GDSFrameRelay-MIB

File: GDSFrameRelay-MIB.mib (35299 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212

Imported symbols

enterprises Counter IpAddress
DisplayString OBJECT-TYPE

Defined Types

Unit-States  
SEQUENCE    
  uOwn-SID INTEGER
  uCurrent-Date DisplayString
  uCurrent-Time DisplayString
  uDevice-State INTEGER
  uComms-State INTEGER
  uNMS-State INTEGER
  uSM-State INTEGER
  uReady-Alarm-Led INTEGER
  uRAG-tests Counter
  uRAG-fails Counter
  uRAG-threshold Counter

FR-Traffic-Entry  
SEQUENCE    
  frPort-Index INTEGER
  frPort-Type INTEGER
  frGood-Frames Counter
  frBad-Frames Counter
  frInactive-DLCI Counter
  frReceived-FECN Counter
  frReceived-BECN Counter
  frSent-Frames Counter
  frDropped-Frames Counter

FR-RX-Err-Entry  
SEQUENCE    
  frRxErrIndex INTEGER
  frRxErrShort-Frames Counter
  frRxErrAborted-Frames Counter
  frRxErrResidual-Bits Counter
  frRxErrOverruns Counter
  frRxErrCRC-Errors Counter

Pi-FR-DLC-Ranges-Entry  
SEQUENCE    
  piFRDLcRangeBand INTEGER
  piFRDLcRangeUse INTEGER
  piFRDLcRangeMode INTEGER
  piFRDLcRangeStart INTEGER
  piFRDLcRangeEnd-set-to-activate-changes INTEGER

Pi-App-DLC-Cipher-Entry  
SEQUENCE    
  piAppDLcCipherBand INTEGER
  piAppDLcCipherUse INTEGER
  piAppDLcCipherStart INTEGER
  piAppDLcCipherEnd-set-to-activate-changes INTEGER

Defined Values

gds 1.3.6.1.4.1.1955
OBJECT IDENTIFIER    

seriesfr 1.3.6.1.4.1.1955.5
OBJECT IDENTIFIER    

is-GDS-frame-relay-device5 1.3.6.1.4.1.1955.5.5
OBJECT IDENTIFIER    

unit 1.3.6.1.4.1.1955.5.5.1
OBJECT IDENTIFIER    

frame-relay 1.3.6.1.4.1.1955.5.5.2
OBJECT IDENTIFIER    

configure 1.3.6.1.4.1.1955.5.5.3
OBJECT IDENTIFIER    

uVersion-Strings 1.3.6.1.4.1.1955.5.5.1.1
OBJECT IDENTIFIER    

uMain-HW-Version 1.3.6.1.4.1.1955.5.5.1.1.1
The frame relay encryptor mainboard HW version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

uComm-HW-Version 1.3.6.1.4.1.1955.5.5.1.1.2
The frame relay encryptor commsboard HW version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

uMain-SW-Version 1.3.6.1.4.1.1955.5.5.1.1.3
The frame relay encryptor mainboard SW version. Every effort will be made by GDS to make the MIB backwards compatible to the frame relay encryptor software. In case of doubt or queries please quote the following release number. Enterprise MIB Version Release V1.8p
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

uComm-SW-Version 1.3.6.1.4.1.1955.5.5.1.1.4
The frame relay encryptor comms board SW version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

uAlgorithm 1.3.6.1.4.1.1955.5.5.1.1.5
The frame relay encryptor encryption algorithm DES or GDS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

uAccess-Table 1.3.6.1.4.1.1955.5.5.1.1.6
The frame relay encryptor access control table version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

uConfigured 1.3.6.1.4.1.1955.5.5.1.2
OBJECT IDENTIFIER    

uOwn-SID 1.3.6.1.4.1.1955.5.5.1.2.1
The Station Identity of this frame relay encryptor .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

uDynamic 1.3.6.1.4.1.1955.5.5.1.3
OBJECT IDENTIFIER    

uCurrent-Date 1.3.6.1.4.1.1955.5.5.1.3.1
The uCurrentTime indicates the current date of the frame relay encryptor . Date is in the format dd/mm/yy.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(8)  

uCurrent-Time 1.3.6.1.4.1.1955.5.5.1.3.2
The uCurrentTime indicates the current time of the frame relay encryptor . Time is in the format hh:mm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(5)  

uDevice-State 1.3.6.1.4.1.1955.5.5.1.3.3
The current state of the frame relay encryptor . There are two test states: test-empty with no security parameters loaded test-loaded which is entered with live parameters from the live state
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), test-empty(2), test-loaded(3), failure(4), fail-cipher-chip(5), fail-lock-open(6), fail-lock-open-and-cipher-chip(7)  

uComms-State 1.3.6.1.4.1.1955.5.5.1.3.4
The current state of the frame relay encryptor comms board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER booting(1), encrypting(2), not-encrypting(3), failure(4)  

uNMS-State 1.3.6.1.4.1.1955.5.5.1.3.5
The current state of the SNMP agent for NMS requests. Only in the writeenabled state are Sets allowed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), read-only(2), read-write(3)  

uSM-State 1.3.6.1.4.1.1955.5.5.1.3.6
The current state of the Right SM module. This should be checked after parameter updates in the configure group or the MIBII system group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), removed(2), failure(3)  

uReady-Alarm-Led 1.3.6.1.4.1.1955.5.5.1.3.7
The state of the front panel LED red: GRETACODER is in Test Mode green: GRETACODER is in Normal Mode yellow: GRETACODER is performing a self test blinking-red: GRETACODER is in Failure state blinking-yellow: GRETACODER MMI user is logged-in
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER red-test-mode(1), green-normal(2), yellow-self-testing(3), flashing-red-alarm(9), flashing-yellow-user-logged-in(11)  

uBackground 1.3.6.1.4.1.1955.5.5.1.4
OBJECT IDENTIFIER    

uRAG-tests 1.3.6.1.4.1.1955.5.5.1.4.1
The total number of Random Number Generator tests made A test is made once per minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

uRAG-fails 1.3.6.1.4.1.1955.5.5.1.4.2
The total number of Random Number Generator failures recorded
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

uRAG-threshold 1.3.6.1.4.1.1955.5.5.1.4.3
The number of failures that should trigger a Trap. Changing this value also clears the tests and fails counters
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

reset-FR-statistic-counters 1.3.6.1.4.1.1955.5.5.2.1
This command clears all the frame relay statistical counters for both ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

fR-Traffic-Table 1.3.6.1.4.1.1955.5.5.2.2
The Statistics Table for the frame relay encryptor .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FR-Traffic-Entry

fR-Traffic-Entry 1.3.6.1.4.1.1955.5.5.2.2.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FR-Traffic-Entry  

frPort-Index 1.3.6.1.4.1.1955.5.5.2.2.1.1
Port Number Index. The ifIndex Value of the corresponding ifEntry from rfc1213.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frPort-Type 1.3.6.1.4.1.1955.5.5.2.2.1.2
Plain is on the local side, cipher the network
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER plain-port(1), cipher-port(2)  

frGood-Frames 1.3.6.1.4.1.1955.5.5.2.2.1.3
The total number of frames received by the frame relay encryptor on a port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frBad-Frames 1.3.6.1.4.1.1955.5.5.2.2.1.4
The number of bad frames received by the frame relay encryptor on a port. These are classified further in frRxErrTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frInactive-DLCI 1.3.6.1.4.1.1955.5.5.2.2.1.5
The number of illegal or unknown DLCIs received by the frame relay encryptor on a port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frReceived-FECN 1.3.6.1.4.1.1955.5.5.2.2.1.6
The number of frames with a forward congestion notification received by the frame relay encryptor on a port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frReceived-BECN 1.3.6.1.4.1.1955.5.5.2.2.1.7
The number of frames with a backward congestion notification received by the frame relay encryptor on a port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frSent-Frames 1.3.6.1.4.1.1955.5.5.2.2.1.8
The total number of frames transmitted by the frame relay encryptor on a port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frDropped-Frames 1.3.6.1.4.1.1955.5.5.2.2.1.9
The total number of TX frames dropped by the frame relay encryptor on a port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

fR-RX-Err-Table 1.3.6.1.4.1.1955.5.5.2.3
The receive error information for a frame relay encryptor frame relay port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FR-RX-Err-Entry

fR-RX-Err-Entry 1.3.6.1.4.1.1955.5.5.2.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FR-RX-Err-Entry  

frRxErrIndex 1.3.6.1.4.1.1955.5.5.2.3.1.1
Port Number Index. The ifIndex Value of the corresponding ifEntry from rfc1213.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frRxErrShort-Frames 1.3.6.1.4.1.1955.5.5.2.3.1.2
The number of short frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frRxErrAborted-Frames 1.3.6.1.4.1.1955.5.5.2.3.1.3
The number of aborted frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frRxErrResidual-Bits 1.3.6.1.4.1.1955.5.5.2.3.1.4
The number of residual bit frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frRxErrOverruns 1.3.6.1.4.1.1955.5.5.2.3.1.5
The number of overruns received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frRxErrCRC-Errors 1.3.6.1.4.1.1955.5.5.2.3.1.6
The number of CRC errors received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pi-FR-Layer1 1.3.6.1.4.1.1955.5.5.3.1
OBJECT IDENTIFIER    

piFRInterface-Installed 1.3.6.1.4.1.1955.5.5.3.1.1
The type of Frame Relay Physical interface. The following parameters are required for: - RS422/V35/X21 clock source - G703 E1 impedance, framemode, timeslots - T1 T1 frame mode, timeslots.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER is-RS422(1), is-V35(2), is-T1(3), is-E1(4), is-X21(5), is-undefined(6)  

piFRTX-Clock-Source 1.3.6.1.4.1.1955.5.5.3.1.2
Required if the physical type is: RS422 V.35 X.21
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER is-DCE(1), is-DTE(2)  

piFRE1-Plain-Port-Impedance 1.3.6.1.4.1.1955.5.5.3.1.3
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER is-75-OHMS-BNC(1), is-120-OHMS-D-SUB(2)  

piFRE1-Cipher-Port-Impedance 1.3.6.1.4.1.1955.5.5.3.1.4
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER is-75-OHMS-BNC(1), is-120-OHMS-D-SUB(2)  

piFRE1-Framing-Mode 1.3.6.1.4.1.1955.5.5.3.1.5
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER is-unframed(1), is-G704(2)  

piFRE1-Time-Slot-Options 1.3.6.1.4.1.1955.5.5.3.1.6
Required if the physical type is G703 (E1) E1 time slot options available: Bit values shown in piFRE1-Time-Slots all slots, except TS0 0xff, 0xff, 0xff, 0xfe all slots, except TS0,TS16 0xff, 0xfe, 0xff, 0xfe
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER all-slots-except-TS0(1), all-slots-except-TS0-and-TS16(2)  

piFRE1-Time-Slots 1.3.6.1.4.1.1955.5.5.3.1.7
An Octet bit string. Each bit defines an E1 time slot: 0= not used for frame relay 1= used for frame relay
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

piFRT1-Plain-Port-Pulse 1.3.6.1.4.1.1955.5.5.3.1.8
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER is-CSU(1), is-CSU-T1C1(2), is-DSX-1-0-40m(3), is-DSX-1-40-80m(4), is-DSX-1-80-120m(5), is-DSX-1-120-160m(6), is-DSX-1-160-200m(7)  

piFRT1-Cipher-Port-Pulse 1.3.6.1.4.1.1955.5.5.3.1.9
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER is-CSU(1), is-CSU-T1C1(2), is-DSX-1-0-40m(3), is-DSX-1-40-80m(4), is-DSX-1-80-120m(5), is-DSX-1-120-160m(6), is-DSX-1-160-200m(7)  

piFRT1-Framing-Mode 1.3.6.1.4.1.1955.5.5.3.1.10
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER is-unframed(1), is-ESF(3), is-D4(4)  

piFRT1-Time-Slot-Options 1.3.6.1.4.1.1955.5.5.3.1.11
Required if the physical type is T1 T1 time slot options available: Bit values shown in piFRT1TimeSlots all slots 0xff, 0xff, 0xff
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER all-slots(1)  

piFRT1-Time-Slots 1.3.6.1.4.1.1955.5.5.3.1.12
An Octet bit string. Each bit defines a T1 time slot: 0= not used for frame relay 1= used for frame relay
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

pi-FR-Layer2 1.3.6.1.4.1.1955.5.5.3.2
OBJECT IDENTIFIER    

pi-FR-Logical-Interface-Type 1.3.6.1.4.1.1955.5.5.3.2.1
The type of Frame Relay logical interface. UNI = User to Network Interface NNI = Network to Network Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER uni(1), nni(2)  

pi-FR-Max-RX-Frame 1.3.6.1.4.1.1955.5.5.3.2.2
Maximum frame length in octets incoming
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER size-256-bytes(256), size-512-bytes(512), size-1024-bytes(1024), size-1600-bytes(1600), size-2048-bytes(2048), size-4096-bytes(4096)  

pi-FR-Max-TX-Frame 1.3.6.1.4.1.1955.5.5.3.2.3
Maximum frame length in octets outgoing
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER size-256-bytes(256), size-512-bytes(512), size-1024-bytes(1024), size-1600-bytes(1600), size-2048-bytes(2048), size-4096-bytes(4096)  

pi-FR-LMI-support 1.3.6.1.4.1.1955.5.5.3.2.4
LMI version
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), standard-LMI(2), is-ANSI-T1-617(3), is-ITU-T-Q933(4)  

pi-FR-DLC-Ranges-Table 1.3.6.1.4.1.1955.5.5.3.3
The Table of Active DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Pi-FR-DLC-Ranges-Entry

pi-FR-DLC-Ranges-Entry 1.3.6.1.4.1.1955.5.5.3.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Pi-FR-DLC-Ranges-Entry  

piFRDLcRangeBand 1.3.6.1.4.1.1955.5.5.3.3.1.1
The index number of this DLCI circuit band.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

piFRDLcRangeUse 1.3.6.1.4.1.1955.5.5.3.3.1.2
The Type of use to be applied to the range defined in piFRDLcRangeStart and piFRDLcRangeEnd
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), pvc(2)  

piFRDLcRangeMode 1.3.6.1.4.1.1955.5.5.3.3.1.3
For future use
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bidirectional(1)  

piFRDLcRangeStart 1.3.6.1.4.1.1955.5.5.3.3.1.4
The first DLCI in this band
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1023  

piFRDLcRangeEnd-set-to-activate-changes 1.3.6.1.4.1.1955.5.5.3.3.1.5
The last DLCI in this band Setting this parameter activates the changes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1023  

piRemotePorts 1.3.6.1.4.1.1955.5.5.3.5
OBJECT IDENTIFIER    

pi-Remote-Port1 1.3.6.1.4.1.1955.5.5.3.5.1
OBJECT IDENTIFIER    

pi-Remote-Port1IP-Address 1.3.6.1.4.1.1955.5.5.3.5.1.1
The IP address for 1, the Ethernet line
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

pi-Remote-Port1Subnet-mask 1.3.6.1.4.1.1955.5.5.3.5.1.2
The subnet mask associated with the IP address of the 1 Ethernet line. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

pi-Remote-Port1Gateway-Address 1.3.6.1.4.1.1955.5.5.3.5.1.3
The Gateway IP address for 1. The gateway is on the same network as the port, so the network bits must be identical to the port Ipaddress
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

piRemotePort2 1.3.6.1.4.1.1955.5.5.3.5.2
OBJECT IDENTIFIER    

pi-Remote-Port3 1.3.6.1.4.1.1955.5.5.3.5.3
OBJECT IDENTIFIER    

pi-Remote-Port3IP-Address 1.3.6.1.4.1.1955.5.5.3.5.3.1
The IP address for 1, the serial line
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

pi-Remote-Port3Subnet-mask 1.3.6.1.4.1.1955.5.5.3.5.3.2
The subnet mask associated with the IP address of the 3 serial line. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

pi-Remote-Port3Gateway-Address 1.3.6.1.4.1.1955.5.5.3.5.3.3
The Gateway IP address for 3. The gateway is on the same network as the port, so the network bits must be identical to the port Ipaddress
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  


pi-Remote-Port3Baudrate 1.3.6.1.4.1.1955.5.5.3.5.3.5
The Baud rate for async port 3. The other physical parameters are fixed as follows: Character Length: 8 bits Parity: none Stopbits: 1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER baud-2400(1), baud-4800(2), baud-9600(3), baud-19200(4), baud-38400(5)  

piApplication 1.3.6.1.4.1.1955.5.5.3.6
OBJECT IDENTIFIER    

pi-App-DLC-Cipher-Table 1.3.6.1.4.1.1955.5.5.3.6.1
The table of encrypted DLCIs port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Pi-App-DLC-Cipher-Entry

pi-App-DLC-Cipher-Entry 1.3.6.1.4.1.1955.5.5.3.6.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Pi-App-DLC-Cipher-Entry  

piAppDLcCipherBand 1.3.6.1.4.1.1955.5.5.3.6.1.1.1
The index number of this DLCI circuit band.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

piAppDLcCipherUse 1.3.6.1.4.1.1955.5.5.3.6.1.1.2
The Type of use (plain or cipher) to be applied to the range defined in piAppDLcCipherStart and piAppDLcCipherEnd.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER plain(1), cipher(2)  

piAppDLcCipherStart 1.3.6.1.4.1.1955.5.5.3.6.1.1.3
The first DLCI in this band
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1023  

piAppDLcCipherEnd-set-to-activate-changes 1.3.6.1.4.1.1955.5.5.3.6.1.1.4
The last DLCI in this band Setting this parameter activates the changes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1023