GE-PARALLELUPS

File: GE-PARALLELUPS.mib (813596 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
OBJECT-IDENTITY Counter32 Gauge32
Integer32 enterprises IpAddress
DisplayString TimeStamp TimeInterval
TestAndIncr AutonomousType TEXTUAL-CONVENTION

Defined Types

PositiveInteger32  
This data type is a non-zero and non-negative value.
TEXTUAL-CONVENTION    
  Integer32 1..2147483647  

NonNegativeInteger32  
This data type is a non-negative value.
TEXTUAL-CONVENTION    
  Integer32 0..2147483647  

UpsInputEntry-gen  
SEQUENCE    
  upsInputLineIndex-gen PositiveInteger32
  upsInputFrequency-gen NonNegativeInteger32
  upsInputVoltage-gen NonNegativeInteger32
  upsInputCurrent-gen NonNegativeInteger32
  upsInputTruePower-gen NonNegativeInteger32
  upsInputVoltageMin-gen NonNegativeInteger32
  upsInputVoltageMax-gen NonNegativeInteger32

UpsOutputEntry-gen  
SEQUENCE    
  upsOutputLineIndex-gen PositiveInteger32
  upsOutputVoltage-gen NonNegativeInteger32
  upsOutputCurrent-gen NonNegativeInteger32
  upsOutputPower-gen NonNegativeInteger32
  upsOutputPercentLoad-gen Integer32

UpsBypassEntry-gen  
SEQUENCE    
  upsBypassLineIndex-gen PositiveInteger32
  upsBypassVoltage-gen NonNegativeInteger32
  upsBypassCurrent-gen NonNegativeInteger32
  upsBypassPower-gen NonNegativeInteger32

UpsAlarmEntry-gen  
SEQUENCE    
  upsAlarmId-gen PositiveInteger32
  upsAlarmDescr-gen AutonomousType
  upsAlarmTime-gen TimeStamp

UpsReceptacleEntry-gen  
SEQUENCE    
  upsReceptacleLineIndex-gen PositiveInteger32
  upsReceptacleOnOff-gen Integer32

UpsEventEntry-gen  
SEQUENCE    
  upsEventLineIndex-gen PositiveInteger32
  upsEventCode-gen Integer32
  upsEventStatus-gen NonNegativeInteger32
  upsEventTime-gen NonNegativeInteger32

UpsParameterEntry-gen  
SEQUENCE    
  upsParameterLineIndex-gen PositiveInteger32
  upsParameterValue-gen Integer32

IoInterfaceInputEntry-First  
SEQUENCE    
  ioInterfaceInputLineIndex-First PositiveInteger32
  ioInterfaceInputDescription-First DisplayString
  ioInterfaceInputStatus-First Integer32
  ioInterfaceEdgeMode-First Integer32
  ioInterfaceAlarmMask-First Integer32

IoInterfaceOutputEntry-First  
SEQUENCE    
  ioInterfaceOutputLineIndex-First PositiveInteger32
  ioInterfaceOutputDescription-First DisplayString
  ioInterfaceOutputStatus-First Integer32

IoInterfaceAnalogueEntry-First  
SEQUENCE    
  ioInterfaceAnalogueLineIndex-First PositiveInteger32
  ioInterfaceAnalogueDescription-First DisplayString
  ioInterfaceAnalogueStatus-First Integer32
  ioInterfaceAnalogueLowThreshold-First Integer32
  ioInterfaceAnalogueHighThreshold-First Integer32
  ioInterfaceAnalogueResetLowThreshold-First Integer32
  ioInterfaceAnalogueResetHighThreshold-First Integer32

IoInterfaceInputEntry-Second  
SEQUENCE    
  ioInterfaceInputLineIndex-Second PositiveInteger32
  ioInterfaceInputDescription-Second DisplayString
  ioInterfaceInputStatus-Second Integer32
  ioInterfaceEdgeMode-Second Integer32
  ioInterfaceAlarmMask-Second Integer32
  ioInterfaceAlarmDelay-Second NonNegativeInteger32

IoInterfaceOutputEntry-Second  
SEQUENCE    
  ioInterfaceOutputLineIndex-Second PositiveInteger32
  ioInterfaceOutputDescription-Second DisplayString
  ioInterfaceOutputStatus-Second Integer32

IoInterfaceAnalogueEntry-Second  
SEQUENCE    
  ioInterfaceAnalogueLineIndex-Second PositiveInteger32
  ioInterfaceAnalogueDescription-Second DisplayString
  ioInterfaceAnalogueStatus-Second Integer32
  ioInterfaceAnalogueLowThreshold-Second Integer32
  ioInterfaceAnalogueHighThreshold-Second Integer32
  ioInterfaceAnalogueResetLowThreshold-Second Integer32
  ioInterfaceAnalogueResetHighThreshold-Second Integer32

IoInterfaceInputEntry-Third  
SEQUENCE    
  ioInterfaceInputLineIndex-Third PositiveInteger32
  ioInterfaceInputDescription-Third DisplayString
  ioInterfaceInputStatus-Third Integer32
  ioInterfaceEdgeMode-Third Integer32
  ioInterfaceAlarmMask-Third Integer32
  ioInterfaceAlarmDelay-Third NonNegativeInteger32

IoInterfaceOutputEntry-Third  
SEQUENCE    
  ioInterfaceOutputLineIndex-Third PositiveInteger32
  ioInterfaceOutputDescription-Third DisplayString
  ioInterfaceOutputStatus-Third Integer32

IoInterfaceAnalogueEntry-Third  
SEQUENCE    
  ioInterfaceAnalogueLineIndex-Third PositiveInteger32
  ioInterfaceAnalogueDescription-Third DisplayString
  ioInterfaceAnalogueStatus-Third Integer32
  ioInterfaceAnalogueLowThreshold-Third Integer32
  ioInterfaceAnalogueHighThreshold-Third Integer32
  ioInterfaceAnalogueResetLowThreshold-Third Integer32
  ioInterfaceAnalogueResetHighThreshold-Third Integer32

IoInterfaceInputEntry-Fourth  
SEQUENCE    
  ioInterfaceInputLineIndex-Fourth PositiveInteger32
  ioInterfaceInputDescription-Fourth DisplayString
  ioInterfaceInputStatus-Fourth Integer32
  ioInterfaceEdgeMode-Fourth Integer32
  ioInterfaceAlarmMask-Fourth Integer32
  ioInterfaceAlarmDelay-Fourth NonNegativeInteger32

IoInterfaceOutputEntry-Fourth  
SEQUENCE    
  ioInterfaceOutputLineIndex-Fourth PositiveInteger32
  ioInterfaceOutputDescription-Fourth DisplayString
  ioInterfaceOutputStatus-Fourth Integer32

IoInterfaceAnalogueEntry-Fourth  
SEQUENCE    
  ioInterfaceAnalogueLineIndex-Fourth PositiveInteger32
  ioInterfaceAnalogueDescription-Fourth DisplayString
  ioInterfaceAnalogueStatus-Fourth Integer32
  ioInterfaceAnalogueLowThreshold-Fourth Integer32
  ioInterfaceAnalogueHighThreshold-Fourth Integer32
  ioInterfaceAnalogueResetLowThreshold-Fourth Integer32
  ioInterfaceAnalogueResetHighThreshold-Fourth Integer32

IoInterfaceInputEntry-Fifth  
SEQUENCE    
  ioInterfaceInputLineIndex-Fifth PositiveInteger32
  ioInterfaceInputDescription-Fifth DisplayString
  ioInterfaceInputStatus-Fifth Integer32
  ioInterfaceEdgeMode-Fifth Integer32
  ioInterfaceAlarmMask-Fifth Integer32
  ioInterfaceAlarmDelay-Fifth NonNegativeInteger32

IoInterfaceOutputEntry-Fifth  
SEQUENCE    
  ioInterfaceOutputLineIndex-Fifth PositiveInteger32
  ioInterfaceOutputDescription-Fifth DisplayString
  ioInterfaceOutputStatus-Fifth Integer32

IoInterfaceAnalogueEntry-Fifth  
SEQUENCE    
  ioInterfaceAnalogueLineIndex-Fifth PositiveInteger32
  ioInterfaceAnalogueDescription-Fifth DisplayString
  ioInterfaceAnalogueStatus-Fifth Integer32
  ioInterfaceAnalogueLowThreshold-Fifth Integer32
  ioInterfaceAnalogueHighThreshold-Fifth Integer32
  ioInterfaceAnalogueResetLowThreshold-Fifth Integer32
  ioInterfaceAnalogueResetHighThreshold-Fifth Integer32

IoInterfaceInputEntry-Sixth  
SEQUENCE    
  ioInterfaceInputLineIndex-Sixth PositiveInteger32
  ioInterfaceInputDescription-Sixth DisplayString
  ioInterfaceInputStatus-Sixth Integer32
  ioInterfaceEdgeMode-Sixth Integer32
  ioInterfaceAlarmMask-Sixth Integer32
  ioInterfaceAlarmDelay-Sixth NonNegativeInteger32

IoInterfaceOutputEntry-Sixth  
SEQUENCE    
  ioInterfaceOutputLineIndex-Sixth PositiveInteger32
  ioInterfaceOutputDescription-Sixth DisplayString
  ioInterfaceOutputStatus-Sixth Integer32

IoInterfaceAnalogueEntry-Sixth  
SEQUENCE    
  ioInterfaceAnalogueLineIndex-Sixth PositiveInteger32
  ioInterfaceAnalogueDescription-Sixth DisplayString
  ioInterfaceAnalogueStatus-Sixth Integer32
  ioInterfaceAnalogueLowThreshold-Sixth Integer32
  ioInterfaceAnalogueHighThreshold-Sixth Integer32
  ioInterfaceAnalogueResetLowThreshold-Sixth Integer32
  ioInterfaceAnalogueResetHighThreshold-Sixth Integer32

IoInterfaceInputEntry-Seventh  
SEQUENCE    
  ioInterfaceInputLineIndex-Seventh PositiveInteger32
  ioInterfaceInputDescription-Seventh DisplayString
  ioInterfaceInputStatus-Seventh Integer32
  ioInterfaceEdgeMode-Seventh Integer32
  ioInterfaceAlarmMask-Seventh Integer32
  ioInterfaceAlarmDelay-Seventh NonNegativeInteger32

IoInterfaceOutputEntry-Seventh  
SEQUENCE    
  ioInterfaceOutputLineIndex-Seventh PositiveInteger32
  ioInterfaceOutputDescription-Seventh DisplayString
  ioInterfaceOutputStatus-Seventh Integer32

IoInterfaceAnalogueEntry-Seventh  
SEQUENCE    
  ioInterfaceAnalogueLineIndex-Seventh PositiveInteger32
  ioInterfaceAnalogueDescription-Seventh DisplayString
  ioInterfaceAnalogueStatus-Seventh Integer32
  ioInterfaceAnalogueLowThreshold-Seventh Integer32
  ioInterfaceAnalogueHighThreshold-Seventh Integer32
  ioInterfaceAnalogueResetLowThreshold-Seventh Integer32
  ioInterfaceAnalogueResetHighThreshold-Seventh Integer32

IoInterfaceInputEntry-Eighth  
SEQUENCE    
  ioInterfaceInputLineIndex-Eighth PositiveInteger32
  ioInterfaceInputDescription-Eighth DisplayString
  ioInterfaceInputStatus-Eighth Integer32
  ioInterfaceEdgeMode-Eighth Integer32
  ioInterfaceAlarmMask-Eighth Integer32
  ioInterfaceAlarmDelay-Eighth NonNegativeInteger32

IoInterfaceOutputEntry-Eighth  
SEQUENCE    
  ioInterfaceOutputLineIndex-Eighth PositiveInteger32
  ioInterfaceOutputDescription-Eighth DisplayString
  ioInterfaceOutputStatus-Eighth Integer32

IoInterfaceAnalogueEntry-Eighth  
SEQUENCE    
  ioInterfaceAnalogueLineIndex-Eighth PositiveInteger32
  ioInterfaceAnalogueDescription-Eighth DisplayString
  ioInterfaceAnalogueStatus-Eighth Integer32
  ioInterfaceAnalogueLowThreshold-Eighth Integer32
  ioInterfaceAnalogueHighThreshold-Eighth Integer32
  ioInterfaceAnalogueResetLowThreshold-Eighth Integer32
  ioInterfaceAnalogueResetHighThreshold-Eighth Integer32

GeModemInitStringEntry  
SEQUENCE    
  geModemInitStringLineIndex PositiveInteger32
  geModemInitstring DisplayString

GeModemPhoneNumberEntry  
SEQUENCE    
  geModemPhoneNumberLineIndex PositiveInteger32
  geModemPhoneNumber DisplayString

GeClientUPSEntry  
SEQUENCE    
  geClientUPSLineIndex PositiveInteger32
  geClientUPSName DisplayString
  geClientUPSCommunicationType Integer32
  geClientUPSCommunicationPort DisplayString
  geClientUPSReadCommName DisplayString
  geClientUPSWriteCommName DisplayString
  geClientUPSCommRetries NonNegativeInteger32
  geClientAlarmManagement Integer32
  geClientPreDelay NonNegativeInteger32
  geClientSystemShutdown Integer32
  geClientRuntime NonNegativeInteger32
  geClientUPSShutdown Integer32
  geClientMaxScriptExecutionTime NonNegativeInteger32
  geClientGraceperiod NonNegativeInteger32

GeClientTestEntry  
SEQUENCE    
  geClientTestLineIndex PositiveInteger32
  geClientTestId Integer32
  geClientTestDayTime Integer32
  geClientTestWeekDay Integer32
  geClientTestMonthDay Integer32

GeClientShutdownEntry  
SEQUENCE    
  geClientShutdownLineIndex PositiveInteger32
  geClientShutdownDelay Integer32
  geClientShutdownDuration Integer32
  geClientShutdownDayTime Integer32
  geClientShutdownWeekDay Integer32
  geClientShutdownMonthDay Integer32
  geClientShutdownPreWarnTime Integer32

GeAgentTrapEntry  
SEQUENCE    
  geAgentTrapLineIndex PositiveInteger32
  geAgentTrapAddress DisplayString
  geAgentTrapCommunity DisplayString
  geAgentTrapPort Integer32

UpsInputEntry-first  
SEQUENCE    
  upsInputLineIndex-first PositiveInteger32
  upsInputFrequency-first NonNegativeInteger32
  upsInputVoltage-first NonNegativeInteger32
  upsInputCurrent-first NonNegativeInteger32
  upsInputTruePower-first NonNegativeInteger32
  upsInputVoltageMin-first NonNegativeInteger32
  upsInputVoltageMax-first NonNegativeInteger32

UpsOutputEntry-first  
SEQUENCE    
  upsOutputLineIndex-first PositiveInteger32
  upsOutputVoltage-first NonNegativeInteger32
  upsOutputCurrent-first NonNegativeInteger32
  upsOutputPower-first NonNegativeInteger32
  upsOutputPercentLoad-first Integer32

UpsBypassEntry-first  
SEQUENCE    
  upsBypassLineIndex-first PositiveInteger32
  upsBypassVoltage-first NonNegativeInteger32
  upsBypassCurrent-first NonNegativeInteger32
  upsBypassPower-first NonNegativeInteger32

UpsAlarmEntry-first  
SEQUENCE    
  upsAlarmId-first PositiveInteger32
  upsAlarmDescr-first AutonomousType
  upsAlarmTime-first TimeStamp

UpsReceptacleEntry-first  
SEQUENCE    
  upsReceptacleLineIndex-first PositiveInteger32
  upsReceptacleOnOff-first Integer32

UpsEventEntry-first  
SEQUENCE    
  upsEventLineIndex-first PositiveInteger32
  upsEventCode-first Integer32
  upsEventStatus-first NonNegativeInteger32
  upsEventTime-first NonNegativeInteger32

UpsParameterEntry-first  
SEQUENCE    
  upsParameterLineIndex-first PositiveInteger32
  upsParameterValue-first Integer32

UpsInputEntry-second  
SEQUENCE    
  upsInputLineIndex-second PositiveInteger32
  upsInputFrequency-second NonNegativeInteger32
  upsInputVoltage-second NonNegativeInteger32
  upsInputCurrent-second NonNegativeInteger32
  upsInputTruePower-second NonNegativeInteger32
  upsInputVoltageMin-second NonNegativeInteger32
  upsInputVoltageMax-second NonNegativeInteger32

UpsOutputEntry-second  
SEQUENCE    
  upsOutputLineIndex-second PositiveInteger32
  upsOutputVoltage-second NonNegativeInteger32
  upsOutputCurrent-second NonNegativeInteger32
  upsOutputPower-second NonNegativeInteger32
  upsOutputPercentLoad-second Integer32

UpsBypassEntry-second  
SEQUENCE    
  upsBypassLineIndex-second PositiveInteger32
  upsBypassVoltage-second NonNegativeInteger32
  upsBypassCurrent-second NonNegativeInteger32
  upsBypassPower-second NonNegativeInteger32

UpsAlarmEntry-second  
SEQUENCE    
  upsAlarmId-second PositiveInteger32
  upsAlarmDescr-second AutonomousType
  upsAlarmTime-second TimeStamp

UpsReceptacleEntry-second  
SEQUENCE    
  upsReceptacleLineIndex-second PositiveInteger32
  upsReceptacleOnOff-second Integer32

UpsEventEntry-second  
SEQUENCE    
  upsEventLineIndex-second PositiveInteger32
  upsEventCode-second Integer32
  upsEventStatus-second NonNegativeInteger32
  upsEventTime-second NonNegativeInteger32

UpsParameterEntry-second  
SEQUENCE    
  upsParameterLineIndex-second PositiveInteger32
  upsParameterValue-second Integer32

UpsInputEntry-third  
SEQUENCE    
  upsInputLineIndex-third PositiveInteger32
  upsInputFrequency-third NonNegativeInteger32
  upsInputVoltage-third NonNegativeInteger32
  upsInputCurrent-third NonNegativeInteger32
  upsInputTruePower-third NonNegativeInteger32
  upsInputVoltageMin-third NonNegativeInteger32
  upsInputVoltageMax-third NonNegativeInteger32

UpsOutputEntry-third  
SEQUENCE    
  upsOutputLineIndex-third PositiveInteger32
  upsOutputVoltage-third NonNegativeInteger32
  upsOutputCurrent-third NonNegativeInteger32
  upsOutputPower-third NonNegativeInteger32
  upsOutputPercentLoad-third Integer32

UpsBypassEntry-third  
SEQUENCE    
  upsBypassLineIndex-third PositiveInteger32
  upsBypassVoltage-third NonNegativeInteger32
  upsBypassCurrent-third NonNegativeInteger32
  upsBypassPower-third NonNegativeInteger32

UpsAlarmEntry-third  
SEQUENCE    
  upsAlarmId-third PositiveInteger32
  upsAlarmDescr-third AutonomousType
  upsAlarmTime-third TimeStamp

UpsReceptacleEntry-third  
SEQUENCE    
  upsReceptacleLineIndex-third PositiveInteger32
  upsReceptacleOnOff-third Integer32

UpsEventEntry-third  
SEQUENCE    
  upsEventLineIndex-third PositiveInteger32
  upsEventCode-third Integer32
  upsEventStatus-third NonNegativeInteger32
  upsEventTime-third NonNegativeInteger32

UpsParameterEntry-third  
SEQUENCE    
  upsParameterLineIndex-third PositiveInteger32
  upsParameterValue-third Integer32

UpsInputEntry-fourth  
SEQUENCE    
  upsInputLineIndex-fourth PositiveInteger32
  upsInputFrequency-fourth NonNegativeInteger32
  upsInputVoltage-fourth NonNegativeInteger32
  upsInputCurrent-fourth NonNegativeInteger32
  upsInputTruePower-fourth NonNegativeInteger32
  upsInputVoltageMin-fourth NonNegativeInteger32
  upsInputVoltageMax-fourth NonNegativeInteger32

UpsOutputEntry-fourth  
SEQUENCE    
  upsOutputLineIndex-fourth PositiveInteger32
  upsOutputVoltage-fourth NonNegativeInteger32
  upsOutputCurrent-fourth NonNegativeInteger32
  upsOutputPower-fourth NonNegativeInteger32
  upsOutputPercentLoad-fourth Integer32

UpsBypassEntry-fourth  
SEQUENCE    
  upsBypassLineIndex-fourth PositiveInteger32
  upsBypassVoltage-fourth NonNegativeInteger32
  upsBypassCurrent-fourth NonNegativeInteger32
  upsBypassPower-fourth NonNegativeInteger32

UpsAlarmEntry-fourth  
SEQUENCE    
  upsAlarmId-fourth PositiveInteger32
  upsAlarmDescr-fourth AutonomousType
  upsAlarmTime-fourth TimeStamp

UpsReceptacleEntry-fourth  
SEQUENCE    
  upsReceptacleLineIndex-fourth PositiveInteger32
  upsReceptacleOnOff-fourth Integer32

UpsEventEntry-fourth  
SEQUENCE    
  upsEventLineIndex-fourth PositiveInteger32
  upsEventCode-fourth Integer32
  upsEventStatus-fourth NonNegativeInteger32
  upsEventTime-fourth NonNegativeInteger32

UpsParameterEntry-fourth  
SEQUENCE    
  upsParameterLineIndex-fourth PositiveInteger32
  upsParameterValue-fourth Integer32

UpsInputEntry-fifth  
SEQUENCE    
  upsInputLineIndex-fifth PositiveInteger32
  upsInputFrequency-fifth NonNegativeInteger32
  upsInputVoltage-fifth NonNegativeInteger32
  upsInputCurrent-fifth NonNegativeInteger32
  upsInputTruePower-fifth NonNegativeInteger32
  upsInputVoltageMin-fifth NonNegativeInteger32
  upsInputVoltageMax-fifth NonNegativeInteger32

UpsOutputEntry-fifth  
SEQUENCE    
  upsOutputLineIndex-fifth PositiveInteger32
  upsOutputVoltage-fifth NonNegativeInteger32
  upsOutputCurrent-fifth NonNegativeInteger32
  upsOutputPower-fifth NonNegativeInteger32
  upsOutputPercentLoad-fifth Integer32

UpsBypassEntry-fifth  
SEQUENCE    
  upsBypassLineIndex-fifth PositiveInteger32
  upsBypassVoltage-fifth NonNegativeInteger32
  upsBypassCurrent-fifth NonNegativeInteger32
  upsBypassPower-fifth NonNegativeInteger32

UpsAlarmEntry-fifth  
SEQUENCE    
  upsAlarmId-fifth PositiveInteger32
  upsAlarmDescr-fifth AutonomousType
  upsAlarmTime-fifth TimeStamp

UpsReceptacleEntry-fifth  
SEQUENCE    
  upsReceptacleLineIndex-fifth PositiveInteger32
  upsReceptacleOnOff-fifth Integer32

UpsEventEntry-fifth  
SEQUENCE    
  upsEventLineIndex-fifth PositiveInteger32
  upsEventCode-fifth Integer32
  upsEventStatus-fifth NonNegativeInteger32
  upsEventTime-fifth NonNegativeInteger32

UpsParameterEntry-fifth  
SEQUENCE    
  upsParameterLineIndex-fifth PositiveInteger32
  upsParameterValue-fifth Integer32

UpsInputEntry-sixth  
SEQUENCE    
  upsInputLineIndex-sixth PositiveInteger32
  upsInputFrequency-sixth NonNegativeInteger32
  upsInputVoltage-sixth NonNegativeInteger32
  upsInputCurrent-sixth NonNegativeInteger32
  upsInputTruePower-sixth NonNegativeInteger32
  upsInputVoltageMin-sixth NonNegativeInteger32
  upsInputVoltageMax-sixth NonNegativeInteger32

UpsOutputEntry-sixth  
SEQUENCE    
  upsOutputLineIndex-sixth PositiveInteger32
  upsOutputVoltage-sixth NonNegativeInteger32
  upsOutputCurrent-sixth NonNegativeInteger32
  upsOutputPower-sixth NonNegativeInteger32
  upsOutputPercentLoad-sixth Integer32

UpsBypassEntry-sixth  
SEQUENCE    
  upsBypassLineIndex-sixth PositiveInteger32
  upsBypassVoltage-sixth NonNegativeInteger32
  upsBypassCurrent-sixth NonNegativeInteger32
  upsBypassPower-sixth NonNegativeInteger32

UpsAlarmEntry-sixth  
SEQUENCE    
  upsAlarmId-sixth PositiveInteger32
  upsAlarmDescr-sixth AutonomousType
  upsAlarmTime-sixth TimeStamp

UpsReceptacleEntry-sixth  
SEQUENCE    
  upsReceptacleLineIndex-sixth PositiveInteger32
  upsReceptacleOnOff-sixth Integer32

UpsEventEntry-sixth  
SEQUENCE    
  upsEventLineIndex-sixth PositiveInteger32
  upsEventCode-sixth Integer32
  upsEventStatus-sixth NonNegativeInteger32
  upsEventTime-sixth NonNegativeInteger32

UpsParameterEntry-sixth  
SEQUENCE    
  upsParameterLineIndex-sixth PositiveInteger32
  upsParameterValue-sixth Integer32

UpsInputEntry-seventh  
SEQUENCE    
  upsInputLineIndex-seventh PositiveInteger32
  upsInputFrequency-seventh NonNegativeInteger32
  upsInputVoltage-seventh NonNegativeInteger32
  upsInputCurrent-seventh NonNegativeInteger32
  upsInputTruePower-seventh NonNegativeInteger32
  upsInputVoltageMin-seventh NonNegativeInteger32
  upsInputVoltageMax-seventh NonNegativeInteger32

UpsOutputEntry-seventh  
SEQUENCE    
  upsOutputLineIndex-seventh PositiveInteger32
  upsOutputVoltage-seventh NonNegativeInteger32
  upsOutputCurrent-seventh NonNegativeInteger32
  upsOutputPower-seventh NonNegativeInteger32
  upsOutputPercentLoad-seventh Integer32

UpsBypassEntry-seventh  
SEQUENCE    
  upsBypassLineIndex-seventh PositiveInteger32
  upsBypassVoltage-seventh NonNegativeInteger32
  upsBypassCurrent-seventh NonNegativeInteger32
  upsBypassPower-seventh NonNegativeInteger32

UpsAlarmEntry-seventh  
SEQUENCE    
  upsAlarmId-seventh PositiveInteger32
  upsAlarmDescr-seventh AutonomousType
  upsAlarmTime-seventh TimeStamp

UpsReceptacleEntry-seventh  
SEQUENCE    
  upsReceptacleLineIndex-seventh PositiveInteger32
  upsReceptacleOnOff-seventh Integer32

UpsEventEntry-seventh  
SEQUENCE    
  upsEventLineIndex-seventh PositiveInteger32
  upsEventCode-seventh Integer32
  upsEventStatus-seventh NonNegativeInteger32
  upsEventTime-seventh NonNegativeInteger32

UpsParameterEntry-seventh  
SEQUENCE    
  upsParameterLineIndex-seventh PositiveInteger32
  upsParameterValue-seventh Integer32

UpsInputEntry-eighth  
SEQUENCE    
  upsInputLineIndex-eighth PositiveInteger32
  upsInputFrequency-eighth NonNegativeInteger32
  upsInputVoltage-eighth NonNegativeInteger32
  upsInputCurrent-eighth NonNegativeInteger32
  upsInputTruePower-eighth NonNegativeInteger32
  upsInputVoltageMin-eighth NonNegativeInteger32
  upsInputVoltageMax-eighth NonNegativeInteger32

UpsOutputEntry-eighth  
SEQUENCE    
  upsOutputLineIndex-eighth PositiveInteger32
  upsOutputVoltage-eighth NonNegativeInteger32
  upsOutputCurrent-eighth NonNegativeInteger32
  upsOutputPower-eighth NonNegativeInteger32
  upsOutputPercentLoad-eighth Integer32

UpsBypassEntry-eighth  
SEQUENCE    
  upsBypassLineIndex-eighth PositiveInteger32
  upsBypassVoltage-eighth NonNegativeInteger32
  upsBypassCurrent-eighth NonNegativeInteger32
  upsBypassPower-eighth NonNegativeInteger32

UpsAlarmEntry-eighth  
SEQUENCE    
  upsAlarmId-eighth PositiveInteger32
  upsAlarmDescr-eighth AutonomousType
  upsAlarmTime-eighth TimeStamp

UpsReceptacleEntry-eighth  
SEQUENCE    
  upsReceptacleLineIndex-eighth PositiveInteger32
  upsReceptacleOnOff-eighth Integer32

UpsEventEntry-eighth  
SEQUENCE    
  upsEventLineIndex-eighth PositiveInteger32
  upsEventCode-eighth Integer32
  upsEventStatus-eighth NonNegativeInteger32
  upsEventTime-eighth NonNegativeInteger32

UpsParameterEntry-eighth  
SEQUENCE    
  upsParameterLineIndex-eighth PositiveInteger32
  upsParameterValue-eighth Integer32

Defined Values

imv 1.3.6.1.4.1.818
OBJECT IDENTIFIER    

geHardware 1.3.6.1.4.1.818.1
OBJECT IDENTIFIER    

geSoftware 1.3.6.1.4.1.818.2
OBJECT IDENTIFIER    

geAgent 1.3.6.1.4.1.818.3
OBJECT IDENTIFIER    

geUPS 1.3.6.1.4.1.818.1.1
OBJECT IDENTIFIER    

geGenericUPS 1.3.6.1.4.1.818.1.1.10
OBJECT IDENTIFIER    

geFirstUPS 1.3.6.1.4.1.818.1.1.11
OBJECT IDENTIFIER    

geSecondUPS 1.3.6.1.4.1.818.1.1.12
OBJECT IDENTIFIER    

geThirdUPS 1.3.6.1.4.1.818.1.1.13
OBJECT IDENTIFIER    

geFourthUPS 1.3.6.1.4.1.818.1.1.14
OBJECT IDENTIFIER    

geFifthUPS 1.3.6.1.4.1.818.1.1.15
OBJECT IDENTIFIER    

geSixthUPS 1.3.6.1.4.1.818.1.1.16
OBJECT IDENTIFIER    

geSeventhUPS 1.3.6.1.4.1.818.1.1.17
OBJECT IDENTIFIER    

geEighthUPS 1.3.6.1.4.1.818.1.1.18
OBJECT IDENTIFIER    

upsIdent-gen 1.3.6.1.4.1.818.1.1.10.1
OBJECT IDENTIFIER    

upsBattery-gen 1.3.6.1.4.1.818.1.1.10.2
OBJECT IDENTIFIER    

upsInput-gen 1.3.6.1.4.1.818.1.1.10.3
OBJECT IDENTIFIER    

upsOutput-gen 1.3.6.1.4.1.818.1.1.10.4
OBJECT IDENTIFIER    

upsBypass-gen 1.3.6.1.4.1.818.1.1.10.5
OBJECT IDENTIFIER    

upsAlarm-gen 1.3.6.1.4.1.818.1.1.10.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-gen 1.3.6.1.4.1.818.1.1.10.6.3
OBJECT IDENTIFIER    

upsTest-gen 1.3.6.1.4.1.818.1.1.10.7
OBJECT IDENTIFIER    

upsWellKnownTests-gen 1.3.6.1.4.1.818.1.1.10.7.7
OBJECT IDENTIFIER    

upsControl-gen 1.3.6.1.4.1.818.1.1.10.8
OBJECT IDENTIFIER    

upsConfig-gen 1.3.6.1.4.1.818.1.1.10.9
OBJECT IDENTIFIER    

upsGetSet-gen 1.3.6.1.4.1.818.1.1.10.10
OBJECT IDENTIFIER    

geUPSTraps-gen 1.3.6.1.4.1.818.1.1.10.11
OBJECT IDENTIFIER    

upsIdent-first 1.3.6.1.4.1.818.1.1.11.1
OBJECT IDENTIFIER    

upsBattery-first 1.3.6.1.4.1.818.1.1.11.2
OBJECT IDENTIFIER    

upsInput-first 1.3.6.1.4.1.818.1.1.11.3
OBJECT IDENTIFIER    

upsOutput-first 1.3.6.1.4.1.818.1.1.11.4
OBJECT IDENTIFIER    

upsBypass-first 1.3.6.1.4.1.818.1.1.11.5
OBJECT IDENTIFIER    

upsAlarm-first 1.3.6.1.4.1.818.1.1.11.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-first 1.3.6.1.4.1.818.1.1.11.6.3
OBJECT IDENTIFIER    

upsTest-first 1.3.6.1.4.1.818.1.1.11.7
OBJECT IDENTIFIER    

upsWellKnownTests-first 1.3.6.1.4.1.818.1.1.11.7.7
OBJECT IDENTIFIER    

upsControl-first 1.3.6.1.4.1.818.1.1.11.8
OBJECT IDENTIFIER    

upsConfig-first 1.3.6.1.4.1.818.1.1.11.9
OBJECT IDENTIFIER    

upsGetSet-first 1.3.6.1.4.1.818.1.1.11.10
OBJECT IDENTIFIER    

geUPSTraps-first 1.3.6.1.4.1.818.1.1.11.11
OBJECT IDENTIFIER    

upsIdent-second 1.3.6.1.4.1.818.1.1.12.1
OBJECT IDENTIFIER    

upsBattery-second 1.3.6.1.4.1.818.1.1.12.2
OBJECT IDENTIFIER    

upsInput-second 1.3.6.1.4.1.818.1.1.12.3
OBJECT IDENTIFIER    

upsOutput-second 1.3.6.1.4.1.818.1.1.12.4
OBJECT IDENTIFIER    

upsBypass-second 1.3.6.1.4.1.818.1.1.12.5
OBJECT IDENTIFIER    

upsAlarm-second 1.3.6.1.4.1.818.1.1.12.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-second 1.3.6.1.4.1.818.1.1.12.6.3
OBJECT IDENTIFIER    

upsTest-second 1.3.6.1.4.1.818.1.1.12.7
OBJECT IDENTIFIER    

upsWellKnownTests-second 1.3.6.1.4.1.818.1.1.12.7.7
OBJECT IDENTIFIER    

upsControl-second 1.3.6.1.4.1.818.1.1.12.8
OBJECT IDENTIFIER    

upsConfig-second 1.3.6.1.4.1.818.1.1.12.9
OBJECT IDENTIFIER    

upsGetSet-second 1.3.6.1.4.1.818.1.1.12.10
OBJECT IDENTIFIER    

geUPSTraps-second 1.3.6.1.4.1.818.1.1.12.11
OBJECT IDENTIFIER    

upsIdent-third 1.3.6.1.4.1.818.1.1.13.1
OBJECT IDENTIFIER    

upsBattery-third 1.3.6.1.4.1.818.1.1.13.2
OBJECT IDENTIFIER    

upsInput-third 1.3.6.1.4.1.818.1.1.13.3
OBJECT IDENTIFIER    

upsOutput-third 1.3.6.1.4.1.818.1.1.13.4
OBJECT IDENTIFIER    

upsBypass-third 1.3.6.1.4.1.818.1.1.13.5
OBJECT IDENTIFIER    

upsAlarm-third 1.3.6.1.4.1.818.1.1.13.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-third 1.3.6.1.4.1.818.1.1.13.6.3
OBJECT IDENTIFIER    

upsTest-third 1.3.6.1.4.1.818.1.1.13.7
OBJECT IDENTIFIER    

upsWellKnownTests-third 1.3.6.1.4.1.818.1.1.13.7.7
OBJECT IDENTIFIER    

upsControl-third 1.3.6.1.4.1.818.1.1.13.8
OBJECT IDENTIFIER    

upsConfig-third 1.3.6.1.4.1.818.1.1.13.9
OBJECT IDENTIFIER    

upsGetSet-third 1.3.6.1.4.1.818.1.1.13.10
OBJECT IDENTIFIER    

geUPSTraps-third 1.3.6.1.4.1.818.1.1.13.11
OBJECT IDENTIFIER    

upsIdent-fourth 1.3.6.1.4.1.818.1.1.14.1
OBJECT IDENTIFIER    

upsBattery-fourth 1.3.6.1.4.1.818.1.1.14.2
OBJECT IDENTIFIER    

upsInput-fourth 1.3.6.1.4.1.818.1.1.14.3
OBJECT IDENTIFIER    

upsOutput-fourth 1.3.6.1.4.1.818.1.1.14.4
OBJECT IDENTIFIER    

upsBypass-fourth 1.3.6.1.4.1.818.1.1.14.5
OBJECT IDENTIFIER    

upsAlarm-fourth 1.3.6.1.4.1.818.1.1.14.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-fourth 1.3.6.1.4.1.818.1.1.14.6.3
OBJECT IDENTIFIER    

upsTest-fourth 1.3.6.1.4.1.818.1.1.14.7
OBJECT IDENTIFIER    

upsWellKnownTests-fourth 1.3.6.1.4.1.818.1.1.14.7.7
OBJECT IDENTIFIER    

upsControl-fourth 1.3.6.1.4.1.818.1.1.14.8
OBJECT IDENTIFIER    

upsConfig-fourth 1.3.6.1.4.1.818.1.1.14.9
OBJECT IDENTIFIER    

upsGetSet-fourth 1.3.6.1.4.1.818.1.1.14.10
OBJECT IDENTIFIER    

geUPSTraps-fourth 1.3.6.1.4.1.818.1.1.14.11
OBJECT IDENTIFIER    

upsIdent-fifth 1.3.6.1.4.1.818.1.1.15.1
OBJECT IDENTIFIER    

upsBattery-fifth 1.3.6.1.4.1.818.1.1.15.2
OBJECT IDENTIFIER    

upsInput-fifth 1.3.6.1.4.1.818.1.1.15.3
OBJECT IDENTIFIER    

upsOutput-fifth 1.3.6.1.4.1.818.1.1.15.4
OBJECT IDENTIFIER    

upsBypass-fifth 1.3.6.1.4.1.818.1.1.15.5
OBJECT IDENTIFIER    

upsAlarm-fifth 1.3.6.1.4.1.818.1.1.15.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-fifth 1.3.6.1.4.1.818.1.1.15.6.3
OBJECT IDENTIFIER    

upsTest-fifth 1.3.6.1.4.1.818.1.1.15.7
OBJECT IDENTIFIER    

upsWellKnownTests-fifth 1.3.6.1.4.1.818.1.1.15.7.7
OBJECT IDENTIFIER    

upsControl-fifth 1.3.6.1.4.1.818.1.1.15.8
OBJECT IDENTIFIER    

upsConfig-fifth 1.3.6.1.4.1.818.1.1.15.9
OBJECT IDENTIFIER    

upsGetSet-fifth 1.3.6.1.4.1.818.1.1.15.10
OBJECT IDENTIFIER    

geUPSTraps-fifth 1.3.6.1.4.1.818.1.1.15.11
OBJECT IDENTIFIER    

upsIdent-sixth 1.3.6.1.4.1.818.1.1.16.1
OBJECT IDENTIFIER    

upsBattery-sixth 1.3.6.1.4.1.818.1.1.16.2
OBJECT IDENTIFIER    

upsInput-sixth 1.3.6.1.4.1.818.1.1.16.3
OBJECT IDENTIFIER    

upsOutput-sixth 1.3.6.1.4.1.818.1.1.16.4
OBJECT IDENTIFIER    

upsBypass-sixth 1.3.6.1.4.1.818.1.1.16.5
OBJECT IDENTIFIER    

upsAlarm-sixth 1.3.6.1.4.1.818.1.1.16.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-sixth 1.3.6.1.4.1.818.1.1.16.6.3
OBJECT IDENTIFIER    

upsTest-sixth 1.3.6.1.4.1.818.1.1.16.7
OBJECT IDENTIFIER    

upsWellKnownTests-sixth 1.3.6.1.4.1.818.1.1.16.7.7
OBJECT IDENTIFIER    

upsControl-sixth 1.3.6.1.4.1.818.1.1.16.8
OBJECT IDENTIFIER    

upsConfig-sixth 1.3.6.1.4.1.818.1.1.16.9
OBJECT IDENTIFIER    

upsGetSet-sixth 1.3.6.1.4.1.818.1.1.16.10
OBJECT IDENTIFIER    

geUPSTraps-sixth 1.3.6.1.4.1.818.1.1.16.11
OBJECT IDENTIFIER    

upsIdent-seventh 1.3.6.1.4.1.818.1.1.17.1
OBJECT IDENTIFIER    

upsBattery-seventh 1.3.6.1.4.1.818.1.1.17.2
OBJECT IDENTIFIER    

upsInput-seventh 1.3.6.1.4.1.818.1.1.17.3
OBJECT IDENTIFIER    

upsOutput-seventh 1.3.6.1.4.1.818.1.1.17.4
OBJECT IDENTIFIER    

upsBypass-seventh 1.3.6.1.4.1.818.1.1.17.5
OBJECT IDENTIFIER    

upsAlarm-seventh 1.3.6.1.4.1.818.1.1.17.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-seventh 1.3.6.1.4.1.818.1.1.17.6.3
OBJECT IDENTIFIER    

upsTest-seventh 1.3.6.1.4.1.818.1.1.17.7
OBJECT IDENTIFIER    

upsWellKnownTests-seventh 1.3.6.1.4.1.818.1.1.17.7.7
OBJECT IDENTIFIER    

upsControl-seventh 1.3.6.1.4.1.818.1.1.17.8
OBJECT IDENTIFIER    

upsConfig-seventh 1.3.6.1.4.1.818.1.1.17.9
OBJECT IDENTIFIER    

upsGetSet-seventh 1.3.6.1.4.1.818.1.1.17.10
OBJECT IDENTIFIER    

geUPSTraps-seventh 1.3.6.1.4.1.818.1.1.17.11
OBJECT IDENTIFIER    

upsIdent-eighth 1.3.6.1.4.1.818.1.1.18.1
OBJECT IDENTIFIER    

upsBattery-eighth 1.3.6.1.4.1.818.1.1.18.2
OBJECT IDENTIFIER    

upsInput-eighth 1.3.6.1.4.1.818.1.1.18.3
OBJECT IDENTIFIER    

upsOutput-eighth 1.3.6.1.4.1.818.1.1.18.4
OBJECT IDENTIFIER    

upsBypass-eighth 1.3.6.1.4.1.818.1.1.18.5
OBJECT IDENTIFIER    

upsAlarm-eighth 1.3.6.1.4.1.818.1.1.18.6
OBJECT IDENTIFIER    

upsWellKnownAlarms-eighth 1.3.6.1.4.1.818.1.1.18.6.3
OBJECT IDENTIFIER    

upsTest-eighth 1.3.6.1.4.1.818.1.1.18.7
OBJECT IDENTIFIER    

upsWellKnownTests-eighth 1.3.6.1.4.1.818.1.1.18.7.7
OBJECT IDENTIFIER    

upsControl-eighth 1.3.6.1.4.1.818.1.1.18.8
OBJECT IDENTIFIER    

upsConfig-eighth 1.3.6.1.4.1.818.1.1.18.9
OBJECT IDENTIFIER    

upsGetSet-eighth 1.3.6.1.4.1.818.1.1.18.10
OBJECT IDENTIFIER    

geUPSTraps-eighth 1.3.6.1.4.1.818.1.1.18.11
OBJECT IDENTIFIER    

geEnvironmental 1.3.6.1.4.1.818.1.2
OBJECT IDENTIFIER    

ioInterface-First 1.3.6.1.4.1.818.1.2.1
OBJECT IDENTIFIER    

ioInterface-Second 1.3.6.1.4.1.818.1.2.2
OBJECT IDENTIFIER    

ioInterface-Third 1.3.6.1.4.1.818.1.2.3
OBJECT IDENTIFIER    

ioInterface-Fourth 1.3.6.1.4.1.818.1.2.4
OBJECT IDENTIFIER    

ioInterface-Fifth 1.3.6.1.4.1.818.1.2.5
OBJECT IDENTIFIER    

ioInterface-Sixth 1.3.6.1.4.1.818.1.2.6
OBJECT IDENTIFIER    

ioInterface-Seventh 1.3.6.1.4.1.818.1.2.7
OBJECT IDENTIFIER    

ioInterface-Eighth 1.3.6.1.4.1.818.1.2.8
OBJECT IDENTIFIER    

ioInterfaceInputLine-First 1.3.6.1.4.1.818.1.2.1.1
OBJECT IDENTIFIER    

ioInterfaceOutputLine-First 1.3.6.1.4.1.818.1.2.1.2
OBJECT IDENTIFIER    

ioInterfaceAnalogueLine-First 1.3.6.1.4.1.818.1.2.1.3
OBJECT IDENTIFIER    

ioInterfaceTraps-First 1.3.6.1.4.1.818.1.2.1.4
OBJECT IDENTIFIER    

ioInterfaceInputLine-Second 1.3.6.1.4.1.818.1.2.2.1
OBJECT IDENTIFIER    

ioInterfaceOutputLine-Second 1.3.6.1.4.1.818.1.2.2.2
OBJECT IDENTIFIER    

ioInterfaceAnalogueLine-Second 1.3.6.1.4.1.818.1.2.2.3
OBJECT IDENTIFIER    

ioInterfaceTraps-Second 1.3.6.1.4.1.818.1.2.2.4
OBJECT IDENTIFIER    

ioInterfaceInputLine-Third 1.3.6.1.4.1.818.1.2.3.1
OBJECT IDENTIFIER    

ioInterfaceOutputLine-Third 1.3.6.1.4.1.818.1.2.3.2
OBJECT IDENTIFIER    

ioInterfaceAnalogueLine-Third 1.3.6.1.4.1.818.1.2.3.3
OBJECT IDENTIFIER    

ioInterfaceTraps-Third 1.3.6.1.4.1.818.1.2.3.4
OBJECT IDENTIFIER    

ioInterfaceInputLine-Fourth 1.3.6.1.4.1.818.1.2.4.1
OBJECT IDENTIFIER    

ioInterfaceOutputLine-Fourth 1.3.6.1.4.1.818.1.2.4.2
OBJECT IDENTIFIER    

ioInterfaceAnalogueLine-Fourth 1.3.6.1.4.1.818.1.2.4.3
OBJECT IDENTIFIER    

ioInterfaceTraps-Fourth 1.3.6.1.4.1.818.1.2.4.4
OBJECT IDENTIFIER    

ioInterfaceInputLine-Fifth 1.3.6.1.4.1.818.1.2.5.1
OBJECT IDENTIFIER    

ioInterfaceOutputLine-Fifth 1.3.6.1.4.1.818.1.2.5.2
OBJECT IDENTIFIER    

ioInterfaceAnalogueLine-Fifth 1.3.6.1.4.1.818.1.2.5.3
OBJECT IDENTIFIER    

ioInterfaceTraps-Fifth 1.3.6.1.4.1.818.1.2.5.4
OBJECT IDENTIFIER    

ioInterfaceInputLine-Sixth 1.3.6.1.4.1.818.1.2.6.1
OBJECT IDENTIFIER    

ioInterfaceOutputLine-Sixth 1.3.6.1.4.1.818.1.2.6.2
OBJECT IDENTIFIER    

ioInterfaceAnalogueLine-Sixth 1.3.6.1.4.1.818.1.2.6.3
OBJECT IDENTIFIER    

ioInterfaceTraps-Sixth 1.3.6.1.4.1.818.1.2.6.4
OBJECT IDENTIFIER    

ioInterfaceInputLine-Seventh 1.3.6.1.4.1.818.1.2.7.1
OBJECT IDENTIFIER    

ioInterfaceOutputLine-Seventh 1.3.6.1.4.1.818.1.2.7.2
OBJECT IDENTIFIER    

ioInterfaceAnalogueLine-Seventh 1.3.6.1.4.1.818.1.2.7.3
OBJECT IDENTIFIER    

ioInterfaceTraps-Seventh 1.3.6.1.4.1.818.1.2.7.4
OBJECT IDENTIFIER    

ioInterfaceInputLine-Eighth 1.3.6.1.4.1.818.1.2.8.1
OBJECT IDENTIFIER    

ioInterfaceOutputLine-Eighth 1.3.6.1.4.1.818.1.2.8.2
OBJECT IDENTIFIER    

ioInterfaceAnalogueLine-Eighth 1.3.6.1.4.1.818.1.2.8.3
OBJECT IDENTIFIER    

ioInterfaceTraps-Eighth 1.3.6.1.4.1.818.1.2.8.4
OBJECT IDENTIFIER    

geModem 1.3.6.1.4.1.818.1.3
OBJECT IDENTIFIER    

geDevices 1.3.6.1.4.1.818.1.100
OBJECT IDENTIFIER    

geDevicesDescriptions 1.3.6.1.4.1.818.1.100.1
OBJECT IDENTIFIER    

advSNMPWebIntCard 1.3.6.1.4.1.818.1.100.1.1
OBJECT IDENTIFIER    

snmpPWebIntCard 1.3.6.1.4.1.818.1.100.1.2
OBJECT IDENTIFIER    

snmpWebIntBox 1.3.6.1.4.1.818.1.100.1.3
OBJECT IDENTIFIER    

snmpSWPFAgent 1.3.6.1.4.1.818.1.100.1.4
OBJECT IDENTIFIER    

snmpSWJUMPAgent 1.3.6.1.4.1.818.1.100.1.5
OBJECT IDENTIFIER    

geClient 1.3.6.1.4.1.818.2.1
OBJECT IDENTIFIER    

geAgentConfig 1.3.6.1.4.1.818.3.1
OBJECT IDENTIFIER    

geAgentTraps 1.3.6.1.4.1.818.3.2
OBJECT IDENTIFIER    

geDiscoveredUPSsMask 1.3.6.1.4.1.818.1.1.1
Reading this variable returns bit mask indicating which UPSs in a parallel system are alive. Management software should poll only these UPSs on their snmp branches 11-18 as follows: 1 FirstUPS alive 2 SecondUPS alive 4 ThirdUPS alive 8 FourthUPS alive 16 FifthUPS alive 32 SixthUPS alive 64 SeventhUPS alive 128 EigthUPS alive Since the management software should always monitor the GenericUPS branch (10), this value has no meaning for single upses (which provide values on that snmp branch), and should be set to zero in that case.
OBJECT-TYPE    
  Integer32  

geRequestPacket 1.3.6.1.4.1.818.1.1.2
Put the string, formatted as a IMV/CP4 packet, directly to internally RS485 bus. This OID could be used for accede directly to the internally RS485 bus from a remote place.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geReplyPacket 1.3.6.1.4.1.818.1.1.3
Contain the reply of the IMV/CP4 request packet sent using the OID geRequestPacket. Every time that a write command has be made at the OID ge RequestPacket, the value of this OID is erased.
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentManufacturer-gen 1.3.6.1.4.1.818.1.1.10.1.1
The name of the UPS manufacturer.(*)
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsIdentModel-gen 1.3.6.1.4.1.818.1.1.10.1.2
The UPS Model designation.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentUPSSoftwareVersion-gen 1.3.6.1.4.1.818.1.1.10.1.3
The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentAgentSoftwareVersion-gen 1.3.6.1.4.1.818.1.1.10.1.4
The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentName-gen 1.3.6.1.4.1.818.1.1.10.1.5
A string identifying the UPS. This object should be set by the administrator.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentAttachedDevices-gen 1.3.6.1.4.1.818.1.1.10.1.6
A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentUPSSerialNumber-gen 1.3.6.1.4.1.818.1.1.10.1.7
The UPS serial number
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsIdentComProtVersion-gen 1.3.6.1.4.1.818.1.1.10.1.8
The IMV communication protocol version
OBJECT-TYPE    
  DisplayString Size(0..15)  

upsIdentOperatingTime-gen 1.3.6.1.4.1.818.1.1.10.1.9
The present value of the operating time. total 'on' time since UPS manufactured
OBJECT-TYPE    
  NonNegativeInteger32  

upsBatteryStatus-gen 1.3.6.1.4.1.818.1.1.10.2.1
The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
OBJECT-TYPE    
  Integer32 unknown(1), batteryNormal(2), batteryLow(3), batteryDepleted(4)  

upsSecondsOnBattery-gen 1.3.6.1.4.1.818.1.1.10.2.2
If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsEstimatedMinutesRemaining-gen 1.3.6.1.4.1.818.1.1.10.2.3
An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
OBJECT-TYPE    
  PositiveInteger32  

upsEstimatedChargeRemaining-gen 1.3.6.1.4.1.818.1.1.10.2.4
An estimate of the battery charge remaining expressed as a percent of full charge.(*)
OBJECT-TYPE    
  Integer32 0..100  

upsBatteryVoltage-gen 1.3.6.1.4.1.818.1.1.10.2.5
The magnitude of the present battery voltage.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsBatteryCurrent-gen 1.3.6.1.4.1.818.1.1.10.2.6
The present battery current.(*)
OBJECT-TYPE    
  Integer32  

upsBatteryTemperature-gen 1.3.6.1.4.1.818.1.1.10.2.7
The ambient temperature at or near the UPS Battery casing.(*)
OBJECT-TYPE    
  Integer32  

upsInputLineBads-gen 1.3.6.1.4.1.818.1.1.10.3.1
A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
OBJECT-TYPE    
  Counter32  

upsInputNumLines-gen 1.3.6.1.4.1.818.1.1.10.3.2
The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputTable-gen 1.3.6.1.4.1.818.1.1.10.3.3
A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
OBJECT-TYPE    
  SEQUENCE OF  
    UpsInputEntry-gen

upsInputEntry-gen 1.3.6.1.4.1.818.1.1.10.3.3.1
An entry containing information applicable to a particular input line.(*)
OBJECT-TYPE    
  UpsInputEntry-gen  

upsInputLineIndex-gen 1.3.6.1.4.1.818.1.1.10.3.3.1.1
The input line identifier.(*)
OBJECT-TYPE    
  PositiveInteger32  

upsInputFrequency-gen 1.3.6.1.4.1.818.1.1.10.3.3.1.2
The present input frequency.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputVoltage-gen 1.3.6.1.4.1.818.1.1.10.3.3.1.3
The magnitude of the present input voltage.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputCurrent-gen 1.3.6.1.4.1.818.1.1.10.3.3.1.4
The magnitude of the present input current.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputTruePower-gen 1.3.6.1.4.1.818.1.1.10.3.3.1.5
The magnitude of the present input true power.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputVoltageMin-gen 1.3.6.1.4.1.818.1.1.10.3.3.1.6
The lowest magnitude of the input voltage since last read out.
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputVoltageMax-gen 1.3.6.1.4.1.818.1.1.10.3.3.1.7
The highest magnitude of the input voltage since last read out.
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputSource-gen 1.3.6.1.4.1.818.1.1.10.4.1
The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
OBJECT-TYPE    
  Integer32 other(1), none(2), normal(3), bypass(4), battery(5), booster(6), reducer(7)  

upsOutputFrequency-gen 1.3.6.1.4.1.818.1.1.10.4.2
The present output frequency.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputNumLines-gen 1.3.6.1.4.1.818.1.1.10.4.3
The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputTable-gen 1.3.6.1.4.1.818.1.1.10.4.4
A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
OBJECT-TYPE    
  SEQUENCE OF  
    UpsOutputEntry-gen

upsOutputEntry-gen 1.3.6.1.4.1.818.1.1.10.4.4.1
An entry containing information applicable to a particular output line.(*)
OBJECT-TYPE    
  UpsOutputEntry-gen  

upsOutputLineIndex-gen 1.3.6.1.4.1.818.1.1.10.4.4.1.1
The output line identifier.(*)
OBJECT-TYPE    
  PositiveInteger32  

upsOutputVoltage-gen 1.3.6.1.4.1.818.1.1.10.4.4.1.2
The present output voltage.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputCurrent-gen 1.3.6.1.4.1.818.1.1.10.4.4.1.3
The present output current.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputPower-gen 1.3.6.1.4.1.818.1.1.10.4.4.1.4
The present output true power.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputPercentLoad-gen 1.3.6.1.4.1.818.1.1.10.4.4.1.5
The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
OBJECT-TYPE    
  Integer32 0..200  

upsBypassFrequency-gen 1.3.6.1.4.1.818.1.1.10.5.1
The present bypass frequency.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsBypassNumLines-gen 1.3.6.1.4.1.818.1.1.10.5.2
The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsBypassTable-gen 1.3.6.1.4.1.818.1.1.10.5.3
A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
OBJECT-TYPE    
  SEQUENCE OF  
    UpsBypassEntry-gen

upsBypassEntry-gen 1.3.6.1.4.1.818.1.1.10.5.3.1
An entry containing information applicable to a particular bypass input.(*)
OBJECT-TYPE    
  UpsBypassEntry-gen  

upsBypassLineIndex-gen 1.3.6.1.4.1.818.1.1.10.5.3.1.1
The bypass line identifier.(*)
OBJECT-TYPE    
  PositiveInteger32  

upsBypassVoltage-gen 1.3.6.1.4.1.818.1.1.10.5.3.1.2
The present bypass voltage.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsBypassCurrent-gen 1.3.6.1.4.1.818.1.1.10.5.3.1.3
The present bypass current.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsBypassPower-gen 1.3.6.1.4.1.818.1.1.10.5.3.1.4
The present true power conveyed by the bypass.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsAlarmsPresent-gen 1.3.6.1.4.1.818.1.1.10.6.1
The present number of active alarm conditions.(*)
OBJECT-TYPE    
  Gauge32  

upsAlarmTable-gen 1.3.6.1.4.1.818.1.1.10.6.2
A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
OBJECT-TYPE    
  SEQUENCE OF  
    UpsAlarmEntry-gen

upsAlarmEntry-gen 1.3.6.1.4.1.818.1.1.10.6.2.1
An entry containing information applicable to a particular alarm.(*)
OBJECT-TYPE    
  UpsAlarmEntry-gen  

upsAlarmId-gen 1.3.6.1.4.1.818.1.1.10.6.2.1.1
A unique identifier for an alarm condition. This value must remain constant.(*)
OBJECT-TYPE    
  PositiveInteger32  

upsAlarmDescr-gen 1.3.6.1.4.1.818.1.1.10.6.2.1.2
A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
OBJECT-TYPE    
  AutonomousType  

upsAlarmTime-gen 1.3.6.1.4.1.818.1.1.10.6.2.1.3
The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
OBJECT-TYPE    
  TimeStamp  

upsAlarmBatteryBad-gen 1.3.6.1.4.1.818.1.1.10.6.3.1
One or more batteries have been determined to require replacement.(*)
OBJECT-IDENTITY    

upsAlarmOnBattery-gen 1.3.6.1.4.1.818.1.1.10.6.3.2
The UPS is drawing power from the batteries.(*)
OBJECT-IDENTITY    

upsAlarmLowBattery-gen 1.3.6.1.4.1.818.1.1.10.6.3.3
The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
OBJECT-IDENTITY    

upsAlarmDepletedBattery-gen 1.3.6.1.4.1.818.1.1.10.6.3.4
The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
OBJECT-IDENTITY    

upsAlarmTempBad-gen 1.3.6.1.4.1.818.1.1.10.6.3.5
A temperature is out of tolerance.(*)
OBJECT-IDENTITY    

upsAlarmInputBad-gen 1.3.6.1.4.1.818.1.1.10.6.3.6
An input condition is out of tolerance.(*)
OBJECT-IDENTITY    

upsAlarmOutputBad-gen 1.3.6.1.4.1.818.1.1.10.6.3.7
An output condition (other than OutputOverload) is out of tolerance.(*)
OBJECT-IDENTITY    

upsAlarmOutputOverload-gen 1.3.6.1.4.1.818.1.1.10.6.3.8
The output load exceeds the UPS output capacity.(*)
OBJECT-IDENTITY    

upsAlarmOnBypass-gen 1.3.6.1.4.1.818.1.1.10.6.3.9
The Bypass is presently engaged on the UPS.(*)
OBJECT-IDENTITY    

upsAlarmBypassBad-gen 1.3.6.1.4.1.818.1.1.10.6.3.10
The Bypass is out of tolerance.(*)
OBJECT-IDENTITY    

upsAlarmOutputOffAsRequested-gen 1.3.6.1.4.1.818.1.1.10.6.3.11
The UPS has shutdown as requested, i.e., the output is off.(*)
OBJECT-IDENTITY    

upsAlarmUpsOffAsRequested-gen 1.3.6.1.4.1.818.1.1.10.6.3.12
The entire UPS has shutdown as commanded.(*)
OBJECT-IDENTITY    

upsAlarmChargerFailed-gen 1.3.6.1.4.1.818.1.1.10.6.3.13
An uncorrected problem has been detected within the UPS charger subsystem.(*)
OBJECT-IDENTITY    

upsAlarmUpsOutputOff-gen 1.3.6.1.4.1.818.1.1.10.6.3.14
The output of the UPS is in the off state.(*)
OBJECT-IDENTITY    

upsAlarmUpsSystemOff-gen 1.3.6.1.4.1.818.1.1.10.6.3.15
The UPS system is in the off state.(*)
OBJECT-IDENTITY    

upsAlarmFanFailure-gen 1.3.6.1.4.1.818.1.1.10.6.3.16
The failure of one or more fans in the UPS has been detected.(*)
OBJECT-IDENTITY    

upsAlarmFuseFailure-gen 1.3.6.1.4.1.818.1.1.10.6.3.17
The failure of one or more fuses has been detected.(*)
OBJECT-IDENTITY    

upsAlarmGeneralFault-gen 1.3.6.1.4.1.818.1.1.10.6.3.18
A general fault in the UPS has been detected.(*)
OBJECT-IDENTITY    

upsAlarmDiagnosticTestFailed-gen 1.3.6.1.4.1.818.1.1.10.6.3.19
The result of the last diagnostic test indicates a failure.(*)
OBJECT-IDENTITY    

upsAlarmCommunicationsLost-gen 1.3.6.1.4.1.818.1.1.10.6.3.20
A problem has been encountered in the communications between the agent and the UPS.(*)
OBJECT-IDENTITY    

upsAlarmAwaitingPower-gen 1.3.6.1.4.1.818.1.1.10.6.3.21
The UPS output is off and the UPS is awaiting the return of input power.(*)
OBJECT-IDENTITY    

upsAlarmShutdownPending-gen 1.3.6.1.4.1.818.1.1.10.6.3.22
A upsShutdownAfterDelay countdown is underway.(*)
OBJECT-IDENTITY    

upsAlarmShutdownImminent-gen 1.3.6.1.4.1.818.1.1.10.6.3.23
The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
OBJECT-IDENTITY    

upsAlarmTestInProgress-gen 1.3.6.1.4.1.818.1.1.10.6.3.24
A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
OBJECT-IDENTITY    

upsAlarmReceptacleOff-gen 1.3.6.1.4.1.818.1.1.10.6.3.25
The receptacle are switch off
OBJECT-IDENTITY    

upsAlarmMaskA-gen 1.3.6.1.4.1.818.1.1.10.6.4
Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
OBJECT-TYPE    
  NonNegativeInteger32  

upsTestId-gen 1.3.6.1.4.1.818.1.1.10.7.1
The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
OBJECT-TYPE    
  OBJECT IDENTIFIER  

upsTestSpinLock-gen 1.3.6.1.4.1.818.1.1.10.7.2
A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto try-again } if (error-index == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lock-value + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)
OBJECT-TYPE    
  TestAndIncr  

upsTestResultsSummary-gen 1.3.6.1.4.1.818.1.1.10.7.3
The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
OBJECT-TYPE    
  Integer32 donePass(1), doneWarning(2), doneError(3), aborted(4), inProgress(5), noTestsInitiated(6)  

upsTestResultsDetail-gen 1.3.6.1.4.1.818.1.1.10.7.4
Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
OBJECT-TYPE    
  DisplayString Size(0..255)  

upsTestStartTime-gen 1.3.6.1.4.1.818.1.1.10.7.5
The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
OBJECT-TYPE    
  TimeStamp  

upsTestElapsedTime-gen 1.3.6.1.4.1.818.1.1.10.7.6
The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
OBJECT-TYPE    
  TimeInterval  

upsTestNoTestsInitiated-gen 1.3.6.1.4.1.818.1.1.10.7.7.1
No tests have been initiated and no test is in progress.(*)
OBJECT-IDENTITY    

upsTestAbortTestInProgress-gen 1.3.6.1.4.1.818.1.1.10.7.7.2
The test in progress is to be aborted / the test in progress was aborted.(*)
OBJECT-IDENTITY    

upsTestGeneralSystemsTest-gen 1.3.6.1.4.1.818.1.1.10.7.7.3
The manufacturer's standard test of UPS device systems.(*)
OBJECT-IDENTITY    

upsTestQuickBatteryTest-gen 1.3.6.1.4.1.818.1.1.10.7.7.4
A test that is sufficient to determine if the battery needs replacement.(*)
OBJECT-IDENTITY    

upsTestDeepBatteryCalibration-gen 1.3.6.1.4.1.818.1.1.10.7.7.5
The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
OBJECT-IDENTITY    

upsShutdownType-gen 1.3.6.1.4.1.818.1.1.10.8.1
This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
OBJECT-TYPE    
  Integer32 output(1), system(2)  

upsShutdownAfterDelay-gen 1.3.6.1.4.1.818.1.1.10.8.2
Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
OBJECT-TYPE    
  Integer32 -1..2147483648  

upsStartupAfterDelay-gen 1.3.6.1.4.1.818.1.1.10.8.3
Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
OBJECT-TYPE    
  Integer32 -1..2147483648  

upsRebootWithDuration-gen 1.3.6.1.4.1.818.1.1.10.8.4
Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
OBJECT-TYPE    
  Integer32 -1..300  

upsAutoRestart-gen 1.3.6.1.4.1.818.1.1.10.8.5
Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
OBJECT-TYPE    
  Integer32 on(1), off(2)  

upsReceptaclesNum-gen 1.3.6.1.4.1.818.1.1.10.8.6
The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
OBJECT-TYPE    
  NonNegativeInteger32  

upsReceptacleTable-gen 1.3.6.1.4.1.818.1.1.10.8.7
A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
OBJECT-TYPE    
  SEQUENCE OF  
    UpsReceptacleEntry-gen

upsReceptacleEntry-gen 1.3.6.1.4.1.818.1.1.10.8.7.1
An entry containing information applicable to a particular receptacle.
OBJECT-TYPE    
  UpsReceptacleEntry-gen  

upsReceptacleLineIndex-gen 1.3.6.1.4.1.818.1.1.10.8.7.1.1
The receptacle line identifier.
OBJECT-TYPE    
  PositiveInteger32  

upsReceptacleOnOff-gen 1.3.6.1.4.1.818.1.1.10.8.7.1.2
The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
OBJECT-TYPE    
  Integer32 on(1), off(2)  

upsUPSMode-gen 1.3.6.1.4.1.818.1.1.10.8.8
The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
OBJECT-TYPE    
  Integer32 off-line(1), on-line(2), ecomode(3)  

upsRectifierOnOff-gen 1.3.6.1.4.1.818.1.1.10.8.9
The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
OBJECT-TYPE    
  Integer32 on(1), off(2)  

upsBatteryChargeMethod-gen 1.3.6.1.4.1.818.1.1.10.8.10
The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
OBJECT-TYPE    
  Integer32 normal-charge(1), boost-charge(2)  

upsInverterOnOff-gen 1.3.6.1.4.1.818.1.1.10.8.11
The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
OBJECT-TYPE    
  Integer32 on(1), off(2)  

upsBypassOnOff-gen 1.3.6.1.4.1.818.1.1.10.8.12
The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
OBJECT-TYPE    
  Integer32 on(1), off(2)  

upsLoadSource-gen 1.3.6.1.4.1.818.1.1.10.8.13
The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
OBJECT-TYPE    
  Integer32 on-bypass(1), on-Inverter(2), on-Detour(3), load-Off(4), other(5)  

upsConfigInputVoltage-gen 1.3.6.1.4.1.818.1.1.10.9.1
The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigInputFreq-gen 1.3.6.1.4.1.818.1.1.10.9.2
The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigOutputVoltage-gen 1.3.6.1.4.1.818.1.1.10.9.3
The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigOutputFreq-gen 1.3.6.1.4.1.818.1.1.10.9.4
The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigOutputVA-gen 1.3.6.1.4.1.818.1.1.10.9.5
The magnitude of the nominal Volt-Amp rating.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigOutputPower-gen 1.3.6.1.4.1.818.1.1.10.9.6
The magnitude of the nominal true power rating.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigLowBattTime-gen 1.3.6.1.4.1.818.1.1.10.9.7
The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigAudibleStatus-gen 1.3.6.1.4.1.818.1.1.10.9.8
The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
OBJECT-TYPE    
  Integer32 disabled(1), enabled(2), muted(3)  

upsConfigLowVoltageTransferPoint-gen 1.3.6.1.4.1.818.1.1.10.9.9
The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigHighVoltageTransferPoint-gen 1.3.6.1.4.1.818.1.1.10.9.10
The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigBatteryCapacity-gen 1.3.6.1.4.1.818.1.1.10.9.11
The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigBatteryChargeCurrent-gen 1.3.6.1.4.1.818.1.1.10.9.12
The maximum battery charge current, including external chargers.
OBJECT-TYPE    
  NonNegativeInteger32  

upsConfigNoLoadShutdown-gen 1.3.6.1.4.1.818.1.1.10.9.13
Dis- or enable 'no load' shutdown from the contact interface.
OBJECT-TYPE    
  Integer32 disabled(1), enabled(2)  

upsConfigStartDelay-gen 1.3.6.1.4.1.818.1.1.10.9.14
Minimum required autonomy time before the UPS may perform an autorestart.
OBJECT-TYPE    
  PositiveInteger32  

upsEventGetNext-gen 1.3.6.1.4.1.818.1.1.10.10.1
The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
OBJECT-TYPE    
  PositiveInteger32 1..10  

upsEventGetPrevious-gen 1.3.6.1.4.1.818.1.1.10.10.2
The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
OBJECT-TYPE    
  PositiveInteger32 1..10  

upsEventSetStartingTimeStamp-gen 1.3.6.1.4.1.818.1.1.10.10.3
The timestamp which is used as starting point for downloading events from the UPS event buffer
OBJECT-TYPE    
  NonNegativeInteger32  

upsEventRetreiveCurrentTimeStamp-gen 1.3.6.1.4.1.818.1.1.10.10.4
The current timestamp is retreived from the UPS
OBJECT-TYPE    
  NonNegativeInteger32  

upsEventTableSize-gen 1.3.6.1.4.1.818.1.1.10.10.5
The number of entries in the event table. This object indicates the number of rows in the event table.
OBJECT-TYPE    
  NonNegativeInteger32  

upsEventTable-gen 1.3.6.1.4.1.818.1.1.10.10.6
A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp
OBJECT-TYPE    
  SEQUENCE OF  
    UpsEventEntry-gen

upsEventEntry-gen 1.3.6.1.4.1.818.1.1.10.10.6.1
An entry containing information applicable to a particular event.
OBJECT-TYPE    
  UpsEventEntry-gen  

upsEventLineIndex-gen 1.3.6.1.4.1.818.1.1.10.10.6.1.1
The event line identifier.
OBJECT-TYPE    
  PositiveInteger32  

upsEventCode-gen 1.3.6.1.4.1.818.1.1.10.10.6.1.2
The event code in numerical format.
OBJECT-TYPE    
  NonNegativeInteger32  

upsEventStatus-gen 1.3.6.1.4.1.818.1.1.10.10.6.1.3
The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
OBJECT-TYPE    
  NonNegativeInteger32  

upsEventTime-gen 1.3.6.1.4.1.818.1.1.10.10.6.1.4
The timestamp of the moment the event was generated.
OBJECT-TYPE    
  NonNegativeInteger32  

upsParametersRead-gen 1.3.6.1.4.1.818.1.1.10.10.7
The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
OBJECT-TYPE    
  PositiveInteger32 1..16  

upsParametersWrite-gen 1.3.6.1.4.1.818.1.1.10.10.8
The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
OBJECT-TYPE    
  PositiveInteger32 1..16  

upsParametersStartAddress-gen 1.3.6.1.4.1.818.1.1.10.10.9
The address which is used as starting point for downloading parameters from the UPS
OBJECT-TYPE    
  NonNegativeInteger32  

upsParameterTableSize-gen 1.3.6.1.4.1.818.1.1.10.10.10
The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
OBJECT-TYPE    
  NonNegativeInteger32  

upsParameterTable-gen 1.3.6.1.4.1.818.1.1.10.10.11
A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
OBJECT-TYPE    
  SEQUENCE OF  
    UpsParameterEntry-gen

upsParameterEntry-gen 1.3.6.1.4.1.818.1.1.10.10.11.1
An entry containing information applicable to a particular parameter.
OBJECT-TYPE    
  UpsParameterEntry-gen  

upsParameterLineIndex-gen 1.3.6.1.4.1.818.1.1.10.10.11.1.1
The parameter line identifier.
OBJECT-TYPE    
  PositiveInteger32  

upsParameterValue-gen 1.3.6.1.4.1.818.1.1.10.10.11.1.2
The parameter value in numerical format.
OBJECT-TYPE    
  Integer32  

upsStatus-gen 1.3.6.1.4.1.818.1.1.10.10.12
The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
OBJECT-TYPE    
  NonNegativeInteger32  

upsMainsStatisticsMBfail-gen 1.3.6.1.4.1.818.1.1.10.10.13
Count of main bypass failures (>200 ms), since UPS installation.
OBJECT-TYPE    
  NonNegativeInteger32  

upsMainsStatisticsMRfail-gen 1.3.6.1.4.1.818.1.1.10.10.14
Count of mains rectifier failures (>200 ms), since UPS installation.
OBJECT-TYPE    
  NonNegativeInteger32  

upsMainsStatisticsB2-gen 1.3.6.1.4.1.818.1.1.10.10.15
Count of transients on the mains bypass (0..2 ms), during the last 7 days.
OBJECT-TYPE    
  NonNegativeInteger32  

upsMainsStatisticsB5-gen 1.3.6.1.4.1.818.1.1.10.10.16
Count of transients on the mains bypass (2..5 ms), during the last 7 days.
OBJECT-TYPE    
  NonNegativeInteger32  

upsMainsStatisticsB10-gen 1.3.6.1.4.1.818.1.1.10.10.17
Count of transients on the mains bypass (5..10 ms), during the last 7 days.
OBJECT-TYPE    
  NonNegativeInteger32  

upsMainsStatisticsB200-gen 1.3.6.1.4.1.818.1.1.10.10.18
Count of transients on the mains bypass (10..200 ms), during the last 7 days.
OBJECT-TYPE    
  NonNegativeInteger32  

upsMainsStatisticsBypRel-gen 1.3.6.1.4.1.818.1.1.10.10.19
Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
OBJECT-TYPE    
  NonNegativeInteger32  

upsTime-gen 1.3.6.1.4.1.818.1.1.10.10.20
The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-genERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
OBJECT-TYPE    
  NonNegativeInteger32  

upsRequestPermission-gen 1.3.6.1.4.1.818.1.1.10.10.21
An encrypted code is send to enable use of restricted write objects during a limited period of time.
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsEventGetCode-gen 1.3.6.1.4.1.818.1.1.10.10.22
The code which is used as starting point to downloading the events from the UPS event buffer.
OBJECT-TYPE    
  Integer32  

upsEventSpinLock-gen 1.3.6.1.4.1.818.1.1.10.10.23
A spin lock on the event subsystem.
OBJECT-TYPE    
  TestAndIncr  

upsParameterSpinLock-gen 1.3.6.1.4.1.818.1.1.10.10.24
A spin lock on the parameters subsystem.
OBJECT-TYPE    
  TestAndIncr  

upsAlarmBatteryBad-gen 1
One or more batteries have been determined to require replacement.
TRAP-TYPE    

upsAlarmOnBattery-gen 2
An On Battery condition is restored.
TRAP-TYPE    

upsAlarmLowBattery-gen 3
The remaining battery run-time is less than or equal to upsConfigLowBattTime.
TRAP-TYPE    

upsAlarmDepletedBattery-gen 4
The UPS will be unable to sustain the present load when and if the utility power is lost)
TRAP-TYPE    

upsAlarmTempBad-gen 5
A temperature is out of tolerance.
TRAP-TYPE    

upsAlarmInputBad-gen 6
An input condition is out of tolerance.
TRAP-TYPE    

upsAlarmOutputBad-gen 7
An output condition (other than OutputOverload) is out of tolerance.
TRAP-TYPE    

upsAlarmOutputOverload-gen 8
The output load exceeds the UPS output capacity.
TRAP-TYPE    

upsAlarmOnBypass-gen 9
The Bypass is presently engaged on the UPS.
TRAP-TYPE    

upsAlarmBypassBad-gen 10
The Bypass is out of tolerance.
TRAP-TYPE    

upsAlarmOutputOffAsRequested-gen 11
The UPS has shutdown as requested, i.e., the output is off.
TRAP-TYPE    

upsAlarmUpsOffAsRequested-gen 12
The entire UPS has shutdown as commanded.
TRAP-TYPE    

upsAlarmChargerFailed-gen 13
An uncorrected problem has been detected within the UPS charger subsystem.
TRAP-TYPE    

upsAlarmUpsOutputOff-gen 14
The output of the UPS is in the off state.
TRAP-TYPE    

upsAlarmUpsSystemOff-gen 15
The UPS system is in the off state.
TRAP-TYPE    

upsAlarmFanFailure-gen 16
The failure of one or more fans in the UPS has been detected.
TRAP-TYPE    

upsAlarmFuseFailure-gen 17
The failure of one or more fuses has been detected.
TRAP-TYPE    

upsAlarmGeneralFault-gen 18
A general fault in the UPS has been detected.
TRAP-TYPE    

upsAlarmDiagnosticTestFailed-gen 19
The result of the last diagnostic test indicates a failure.
TRAP-TYPE    

upsAlarmCommunicationsLost-gen 20
A problem has been encountered in the communication between the agent and the UPS.
TRAP-TYPE    

upsAlarmAwaitingPower-gen 21
The UPS output is off and the UPS is awaiting the return of the input power (*).
TRAP-TYPE    

upsAlarmShutdownPending-gen 22
A upsShutdownAfterDelay countdown is underway.
TRAP-TYPE    

upsAlarmShutdownImminent-gen 23
The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
TRAP-TYPE    

upsAlarmTestInProgress-gen 24
A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
TRAP-TYPE    

upsAlarmReceptacleOff-gen 25
A receptacle has been switched off.
TRAP-TYPE    

upsAlarmBatteryBadRestored-gen 33
A Battery bad condition is restored.
TRAP-TYPE    

upsAlarmOnBatteryRestored-gen 34
The UPS is drawing power from mains again.
TRAP-TYPE    

upsAlarmLowBatteryRestored-gen 35
A Low Battery condition is restored.
TRAP-TYPE    

upsAlarmDepletedBatteryRestored-gen 36
A Depleted Battery condition is restored.
TRAP-TYPE    

upsAlarmTempBadRestored-gen 37
A bad temperature condition is restored.
TRAP-TYPE    

upsAlarmInputBadRestored-gen 38
An input bad condition is restored.
TRAP-TYPE    

upsAlarmOutputBadRestored-gen 39
An output bad condition is restored.
TRAP-TYPE    

upsAlarmOutputOverloadRestored-gen 40
An output overload condition is restored.
TRAP-TYPE    

upsAlarmOnBypassRestored-gen 41
An On Bypass condition is restored.
TRAP-TYPE    

upsAlarmBypassBadRestored-gen 42
A Bypass bad condition is restored.
TRAP-TYPE    

upsAlarmOutputOffAsRequestedRestored-gen 43
A request shutdown has been restored.
TRAP-TYPE    

upsAlarmUpsOffAsRequestedRestored-gen 44
A entire UPS command has been restored.
TRAP-TYPE    

upsAlarmChargerFailedRestored-gen 45
A Charger Failer condition is restored.
TRAP-TYPE    

upsAlarmUpsOutputOn-gen 46
The output of the UPS switched in the on state.
TRAP-TYPE    

upsAlarmUpsSystemOn-gen 47
The UPS system is switched in the on state.
TRAP-TYPE    

upsAlarmFanFailureRestored-gen 48
A Fan failure condition is restored.
TRAP-TYPE    

upsAlarmFuseFailureRestored-gen 49
A Fuse failure condition is restored.
TRAP-TYPE    

upsAlarmGeneralFaultRestored-gen 50
A general fault is restored.
TRAP-TYPE    

upsAlarmDiagnosticTestFailedRestored-gen 51
A last diagnostic test indicates a failure is restored.
TRAP-TYPE    

upsAlarmCommunicationsLostRestored-gen 52
A problem in the communication between the agent and the UPS is restored.
TRAP-TYPE    

upsAlarmAwaitingPowerRestored-gen 53
A awaiting power condition is restored (*).
TRAP-TYPE    

upsAlarmShutdownPendingRestored-gen 54
A upsShutdownAfterDelay countdown is restored.
TRAP-TYPE    

upsAlarmShutdownImminentRestored-gen 55
A shutdown imminent condition is restored.
TRAP-TYPE    

upsAlarmTestInProgressRestored-gen 56
The test is in progress is terminated.
TRAP-TYPE    

upsAlarmReceptacleOn 57
A receptacle has been switched on.
TRAP-TYPE    

upsAlarmValueLow-gen 129
A measurement value reached a value below its low-level threshold.
TRAP-TYPE    

upsAlarmValueHigh-gen 130
A measurement value reached a value higher than its high-level threshold.
TRAP-TYPE    

upsAlarmValueLowRestored-gen 133
A ValueLow alarm condition is restored.
TRAP-TYPE    

upsAlarmValueHighRestored-gen 134
A ValueHigh alarm condition is restored.
TRAP-TYPE    

ioInterfaceNumInputs-First 1.3.6.1.4.1.818.1.2.1.1.1
The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceInputTable-First 1.3.6.1.4.1.818.1.2.1.1.2
A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceInputEntry-First

ioInterfaceInputEntry-First 1.3.6.1.4.1.818.1.2.1.1.2.1
An entry containing information applicable to a particular input line.
OBJECT-TYPE    
  IoInterfaceInputEntry-First  

ioInterfaceInputLineIndex-First 1.3.6.1.4.1.818.1.2.1.1.2.1.1
The input line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceInputDescription-First 1.3.6.1.4.1.818.1.2.1.1.2.1.2
A description of the alarm monitored by this input line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceInputStatus-First 1.3.6.1.4.1.818.1.2.1.1.2.1.3
The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceEdgeMode-First 1.3.6.1.4.1.818.1.2.1.1.2.1.4
Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

ioInterfaceAlarmMask-First 1.3.6.1.4.1.818.1.2.1.1.2.1.5
Alarm functionality for the input line can be set active or inactive.
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceAlarmDelay-First 1.3.6.1.4.1.818.1.2.1.1.3
Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceNumOutput-First 1.3.6.1.4.1.818.1.2.1.2.1
The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceOutputTable-First 1.3.6.1.4.1.818.1.2.1.2.2
A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceOutputEntry-First

ioInterfaceOutputEntry-First 1.3.6.1.4.1.818.1.2.1.2.2.1
An entry containing information applicable to a particular output line.
OBJECT-TYPE    
  IoInterfaceOutputEntry-First  

ioInterfaceOutputLineIndex-First 1.3.6.1.4.1.818.1.2.1.2.2.1.1
The output line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceOutputDescription-First 1.3.6.1.4.1.818.1.2.1.2.2.1.2
A description of the alarm monitored by this output line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceOutputStatus-First 1.3.6.1.4.1.818.1.2.1.2.2.1.3
The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceNumAnalogue-First 1.3.6.1.4.1.818.1.2.1.3.1
The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceAnalogueTable-First 1.3.6.1.4.1.818.1.2.1.3.2
A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceAnalogueEntry-First

ioInterfaceAnalogueEntry-First 1.3.6.1.4.1.818.1.2.1.3.2.1
An entry containing information applicable to a particular analogue line.
OBJECT-TYPE    
  IoInterfaceAnalogueEntry-First  

ioInterfaceAnalogueLineIndex-First 1.3.6.1.4.1.818.1.2.1.3.2.1.1
The analogue line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceAnalogueDescription-First 1.3.6.1.4.1.818.1.2.1.3.2.1.2
A description of the alarm monitored by this analogue line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceAnalogueStatus-First 1.3.6.1.4.1.818.1.2.1.3.2.1.3
Read analogue value 1, when the board support such functionality
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueLowThreshold-First 1.3.6.1.4.1.818.1.2.1.3.2.1.4
Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueHighThreshold-First 1.3.6.1.4.1.818.1.2.1.3.2.1.5
High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetLowThreshold-First 1.3.6.1.4.1.818.1.2.1.3.2.1.6
After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetHighThreshold-First 1.3.6.1.4.1.818.1.2.1.3.2.1.7
After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioAlarmGenericChange-First 1
An generic change of a digital input/digital output/analog input has become active.
TRAP-TYPE    

ioInterfaceNumInputs-Second 1.3.6.1.4.1.818.1.2.2.1.1
The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceInputTable-Second 1.3.6.1.4.1.818.1.2.2.1.2
A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceInputEntry-Second

ioInterfaceInputEntry-Second 1.3.6.1.4.1.818.1.2.2.1.2.1
An entry containing information applicable to a particular input line.
OBJECT-TYPE    
  IoInterfaceInputEntry-Second  

ioInterfaceInputLineIndex-Second 1.3.6.1.4.1.818.1.2.2.1.2.1.1
The input line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceInputDescription-Second 1.3.6.1.4.1.818.1.2.2.1.2.1.2
A description of the alarm monitored by this input line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceInputStatus-Second 1.3.6.1.4.1.818.1.2.2.1.2.1.3
The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceEdgeMode-Second 1.3.6.1.4.1.818.1.2.2.1.2.1.4
Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

ioInterfaceAlarmMask-Second 1.3.6.1.4.1.818.1.2.2.1.2.1.5
Alarm functionality for the input line can be set active or inactive.
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceAlarmDelay-Second 1.3.6.1.4.1.818.1.2.2.1.2.1.6
Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceNumOutput-Second 1.3.6.1.4.1.818.1.2.2.2.1
The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceOutputTable-Second 1.3.6.1.4.1.818.1.2.2.2.2
A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceOutputEntry-Second

ioInterfaceOutputEntry-Second 1.3.6.1.4.1.818.1.2.2.2.2.1
An entry containing information applicable to a particular output line.
OBJECT-TYPE    
  IoInterfaceOutputEntry-Second  

ioInterfaceOutputLineIndex-Second 1.3.6.1.4.1.818.1.2.2.2.2.1.1
The output line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceOutputDescription-Second 1.3.6.1.4.1.818.1.2.2.2.2.1.2
A description of the alarm monitored by this output line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceOutputStatus-Second 1.3.6.1.4.1.818.1.2.2.2.2.1.3
The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceNumAnalogue-Second 1.3.6.1.4.1.818.1.2.2.3.1
The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceAnalogueTable-Second 1.3.6.1.4.1.818.1.2.2.3.2
A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceAnalogueEntry-Second

ioInterfaceAnalogueEntry-Second 1.3.6.1.4.1.818.1.2.2.3.2.1
An entry containing information applicable to a particular analogue line.
OBJECT-TYPE    
  IoInterfaceAnalogueEntry-Second  

ioInterfaceAnalogueLineIndex-Second 1.3.6.1.4.1.818.1.2.2.3.2.1.1
The analogue line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceAnalogueDescription-Second 1.3.6.1.4.1.818.1.2.2.3.2.1.2
A description of the alarm monitored by this analogue line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceAnalogueStatus-Second 1.3.6.1.4.1.818.1.2.2.3.2.1.3
Read analogue value 1, when the board support such functionality
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueLowThreshold-Second 1.3.6.1.4.1.818.1.2.2.3.2.1.4
Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueHighThreshold-Second 1.3.6.1.4.1.818.1.2.2.3.2.1.5
High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetLowThreshold-Second 1.3.6.1.4.1.818.1.2.2.3.2.1.6
After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetHighThreshold-Second 1.3.6.1.4.1.818.1.2.2.3.2.1.7
After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioAlarmGenericChange-Second 1
An generic change of a digital input/digital output/analog input has become active.
TRAP-TYPE    

ioInterfaceNumInputs-Third 1.3.6.1.4.1.818.1.2.3.1.1
The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceInputTable-Third 1.3.6.1.4.1.818.1.2.3.1.2
A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceInputEntry-Third

ioInterfaceInputEntry-Third 1.3.6.1.4.1.818.1.2.3.1.2.1
An entry containing information applicable to a particular input line.
OBJECT-TYPE    
  IoInterfaceInputEntry-Third  

ioInterfaceInputLineIndex-Third 1.3.6.1.4.1.818.1.2.3.1.2.1.1
The input line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceInputDescription-Third 1.3.6.1.4.1.818.1.2.3.1.2.1.2
A description of the alarm monitored by this input line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceInputStatus-Third 1.3.6.1.4.1.818.1.2.3.1.2.1.3
The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceEdgeMode-Third 1.3.6.1.4.1.818.1.2.3.1.2.1.4
Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

ioInterfaceAlarmMask-Third 1.3.6.1.4.1.818.1.2.3.1.2.1.5
Alarm functionality for the input line can be set active or inactive.
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceAlarmDelay-Third 1.3.6.1.4.1.818.1.2.3.1.2.1.6
Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceNumOutput-Third 1.3.6.1.4.1.818.1.2.3.2.1
The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceOutputTable-Third 1.3.6.1.4.1.818.1.2.3.2.2
A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceOutputEntry-Third

ioInterfaceOutputEntry-Third 1.3.6.1.4.1.818.1.2.3.2.2.1
An entry containing information applicable to a particular output line.
OBJECT-TYPE    
  IoInterfaceOutputEntry-Third  

ioInterfaceOutputLineIndex-Third 1.3.6.1.4.1.818.1.2.3.2.2.1.1
The output line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceOutputDescription-Third 1.3.6.1.4.1.818.1.2.3.2.2.1.2
A description of the alarm monitored by this output line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceOutputStatus-Third 1.3.6.1.4.1.818.1.2.3.2.2.1.3
The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceNumAnalogue-Third 1.3.6.1.4.1.818.1.2.3.3.1
The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceAnalogueTable-Third 1.3.6.1.4.1.818.1.2.3.3.2
A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceAnalogueEntry-Third

ioInterfaceAnalogueEntry-Third 1.3.6.1.4.1.818.1.2.3.3.2.1
An entry containing information applicable to a particular analogue line.
OBJECT-TYPE    
  IoInterfaceAnalogueEntry-Third  

ioInterfaceAnalogueLineIndex-Third 1.3.6.1.4.1.818.1.2.3.3.2.1.1
The analogue line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceAnalogueDescription-Third 1.3.6.1.4.1.818.1.2.3.3.2.1.2
A description of the alarm monitored by this analogue line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceAnalogueStatus-Third 1.3.6.1.4.1.818.1.2.3.3.2.1.3
Read analogue value 1, when the board support such functionality
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueLowThreshold-Third 1.3.6.1.4.1.818.1.2.3.3.2.1.4
Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueHighThreshold-Third 1.3.6.1.4.1.818.1.2.3.3.2.1.5
High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetLowThreshold-Third 1.3.6.1.4.1.818.1.2.3.3.2.1.6
After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetHighThreshold-Third 1.3.6.1.4.1.818.1.2.3.3.2.1.7
After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioAlarmGenericChange-Third 1
An generic change of a digital input/digital output/analog input has become active.
TRAP-TYPE    

ioInterfaceNumInputs-Fourth 1.3.6.1.4.1.818.1.2.4.1.1
The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceInputTable-Fourth 1.3.6.1.4.1.818.1.2.4.1.2
A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceInputEntry-Fourth

ioInterfaceInputEntry-Fourth 1.3.6.1.4.1.818.1.2.4.1.2.1
An entry containing information applicable to a particular input line.
OBJECT-TYPE    
  IoInterfaceInputEntry-Fourth  

ioInterfaceInputLineIndex-Fourth 1.3.6.1.4.1.818.1.2.4.1.2.1.1
The input line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceInputDescription-Fourth 1.3.6.1.4.1.818.1.2.4.1.2.1.2
A description of the alarm monitored by this input line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceInputStatus-Fourth 1.3.6.1.4.1.818.1.2.4.1.2.1.3
The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceEdgeMode-Fourth 1.3.6.1.4.1.818.1.2.4.1.2.1.4
Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

ioInterfaceAlarmMask-Fourth 1.3.6.1.4.1.818.1.2.4.1.2.1.5
Alarm functionality for the input line can be set active or inactive.
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceAlarmDelay-Fourth 1.3.6.1.4.1.818.1.2.4.1.2.1.6
Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceNumOutput-Fourth 1.3.6.1.4.1.818.1.2.4.2.1
The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceOutputTable-Fourth 1.3.6.1.4.1.818.1.2.4.2.2
A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceOutputEntry-Fourth

ioInterfaceOutputEntry-Fourth 1.3.6.1.4.1.818.1.2.4.2.2.1
An entry containing information applicable to a particular output line.
OBJECT-TYPE    
  IoInterfaceOutputEntry-Fourth  

ioInterfaceOutputLineIndex-Fourth 1.3.6.1.4.1.818.1.2.4.2.2.1.1
The output line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceOutputDescription-Fourth 1.3.6.1.4.1.818.1.2.4.2.2.1.2
A description of the alarm monitored by this output line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceOutputStatus-Fourth 1.3.6.1.4.1.818.1.2.4.2.2.1.3
The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceNumAnalogue-Fourth 1.3.6.1.4.1.818.1.2.4.3.1
The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceAnalogueTable-Fourth 1.3.6.1.4.1.818.1.2.4.3.2
A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceAnalogueEntry-Fourth

ioInterfaceAnalogueEntry-Fourth 1.3.6.1.4.1.818.1.2.4.3.2.1
An entry containing information applicable to a particular analogue line.
OBJECT-TYPE    
  IoInterfaceAnalogueEntry-Fourth  

ioInterfaceAnalogueLineIndex-Fourth 1.3.6.1.4.1.818.1.2.4.3.2.1.1
The analogue line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceAnalogueDescription-Fourth 1.3.6.1.4.1.818.1.2.4.3.2.1.2
A description of the alarm monitored by this analogue line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceAnalogueStatus-Fourth 1.3.6.1.4.1.818.1.2.4.3.2.1.3
Read analogue value 1, when the board support such functionality
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueLowThreshold-Fourth 1.3.6.1.4.1.818.1.2.4.3.2.1.4
Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueHighThreshold-Fourth 1.3.6.1.4.1.818.1.2.4.3.2.1.5
High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetLowThreshold-Fourth 1.3.6.1.4.1.818.1.2.4.3.2.1.6
After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetHighThreshold-Fourth 1.3.6.1.4.1.818.1.2.4.3.2.1.7
After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioAlarmGenericChange-Fourth 1
An generic change of a digital input/digital output/analog input has become active.
TRAP-TYPE    

ioInterfaceNumInputs-Fifth 1.3.6.1.4.1.818.1.2.5.1.1
The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceInputTable-Fifth 1.3.6.1.4.1.818.1.2.5.1.2
A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceInputEntry-Fifth

ioInterfaceInputEntry-Fifth 1.3.6.1.4.1.818.1.2.5.1.2.1
An entry containing information applicable to a particular input line.
OBJECT-TYPE    
  IoInterfaceInputEntry-Fifth  

ioInterfaceInputLineIndex-Fifth 1.3.6.1.4.1.818.1.2.5.1.2.1.1
The input line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceInputDescription-Fifth 1.3.6.1.4.1.818.1.2.5.1.2.1.2
A description of the alarm monitored by this input line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceInputStatus-Fifth 1.3.6.1.4.1.818.1.2.5.1.2.1.3
The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceEdgeMode-Fifth 1.3.6.1.4.1.818.1.2.5.1.2.1.4
Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

ioInterfaceAlarmMask-Fifth 1.3.6.1.4.1.818.1.2.5.1.2.1.5
Alarm functionality for the input line can be set active or inactive.
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceAlarmDelay-Fifth 1.3.6.1.4.1.818.1.2.5.1.2.1.6
Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceNumOutput-Fifth 1.3.6.1.4.1.818.1.2.5.2.1
The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceOutputTable-Fifth 1.3.6.1.4.1.818.1.2.5.2.2
A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceOutputEntry-Fifth

ioInterfaceOutputEntry-Fifth 1.3.6.1.4.1.818.1.2.5.2.2.1
An entry containing information applicable to a particular output line.
OBJECT-TYPE    
  IoInterfaceOutputEntry-Fifth  

ioInterfaceOutputLineIndex-Fifth 1.3.6.1.4.1.818.1.2.5.2.2.1.1
The output line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceOutputDescription-Fifth 1.3.6.1.4.1.818.1.2.5.2.2.1.2
A description of the alarm monitored by this output line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceOutputStatus-Fifth 1.3.6.1.4.1.818.1.2.5.2.2.1.3
The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceNumAnalogue-Fifth 1.3.6.1.4.1.818.1.2.5.3.1
The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceAnalogueTable-Fifth 1.3.6.1.4.1.818.1.2.5.3.2
A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceAnalogueEntry-Fifth

ioInterfaceAnalogueEntry-Fifth 1.3.6.1.4.1.818.1.2.5.3.2.1
An entry containing information applicable to a particular analogue line.
OBJECT-TYPE    
  IoInterfaceAnalogueEntry-Fifth  

ioInterfaceAnalogueLineIndex-Fifth 1.3.6.1.4.1.818.1.2.5.3.2.1.1
The analogue line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceAnalogueDescription-Fifth 1.3.6.1.4.1.818.1.2.5.3.2.1.2
A description of the alarm monitored by this analogue line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceAnalogueStatus-Fifth 1.3.6.1.4.1.818.1.2.5.3.2.1.3
Read analogue value 1, when the board support such functionality
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueLowThreshold-Fifth 1.3.6.1.4.1.818.1.2.5.3.2.1.4
Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueHighThreshold-Fifth 1.3.6.1.4.1.818.1.2.5.3.2.1.5
High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetLowThreshold-Fifth 1.3.6.1.4.1.818.1.2.5.3.2.1.6
After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetHighThreshold-Fifth 1.3.6.1.4.1.818.1.2.5.3.2.1.7
After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioAlarmGenericChange-Fifth 1
An generic change of a digital input/digital output/analog input has become active.
TRAP-TYPE    

ioInterfaceNumInputs-Sixth 1.3.6.1.4.1.818.1.2.6.1.1
The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceInputTable-Sixth 1.3.6.1.4.1.818.1.2.6.1.2
A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceInputEntry-Sixth

ioInterfaceInputEntry-Sixth 1.3.6.1.4.1.818.1.2.6.1.2.1
An entry containing information applicable to a particular input line.
OBJECT-TYPE    
  IoInterfaceInputEntry-Sixth  

ioInterfaceInputLineIndex-Sixth 1.3.6.1.4.1.818.1.2.6.1.2.1.1
The input line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceInputDescription-Sixth 1.3.6.1.4.1.818.1.2.6.1.2.1.2
A description of the alarm monitored by this input line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceInputStatus-Sixth 1.3.6.1.4.1.818.1.2.6.1.2.1.3
The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceEdgeMode-Sixth 1.3.6.1.4.1.818.1.2.6.1.2.1.4
Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

ioInterfaceAlarmMask-Sixth 1.3.6.1.4.1.818.1.2.6.1.2.1.5
Alarm functionality for the input line can be set active or inactive.
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceAlarmDelay-Sixth 1.3.6.1.4.1.818.1.2.6.1.2.1.6
Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceNumOutput-Sixth 1.3.6.1.4.1.818.1.2.6.2.1
The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceOutputTable-Sixth 1.3.6.1.4.1.818.1.2.6.2.2
A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceOutputEntry-Sixth

ioInterfaceOutputEntry-Sixth 1.3.6.1.4.1.818.1.2.6.2.2.1
An entry containing information applicable to a particular output line.
OBJECT-TYPE    
  IoInterfaceOutputEntry-Sixth  

ioInterfaceOutputLineIndex-Sixth 1.3.6.1.4.1.818.1.2.6.2.2.1.1
The output line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceOutputDescription-Sixth 1.3.6.1.4.1.818.1.2.6.2.2.1.2
A description of the alarm monitored by this output line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceOutputStatus-Sixth 1.3.6.1.4.1.818.1.2.6.2.2.1.3
The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceNumAnalogue-Sixth 1.3.6.1.4.1.818.1.2.6.3.1
The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceAnalogueTable-Sixth 1.3.6.1.4.1.818.1.2.6.3.2
A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceAnalogueEntry-Sixth

ioInterfaceAnalogueEntry-Sixth 1.3.6.1.4.1.818.1.2.6.3.2.1
An entry containing information applicable to a particular analogue line.
OBJECT-TYPE    
  IoInterfaceAnalogueEntry-Sixth  

ioInterfaceAnalogueLineIndex-Sixth 1.3.6.1.4.1.818.1.2.6.3.2.1.1
The analogue line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceAnalogueDescription-Sixth 1.3.6.1.4.1.818.1.2.6.3.2.1.2
A description of the alarm monitored by this analogue line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceAnalogueStatus-Sixth 1.3.6.1.4.1.818.1.2.6.3.2.1.3
Read analogue value 1, when the board support such functionality
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueLowThreshold-Sixth 1.3.6.1.4.1.818.1.2.6.3.2.1.4
Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueHighThreshold-Sixth 1.3.6.1.4.1.818.1.2.6.3.2.1.5
High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetLowThreshold-Sixth 1.3.6.1.4.1.818.1.2.6.3.2.1.6
After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetHighThreshold-Sixth 1.3.6.1.4.1.818.1.2.6.3.2.1.7
After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioAlarmGenericChange-Sixth 1
An generic change of a digital input/digital output/analog input has become active.
TRAP-TYPE    

ioInterfaceNumInputs-Seventh 1.3.6.1.4.1.818.1.2.7.1.1
The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceInputTable-Seventh 1.3.6.1.4.1.818.1.2.7.1.2
A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceInputEntry-Seventh

ioInterfaceInputEntry-Seventh 1.3.6.1.4.1.818.1.2.7.1.2.1
An entry containing information applicable to a particular input line.
OBJECT-TYPE    
  IoInterfaceInputEntry-Seventh  

ioInterfaceInputLineIndex-Seventh 1.3.6.1.4.1.818.1.2.7.1.2.1.1
The input line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceInputDescription-Seventh 1.3.6.1.4.1.818.1.2.7.1.2.1.2
A description of the alarm monitored by this input line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceInputStatus-Seventh 1.3.6.1.4.1.818.1.2.7.1.2.1.3
The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceEdgeMode-Seventh 1.3.6.1.4.1.818.1.2.7.1.2.1.4
Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

ioInterfaceAlarmMask-Seventh 1.3.6.1.4.1.818.1.2.7.1.2.1.5
Alarm functionality for the input line can be set active or inactive.
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceAlarmDelay-Seventh 1.3.6.1.4.1.818.1.2.7.1.2.1.6
Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceNumOutput-Seventh 1.3.6.1.4.1.818.1.2.7.2.1
The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceOutputTable-Seventh 1.3.6.1.4.1.818.1.2.7.2.2
A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceOutputEntry-Seventh

ioInterfaceOutputEntry-Seventh 1.3.6.1.4.1.818.1.2.7.2.2.1
An entry containing information applicable to a particular output line.
OBJECT-TYPE    
  IoInterfaceOutputEntry-Seventh  

ioInterfaceOutputLineIndex-Seventh 1.3.6.1.4.1.818.1.2.7.2.2.1.1
The output line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceOutputDescription-Seventh 1.3.6.1.4.1.818.1.2.7.2.2.1.2
A description of the alarm monitored by this output line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceOutputStatus-Seventh 1.3.6.1.4.1.818.1.2.7.2.2.1.3
The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceNumAnalogue-Seventh 1.3.6.1.4.1.818.1.2.7.3.1
The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceAnalogueTable-Seventh 1.3.6.1.4.1.818.1.2.7.3.2
A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceAnalogueEntry-Seventh

ioInterfaceAnalogueEntry-Seventh 1.3.6.1.4.1.818.1.2.7.3.2.1
An entry containing information applicable to a particular analogue line.
OBJECT-TYPE    
  IoInterfaceAnalogueEntry-Seventh  

ioInterfaceAnalogueLineIndex-Seventh 1.3.6.1.4.1.818.1.2.7.3.2.1.1
The analogue line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceAnalogueDescription-Seventh 1.3.6.1.4.1.818.1.2.7.3.2.1.2
A description of the alarm monitored by this analogue line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceAnalogueStatus-Seventh 1.3.6.1.4.1.818.1.2.7.3.2.1.3
Read analogue value 1, when the board support such functionality
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueLowThreshold-Seventh 1.3.6.1.4.1.818.1.2.7.3.2.1.4
Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueHighThreshold-Seventh 1.3.6.1.4.1.818.1.2.7.3.2.1.5
High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetLowThreshold-Seventh 1.3.6.1.4.1.818.1.2.7.3.2.1.6
After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetHighThreshold-Seventh 1.3.6.1.4.1.818.1.2.7.3.2.1.7
After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioAlarmGenericChange-Seventh 1
An generic change of a digital input/digital output/analog input has become active.
TRAP-TYPE    

ioInterfaceNumInputs-Eighth 1.3.6.1.4.1.818.1.2.8.1.1
The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceInputTable-Eighth 1.3.6.1.4.1.818.1.2.8.1.2
A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceInputEntry-Eighth

ioInterfaceInputEntry-Eighth 1.3.6.1.4.1.818.1.2.8.1.2.1
An entry containing information applicable to a particular input line.
OBJECT-TYPE    
  IoInterfaceInputEntry-Eighth  

ioInterfaceInputLineIndex-Eighth 1.3.6.1.4.1.818.1.2.8.1.2.1.1
The input line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceInputDescription-Eighth 1.3.6.1.4.1.818.1.2.8.1.2.1.2
A description of the alarm monitored by this input line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceInputStatus-Eighth 1.3.6.1.4.1.818.1.2.8.1.2.1.3
The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceEdgeMode-Eighth 1.3.6.1.4.1.818.1.2.8.1.2.1.4
Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

ioInterfaceAlarmMask-Eighth 1.3.6.1.4.1.818.1.2.8.1.2.1.5
Alarm functionality for the input line can be set active or inactive.
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceAlarmDelay-Eighth 1.3.6.1.4.1.818.1.2.8.1.2.1.6
Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceNumOutput-Eighth 1.3.6.1.4.1.818.1.2.8.2.1
The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceOutputTable-Eighth 1.3.6.1.4.1.818.1.2.8.2.2
A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceOutputEntry-Eighth

ioInterfaceOutputEntry-Eighth 1.3.6.1.4.1.818.1.2.8.2.2.1
An entry containing information applicable to a particular output line.
OBJECT-TYPE    
  IoInterfaceOutputEntry-Eighth  

ioInterfaceOutputLineIndex-Eighth 1.3.6.1.4.1.818.1.2.8.2.2.1.1
The output line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceOutputDescription-Eighth 1.3.6.1.4.1.818.1.2.8.2.2.1.2
A description of the alarm monitored by this output line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceOutputStatus-Eighth 1.3.6.1.4.1.818.1.2.8.2.2.1.3
The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
OBJECT-TYPE    
  Integer32 inactive(0), active(1)  

ioInterfaceNumAnalogue-Eighth 1.3.6.1.4.1.818.1.2.8.3.1
The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
OBJECT-TYPE    
  NonNegativeInteger32  

ioInterfaceAnalogueTable-Eighth 1.3.6.1.4.1.818.1.2.8.3.2
A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
OBJECT-TYPE    
  SEQUENCE OF  
    IoInterfaceAnalogueEntry-Eighth

ioInterfaceAnalogueEntry-Eighth 1.3.6.1.4.1.818.1.2.8.3.2.1
An entry containing information applicable to a particular analogue line.
OBJECT-TYPE    
  IoInterfaceAnalogueEntry-Eighth  

ioInterfaceAnalogueLineIndex-Eighth 1.3.6.1.4.1.818.1.2.8.3.2.1.1
The analogue line identifier.
OBJECT-TYPE    
  PositiveInteger32  

ioInterfaceAnalogueDescription-Eighth 1.3.6.1.4.1.818.1.2.8.3.2.1.2
A description of the alarm monitored by this analogue line.
OBJECT-TYPE    
  DisplayString Size(0..63)  

ioInterfaceAnalogueStatus-Eighth 1.3.6.1.4.1.818.1.2.8.3.2.1.3
Read analogue value 1, when the board support such functionality
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueLowThreshold-Eighth 1.3.6.1.4.1.818.1.2.8.3.2.1.4
Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueHighThreshold-Eighth 1.3.6.1.4.1.818.1.2.8.3.2.1.5
High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetLowThreshold-Eighth 1.3.6.1.4.1.818.1.2.8.3.2.1.6
After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioInterfaceAnalogueResetHighThreshold-Eighth 1.3.6.1.4.1.818.1.2.8.3.2.1.7
After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
OBJECT-TYPE    
  Integer32  

ioAlarmGenericChange-Eighth 1
An generic change of a digital input/digital output/analog input has become active.
TRAP-TYPE    

geModemStatus 1.3.6.1.4.1.818.1.3.1
The status of the modem, controlled by the addressed device. The status word is a collection of bits, as specified below. The SNMP value NOSUCHNAME means 'status not (yet) available'. 1 modemStatOnline. There is a valid online connection. 2 modemStatError. The last operation has failed. The device will clear this bit when a new modem command is received. 4 unused (should be defined = 0). 8 unused (should be defined = 0). 16 modemStatDialling. The dialling procedure is pending. 32 modemStatBusy. The device is performing some operation, and can not be accessed, temporarily. 64 unused (should be defined = 0). 128 modemStatNoModem. The modem is not connected or not responding. 256 modemStatDCD. The DCD line status signal is on. 512 modemStatRing. The RING line status signal is on. 1024 modemStatCTS. The CTS line status signal is on. 2048 modemStatDSR. The DSR line status signal is on. 4096 unused (should be defined = 0). 8192 unused (should be defined = 0). 16384 unused (should be defined = 0). 32768 unused (should be defined = 0).
OBJECT-TYPE    
  NonNegativeInteger32  

geModemNumInitString 1.3.6.1.4.1.818.1.3.2
The number of modem init strings utilized by this ups. This entry indicates the number of rows in the init string table.
OBJECT-TYPE    
  NonNegativeInteger32  

geModemInitStringTable 1.3.6.1.4.1.818.1.3.3
A list of init string table entries. The number of entries is given by the value of geModemNumInitString.
OBJECT-TYPE    
  SEQUENCE OF  
    GeModemInitStringEntry

geModemInitStringEntry 1.3.6.1.4.1.818.1.3.3.1
An entry containing information applicable to a particular Init string.
OBJECT-TYPE    
  GeModemInitStringEntry  

geModemInitStringLineIndex 1.3.6.1.4.1.818.1.3.3.1.1
The Init string line identifier.
OBJECT-TYPE    
  PositiveInteger32  

geModemInitstring 1.3.6.1.4.1.818.1.3.3.1.2
A modem Init string.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geModemNumPhoneNumber 1.3.6.1.4.1.818.1.3.4
The number of modem phone numbers utilized by this ups. This entry indicates the number of rows in the table.
OBJECT-TYPE    
  NonNegativeInteger32  

geModemPhoneNumberTable 1.3.6.1.4.1.818.1.3.5
A list of phone number table entries. The number of entries is given by the value of geModemNumPhoneNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    GeModemPhoneNumberEntry

geModemPhoneNumberEntry 1.3.6.1.4.1.818.1.3.5.1
An entry containing information applicable to a particular phone number.
OBJECT-TYPE    
  GeModemPhoneNumberEntry  

geModemPhoneNumberLineIndex 1.3.6.1.4.1.818.1.3.5.1.1
The phone number line identifier.
OBJECT-TYPE    
  PositiveInteger32  

geModemPhoneNumber 1.3.6.1.4.1.818.1.3.5.1.2
A phone number.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geClientProcessor 1.3.6.1.4.1.818.2.1.1
The processor used by the clients machine.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geClientOperatingSystem 1.3.6.1.4.1.818.2.1.2
Operating system on which the client runs.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geClientJavaRuntimeVersion 1.3.6.1.4.1.818.2.1.3
JavaRuntimeVersion of the client machine.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geClientMaxSizeOfLogfiles 1.3.6.1.4.1.818.2.1.4
The max. size of the logfiles in Kb.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientLanguageSelection 1.3.6.1.4.1.818.2.1.5
Shows the currently activated language of the client.
OBJECT-TYPE    
  DisplayString Size(0..32)  

geClientInternalCommunicationPort 1.3.6.1.4.1.818.2.1.6
UDP port used between server and client part.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientReboot 1.3.6.1.4.1.818.2.1.7
setting this object causes the protection client to reboot and activate new settings.
OBJECT-TYPE    
  Integer32 reboot(1)  

geClientNumUPS 1.3.6.1.4.1.818.2.1.8
The number of UPSs utilized by this client. This entry indicates the number of rows in the table.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientUPSTable 1.3.6.1.4.1.818.2.1.9
A list of UPS table entries. The number of entries is given by the value of geClientNumUPS.
OBJECT-TYPE    
  SEQUENCE OF  
    GeClientUPSEntry

geClientUPSEntry 1.3.6.1.4.1.818.2.1.9.1
An entry containing information applicable to a particular UPS.
OBJECT-TYPE    
  GeClientUPSEntry  

geClientUPSLineIndex 1.3.6.1.4.1.818.2.1.9.1.1
The UPS line identifier.
OBJECT-TYPE    
  PositiveInteger32  

geClientUPSName 1.3.6.1.4.1.818.2.1.9.1.2
The administrative name of the UPS.
OBJECT-TYPE    
  DisplayString Size(0..32)  

geClientUPSCommunicationType 1.3.6.1.4.1.818.2.1.9.1.3
The method of communication.
OBJECT-TYPE    
  Integer32 serial(0), snmp(1)  

geClientUPSCommunicationPort 1.3.6.1.4.1.818.2.1.9.1.4
The communication port.
OBJECT-TYPE    
  DisplayString Size(0..32)  

geClientUPSReadCommName 1.3.6.1.4.1.818.2.1.9.1.5
The Read community string. Used when communication method is SNMP.
OBJECT-TYPE    
  DisplayString Size(0..32)  

geClientUPSWriteCommName 1.3.6.1.4.1.818.2.1.9.1.6
The Write community string. Used when communication method is SNMP.
OBJECT-TYPE    
  DisplayString Size(0..32)  

geClientUPSCommRetries 1.3.6.1.4.1.818.2.1.9.1.7
Number of retries in case an answer times out. When the max. number of retries is reached a lost communication alarm will be raised.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientAlarmManagement 1.3.6.1.4.1.818.2.1.9.1.8
Alarm Management enabled or disabled.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

geClientPreDelay 1.3.6.1.4.1.818.2.1.9.1.9
The number of second an alarm needs to be active before action is taken.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientSystemShutdown 1.3.6.1.4.1.818.2.1.9.1.10
Specifies whether the client should shutdown the machine when an alarm situation occurs.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

geClientRuntime 1.3.6.1.4.1.818.2.1.9.1.11
The user defined preferable runtime.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientUPSShutdown 1.3.6.1.4.1.818.2.1.9.1.12
Defines whether the UPS will be shut down after an Operating System shutdown.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

geClientMaxScriptExecutionTime 1.3.6.1.4.1.818.2.1.9.1.13
The max. number of seconds the script file is allowed to run.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientGraceperiod 1.3.6.1.4.1.818.2.1.9.1.14
The time between start of the Operating System shutdown and the UPS shutdown.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientNumTests 1.3.6.1.4.1.818.2.1.20
The number of scheduled tests. This entry indicates the number of rows in the table.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientTestTable 1.3.6.1.4.1.818.2.1.21
A list of test table entries. The number of entries is given by the value of geClientNumTests.
OBJECT-TYPE    
  SEQUENCE OF  
    GeClientTestEntry

geClientTestEntry 1.3.6.1.4.1.818.2.1.21.1
An entry containing information applicable to a particular Test.
OBJECT-TYPE    
  GeClientTestEntry  

geClientTestLineIndex 1.3.6.1.4.1.818.2.1.21.1.1
The test line identifier.
OBJECT-TYPE    
  PositiveInteger32  

geClientTestId 1.3.6.1.4.1.818.2.1.21.1.2
The test Id.
OBJECT-TYPE    
  Integer32  

geClientTestDayTime 1.3.6.1.4.1.818.2.1.21.1.3
The time on which the test is due to be performed.
OBJECT-TYPE    
  Integer32  

geClientTestWeekDay 1.3.6.1.4.1.818.2.1.21.1.4
The day in the week on which the test will be performed.
OBJECT-TYPE    
  Integer32  

geClientTestMonthDay 1.3.6.1.4.1.818.2.1.21.1.5
The month day on which the test will be performed.
OBJECT-TYPE    
  Integer32  

geClientNumShutdowns 1.3.6.1.4.1.818.2.1.30
The number of scheduled Shutdowns. This entry indicates the number of rows in the table.
OBJECT-TYPE    
  NonNegativeInteger32  

geClientShutdownTable 1.3.6.1.4.1.818.2.1.31
A list of Shutdown table entries. The number of entries is given by the value of geClientNumShutdowns.
OBJECT-TYPE    
  SEQUENCE OF  
    GeClientShutdownEntry

geClientShutdownEntry 1.3.6.1.4.1.818.2.1.31.1
An entry containing information applicable to a particular Shutdown.
OBJECT-TYPE    
  GeClientShutdownEntry  

geClientShutdownLineIndex 1.3.6.1.4.1.818.2.1.31.1.1
The Shutdown line identifier.
OBJECT-TYPE    
  PositiveInteger32  

geClientShutdownDelay 1.3.6.1.4.1.818.2.1.31.1.2
The delay before start of the Shutdown.
OBJECT-TYPE    
  Integer32  

geClientShutdownDuration 1.3.6.1.4.1.818.2.1.31.1.3
The duration of the Shutdown.
OBJECT-TYPE    
  Integer32  

geClientShutdownDayTime 1.3.6.1.4.1.818.2.1.31.1.4
The time on which the Shutdown is due to be performed.
OBJECT-TYPE    
  Integer32  

geClientShutdownWeekDay 1.3.6.1.4.1.818.2.1.31.1.5
The day in the week on which the Shutdown will be performed.
OBJECT-TYPE    
  Integer32  

geClientShutdownMonthDay 1.3.6.1.4.1.818.2.1.31.1.6
The month day on which the Shutdown will be performed.
OBJECT-TYPE    
  Integer32  

geClientShutdownPreWarnTime 1.3.6.1.4.1.818.2.1.31.1.7
The number of seconds before start of the shutdown a pre warning will be raised.
OBJECT-TYPE    
  Integer32  

geAgentUDPPort 1.3.6.1.4.1.818.3.1.1
The UDP port number used by agent.
OBJECT-TYPE    
  NonNegativeInteger32  

geAgentWebServerPort 1.3.6.1.4.1.818.3.1.2
The UDP port number used by the HTTP server.
OBJECT-TYPE    
  NonNegativeInteger32  

geAgentComPort 1.3.6.1.4.1.818.3.1.3
The COM port used by the agent.
OBJECT-TYPE    
  DisplayString Size(0..32)  

geAgentComTimeout 1.3.6.1.4.1.818.3.1.4
The Timeout delay in seconds of the serial communication.
OBJECT-TYPE    
  NonNegativeInteger32  

geAgentComRetries 1.3.6.1.4.1.818.3.1.5
The number of retries when serial communication fails.
OBJECT-TYPE    
  NonNegativeInteger32  

geAgentReadCommunity 1.3.6.1.4.1.818.3.1.6
The read community string of the agent.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geAgentWriteCommunity 1.3.6.1.4.1.818.3.1.7
The write community string of the agent.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geAgentResponsibleEmailAddress 1.3.6.1.4.1.818.3.1.8
The email address of the responsible person for this agent.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geRFCTrapsToSend 1.3.6.1.4.1.818.3.1.9
This object defines whether RFC traps need to be send. The bit value 1 indicates that the traps needs to be send, while value 0 does not result in a trap to send.
OBJECT-TYPE    
  Integer32 off(0), on(1)  

geIMVTrapsToSend 1.3.6.1.4.1.818.3.1.10
This object defines for which device(s) IMV traps need to be send. The bit value 1 indicates that the trap needs to be send, while value 0 does not result in a trap to send. The value presents the devices as a mask: 1 GenericUPS 2 FirstUPS 4 SecondUPS 8 ThirdUPS 16 FourthUPS 32 FifthUPS 64 SixthUPS 128 SeventhUPS 256 EigthUPS 512 IOInterface
OBJECT-TYPE    
  NonNegativeInteger32  

geAgentNumTraps 1.3.6.1.4.1.818.3.2.1
The number of configured traps. This entry indicates the number of rows in the table.
OBJECT-TYPE    
  NonNegativeInteger32  

geAgentTrapTable 1.3.6.1.4.1.818.3.2.2
A list of trap table entries. The number of entries is given by the value of geAgentNumTraps.
OBJECT-TYPE    
  SEQUENCE OF  
    GeAgentTrapEntry

geAgentTrapEntry 1.3.6.1.4.1.818.3.2.2.1
An entry containing information applicable to a particular trap target.
OBJECT-TYPE    
  GeAgentTrapEntry  

geAgentTrapLineIndex 1.3.6.1.4.1.818.3.2.2.1.1
The Trap line identifier.
OBJECT-TYPE    
  PositiveInteger32  

geAgentTrapAddress 1.3.6.1.4.1.818.3.2.2.1.2
The destination IP-address of the trap.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geAgentTrapCommunity 1.3.6.1.4.1.818.3.2.2.1.3
The communication string used by the trap.
OBJECT-TYPE    
  DisplayString Size(0..63)  

geAgentTrapPort 1.3.6.1.4.1.818.3.2.2.1.4
The UDP port on the receiving side.
OBJECT-TYPE    
  Integer32  

upsIdentManufacturer-first 1.3.6.1.4.1.818.1.1.11.1.1
The name of the UPS manufacturer.(*)
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsIdentModel-first 1.3.6.1.4.1.818.1.1.11.1.2
The UPS Model designation.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentUPSSoftwareVersion-first 1.3.6.1.4.1.818.1.1.11.1.3
The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentAgentSoftwareVersion-first 1.3.6.1.4.1.818.1.1.11.1.4
The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentName-first 1.3.6.1.4.1.818.1.1.11.1.5
A string identifying the UPS. This object should be set by the administrator.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentAttachedDevices-first 1.3.6.1.4.1.818.1.1.11.1.6
A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentUPSSerialNumber-first 1.3.6.1.4.1.818.1.1.11.1.7
The UPS serial number
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsIdentComProtVersion-first 1.3.6.1.4.1.818.1.1.11.1.8
The IMV communication protocol version
OBJECT-TYPE    
  DisplayString Size(0..15)  

upsIdentOperatingTime-first 1.3.6.1.4.1.818.1.1.11.1.9
The present value of the operating time. total 'on' time since UPS manufactured
OBJECT-TYPE    
  NonNegativeInteger32  

upsBatteryStatus-first 1.3.6.1.4.1.818.1.1.11.2.1
The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
OBJECT-TYPE    
  Integer32 unknown(1), batteryNormal(2), batteryLow(3), batteryDepleted(4)  

upsSecondsOnBattery-first 1.3.6.1.4.1.818.1.1.11.2.2
If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsEstimatedMinutesRemaining-first 1.3.6.1.4.1.818.1.1.11.2.3
An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
OBJECT-TYPE    
  PositiveInteger32  

upsEstimatedChargeRemaining-first 1.3.6.1.4.1.818.1.1.11.2.4
An estimate of the battery charge remaining expressed as a percent of full charge.(*)
OBJECT-TYPE    
  Integer32 0..100  

upsBatteryVoltage-first 1.3.6.1.4.1.818.1.1.11.2.5
The magnitude of the present battery voltage.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsBatteryCurrent-first 1.3.6.1.4.1.818.1.1.11.2.6
The present battery current.(*)
OBJECT-TYPE    
  Integer32  

upsBatteryTemperature-first 1.3.6.1.4.1.818.1.1.11.2.7
The ambient temperature at or near the UPS Battery casing.(*)
OBJECT-TYPE    
  Integer32  

upsInputLineBads-first 1.3.6.1.4.1.818.1.1.11.3.1
A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
OBJECT-TYPE    
  Counter32  

upsInputNumLines-first 1.3.6.1.4.1.818.1.1.11.3.2
The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputTable-first 1.3.6.1.4.1.818.1.1.11.3.3
A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
OBJECT-TYPE    
  SEQUENCE OF  
    UpsInputEntry-first

upsInputEntry-first 1.3.6.1.4.1.818.1.1.11.3.3.1
An entry containing information applicable to a particular input line.(*)
OBJECT-TYPE    
  UpsInputEntry-first  

upsInputLineIndex-first 1.3.6.1.4.1.818.1.1.11.3.3.1.1
The input line identifier.(*)
OBJECT-TYPE    
  PositiveInteger32  

upsInputFrequency-first 1.3.6.1.4.1.818.1.1.11.3.3.1.2
The present input frequency.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputVoltage-first 1.3.6.1.4.1.818.1.1.11.3.3.1.3
The magnitude of the present input voltage.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputCurrent-first 1.3.6.1.4.1.818.1.1.11.3.3.1.4
The magnitude of the present input current.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputTruePower-first 1.3.6.1.4.1.818.1.1.11.3.3.1.5
The magnitude of the present input true power.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputVoltageMin-first 1.3.6.1.4.1.818.1.1.11.3.3.1.6
The lowest magnitude of the input voltage since last read out.
OBJECT-TYPE    
  NonNegativeInteger32  

upsInputVoltageMax-first 1.3.6.1.4.1.818.1.1.11.3.3.1.7
The highest magnitude of the input voltage since last read out.
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputSource-first 1.3.6.1.4.1.818.1.1.11.4.1
The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
OBJECT-TYPE    
  Integer32 other(1), none(2), normal(3), bypass(4), battery(5), booster(6), reducer(7)  

upsOutputFrequency-first 1.3.6.1.4.1.818.1.1.11.4.2
The present output frequency.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputNumLines-first 1.3.6.1.4.1.818.1.1.11.4.3
The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputTable-first 1.3.6.1.4.1.818.1.1.11.4.4
A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
OBJECT-TYPE    
  SEQUENCE OF  
    UpsOutputEntry-first

upsOutputEntry-first 1.3.6.1.4.1.818.1.1.11.4.4.1
An entry containing information applicable to a particular output line.(*)
OBJECT-TYPE    
  UpsOutputEntry-first  

upsOutputLineIndex-first 1.3.6.1.4.1.818.1.1.11.4.4.1.1
The output line identifier.(*)
OBJECT-TYPE    
  PositiveInteger32  

upsOutputVoltage-first 1.3.6.1.4.1.818.1.1.11.4.4.1.2
The present output voltage.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputCurrent-first 1.3.6.1.4.1.818.1.1.11.4.4.1.3
The present output current.(*)
OBJECT-TYPE    
  NonNegativeInteger32  

upsOutputPower-first 1.3.6.1.4.1.818.1.1.11.4.4.1.4
The present output true power.(*)
OBJECT-TYPE    
&