GSM7324-SWITCHING-MIB

File: GSM7324-SWITCHING-MIB.mib (152899 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC GSM7324-REF-MIB
RFC1155-SMI RFC1213-MIB Q-BRIDGE-MIB
IANAifType-MIB IF-MIB

Imported symbols

Unsigned32 Gauge32 Counter32
MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
IpAddress Integer32 RowStatus
MacAddress gsm7324 AgentPortMask
TimeTicks DisplayString PhysAddress
VlanIndex dot1qVlanIndex dot1qFdbId
IANAifType ifIndex

Defined Types

AgentTrapLogEntry  
SEQUENCE    
  agentTrapLogIndex Integer32
  agentTrapLogSystemTime DisplayString
  agentTrapLogTrap DisplayString

AgentSupportedMibEntry  
SEQUENCE    
  agentSupportedMibIndex Integer32
  agentSupportedMibName DisplayString
  agentSupportedMibDescription DisplayString

AgentLoginSessionEntry  
SEQUENCE    
  agentLoginSessionIndex Integer32
  agentLoginSessionUserName DisplayString
  agentLoginSessionIPAddress IpAddress
  agentLoginSessionConnectionType INTEGER
  agentLoginSessionIdleTime TimeTicks
  agentLoginSessionSessionTime TimeTicks
  agentLoginSessionStatus RowStatus

AgentUserConfigEntry  
SEQUENCE    
  agentUserIndex Integer32
  agentUserName DisplayString
  agentUserPassword DisplayString
  agentUserAccessMode INTEGER
  agentUserStatus RowStatus
  agentUserAuthenticationType INTEGER
  agentUserEncryptionType INTEGER
  agentUserEncryptionPassword DisplayString

AgentLagSummaryConfigEntry  
SEQUENCE    
  agentLagSummaryLagIndex Integer32
  agentLagSummaryName DisplayString
  agentLagSummaryFlushTimer Integer32
  agentLagSummaryLinkTrap INTEGER
  agentLagSummaryAdminMode INTEGER
  agentLagSummaryStpMode INTEGER
  agentLagSummaryAddPort Integer32
  agentLagSummaryDeletePort Integer32
  agentLagSummaryStatus RowStatus
  agentLagSummaryType INTEGER

AgentLagDetailedConfigEntry  
SEQUENCE    
  agentLagDetailedLagIndex Integer32
  agentLagDetailedIfIndex Integer32
  agentLagDetailedPortSpeed OBJECT IDENTIFIER
  agentLagDetailedPortStatus INTEGER

AgentSnmpCommunityConfigEntry  
SEQUENCE    
  agentSnmpCommunityIndex Integer32
  agentSnmpCommunityName DisplayString Size(1..16)
  agentSnmpCommunityIPAddress IpAddress
  agentSnmpCommunityIPMask IpAddress
  agentSnmpCommunityAccessMode INTEGER
  agentSnmpCommunityStatus INTEGER

AgentSnmpTrapReceiverConfigEntry  
SEQUENCE    
  agentSnmpTrapReceiverIndex Integer32
  agentSnmpTrapReceiverCommunityName DisplayString Size(1..16)
  agentSnmpTrapReceiverIPAddress IpAddress
  agentSnmpTrapReceiverStatus INTEGER

AgentSwitchAddressAgingTimeoutEntry  
SEQUENCE    
  agentSwitchAddressAgingTimeout Integer32

AgentSwitchMFDBEntry  
SEQUENCE    
  agentSwitchMFDBVlanId VlanIndex
  agentSwitchMFDBMacAddress MacAddress
  agentSwitchMFDBProtocolType INTEGER
  agentSwitchMFDBType INTEGER
  agentSwitchMFDBDescription DisplayString
  agentSwitchMFDBForwardingPortMask AgentPortMask
  agentSwitchMFDBFilteringPortMask AgentPortMask

AgentSwitchMFDBSummaryEntry  
SEQUENCE    
  agentSwitchMFDBSummaryVlanId VlanIndex
  agentSwitchMFDBSummaryMacAddress MacAddress
  agentSwitchMFDBSummaryForwardingPortMask AgentPortMask

AgentDot3adAggPortEntry  
SEQUENCE    
  agentDot3adAggPort Integer32
  agentDot3adAggPortLACPMode INTEGER

AgentPortConfigEntry  
SEQUENCE    
  agentPortDot1dBasePort Integer32
  agentPortIfIndex Integer32
  agentPortIanaType IANAifType
  agentPortSTPMode INTEGER
  agentPortSTPState INTEGER
  agentPortAdminMode INTEGER
  agentPortPhysicalMode INTEGER
  agentPortPhysicalStatus INTEGER
  agentPortLinkTrapMode INTEGER
  agentPortClearStats INTEGER
  agentPortDefaultType OBJECT IDENTIFIER
  agentPortType OBJECT IDENTIFIER
  agentPortAutoNegAdminStatus INTEGER
  agentPortDot3FlowControlMode INTEGER
  agentPortDVlanTagMode INTEGER
  agentPortDVlanTagEthertype Integer32
  agentPortDVlanTagCustomerId Integer32
  agentPortMaxFrameSizeLimit Integer32
  agentPortMaxFrameSize Integer32

AgentProtocolGroupEntry  
SEQUENCE    
  agentProtocolGroupId Integer32
  agentProtocolGroupName DisplayString
  agentProtocolGroupVlanId Integer32
  agentProtocolGroupProtocolIP INTEGER
  agentProtocolGroupProtocolARP INTEGER
  agentProtocolGroupProtocolIPX INTEGER
  agentProtocolGroupStatus RowStatus

AgentProtocolGroupPortEntry  
SEQUENCE    
  agentProtocolGroupId Integer32
  agentProtocolGroupPortIfIndex Integer32
  agentProtocolGroupPortStatus RowStatus

AgentStpPortEntry  
SEQUENCE    
  agentStpPortState INTEGER
  agentStpPortStatsMstpBpduRx Counter32
  agentStpPortStatsMstpBpduTx Counter32
  agentStpPortStatsRstpBpduRx Counter32
  agentStpPortStatsRstpBpduTx Counter32
  agentStpPortStatsStpBpduRx Counter32
  agentStpPortStatsStpBpduTx Counter32
  agentStpPortUpTime TimeTicks
  agentStpPortMigrationCheck INTEGER

AgentStpCstPortEntry  
SEQUENCE    
  agentStpCstPortOperEdge INTEGER
  agentStpCstPortOperPointToPoint INTEGER
  agentStpCstPortTopologyChangeAck INTEGER
  agentStpCstPortEdge INTEGER
  agentStpCstPortForwardingState INTEGER
  agentStpCstPortId STRING
  agentStpCstPortPathCost Unsigned32
  agentStpCstPortPriority Unsigned32
  agentStpCstDesignatedBridgeId STRING
  agentStpCstDesignatedCost Unsigned32
  agentStpCstDesignatedPortId STRING

AgentStpMstEntry  
SEQUENCE    
  agentStpMstId Unsigned32
  agentStpMstBridgePriority Unsigned32
  agentStpMstBridgeIdentifier STRING
  agentStpMstDesignatedRootId STRING
  agentStpMstRootPathCost Unsigned32
  agentStpMstRootPortId STRING
  agentStpMstTimeSinceTopologyChange TimeTicks
  agentStpMstTopologyChangeCount Counter32
  agentStpMstTopologyChangeParm INTEGER
  agentStpMstRowStatus RowStatus

AgentStpMstPortEntry  
SEQUENCE    
  agentStpMstPortForwardingState INTEGER
  agentStpMstPortId STRING
  agentStpMstPortPathCost Unsigned32
  agentStpMstPortPriority Unsigned32
  agentStpMstDesignatedBridgeId STRING
  agentStpMstDesignatedCost Unsigned32
  agentStpMstDesignatedPortId STRING

AgentStpMstVlanEntry  
SEQUENCE    
  agentStpMstVlanRowStatus RowStatus

AgentAuthenticationListEntry  
SEQUENCE    
  agentAuthenticationListIndex Unsigned32
  agentAuthenticationListName DisplayString
  agentAuthenticationListMethod1 INTEGER
  agentAuthenticationListMethod2 INTEGER
  agentAuthenticationListMethod3 INTEGER
  agentAuthenticationListStatus RowStatus

AgentUserAuthenticationConfigEntry  
SEQUENCE    
  agentUserAuthenticationList DisplayString

AgentUserPortConfigEntry  
SEQUENCE    
  agentUserPortSecurity AgentPortMask

AgentClassOfServiceEntry  
SEQUENCE    
  agentClassOfServicePriority Integer32
  agentClassOfServiceClass Integer32

Defined Values

gsm7324Switching 1.3.6.1.4.1.4526.1.7.1
Tok_String
MODULE-IDENTITY    

agentInfoGroup 1.3.6.1.4.1.4526.1.7.1.1
OBJECT IDENTIFIER    

agentInventoryGroup 1.3.6.1.4.1.4526.1.7.1.1.1
OBJECT IDENTIFIER    

agentInventorySysDescription 1.3.6.1.4.1.4526.1.7.1.1.1.1
The switch's Inventory system description.
OBJECT-TYPE    
  DisplayString  

agentInventoryMachineType 1.3.6.1.4.1.4526.1.7.1.1.1.2
Type of the Machine used in the Switch
OBJECT-TYPE    
  DisplayString  

agentInventoryBurnedInMacAddress 1.3.6.1.4.1.4526.1.7.1.1.1.3
Burned-In MAC Address
OBJECT-TYPE    
  PhysAddress  

agentInventoryAdditionalPackages 1.3.6.1.4.1.4526.1.7.1.1.1.4
Lists additional functional packages available on this unit.
OBJECT-TYPE    
  DisplayString  

agentInventorySoftwareVersion 1.3.6.1.4.1.4526.1.7.1.1.1.5
Lists the version of software loaded on this unit.
OBJECT-TYPE    
  DisplayString  

agentTrapLogGroup 1.3.6.1.4.1.4526.1.7.1.1.2
OBJECT IDENTIFIER    

agentTrapLogTotal 1.3.6.1.4.1.4526.1.7.1.1.2.1
The total number of traps sent since last reset.
OBJECT-TYPE    
  Integer32  

agentTrapLogTotalSinceLastViewed 1.3.6.1.4.1.4526.1.7.1.1.2.3
The number of traps sent since last viewed.
OBJECT-TYPE    
  Integer32  

agentTrapLogTable 1.3.6.1.4.1.4526.1.7.1.1.2.4
Agent Trap Log
OBJECT-TYPE    
  SEQUENCE OF  
    AgentTrapLogEntry

agentTrapLogEntry 1.3.6.1.4.1.4526.1.7.1.1.2.4.1
Agent trap log entry
OBJECT-TYPE    
  AgentTrapLogEntry  

agentTrapLogIndex 1.3.6.1.4.1.4526.1.7.1.1.2.4.1.1
Unique index of trap entry
OBJECT-TYPE    
  Integer32  

agentTrapLogSystemTime 1.3.6.1.4.1.4526.1.7.1.1.2.4.1.2
System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.
OBJECT-TYPE    
  DisplayString  

agentTrapLogTrap 1.3.6.1.4.1.4526.1.7.1.1.2.4.1.3
Description of the trap sent.
OBJECT-TYPE    
  STRING Size(0..512)  

agentSupportedMibTable 1.3.6.1.4.1.4526.1.7.1.1.3
Supported MIB table
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSupportedMibEntry

agentSupportedMibEntry 1.3.6.1.4.1.4526.1.7.1.1.3.1
Supported MIB entry
OBJECT-TYPE    
  AgentSupportedMibEntry  

agentSupportedMibIndex 1.3.6.1.4.1.4526.1.7.1.1.3.1.1
Unique index of the Supported MIB entry
OBJECT-TYPE    
  Integer32  

agentSupportedMibName 1.3.6.1.4.1.4526.1.7.1.1.3.1.2
The name of the MIB (RFC or IEEE) that is supported.
OBJECT-TYPE    
  DisplayString  

agentSupportedMibDescription 1.3.6.1.4.1.4526.1.7.1.1.3.1.3
Description of the MIB (RFC or IEEE) that is supported.
OBJECT-TYPE    
  STRING Size(0..512)  

agentConfigGroup 1.3.6.1.4.1.4526.1.7.1.2
OBJECT IDENTIFIER    

agentCLIConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.1
OBJECT IDENTIFIER    

agentLoginSessionTable 1.3.6.1.4.1.4526.1.7.1.2.1.1
A table of the switch's login session
OBJECT-TYPE    
  SEQUENCE OF  
    AgentLoginSessionEntry

agentLoginSessionEntry 1.3.6.1.4.1.4526.1.7.1.2.1.1.1
Login Session Entry
OBJECT-TYPE    
  AgentLoginSessionEntry  

agentLoginSessionIndex 1.3.6.1.4.1.4526.1.7.1.2.1.1.1.1
Agent Login Session Index of the switch
OBJECT-TYPE    
  Integer32  

agentLoginSessionUserName 1.3.6.1.4.1.4526.1.7.1.2.1.1.1.2
Agent Login Session UserName of the switch
OBJECT-TYPE    
  DisplayString  

agentLoginSessionIPAddress 1.3.6.1.4.1.4526.1.7.1.2.1.1.1.3
Agent Login Session IP Address of the switch
OBJECT-TYPE    
  IpAddress  

agentLoginSessionConnectionType 1.3.6.1.4.1.4526.1.7.1.2.1.1.1.4
Agent Login Session Connection Type of the switch
OBJECT-TYPE    
  INTEGER serial(1), telnet(2)  

agentLoginSessionIdleTime 1.3.6.1.4.1.4526.1.7.1.2.1.1.1.5
Agent Login Session Idle Time of the switch
OBJECT-TYPE    
  TimeTicks  

agentLoginSessionSessionTime 1.3.6.1.4.1.4526.1.7.1.2.1.1.1.6
Agent Login Session Time of the switch
OBJECT-TYPE    
  TimeTicks  

agentLoginSessionStatus 1.3.6.1.4.1.4526.1.7.1.2.1.1.1.7
Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.
OBJECT-TYPE    
  RowStatus  

agentTelnetConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.1.2
OBJECT IDENTIFIER    

agentTelnetLoginTimeout 1.3.6.1.4.1.4526.1.7.1.2.1.2.1
Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 0 to 160. A value of 0 indicates that a Telnet session remains active indefinitely. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.
OBJECT-TYPE    
  Integer32 0..160  

agentTelnetMaxSessions 1.3.6.1.4.1.4526.1.7.1.2.1.2.2
Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.
OBJECT-TYPE    
  Integer32 0..5  

agentTelnetAllowNewMode 1.3.6.1.4.1.4526.1.7.1.2.1.2.3
Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentUserConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.1.3
OBJECT IDENTIFIER    

agentUserConfigCreate 1.3.6.1.4.1.4526.1.7.1.2.1.3.1
Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).
OBJECT-TYPE    
  DisplayString Size(1..8)  

agentUserConfigTable 1.3.6.1.4.1.4526.1.7.1.2.1.3.2
User Config Table
OBJECT-TYPE    
  SEQUENCE OF  
    AgentUserConfigEntry

agentUserConfigEntry 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1
User Config Entry
OBJECT-TYPE    
  AgentUserConfigEntry  

agentUserIndex 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1.1
Agent User Config Index
OBJECT-TYPE    
  Integer32  

agentUserName 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1.2
Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters).
OBJECT-TYPE    
  DisplayString Size(1..8)  

agentUserPassword 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1.3
Agent User Password This object will return an empty string even if a password is set.
OBJECT-TYPE    
  DisplayString Size(0..8)  

agentUserAccessMode 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1.4
Agent User Access Mode
OBJECT-TYPE    
  INTEGER read(1), write(2)  

agentUserStatus 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1.5
Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.
OBJECT-TYPE    
  RowStatus  

agentUserAuthenticationType 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1.6
SNMPv3 User Authentication. The user passsword must be set to a string greater than or equal to 8 characters for this to be set to anything but none(1). none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication
OBJECT-TYPE    
  INTEGER none(1), hmacmd5(2), hmacsha(3)  

agentUserEncryptionType 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1.7
SNMPv3 User Encryption Can not be set to des(2) if agentUserAuthenticationType is set to none(1). none(1) - no encryption used des(2) - DES encryption used
OBJECT-TYPE    
  INTEGER none(1), des(2)  

agentUserEncryptionPassword 1.3.6.1.4.1.4526.1.7.1.2.1.3.2.1.8
SNMPv3 User Encryption Password This object will return an empty string even if a password is set. agentUserEncryptionType must be set to des(2) before this object can be configured. This object will return an empty string even if a password is set.
OBJECT-TYPE    
  DisplayString Size(8..64)  

agentSerialGroup 1.3.6.1.4.1.4526.1.7.1.2.1.5
OBJECT IDENTIFIER    

agentSerialTimeout 1.3.6.1.4.1.4526.1.7.1.2.1.5.1
agentSerialTimeout specifies the maximum connect time(in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely. The time range is 0 to 160.
OBJECT-TYPE    
  Integer32 0..160  

agentSerialBaudrate 1.3.6.1.4.1.4526.1.7.1.2.1.5.2
agentSerialBaudrate specifies the current baud rate at which the serial port will try to connect. The available values are 1200, 2400, 4800, 9600, 19200, 38400,57600, and 115200 baud.
OBJECT-TYPE    
  INTEGER baud-1200(1), baud-2400(2), baud-4800(3), baud-9600(4), baud-19200(5), baud-38400(6), baud-57600(7), baud-115200(8)  

agentSerialCharacterSize 1.3.6.1.4.1.4526.1.7.1.2.1.5.3
agentSerialCharacterSize specifies the number of bits in a character. The number of bits is always 8.
OBJECT-TYPE    
  Integer32  

agentSerialHWFlowControlMode 1.3.6.1.4.1.4526.1.7.1.2.1.5.4
agentSerialHardwareFlowControl specifies whether hardware flow-control is enabled or disabled. Hardware Flow Control is always disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSerialStopBits 1.3.6.1.4.1.4526.1.7.1.2.1.5.5
agentSerialStopBits specifies the number of Stop bits per character. The number of Stop bits is always 1.
OBJECT-TYPE    
  Integer32  

agentSerialParityType 1.3.6.1.4.1.4526.1.7.1.2.1.5.6
agentSerialParityType specifies the Parity Method used on the Serial Port. The Parity Method is always None.
OBJECT-TYPE    
  INTEGER even(1), odd(2), none(3)  

agentLagConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.2
OBJECT IDENTIFIER    

agentLagConfigCreate 1.3.6.1.4.1.4526.1.7.1.2.2.1
Agent LAG Create. When this object is set with a non-empty string, a new LAG will be created if possible with the entered string as its name.
OBJECT-TYPE    
  DisplayString Size(1..15)  

agentLagSummaryConfigTable 1.3.6.1.4.1.4526.1.7.1.2.2.2
A summary table of the switch's LAG config entries
OBJECT-TYPE    
  SEQUENCE OF  
    AgentLagSummaryConfigEntry

agentLagSummaryConfigEntry 1.3.6.1.4.1.4526.1.7.1.2.2.2.1
Switch's LAG config entry
OBJECT-TYPE    
  AgentLagSummaryConfigEntry  

agentLagSummaryLagIndex 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.1
Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable.
OBJECT-TYPE    
  Integer32  

agentLagSummaryName 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.2
Agent LAG Name. The associated name of the LAG used during creation.
OBJECT-TYPE    
  DisplayString Size(1..15)  

agentLagSummaryFlushTimer 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.3
Agent LAG FlushTimer.
OBJECT-TYPE    
  Integer32  

agentLagSummaryLinkTrap 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.4
Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentLagSummaryAdminMode 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.5
Agent LAG AdminMode. Administratively enables or disables this LAG interface.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentLagSummaryStpMode 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.6
Agent LAG StpMode If Dot1d is enabled, the valid values are: dot1d(1), fast(2), and off(3) If Dot1s is enabled, the valid values are: off(3) and dot1s(4)
OBJECT-TYPE    
  INTEGER dot1d(1), fast(2), off(3), dot1s(4)  

agentLagSummaryAddPort 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.7
Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.
OBJECT-TYPE    
  Integer32  

agentLagSummaryDeletePort 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.8
Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable.
OBJECT-TYPE    
  Integer32  

agentLagSummaryStatus 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.9
Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG.
OBJECT-TYPE    
  RowStatus  

agentLagSummaryType 1.3.6.1.4.1.4526.1.7.1.2.2.2.1.10
Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained.
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

agentLagDetailedConfigTable 1.3.6.1.4.1.4526.1.7.1.2.2.3
A detailed table of the switch's LAG config entries
OBJECT-TYPE    
  SEQUENCE OF  
    AgentLagDetailedConfigEntry

agentLagDetailedConfigEntry 1.3.6.1.4.1.4526.1.7.1.2.2.3.1
Switch's LAG config entry
OBJECT-TYPE    
  AgentLagDetailedConfigEntry  

agentLagDetailedLagIndex 1.3.6.1.4.1.4526.1.7.1.2.2.3.1.1
LAG index
OBJECT-TYPE    
  Integer32  

agentLagDetailedIfIndex 1.3.6.1.4.1.4526.1.7.1.2.2.3.1.2
LAG port index
OBJECT-TYPE    
  Integer32  

agentLagDetailedPortSpeed 1.3.6.1.4.1.4526.1.7.1.2.2.3.1.3
LAG port speed. See agentPortType for a description and list of valid values.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

agentLagDetailedPortStatus 1.3.6.1.4.1.4526.1.7.1.2.2.3.1.4
LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG.
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

agentLagConfigStaticCapability 1.3.6.1.4.1.4526.1.7.1.2.2.4
Agent LAG Static Capability. Configures whether Static LAGs are supported on this device.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentNetworkConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.3
OBJECT IDENTIFIER    

agentNetworkIPAddress 1.3.6.1.4.1.4526.1.7.1.2.3.1
The switch's network ip address
OBJECT-TYPE    
  IpAddress  

agentNetworkSubnetMask 1.3.6.1.4.1.4526.1.7.1.2.3.2
The switch's network subnet mask
OBJECT-TYPE    
  IpAddress  

agentNetworkDefaultGateway 1.3.6.1.4.1.4526.1.7.1.2.3.3
The switch's network default gateway
OBJECT-TYPE    
  IpAddress  

agentNetworkBurnedInMacAddress 1.3.6.1.4.1.4526.1.7.1.2.3.4
The switch's network Burned-In MAC address
OBJECT-TYPE    
  PhysAddress  

agentNetworkConfigProtocol 1.3.6.1.4.1.4526.1.7.1.2.3.5
The switch's network config protocol
OBJECT-TYPE    
  INTEGER none(1), bootp(2), dhcp(3)  

agentNetworkWebMode 1.3.6.1.4.1.4526.1.7.1.2.3.6
The switch's network config protocol on next bootup
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentNetworkJavaMode 1.3.6.1.4.1.4526.1.7.1.2.3.7
Configures the use of the Java interface through the Web.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentNetworkMgmtVlan 1.3.6.1.4.1.4526.1.7.1.2.3.8
The VLAN ID through which the switch can be managed using the agentNetworkIPAddress
OBJECT-TYPE    
  Integer32 1..4094  

agentServicePortConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.4
OBJECT IDENTIFIER    

agentServicePortIPAddress 1.3.6.1.4.1.4526.1.7.1.2.4.1
The switch's ServicePort ip address
OBJECT-TYPE    
  IpAddress  

agentServicePortSubnetMask 1.3.6.1.4.1.4526.1.7.1.2.4.2
The switch's ServicePort subnet mask
OBJECT-TYPE    
  IpAddress  

agentServicePortDefaultGateway 1.3.6.1.4.1.4526.1.7.1.2.4.3
The switch's ServicePort default gateway
OBJECT-TYPE    
  IpAddress  

agentServicePortBurnedInMacAddress 1.3.6.1.4.1.4526.1.7.1.2.4.4
The switch's ServicePort Burned-In MAC address
OBJECT-TYPE    
  PhysAddress  

agentServicePortConfigProtocol 1.3.6.1.4.1.4526.1.7.1.2.4.5
The switch's ServicePort config protocol
OBJECT-TYPE    
  INTEGER none(1), bootp(2), dhcp(3)  

agentSnmpConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.6
OBJECT IDENTIFIER    

agentSnmpCommunityCreate 1.3.6.1.4.1.4526.1.7.1.2.6.1
Creates a new SNMP Community entry. Defaults: IPAddress 0.0.0.0 IpMask 0.0.0.0 AccessMode read-only Status config
OBJECT-TYPE    
  DisplayString Size(1..16)  

agentSnmpCommunityConfigTable 1.3.6.1.4.1.4526.1.7.1.2.6.2
A table of the switch's SNMP Config entries
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSnmpCommunityConfigEntry

agentSnmpCommunityConfigEntry 1.3.6.1.4.1.4526.1.7.1.2.6.2.1
Switch's SNMP Config entry
OBJECT-TYPE    
  AgentSnmpCommunityConfigEntry  

agentSnmpCommunityIndex 1.3.6.1.4.1.4526.1.7.1.2.6.2.1.1
The switch's Snmp Community Index
OBJECT-TYPE    
  Integer32  

agentSnmpCommunityName 1.3.6.1.4.1.4526.1.7.1.2.6.2.1.2
The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored.
OBJECT-TYPE    
  DisplayString Size(1..16)  

agentSnmpCommunityIPAddress 1.3.6.1.4.1.4526.1.7.1.2.6.2.1.3
The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.
OBJECT-TYPE    
  IpAddress  

agentSnmpCommunityIPMask 1.3.6.1.4.1.4526.1.7.1.2.6.2.1.4
The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255.
OBJECT-TYPE    
  IpAddress  

agentSnmpCommunityAccessMode 1.3.6.1.4.1.4526.1.7.1.2.6.2.1.5
The switch's Snmp Community Access Mode Access Mode - This value can be read-only or read/write. A community with a read-only access allows for switch information to be displayed. A community with a read/write access allows for configuration changes to be made and for information to be displayed.
OBJECT-TYPE    
  INTEGER read-only(1), read-write(2)  

agentSnmpCommunityStatus 1.3.6.1.4.1.4526.1.7.1.2.6.2.1.6
The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP managers associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent.
OBJECT-TYPE    
  INTEGER active(1), notInService(2), config(3), destroy(4)  

agentSnmpTrapReceiverCreate 1.3.6.1.4.1.4526.1.7.1.2.6.3
Creates a new trap receiver entry. Defaults: IPAddress 0.0.0.0 status config
OBJECT-TYPE    
  DisplayString Size(1..16)  

agentSnmpTrapReceiverConfigTable 1.3.6.1.4.1.4526.1.7.1.2.6.4
Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSnmpTrapReceiverConfigEntry

agentSnmpTrapReceiverConfigEntry 1.3.6.1.4.1.4526.1.7.1.2.6.4.1
Switch's Snmp Trace Receiver Config entry
OBJECT-TYPE    
  AgentSnmpTrapReceiverConfigEntry  

agentSnmpTrapReceiverIndex 1.3.6.1.4.1.4526.1.7.1.2.6.4.1.1
The switch's Snmp Trap Receiver Index
OBJECT-TYPE    
  Integer32  

agentSnmpTrapReceiverCommunityName 1.3.6.1.4.1.4526.1.7.1.2.6.4.1.2
The switch's Snmp Trap Receiver Community Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case-sensitive.
OBJECT-TYPE    
  DisplayString Size(1..16)  

agentSnmpTrapReceiverIPAddress 1.3.6.1.4.1.4526.1.7.1.2.6.4.1.3
IP Address - Each IP address parameter is four integer numbers. The numbers range from 0 to 255.
OBJECT-TYPE    
  IpAddress  

agentSnmpTrapReceiverStatus 1.3.6.1.4.1.4526.1.7.1.2.6.4.1.4
The switch's Snmp Trap Reciever Status. active(1) - This trap receiver is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap reciever is not active; no SNMP Traps will be sent to this reciever until it's set back to active(1). config(3) - The trap reciever Status must be set to this value in order to configure it. When creating a new trap receiver entry, the Status will initially be set to this value. Note: agentSnmpTrapReceiverIPAddress must be set to non-zero before changing to active(1) or notInService(2). destroy(4) - Set to this value to remove the trap receiver entry from the agent.
OBJECT-TYPE    
  INTEGER active(1), notInService(2), config(3), destroy(4)  

agentSnmpTrapFlagsConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.6.5
OBJECT IDENTIFIER    

agentSnmpAuthenticationTrapFlag 1.3.6.1.4.1.4526.1.7.1.2.6.5.1
Authentication Flag - Enable/Disable authentication Flag.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSnmpLinkUpDownTrapFlag 1.3.6.1.4.1.4526.1.7.1.2.6.5.2
Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSnmpMultipleUsersTrapFlag 1.3.6.1.4.1.4526.1.7.1.2.6.5.3
Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSnmpSpanningTreeTrapFlag 1.3.6.1.4.1.4526.1.7.1.2.6.5.4
Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSnmpBroadcastStormTrapFlag 1.3.6.1.4.1.4526.1.7.1.2.6.5.5
Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSpanningTreeConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.7
OBJECT IDENTIFIER    

agentSpanningTreeMode 1.3.6.1.4.1.4526.1.7.1.2.7.1
The switch's Spanning Tree Switch Status
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.8
OBJECT IDENTIFIER    

agentSwitchAddressAgingTimeoutTable 1.3.6.1.4.1.4526.1.7.1.2.8.4
The switch's address aging timeout table
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchAddressAgingTimeoutEntry

agentSwitchAddressAgingTimeoutEntry 1.3.6.1.4.1.4526.1.7.1.2.8.4.1
Aging information about a specific Filtering Database.
OBJECT-TYPE    
  AgentSwitchAddressAgingTimeoutEntry  

agentSwitchAddressAgingTimeout 1.3.6.1.4.1.4526.1.7.1.2.8.4.1.1
The FDB entry's address aging timeout (in seconds)
OBJECT-TYPE    
  Integer32 10..1000000  

agentSwitchBroadcastControlMode 1.3.6.1.4.1.4526.1.7.1.2.8.2
The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds 20 percent of the link speed, the switch blocks (discards) the broadcast traffic until the broadcast traffic returns to 10 percent or less. Upper limit for 10M link is 20% and lower limit is 10%. For 100M link Upper limit is 5% and lower limit is 2%
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchDot3FlowControlMode 1.3.6.1.4.1.4526.1.7.1.2.8.3
Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIGMPSnoopingGroup 1.3.6.1.4.1.4526.1.7.1.2.8.6
OBJECT IDENTIFIER    

agentSwitchIGMPSnoopingAdminMode 1.3.6.1.4.1.4526.1.7.1.2.8.6.1
This enables or disables IGMP Snooping on the system.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIGMPSnoopingGroupMembershipInterval 1.3.6.1.4.1.4526.1.7.1.2.8.6.2
The amount of time in seconds a switch will wait for a report for a particular group on a particular interface before it deletes the interface from the entry.
OBJECT-TYPE    
  Integer32 1..3600  

agentSwitchIGMPSnoopingMaxResponseTime 1.3.6.1.4.1.4526.1.7.1.2.8.6.3
The amount of time in seconds a switch will wait after sending a query on an interface because it did not receive a report for a particular group in that interface. This value must be less than agentSwitchIGMPSnoopingQueryInterval.
OBJECT-TYPE    
  Integer32 1..3600  

agentSwitchIGMPSnoopingMRPExpirationTime 1.3.6.1.4.1.4526.1.7.1.2.8.6.4
Multicast Router Present Expiration Time. The amount of time in seconds a switch will wait for a query to be received on an interface before the interface is removed from the list of interfaces with mutlticast routers attached. A value of zero indicates an infinite timeout, i.e. the entries in the list will not expire.
OBJECT-TYPE    
  Integer32 0..3600  

agentSwitchIGMPSnoopingPortMask 1.3.6.1.4.1.4526.1.7.1.2.8.6.5
IGMP Snooping Port Mask. This allows configuration of IGMP Snooping on selected ports. IGMP Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a port which has IGMP Snooping enabled becomes enabled for routing, or is enlisted as a member of a LAG, IGMP Snooping functionality will be disabled on that port. IGMP Snooping functionality will be subsequently be reenabled if routing is disabled or LAG membership is removed from an interface that had previously had IGMP Snooping enabled. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
OBJECT-TYPE    
  AgentPortMask  

agentSwitchIGMPSnoopingMulticastControlFramesProcessed 1.3.6.1.4.1.4526.1.7.1.2.8.6.6
Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU.
OBJECT-TYPE    
  Counter32  

agentSwitchMFDBGroup 1.3.6.1.4.1.4526.1.7.1.2.8.7
OBJECT IDENTIFIER    

agentSwitchMFDBTable 1.3.6.1.4.1.4526.1.7.1.2.8.7.1
The Multicast Forwarding Database table
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchMFDBEntry

agentSwitchMFDBEntry 1.3.6.1.4.1.4526.1.7.1.2.8.7.1.1
Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User.
OBJECT-TYPE    
  AgentSwitchMFDBEntry  

agentSwitchMFDBVlanId 1.3.6.1.4.1.4526.1.7.1.2.8.7.1.1.1
Vlan Index for which this entry is associated with.
OBJECT-TYPE    
  VlanIndex  

agentSwitchMFDBMacAddress 1.3.6.1.4.1.4526.1.7.1.2.8.7.1.1.2
A multicast MAC address for which the switch has forwarding and or filtering information.
OBJECT-TYPE    
  MacAddress  

agentSwitchMFDBProtocolType 1.3.6.1.4.1.4526.1.7.1.2.8.7.1.1.3
The component that is responsible for this entry in the Multicast Forwarding Database.
OBJECT-TYPE    
  INTEGER static(1), gmrp(2), igmp(3)  

agentSwitchMFDBType 1.3.6.1.4.1.4526.1.7.1.2.8.7.1.1.4
This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

agentSwitchMFDBDescription 1.3.6.1.4.1.4526.1.7.1.2.8.7.1.1.5
Text description of this multicast table entry.
OBJECT-TYPE    
  DisplayString  

agentSwitchMFDBForwardingPortMask 1.3.6.1.4.1.4526.1.7.1.2.8.7.1.1.6
BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
OBJECT-TYPE    
  AgentPortMask  

agentSwitchMFDBFilteringPortMask 1.3.6.1.4.1.4526.1.7.1.2.8.7.1.1.7
BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
OBJECT-TYPE    
  AgentPortMask  

agentSwitchMFDBSummaryTable 1.3.6.1.4.1.4526.1.7.1.2.8.7.2
The Multicast Forwarding Database Summary table
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchMFDBSummaryEntry

agentSwitchMFDBSummaryEntry 1.3.6.1.4.1.4526.1.7.1.2.8.7.2.1
Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address.
OBJECT-TYPE    
  AgentSwitchMFDBSummaryEntry  

agentSwitchMFDBSummaryVlanId 1.3.6.1.4.1.4526.1.7.1.2.8.7.2.1.1
Vlan Index for which this entry is associated with.
OBJECT-TYPE    
  VlanIndex  

agentSwitchMFDBSummaryMacAddress 1.3.6.1.4.1.4526.1.7.1.2.8.7.2.1.2
A multicast MAC address for which the switch has forwarding and or filtering information.
OBJECT-TYPE    
  MacAddress  

agentSwitchMFDBSummaryForwardingPortMask 1.3.6.1.4.1.4526.1.7.1.2.8.7.2.1.3
Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
OBJECT-TYPE    
  AgentPortMask  

agentSwitchMFDBMaxTableEntries 1.3.6.1.4.1.4526.1.7.1.2.8.7.3
This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table.
OBJECT-TYPE    
  Gauge32  

agentSwitchMFDBMostEntriesUsed 1.3.6.1.4.1.4526.1.7.1.2.8.7.4
This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark.
OBJECT-TYPE    
  Gauge32  

agentSwitchMFDBCurrentEntries 1.3.6.1.4.1.4526.1.7.1.2.8.7.5
This displays the current number of entries in the Multicast Forwarding Database table.
OBJECT-TYPE    
  Gauge32  

agentTransferConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.9
OBJECT IDENTIFIER    

agentTransferUploadGroup 1.3.6.1.4.1.4526.1.7.1.2.9.1
OBJECT IDENTIFIER    

agentTransferUploadMode 1.3.6.1.4.1.4526.1.7.1.2.9.1.1
Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
OBJECT-TYPE    
  INTEGER tftp(1), xmodem(2), ymodem(3), zmodem(4)  

agentTransferUploadServerIP 1.3.6.1.4.1.4526.1.7.1.2.9.1.2
Transfer upload tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
OBJECT-TYPE    
  IpAddress  

agentTransferUploadPath 1.3.6.1.4.1.4526.1.7.1.2.9.1.3
Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.
OBJECT-TYPE    
  DisplayString Size(0..31)  

agentTransferUploadFilename 1.3.6.1.4.1.4526.1.7.1.2.9.1.4
Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c: ftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
OBJECT-TYPE    
  DisplayString Size(0..31)  

agentTransferUploadDataType 1.3.6.1.4.1.4526.1.7.1.2.9.1.5
Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - Message log - Trap log
OBJECT-TYPE    
  INTEGER config(2), errorlog(3), messagelog(4), traplog(5)  

agentTransferUploadStart 1.3.6.1.4.1.4526.1.7.1.2.9.1.6
Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentTransferUploadStatus 1.3.6.1.4.1.4526.1.7.1.2.9.1.7
Indicates the current status of an upload transfer.
OBJECT-TYPE    
  INTEGER notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13)  

agentTransferDownloadGroup 1.3.6.1.4.1.4526.1.7.1.2.9.2
OBJECT IDENTIFIER    

agentTransferDownloadMode 1.3.6.1.4.1.4526.1.7.1.2.9.2.1
Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
OBJECT-TYPE    
  INTEGER tftp(1), xmodem(2), ymodem(3), zmodem(4)  

agentTransferDownloadServerIP 1.3.6.1.4.1.4526.1.7.1.2.9.2.2
Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
OBJECT-TYPE    
  IpAddress  

agentTransferDownloadPath 1.3.6.1.4.1.4526.1.7.1.2.9.2.3
Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used.
OBJECT-TYPE    
  DisplayString Size(0..31)  

agentTransferDownloadFilename 1.3.6.1.4.1.4526.1.7.1.2.9.2.4
Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c: ftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
OBJECT-TYPE    
  DisplayString Size(0..31)  

agentTransferDownloadDataType 1.3.6.1.4.1.4526.1.7.1.2.9.2.5
Transfer download datatype configures the type of file to download to the switch. The types for download are: code - Code File config - Configuration File sshkey-rsa1 - SSH-1 RSA Key File sshkey-rsa2 - SSH-2 RSA Key PEM File sshkey-dsa - SSH-2 DSA Key PEM File sslpem-root - SSL Trusted Root Certificate PEM File sslpem-server - SSL Server Certificate PEM File sslpem-dhweak - SSL DH Weak Encryption Parameter PEM File sslpem-dhstrong - SSL DH Strong Encryption Parameter PEM File Note: SSH Key files can only be downloaded if SSH Server is administratively disabled, and there are no active SSH sessions.
OBJECT-TYPE    
  INTEGER code(2), config(3), sshkey-rsa1(4), sshkey-rsa2(5), sshkey-dsa(6), sslpem-root(7), sslpem-server(8), sslpem-dhweak(9), sslpem-dhstrong(10)  

agentTransferDownloadStart 1.3.6.1.4.1.4526.1.7.1.2.9.2.6
Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentTransferDownloadStatus 1.3.6.1.4.1.4526.1.7.1.2.9.2.7
Indicates the current status of an download transfer.
OBJECT-TYPE    
  INTEGER notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13)  

agentPortMirroringGroup 1.3.6.1.4.1.4526.1.7.1.2.10
OBJECT IDENTIFIER    

agentMirroredPortIfIndex 1.3.6.1.4.1.4526.1.7.1.2.10.1
IfIndex of the mirrored port
OBJECT-TYPE    
  Integer32  

agentProbePortIfIndex 1.3.6.1.4.1.4526.1.7.1.2.10.2
IfIndex of the probe port
OBJECT-TYPE    
  Integer32  

agentPortMirroringMode 1.3.6.1.4.1.4526.1.7.1.2.10.3
Port mirroring mode: enable - enable mirroring mode disable - disable mirroring mode delete - clear MirroredPort and Probe Port configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2), delete(3)  

agentDot3adAggPortTable 1.3.6.1.4.1.4526.1.7.1.2.12
This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentDot3adAggPortEntry

agentDot3adAggPortEntry 1.3.6.1.4.1.4526.1.7.1.2.12.1
Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port.
OBJECT-TYPE    
  AgentDot3adAggPortEntry  

agentDot3adAggPort 1.3.6.1.4.1.4526.1.7.1.2.12.1.1
ifIndex of this physical port
OBJECT-TYPE    
  Integer32  

agentDot3adAggPortLACPMode 1.3.6.1.4.1.4526.1.7.1.2.12.1.2
Enable/disable 802.3ad LACP on this port
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentPortConfigTable 1.3.6.1.4.1.4526.1.7.1.2.13
A table of the switch's physical port config entries
OBJECT-TYPE    
  SEQUENCE OF  
    AgentPortConfigEntry

agentPortConfigEntry 1.3.6.1.4.1.4526.1.7.1.2.13.1
Switch's physical port config entry
OBJECT-TYPE    
  AgentPortConfigEntry  

agentPortDot1dBasePort 1.3.6.1.4.1.4526.1.7.1.2.13.1.1
The port number of this port.
OBJECT-TYPE    
  Integer32 1..65535  

agentPortIfIndex 1.3.6.1.4.1.4526.1.7.1.2.13.1.2
The switch's Port IfIndex
OBJECT-TYPE    
  Integer32  

agentPortIanaType 1.3.6.1.4.1.4526.1.7.1.2.13.1.3
The switch's Port Type
OBJECT-TYPE    
  IANAifType  

agentPortSTPMode 1.3.6.1.4.1.4526.1.7.1.2.13.1.4
The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port This object is only supported when the Dot1d Protocol is enabled.
OBJECT-TYPE    
  INTEGER dot1d(1), fast(2), off(3)  

agentPortSTPState 1.3.6.1.4.1.4526.1.7.1.2.13.1.5
The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled.
OBJECT-TYPE    
  INTEGER blocking(1), listening(2), learning(3), forwarding(4), disabled(5)  

agentPortAdminMode 1.3.6.1.4.1.4526.1.7.1.2.13.1.6
The switch's Port Admin Mode
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentPortPhysicalMode 1.3.6.1.4.1.4526.1.7.1.2.13.1.7
The switch's Port Speed Mode. This is the configured physical mode. This object is read-only for gigabit ports
OBJECT-TYPE    
  INTEGER auto-negotiate(1), half-10(2), full-10(3), half-100(4), full-100(5), half-100fx(6), full-100fx(7), full-1000sx(8)  

agentPortPhysicalStatus 1.3.6.1.4.1.4526.1.7.1.2.13.1.8
The switch's Port Physical Speed Status. This is the current actual speed.
OBJECT-TYPE    
  INTEGER auto-negotiate(1), half-10(2), full-10(3), half-100(4), full-100(5), half-100fx(6), full-100fx(7), full-1000sx(8)  

agentPortLinkTrapMode 1.3.6.1.4.1.4526.1.7.1.2.13.1.9
If enabled, link up and link down traps will be sent for this port.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentPortClearStats 1.3.6.1.4.1.4526.1.7.1.2.13.1.10
clear stats for this port only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentPortDefaultType 1.3.6.1.4.1.4526.1.7.1.2.13.1.11
This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD
OBJECT-TYPE    
  OBJECT IDENTIFIER  

agentPortType 1.3.6.1.4.1.4526.1.7.1.2.13.1.12
This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object agentPortDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object agentPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType1000BaseTFD
OBJECT-TYPE    
  OBJECT IDENTIFIER  

agentPortAutoNegAdminStatus 1.3.6.1.4.1.4526.1.7.1.2.13.1.13
This object identifies the administration status of auto negotiation for this port.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentPortDot3FlowControlMode 1.3.6.1.4.1.4526.1.7.1.2.13.1.14
Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentPortDVlanTagMode 1.3.6.1.4.1.4526.1.7.1.2.13.1.15
Controls the Double Vlan Tag mode on this port.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentPortDVlanTagEthertype 1.3.6.1.4.1.4526.1.7.1.2.13.1.16
Configures the Ethertype for the Double Vlan Tag for this port. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).
OBJECT-TYPE    
  Integer32 0..65535  

agentPortDVlanTagCustomerId 1.3.6.1.4.1.4526.1.7.1.2.13.1.17
Configures the Customer ID for the Double Vlan Tag for this port.
OBJECT-TYPE    
  Integer32  

agentPortMaxFrameSizeLimit 1.3.6.1.4.1.4526.1.7.1.2.13.1.18
This object identifies the largest value that can be configured for agentPortMaxFrameSize
OBJECT-TYPE    
  Integer32  

agentPortMaxFrameSize 1.3.6.1.4.1.4526.1.7.1.2.13.1.19
This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of agentPortMaxFrameSizeLimit. For Ethernet ports which support 802.1Q vlan tagging, the minimum value that this object can be set to is 1522
OBJECT-TYPE    
  Integer32  

agentProtocolConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.14
OBJECT IDENTIFIER    

agentProtocolGroupCreate 1.3.6.1.4.1.4526.1.7.1.2.14.1
Set to non-empty string to create a Protocol-Based VLAN group.
OBJECT-TYPE    
  DisplayString Size(1..16)  

agentProtocolGroupTable 1.3.6.1.4.1.4526.1.7.1.2.14.2
A table of the switch's Protocol-based VLAN entries
OBJECT-TYPE    
  SEQUENCE OF  
    AgentProtocolGroupEntry

agentProtocolGroupEntry 1.3.6.1.4.1.4526.1.7.1.2.14.2.1
Switch's Protocol-based VLAN entry
OBJECT-TYPE    
  AgentProtocolGroupEntry  

agentProtocolGroupId 1.3.6.1.4.1.4526.1.7.1.2.14.2.1.1
Group identifier of the Protocol-based VLAN entry.
OBJECT-TYPE    
  Integer32  

agentProtocolGroupName 1.3.6.1.4.1.4526.1.7.1.2.14.2.1.2
Group name of the Protocol-based VLAN entry.
OBJECT-TYPE    
  DisplayString  

agentProtocolGroupVlanId 1.3.6.1.4.1.4526.1.7.1.2.14.2.1.3
VLAN associated with the Protocol-based VLAN entry. Set to 0 to remove.
OBJECT-TYPE    
  Integer32  

agentProtocolGroupProtocolIP 1.3.6.1.4.1.4526.1.7.1.2.14.2.1.4
The status of the IP protocol association with the Protocol-based VLAN entry.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentProtocolGroupProtocolARP 1.3.6.1.4.1.4526.1.7.1.2.14.2.1.5
The status of the ARP protocol association with the Protocol-based VLAN entry.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentProtocolGroupProtocolIPX 1.3.6.1.4.1.4526.1.7.1.2.14.2.1.6
The status of the IPX protocol association with the Protocol-based VLAN entry.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentProtocolGroupStatus 1.3.6.1.4.1.4526.1.7.1.2.14.2.1.7
The status of the Protocol-based VLAN entry. active(1) - this entry is active destroy(6) - remove this entry
OBJECT-TYPE    
  RowStatus  

agentProtocolGroupPortTable 1.3.6.1.4.1.4526.1.7.1.2.14.3
A table of the switch's physical port config entries
OBJECT-TYPE    
  SEQUENCE OF  
    AgentProtocolGroupPortEntry

agentProtocolGroupPortEntry 1.3.6.1.4.1.4526.1.7.1.2.14.3.1
Switch's physical port config entry
OBJECT-TYPE    
  AgentProtocolGroupPortEntry  

agentProtocolGroupPortIfIndex 1.3.6.1.4.1.4526.1.7.1.2.14.3.1.1
The interface number of this instance.
OBJECT-TYPE    
  Integer32  

agentProtocolGroupPortStatus 1.3.6.1.4.1.4526.1.7.1.2.14.3.1.2
The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group
OBJECT-TYPE    
  RowStatus  

agentStpSwitchConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.15
OBJECT IDENTIFIER    

agentStpConfigDigestKey 1.3.6.1.4.1.4526.1.7.1.2.15.1
The MST configuration digest key.
OBJECT-TYPE    
  STRING Size(16)  

agentStpConfigFormatSelector 1.3.6.1.4.1.4526.1.7.1.2.15.2
The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard.
OBJECT-TYPE    
  Unsigned32 0..255  

agentStpConfigName 1.3.6.1.4.1.4526.1.7.1.2.15.3
The MST configuration name of at most 32 characters.
OBJECT-TYPE    
  DisplayString Size(1..32)  

agentStpConfigRevision 1.3.6.1.4.1.4526.1.7.1.2.15.4
The MST configuration revision. The default value is 1.
OBJECT-TYPE    
  Unsigned32 0..65535  

agentStpForceVersion 1.3.6.1.4.1.4526.1.7.1.2.15.5
The MST configuration force protocol version. The default version is dot1s.
OBJECT-TYPE    
  INTEGER dot1d(1), dot1w(2), dot1s(3)  

agentStpAdminMode 1.3.6.1.4.1.4526.1.7.1.2.15.6
The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational status on the switch. The default status is disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentStpPortTable 1.3.6.1.4.1.4526.1.7.1.2.15.7
STP port table.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentStpPortEntry

agentStpPortEntry 1.3.6.1.4.1.4526.1.7.1.2.15.7.1
STP port entry.
OBJECT-TYPE    
  AgentStpPortEntry  

agentStpPortState 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.1
The administrative bridge port state. enable(1) - enables the port. disable(2) - disables the port. The default port state is enabled for the first 4095 ports and disabled for any ports beyond.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentStpPortStatsMstpBpduRx 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.2
The MSTP BPDUs received on a specific port.
OBJECT-TYPE    
  Counter32  

agentStpPortStatsMstpBpduTx 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.3
The MSTP BPDUs sent from a specific port.
OBJECT-TYPE    
  Counter32  

agentStpPortStatsRstpBpduRx 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.4
The RSTP BPDUs received on a specific port.
OBJECT-TYPE    
  Counter32  

agentStpPortStatsRstpBpduTx 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.5
The RSTP BPDUs sent from a specific port.
OBJECT-TYPE    
  Counter32  

agentStpPortStatsStpBpduRx 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.6
The STP BPDUs received on a specific port.
OBJECT-TYPE    
  Counter32  

agentStpPortStatsStpBpduTx 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.7
The STP BPDUs sent from a specific port.
OBJECT-TYPE    
  Counter32  

agentStpPortUpTime 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.8
Time since port was reset. It is displayed in days, hours, minutes, and seconds.
OBJECT-TYPE    
  TimeTicks  

agentStpPortMigrationCheck 1.3.6.1.4.1.4526.1.7.1.2.15.7.1.9
Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A non-zero value indicates that BPDUs are to be sent on the specified port.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

agentStpCstConfigGroup 1.3.6.1.4.1.4526.1.7.1.2.15.8
OBJECT IDENTIFIER    

agentStpCstHelloTime 1.3.6.1.4.1.4526.1.7.1.2.15.8.1
The MSTP root port hello time for the CIST.
OBJECT-TYPE    
  Unsigned32  

agentStpCstMaxAge 1.3.6.1.4.1.4526.1.7.1.2.15.8.2
The MSTP root port max age for the CIST.
OBJECT-TYPE    
  Unsigned32  

agentStpCstRegionalRootId 1.3.6.1.4.1.4526.1.7.1.2.15.8.3
The MSTP regional root identifier for the CIST.
OBJECT-TYPE    
  STRING Size(8)  

agentStpCstRegionalRootPathCost 1.3.6.1.4.1.4526.1.7.1.2.15.8.4
The MSTP regional root path cost for the CIST.
OBJECT-TYPE    
  Unsigned32  

agentStpCstRootFwdDelay 1.3.6.1.4.1.4526.1.7.1.2.15.8.5
The MSTP root port forward delay for the CIST.
OBJECT-TYPE    
  Unsigned32  

agentStpCstBridgeFwdDelay 1.3.6.1.4.1.4526.1.7.1.2.15.8.6
The MSTP bridge forward delay for the CIST. The default value is 15.
OBJECT-TYPE    
  Unsigned32 4..30  

agentStpCstBridgeHelloTime 1.3.6.1.4.1.4526.1.7.1.2.15.8.7
The MSTP bridge hello time for the CIST. The default value is 2.
OBJECT-TYPE    
  Unsigned32 1..10  

agentStpCstBridgeHoldTime 1.3.6.1.4.1.4526.1.7.1.2.15.8.8
The MSTP bridge hold time for the CIST.
OBJECT-TYPE    
  Unsigned32  

agentStpCstBridgeMaxAge 1.3.6.1.4.1.4526.1.7.1.2.15.8.9
The MSTP bridge max age for the CIST. The default value is 20.
OBJECT-TYPE    
  Unsigned32 6..40  

agentStpCstPortTable 1.3.6.1.4.1.4526.1.7.1.2.15.9
CIST port table.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentStpCstPortEntry

agentStpCstPortEntry 1.3.6.1.4.1.4526.1.7.1.2.15.9.1
CIST port entry.
OBJECT-TYPE    
  AgentStpCstPortEntry  

agentStpCstPortOperEdge 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.1
The MSTP operational status of a specific port for the CIST.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentStpCstPortOperPointToPoint 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.2
The MSTP operational point to point mac of a specific port for the CIST.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

agentStpCstPortTopologyChangeAck 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.3
The MSTP topology change acknowledge for a specific port in the CIST.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

agentStpCstPortEdge 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.4
The administrative state of a specific port in CIST. enable(1) - enables the port. disable(2) - disables the port. The default port state is disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentStpCstPortForwardingState 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.5
The MSTP forwarding state of a specific port in CIST.
OBJECT-TYPE    
  INTEGER discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6)  

agentStpCstPortId 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.6
The MSTP port identifier of a specific port in CIST.
OBJECT-TYPE    
  STRING Size(4)  

agentStpCstPortPathCost 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.7
The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
OBJECT-TYPE    
  Unsigned32 0..200000000  

agentStpCstPortPriority 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.8
The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128.
OBJECT-TYPE    
  Unsigned32 0..240  

agentStpCstDesignatedBridgeId 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.9
The MSTP designated bridge ID of a specific port in CIST.
OBJECT-TYPE    
  STRING Size(8)  

agentStpCstDesignatedCost 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.10
The MSTP designated cost of a specific port in CIST.
OBJECT-TYPE    
  Unsigned32  

agentStpCstDesignatedPortId 1.3.6.1.4.1.4526.1.7.1.2.15.9.1.11
The MSTP designated port ID of a specific port in CIST.
OBJECT-TYPE    
  STRING Size(2)  

agentStpMstTable 1.3.6.1.4.1.4526.1.7.1.2.15.10
MST table.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentStpMstEntry

agentStpMstEntry 1.3.6.1.4.1.4526.1.7.1.2.15.10.1
MST entry.
OBJECT-TYPE    
  AgentStpMstEntry  

agentStpMstId 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.1
The MSTP instance ID.
OBJECT-TYPE    
  Unsigned32  

agentStpMstBridgePriority 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.2
The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768.
OBJECT-TYPE    
  Unsigned32 0..61440  

agentStpMstBridgeIdentifier 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.3
The MSTP bridge identifier in a specific instance.
OBJECT-TYPE    
  STRING Size(8)  

agentStpMstDesignatedRootId 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.4
The MSTP designated root bridge identifier in a specific instance.
OBJECT-TYPE    
  STRING Size(8)  

agentStpMstRootPathCost 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.5
The MSTP root path cost in a specific instance.
OBJECT-TYPE    
  Unsigned32  

agentStpMstRootPortId 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.6
The MSTP root port ID in a specific instance.
OBJECT-TYPE    
  STRING Size(8)  

agentStpMstTimeSinceTopologyChange 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.7
The MSTP time since the last topology change in a specific instance.
OBJECT-TYPE    
  TimeTicks  

agentStpMstTopologyChangeCount 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.8
The MSTP count of topology changes in a specific instance.
OBJECT-TYPE    
  Counter32  

agentStpMstTopologyChangeParm 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.9
The MSTP topology change parameter in a specific instance.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

agentStpMstRowStatus 1.3.6.1.4.1.4526.1.7.1.2.15.10.1.10
The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance.
OBJECT-TYPE    
  RowStatus  

agentStpMstPortTable 1.3.6.1.4.1.4526.1.7.1.2.15.11
MST port table.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentStpMstPortEntry

agentStpMstPortEntry 1.3.6.1.4.1.4526.1.7.1.2.15.11.1
MST port entry.
OBJECT-TYPE    
  AgentStpMstPortEntry  

agentStpMstPortForwardingState 1.3.6.1.4.1.4526.1.7.1.2.15.11.1.1
The MSTP forwarding state of a specific port in a specific instance.
OBJECT-TYPE    
  INTEGER discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6)  

agentStpMstPortId 1.3.6.1.4.1.4526.1.7.1.2.15.11.1.2
The MSTP port identifier of a specific port in a specific instance.
OBJECT-TYPE    
  STRING Size(4)  

agentStpMstPortPathCost 1.3.6.1.4.1.4526.1.7.1.2.15.11.1.3
The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
OBJECT-TYPE    
  Unsigned32 0..200000000  

agentStpMstPortPriority 1.3.6.1.4.1.4526.1.7.1.2.15.11.1.4
The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128.
OBJECT-TYPE    
  Unsigned32 0..240  

agentStpMstDesignatedBridgeId 1.3.6.1.4.1.4526.1.7.1.2.15.11.1.5
The MSTP designated bridge ID of a specific port in a specific instance.
OBJECT-TYPE    
  STRING Size(8)  

agentStpMstDesignatedCost 1.3.6.1.4.1.4526.1.7.1.2.15.11.1.6
The MSTP designated cost of a specific port in a specific instance.
OBJECT-TYPE    
  Unsigned32  

agentStpMstDesignatedPortId 1.3.6.1.4.1.4526.1.7.1.2.15.11.1.7
The MSTP designated port ID of a specific port in a specific instance.
OBJECT-TYPE    
  STRING Size(2)  

agentStpMstVlanTable 1.3.6.1.4.1.4526.1.7.1.2.15.12
MST VLAN table.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentStpMstVlanEntry

agentStpMstVlanEntry 1.3.6.1.4.1.4526.1.7.1.2.15.12.1
MST VLAN entry.
OBJECT-TYPE    
  AgentStpMstVlanEntry  

agentStpMstVlanRowStatus 1.3.6.1.4.1.4526.1.7.1.2.15.12.1.1
The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN.
OBJECT-TYPE    
  RowStatus  

agentAuthenticationGroup 1.3.6.1.4.1.4526.1.7.1.2.16
OBJECT IDENTIFIER    

agentAuthenticationListCreate 1.3.6.1.4.1.4526.1.7.1.2.16.1
Authentication List Create If set to a non empty string, creates a new Authentication List for configuration.
OBJECT-TYPE    
  DisplayString Size(1..15)  

agentAuthenticationListTable 1.3.6.1.4.1.4526.1.7.1.2.16.2
MST VLAN table.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentAuthenticationListEntry

agentAuthenticationListEntry 1.3.6.1.4.1.4526.1.7.1.2.16.2.1
MST VLAN entry.
OBJECT-TYPE    
  AgentAuthenticationListEntry  

agentAuthenticationListIndex 1.3.6.1.4.1.4526.1.7.1.2.16.2.1.1
Authenticaiton List Index Unique number used for indexing into this table.
OBJECT-TYPE    
  Unsigned32  

agentAuthenticationListName 1.3.6.1.4.1.4526.1.7.1.2.16.2.1.2
Authenticaiton List Name Unique name used to identify the Authentication List from other tables.
OBJECT-TYPE    
  DisplayString Size(1..15)  

agentAuthenticationListMethod1 1.3.6.1.4.1.4526.1.7.1.2.16.2.1.3
Authenticion List Method 1 Configures the first authentication method to use when this list is specified.
OBJECT-TYPE    
  INTEGER local(1), radius(2), reject(3)  

agentAuthenticationListMethod2 1.3.6.1.4.1.4526.1.7.1.2.16.2.1.4
Authenticion List Method 2 Configures the second authentication method to use when this list is specified.
OBJECT-TYPE    
  INTEGER undefined(1), local(2), radius(3), reject(4)  

agentAuthenticationListMethod3 1.3.6.1.4.1.4526.1.7.1.2.16.2.1.5
Authenticion List Method 3 Configures the third authentication method to use when this list is specified.
OBJECT-TYPE    
  INTEGER undefined(1), local(2), radius(3), reject(4)  

agentAuthenticationListStatus 1.3.6.1.4.1.4526.1.7.1.2.16.2.1.6
The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List destroy(6) - removes the Authentication List.
OBJECT-TYPE    
  RowStatus  

agentUserConfigDefaultAuthenticationList 1.3.6.1.4.1.4526.1.7.1.2.16.3
Default Authentication List This object configures which authentication list to use for users which do not have an Authentication List configured. The list must be configured before setting.
OBJECT-TYPE    
  DisplayString Size(1..15)  

agentUserAuthenticationConfigTable 1.3.6.1.4.1.4526.1.7.1.2.16.4
User Authentication Config Table
OBJECT-TYPE    
  SEQUENCE OF  
    AgentUserAuthenticationConfigEntry

agentUserAuthenticationConfigEntry 1.3.6.1.4.1.4526.1.7.1.2.16.4.1
User Authentication Config Entry
OBJECT-TYPE    
  AgentUserAuthenticationConfigEntry  

agentUserAuthenticationList 1.3.6.1.4.1.4526.1.7.1.2.16.4.1.1
User Authentication List This object configures which authentication list to use for this user. The list must be configured before setting.
OBJECT-TYPE    
  DisplayString Size(1..15)  

agentUserPortConfigTable 1.3.6.1.4.1.4526.1.7.1.2.16.5
User Port Config Table
OBJECT-TYPE    
  SEQUENCE OF  
    AgentUserPortConfigEntry

agentUserPortConfigEntry 1.3.6.1.4.1.4526.1.7.1.2.16.5.1
User Port Config Entry
OBJECT-TYPE    
  AgentUserPortConfigEntry  

agentUserPortSecurity 1.3.6.1.4.1.4526.1.7.1.2.16.5.1.1
User Port Port Security This object configures which ports the user has access to. Ports are indexed based on dot1dBasePort entries in dot1dBasePortTable.
OBJECT-TYPE    
  AgentPortMask  

agentClassOfServiceGroup 1.3.6.1.4.1.4526.1.7.1.2.17
OBJECT IDENTIFIER    

agentClassOfServiceTable 1.3.6.1.4.1.4526.1.7.1.2.17.1
A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentClassOfServiceEntry

agentClassOfServiceEntry 1.3.6.1.4.1.4526.1.7.1.2.17.1.1
A 802.1p priority mapped to a traffic class priority queue.
OBJECT-TYPE    
  AgentClassOfServiceEntry  

agentClassOfServicePriority 1.3.6.1.4.1.4526.1.7.1.2.17.1.1.1
The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port.
OBJECT-TYPE    
  Integer32 0..7  

agentClassOfServiceClass 1.3.6.1.4.1.4526.1.7.1.2.17.1.1.2
Traffic class priority queue the received frame is mapped to.
OBJECT-TYPE    
  Integer32 0..7  

agentSystemGroup 1.3.6.1.4.1.4526.1.7.1.3
OBJECT IDENTIFIER    

agentSaveConfig 1.3.6.1.4.1.4526.1.7.1.3.1
Enable agentSaveConfig will initiate an configuration save to nvram. Disable agentSaveConfig after a configuration save will reset agentSaveConfigStatus back to notInitiated state.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentClearConfig 1.3.6.1.4.1.4526.1.7.1.3.2
clear config to factory defaults
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentClearLags 1.3.6.1.4.1.4526.1.7.1.3.3
clear lag configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentClearLoginSessions 1.3.6.1.4.1.4526.1.7.1.3.4
close all telnet sessions
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentClearPasswords 1.3.6.1.4.1.4526.1.7.1.3.5
reset passwords
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentClearPortStats 1.3.6.1.4.1.4526.1.7.1.3.6
clear all port statistics
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentClearSwitchStats 1.3.6.1.4.1.4526.1.7.1.3.7
clear all switch statistics
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentClearTrapLog 1.3.6.1.4.1.4526.1.7.1.3.8
clear trap log
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentClearVlan 1.3.6.1.4.1.4526.1.7.1.3.9
clear vlan entries
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentResetSystem 1.3.6.1.4.1.4526.1.7.1.3.10
reset the switch
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSaveConfigStatus 1.3.6.1.4.1.4526.1.7.1.3.11
Indicates the current status of an save configuration request.
OBJECT-TYPE    
  INTEGER notInitiated(1), savingInProcess(2), savingComplete(3)  

agentCableTesterGroup 1.3.6.1.4.1.4526.1.7.1.4
OBJECT IDENTIFIER    

agentCableTesterStatus 1.3.6.1.4.1.4526.1.7.1.4.1
Status of the Virtual Cable Tester active(1) - cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set.
OBJECT-TYPE    
  INTEGER active(1), success(2), failure(3), uninitialized(4)  

agentCableTesterIfIndex 1.3.6.1.4.1.4526.1.7.1.4.2
Determines on which port to perform the cable test. Limited to copper based ports.
OBJECT-TYPE    
  Unsigned32  

agentCableTesterCableStatus 1.3.6.1.4.1.4526.1.7.1.4.3
Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress.
OBJECT-TYPE    
  INTEGER normal(1), open(2), short(3), unknown(4)  

agentCableTesterMinimumCableLength 1.3.6.1.4.1.4526.1.7.1.4.4
The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.
OBJECT-TYPE    
  Unsigned32  

agentCableTesterMaximumCableLength 1.3.6.1.4.1.4526.1.7.1.4.5
The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.
OBJECT-TYPE    
  Unsigned32  

agentCableTesterCableFailureLocation 1.3.6.1.4.1.4526.1.7.1.4.6
The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if agentCableTesterStatus is not success(2).
OBJECT-TYPE    
  Unsigned32  

gsm7324SwitchingTraps 1.3.6.1.4.1.4526.1.7.1.50
OBJECT IDENTIFIER    

multipleUsersTrap 1.3.6.1.4.1.4526.1.7.1.50.1
trapMgrMultipleUsersLogTrap.
NOTIFICATION-TYPE    

broadcastStormStartTrap 1.3.6.1.4.1.4526.1.7.1.50.2
trapMgrBCastStormStartLogTrap.
NOTIFICATION-TYPE    

broadcastStormEndTrap 1.3.6.1.4.1.4526.1.7.1.50.3
trapMgrBCastStormEndLogTrap.
NOTIFICATION-TYPE    

linkFailureTrap 1.3.6.1.4.1.4526.1.7.1.50.4
trapMgrLinkFailureLogTrap.
NOTIFICATION-TYPE    

vlanRequestFailureTrap 1.3.6.1.4.1.4526.1.7.1.50.5
trapMgrVlanRequestFailureLogTrap
NOTIFICATION-TYPE    

vlanDeleteLastTrap 1.3.6.1.4.1.4526.1.7.1.50.6
trapMgrLastVlanDeleteLastLogTrap
NOTIFICATION-TYPE    

vlanDefaultCfgFailureTrap 1.3.6.1.4.1.4526.1.7.1.50.7
trapMgrDefaultVlanCfgFailureLogTrap
NOTIFICATION-TYPE    

vlanRestoreFailureTrap 1.3.6.1.4.1.4526.1.7.1.50.8
trapMgrVlanRestoreFailureLogTrap
NOTIFICATION-TYPE    

fanFailureTrap 1.3.6.1.4.1.4526.1.7.1.50.9
trapMgrFanFailureLogTrap.
NOTIFICATION-TYPE    

stpInstanceNewRootTrap 1.3.6.1.4.1.4526.1.7.1.50.10
trapMgrStpInstanceNewRootTrap
NOTIFICATION-TYPE    

stpInstanceTopologyChangeTrap 1.3.6.1.4.1.4526.1.7.1.50.11
trapMgrStpInstanceTopologyChange
NOTIFICATION-TYPE    

powerSupplyStatusChangeTrap 1.3.6.1.4.1.4526.1.7.1.50.12
powerSupplyStatusChangeTrap
NOTIFICATION-TYPE