - value never match. equal - field equal to the value. notequal - field not equal to the value. lessthanequal - field less than or equal to the value. greaterthanequal - field greater than or equal to the value. fieldexist - value is ignored if field exists. fieldnotexist - value is ignored if field does not exist. alwaysmatch - value always match.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER nevermatch(1), equal(2), notequal(3), lessthanequal(4), greaterthanequal(5), fieldexist(6), fieldnotexist(7), alwaysmatch(8)  

h3cEponUniQosRuleRowStatus 1.3.6.1.4.1.2011.10.2.42.5.1.12.1.6
The status of this table entry. Only active, createAndGo and the destory are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h3cEponUniMirrorGroupTable 1.3.6.1.4.1.2011.10.2.42.5.1.13
Qos sub rule of the UNI.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniMirrorGroupEntry

h3cEponUniMirrorGroupEntry 1.3.6.1.4.1.2011.10.2.42.5.1.13.1
The entry of the h3cEponUniMirrorGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniMirrorGroupEntry  

h3cEponUniMirrorGroupID 1.3.6.1.4.1.2011.10.2.42.5.1.13.1.1
Epon UNI mirror group ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

h3cEponUniMirrorInboundPortList 1.3.6.1.4.1.2011.10.2.42.5.1.13.1.2
UNI inbound port list. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered UNI, and the least significant bit represents the lowest numbered UNI. Thus, each UNI port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is allowed in the set of ports. the port is not allowed if its bit has a value of '0'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

h3cEponUniMirrorOutboundPortList 1.3.6.1.4.1.2011.10.2.42.5.1.13.1.3
UNI outnbound port list, more infomation reference h3cEponUniMirrorInboundPortList
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

h3cEponUniMonitorPort 1.3.6.1.4.1.2011.10.2.42.5.1.13.1.4
UNI monitor port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

h3cEponUniMirrorRowStatus 1.3.6.1.4.1.2011.10.2.42.5.1.13.1.5
RowStatus, Now support three status: createAndGo, active, destroy.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h3cEponUniMirrorGroupIdNextTable 1.3.6.1.4.1.2011.10.2.42.5.1.14
The next index table, which is used by h3cEponUniMirrorGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniMirrorGroupIdNextEntry

h3cEponUniMirrorGroupIdNextEntry 1.3.6.1.4.1.2011.10.2.42.5.1.14.1
The entry of the table h3cEponUniMirrorGroupIdNextEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniMirrorGroupIdNextEntry  

h3cEponUniMirrorGroupIDNext 1.3.6.1.4.1.2011.10.2.42.5.1.14.1.1
This object contains an appropriate value to be used for h3cEponUniMirrorGroupID when creating rows in the h3cEponUniMirrorGroupTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastCtrlInfoTable 1.3.6.1.4.1.2011.10.2.42.5.1.15
UNI multicast information which is active .
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniMulticastCtrlInfoEntry

h3cEponUniMulticastCtrlInfoEntry 1.3.6.1.4.1.2011.10.2.42.5.1.15.1
The entry of the table h3cEponUniMulticastCtrlInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniMulticastCtrlInfoEntry  

h3cEponUniMultActVlan 1.3.6.1.4.1.2011.10.2.42.5.1.15.1.1
The multicast vlan ID which is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

h3cEponUniMultActAddress 1.3.6.1.4.1.2011.10.2.42.5.1.15.1.2
The multicast address which is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

h3cEponUniMultActAccessRule 1.3.6.1.4.1.2011.10.2.42.5.1.15.1.3
deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER deny(1), permit(2), preview(3)  

h3cEponUniMultActPreTimes 1.3.6.1.4.1.2011.10.2.42.5.1.15.1.4
The number of multicast preview times which is active.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniMultActPreRemain 1.3.6.1.4.1.2011.10.2.42.5.1.15.1.5
The remanent time slice of multicast preview which is active.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniMulticastIndexNextTable 1.3.6.1.4.1.2011.10.2.42.5.1.16
The next index table, which is used by h3cEponUniMulticastControlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponUniMulticastIndexNextEntry

h3cEponUniMulticastIndexNextEntry 1.3.6.1.4.1.2011.10.2.42.5.1.16.1
The entry of the table h3cEponUniMulticastIndexNextEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponUniMulticastIndexNextEntry  

h3cEponUniMulticastConfIndexNext 1.3.6.1.4.1.2011.10.2.42.5.1.16.1.1
This object contains an appropriate value to be used for h3cEponUniMulticastIndex when creating rows in the h3cEponUniMulticastControlTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponUniTrap 1.3.6.1.4.1.2011.10.2.42.5.2
OBJECT IDENTIFIER    

h3cEponUniTrapPrefix 1.3.6.1.4.1.2011.10.2.42.5.2.0
OBJECT IDENTIFIER    

h3cEponUniLinkUpTrap 1.3.6.1.4.1.2011.10.2.42.5.2.0.1
A h3cEponUniLinkUpTrap notification is sent when the UNI up event is detected and the transmitting switch is turned on.
Status: current Access: read-only
NOTIFICATION-TYPE    

h3cEponUniLinkDownTrap 1.3.6.1.4.1.2011.10.2.42.5.2.0.2
A h3cEponUniLinkDownTrap notification is sent when the UNI down event is detected and the transmitting switch is turned on.
Status: current Access: read-only
NOTIFICATION-TYPE