GDCHDSL-MIB

File: GDCHDSL-MIB.mib (76466 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
GDCMACRO-MIB

Imported symbols

Gauge enterprises TimeTicks
OBJECT-TYPE DisplayString SCinstance

Defined Types

GdcHdslVersionEntry  
SEQUENCE    
  gdcHdslVersionIndex SCinstance
  gdcHdslFirmwareRev DisplayString
  gdcHdslModelNumber DisplayString

GdcHdslDownloadEntry  
SEQUENCE    
  gdcHdslDownloadIndex SCinstance
  gdcHdslActiveFirmwareRev DisplayString
  gdcHdslStoredFirmwareRev DisplayString
  gdcHdslStoredFirmwareStatus INTEGER
  gdcHdslSwitchActiveFirmware INTEGER
  gdcHdslDownloadingMode INTEGER
  gdcHdslEraseFlash INTEGER

GdcHdslMaintenanceEntry  
SEQUENCE    
  gdcHdslMaintenanceLineIndex SCinstance
  gdcHdslSoftReset INTEGER
  gdcHdslConfigMode INTEGER
  gdcHdslSysUpTime TimeTicks
  gdcHdslUnitType INTEGER
  gdcHdslDefaultInit INTEGER
  gdcHdslDataType INTEGER
  gdcHdslLoopProvision INTEGER
  gdcHdslNumberofLoops INTEGER
  gdcHdslFrontPanel INTEGER
  gdcHdslRoutingConfig INTEGER
  gdcHdslPrivateStorage1 DisplayString
  gdcHdslPrivateStorage2 DisplayString
  gdcHdslPrivateStorage3 DisplayString
  gdcHdslLedStatus OCTET STRING
  fracExecution INTEGER
  gdcHdslAlarmStatus OCTET STRING
  gdcHdslV54Config INTEGER
  gdcHdslFPRDLConfig INTEGER
  gdcHdslRLTimeOut INTEGER
  gdcHdslRPEnable INTEGER
  gdcHdslLedStatus1 OCTET STRING

GdcHdslE1ConfigEntry  
SEQUENCE    
  gdcHdslE1ConfigIndex SCinstance
  gdcHdslE1FramingMode INTEGER
  gdcHdslE1LineUnit INTEGER
  gdcHdslE1LineCoding INTEGER

GdcHdslDteConfigEntry  
SEQUENCE    
  gdcHdslDteConfigIndex SCinstance
  gdcHdslDteCtsMode INTEGER
  gdcHdslDteDataRate INTEGER
  gdcHdslDteTxClkSource INTEGER

GdcHdslT1ConfigEntry  
SEQUENCE    
  gdcHdslT1ConfigIndex SCinstance
  gdcHdslT1InterfaceType INTEGER
  gdcHdslT1FramingMode INTEGER
  gdcHdslT1TxPreequalization INTEGER
  gdcHdslT1TxBulidOut INTEGER
  gdcHdslT1InbandLBType INTEGER
  gdcHdslT1FDLMode INTEGER
  gdcHdslT1LineCoding INTEGER
  gdcHdslT1TxClkSource INTEGER
  gdcHdslT1LineCoding INTEGER

GdcHdslDiagEntry  
SEQUENCE    
  gdcHdslDiagIndex SCinstance
  gdcHdslLoopback INTEGER
  gdcHdslBertTest INTEGER

GdcHdslDiagResultsEntry  
SEQUENCE    
  gdcHdslDiagResultsIndex SCinstance
  gdcHdslTestExecutionStatus INTEGER
  gdcHdslDiagResultErr INTEGER
  gdcHdslDiagResultInterval INTEGER
  gdcHdslV54RDLTest INTEGER

GdcHdslCurrentEntry  
SEQUENCE    
  gdcHdslCurrentIndex SCinstance
  gdcHdslCurrentESs Gauge
  gdcHdslCurrentSESs Gauge
  gdcHdslCurrentUASs Gauge
  gdcHdslCurrentDMs Gauge
  gdcHdslCurrentFEBEs Gauge
  gdcHdslCurrentStats OCTET STRING

GdcHdslIntervalEntry  
SEQUENCE    
  gdcHdslIntervalIndex SCinstance
  gdcHdslIntervalNumber INTEGER
  gdcHdslIntervalESs Gauge
  gdcHdslIntervalSESs Gauge
  gdcHdslIntervalUASs Gauge
  gdcHdslIntervalDMs Gauge
  gdcHdslIntervalFEBEs Gauge
  gdcHdslIntervalStats OCTET STRING

GdcHdslTotalEntry  
SEQUENCE    
  gdcHdslTotalIndex SCinstance
  gdcHdslTotalESs Gauge
  gdcHdslTotalSESs Gauge
  gdcHdslTotalUASs Gauge
  gdcHdslTotalDMs Gauge
  gdcHdslTotalFEBEs Gauge
  gdcHdslTotalStats OCTET STRING

GdcHdslIntervalMaintenanceEntry  
SEQUENCE    
  gdcHdslIntervalMaintenanceIndex SCinstance
  gdcHdslResetIntervals INTEGER
  gdcHdslNumberofValidIntervals INTEGER
  gdcHdslResetMajorAlarm INTEGER
  gdcHdslResetMinorAlarm INTEGER

GdcHdslT1CurrentEntry  
SEQUENCE    
  gdcHdslT1CurrentIndex SCinstance
  gdcHdslT1CurrentStats OCTET STRING

GdcHdslT1IntervalEntry  
SEQUENCE    
  gdcHdslT1IntervalIndex SCinstance
  gdcHdslT1IntervalNumber INTEGER
  gdcHdslT1IntervalStats OCTET STRING

GdcHdslT1TotalEntry  
SEQUENCE    
  gdcHdslT1TotalIndex SCinstance
  gdcHdslT1TotalStats OCTET STRING

GdcHdslLoopStatusEntry  
SEQUENCE    
  gdcHdslLoopStatusLineIndex SCinstance
  gdcHdslLoopStartUp INTEGER
  gdcHdslLoopTipRingReversalMode INTEGER
  gdcHdslLoopSignaltoNoiseMargin INTEGER
  gdcHdslLoopSNFrac INTEGER
  gdcHdslLoopSNAttenSense INTEGER
  gdcHdslLoopPulseAtten INTEGER
  gdcHdslLoopPulseAttenFrac INTEGER
  gdcHdslLoopGain INTEGER
  gdcHdslLoopExchange INTEGER

GdcHdslDteStatusEntry  
SEQUENCE    
  gdcHdslDteStatusIndex SCinstance
  gdcHdslDteDTRstatus INTEGER
  gdcHdslDteDCDstatus INTEGER
  gdcHdslDteRTSstatus INTEGER
  gdcHdslDteDSRstatus INTEGER
  gdcHdslDteStatus OCTET STRING

HdslFracEntry  
SEQUENCE    
  hdslFracIndex SCinstance
  channelmapping INTEGER
  gdcHdslHighway INTEGER
  gdcHdslTimeSlot16 INTEGER

HdslAlarmConfigEntry  
SEQUENCE    
  hdslAlarmConfigIndex SCinstance
  hdslAlarmConfigIdentifier OBJECT IDENTIFIER
  hdslAlarmThreshold INTEGER

Defined Values

gdc 1.3.6.1.4.1.498
OBJECT IDENTIFIER    

hdsl 1.3.6.1.4.1.498.11
OBJECT IDENTIFIER    

gdcHdslSystem 1.3.6.1.4.1.498.11.1
OBJECT IDENTIFIER    

hdsl700G2 1.3.6.1.4.1.498.11.2
OBJECT IDENTIFIER    

hdsl700G3 1.3.6.1.4.1.498.11.3
OBJECT IDENTIFIER    

hdsl730D1 1.3.6.1.4.1.498.11.4
OBJECT IDENTIFIER    

hdsl730D2 1.3.6.1.4.1.498.11.5
OBJECT IDENTIFIER    

hdsl720G1 1.3.6.1.4.1.498.11.6
OBJECT IDENTIFIER    

hdsl720G2 1.3.6.1.4.1.498.11.7
OBJECT IDENTIFIER    

hdsl702G2 1.3.6.1.4.1.498.11.8
OBJECT IDENTIFIER    

hdsl710D2 1.3.6.1.4.1.498.11.9
OBJECT IDENTIFIER    

hdsl700G2RP 1.3.6.1.4.1.498.11.10
OBJECT IDENTIFIER    

hdsl710D2RP 1.3.6.1.4.1.498.11.11
OBJECT IDENTIFIER    

hdsl720G2RP 1.3.6.1.4.1.498.11.12
OBJECT IDENTIFIER    

hdsl730D2RP 1.3.6.1.4.1.498.11.13
OBJECT IDENTIFIER    

hdsl701T2 1.3.6.1.4.1.498.11.14
OBJECT IDENTIFIER    

hdsl701T2RP 1.3.6.1.4.1.498.11.15
OBJECT IDENTIFIER    

hdsl721T1 1.3.6.1.4.1.498.11.16
OBJECT IDENTIFIER    

hdsl721T2 1.3.6.1.4.1.498.11.17
OBJECT IDENTIFIER    

hdsl721T2RP 1.3.6.1.4.1.498.11.18
OBJECT IDENTIFIER    

hdsl731D1 1.3.6.1.4.1.498.11.19
OBJECT IDENTIFIER    

hdsl731D2 1.3.6.1.4.1.498.11.20
OBJECT IDENTIFIER    

hdsl731D2RP 1.3.6.1.4.1.498.11.21
OBJECT IDENTIFIER    

hdsl700AG2 1.3.6.1.4.1.498.11.22
OBJECT IDENTIFIER    

hdsl700AG2NZ 1.3.6.1.4.1.498.11.23
OBJECT IDENTIFIER    

hdslGT1030 1.3.6.1.4.1.498.11.25
OBJECT IDENTIFIER    

hdslGT2030 1.3.6.1.4.1.498.11.26
OBJECT IDENTIFIER    

uas7722 1.3.6.1.4.1.498.11.27
OBJECT IDENTIFIER    

hdslGT1020 1.3.6.1.4.1.498.11.28
OBJECT IDENTIFIER    

hdslGT2020 1.3.6.1.4.1.498.11.29
OBJECT IDENTIFIER    

hdsl711D2 1.3.6.1.4.1.498.11.30
OBJECT IDENTIFIER    

gdcHdslVersion 1.3.6.1.4.1.498.11.1.1
OBJECT IDENTIFIER    

gdcHdslMaintenance 1.3.6.1.4.1.498.11.1.2
OBJECT IDENTIFIER    

gdcHdslConfiguration 1.3.6.1.4.1.498.11.1.3
OBJECT IDENTIFIER    

gdcHdslDiagnostics 1.3.6.1.4.1.498.11.1.4
OBJECT IDENTIFIER    

gdcHdslPerformance 1.3.6.1.4.1.498.11.1.5
OBJECT IDENTIFIER    

gdcHdslStatus 1.3.6.1.4.1.498.11.1.6
OBJECT IDENTIFIER    

gdcHdslDiagnosticResults 1.3.6.1.4.1.498.11.1.7
OBJECT IDENTIFIER    

gdcFractional 1.3.6.1.4.1.498.11.1.8
OBJECT IDENTIFIER    

gdcHdslAlarmThresholds 1.3.6.1.4.1.498.11.1.9
OBJECT IDENTIFIER    

gdcHdslSystemMIBversion 1.3.6.1.4.1.498.11.1.1.1
Identifies the version of the MIB. The format of the version is x.yzT, where 'x' identifies the major revision number, 'y' identifies the minor revision number, 'z' identifies the typographical revision, and T identifies the test revision. Acceptable values for the individual revision components are as follows: x: 1 - 9 y: 0 - 9 z: 0 - 9 T: A - Z Upon formal release, no designation for the test revision will be present.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(5)  

gdcHdslVersionTable 1.3.6.1.4.1.498.11.1.1.2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslVersionEntry

gdcHdslVersionEntry 1.3.6.1.4.1.498.11.1.1.2.1
An entry in the GDC Hdsl Version Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslVersionEntry  

gdcHdslVersionIndex 1.3.6.1.4.1.498.11.1.1.2.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and sub-identifier. The table describes the maintenance objects for the unit and references the unit interface (cc = 00).
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslFirmwareRev 1.3.6.1.4.1.498.11.1.1.2.1.2
The version number of the firmware, to allow products to know which revision is installed. The released version number is sequenced from , A-, ... AA, ... ZZ. Test versions are numerical from 01 to 99.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2)  

gdcHdslModelNumber 1.3.6.1.4.1.498.11.1.1.2.1.3
This variable is used to determine the type of card family installed ex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

gdcHdslDownloadTable 1.3.6.1.4.1.498.11.1.1.3
The Hdsl download table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslDownloadEntry

gdcHdslDownloadEntry 1.3.6.1.4.1.498.11.1.1.3.1
An entry in the GDC gdcHdslSystem Download Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslDownloadEntry  

gdcHdslDownloadIndex 1.3.6.1.4.1.498.11.1.1.3.1.1
Integer value which uniquely identifies the GDCHDSL to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00-31) i (byte value) - loop or interface number (00-03)
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslActiveFirmwareRev 1.3.6.1.4.1.498.11.1.1.3.1.2
The version number of the firmware currently executing. The format is MM.NN.BB where: MM: Major Revision (0-99) NN: Minor Revision (0-99) BB: Bug Fix Revision (0-99) Valid [i]nterface = 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(8)  

gdcHdslStoredFirmwareRev 1.3.6.1.4.1.498.11.1.1.3.1.3
The version number of the firmware stored (in a compressed format) but not currently executing. MM: Major Revision (0-99) NN: Minor Revision (0-99) BB: Bug Fix Revision (0-99) Valid [i]nterface = 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(8)  

gdcHdslStoredFirmwareStatus 1.3.6.1.4.1.498.11.1.1.3.1.4
This object represents the state of the Non-Active or Stored firmware: statBlank(1) Factory Default statDownLoading(2) In process of downloading firmware statOK(3) Zipped version checksum succesful (OK to switch) (can set gdcHdslSwitchActiveFirmware to switchActive(2)) statCheckSumBad(4) Failed checksum after download statUnZipping(5) In process of uncompressing into active area statBadUnZip(6) Failed last uncompress statDownloadAborted(7) Download aborted by user Valid [i]nterface = 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER statBlank(1), statDownLoading(2), statOK(3), statCheckSumBad(4), statUnZipping(5), statBadUnZip(6), statDownloadAborted(7)  

gdcHdslSwitchActiveFirmware 1.3.6.1.4.1.498.11.1.1.3.1.5
This object is used to switch the active executing firmware from the version in gdcHdslActiveFirmwareRev to the version in gdcHdslStoredFirmwareRev. When a switchActive(2) is set (write only) the element will: 1) reboot 2) uncompress stored code into active area 3) perform checksum on active area 4) Set gdcHdslStoredStatus object to indicate results 5) If succesfull: update gdcHdslActiveFirmwareRev and gdcHdslStoredFirmwareRev and begin executing If failed: replace active area with previous revision The switchNorm(1) enumeration will always be read. Setting switchActive(2) when the gdcHdslStoredFirmwareStatus is not statOK(3) will result in an error. Valid [i]nterface = 0
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER switchNorm(1), switchActive(2)  

gdcHdslDownloadingMode 1.3.6.1.4.1.498.11.1.1.3.1.6
This object is used to configure the download mode: disableAll(1) Prevents any firmware downloading to GDCHDSL enableAndWait(2) Allows downloading zipped code to be stored only! enableAndSwitch(3) Allows downloading and then unzips and begins executing the new code Valid [i]nterface = 0
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disableAll(1), enableAndWait(2), enableAndSwitch(3)  

gdcHdslEraseFlash 1.3.6.1.4.1.498.11.1.1.3.1.7
A set of this object to erase(2) will erase the application stored in flash. After setting this object, there should be a delay of at least 2 minutes before downloading the unit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), erase(2)  

gdcHdslMaintenanceTable 1.3.6.1.4.1.498.11.1.2.1
The table describes the maintenance objects for the unit and references the unit interface (cc = 00).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslMaintenanceEntry

gdcHdslMaintenanceEntry 1.3.6.1.4.1.498.11.1.2.1.1
An entry in the GDC HDSL Maintenance Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslMaintenanceEntry  

gdcHdslMaintenanceLineIndex 1.3.6.1.4.1.498.11.1.2.1.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and sub-identifier. The table describes the maintenance objects for the unit and references the unit interface (cc = 00).
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslSoftReset 1.3.6.1.4.1.498.11.1.2.1.1.2
Supports the action of soft resetting the unit. When this object is set to reset(1), then the unit performs a soft reset, whose meaning is specific to the type of unit being managed. The value norm(2) can not be set by management.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), norm(2)  

gdcHdslConfigMode 1.3.6.1.4.1.498.11.1.2.1.1.3
The hardware configuration mode of the unit. A unit may be configured through hardware switches, jumper, straps, etc. The value software(1) indicates that the unit is software configurable. The value of hardware(2) indicates that some options are hard configured and that software configuration is not permitted of these options.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

gdcHdslSysUpTime 1.3.6.1.4.1.498.11.1.2.1.1.4
This variable is used to report the elapsed system tick time for conversion to real time at the controller and is not related to the sysUpTime referenced in MIB-II. Upon power-up of the unit, the elapsed time is cleared. The elapsed time counter rolls over upon reaching the maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

gdcHdslUnitType 1.3.6.1.4.1.498.11.1.2.1.1.5
This variable is used to define HDSL unit type. When this object is set to ltu(1), the unit is a Line Terminating Unit and serves as master. When this object is set to ntu(2), the unit is a network terminating unit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ltu(1), ntu(2)  

gdcHdslDefaultInit 1.3.6.1.4.1.498.11.1.2.1.1.6
This is used to allow the NonVolatile Configuration to be set to a factory default state. When this value is set to factoryDefault(1) the unit will perform a reset to make the default configuration take affect. The value of normal(2) will be returned when the initialization is complete. The value normal(2) can not be set by management.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER factoryDefault(1), normal(2)  

gdcHdslDataType 1.3.6.1.4.1.498.11.1.2.1.1.7
This variable is used to define the HDSL data type. When this object is set to data(2) the data pass through the unit is digital data. When is set to voice(1) the data pass rhrough the unit is voice data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER voice(1), data(2)  

gdcHdslLoopProvision 1.3.6.1.4.1.498.11.1.2.1.1.8
This variable is used to define HDSL unit loop provision. When this variable is set to pointopoint(1), the unit is connected to another HDSL unit. When is set to pointomultipoint(2), the unit is connected to more than one other HDSL units or data grooming.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER pointopoint(1), pointomultipoint(2)  

gdcHdslNumberofLoops 1.3.6.1.4.1.498.11.1.2.1.1.9
This variable is used to define HDSL unit loop configuration. It can be set for one to threee loops.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER oneLoop(1), twoLoops(2), threeLoops(3)  

gdcHdslFrontPanel 1.3.6.1.4.1.498.11.1.2.1.1.10
This variable is used to define the front Panel operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inhibit(1), enable(2)  

gdcHdslRoutingConfig 1.3.6.1.4.1.498.11.1.2.1.1.11
This variable is used to define HDSL ......
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER twoLoops(1), threeLoops(2)  

gdcHdslPrivateStorage1 1.3.6.1.4.1.498.11.1.2.1.1.12
This variable is used for general purpose storage.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(16)  

gdcHdslPrivateStorage2 1.3.6.1.4.1.498.11.1.2.1.1.13
This variable is used for general purpose storage.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(16)  

gdcHdslPrivateStorage3 1.3.6.1.4.1.498.11.1.2.1.1.14
This variable is used for general purpose storage.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(16)  

gdcHdslLedStatus 1.3.6.1.4.1.498.11.1.2.1.1.15
Returns a bitwise snapshot of the front panel LED state. Octet 1 bit 7 - not used bit 6 - not used bit 5 - not used bit 4 - not used bit 3 - NORM E1 bit 2 - ES E1 bit 1 - AL bit 0 - TM Octet 2 bit 7 - not used bit 6 - not used bit 5 - NORM L3 bit 4 - ES L3 bit 3 - NORM L2 bit 2 - ES L2 bit 1 - NORM L1 bit 0 - ES L1
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

fracExecution 1.3.6.1.4.1.498.11.1.2.1.1.16
For Set, only execute is allowed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER execute(1), norm(2)  

gdcHdslAlarmStatus 1.3.6.1.4.1.498.11.1.2.1.1.17
The current alarms of the unit without the alarm masks.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..255)  

gdcHdslV54Config 1.3.6.1.4.1.498.11.1.2.1.1.18
This object selects the ability of the unit to recognize V.54 pattern. Only applicable to DC730 & DC731 units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inhibit(1), enabled(2)  

gdcHdslFPRDLConfig 1.3.6.1.4.1.498.11.1.2.1.1.19
This object selects the pattern to be transmitted when RDL test is selected via the front panel RDL switch. Only applicable to DC730 & DC731 units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER eoc(1), v54(2)  

gdcHdslRLTimeOut 1.3.6.1.4.1.498.11.1.2.1.1.20
This object selects the RLTimeOut to be disabled(1) or set to 10 minutes(2). Only applicable to SC710D2 units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), mins10(2)  

gdcHdslRPEnable 1.3.6.1.4.1.498.11.1.2.1.1.21
This object selects the Remote power to be enabled(2) or disabled(1). Only applicable RP products which are on the shelf.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inhibit(1), enable(2)  

gdcHdslLedStatus1 1.3.6.1.4.1.498.11.1.2.1.1.22
Returns a bitwise snapshot of the front panel LED state. This mib object is only used for the new HDSl elements. Octet 1 bit 7 - not used bit 6 - EIA RD bit 5 - EIA CO bit 4 - EIA RS bit 3 - NORM E1/T1 NORM bit 2 - ES E1/T1 ER bit 1 - AL bit 0 - TM Octet 2 bit 7 - not used bit 6 - EIA SD bit 5 - NORM L3 bit 4 - ES L3 bit 3 - NORM L2 bit 2 - ES L2 bit 1 - NORM L1 bit 0 - ES L1 Octet 3 bit 7 - not used bit 6 - not used bit 5 - ST (GT10xx, GT20xx) bit 4 - RL (GT10xx, GT20xx) bit 3 - LL (GT10xx, GT20xx) bit 2 - INS (uas7722) bit 1 - RPF FAULT bit 0 - RPF NORM
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

gdcHdslE1ConfigTable 1.3.6.1.4.1.498.11.1.3.1
The GDC E1 Configuration table. Information in the entries of this table are used to configure E1 interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslE1ConfigEntry

gdcHdslE1ConfigEntry 1.3.6.1.4.1.498.11.1.3.1.1
The GDC E1 Configuration table entry. The information in this entry augments are used to configure E1 interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslE1ConfigEntry  

gdcHdslE1ConfigIndex 1.3.6.1.4.1.498.11.1.3.1.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and sub-identifier. In which this case is an E1 interface (cc=01).
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslE1FramingMode 1.3.6.1.4.1.498.11.1.3.1.1.2
This variable is used to determine E1 framing mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER framed(1), unframed(2)  

gdcHdslE1LineUnit 1.3.6.1.4.1.498.11.1.3.1.1.3
This variable is used to determine operating mode of the HDSL system with respect to E1 trunk. When this variable is set to tlu(1), the system operates as a termination line unit. When this variable is set to ilu(2) the system operates as an intermediate line unit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tlu(1), ilu(2)  

gdcHdslE1LineCoding 1.3.6.1.4.1.498.11.1.3.1.1.4
This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. E1 links, with or without CRC, use HDB3 or AMI. AMI refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ami(1), hdb3(2)  

gdcHdslDteConfigTable 1.3.6.1.4.1.498.11.1.3.2
The GDC DTE Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslDteConfigEntry

gdcHdslDteConfigEntry 1.3.6.1.4.1.498.11.1.3.2.1
The GDC DTE Configuration table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslDteConfigEntry  

gdcHdslDteConfigIndex 1.3.6.1.4.1.498.11.1.3.2.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslDteCtsMode 1.3.6.1.4.1.498.11.1.3.2.1.2
This variable controls the function of CTS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER forcedOn(1), onWithRts(2)  

gdcHdslDteDataRate 1.3.6.1.4.1.498.11.1.3.2.1.3
This variable represents the DTE data Rate in 64K increments.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

gdcHdslDteTxClkSource 1.3.6.1.4.1.498.11.1.3.2.1.4
The source of Tranmit Clock. 'ExternalTiming' indicates that recovered re- ceive clock from another interface is used as the transmit clock. 'InternalTiming' indicates that a local clock source is used. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER externalTiming(1), internalTiming(2), loopTiming(3)  

gdcHdslT1ConfigTable 1.3.6.1.4.1.498.11.1.3.3
The GDC T1 Configuration table. Information in the entries of this table are used to configure T1 interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslT1ConfigEntry

gdcHdslT1ConfigEntry 1.3.6.1.4.1.498.11.1.3.3.1
The GDC T1 Configuration table entry. The information in this entry augments are used to configure T1 interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslT1ConfigEntry  

gdcHdslT1ConfigIndex 1.3.6.1.4.1.498.11.1.3.3.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and sub-identifier. In which this case is an T1 interface (cc=01).
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslT1InterfaceType 1.3.6.1.4.1.498.11.1.3.3.1.2
This variable is used to set T1 Interface Type
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dsx1(1), ds1(2)  

gdcHdslT1FramingMode 1.3.6.1.4.1.498.11.1.3.3.1.3
This variable is used to determine T1 framing mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER esfANSI(1), esf54016(2), sf(3), unframed(4)  

gdcHdslT1TxPreequalization 1.3.6.1.4.1.498.11.1.3.3.1.4
This variable is used to set T1 Tx Line Preequalization
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER preq0to133ft(1), preq133to266ft(2), preq266to399ft(3), preq399to533ft(4), preq533to655ft(5)  

gdcHdslT1TxBulidOut 1.3.6.1.4.1.498.11.1.3.3.1.5
This variable is used to set T1 Tx Line Bulid Out
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER bo0dB(1), bo75dB(2), bo150dB(3), bo225dB(4)  

gdcHdslT1InbandLBType 1.3.6.1.4.1.498.11.1.3.3.1.6
This variable is used to set T1 Inband LoopBack Type or Inhibit(1) this loopback
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inhibit(1), lineloopback(2), payloadloopback(3)  

gdcHdslT1FDLMode 1.3.6.1.4.1.498.11.1.3.3.1.7
This variable is used to enable/disable T1 FDL Mode
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

gdcHdslT1AISLoopdownTime 1.3.6.1.4.1.498.11.1.3.3.1.8
This variable is used to set T1 AIS Loopdown Time
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inhibit(1), ld5secs(2), ld10secs(3), ld20secs(4), ld40secs(5), ld60secs(6)  

gdcHdslT1LineCoding 1.3.6.1.4.1.498.11.1.3.3.1.9
This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. E1 links, with or without CRC, use HDB3 or AMI. AMI refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ami(1), b8zs(2)  

gdcHdslT1TxClkSource 1.3.6.1.4.1.498.11.1.3.3.1.10
The source of Tranmit Clock. 'ExternalTiming' indicates that recovered re- ceive clock from another interface is used as the transmit clock. 'InternalTiming' indicates that a local clock source is used. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER externalTiming(1), internalTiming(2), loopTiming(3)  

gdcHdslDiagTable 1.3.6.1.4.1.498.11.1.4.1
The GDC HDSL Diagnostics table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslDiagEntry

gdcHdslDiagEntry 1.3.6.1.4.1.498.11.1.4.1.1
The GDC HDSL Diagnostics table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslDiagEntry  

gdcHdslDiagIndex 1.3.6.1.4.1.498.11.1.4.1.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and sub-identifier, which in this case is a network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslLoopback 1.3.6.1.4.1.498.11.1.4.1.1.2
This variable supports the action of a diagnostic loop at the point indicated. dataLoop & remoteLoop are only supported by uas7722
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noLoop(1), lineLoop(2), localLoop(3), lineandlocalLoop(4), dataLoop(6), remoteLoop(7)  

gdcHdslBertTest 1.3.6.1.4.1.498.11.1.4.1.1.3
This variable supports the action of Bit error rate test. When set to inhibit(1) no bert test is in process. When set to enable (2) BERT is in process
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inhibit(1), enable(2), reset(3)  

gdcHdslDiagResultsTable 1.3.6.1.4.1.498.11.1.7.1
The GDC HDSL Diagnostics table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslDiagResultsEntry

gdcHdslDiagResultsEntry 1.3.6.1.4.1.498.11.1.7.1.1
The GDC HDSL Diagnostics table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslDiagResultsEntry  

gdcHdslDiagResultsIndex 1.3.6.1.4.1.498.11.1.7.1.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and sub-identifier, which in this case is a network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslTestExecutionStatus 1.3.6.1.4.1.498.11.1.7.1.1.2
The current execution status of the diagnostic test. When set to inSync(1), BERT test is in sync and BER rate is valid. When set to notInSync(2), BERT test is not in Sync and BER rate is not valid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inSync(1), notInSync(2)  

gdcHdslDiagResultErr 1.3.6.1.4.1.498.11.1.7.1.1.3
The results of the last diagnostic test. This can be the current test running or the last completed test. Note that the interpretation of these results may be affected by the value of the gdcTestExecutionStatus object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

gdcHdslDiagResultInterval 1.3.6.1.4.1.498.11.1.7.1.1.4
This variable represents the Ber test intervals. A time interval is defined as the time required for transmission of a block of 2^24 bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

gdcHdslV54RDLTest 1.3.6.1.4.1.498.11.1.7.1.1.5
This variable indicates that the front panel RL button is selected and transmitting a V54 pattern. Applicable only to DC730 units.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notInV54Test(1), txV54Test(2)  

gdcHdslCurrentTable 1.3.6.1.4.1.498.11.1.5.1
The GDC Hdsl Current Performance table. Information in the entries of this table support the HDSL Scheduled Performance Reports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslCurrentEntry

gdcHdslCurrentEntry 1.3.6.1.4.1.498.11.1.5.1.1
An entry in the Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslCurrentEntry  

gdcHdslCurrentIndex 1.3.6.1.4.1.498.11.1.5.1.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, which in this case can be an E1 or Loop interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslCurrentESs 1.3.6.1.4.1.498.11.1.5.1.1.2
The number of Errored Seconds, encountered by an E1 or Loop interface in the current 15 minute inter- val.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslCurrentSESs 1.3.6.1.4.1.498.11.1.5.1.1.3
The number of Severely Errored Seconds encoun- tered by a Loop or E1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslCurrentUASs 1.3.6.1.4.1.498.11.1.5.1.1.4
The number of Unavailable Seconds encountered by a Loop or E1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslCurrentDMs 1.3.6.1.4.1.498.11.1.5.1.1.5
The number of Degraded Minutes (DMs) encoun- tered by a Loop or E1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslCurrentFEBEs 1.3.6.1.4.1.498.11.1.5.1.1.6
The number of Far End Block Errors encountered by a Loop or E1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslCurrentStats 1.3.6.1.4.1.498.11.1.5.1.1.7
The number of Current ES, SES, UAS, DM and FEBE's encountered by a Loop or E1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(15)  

gdcHdslIntervalTable 1.3.6.1.4.1.498.11.1.5.2
The Loop or E1 Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslIntervalEntry

gdcHdslIntervalEntry 1.3.6.1.4.1.498.11.1.5.2.1
An entry in the Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslIntervalEntry  

gdcHdslIntervalIndex 1.3.6.1.4.1.498.11.1.5.2.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, which in this case is a Loop or E1 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslIntervalNumber 1.3.6.1.4.1.498.11.1.5.2.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming that all 96 intervals are valid).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

gdcHdslIntervalESs 1.3.6.1.4.1.498.11.1.5.2.1.3
The number of Errored Seconds encountered by a Loop or E1 interface in one of the previous 96, indi- vidual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslIntervalSESs 1.3.6.1.4.1.498.11.1.5.2.1.4
The number of Severely Errored Seconds encoun- tered by a Loop or E1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslIntervalUASs 1.3.6.1.4.1.498.11.1.5.2.1.5
The number of Unavailable Seconds encountered by a Loop or E1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslIntervalDMs 1.3.6.1.4.1.498.11.1.5.2.1.6
The number of Degraded Minutes (DMs) encoun- tered by a Loop or E1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslIntervalFEBEs 1.3.6.1.4.1.498.11.1.5.2.1.7
This variable represents the HDSL loops Far end block errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslIntervalStats 1.3.6.1.4.1.498.11.1.5.2.1.8
This variable represents stats at the HDSL loops.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(15)  

gdcHdslTotalTable 1.3.6.1.4.1.498.11.1.5.3
The GDC HDSL Total Performance table. Information in the entries of this table support the HDSL Scheduled Performance Reports. 24 hour interval.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslTotalEntry

gdcHdslTotalEntry 1.3.6.1.4.1.498.11.1.5.3.1
An entry in the Total table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslTotalEntry  

gdcHdslTotalIndex 1.3.6.1.4.1.498.11.1.5.3.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, which in this case is a Loop or E1 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslTotalESs 1.3.6.1.4.1.498.11.1.5.3.1.2
The number of Errored Seconds encountered by a Loop or E1interface in the previous 24 hour interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslTotalSESs 1.3.6.1.4.1.498.11.1.5.3.1.3
The number of Severely Errored Seconds encoun- tered by a Loop or E1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslTotalUASs 1.3.6.1.4.1.498.11.1.5.3.1.4
The number of Unavailable Seconds encountered by a Loop or E1 interface in the previous 24 hour in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslTotalDMs 1.3.6.1.4.1.498.11.1.5.3.1.5
The number of Degraded Minutes (DMs) encoun- tered by a Loop or E1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslTotalFEBEs 1.3.6.1.4.1.498.11.1.5.3.1.6
The number of Far End Block Errors en- countered by a Loop or E1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

gdcHdslTotalStats 1.3.6.1.4.1.498.11.1.5.3.1.7
The number of Total stats encountered by a Loop or E1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(15)  

gdcHdslIntervalMaintenanceTable 1.3.6.1.4.1.498.11.1.5.4
The GDC Loop/E1/T1 Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslIntervalMaintenanceEntry

gdcHdslIntervalMaintenanceEntry 1.3.6.1.4.1.498.11.1.5.4.1
The GDC Loop/E1/T1 Interval table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslIntervalMaintenanceEntry  

gdcHdslIntervalMaintenanceIndex 1.3.6.1.4.1.498.11.1.5.4.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, which in this case is a Loop or E1/T1 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslResetIntervals 1.3.6.1.4.1.498.11.1.5.4.1.2
This variable is used to reset Loop/E1/T1 performance intervals. When it is set to reset, the Loop/E1/T1 performance tables are reset to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER norm(1), reset(2)  

gdcHdslNumberofValidIntervals 1.3.6.1.4.1.498.11.1.5.4.1.3
This variable is used to read the number of intervals collected. Each interval is an increment of 15 minutes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

gdcHdslResetMajorAlarm 1.3.6.1.4.1.498.11.1.5.4.1.4
This variable is used to reset alarm per Loop basis.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clearAlarm(1), normalAlarm(2)  

gdcHdslResetMinorAlarm 1.3.6.1.4.1.498.11.1.5.4.1.5
This variable is used to reset alarm per Loop basis.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clearAlarm(1), normalAlarm(2)  

gdcHdslT1CurrentTable 1.3.6.1.4.1.498.11.1.5.5
The GDC Hdsl Current Performance table. Information in the entries of this table support the HDSL Scheduled Performance Reports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslT1CurrentEntry

gdcHdslT1CurrentEntry 1.3.6.1.4.1.498.11.1.5.5.1
An entry in the Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslT1CurrentEntry  

gdcHdslT1CurrentIndex 1.3.6.1.4.1.498.11.1.5.5.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, which in this case can be an T1 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslT1CurrentStats 1.3.6.1.4.1.498.11.1.5.5.1.2
The number of Current ES, SES, UAS, BES,LOFC,CSS. encountered by T1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(16)  

gdcHdslT1IntervalTable 1.3.6.1.4.1.498.11.1.5.6
The T1 Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslT1IntervalEntry

gdcHdslT1IntervalEntry 1.3.6.1.4.1.498.11.1.5.6.1
An entry in the Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslT1IntervalEntry  

gdcHdslT1IntervalIndex 1.3.6.1.4.1.498.11.1.5.6.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, which in this case is T1 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslT1IntervalNumber 1.3.6.1.4.1.498.11.1.5.6.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming that all 96 intervals are valid).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

gdcHdslT1IntervalStats 1.3.6.1.4.1.498.11.1.5.6.1.3
This variable represents stats(ES, SES, UAS, BES,LOFC,CSS.) for T1 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(16)  

gdcHdslT1TotalTable 1.3.6.1.4.1.498.11.1.5.7
The GDC HDSL Total Performance table. Information in the entries of this table support the HDSL Scheduled Performance Reports. 24 hour interval.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslT1TotalEntry

gdcHdslT1TotalEntry 1.3.6.1.4.1.498.11.1.5.7.1
An entry in the Total table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslT1TotalEntry  

gdcHdslT1TotalIndex 1.3.6.1.4.1.498.11.1.5.7.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, which in this case is T1 interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslT1TotalStats 1.3.6.1.4.1.498.11.1.5.7.1.2
The number of Total stats encountered by T1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(16)  

gdcHdslLoopStatusTable 1.3.6.1.4.1.498.11.1.6.1
The table describes the Status objects for the loops and references the loop interfaces (cc = 02-04).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslLoopStatusEntry

gdcHdslLoopStatusEntry 1.3.6.1.4.1.498.11.1.6.1.1
An entry in the GDC HDSL Status Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslLoopStatusEntry  

gdcHdslLoopStatusLineIndex 1.3.6.1.4.1.498.11.1.6.1.1.1
This object identifies Status parameters associated with the managed object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslLoopStartUp 1.3.6.1.4.1.498.11.1.6.1.1.2
Supports the action of initializing HDSL loop startup sequence. When set to start(2), HDSL unit will reinitialize the start up sequence. When set to cancel(3), the unit will abort the start up sequence. When set to norm(1), the unit will operate normal.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER norm(1), start(2), cancel(3)  

gdcHdslLoopTipRingReversalMode 1.3.6.1.4.1.498.11.1.6.1.1.3
Signals the loop Tip and Ring status. When norm(1), loop operates normal. When reverse(2), loop Tip and Ring have been reversed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER norm(1), reversed(2)  

gdcHdslLoopSignaltoNoiseMargin 1.3.6.1.4.1.498.11.1.6.1.1.4
Represents the loop signal to noise margin in dB units.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..127  

gdcHdslLoopSNFrac 1.3.6.1.4.1.498.11.1.6.1.1.5
This variable is used to be used with the gdcHdslLoopSignaltoNoiseMargin variable if the following manor: a) Only the values 0 and 5 are allowed. b) The value of zero means gdcHdslLoopSignaltoNoiseMargin is a whole number. c) The value of five means gdcHdslLoopSignaltoNoiseMargin is a real number and that 0.5 must be added to it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..5  

gdcHdslLoopSNAttenSense 1.3.6.1.4.1.498.11.1.6.1.1.6
This variable identifies the sense of the gdcHdslLoopSignaltoNoiseMargin variable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER positive(1), negative(2)  

gdcHdslLoopPulseAtten 1.3.6.1.4.1.498.11.1.6.1.1.7
Represents twice the HDSL loop Pulse Attenuation level in dB units.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

gdcHdslLoopPulseAttenFrac 1.3.6.1.4.1.498.11.1.6.1.1.8
This variable is used to be used with the gdcHdslLoopPulseAtten variable if the following manor: a) Only the values 0 and 5 are allowed. b) The value of zero means gdcHdslLoopPulseAtten is a whole number. c) The value of five means gdcHdslLoopPulseAtten is a real number and that 0.5 must be added to it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..5  

gdcHdslLoopGain 1.3.6.1.4.1.498.11.1.6.1.1.9
Represents the HDSL loop gain setting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER low(1), high(2), ok(3)  

gdcHdslLoopExchange 1.3.6.1.4.1.498.11.1.6.1.1.10
This variable is used to represent the HDSL loop status. When the value is returned to norm(1), HDSL loops are correctly connected. When the value is returned as exchange(2), the HDSl loop has been interchange by error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER norm(1), exchange(2)  

gdcHdslDteStatusTable 1.3.6.1.4.1.498.11.1.6.2
The GDC DTE Status table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GdcHdslDteStatusEntry

gdcHdslDteStatusEntry 1.3.6.1.4.1.498.11.1.6.2.1
The GDC DTE Configuration table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GdcHdslDteStatusEntry  

gdcHdslDteStatusIndex 1.3.6.1.4.1.498.11.1.6.2.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

gdcHdslDteDTRstatus 1.3.6.1.4.1.498.11.1.6.2.1.2
DTR EIA status indicator
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

gdcHdslDteDCDstatus 1.3.6.1.4.1.498.11.1.6.2.1.3
CO EIA status indicator
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

gdcHdslDteRTSstatus 1.3.6.1.4.1.498.11.1.6.2.1.4
RTS EIA indicator
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

gdcHdslDteDSRstatus 1.3.6.1.4.1.498.11.1.6.2.1.5
DSR EIA indicator
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

gdcHdslDteStatus 1.3.6.1.4.1.498.11.1.6.2.1.6
Dte leads status P1.7 not used .6 EIA DCD .5 EIA DTR .4 EIA RTS .3 EIA DSR .2 not used .1 not used .0 not used
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

hdslFracTable 1.3.6.1.4.1.498.11.1.8.1
The DS1 Fractional table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HdslFracEntry

hdslFracEntry 1.3.6.1.4.1.498.11.1.8.1.1
An entry in the DS1 Fractional table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  HdslFracEntry  

hdslFracIndex 1.3.6.1.4.1.498.11.1.8.1.1.1
The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

channelmapping 1.3.6.1.4.1.498.11.1.8.1.1.2
The object contains the channel mapping for multipoint. Time slot 0 is used in all loops. P1.8 f/u P1.7 \ P1.6 \ P1.5 \ P1.4 \ This byte contains the starting time slot P1.3 / P1.2 / P1.1 / P1.0 / P2.8 f/u P2.7 \ P2.6 \ P2.5 \ P2.4 \ This byte contains the number of consecutive time slots P2.3 / P2.2 / P2.1 / P2.0 /
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

gdcHdslHighway 1.3.6.1.4.1.498.11.1.8.1.1.3
Object to select the data highway for Loop n.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notAssigned(1), highway1(2), highway2(3), highway3(4), highway4(5), highway5(6), highway6(7), highway7(8), highway8(9)  

gdcHdslTimeSlot16 1.3.6.1.4.1.498.11.1.8.1.1.4
Object to select if Time Slot 16 is being used either to pass data, or skipped from passing any data for Loop n.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER used(1), skipped(2)  

hdslAlarmConfigTable 1.3.6.1.4.1.498.11.1.9.1
The hdslAlarmConfigTable contains entries that configure alarm reporting. The structure of the table is such that alarm configuration is supported on a unit and interface basis, and then on an alarm type basis within the interface. For simplicity sake alarms, be they unit or interface related, are represented in one table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HdslAlarmConfigEntry

hdslAlarmConfigEntry 1.3.6.1.4.1.498.11.1.9.1.1
An entry in the hdslAlarmConfigTable table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  HdslAlarmConfigEntry  

hdslAlarmConfigIndex 1.3.6.1.4.1.498.11.1.9.1.1.1
The index value which uniquely identifies the interface to which this entry is applicable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

hdslAlarmConfigIdentifier 1.3.6.1.4.1.498.11.1.9.1.1.2
The unique alarm identifier assigned to this alarm type. The format of this identifier is an OBJECT IDENTIFIER that has the following format: {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) gdc(498) xxx(x) alarm(z) yyy(y) where xxx(x) is the administratively assigned family object identifier (z) is the object identifier for alarms in the family defined MIB and yyy(y) is the administratively assigned alarm type identifier for this alarm.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

hdslAlarmThreshold 1.3.6.1.4.1.498.11.1.9.1.1.3
This function sets/reads the Major or Minor BER alarm threshold criteria.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER thres1E04(1), thres1E05(2), thres1E06(3), thres1E07(4), thres1E08(5)